Search Documents

By M. van Swaay, C. E. Birchenall

A. S. lBrling (Johnson, Matthey & Co. Ltd., Laboratories)— Because of its initial emphasis upon the production of membranes by powder metallurgy and by normal casting and rolling techniques, this paper is of considerable interest to those concerned with the design and application of industrial diffusion units. As the subsequent performances of the three grades of palladium were not compared in detail, it can perhaps be concluded that specific permeabilities were very similar. A short table in which the absolute diffusion rates obtained by the Authors with their three grades of palladium were compared with those of other investigators18-25 would, however, have been of particular value in view of the very variable results obtained with this membrane material. The Authors state early in the paper that the permeability of the thoriated samples decreased in much the same way as that of the nonthoriated samples. Later, they emphasize that sintered palladium without thoria was very susceptible to poisoning and did not respond as well as the other materials to the decontamination treatment. These results, which suggest that sintered membranes are less effective than those produced by normal methods, have considerable industrial implications, and amplified experimental details would be very welcome. The results of the Authors differ in one important respect from those of other investigators. Thus, no "bleeding" was required to maintain a constant rate of diffusion, although Davis, Darling, and De Rosset found this to be necessary. Davisz3 found that "bleeding" was necessary even when the hydrogen had already been purified by diffusion through a palladium tube, and it would be of value to know the purity of the gas stream emerging from the purification train shown on Fig. 1 of the Authors' paper. The Authors show that diffusion rates varied according to the square root of the pressure difference providing that the palladium membrane was not contaminated in any way. This finding is in agreement with the results of those workers2,18,19,23,24 who diffused their hydrogen through the membrane into a partly or completely evacuated system.Those workers who did not find this square-root law dependence did not have a partial vacuum on the downstream-side of the membrane.'' The difference between the two experimental con- ditions appears to be significant, as the absolute diffusion rates per sq cm of diffusion area are lower when the square-root law dependence is not observed. While the effect could be attributable to poisoning of the membrane it is conceivable that a positive pressure on the downstream side of the membrane might influence the mechanism of diffusion. In view of the capricious behavior of palladium, factors of this type, which are likely to influence its industrial significance, should be carefully considered. M. van Swaay and C. E. Birchenall (authors' 9-eply) — Our Eq. 191 may be compared with several others for hydrogen diffusion in palladium: D = 5.95 x exp (-5770/1)' D = 3.55 x 10"3 exp (-5550/)' D = 4.3 x 10"3 exp (-5620/1')' Other values are given in the literature, but in many cases surface poisoning may have affected the results. No analysis was performed on the hydrogen gas stream after purification. It should be noted that the presence of liquid nitrogen traps near the heated membranes may have set up convection currents and provided the equivalent of "bleeding." The question of whether a partial vacuum existed on the downstream side of the membrane is not clear. Does it imply that there is something unique about the permeability measured near one atmosphere pressure? We do not believe that there is. When square root pressure dependence is not observed, diffusion rates are not measured. Is "absolute diffusion rate per sq. cm. of diffusion area" equivalent to permeability? The terminology is new to us. In any case we doubt very much that pressures of the order of several atmospheres can affect the mechanism of diffusion.

Jan 1, 1962

During the year 1915-16, the Mining Engineering Society of the, Massachusetts Institute of, Technology had five meetings, at which the following gentlemen addressed the society on the subjects Mentioned: Professor Richards-Memory and the Business World. Mr. Hutchinson-Mine Examinations. Mr. Packard-Mining Law, Necessity of Amendment. Mr. A. H. Rogers-Organization of Mining. Property. Mr. C. Hurter-Explosives. Mr. W. Macgregor-Organization of a Gold Mine and Mill. During the year 24 new members were admitted, making the present active membership 54. There was an average attendance of 34 members at the meetings. HAIG N. SOLAKIAN, Secretary, 1915-16. The Pick and Shovel Club, Case School of Applied Science, has elected the following officers for the current year: President, G: D. Welty, Secretary, C. E. David, Vice-President, E. G. Hollman, Historian, L. S. Kuehn, Treasurer, C. E. Althouse, Sergeant at-Arms, H. H. Smith.

Jan 2, 1917

ALBERT SAUVEUR, Chairman. A. A. STEVENSON, Vice-Chairman. HERBERT M. BOYLSTON, Secretary, Abbot Bldg., Cambridge, Mass. John Birkinbine, William Kelly, J. S. Unger, William H. Blauvelt, Charles Kirchhoff, Felix A. Vogel, James Gayley, Richard Moldenke, Leonard Waldo, Henry D. Hibbard, Joseph ANT. Richards, William R. Walker, Henry M. Howe, C. F. W. Rys, William R. Webster, Robert W. Hunt, E. Gybbon Spilsbury, Frederick W. Wood. J. E. Johnson, Jr., For the meeting of the Institute which is to be held in New York City, Oct. 16 and 17, 1913, the following program has been arranged: October 16, 1913, 10 A. M W. A. Forbes, Blast Furnace Gas Cleaning. W. H. Blauvelt, The Slagging Producer. Prof. F. Peter (Leoben, Austria), The Generation of Steam by Waste Heat from Furnaces. G. C. Stone, The Generation of Steam by Waste Heat from Regenerative Furnaces. W. R. Shinier, Over-Oxidation of Steel.

Jan 10, 1913

By E. C. Reed

Drilling activity in Nebraska continued to decline during 1944. Nine tests for oil and gas were completed during the year and four wells were drilling at the close of the year. Four wells were drilled in Richardson County, three in Hitchcock County and single wells were drilled or drilling in Butler, Gage, Holt, Nemaha and Scottsbluff Counties. Only one of the completions resulted in commercial pro- duction, the others being abandoned as dry holes. A number of stratigraphic test holes were drilled in the state by the Stanolind Oil and Gas Co. and the Sinclair-Prairie Oil Co., in Johnson, Otoe, Chase, Dundy and Garden Counties. No new fields were discovered during 1944 but the limits of the Barada field, Richardson County, was extended a short distance southward. Oil production continued to drop and about two thirds as much oil was produced in 1944 as in 1943.

Jan 1, 1945

POSITIONS VACANT A steel manufacturing company is desirous of securing an assistant superintendent for its plant. Experience in open-hearth plants and in rolling mills particularly desirable. No. 112. Opening as assistant superintendent of a non-ferrous smelting plant. Man with metallurgical experience preferred but chief essential is ability to handle men. No. 114. ENGINEERS AVAILABLE (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) Member, aged 41, mining engineer, manager or general superintendent, 20 years' experience, 10 years in Mexico, 5 years Western States, 5 years abroad. Guarantee results, fluent. Spanish, excellent references. New York interview. No. 282. Member, technical mining graduate, 10 years' experience, especially in design, erection, construction and purchase of power and mining equipment and supplies, desires position in purchasing department. Married, aged 32, employed at present, references furnished. No. 295.

Jan 7, 1916

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who called at Institute headquarters during the period July 10, 1916 to August 1, 1916: W. A. Barnes, San Francisco, Cal. W. J. Mead, Madison, Wis. W. L. Bell, Davenport, Fla. Charles Mentzel, San Pedro, N. M. James P. Clarke, Jr., Little Rock, Ark. H. H. Miller, New York, N. Y. R. A. Carhart, Mitchell, S. D. W. E. Pomeroy, El Paso, Tex. G. M. Colvocoresses, Humboldt, Ariz. M. K. Rodgers, Los Angeles, Cal W. E. Defty, Phoenix, Ariz. S. C. Rodgers, Guanajuato, Mex. Carl F. Dietz, Worcester, Mass. John M. Baker and Hamilton W. Baker have resigned as general manager and mine superintendent respectively of the Baker Mines Co., of Oregon. After Aug. 1, their address will be 43 Emerson St., Denver, Colo.

Jan 9, 1916

By John F. Abel

"The most conservative persons I ever met are college undergraduates." Woodrow Wilson said that in 1905. No one is saying anything like it today. Chaos on the campus was a cliche of the sixties. Since 1905, education has expanded in every direction. Many more people are being educated for much longer periods of time. The school-leaving age has risen from 14 years to 20 years, on an average. Many are in school until after their 25th birthday. On the surface this situation appears all to the good. Our technical society needs a massive yearly infusion of semitrained (or educated, if you prefer) new blood. The efficiency of our economy and our standard of living are tied to high individual productivity which can be achieved only with an educated work force. Our democratic institutions are said to be founded on an educated electorate.

Jan 1, 1970

By E. T. Turkdogan, J. H. Swisher

bi the fivst part of the paper results ave given on the rate of decarburization of Fe-C melts ln CO2-CO atmospheres at 1580°C. The rate -controlling step is believed to he that irvlloluing dissociation of curbotz dioxide on the suvfuce of the melt. 4 genevral reaction mechanistm is poslnlated jor gels-t11eta1 veactions oc-curit~g on the surface of iron coutcotamncited with chemi-sovbed osygesL. Oxygen the present work on decavbuvization of liquid iron and previous studies on the kinetics of nitrogen absorption and desorplion are discussed in terms of the postulated mechanism, ManY of the early studies of rate of decarburization of liquid steel were of an exploratory nature and laboratory exppriments carried out pertained to open-hearth or oxygen steelmaking processes. References to previous work on this subject may be found in a literature survey made by Ward. Using more sophisticated experimental techniques, several investigators have recently studied the kinetics of decarburization of molten Fe-C alloys in oxygen-bearing gases. For example, Baker et al2.' reported their findings on the rate of decarburization of liquid iron, levitated by an electromagnetic field, in carbon dioxide-carbon monoxide-helium atmospheres. In these levitation experiments the samples used were small in size, e.g., -0.6-cm-diam spheres weighing -0.7 g, and the rates were measured for decarburization from about 5 to 1 pct C at 1660°C. The rates obtained under their experimental conditions were considered to be controlled primarily by gaseous diffusion through the boundary layer at the surface of the levitated melt. Parlee and coworkers3 measured the rate of absorption of carbon monoxide in liquid iron. The rates were found to follow first-order reaction kinetics, yielding a reaction velocity or a mass transfer coefficient in the range 0.2 to 0.4 cm per min. The coefficient was found to decrease with increasing carbon content of the melt. These investigators attributed the observed rates to the transfer of carbon or oxygen through the diffusion boundary layer adjacent to the surface of the melt. In the work to be reported in this paper, an attempt has been made to study the kinetics of gas-metal surface reactions involved in the decarburization of liquid iron. EXPERIMENTAL The experiments consisted of melting 80-g samples from an Fe-1 pct C master alloy in an induction furnace and decarburizing in controlled CO2-CO mixtures at 1 atm pressure and 1580°C. The master alloy was prepared by adding graphite to electrolytic "Plastiron" melted in racuo. None of the impurities in the master alloy exceeded 0.005 pct. The reacting gases were dried by passage through columns of anhydrone; in addition, CO2 impurity in carbon monoxide was removed by passage through a column of ascarite. A schematic diagram of the apparatus is shown in Fig. 1. A 1.25-in.-diam recrys-tallized alumina crucible containing the sample was placed inside a 3-in.-diam quartz reaction tube, all of which was surrounded by an induction coil. A 450-kcps induction generator was used as the power source. Water-cooled brass flanges, which contained the gas inlet, gas exit, and sight port, were sealed to the top of the reaction tube with epoxy resin. The reacting gases were metered with capillary flowmeters and passed through a platinum wire-wound alumina preheating tube, 0.25 in. ID and 11 in. long. The gases were preheated to about 1300°C. A disappearing-filament optical pyrometer was used to measure the melt temperature. The pyrometer was initially calibrated against a Pt-6 pct Rh/Pt-30 pct Rh thermocouple. The temperature was controlled to within +10°C by manually adjusting the power input to the induction coil. In a typical experiment, an 80-g sample of the master alloy was melted in a CO2-CO atmosphere having pcO2/pco = 0.02 and flowing at 1 liter per min. A negligible amount of carbon was lost and no significant reduction of alumina from the crucible occurred during melting, e.g., 0.005 pct Al in the metal. After reaching the experimental temperature of 1580°C, the gas composition was changed to that desired for a particular series of decarburization experiments. The duration of the transient period for obtaining the desired gas composition at the surface of the melt was about 20 sec . The flow rate of the reacting gas was maintained at 1 liter per min. After a predetermined reaction time, the power to the furnace was turned off. During freezing, which took about 10 sec, the amount of gas evolution was not sufficient to result in a significant loss of carbon. The samples were analyzed for carbon by combustion and in a few cases they were analyzed for oxygen by the vacuum-fusion method. RESULTS A marked increase in the rate of decarburization of iron with increasing pcO2/pco ratio in the gas stream is demonstrated by the experimental results given in Figs. 2 and 3 for pco2/pco ratios from 0.033 to 4.0. In one series of experiments, denoted by filled triangles in Fig. 2, the reacting gas was diluted with argon (48 vol pct) resulting in a slower rate of decarburization. Samples from two series of experiments with pco2/pco = 0.033 and pco2/pco = 0.10 (with argon dilufion) were analyzed for oxygen. In these Samples the oxygen content increased with reaction time

Jan 1, 1968

By Franklin Allison

THE influence of cobalt and nickel on the properties of steel might be readily expected to be very similar. The two elements occupy close and somewhat unusual positions in the periodic table, their chemical behavior and compounds are so completely analogous and their various physical properties, including the ferro-magnetic characteristic, show such a remarkable correspondence, that there is no doubt of a strong resemblance existing between these two metals. However, the variety of, properties that are obtained from steel is due, largely to the fact that the element iron possesses allotropic forms. Alloying elements that affect these allotropic forms, or alter the nature of the allotropic changes, exert a profound influence on the resulting steel. In the case of nickel and cobalt, although these elements are very similar chemically and physically, it is found that they differ distinctly in their individual effects on the critical points of iron. Both nickel and cobalt form a series of homogeneous solid solutions with iron at temperatures above 1800° F. The difference in their behavior does not occur until changes begin to take place in the solid state below this temperature. An inspection of the respective thermal equilibrium diagrams at the lower temperatures makes the opposite effects of nickel and cobalt clearly evident.

Jan 3, 1927

A remarkable industrial renaissance is underway in the People's Republic of China (PRC), says USBM's Dr. K. P. Wang in his recently released 96-page report on "The People's Republic of China-A New Industrial Power with a Strong Mineral Base." Dr. Wang's summary of the current mineral position of the PRC includes many insights into its future potential and trade possibilities with the West.

Jan 2, 1976

By E. J. Haug, K. L. Clifford, K. L. Purdy

St. Joe’s Minerals Corp.’s Southeast Missouri Mining and Milling Division produces lead, zinc and copper sulfide concentrates at three of its operations. The Viburnum and Fletcher mills have been described in previous papers. The new Bushy Creek mill, dedicated in May of 1973, is an updated version of the Fletcher mill incorporating 8.5m3 (300 cu ft) lead and zinc

Jan 1, 1980

By R. E. Stewart

The major mining companies of the world all face the problems associated with investing in new mining ventures. In particular, investment in foreign countries - whether these are advanced or developing countries - requires careful consideration. A thorough analysis of all the possible risks must be undertaken, so that realistic decisions can be made. Some of the points to be considered are outlined in this paper.

Jan 1, 1977

By Karl D. Libsch, Modesto E. Erneta

Both battery design and environmental pressures are forcing the secondary lead industry to consider new and different processes. Trends in battery design are making normal decasing increasingly difficult. Lead in air, sulfur dioxides, and solid/liquid waste heavy metal restrictions are tightening. There is no clearly defined industry trend toward a given process, but it is clear that plants will be larger, less labor-intensive, and automated.

Jan 1, 1977

SECTION I Page Page Manuscript Closing Date, Febru- Forthcoming Meetings xxvii ary Meeting v . Library xxviii New York Section War Meeting on Membership xxxii Ferro-Alloys v Biographical Notices: Minutes of Meeting, Board of Robert Bell, by F. D. Adams. xlix Directors xvii H. J. Cantwell, by H. A. Members in Military Service xviii Wheeler 1 Personal xxiii Institute Committees Iii Employment xxv Officers and Directors Ix

Jan 11, 1917

By C. H. Snyder

The paper deals with details of construction of the Colmol, including improvements in design that will be incorporated in new models. These improvements are results of problems encountered and worked out in experimental operation with the unit. Also included is a descriptive plan of operating where roof and air conditions are of the worst. A summary of production results from the machine is presented.

Jan 6, 1950

[EDMUND M. WISE, Chairman ROBERT H. LEACH, Past-Chairman D. K. CRAMPTON, Vice-Chairman CARL E. SWARTZ, Vice-Chairman W. M. CORSE, Treasurer LOUIS JORDAN, Secretary 29 West 39th St., New York, N. Y. Executive Committee 1941 1942 E. A. ANDERSON FRANCES H. CLARK D. L. COLWELL W. L. FINK W. P. SYKES J. T. NORTON 1943ERIC R. JETTE LOUIS W. KEMPF GEORGE SACHS]

Jan 1, 1940

By Z. E. Arlin, R. D. Lynn

A deep well injection system is used by The Anaconda Co. for the disposal of uranium mill tailing water near Grants, N. M. A 2511-ft hole was cored and tested through Triassic, Permian, and Pennsylvanian (?) sediments and bottomed in Precambrian granite gneiss. The disposal well was plugged back to 1830 ft and completed in 563 ft of sandstones in the Yeso formation. The reservoir sandstones contain water similar to the injected waste water, and are isolated from overlying fresh-water aquifers by an evaporite barrier zone. Mill tailing water is decanted, filtered, and introduced into the well by gravity at an average rate of 400 gpm. The reservoir has a life expectancy of 10 years. The Anaconda Co. began uranium milling operations near Grants, N. M. in 1953 with a small mill that processed limestone ores. A larger second mill was built in 1955 to treat sandstone ores. In 1956 it became apparent that a large tailing pond would be required to contain the increased discharge of mill waste water. Research was begun on supplementary methods of disposal by which a minimal pond size could be maintained to avert excessive seepage losses. An intensive sampling program was begun to monitor the fresh-water wells in the area. The original limestone mill ceased operation in 1959. The present mill treats sandstone ores by sulfuric acid leach and a resin-in-pulp ion exchange recovery circuit that uses chloride elution. Process waste water is discharged to a tailing pond where, after evaporation losses, an annual average of about 400 gpm are available for injection into the disposal well. The waste water is a mildly acid solution that contains large amounts of manganese, iron, and the sulfate and chloride salts of sodium, calcium, and magnesium. It is a low-level radioactive fluid that contains small amounts of Uranium-natural, Thorium-230, and Radium-226. The average chemical and radioactive analyses of the waste water injected into the disposal well are shown in Column B of Table I. Disposal of the excess mill waste water by deep well injection was investigated after extensive research had proved that alternate methods were not satisfactory. A study of the regional geology and hydrology indicated that a disposal well was feasible, and a test well to basement rock was planned. Tentative plans for the test well and the results of the geologic and hydrologic studies were submitted to the New Mexico Dept. of Public Health, the New Mexico State Engineer's Office, the U.S. Atomic

Jan 1, 1962

By R. D. Vaughn

The analysis of laminar flow of power-law non-Newtonian fluids in narrow, eccentric annuli is employed in this paper to discuss the problems of lubricant flow in journa! bearings and of errors introduced by eccentricity in experimental studies with concentric annuli on extruders and wellbore annuli. The velocity profile and pressure loss-flow rate equations are developed for the laminar flow region. In addition, the expected error in flow rate and pressure-loss measurements for concentric annuli as a result of eccentricity is determined. For example, a 10 per cent displacement of the core of an almost concentric annul us would cause a 1.8 per cent decrease in the observed pressure loss for a fluid with a power-law exponent n of 0.25. The corresponding increase in the observed volumetric flow rate would be 7. 5 per cent. INTRODUCTION Non-Newtonianism and eccentricity occur simultaneously in two engineering problems: (1) flow of lubricants in journal-bearings and pressure-reducing bushings, and (2) flow of non-Newtonian fluids in plastic extruders and wellbore annuli. The lubricants used for moving parts are often non-Newtonian in character — often they are plastic in behavior. A solution to the problem of flow of non-Newtonian fluids in narrow eccentric annuli is particularly pertinent to this problem. In all experimental studies of laminar flow of fluids in concentric annuli, such as in extruders and well casings, the error due to eccentricity must be estimated or studied. A number of publicationsl-4,6,7 have dealt with this problem for Newtonian fluids; however, I am not aware of work for non-Newtonian fluids. This work is directed to the non-Newtonian problem. Before the solution to the problem is given, the pertinent conclusions from the work on Newtonian fluids will be reviewed. Heyda 1 and Redberger and Charles 2 have published general solutions to the problem of the laminar flow of Newtonian fluids in eccentric annuli, apparently without knowing of the earlier work of Ca ld well 3 and Bairstow and Berry,4 which is reported by Dryden, et al. 5 Although several mathematical routes are encompassed by the work of these authors, the results appear to be equivalent. Redberger and Charles2 show that the error caused by eccentricity in concentric annuli is negligible for small diameter ratios (k < 0.5); however, for large diameter ratios (k + l), the error in the predicted flow rate can be as great as 100 per cent or more. Partial solutions to the problem are available from the work of Dryden,5 Tao and Donovan6 and Piercy, et a1.7 Tao and Donovan examined the case of flow in narrow, eccentric annuli (k + 1) with and without rotation of the annular core. These authors also reviewed previous work on this subject and verified their approach with experimental data. Dryden gives the solution for the limiting case of complete eccentricity or tangency. Piercy, et a l. published an early solution to the problem of narrow eccentric annular flow. The conclusions of Redberger and Charles2 and the experimental proof of Tao and Donovan6 both suggest that the region of large diameter ratios (k + 1) is of main interest and that the parallel planes approximation to the solution in this region is satisfactory. This method will now be extended to the laminar flow of non-Newtonian fluids in narrow eccentric annuli. THEORETICAL SOLUTION The geometrical aspects of the problem are illustrated in Fig. 1. To represent the non-Newtonian fluid the power-law model was selected. This model has many disadvantages which have been pointed out; nevertheless, its simplicity, its frequent and wide applicability justify its use in this work. Fredrickson and Bird8 and Savins9 have used it as a basis for a theoretical study of laminar flow of non-Newtonian fluids in concentric annuli.

Jan 1, 1966

By J. M. Smith, G. P. Willhite, J. S. Dranoff

Heat transfer rates were measured in sandstones with flow of gases perpendicular to the direction of energy transfer. Effective thermal conductivities ker ranged from 0.7 to 1.7 Btu/(br)(ft)(°F). The contribution of the solid phase appeared to be the most important in these consolidated materials, although the thermal conductivity of the gas had some effect. The velocity of the gas through the pores of the sandstones had no influence upon ker up to values of 168 lb/(br) (sq ft) in agreement with data obtained for unconsolidated beds of glass beads. The present results indicated that gas mixing, and hence heat transfer by convection in the pores, is less for perpendicular transfer of energy than when fluid flow and energy transfer are in the same direction. HEAT TRANSFER PERPENDICULAR TO FLUID FLOW IN POROUS ROCKS Heat transfer in porous media with pore sizes in the micron range depends upon the fluid in the pores and the geometry of the solid phase. The best characterized system is a bed of solid spherical particles. Heat transfer in this system has been studied extensive1y (Ref. 8 summarizes the literature up to 1959) when the pores contain stagnant fluid. When the fluid is in motion the directions of flow and energy transfer have an effect on the heat transfer rates, as demonstrated by comparing the work of Willhite, et al l3 for perpendicular flow and that of Kunii and Smith9 for parallel flow of energy and fluid. For perpendicular flow, no increase in effective thermal conductivity ke was noted up to mass velocities G of 77 lb/(hr) (sq ft). In contrast, for parallel flow ke, increased with G in the same range of flow rates. These higher values of ke in the direction of flow also have been observed3,4,10 in beds of larger particles, 0.1- to 0.5-in. diameter. For beds of consolidated materials, such as porous rocks, data are not available for these compar- isons, although Adivarahan1 reported results for the parallel case. Hence the primary objective of this work was to measure ke values for perpendicular flow of fluid and energy in porous rocks. Of interest also was the variation in effective conductivity with fluid velocity. APPARATUS AND PROCEDURE In the experimental method, a constant heat flux was applied to the inner surface of an annular section of the porous rock. By cooling the outer wall, a temperature gradient through the annular sample was established and measured with thermocouples placed within the sample at various radial positions, and at three elevations (A,B.C). The location of the 2-in. O.D., 3.75-in. long sample in the apparatus is shown in Fig. 1. Fluid entered the bottom (1) of the 3-in. I.D. (approximate) steel shell, flowed upwards through the sample and out at the top (3). pressure taps (2,4) were used to check the permeability of the sample. The energy flowed radially from the centrally-located electric heater through the sample and was absorbed in the water-cooled jacket. The samples studied were naturally occurring sandstones from different locations with the properties given in Table 1. These materials are identical with those used by Adivarahan 1 for the parallel flow of energy and fluid. Prior to use they were refluxed with toluene to remove hydrocarbons and leached with distilled water to remove soluble salts. Each sample was visually examined and discarded if large nonhomogeneities, such as cracks or stone particles, were noted. Eight copper-constantan thermocouples were inserted in holes drilled radially into the sample with

By Edwin A. Zink, Gerald P. Zink, John E. Wolgamott

Recent advances in high-pressure water technology can be effectively employed in underground mining. The new equipment is based on standard industrial water cleaning hardware and is compatible with conventional mining techniques. Three viable applications are addressed: rock drilling, hole notching, and rock bolting. Highlights of test results are presented that were obtained in several underground mines during the last two years of development work.

Jan 1, 1982