Search Documents

Industrial relations on Australian and New Zealand resource projects can be volatile. Therefore investors have become increasingly aware over the years that sound industrial relations during construction is vital to the overall success of their project. There has been a wide range of actual industrial relations performance, project by project, and the degree. of success often directly correlates with the degree and thoroughness of pre-project planning. However, although many projects have been crippled by delays and cost overruns because of labour disputes, good results are achievable. Total commitment to the project by all parties involved is essential and it is up to the employers to seek out this commitment and not just trust mother luck. Industrial relations must be taken very seriously as the price of failure can render a resource project unviable.

Jan 1, 1983

By M Simpson, K Brodie, J L. Mauk

Subaqueous water-rock reactions that occur at the pit wall/lake water interface can affect the pH of pit lakes. Many pit lake water chemistry models neglect subaqueous reactions, which may create inaccurate predictions over time. A mineral quantification method is presented that defines the wall rock mineralogy of active open pit mines, using samples collected from the Martha Mine, a low-sulfidation epithermal Au-Ag deposit in Waihi, New Zealand. The mineral quantification method has five components: field observations and sampling, X-ray diffraction analyses, selection of representative samples, geochemical analyses, and mineral accounting. Predicted mineral concentrations closely match observed mineral concentrations visually estimated using petrographic techniques. Results of the method can be incorporated into a geochemical model of long-range pit lake water quality resulting from subaqueous water-rock reactions.

Jan 1, 2003

Commissioning is one of the many phases of a project, it has inter-dependencies with the other phases, as they have amongst themselves, and has its own terminology and distinctive features. Commissioning time and cost can severely affect project economics, especially through unrealistic estimating, and requires a separate management team to ensure full control is. maintained. Targets to be achieved in commissioning are identified, together with the necessary policies to achieve them. Factors which have to be taken into account in applying these policies are Discussed.

Jan 1, 1986

By F Brenguier, R A. Lynch, G Olivier

The seismic velocities of intact rock are dependent on the applied stress. Unfortunately, the low susceptibility of seismic velocity to stress changes mean that changes in seismic velocity have to be measured extremely accurately to infer stress changes from them. Previously, it was thought that measurements of this accuracy could only be made with active sources or repeating earthquakes. In this paper, we show that the noise generated by mining activity can be used to construct virtual seismic signals with which we can measure changes in seismic velocity accurately enough to see the short- and long-term effects of a production blast on the surrounding medium. The time-dependent velocity variations achieved with this method show that the blast caused weakening of the rock mass for the rock within a radius of 200 m of the blast. The weakening is healed by confining stresses over a period of five days, after which permanent changes in the seismic velocity can be seen. The size and spatial distribution of the seismic velocity changes were compared to modelled changes in static volumetric stress, which supported the notion that seismic velocity changes can be used to measure the redistribution of stress after a blast. The results of this study indicate that this method can be a powerful tool to evaluate the evolution of stress in a mine at a relatively low cost as the data that it uses would normally be discarded.CITATION:Olivier, G, Lynch, R A and Brenguier, F, 2016. Measuring the redistribution of stresses resulting from new excavations with ambient seismic noise correlations, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 873–878 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

ALTHOUGH discovered as long ago as 1817, by Strohmeyer, the use of cadmium did not become in anyway general for nearly a century. Its properties, although well known, did not recommend it to users of metals generally, and it was, on the whole, regarded more in the light of a nuisance to zinc producers than anything else. Its real value was not appreciated until both the United States of America and Germany, who are entirely dependent on outside sources for their supplies of tin, were faced with the unpleasant fact that their tin stocks were being rapidly depleted, with practically no prospect of having them replenished. This resulted in serious efforts being made in the UnIted States of America to conserve what tin was available, and, as a consequence, several metals were tried in the hope that they would prove satisfactory substitutes for tin. Among these was cadmium, and it was found that cadmium could replace tin in a manner sufficiently satisfactory to permit of its use in many directions where tin had been used before.It is on this ability of cadmium to replace tin that its use became in any way general at first; but since then new avenues of development have been opened up in which its physical and chemical properties are proving their value. It is highly probable that its use will extend very considerably as time goes on. OCCURRENCE OF CADMIUM.There are several cadmium minerals known, but none of them occur in profitable quantities as ores. The cadmium of commerce is derived almost entirely from zinc minerals and ores in which it is almost invariably present in proportions which are usually very small. Cadmium behaves metallurgically almost the same as zinc, and hence constitutes a fraction of 1% of almost all spelter.

Jan 1, 1923

Determining the environmental consequences of green field projects is becoming an increasingly important component of new projects. Feasibility studies are regarded by potential investors as incomplete if a comprehensive Environmental Impact Assessment (EIA) has not been completed. These EIAÆs need to meet various local and international requirements in order to achieve bankability. Heavy mineral mining projects are often located in ecological sensitive coastal zones, and bring with them a suite of social impacts in the mainly developing countries within which they are usually located. This paper draws on experience gained in undertaking EIAÆs for heavy mineral mining projects in Kenya, Mozambique and South Africa, and uses these case studies to identify potential pitfalls. Important lessons include the need to initiate the EIA process as early as possible in the project, in order to develop management systems to mitigate the environmental impacts of exploration. Close and on-going consultation with affected communities is also seen to be critical to the success of the EIA. Proactive participation on the part of the environmental consultants with the project team and all interested and affected parties (IAPs) is important. An EIA commissioned later in project planning makes it difficult for the EIA to contribute in a positive manner to the project. Early engagement with environmental consultants allows the environmental assessment to develop from a report to an actual process, and to become fully integrated with project planning. The proviso is that an initial æfatal flawÆ assessment is required to identify any potential æshow stoppersÆ, in order to meet one of the important objectives of EIA, namely an assessment of whether or not the proposed project is the preferred development intervention in the study area. For more controversial proposals this may require the commissioning of a Strategic Environmental Assessment (SEA), which circumvents some of the limitations of the project level EIA. Whilst confidentiality is a constraint to full disclosure, an open participatory approach to public consultation is essential to add credibility to the EIA process and to gain, at least, the acceptance of the process from the majority of IAPs. Full disclosure is encouraged by organisations such as the International Finance Corporation, who acknowledge that good public consultation costs a lot of money, but bad public consultation costs a lot more! An open approach to disclosure presents understandable difficulties for proponents, as they are required to give up some of their control over the project, and to trust the social scientists engaged in the process. However, independence in the EIA process is critical to its success. This paper will highlight these and other issues by drawing on five case studies to identify lessons learnt, and explore the above themes in more detail.

Jan 1, 2001

By Moy A. D

The Esperanza deposit is located 120 kin N of Mount Isa, Queensland at approximately lat 19¦20'S, long 139¦22'E on the Camooweal (SE 54-13) 1:250 000 scale map sheet. It is one of several structurally controlled copper ¦ cobalt deposits developed along the Mount Gordon Fault zone and related faults, within the Western Fold Belt of the Mount Isa Inlier (Figure 1). Together with the nearby Mammoth orebodies it forms the basis of the Gunpowder operation of Aberfoyle Limited. Until recently ore was mined from the Mammoth orebodies by open stoping with decline haulage to surface leach pads. Leaching of in situ broken ore (in place) and surface heaps, followed by solvent extraction and electro-winning (SX-EW), produced copper metal on-site. In March 1997, mining was suspended at Mammoth and the focus of the Gunpowder operation switched to development of the Esperanza orebody, which is expected to begin open cut production in mid 1998. SX-EW methods will produce 44 000 tpa of copper from an expanded plant. The pre-mining mineral resource at Esperanza (measured, indicated and inferred) is estimated at 4.6 Mt averaging 7.7 per cent copper.

Jan 1, 1997

By Rogis J

The basic parameters causing outbursts are rock pressure, gas characteristics and the physico-mechanical properties of the coal. The three sets of factors are to some degree interdependent. At Collinsville, the gas characteristics coupled with the physico-mechanical properties of the coal appear to be the major factors contributing to outbursts. The relative importance of rock pressure is uncertain. The following geological parameters appear to be necessary before outbursts can occur. 1. A coal rank greater than 1.2% vitrinite reflectance. 2. Thrust faults with throws greater than 3.Om or strike- slip faults with coal gouge wider than 0.3m. 3. Seam gas emission values greater than 1.1 cm3 /g. Igneous intrusions are the likely source of the carbon dioxide seam gas. Outbursts have occurred at depths ranging from 215m to 265m. They occur at these relatively shallow depths due to: 1. the high rank of coal at the present topographic surface and the high coalification gradient; 2. the relatively high degree of tectonic deformation of the strata; 3. the seam gas characteristics; and 4. the extent of igneous intrusions.

Jan 1, 1980

The last two years have seen a rapid change-over from mechanised cut and fill. stoping to the more economic and productive long hole open stoping method, such that today more than 80 per cent of total production is won from open stopes. At first drilling was by sub-level rings and/or parallel up and down holes from inter- mediate sill horizons using conventional exten- sion rod equipment. Sub-levels were developed no more than 40 metres apart to allow accurate drilling. Compact, crawler mounted in-the-hole hammer equipment was introduced as soon as it became available in Australia. Today, all open stope drilling is done with three Atlas Copco ROC306 rigs and two Ingersoll-Rand CMM jumbos. Fans of 115 mm diameter holes, varying from near vertical down holes to horizontal, are drilled with a burden of 3 m. Toe spacing varies from 3.5 m to 4 m. An Atlas Copco DG418 booster compressor is used to boost run-of-mine air from 700 kPa to 1400 kPa in the areas of longest drilling. This has improved overall drilling performance in these areas by 40 percent.

Jan 1, 1977

Natural gas from the south west Queensland gas fields is now available in north west Queensland to fuel the development of many Carpentaria Mineral Province projects. Like these projects, the south west Queensland gas project, developed under the operatorship of Santos Ltd, has its own æMining CycleÆ. While the project is entering its third expansion phase, it is at the same time actively extending its discovery phase, with large programs of gas exploration and reserves definition. This paper outlines the history of the south west Queensland gas project, with particular emphasis on the relationship of the project to north west Queensland.

Jan 1, 1998

By V Salamakha, K Tang, G Si, J Oh, X Wu, Z Yu

The development of machine learning (ML) algorithms has led to promising advances in lithology classification from geophysical logs, which is indispensable in various underground engineering applications. Due to the resolution and availability of logging data, ML models can recognise lithology change in a definitive form at a fine scale (0.01 m). While the results from previous models indicated promising performance in the classification, the robust capability of generalising lithology prediction to unseen data may not be true for those models due to: (1) data bias caused by borehole selections, and (2) logging data mismatches among boreholes. To this end, this paper aims to investigate the generalisability of ML models and seek potential improvements. Four ML models were selected to be trained on single reference boreholes to test the other (as unseen) in the same region, which includes Support Vector Classifier (SVC), Random Forest (RF), eXtreme Gradient Boosting (XGBoost) and Residual Neural Network (ResNet10). The data set involves 11 boreholes from a coalmine in north-western Bowen Basin (Queensland, Australia): density, gamma ray, neutron, and sonic logs are selected as inputs. Additionally, a data adaptation method is applied for better generalisability. The results show that there is an accuracy trade-off between the same borehole and unseen boreholes across the models. It also indicates a 16–43 per cent reduction in model performance when generalising the predictions (in marco-F1 score), while the adapted data sets can contribute to a around 12 per cent improvement. This study provides a fundamental understanding of the model generalisability when using a single borehole, essential for further correlating boreholes for regional lithology classification; the adaptation method can improve the generalised accuracy, and reduces the labour to label lithology, which facilitates the identification of gas storage mechanisms, geological/geophysical modelling, and stratigraphic analysis.

Sep 1, 2024

By Dawes S

Efficient roof control in colliery operation is a factor that must be maintained for· the maximum reQovery and economic extraction of the mineral. It must be carefully considered in each of the following stages in the life of a mine.1. The primary development and the first working of the mine.2. The maintenance of access roads, intake and return airways.3. The extraction of pillars.FACTORS IN ROOF CONTROLThe main objects of roof control are: The support of the roof in working places, the relief of roof pressure from the workings during pillar extraction, and in some instances the prevention of subsidence of the surface.The support of the roof during development operations and first working, and the subsequent maintenance of these is influenced by:-1. The depth of the seam below the surface.2. The thickness of the seam.3. The dip of the seam.4. The condition of the roof and floor.5. The method of extraction-mechanical or by hand.6. The method of. working-Iongwall or bord and pillar.7. The availability of material.As a general rule, the pressure exerted by the superincumbent strata may be taken as one pound per square inch for each foot of cover, and the crushing strength of coal as 1,500 to 2,000 lb. per square inch; this, of course, varies, but from these figures it may be assumed that seams below 2,000ft. in depth are liable to crush. If any part of the seam is removed, added weight is thrown onto the remaining coal. It is therefpre essential that for effective working this extra weight must be removed or supported as soon as possible.The outstanding principle in the support of mining excavations is to ensure that the supports are set as soon as possible after the natural support has been removed.Where a system of bord and pillar is applied, the early setting of supports reduces the extent to which the roof bends, thereby reducing the liability to ·tension fractures at the centre of the road.

Jan 1, 1947

By Sale M, Clarke R, Parker M

The Mount Gibson goidmine is located at the southern end of the Retaliation greenstone belt within the Murchison Province, approximately 300 km northeast of Perth, Western Australia. Economic gold mineralization occurs in the upper part of a Tertiary lateritic surface; its ultimate source presumably being Archaean greenstones. Gold is present in the laterite profile over a distance of 4 km in four separate prospects, from north to south, Mount Gibson Well, Midway, Orion and Tobias Find, the two last constituting the Mount Gibson mine. The area has'low relief. A low ridge to the west of the mineralized zone is formed mainly of rubble with minor outcrops of mafic volcanic and intrusive rocks. The terrain slopes gently to the northeast, and the maximum relief, in the vicinity of the mineralization, is about 20 m. The weathering profile comprises, from the surface: (i) soil, windblown sand or colluvium (thin), (ii) laterite; hardcap (including ferricrete and lesser silcrete and calcrete) is overlain by loose nodules and pisolites, and passes downwards into a mottled zone of variably ferruginized clay, (iii) clay; mainly pale brown, cream or yellow in colour, but in places contains relic quartz veins or dark ferruginous zones, (iv) clay with fragments of altered rock; normally grey to pale green in colour but sometimes includes an oxidized iron-rich horizon just above the weathered/fresh rock interface, (v) bedrock. The complete profile varies from 10-100 m thick, averaging 20 m. Zone (ii) is commonly 3-5 m thick. Loose pisolites of this zone fill cavities in the massive ironstone left by former tree roots, and cover irregular depressions which may represent former stream courses. Samples, representing 3 m intervals down the holes, have been collected from cuttings taken from rotary drill-holes along each of four traverses; one traverse at each-of the northern prospects and two traverses in the Orion part of the mine area. These samples have been submitted for X-ray diffraction analysis and for chemical analysis for a wide range of elements. Bedrock lithologies have been determined from microscope studies of bottom-of-hole chips.

Jan 1, 1988

The major technological advances of the last 30 years have profoundly reshaped mining practices. Machines keep getting bigger while productivity continues to increase and manning levels drop. These trends will continue and the introduction of breakthrough technologies will continue to accelerate, driven by a continued focus on lowering the cost of production, improving the productivity of workers and machines, and ensuring safer working environments. At the same time, global consolidation of mining companies has impacted on technology development in a range of ways. There are many potential technologies being proposed, some already operating in Australian mines. The automation of underground load-haul-dump (LHD) trucks for example, continues the process of removing workers from the most dangerous operating environments. Global positioning systems fitted to draglines, fibre optic communication channels, and 400 tonne trucks are only some examples of what lies ahead. However, where we need to return focus is to the technology of management û which is also one of the two key interrelated themes of this keynote address. Have we, as an industry, adequately been able to keep up with technological advances? Are our management systems as competent as the machinery we employ? The other key theme is the processes of globalisation and consolidation. What are the impacts on our industry? What are the implications of these processes, particularly for the ways in which we manage our people? My paper is divided into several components:some comments on the coal industry and the dramatic restructuring we have seen in recent years; in the context of this restructuring, an overview of my company and its evolution; my views on the role of contractors; some comments on the consolidation also occurring in the mining machinery and equipment, technology and services sectors; some observations on two major areas of technology û drill and blast; and trucks, shovels and excavators; the implications of consolidation and new technology for our employees and management; and finally some comments on research programs.

Jan 1, 2001

By H G. Poulos

Prediction of ground deformation caused by soft ground tunnelling is an important problem facing design engineers. The ground deformations are caused by the closure of the gap formed around the tunnel due to the tunnelling procedure and soil intrusion via the tunnel face into the tunnel. There are three different approaches that are commonly used in practice to estimate the ground deformations due to tunnelling, namely, empirical methods, analytical methods and finite element methods. One of the important issues of tunnelling in urban areas is the assessment of the likely impact on adjacent pile foundations of ground movements arising from tunnel construction. The main objectives of this paper are two-fold: first, to assess the available methods to estimate the tunnelling-induced ground deformations, and second, to examine the effect of such ground deformations on adjacent piles. Analytical solutions to predict the tunnelling-induced ground deformation developed by the authors are used in this study. These estimated ground deformations are imposed on the pile in simplified boundary element analyses to compute pile responses. The influence of various factors such as tunnel geometry, ground loss ratio, pile diameter and ratio of pile length to tunnel depth are examined in this study.

Jan 1, 1999

By T Napier-Munn, E Louwrens, L Keeney

Geometallurgical characterisation of ore deposits is accepted practice in some parts of the mining industry today. Its primary aim is to provide constrained inputs that reflect inherent geological variability and its impact on metallurgical performance for the deposit. Geometallurgy improves project value because it suggests more valuable alternatives for scheduling and processing through an increased knowledge and understanding of the interactions of rock properties and extractive technologies. Lower project cost (both capital and processing) and improved recoveries are the result from closer tailoring of the mining and mineral processing strategies to the characteristics of the resource (Dunham, Vann and Coward, 2011). Tailings storage facilities (TSFs) can be seen as potential resources and it is argued that fundamental geometallurgical characterisation as applied in ore deposit characterisation should also be applied to planning the retreatment of TSFs. This paper will describe a research project at Julius Kruttschnitt Mineral Resource Centre assessing if geometallurgical principles and methodologies can successfully be applied to TSFs as they have been to primary deposits. The project is establishing a new standard method of tailings evaluation which will include a 3D spatial model of the tailings resource. Initial domaining of the TSFs was done using principal component analysis followed by k-means cluster analysis based on chemical assays from drill core samples. The subsequent characterisation of the drill core samples has involved chemical, mineralogical and metallurgical profiling, with a range of metallurgical tests being conducted on the samples. This characterisation step is followed by class-based analysis, predictive modelling and process performance domaining with the ultimate objective of establishing a 3D spatial model incorporating geochemical, mineralogical and metallurgical performance data. This approach, which takes into account processing performance permits a more realistic (as compared to doing limited chemical assays and metallurgical testing) economic evaluation of the potential of reprocessing the tailings material. It is believed that the approach is generic and can be applied to other TSFs being considered for reprocessing. The present case study has also established the gold, copper, magnetite and cobalt deportment for an iron oxide copper-gold deposit tailings resource.CITATION:Louwrens, E, Napier-Munn, T and Keeney, L, 2015. Geometallurgical characterisation of a tailings storage facility – a novel approach, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 125–132 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By M W. Chen, I Canbulat, S Saydam, C G. Zhang

The height of fracturing (HoF) measures the propagation distance of continuous fracturing from the mining horizon and is also termed the height of cracking (Hebblewhite, 2020; Khanal et al, 2019) or hydrologically the height of groundwater drainage (Tammetta, 2013). In longwall practice, HoF is an important predictive indicator for assessing the dewatering effect of panel extraction on the shallow aquifer and surface flows. The HoF determination is basically dependent on field measurement works, typically using surface extensometer, borehole televiewer imaging, piezometer monitoring, packer testing, borehole breakout logging, and isotopic tracer monitoring (Brown and Walsh, 2022; Corbett, 2022; Hebblewhite, 2020; Holla and Armstrong, 1986; Mills and O’Grady, 1998; Walsh et al, 2022a, 2022b). These methods or tools have been widely applied to observe rock fracturing and groundwater responses to longwalls at Australian coalmines, for example, Dendrobium Mine (Brown and Walsh, 2022; Walsh et al, 2022b), Appin Mine (Walsh et al, 2022a), and Springvale Mine (Corbett, 2022). In Chinese mines, borehole televiewer imaging and packer testing are more frequently used due to convenient instrumentation, quick testing, and not requiring long-term maintenance of the instrumentation boreholes. The HoF determination also involves further raw data interpretations, for which specialist software for data extraction and quantitative criteria for bounding the fracture transition and termination are necessary. By combining the measured fracture distribution and longwall parameters regarding panel geometry and geological settings, several HoF models have been developed for conceptualising the understanding of strata depressurisation and providing mine engineers fast calculation tools for HoF prediction. The Mackie model considered the height of fracturing as the upper bound of fractured zone and revealed that within the fractured zone there are highly connected fractures and accordingly porosity enhancement and groundwater depressurisation, where the fracture network can be less transmissive from the mining horizon up (Hebblewhite, 2020). The fractured zone shares similar fracturing regime but different heights in varying models: HoF is 30 to 58 times of the mining height (t) based on Australian, Soviet and UK experience (Kendorski, 1993, 2006), and 21 to 33 t according to the field measurements in NSW Central Coast, Australia (Galvin, 2016). Some Australian longwall mines adopt Ditton model (Ditton and Merrick, 2014) (Equations 1.1 and 1.2 in Table 1) sourcing from NSW coalfield experience for HoF prediction, while Liu model (Liu, 1981) (Equations 2.1 to 2.4 in Table 1) developed from 27 coalmines in China is frequently used by Chinese coalmines.

Nov 29, 2022

By A Whaanga, A Doecke

The internal stratigraphy of the Marillana Creek palaeochannel Tertiary channel iron deposits (CID) in the Hamersley Province of Western Australia was initially defined in the 1980s and redefined as the Marillana Formation in the early 2000s. Recent drilling, open pit mining and field observations in the Western deposits at BHP Billiton Iron OreÆs Marillana Creek tenements have revealed some additional details on the extent and detail of some units of the Marillana Formation stratigraphy in this area. The drill hole data at Western 1 South has identified a number of features either not previously documented in this area or whose significance has not been adequately recognised, including a denatured zone at the base of the Upper CID of the Barimunya Member, and variations in the lithology within the Munjina Member at the base of the channel. Additionally, the Western 4 pit walls show evidence of a significant near-surface clay horizon and overlying CID, which are suggested to be the equivalent of the Iowa Eastern Member in the Eastern deposits. The deposition of this unit was most likely driven by a regional climatic disruption rather than a change in sediment source area alone. The nature of the Weeli Wolli Formation-derived goethitic peloids in the Western deposits may explain the more extensive denaturing in the Western Lower CID of the Barimunya Member. In contrast, the more robust nature of the haematitic-cored pelletoids in the Central and Eastern deposits has resulted in a less denatured Lower CID in these areas. Such work reveals the value of and need for geologistsÆ ongoing face mapping observations and detailed drill hole logging, and cautions against not querying previously accepted interpretations.

Jan 1, 2007

Naturally occurring rutile contains approximately 96 per cent titanium dioxide (Ti02), whereas the product from the ilmenite reduction - aeration upgrading process, "sub- rutile", contains only about 92 per cent Ti02. Therefore, there is an-incentive to lift the quality of sub-rutile by removing transition metal impurities, in order to supply a more valuable and marketable product, particularly for the chloride-route pigment producers. Previous studies have shown that the sub- rutile residual iron content (of approximately 4 per cent) and residual manganese content (of approximately 1.5 per cent) are chemically bound within the titanium-oxygen mineral lattice, and are most difficult to remove by simple leaching methods. In attempts to improve their eventual removal, a simple process modification has been successfully investigated in laboratory scale trials. Transition metal sulphides have been formed in the reduced ilmenite by using a "sulphur-doping" technique during reduction (metallization) conducted at controlled temperatures. These compounds give rise to greatly enhanced dissolution of the unwanted transition metal constituents during the sub- sequent aeration and acid washing steps. Thus, the manganese content of the final sulphur- doped, reduced-aerated, acid washed product can be reduced by about 90 per cent to 0.2 per cent, and the iron content by about 70 per cent to less than 1.5 per cent, in comparison with those levels remaining after unmodified pro- cessing. Additions of sulphur as low as 2 per cent of the weight of the ilmenite have proven satisfactory. Preliminary studies reveal that the modified process is economically feasible. These results suggest that the sulphur content of the Collie coal char used in an unmodified reduction step must exert some influence on the eventual removal of iron and manganese during aeration and acid washing.

Jan 1, 1973

By Wyborn L. A I, Idnurm M, Hinman M. C

Comparison of the Proterozoic Apparent Polar Wander Path (APWP) for Australia with the corresponding geology of northern Australia suggests that a number of discrete interplate tectonic events, manifested on the APWP as bends or inflections, may have controlled sedimentary basin evolution, ore fluid production and the timing of mineralisation. Similar features in the Phanerozoic APWP for the North American plate appear to correlate with major orogenic events, basin deformation, movement and 'entrapment' of hydrocarbons and minerals. Interplate tectonic events cause intraplate deformation which in turn controls the subsidence/uplift and sedimentation histories of the basins. Interplate events are thus responsible for creating, deforming and destroying sedimentary basins and the associated petroleum and mineral systems. The basins of northern Australia show remarkable similarities in the successions of volcanic and sedimentary deposits. Unconforrnities of regional or sometimes only local extent have been mapped between the major sedimentary sequences and it is predicted that interplate tectonic events corresponding to bends or inflections on the APWP directly reflect the processes that have produced these widespread unconformities. These processes are also likely to have controlled the geometry and character of the fluid migration pathways and hence the mineralising events. Palaeomagnetic studies of Proterozoic rocks in sedimentary basins provide a tool for predicting the timing of regional mineralisation events, particularly for low-temperature mineral systems. The techniques, when coupled with systematic regional basin analysis, using petroleum exploration techniques, may identify a number of new mineral 'plays' in northern Australia. Prominent inflections in the APWP occur at approximately 1700, 1670, 1650, 1600, 1540, and 1480 Ma. Each of these may be related to a regional compressional deformation, important mineralising event, or significant change in style and type of sedimentation. Most appear to be associated with magnetic overprints. Some of the inflections between 1400 and 540 Ma may also mark significant events in the evolution of Meso- and Neoproterozoic basins. Further work is required to correlate inflections in the APWP with alteration events in order to understand their regional significance.

Jan 1, 1994