Search Documents

By R. C. Good

Slag control for any kind of steel, rimming, straight carbon or alloy, should start with the charge and be developed well in advance of the tap because its composition, viscosity and temperature will unquestionably govern the physical and chemical properties of the steel when tapped. In the majority of plants producing alloy steels, primary consideration is given to the chemical specifications; physical characteristics usually occupy secondary place in the melter's mind. Recently, however, buyers have indicated limits of machinability, hardenability, grain size and, of course, always wanted steel free from foreign nonmetallic inclusions. It is these latter specifications that require the attention of the operator to the slag and its control. The slag must act as a vehicle for oxidized elements originating from the metallic portion of the charge; it should hold the oxides of phosphorus, silicon, manganese, iron and chromium that come into contact with it either before or after the refining and finishing stage of the heat. It must be used as a transferring medium of oxygen from the atmosphere or oxide additions to the metal and should permit a free escape of gas generated within the charge. Finally, the slag is the principal controlling factor in regulating the rate of oxidation which in turn eventually determines the quality of the steel as measured for the various characteristics mentioned above. With pig iron of uniform composition, the iron oxide in the slag increases as the limestone is increased but with the same addition of stone in every heat, the iron oxide decreases as the silicon is increased in the charge, and vice versa.

Jan 1, 1935

By Leonard Larson

DURING several years immediately preceding the adoption of wet-charge smelting at McGill, various necessary conditions affecting this procedure, such as plant rearrangement and the metallurgical nature of the concentrate produced at the concentrator, were fully considered. Wet-charge smelting is not altogether novel to the recently reconstructed smelter at McGill. A number of years prior to this improvement, when flotation methods were initiated at the concentrator, large tonnages of wet and (at that time) sticky flotation concentrate were charged directly into the reverberatory furnaces, because of the difficulty in handling the entire tonnage in the roasters. The plant had excess reverberatory units and this surplus furnace capacity was utilized to smelt raw flotation concentrate. During the years 1927 and 1928, a number of actual operating furnace test runs were made to determine in principle the feasibility of wet-smelting operation. Results were encouraging, and in November 1932 the roasting plant was shut down. For some time thereafter the wet feed was delivered directly to the reverberatory side-charging calcine hoppers already in place. Feeding the wet material through the old calcine hoppers and charge holes into the furnace involved considerable labor, but under the conditions existing at that time it was desirable to continue wet smelting even under the handicap of this laborious procedure. The smelting plant during this period was on a curtailed production basis, operating only about 15 days per month. The alternate starting up and shutting down of the roasting plant presented a difficult problem and charging the wet material directly to the furnace entirely eliminated this difficulty. The roasting plant was never operated thereafter. EARLY PROCEDURE Fig. 1 shows the general layout of the smelting plant before the smelter was remodeled. Under this arrangement, all concentrates and fluxes except converter flux were delivered in cars to wooden storage bins, which paralleled the roaster building. The material to be roasted was dis-

Jan 1, 1938

By Eugene J. Schreiber, F. Newton Parks

Booz-Allen & Hamilton management consultants has recently completed a comprehensive study of Brazil's minerals and metals sectors for 40 leading international and Brazilian companies. The 220-page study describes the activities and Investments under way in 25 key commodities and assesses the current state of Brazil's economy, the impact on domestic minerals and metals industries, and government minerals policies.

Jan 12, 1977

By N. G. W. Cook

At present, tunnels can be driven in rock by either of two essentially different techniques, in one of which rock-breaking is accomplished by drilling and blasting and in the other by mechanical loading. The methods based on these techniques are comparable in terms of the rates at which tunnels may be advanced, although they differ widely in their range of applicability to different types of rock and lengths of tunnel. The method based on drilling and blasting has reached a high degree of development. It is applicable to even the hardest rocks and rates of advance in excess of 50 ft per day (fpd) are attainable. The main disadvantages of this method are that it involves a sequence of operations punctuated by blasting and that it is relatively uncontrolled, resulting in overbreaking the tunnel profile and damage to the surrounding rock. However, its flexibility, mobility, and low capital cost constitute real advantages in many situations, such as those involving short lengths of tunnel or low rates of advance. Tunneling machines based on mechanical breaking of the rock are a more recent development. They offer a continuous and controlled means of tunneling capable of rates of advance in excess of 100 fpd under favorable conditions. However, these machines weigh many tens of tons and consume several hundred horsepower, so that they are costly and lack mobility. At present, their applicability is limited to long tunnels in relatively soft rock where the high rates of advance and tunnel quality can offset their onerous capital cost. Many situations exist in which the superior quality of a machined tunnel and freedom from blasting would be real advantages, but where the rock is either too hard for existing machines or the length of the tunnel does not justify their capital cost: What are the possibilities of developing cheaper, more flexible, and mobile tunneling machines? Most existing tunneling machines fragment all the rock at the tunnel face to facilitate its disposal. If a machine were used to cut only the profile of a tunnel as one of a sequence of operations, it would be required to break

Jan 1, 1970

By W. N. Lacey, D. F. Botkin, B. H. Sage

JOULE-THOMSON coefficients for two natural gases were determined at pressures up to 600 lb. per sq. in. throughout the temperature interval between 70° and 310°F. From these primary data and available information relating to the isobaric heat capacities of the components at infinite volume, the heat capacities of these gases were computed throughout the above-mentioned range of pressures and temperatures. The enthalpies of the gases were computed as a function of state and the results compared with values obtained by several methods of prediction currently available. The results are presented in graphical and tabular form.

Jan 1, 1942

By d&apos, C. McCoul, C. Antonio, R. Krohn

MOST of the commercial colored gold alloys for jewelry applications are based on the Au-Ag-Cu-Zn system. Although work has been done on the constitution of the Au-Ag-Cu system.'-4 there are no reports in the literature on the effects of zinc additions in these alloys. We have metallographically determined the a =al + a2 transformation temperatures in 91/2- and 131/2-karat alloys in which varying amounts of zinc have been substituted for copper and silver. Samples were cast in the form of 1/2-in. round bars

Jan 1, 1970

By S. C. Sun

Most previous work on sedimentation of coal 1 and mineral 2-3 suspensions has been conducted in graduated 1-liter glass cylinders of 6-cm diam. With this type of large container it is often difficult to see through the suspension and tedious to perform a large number of tests. Furthermore, the heavy glass walls and the graduation lines of glass cylinders cause internal and stray reflections, respectively. To obviate these difficulties, an Atlab Emulsion Viewer from Arthur H. Thomas Co. was adopted as an alternative apparatus. Equipment: The viewer," shown in Fig. 1, consists of: 1) a stainless steel frame rack holding 21 flat-bottom Nessler tubes or an ungraduated replica 1.64 cm ID and 1.80 cm OD, 2) a movable masked 150-w lumaline lamp behind the tubes, and 3) a scaled glass panel with 100 vertical divisions in front of the tubes. The tubes are snugly held by springs in slots formed by spacer bars, which also serve as shields to eliminate stray light. The lumaline lamp is mounted behind a slit in a movable housing so that it can be positioned behind the suspension to be examined. The lowest or 100-divi-sion line on the front glass plate is leveled with the upper side of the bottom of all tubes. The scaled portion of each tube, roughly 19 cm high and 40 ml in volume, is used to study coal and mineral suspensions. Procedure: The following procedure was used in many tests. A 1.6-gm sample of dry coal was mixed with 16 ml of distilled water in an ordinary test tube and allowed to stand for three days, with occasional shaking to insure thorough wetting of all particles. The slurry was transferred to a Nessler tube and diluted to 32 ml. The pH regulator and flocculating reagent were added, and the slurry was diluted to reach the uppermost or zero-division line. The tube was immediately stoppered and inverted downward and up again ten times during a period of 35 to 40 sec. The lumaline lamp was turned on during the inversion period. After inversion the tube was quickly returned to the viewer rack. The time elapsed for each 10-division drop of the demarcation line between solid and liquid was recorded by stopwatch until the 80-division line was reached in the zone of compression. Additional readings were taken at 15, 30, and 60 min after settling began. The clarity of the supernatent liquid was observed also. As the settling rate became considerably slower at the 75-division line, it was convenient at this time to start the next test in a separate Nessler tube. This was continued until the suspensions in any number of the 21 tubes were tested. An attempt was made to correlate the experimental results between the Nessler tube and a 1-liter glass cylinder. Table I shows that coal particles settle much faster in the cylinder than in the tube, which has a large wall effect.' The correction factor for the tube impedance is 1.662 2 0.145 at the 40-division line in the hindered settling zone, and 1.614 & 0.139 at the 75-division line in the compression zone. This rough correlation was established by dividing the pulp height of each container into 100 divisions and comparing the settling rates of the two containers at the same divisions. Tests were also performed to determine the accuracy of the viewer. The results, not presented, showed that error was within 10 pct.

Jan 1, 1960

By E. V. Given

Designing a tailing dam is a major step toward fully integrated mill operation. In the case of large concentrators considerable planning is necessary, and the site of the tailing disposal area may very well dictate the location of the concentrator itself. Before a suitable location can be selected several pertinent factors should be investigated: estimated life expectancy of the mine and, if possible, approximate total tonnage; knowledge of daily mill capacity; and the possibility of future mill expansion. In addition, the area should be able to store tailing for many years and, from a cost and maintenance stand- point, gravity flow will probably be desired.

Jan 7, 1959

By W. R. Boehme

The laboratory test work compares various 6 x 16 mesh activated coconut carbons using a gold standard solution of 4 ppm dissolved in sodium cyanide. The carbon adsorption rate and maximum loading are measured for different feed solution ionic contaminates: silver, copper, thiocyanate, and ferrocyanide. Conclusions are drawn that among the activated coconut carbons tested, maximum loading and the effects of specific ions varied significantly. The work presented can be applied to 6 x 16 mesh carbon selection tests and specific ion monitoring for industrial carbon adsorption systems.

Jan 1, 1984

In accordance with the usual custom, manuscripts to be presented at the next meeting of the Institute must be in the hands of the, Secretary before July 1, 1917. Manuscripts to be properly distributed in advance of the meeting must be in the hands of the Secretary before June 1, 1917. At the last meeting of the Institute 45 papers were presented, and 42 of them were actively discussed. This experience makes us believe that advance distribution is the best possible means of getting a good discussion of papers and of securing for them the interest of the members of the profession. It will be impossible, however, to give the papers proper distribution if they bare not received before June 1, 1917.

Jan 4, 1917

By Joseph M. Jacisin

Fatigue tests were conducted on 2017-T4 alumium in alloy in an u1lrcthig.h vacuum of 2 x 10-lo Torr and in air. The vatio of vacuum-to-air faligue life for this ~malerial varied Jrom 3.5:1 at a strain of 2.5 X 1O-3 ill. pegr in. to 8:l at a strum of 3.3 x X ill. per 171. Sotlze pvelivtlinary data were also obtained on the faligue life of the alumirnum alloy in a dvy-nitrogen atmosphere. A dark deposit observed on the fracture surfaces of the aiv-tested specimens was identified as oxides of tr~angarzese and magnesium This observalion, and the close correlalion betaveen results obtained in vaCuum and dry-nitrogen environtments, tend to confirm that air stvongly influences the fatigue mechanism by a covrosion process. THE fatigue life of certain metals is known to increase when the atmospheric pressure is reduced. Gough and Sopwith1-2 postulated that this is due to a joint chemical and mechanical process operating in air at the surface of the metal with oxygen and water vapor playing significant roles. Wadsworth and Hutchings3 observed that aluminum is mainly affected by the presence of water vapor. Very little information is available on the fatigue properties of structural aluminum alloys in a vacuum environment. This report describes work performed on 2017-T4 aluminum alloy in an ultrahigh vacuum (2 x 10-loTorr) and in air. Some preliminary data are also presented on the fatigue life of the alloy in a dry-nitrogen environment. 1) EXPERIMENT 1.1) Test Material. The material tested was commerciaT 2017-T4 aluminum alloy which, in addition to aluminum, has an approximate composition of 4 pct Cu, 1 pct Fe, 0.8 pct Si, 0.5 pct Mg, 0.5 pct Mn, plus smaller amounts of other elements.* Some typical naturally age to a substantially stable condition. Specimens were then machined from these rods and ground to a No. 8 microfinish. In order to minimize variation in material characteristics, specimens were made from rods procured from the same lot. 1.2) Apparatus. The apparatus and test specimen used in the fatigue tests are shown in Fig. 1. The device utilized a single-cantilever beam with rotating-bending loading. Bending stress was applied to the fatigue test specimen by placing a spacer beneath the bearing support, thereby providing a constant deflec-

Jan 1, 1968

By William B. Plank

For the first time in four years the number of mineral engineering students in the 228 engineering colleges of the U. S. and Canada exceeds 10,000. According to figures just released by the American Society for Engineering Education, the current enrollment of all engineering students is 222,178. The total of 10,274 mineral engineering students, undergraduate and graduate, is a 4% pct increase over a year ago. Total engineering is 11 pct larger than last year, about the same as in 1949-50, and 24 pct above 1950-51.

Jan 4, 1955

By J. H. Frye, R. M. Treco

One of the chief hindrances to an understanding of the hardness of solid solutions is the sparsity of suitable hardness data. There is great need of a large body of hardness data obtained from many different alloys of high purity by identical testing methods and corrected to correspond to a single grain size. A considerable amount of such data has been obtained by means of the Meyer analysis on copper-rich and silver-rich solid solutions. There are enough of these data to permit comparison of numerous alloys at equal solute concentration in these two solvents, but only in a few cases is it possible to construct hardness-concentration curves for any given alloy. Therefore additional hardness work on most of these alloys is desirable. The primary solid solutions of silver with cadmium, indium, tin, or antimony as solute are of special interest, since all elements are from the same period of the periodic table and since, as shown previously,l the hardening effect of equal percentages of these solutes is proportional to the lattice expansion produced by them. This paper presents the relation between hardness and concentration in the silver-antimony system from very dilute to nearly saturated solutions of antimony in silver. Experimental Procedure Alloys were made from silver, 99.99 per cent pure, and antimony, 99.975 per cent pure. Silver and antimony were placed in graphite crucibles that had an ash content of less than 0.7 5 per cent. These metals were melted and allowed to solidify in a vacuum, which, after melting was corn- . plete, was usually equivalent to 3 mm. of mercury. A high-frequency furnace was used. The ingots so obtained were worked and annealed to lessen segregation and to control grain size. Annealing was done in evacuated and sealed glass tubes. Hardness measuremeuts on specimens from these ingots were by means of the Meyer analysis.394 Using a 4-mm. ball, impressions were made under seven loads from 25 to 400 kg. The diameter of impression made under each load was measured. This enabled calculation of the constants in the well-known formula of Meyer. L = adn where L = load, d = diameter of impression, a = a constant, n = a constant The Meyer hardness is defined as P = L/i(1/4pd2) or P = 4adn-2/p Meyer hardnesses corresponding to d = I and to d = 4 are of especial interest, since the first corresponds to comparatively slight 'plastic deformation and the second to the maximum plastic deformation producible by penetration of the ball. These

Jan 1, 1945

By Sabert Oglesby, Albert L. Thomas

Until recently, probably the best means of sampling airborne dusts has been the impinger method. Dust-laden air is drawn into a sampling tube, and the particulate matters separated from the air and collected in the liquid in the impinger. A sample of the suspension is prepared on a slide and counted through a projection microscope. This method is simple and reliable, but it does suffer drawbacks. Since the collected particles must be counted visually, results of the dust count are taken. This seriously impedes studying the effectiveness of dust inhibitors, such as water sprays, or making adjustments in equipment. Greatest disadvantage of all, however, is the tedious task of counting particles in the sample. With the growing desirability of taking more samples, the effort involved in making these counts is a real factor in the cost of dust control. Finally, it is generally recognized that impinger dust counts can be related to health hazard only for specific kinds of dust and under similar conditions. This is because the rather complex mechanism of dust damage depends so much on size distribution of the dust. Counts determined by impinger samples cover a limited size range that does not necessarily correlate with retention by the lungs and upper respiratory tract.

Jan 3, 1959

By Edward Perry

IN the exploration of a copper deposit by drilling, obvious advantages are to be gained from a distinction between primary and secondary ore.1 Perhaps the chief of these is the aid which such a distinction renders in determining where a given hole should stop. The copper assay, often a sufficient guide, cannot always be exclusively relied upon. Primary ores may extend downward indefinitely and may fluctuate in value independently of depth: if primary ores are consistently lean for a considerable vertical distance, there is little reason to expect that, still deeper, they will increase to the commercial grade; on the other hand, rich primary ores may persist uninterruptedly downward or may come in again below a lean interval. Secondary ores, however, have a comparatively limited vertical extent; in a large way enrichment decreases with depth and finally gives out. It follows then, that when a hole descends from profitable ore into ore of less than the commercial minimum, the practical significance of the situation depends upon whether this decrease results from a decrease in secondary enrichment or is a variation in primary content: if the copper of the ore passed through has been chiefly secondary, little is gained in the average case by extending the hole much below the point at which the commercial limit is reached; but, when copper is chiefly primary, due weight must be given to the possibility that, still deeper, the ore may again improve.

Jan 2, 1916

By Donald R. Mason, Daniel F. O’Kane

DIFFERENTIAL thermal analysis measurements have been used to determine the ZnTe-In2Te3 pseudo-binary phase diagram. Since ZnTe and In2Te3 are both semiconductors, any intermediate compounds formed in this system should also be semiconductors according to the rules delineated by Mooser and pearson.1 The compound ZnIn2Te4 was first reported by Hahn et a1.2 and it has subsequently been prepared and characterized electrically by several workers. A brief summary of this work has been presented by Mason and O'Kane3 who also report that the compound appeared to melt peritec-tically. The Zn-Te phase diagram has been investigated by Kulwicki4 who found that ZnTe has a melting point of 1290° + 2°C. The In-Te diagram published in Hansen' contains significant errors, and has been redetermined by Grochowski et al.6 However, both sources agree that the melting point of In2Te3 is 667°C, with the latter authors reporting the previously observed solid-solid transformation occurring at about 550°C. Hahn ef al.2 reported lattice-parameter values for the ZnTe-In2Te3 system. The 67 mole pct ZnTe-33 mole pct In2Te3 composition was the only

Jan 1, 1965

By Leonard Larson

DURING several years immediately preceding the adoption of wet-charge smelting at McGill, various necessary conditions affecting this procedure, such as plant rearrangement and the metallurgical nature of the concentrate produced at the concentrator, were fully considered. Wet-charge smelting is not altogether novel to the recently recon-structed smelter at McGill. A number of years prior to this improve-ment, when flotation methods were initiated at the concentrator, large tonnages of wet and (at that time) sticky flotation concentrate were charged directly into the reverberatory furnaces, because of the difficulty in handling the entire tonnage in the roasters. The plant had excess reverberatory units and this surplus furnace capacity was utilized to smelt raw flotation concentrate. During the years 1927 and 1928, a number of actual operating furnace test runs were made to determine in principle the feasibility of wet-smelt-ing operation. Results were encouraging, and in November 1932 the roasting plant was shut clown. For some time thereafter the wet feed was delivered directly to the reverberatory side-charging calcine hoppers already in place. Feeding the wet material through the old calcine hoppers and charge holes into the furnace involved considerable labor, but under the conditions existing at that time it was desirable to continue wet smelting even under the handicap of this laborious procedure. The smelting plant during this period was on a curtailed production basis, operating only about 15 days per month. The alternate starting up and shutting clown of the roasting plant presented a difficult problem and charging the wet material directly to the furnace entirely eliminated this difficulty. The roasting plant was never operated thereafter.

Jan 1, 1938

By N. E. Bonn

IT is well known that most of the materials entering into the manufacture of thermocouples are subject to variations in their thermoelectric characteristics, the chief causes of which are: differences in chemical composition; the previous .history, which includes mechanical working, ageing, oxidation, and contamination; and mode of use, such as depth of immersion, etc. In the case of a very extensively use thermoelement, the iron-constantan couple, neither iron nor constantan are absolutely uniform, and a number of checks are made during the process of manufacture. As both are subject to diversion from a standard value, neither, can be used for checking the other. It is, therefore, necessary to find a third metal against, which iron and constantan maybe checked. It was to find such a metal; that the present investigation was undertaken. To be a reliable, checking standard, the metal must possess a fairly high melting point? it must be obtainable in sufficient purity, and it must be uniform and constant with respect to its thermoelectric qualities. The choice is, as a result, limited to a few metals, such as copper, gold, and silver. Copper has the advantage of low cost, which makes it possible to use each wire only once and thus avoid any variations due to continued use, although previous investigators have found1 that continued use does not affect the calibration of a copper-constantan thermocouple. Copper also has the advantage of a large thermal electromotive force against constantan and would be desirable as a checking standard if it could be shown that it possessed the proper thermoelectric characteristics. The investigation, accordingly, resolved itself into three phases: the uniformity of commercial electrolytic copper, the effect of aging and method of annealing, and the calibration of the copper-constantan thermocouple.

Jan 9, 1919

J. S. UNGER,*Pittsburgh, Pit., (written discussion?).-From the subject of the paper it is natural to expect that the data presented must be results secured from an open-hearth furnace working under normal conditions, but such is not the case, as the conclusions are based on the results of laboratory tests, which do not approach service conditions. The early basic hearths were made of burnt lime, then followed burnt dolomite, bricks made of calcined dolomite and a 'binder, usually tar, and finally magnesite bricks covered with a layer of sintered magnesite. When this material became scarce, special dolomitic refractories were used. In the summary, it is claimed that magnesite low in lime, or of greatest purity, ranks first in the resistance to slaking and to corrosive slags. It is well known that neither pure lime nor magnesia has much value as a refractory. By the addition f fluxes, such as silica and iron oxide, lime is rendered inert to slaking in the same way as are the special dolomitic refractories. An example on a large scale is the ordinary basic open-hearth cinder, produced every clay, which does not slake. Pure magnesia, regardless of the lime content, is not any better fitted for a refractory than pure lime. The pure natural varieties, such as Grecian or Washington magnesites, must be burnt with sufficient silica and oxide of iron to produce a satisfactory material. Grain magnesite, either artificial or natural, is, not used in burning in a hearth in the state in which it is received. To make a satisfactory hearth, it must be made more impure by adding about 20 per cent. of basic open-hearth cinder, otherwise it will-not remain in place.

Jan 5, 1919

By C. P. Watson

It is perhaps significant that a few years ago the sessions held here were chiefly occupied with production. In the last two years these sessions have been concerned with production curtailment, unitization and conservation, notwithstanding that production in the United States in 1929 reached a total in excess of 1,000,000,000 barrels. A study of the leading producing units in the United States shows that Oklahoma, Texas and California in 1929 yielded 84 per cent. of the total production from 33.5 per cent. of the total number of producing wells. Production in the United States in 1929 showed an increase of 107,000,000 bbl. over the 1928 figures. This increase in itself perhaps is not enough to have caused the serious situation that is now confronting the industry. However, taking into account the gradual encroachment on the consumption of fuel oil through the greater utilization of natural gas, probably we have reached the point in the United States where prices will determine to a large extent,' in 1930, the amount that will be produced. In the states of Texas, Oklahoma and California, the most significant developmcnt of 1929 has been the desire of operators to reach some agreement to bring production more or less in control with the estimated demand. In November, production in California, particularly in the Santa Fe Springs field, was drastically cut to meet a certain requirement. Similarly, in Texas, the Yates field has been developed and has been producing under an agreement on the part of the operators; and more recently in Oklahoma City, serious efforts have been made to keep produetion in line with consumption. For the year 1930 we can see nothing in sight except drastic curtailment. This is a matter that I am sure is occupying the attention of all the leaders of the industry.

Jan 1, 1930