Search Documents

By Merete Tangstad, Eli Ringdalen

"In Norway ferrosilicon/silicon and ferromanganese production are strong with world markets of 4 % / 9 % and 4 %, respectively. Research and development in the academia mirrors the national interest; hence, there has been extensive academic research in these areas. There are some vital drivers and premises for a successful cooperation between the academia and industry with the main driver being a win-win situation for both. For industry,the potential advantages include cost-, competence- or environmental- benefits; for academia, the important drivers are building of competence and equipment, educating more students at higher levels, and increased possibilities to publish. In Norway, the benefits of cooperation between industry and academia are basic knowledge regarding thermodynamic and kinetic data, as well as reaction mechanisms within core processes. In recent years, such research interests have focused on the depletion of raw materials as well as environmental issues.IntroductionIn 1989, the Norwegian Ferroalloy Producers Research Association (FFF) was funded on the belief that a common research association would benefit the industry by making it easier to perform basic research as well as paving the ground for better recruitment to the industry. The funding partners in Norway were the FeSi/Si and FeMn producers. Today, the producers are Elkem, Finnfjord, Fesil, Wacker, Eramet and Vale. The main research partners working with FFF are SINTEF (Materials and Chemistry) and the Department of Material Science and Engineering at the Norwegian University of Science and Technology (NTNU). With more than 1700 employees, SINTEF is the largest independent research organization in Norway and NTNU is the largest technical university. Together, the two organizations provide an exceptionally strong materials technology research environment, and especially so for pyrometallurgical research."

Jan 1, 2012

By L. Yin, R. B. Haber, N. Sobh, D. A. Tortorelli, R. W. Hyland Jr.

"We optimize continuous quench process parameters to produce a desired precipitate distribution in aluminum alloy extrudates. To perform this task, an optimization problem is defined and solved using a standard nonlinear programming algorithm. Ingredients of this algorithm include a cost function, constraint functions and their sensitivities with respect to the process parameters. These functions are dependent on the temperature and precipitate size which are obtained by balancing energy to determine the temperature distribution and by using a reaction-rate theory to determine a discrete precipitate particle size distribution. Both the temperature and the precipitate models are solved via the finite element method. Since we use a discrete particle size model, there are as many as 105 degrees-of-freedom per finite element node. After we compute the temperature and precipitate size distributions, we must also compute their sensitivities. This seemingly intractable computational task is resolved by using an element-by-element discontinuous Galerkin finite element formulation and a direct differentiation sensitivity analysis which allows us to perform all of the computations on a PC.1 IntroductionThis work addresses the need for an integrated design capability that links microstructure evolution to the process parameters. It is motivated by the manufacture of lightweight aluminum-alloy extrusions for use in automotive structures. Aluminum alloys offer obvious benefits, however, care must be taken to manufacture favorable microstructures that ensure acceptable structural performance. For example, the manufacturing process for 6000-series components involves hot extrusion of cast aluminum billets followed by either an air or water quench process. The bill~t's initial grain structure is dramatically altered during extrusion by massive mechanical deformations and recrystallization processes. The microstructure continues to evolve during the quench, as complex chemical processes determine the formation of precipitates. The control of the precipit'ate size distribution is vital. Indeed, large precipitates located on grain boundaries serve as crack initiation sites which adversely effect structural crash· worthiness."

Jan 1, 2000

By Xiang Lan

A strain of Thiobacillus ferruuxidans No. 8 was isolated from the acidic mine water of an arsenopyrite deposit, South China. It has been found from the experimental results that the growth of bacteria was inhibited by flotation agents. The order of toxic effect of different flotation agents on the growth of Thiobacillus ferrooxidans is ethyl xanthate > butyat ammonium aerofloat > butyl xanthate ? isobutyt xauthate >? flother No. 2 oil. The bioteaching treatment of arsenic and antimony-bearing gold concentrate in Longshan mine, Hunan province, China, was influenced considerably by the presence of flotation agents. The possible causes of the influence of flotation agents were discussed and an improved method was suggested.

Jan 1, 1991

By Carla Lupi

In this work, nickel-cobalt electrodeposition under galvanostatic conditions was investigated. Ni-Co alloy was electrowon from an acid sulphate bath containing 40 g/L Ni and2-8 g/L Co.. The effect of electrolyte composition, current density, temperature, solution pH and presence of buffers such as H3BO3 and (NH4)2SO4 on Co content of the binary alloy has been investigated. In particular, current densities ranging from 180 to 400 A/m2 and temperatures ranging from 27 to 60°C were tested. The composition of Ni-Co alloys may be diversified through the selection of process parameters. The experiments show that the highest cobalt content of the alloy is reached by using a buffer free electrolyte without solution pH control. Though, in these conditions, the most homogeneous, fine and regular deposit morphology is obtained, energy requirements are the highest in tests lasting just two hours.

Jan 1, 2003

By K. Krishnapisharody

A mathematical model has been developed to predict the interface dynamics and droplet generation of the buoyant phase in a two-fluid system. The model employs the well-known SIMPLE algorithm for obtaining flow fields and the Volume of Fluid (VOF) method, for interface tracking. The implementation of the model in water-oil systems, where the oil layer is placed above a recirculating water bath, is discussed. The evolution of the water-oil interface leading to the formation of oil droplets is computed realistically.

Jan 1, 2008

By H. J. Thevik, A. K. Dahle

"A mathematical model that calculates the stress development in a coherent and stationary dendritic network due to interdendritic flow is proposed. The fluid flow is assumed to be related to the solidification shrinkage, and under the assumption of no porosity formation and unidirectional solidification, the shrinkage-induced flow within the mushy zone is calculated analytically. The interdendritic melt flow exerts a force on the solid network and an analytical expression for the stress build-up in the network is developed. Parameter studies illustrating the influence of cooling conditions, mushy zone length, dendrite coherency, fraction solid, volume fraction of eutectic, and solidification shrinkage upon the stress development within the solid network are presented. Comparing the magnitude of the calculated stresses to measurements of the strength in equiaxed mushy zones shows that it is possible for the stresses to exceed the strength, thereby resulting in reorientation or collapse of the dendritic network.IntroductionInterdendritic fluid flow is at present regarded as a very important mechanism for feeding of shrinkage during solidification of metal alloys. Solidification of many alloys is often characterised by heterogeneous nucleation of the primary phase on substrates in the melt with subsequent evolution of equiaxed dendrites. These equiaxed dendrites can initially grow freely, but impinge on each other and form a continuous dendritic network, ie. dendrite coherency, quite early in the solidification process. Measurements of the dendrite coherency point have shown that the dendritic network is established at solid fractions ranging between 0.1 and 0.5, and most often around about 0.2 [l]. Depending on the alloy composition this means that as much as 70 to 80% of the volumetric shrinkage has to be compensated by flow of liquid through the interdendritic network. Interdendritic flow occurs with a much larger resistance compared to free flow of the liquid and flow of a liquid with dispersed crystals. The pressure drop associated with the interdendritic flow increases rapidly with decreasing fraction ofliquid."

Jan 1, 1999

By Robert Vidal

A model of the homogeneous chemistry and transport processes within the separator of a chrome-alum electrowinning cell is introduced, discussed, and compared to experiment. The influence of diffusion, electromigration, and convection are included; it is found that convection was the dominant mode of transport for the experimental conditions. Simulation results explain experimental observations concerning an apparent disappearance of dichromate ions produced at the cell anode. The relation between potential drop across the diaphragm and the current and fluid flow is also illustrated. The model is used to recommend future experimental and theoretical work.

Jan 1, 1994

By Yong .. Jun Wu

Laminated ceramics have received widely scientific and commercial attention because their properties, such as mechanical properties and electrical properties, can be tailored by adjusting the structure, thickness and composition of the different layers. For example, ferroelectric Bi4Ti3O12 (BIT) which has a positive temperature coefficient of dielectric constant (,E) can be used to modify the negative tE of typical microwave dielectric ceramic BaNd2Ti4O12(BNT), However, BaNd2Ti4O12/Bi4TiO12/Bi4Ti3O12/BaNd2Ti4O12 (BNT/BIT/BNT) laminated ceramics could not be prepared by the general method because the optimal sintering temperature of BaNd2Ti4O12 ceramic (around 1350°C) was much higher than that of Bi4Ti3O12 ceramic (around 1100°C). In this research, a new method of spark plasma sintering (SPS) combined with post-sintering was successfully proposed to prepare BNT/BIT/BNT laminated ceramics. It was divided into three steps. In first step, the BaNd2Ti4O12 ceramics were prepared by conventional sintering method. In second step, the calcined and pre-pressed Bi4Ti3O12 powders were sandwiched between BaNd2Ti4O12 ceramic pellets and spark plasma sintered at 900°C for 10min to synthesize BNT/BIT/BNT composite ceramics. In the last step, a post-sintering was employed to reoxidize the partially reduced BNT/BIT/BNT composite ceramics. The results of scanning electron microscopy (SEM) and electron probe microanalysis (EPMA) showed that BNT layer and BIT layer were well bonded and no significant interfacial infiltration between them was observed. The sandwiched BNT/BIT/BNT ceramic with 10.7% BIT in volume has a dielectric constant of 92.85, a low dielectric loss of 01068 and a small temperature coefficient of dielectric constant of 35 ppm/°C at MHz.

Jan 1, 2003

By N. El-Kaddah, J. W. McKelliget

"A mathematical model for the analysis and design of hybrid plasma reactors for advanced materials synthesis is presented. The model is based upon a solution of the electromagnetic vector potential equation and is capable of predicting the two-dimensional velocity, temperature, and electromagnetic fields as well as the reaction kinetics inside the reactor for any axi-symmetric coil configuration. The model is used as a computer aided design tool for the design of hybrid plasma reactors consisting of a conventional DC torch augmented by an RF induction coil and it is demonstrated that the hybrid system possesses superior characteristics for materials synthesis over conventional DC or RF systems. The coupling between the RF and DC components is found to affect both the temperature field and the flow field and to have a significant effect on the reaction kinetics and on materials recovery. The model is used to study the thermal decomposition of silicon tetrachloride as a function of reactor design and operating parameters and it is demonstrated that through a CAD approach it is possible to significantly improve the operation of materials synthesis systems.IntroductionIn recent years there has been growing interest in the use of the inductively coupled plasma for chemical synthesis as a way of meeting the increasing demand for high quality, high performance materials for use in critical applications/l/. Although the basic feasibility of this approach has been demonstrated in the laboratory/2,3/ there still exists a number of operational problems that adversely affect system performance for some applications. In particular, the recirculation and back flow effects that arise from the electromagnetic forces in the plasma can result in the repulsion of the reactants from the hot plasma core and their subsequent deposition on the walls of the reactor. Another operational problem arises from the fact that the energy dissipated in the plasma has to compensate for the heat losses to the environment by conduction, convection, and radiation in order to maintain the ionization of the plasma and, hence, the stability of the plasma may be affected by the presence of the reactants and their products."

Jan 1, 1988

By Y. Y. Sheng

Plume flows created by gas injection into liquid metals have been studied extensively, however the dynamics of bubbles within the plume have not received adequate attention, particularly for large, irregular bubbles, characteristic of the processing of liquid metals. The present model uses a combined Eulerian-Lagrangian approach in which an estimated void fraction distribution is used to calculate the liquid flow field with a conventional Eulerian scheme. The trajectories of bubbles are then computed in a Lagrangian manner using the estimated flow field, and experimentally measured information on bubble drag coefficients', lateral migration due to lateral lift forces and interaction with turbulent eddies, and variation in bubble size due to break-up. Turbulence in the two-phase zone is modeled with a modified k-e model with extra source terms to account for the second phase which have been recently determined by the present authors. The computed void fraction and turbulent liquid flow field distributions are in good agreement with experimental measurements.

Jan 1, 1993

By Rune Gammelsmter

Turbulent chemically reacting flows are generally very complex, involving interactions of chemical, thermodynamic, and fluid mechanical processes. A combustion model based oh algebraic moment closure has been developed. The model is applicable for reaction rates where the chemical kinetics can vary from slow to fast. The effects of turbulence is taken into account by means of modifications to the well known k-e modelling procedure. The model is applied to an industrial combustion process. Calculation of furnace off-gas combustion from an aluminum reduction cell has been performed. The theoretical results agree well with experimental values.

Jan 1, 1992

By Y. Ide, K. Kishitake

It is expected that an Al-Cr-N composite nitride film may have a higher resistance to oxidation at elevated temperatures than the well-known Ti-Al-N films. The formation conditions of Al-Cr-N films by a de reactive sputtering method and their properties were studied in this study. The films characterized with respect to their high temperature properties such as chemical composition, crystal structure, microhardness, wear and· friction. The crystal structure of the Al-Cr-N films changed from hexagonal phase to cubic phase with an increase in Cr content in the films. The resistivity to thermal oxidation of the Al-Cr-N films is superior to that of usual TI-Al-N films. A half of the friction coefficient in the Al-Cr-N film was obtained comparing with that in the ordinary TI-Al-N film at room temperature and the wear rate of Al-Cr-N film was 2 order smaller than that of TI-Al-N film. The Al-Cr-N films show a small friction coefficient at 500°C and then they are recognized to have good tribological characteristics.

Jan 1, 2000

By G. A. Irons, D. Guo

"The average spout height and width produced by bottom gas injection in a water model of a steel ladle were measured with an image processing technique. It was revealed that the spout height could be described by a Gaussian curve. A combined SIMPLE -VOF model was developed to simulate the liquid surface and flow. The results showed that, though the model produced reasonable velocity distributions and free surface positions, the spout height due to the dynamic head of the rising liquid was substantially lower than observed, indicating that the bubble dynamics at the bath surface play an important role in spout height.IntroductionDue to the enormous importance of gas injection and stirring in metallurgical processes, there have been numerous publications on water and numerical modeling of such vessels. The free surface of the bath has received considerably less attention, despite its importance. At the free surface there are often important chemical phenomena occurring that require a good understanding of the fluid flow; these would include reoxidation of steel, metal splash and fume formation. Furthermore, to understand the details of slag-metal interactions such as slag entrainment, metal losses to slag and the transport phenomena associated with refining reactions, it is necessary to understand the plume and spout interactions first.There have been few experimental studies of the free surface of liquid in gas-injected ladles [1- 3], and even fewer on numerical modeling. Brimacombe and co-workers [1] studied the gas void fraction in the spout region, using a double-tip electrical resistance probe. This sensor cannot distinguish between gas in bubbles about to break and gas in the freeboard. Thus, it is a matter of judgement as to the position of the free surface. Schwerdtfeger and co-workers [2] used a single probe configuration with a wire and a counter electrode in the liquid, so that the height of the continuous liquid phase was unambiguously determined. Irons and co-workers [3] measured the spout height by ultrasonic and electrical capacitance techniques. These techniques were as reliable as the resistance techniques, but were restricted to low flow rates."

Jan 1, 2001

By Jr. Napolitano, Jr. Sanders

"Morphological evolution of a dendritic growth front in a binary alloy is simulated using a cellular automaton approach to establish the feasibility of modeling such growth with a local rule-based scheme. The motivation for this work is derived from the need to predict the development of solidification structures within real components of complex geometry, where significant constraint of the thermal and solutal fields may exist. Such cases present complex boundaries and large domain sizes, which may preclude the effective use of more conventional methods. In this work, a model is presented which couples a two-dimensional alternate-direction-implicit finite-difference diffusion solution with a cellular automaton growth algorithm to simulate morphological evolution in alloys solidifying under directional growth conditions. Temperature, composition, and interface curvature are incorporated into a local growth potential which is used by the automaton, allowing the interface to evolve. Alloy solidification is simulated over a range of experimental conditions, producing various structures. Issues addressed include morphological instability, primary spacing selection, interface curvature, microsegregation, and tip conditions.IntroductionThe development of dendritic structure plays an essential role in alloy solidification. Virtually every microstructural feature, within a cast alloy component, is related to the interface morphology present during solidification. Conventional solidification theory, describing dendrite tip kinetics and mushy zone phenomena, provides a means for estimating overall microstructural parameters for an alloy solidified under steady-state conditions. Microstructural prediction for actual components, which are finite in size and complex in geometry, requires a description of the evolution of the interface morphology under transient conditions and geometrical constraint and an understanding of how the structure propagates through the mold. Any useful simulation tool must be equipped to handle these circumstances within the limits of computational feasibility."

Jan 1, 1998

By Dorothée Proffit

Characterization of solids containing cyanides is carried out according to recommendations and standard guidelines. Most of these procedures are based on the analysis of leachates collected either on site or after leaching in the laboratory of samples. Unfortunately, these sole results are often insufficient to identify the source of the pollution. To provide 'a more complete characterization of polluted solids, optical and electron microscopy, XRD, Mossbauer spectroscopy, and transmission infrared spectroscopy were combined to analyze leachates and raw or ground samples. This combination of techniques allows the determination of the kind of cyanoferrate complexes are present in the solid state, different from insoluble Prussian Blue, since they do not have the same extraction' behavior. The use of all these techniques to characterize solid samples combined ,to the usual analysis of solutions gives a better understanding of ' the cyanide behavior.

Jan 1, 1998

By E. Gutierrez-Miravete

A computational method for the simulation of mold filling processes is described. The method is based on the representation of the flowing or deforming medium as a collection of mutually interacting parcels of material. Instantaneous positions of individual material parcels are calculated by numerical integration of the dynamic equations, subject to appropriate initial and boundary conditions. So far, the method has been used to produce qualitative simulations of some flowing and deforming systems encountered in mold filling technology, and our findings are summarized herein. In all cases, individual material particle motions can be followed in detail, allowing critical examination of potentially problematic mold design features.

Jan 1, 1992

By H. H. Law

Large amounts of waste material in the form of flue dust are generated in the operation of copper smelter furnaces. As a result of increasingly stringent disposal, it has become important to develop methods for treating such metallurgical wastes to extract metals and convert them into salable products. A two-step closed-loop hydrometallurgical process, has been developed: (1) extraction with sulfuric acid removes about 90% of zinc and decreases the dust volume by 50%; (2) extraction with hydrochloric acid dissolves the lead and further decrease the dust volume by 75%. A process scheme for generating salable products is proposed.

Jan 1, 1992

By J. Boltano

This paper discusses the study, design and implementation of the new gas handling system for the Caletones Smelter of Codelco-Chile. A discussion on design conditions for a future Sulphuric Acid Plant using Teniente Converter gases is also included. The old system which started to be modified in 1985 and relied on natural draft and used balloon flues, resulted in a limited gas handling capacity for operation under future process conditions. This system also caused excessive fugitive gases in the smelter working areas. The new system permits handling of process gases from the higher capacity Teniente Converters Installed in 1987-1989 improving the gas handling of the reverberatory furnaces and Peirce-Smith converters as well as the environmental conditions of the smelter. This system utilises improved converter gas hoods, evaporative cooling and electrostatic precipitators gas cleaning, and is based on natural draft.

Jan 1, 1992

By Douglas J. Harvey, Chi-Mou Ni

"This paper presents an analysis technique for the solidification of metal castings. This method, based on a modified finite difference scheme with an irregular mesh, is capable of dealing with the complex geometries of castings. The nonlinearities in material properties of specific heat and thermal conductivity, arising from the phase change during solidification, are accounted for in the step-by-step calculations. Two solidification problems are solved with this analysis technique and the calculated results compare satisfactorily with experimental data. IntroductionCasting process design engineers are often faced with the difficult problem of designing castings to be produced porosity-free. Since the solidification of metal is affected by many interacting variables such as the thermal conductivity, density, and specific heat of both the molten metal and the mold, it is easily seen why this is a difficult task.Typically, casting tooling design is an intuitive process which builds on past successful methods. After processing equipment is constructed, trial castings are made and examined for dimensions and integrity. Changes in the tooling are generally required to improve casting soundness or to reduce cycle time. In the permanent mold process, tooling is complex and difficult to alter after initial construction. The water-cooled steel molds are part of the complete automated system. Associated holding furnaces, pouring ladles, casting conveyers, and utility connections all make other than minor adjustments a costly and time consuming task. An analytical method for using the principles of heat transfer for predicting solidification patterns would be of great value in the permanent mold process by minimizing costly changes."

Jan 1, 1986

By Jyri Talja, Shaolong Chen, Hannu Mansikkaviita

"For optimum smelting results, proper treatment of the feed is needed to ensure favourable conditions for ignition characteristics, heat balance, mass balance with tolerable impurity levels, and overall process economics. Feed preparation consists of physical treatments before drying (blending), chemical treatments before drying, (roasting, if required), drying itself and physical treatments after drying (fractioning, if required).Effects of fluctuation on mineralogy and moisture should be minimized by blending the concentrates in a bedding plant prior to drying. As an alternative to drying, additional treatments such as roasting for impurity removal may be needed for part of the concentrate.Sustainability, energy efficiency, utilization of waste energy, low gas and dust emissions, product quality, availability and occupational exposure reduction are decisive criteria in drying today. These criteria are best met by the Kumera steam dryer, which has the best energy efficiency, zero CO2 emission, lowest operational and maintenance expenses, and superior availability and product quality.IntroductionFeed preparation plays a crucial role in having a smooth smelting operation and also the overall smelting economics in metal production. Therefore, it is of significant importance for all copper, nickel and lead smelter operations in which sulphide concentrates are fed to the primary smelting furnace. Generally speaking, the higher the metal content in the matte after primary smelting, the more important the feed preparation. This is of particular importance in the direct blister (DB) process for copper production and direct oxygen nickel (DON) for nickel production.Bedding is the first stage in feed preparation. This is very important for the sake of smoothing the mineralogical fluctuation in the feed for better smelting control. Its importance increases as the number of concentrates available for the feed mix decreases."

Jan 1, 2012