Search Documents

By Ruth F. Brinkley

This report is the 18th of a series of reports originally issued annually, and more recently bienially, to acquaint the public with the work of the Federal Bureau of Mines in explosives technology. Part I reviews briefly the overall activities during fiscal years 1957 and 1958.4/ Part II presents in abstract form the publications prepared by the Bureau that appeared during the period.5/

Jan 1, 1961

By Edgardo Orderique

Southern Perú Copper Corporation ha desarrollado un programa de reevaluación de las reservas para optimizar cada etapa del proceso y así llegar a las reservas mencionadas. En este sentido, el presente texto desarrolla el esquema de optimización de una secuencia anual de minado. El proyecto comprende la realización de de perforaciones en zonas llamadas geometalúrgicas, con el fin de realizar pruebas metalúrgicas y definir el comportamiento del mineral en la concentradora y lixiviación. También se incorpora el concepto de índice de solubilidad, parámetro que sirve para diferenciar adecuadamente un mineral económico para flotación del de lixiviación y finalmente, se optimiza la secuencia anual de minado y disposición de material en botadero. En consecuencia, es importante determinar el uso de software y hardware adecuado para planeamiento de minado, ya que depende de la magnitud de la mina como en el caso deCuajone.

Sep 13, 2001

By Morabito J, Harrop D. W

Uranium exploration was commenced in 1973 and carried out at a regional scale over a wide area of the northern part of the Camarvon Basin of Western Australia by Minatome Australia Pty Limited and their joint-venture partners. As a result, pervasive uranium mineralization has been found in the Cretaceous sandstones near Manyingee Hills in the Onslow Region, which were probably deposited in a near-shore, fluvia deltaic palaeo-environment.Mineralization is generally found in poorly sorted argillaceous sandstones and siltstones near redox fronts formed by oxidizing waters circulating in reduced sediments. The principal minerals found in the two Manyingee deposits delineated so far are coffinite, uraninite with associated pyrite in the reduced zones, and phosphuranylite, siderite and limonite in the oxidized zones. The presence of dissolved uranium in the superficial aquifers, of secondary uranium minerals as coatings on granitic rocks, and of recent uranium-bearing calcrete sediments, suggest that the whole Cretaceous-Precambrian system has been subjected to the formation ofroll-front type uranium deposits since the Cretaceous. Continuing exploration is locating additional uranium occurrences. The deposits outlined so far are being evaluated for their amenability to in situ leaching tests planned for 1982-1983.

Jan 1, 1981

By J. R. Thoenen, J. L. Vallely, M. C. Malamphy

"SUMMARYMagnetic and gravimetric surveys wore conducted over an area of ap¬proximately 1,400 square miles in the bauxite district of central Arkansas. The primary purpose of these surveys was to discover any possible buried and hitherto unknown syenite masses favorable for the occurrence of bauxite and to determine the approximate position of the buried flanks of the known syenite masses which might offer conditions favorable for the discovery of new ore bodies.Those surveys indicated that the various syenite outcrops were domes or bosses on a large batholith and that ether similar domes occurred on the batholith but did net outcrop.Drilling on the local geophysical anomalies proved the presence of 10 buried domes, but only 2 of them were found to project above the upper surface of the Midway clays, a requisite of conditions favorable for the occurrence of bauxite ore bodies. The geophysical data indicated the approximate configuration of the buried flanks of the known syenite coutcrops, and the portions of these flanks that project above the Midway have now been outlined more accurately by drilling.The geophysical surveys have produced evidence permitting the elimi¬nation of a large area as unfavorable for the occurrence of bauxite.Magnetic surveys extending along the Midway-Wilcox contact from Gurdon, in Clark County, on the southwest to Searcy, in White County, on the northwest have proved the improbability of the existence of other syenite masses similar to those found in Pulaski and Saline Counties. A detailed magnetic survey of the Magnet Cove area in Hot Spring County has proved that the syenite mass exposed in that locality is an isolated intrusion and entirely unrelated to those of Pulaski and Saline Counties. This syenite mass does not occur under conditions believed to be favorable for the occurrence of bauxite."

Feb 1, 1945

By D. M. Lane, J. M. Berkoe

Engineers and Owners share a common desire to build reliable, efficient plants on schedule at reasonable costs. This paper describes one tool that Bechtel finds can integrate these objectives by “putting innovation into practice”. Examples of such innovative engineering practice include the use of computational fluid dynamics (CFD) to determine efficient designs. This paper outlines several examples of CFD applications on actual Mining and Metals Projects from around the world. The focus here is to highlight the modeling objectives, analysis strategy, actual benefit obtained from the work, lessons learned to improve future efforts and the common mistakes that can obscure the correct or best results, despite impressive graphics. The tools are powerful, and the results are more powerful when applied with skilled and well-directed human effort and ingenuity.

Jan 1, 2000

By R. Bitmead, R Barker, A. Drake

The opencut coal mine is located about 50 km west of Brisbane, the capital city of Queensland in Australia and produces about 140 000 tonnes per annum of high grade steaming coal utilising a small team (ten) of personnel to mine remnants of the Aberdare and Bluff seams left by previous underground mining. This, in itself, is not remarkable except that one of the seams has commenced spontaneously cornbusting resulting in temperatures in excess of 55’C commonly being encountered with portions of the p’it being wreathed in steam. To extend mine life, the mine required a blasting system that would: . Safely blast in temperatures below 100°C . Significantly reduce overall unit costs . Not increase the current vibration impacts on nearby housing . Not increase flyrock.

Jan 1, 2002

By M. Kumral

The efficiency of an ore-processing unit depends on the consistency of the characteristics of raw material entering the plant. When the mined ore is highly variable in quality, the only way to ensure consistency is to homogenize the ore prior to feeding to the processing plant. The homogenization can generally be achieved by the bed blending operation. Given that the stockpiling and reclamation processes are very expensive, it is necessary to design the process in such a way as to minimize variabilities of specified properties of raw material. In this paper, for alternative stacking types, optimal stockpile geometry is found in three stages: First, stockpile input is simulated by sequential Gaussian simulation, and then the variance reduction ratios (VRR) as a criterion of stockpile efficiency are calculated for various stockpile geometry scenarios by a stockpile simulator written in FORTRAN. Second, multiple regression analysis is performed to model the VRR by the use of stockpile length, the number of layers and stacker speed as the independent variables. Finally, the model is an optimization problem. Decision variables are the stockpile length, the number of layers, stacker speed and stacking type. The genetic algorithms (GA) are used to minimize the VRR. The approach was demonstrated on data from an iron orebody. The problem was to reduce fluctuations of iron, silica, alumina and lime contents in the stockpile output. The results showed that the approach could be used for the bed blending design efficiently. Keywords: bed blending design, multiple regression analysis, genetic algorithms, iron ore, content fluctuation

Jan 1, 2006

By Almer E. C. van der Stoel

"Abstract This paper deals with assessing the bearing capacity of existing wood pile foundations. With a wide range of restoration projects being performed in the Netherlands, on many locations deep excavations need to be constructed next to existing, many times listed buildings. The building are founded on piles that are often centuries old, so a close evaluation of the remaining bearing capacity, combined with and assessment of the influence of the excavation is in place.After giving an introduction on Dutch pile foundations, a methodology is described to assess the bearing capacity. Aspects as physical foundation investigation, determination of the current bearing capacity and a calculation of the bearing capacity in the new situation are discussed. The results of both analytical and Plaxis calculations are outlined, focussing on how to practically use this approach in renovation projects. Finally, cases studies of the successful application of this approach in major renovation projects in Amsterdam, such as the Conservatorium Hotel and the New Rijksmuseum are used to illustrate the successful application of this approach.A Short Dutch Pile Foundation History (based on Van der Stoel, 2001)The first houses built in Amsterdam, in the 12th century, were very light constructions of timber without foundations. Because of the soft peat layers found in Amsterdam, the houses there suffered from damage due to settlement. In the 13th century, castles and churches were increasingly built of bricks, which made it necessary to provide support for bigger loads. Under the wall of the construction a trench was dug, and this was filled on either side by alder fascines. Between the fascines small wood piles were driven (by hand) on which another series of fascines was put. On top of this construction, were placed oak slabs on which the bricks were then laid. From that moment on, a problem was caused by the decay of wood foundation elements in the humid soil. In 1503 a law was introduced forbidding building foundations on public streets without permission of the Building Inspection (to keep the fronts of the buildings in a straight line). In 1528 a law requiring permission from the local authorities for all building activities replaced this law. In this period developments started which led to the use of the type of foundation that can be considered the mother of the current “typical” Dutch pile foundation. The piles used in this period were shaft- bearing piles about 5 to 7 meters long. The mostly pine piles were driven between oak beams, which were placed on either sides of a trench, after which other oak beams were laid across at regular spaces: the so called “pile bent” pile foundation (Figure 1)."

Jan 1, 2014

By Bauduin C. Besix

The Eurocode 7 "Geotechnical Design" is based on "Limit State Design", tackling the uncertainties as much as possible at their source through: - selection of characteristic values of variables (loads, soil properties, pile resistance,...); - partial factors applied on the characteristic values; - model factors to account explicitly for uncertainties of the calculation rule if necessary. Eurocode 7 will propose three "design approaches". The selection of one of them will be by National Determination. For pile design, the approaches are: - approach 1 is a "material factoring approach" at load side and a "resistance factoring approach" at resistance side. The structural and geotechnical design are checked for both of two separate sets of partial factors. - approach 2 is a "load and resistance factoring approach" and is in several aspects close to a deterministic approach. The design is checked for one set of partial factors. - approach 3 is a material factoring approach, at load as well as at resistance side. The design is checked for one set of factors. The aim of this paper is to introduce to the design of pile foundations based on pile load tests and on ground test results (semi-empirical and analytical methods) in the frame-work of the three design approaches. Detailed attention is devoted to: - the selection of the characteristic value of the pile resistance, accounting for spatial variability and stiffness of the structure; - the reliability of the prediction of the pile resistance using analytical or semi-empirical methods which may be accounted for through a "model factor". The results of a large test campaign on screw piles in OC Clay and a calculation example illustrate the proposed procedure when calculation rules using CPT results are used.

Jan 1, 2002

By Jim Frazier

Tradition has often dictated low design load stresses on piles. Such traditions often developed prior to modern static or dynamic pile testing methods and perhaps result from a few limiting situations. These low stress limits were then broadly applied, even in cases where the piles could carry substantially higher loads. With sufficient testing to prove the design, higher design loads may present significant overall savings to the project owner. The cost of the testing then becomes an insignificant cost compared to the potentially great benefit of increased pile loadings. To confirm higher load possibilities for driven piles, the pile is tested either statically or dynamically. Further savings and increased testing efficiency result from remote dynamic pile testing. This paper presents a project where design stresses were considerably increased as a result of additional testing and use of remote dynamic pile testing equipment.

Jan 1, 2002

By Fisher N. I

Disequilibrium ratios (U3O8/eU3O8), which assess the degree to which gamma activity represents the uranium content of a sample, have been measured on a representative set of samples from the ore zone of a carnotite ranium deposit located at Yeelirrie, Western Australia. A statistical analysis has been performed to investigate the dependence of the ratios on lithology and on the location of the sample in the orebody. The analysis indicates that dependence on lithology and on position across the orebody is negligible. Samples from the western end of the orebody and those from below the water table level tend to have slightly lower ratios than samples from other positions, although these trends are small compared with a large random variation in the data. The large random variation could result from some redistribution of the daughter isotopes of uranium within the orebody. On the basis of the results from all the samples, the estimated deficiency of uranium relative to radium in the ore zone of the deposit is 11 per cent.

Jan 1, 1980

By F. T. Cawood, M. A. Jooste

This paper describes the survey monitoring processes at Venetia, which are discussed under visual inspections, ad hoc investigations, system monitoring and slope stability radar monitoring. This is followed by a description of the main survey monitoring methods. The next section briefly states typical problems, i.e. the atmospheric corrections required to adjust total station distances, maintenance of the system and management of the monitoring process. The paper ends with some important lessons that could be applied to similar monitoring programmes. These lessons are firstly, communication is most important, process a vital part of the system, a champion must take responsibility for the programme and system planning ensures that the monitoring results are needs driven.

Jan 1, 2006

To date Iron Monarch is the most important Australian source of iron ore and since HH5 has produced about 84 million tons of direct shipping ore containing 62 per cent iron and 3 per cent manganese.Previous geological work, mainly by Rudd, Edwards and Miles is reviewed and the results of later exploration by quarrying and drilling are discussed and modified interpretations of both stratigraphy and structure are advanced. Renewed study of the mineralogy of the iron ores is advocated.The Iron Monarch orebody lies on the up-thrown side of a major transcurrent fault that truncates it on its northern boundary. The nearby Iron Knob orebody is believed to occupy a horizon that is some thousand feet stratigraphically above Iron Monarch.The origin of the ore cannot be explained by any simple theory; development probably took place over a long period of time from Lower Palaeozoic to Tertiary.INTRODUCTIONIron Monarch orebody has supplied the Australian iron and steel industry with the greater part of its ironstone requirements since the establishment of the Newcastle steelworks in 1915. Annual production of direct-shipping ore has exceeded three million tons but declined slightly after 1956 when Iron Prince was brought into production. Total production of ore from Iron Monarch to the end of 1962 is about 84,000,000 long tons containing some 55,000,000 tons of metal.The deposit (Lat. 32°44'30"S : Long. 137°08'30"E) is 34 miles north-west of Whyalla, on the western shore of Spencer Gulf. A 42 in. gauge railway connects Iron Monarch and its associated small town of Iron Knob with Whyalla (Fig. 1).For the purpose of this paper Iron Monarch includes Iron Knob and the intervening jaspilite hill known as Substation Ridge, and the description of the general geology necessarily 'Assistant Chief Geologist, The Broken Hill Proprietary Co. Ltd.This paper was presented at the Annual Conference of The Institute, 14-24th August 1968.

Jan 1, 1964

By Earl R. Maize

Epoxy and polyester-type resins were injected into coal-mine roof strata of the thick Freeport coal seam in Allegheny County, Pa., at test sites in roof that had been exposed several weeks, in newly exposed roof, and in strata over solid coal. Test results indicate that the method of strengthening bituminous-coal-mine roof by injecting a bonding material into the roof strata can be developed into a safe, efficient support system. If roof bonding will become a standardized method of roof support and reinforcement or if it can be effective when used with other types of roof support can be determined only by extensive experimentation in various coal beds. Observations and conclusions are shown at the end of this report.

Jan 1, 1959

By M. J. Blattman

Upon completion of an underground mine design, the planning engineer is faced with a surprisingly complex problem, “What development and mining sequence should be implemented so as to maximize the return on investment?” The problem relates to the scheduling of development headings to access stope production areas in such a way that the most money is made as quickly as possible for as long as possible. The total dollar value of the stopes, the average grade, the total tonnage, nor even the profit margin do not accurately give an indication of the “proper” mining sequence on their own. This paper will outline a method being developed by the author that can create a sequence of events that maximizes the net present value (NPV) of a given development and production design using information already being generated during the design process.

Jan 1, 2003

By John P. Turner

The behavior of tieback retaining walls depends on many factors, including soil properties, groundwater conditions, construction sequence, spacing and stiffness of tiebacks and soldier piles, tieback loads, and others. The primary design considerations for tieback walls are 1) adequate stability and 2) limiting wall movements. Traditional design methods rely on apparent earth pressure diagrams and experience to predict the forces which must be supported by the tiebacks to provide adequate stability. The required soil properties depend upon whether the soil is sand, soft clay, or stiff clay. Design to limit wall movements is more difficult and the usual approach is to design the wall with an adequate factor of safety for stability and then evaluate wall movements during construction through the use of load tests on individual tiebacks and monitoring of wall movements by optical surveying, slope indicators, and extensometers. If excessive movements are likely to occur, it is often not known until construction is well underway. This approach is reflected in the fact that few tieback walls fail due to a lack of adequate stability, while most litigation involving tieback wall performance is related to excessive movements. Much progress has been made in recent years in methods for predicting the movement of all types of insitu retaining walls (Clough et al. 1989, Clough and O'Rourke 1990). These methods are based upon both experience and analytical methods. This paper reviews the methods currently available for evaluating both the stability and movements of tieback retaining walls. Case histories involving excavations constructed in the downtown Seattle area are used to evaluate the applicability of the available methods to Seattle conditions and to illustrate the importance of soil behavior in tieback wall performance.

Jan 1, 1990

By Arthur A. F, MacKenzie I. H

Copper in zinc/lead sinter charged to the Imperial Smelting Furnace operated by Sulphide Corporation Pty Limited at Cockle Creek, New South Wales, concentrates in a complex lead dross which forms as the bullion is cooled to around 400°C. The 0.35 mm portion of this dross, containing approximatelY 67 per cent of the total copper, is treated via a hydrometallurgical route to produce 5000 tonne/yr of CuSO4 5H2O crystal.Around 3000 tonne/yr of copper-lead dross containing 49 per cent copper is leached at 55°C in continuous leach reactors with ammoniacal ammonium carbonate leach liquors to convert copper to soluble copper amine complexes. Leach ettlciencies of 80-85 per cent are obtained. Leach residues are repulped with ammoniacal liquid diluents from the plant and heated in a four stage steam distillation unit to reduce ammonia levels to between 0.5 and 1.0 g/Iitre. The resultant slurry is directed to an effluent treatment plant for final treatment, and separation and return of solids to the sinter plant.Copper is extracted from leach liquor by solvent extraction techniques based on the use of L1X 54 diluted 3:1 with Shellsol 2046 to give a nominal copper loading of 30 g/litre. The loaded organic is contacted with a sulfuric acid solution of pH 5 to remove the bulk of ammonia and zinc, then stripped at 55°C with a 60 g/Iitre H2SO4 95 g/Iitre copper solution to yield a 15 g/Iitre H2SO4 125 g/Iitre copper solution.This liquor is fed to an adiabatic vacuum crvstalliser operating at 35°C and 5 kPa vacuum where crystals of CuSO4 5H2O are formed. Crystals are separated from mother liquor and washed in a two stage pusher centrifuge, then dried in a hot air rotary drier. The crystal product obtained is of a high chemical purity and readily conforms to both Australian and overseas standards.

Jan 1, 1983

By Mohamed A. Younis, Paul J. Headland, Paul H. Madsen, Vojtech Gall

INTRODUCTION A 100 ft long, 20 ft high and 18 ft wide NATM tunnel was excavated through grouted clean sands beneath a busy city street, including a variety of existing utility lines. The new tunnel associated with a hospital expansion will serve as a pedestrian tunnel connecting a parking structure with a new hospital facility. Tunnel construction started on December 15, 2005 when drilling for the grouting program started and was completed on May 26, 2006 when the tunnel final lining was completed. The tunnel was constructed by Kiewit Construction Company as a tunnel subcontractor to The Christman Company who is constructing the hospital facility for Spectrum Health in Grand Rapids, Michigan. URS was the project designer. GallZeidler Consultants, LLC were the contractor’s NATM consultant. PROJECT DESCRIPTION The Michigan Street Pedestrian Tunnel is a component of the Michigan Street Development located along the north side of Michigan Street NE between Coit Avenue NE and North Division Avenue in the downtown area of the Grand Rapids, Michigan. The Michigan Street Development includes a parking deck and four new towers to be constructed over the proposed parking deck. The tower planned furthest east is being developed by Spectrum Health as the Lemmen-Holton Cancer Pavillion. The purpose of the pedestrian tunnel is to connect the proposed Lemmen-Holton Cancer Pavillion with the future Spectrum building to be located on the south side of Michigan Street NE. The southern end of the tunnel was constructed with a bulkhead until the future Spectrum building is constructed at which time interconnection will be required. The tunnel site plan and profile are shown in Figure 1, Site Plan, and Figure 2, Tunnel Profile. Several challenges were faced during the design and construction of the Michigan Street Pedestrian Tunnel. These challenges included compressed design and construction schedule, maintenance of traffic and protection of old underground utilities. The tunnel was being constructed as part of the Michigan Street Development and coordination with other concurrent construction activities was required. The tunnel was constructed within a specified window of time to allow other associated construction activities to take place without compromising the overall project schedule. The design started in June 2005 and construction was completed by June 2006.

Jan 1, 2007

Determination of Flotation Kinetics of Coal Grain Types in a Pilot Scale Jameson Cell using Coal Grain Analysis Method

Sep 13, 2010

By Da-Qiang Cang, Qingde Wang, Wei Wang, Wen-Bin Dai, Min Guo, Yu Li

Utilization of both slag and its heat for hot slag is a great challenge for iron and steel industry. Many methods of hot slag modification for directly converting hot slag into value-added materials were researched in recent years, and waste heat of hot slag could thereby be transformed into inner energy or chemical energy of the materials. In this paper, an experiment of converting hot slag directly into glass ceramics by hot slag modification method was conducted. A cooled modifiers mainly composed of fly ash were firstly heated though a cyclone furnace and then fell into a molten bath to mix with hot steel slag. Half of hot slag was used as raw materials and accordingly about half energy consumption, about 5MJ/kg for melting raw materials was saved in the process compared with that of traditional producing method. Frit quenched from the modified hot slag had a higher basicity of 0.6-0.7 than traditional frits in order to reduce the needed amount of cold modifiers and accordingly utilize more hot slag and its waste heat. Glass ceramics were further prepared from the frit and a heat treatment of one-stage method is more suiter to such frit than that of two-stage method. The glass-ceramics with basicity of 0.6 and heat-treated by one stage method had the best performance with bending strength of 146.46 MPa, Vickers hardness of 6.79 GPa, water absorption rate of below 2% and shrinkage rate of around 10%.

Jan 1, 2015