Search Documents

By Donald Crowell

Due to falling metal prices and depletion of ore reserves, lead-zinc mining in the Leadville, Colorado, area gradually came to a halt in the 1950's. Exploration work continued, however, and by 1969 sufficient ore had been blocked out to warrant sinking a shaft and erecting a new concentrator to treat 700 tpd. The new shaft and concentrator were to be located in Iowa Gulch several miles east of Leadville at an elevation of 11,100 ft. The Leadville project is a joint venture between Newmont Mining Company and ASARCO with ASARCO being the operator. Design work began in the fall of 1969. Engineering was done by Torkelson Engineering Company of Salt Lake City in conjunction with the Central Engineering Department of ASARCO. The plant was constructed by Stearns-Roger Corporation. Construction began in the spring of 1970 and the plant went onstream in April, 1971. Flow sheets and equipment lists are attached. This paper will describe the flow sheet very briefly and discuss in more detail those aspects of the design which may be of interest, particularly the provisions for expanding the capacity of the plant.

Jan 1, 1972

By T. Dunn

FMC Corporation has achieved a significant cost reduction through a new proprietary solution mining and processing technology at its Green River, Wyoming Soda Ash Facility. In the first phase, completed in October 1995, trona ore is dissolved, recovered and processed with the new technology, and then fed into an existing refining plant, replacing dry mined and calcined trona ore. The second phase, completed in April 1996, produced a fmal high purity product and increased capacity by 635,000 t/a (700,000 tpy). Both phases were completed under budget and well ahead of schedule.

Jan 1, 1998

By N. Arbiter

Evidence for the floatability of sulphide minerals without collector is analyzed and it is shown that results obtained with ores, in contrast to those with single minerals or mineral mixtures, depend on many additional variables, some identified and others not. Because of the prevailing low levels and costs of collectors for most sulphide ores, it is unlikely that collectorless flotation will have commercial applications, so that continued research on the subject may be justifiable on theoretical but not on practical grounds.

Jan 1, 1993

By W. P. Diamond

The Bureau of Mines has been investigating several techniques, including the use of horizontal and vertical boreholes, to remove gas from coal in advance of mining. Horizontal boreholes drilled from underground workings as part of the mining cycle have been shown (Finfinger, 1980; Hagwood, 1983; Perry, 1978; Prosser, 1981; Thakur, 1980; VonSchonfeldt, 1982) to be very effective in providing short-term, immediate relief from high methane emissions. This technique has been widely accepted in the coal mining industry, but it does require close coordination to integrate the drilling and subsequent gas drainage and disposal into the projected mine development plan. Vertical boreholes can be placed several years in advance of mining to predrain gas from coalbeds over relatively large areas (Dunn, 1984; Elder, 1975; Lambert, 1980; Steidl, 1978; Stubbs, 1979). The vertical borehole technique has the additional advantage over horizontal boreholes of allowing work to be performed on the surface instead of in the more restrictive underground environment. However, except for the relatively large scale vertical borehole programs for both mine safety and commercial production in the Black Warrior Basin of Alabama (Dunn, 1984; Lambert, 1980; Stubbs, 1979), the technique has been underutilized. The primary reason for this seems to be a combination of the current economic climate in the coal industry, legal questions as to the ownership of coalbed gas, and potential roof damage from the stimulation treatments required to increase the characteristically low permeability of coalbeds to enhance gas production. The question of potential roof damage is the subject of this paper.

Jan 1, 1985

By John E. Tilton

Mining is one of the oldest human activities. It goes back at least to the Bronze Age and possibly even the Stone Age. The Romans mined copper in Spain and tin in England some two thousand years ago. The writings of Agricola in the 16th century show that mining was important in the Middle Ages. Today we mine more mineral commodities in greater tonnages than ever before. This long and fascinating history closely tied with the economic development of the human race is one of the charms of the mining industry. It also, unfortunately, gives rise to some widespread misconceptions.

Jan 1, 1997

By Newell H. Orr

Titanium's performance characteristics in acidic oxidizing and mildly reducing environments make it applicable to numerous currently defined and many projected hydrometallurgical applications. With titanium's current and projected availability and price stability increased use in pressure leach, piping systems and electrorefining is practical.

Jan 1, 1983

By M. D. Flavel

My paper relates to bond's third theory of comminution and suggests work be used as a basis for designing crushing and screening plants, this will give more accuracy than existing methods, As stated in the abstract, this paper is only a synopsis of my official paper, many of the questions that might arise in this brief address will be answered by referring to the detail i n the main paper $ Because of the limited time available and the fact that many people here do not need to study the aspects of crushing and screening in depth, i will highlight-those sections of the paper which show how major capital, operating and energy cost savings can be achieved in the process, I will develop the theme in the following manner, Firstly, pointing out, why a new approach is needed to the fundamentals of crushing and screening, Secondly, by setting forth some theory to describe what we are trying to accomplish, Thirdly, by looking at important factors which need to be observed in designing plants and applying machines to comply with this theory, Lastly, i will put forth some ideas on how we might develop this theory to make the industry more efficient, At the outset, i have to say my approach to this process is entirely new, for those used to applying machines and designing plants on existing criteria, they will find this theory easier

Jan 1, 1977

By Fredy A. Elorrieta Agramonte, Gabriel von Rickenbach, Roberto Luis Fonseca, David Córdova Rojas, Rolando Romero, Rico Brändle

The mine’s economic life is dynamic by nature. Some factors that create this scenario are the need to recognize new exploitation areas, the evolution of the mineral prices and the development of new technologies to access them. The dynamics of mining development, especially in the underground environment, changes significantly as the stages unfold. In many cases the final solution differs greatly with the initial. The frequent presence of new conditions and factors often cause the mine to develop in a quasi-permanent transition stage, which could be characterized by the generation of dynamic micro-seismic events that could cause rockburst damage in some specific areas. Although they may be infrequent, these dynamic events can have an important adverse impact on mine safety and causes serious losses. Also, changes in the production schedule during exploitation could be a big issue if the problem is not effectively addressed. When the transition of the mine to an active micro-seismic environment begins as an unforeseen scenario, it is frequent to use static ground support systems as they are readily available. Traditionally, the support systems used are reinforced shotcrete with a middle layer of Welded Standard Wire Mesh (WSWM) and Chain Link Standard Wire Mesh (CSWM) of reduced gauges, i.e. wires less or equal than 4 mm in diameter. Although, this support system is used to control static instability problems, there is no good reference of its energy absorption capacity under dynamic load conditions, creating uncertainty in the effectiveness of controlling rockburst events. These support systems are analyzed at the present paper, testing the reinforced shotcrete layer with 4 mm diameter of WSWM and CSWN under dynamic load. Additionally, the influence of the use of high tensile strength steel wire in the meshes (HSWM) compared to the previous ones, is analyzed to assess the scope in controlling rockburst events and keeping the safety of underground environment.

Apr 26, 2022

By Valerio Violo, Antonio Raschilla, George Kafantaris

"The Cityringen project in Copenhagen, Denmark will form a new circular line in the city center and will consist of 21 new stations (17 + four transfer stations) and approximately 31 km (19 miles) of earth pressure balance (EPB) twin-bored tunnels.The new tunnels passed under the historical building of Magasin du Nord, McDonald’s and two pubs in the heart of the city with a minimum cover of about 4 m (13 ft).To minimize the movements, a complex system of compensation grouting and jet grouting soil treatment was performed. A detailed action plan between the parties involved allowed coping with the critical tunnel boring machine’s (TBM) successful passage.The Cityringen is an extension of the existing metro line underground Copenhagen and will include the City Circle Line, 15 km (9.5 miles) of twin tunnels looping around the city. The City Circle Line will form a new circular track inside the city center and will intersect the existing M1 and M2 lines at Kongens Nytorv and Frederiksberg stations, as well as suburban train services at København H, Østerport and Nørrebro. It will extend the Metro network to the Nørrebro, Østerbro areas and the central station at København H (Fig.1). The two new lines M3 and M4 will run on the same tracks, but the M3 will be a circle route running around the entire line, whereas the M4 will drive from the station to the north side of the city.The €1.5 billion design-build contract was awarded by Metroselskabet in January 2011 to the Copenhagen Metro Team (CMT), a joint venture (JV) between the Italian companies Salini, Tecnimont Civil construction and Seli SpA. Since the bankruptcy of Seli SpA and Tecnimont, Salini Impregilo now owns 100 percent of the JV shares. Seli Tunneling Denmark ApS, a subcontractor to CMT, was initially constituted as a Seli SpA subsidiary and, following the economic difficulties of Seli SpA, was acquired in 2015 by Salini Impregilo. Seli Denmark is in charge of the tunnels excavation and lining and owns the four 5.84-m (19-ft) diameter Seli/Kawasaki earth pressure balance machines."

Jan 5, 2017

By G. P. Larson

We define a specialized mineral market as follows: Specialized Markets are markets where a low volume of a given mineral is used to convey a large benefit to a specific product. Sales of these value added minerals to small markets generally require a different marketing approach compared to bulk or commodity markets for traditional minerals. Specialized and commodity markets are differentiated by several characteristics as listed in Table 1.

Jan 1, 1990

By Clyde M. Pearce

This paper describes the facilities at Pointe Noire, Quebec that Wabush Mines utilizes for the receipt, distribution, stockpiling and shipping of iron ore concentrate and pellets. The main topics to be covered will be: 1. - General description 2. - Concentrate receiving facilities 3. - Conveying circuits 4. - Stockpiling 5. - Vessel loading GENERAL DESCRIPTION The map of the eastern Quebec - western Labrador area as shown in Appendix #1 shows the location of Wabush Mines properties. You will note the Scully Mine located at Wabush Lake, Labrador, 235 miles north of the town of Sept-Iles, Quebec. Our neighbors, the Iron Ore Company of Canada have their properties further north at Shefferville, near by at Carol Lake and at Sept-Iles. To the Southwest, our other neighbors, Quebec Cartier Mining, have their iron ore processing facilities and their terminus on the St-Lawrence at Port Cartier. Concentrates are prepared at the scully Mine by mining, crushing, grinding, concentrating, drying and high tension separation for shipment by rail to Pointe Noire, Quebec. Pointe Noire is situated across the bay from the town of Sept-Iles, Quebec on the North Shore of the St-Lawrence River. The concentrate consists of 66% iron, 2 ¼ percent silica and practically no moisture, permitting the use of specially constructed railroad cars and handling facilities to convert the concentrate into pellets, the final product.

Jan 1, 1967

By Harry H. Peek

Artesian pressures of unusual magnitude occur in the deeper aquifer units beneath a considerable part of southeastern North Carolina and extend into South Carolina. The high pressures were first observed in 1968 in wells near Wilmington that were drilled to "basement" rock and which were screened between depths of about 260 to 300 m (meters). The pressure was recognized by Peek and Heath1 as an anomalous geo-pressure and unrelated to recharge conditions in the region. Since 1973, much new information has been obtained on hydro-geologic conditions in the area and a preliminary report on the deep artesian pressures was published in 1975.2 Most of the basic information has been obtained from groundwater research stations constructed by the Groundwater Section of the North Carolina Department of Natural and Economic Resources as a part of Ground-water studies in the Coastal Plain Region. These stations consist of an exploratory well drilled to basement rock with wells completed in each principal aquifer unit to provide data on aquifer characterestics, water levels and water quality.

Jan 1, 1977

By W. G. Fischer

Trona ore at the Westvaco mine of FMC Corporation has been obtained by room- and-pillar methods since the mine began operation. The flat-lying, 10-foot bed of trona, Na2CO3 NaHCO3 2H2O, is covered by 1500 feet of weak shale and sandstone. Extraction of pillars on the retreat quite often throws large amounts of weight onto development workings. Weak shales in the roof and floor fail rapidly and the mine ribs slough to such an extent that mining often becomes very difficult. When this occurs efficiency goes down, costs go up, and the risk to men and machinery increases greatly. Difficult mining conditions in the early 60's forced a re-evaluation of all presently known mining techniques in bedded deposits. Many room-and-pillar mining plans' were compared with the system in use at that time, but none of them offered a better solution to the roof control problem. Longwall techniques were seriously considered, but machinery was not available that would cut the hard trona seam and still maintain the productivity obtained from room-and-pillar sections. Roof cones troy in the longwall methods appeared to be more satisfactory than that found in room-and--pillar techniques. It was therefore felt that a new technique using the longwall principle and based on rock mechanics should be tried rather than previously known pillaring methods.

Jan 1, 1966

By J. L. Sloughfy

The size distribution and mechanical strength of the iron ore pellet burden are important parameters in determining the efficiency of the blast furnace. From the very outset, the guiding principle of our pellet quality improvement program was that these parameters are also the key to improving productivity and cost control at the pellet plant. Recognizing the need for improved blast furnace burdens and for higher productivity and lower costs at the pellet plant, Carol Lake operators, in conjunction with the IOC Pellet Quality Committee, established the following goals for the improvement of Carol pellets: [ ]

Jan 1, 1981

By W. H. Jang

Recent research has demonstrated the utility of the FTIRIIRS adsorption density equation for in-situ study of surfactant adsorption phenomena at the surfaces of reactive internal reflection elements (IREs). The FTIR/IRS adsorption density equation is given by (formula) where r is the adsorption density, A/N is the absorbance per reflection, e is the integrated molar absorptivity, 4 is the bulk concentration of the surfactant, d. is the effective thickness, and dP is the depth of penetration. Previously, the validity of the adsorption density equation had been confirmed only from solution depletion measurements with high surface area powders. Now, FTIR/IRS studies of Langmuir-Blodgett (LB) monolayer films of fatty acid transferred to the surface of a calcium fluorite IRE .clearly validate the reliability of the FTIR/IRS adsorption density equation for quantitative analysis of surfactant adsorption. In addition, it was confirmed from the observed absorption band at 1550 cm-1 that the first monolayer of the transferred fatty acid chemisorbs at the surface of fluorite.

Jan 1, 1994

By C. V. Deutsch, O. Babak

A longstanding problem in geostatistics is that kriging usually assigns significantly greater weights to end samples in strings of data than it does to central samples. These weights are theoretically valid, but suboptimal estimates may result when there are geological trends in the variable near contacts, that is, large weights may be applied to samples that are systematically lower or higher than average. A number of ad-hoc corrections exist, each with pros and cons; none are fully automatic with a well-defined measure of optimality. A new method for estimation in a finite domain is proposed. This method is referred to as finite domain kriging. The method is based on kriging with a successively larger number of data. The total number of relevant data (n) is established, and then n kriging matrices are solved. The first matrix has the closest single data value (n-1 weights are set to zero); the second has the two closest data (n-2 weights are set to zero) and so on. The final matrix has all n data. The kriging weights used for estimation are the average of the weights from the n successive kriging runs. Each kriging run is optimal, yet with different smoothing and a different treatment of data at the end of the strings. The result is a set of weights that does not give undue influence to data values at the end of strings. The methodology is developed with examples. Cross validation shows that finite domain kriging outperforms conventional kriging.

Jan 1, 2009

By A. C. Smith, J. H. Rowland III

The Mine Improvement and New Emergency Response Act of 2006 (MINER Act) established a Technical study panel (the Panel) to provide recommendations on the utilization of belt air and new technology that may be available for increasing the fire resistance properties of conveyor belt used in underground coal mines. The Panel Report recommended use of the belt evaluation laboratory test (BELT) as the method for testing and approval of flame resistant conveyor belts used in underground coal mines. The research conducted to establish the correlation of the BELT with large-scale belt fire flammability tests was done using 91 - 107 cm (36- to 42-in.) wide conveyor belt. Due to today’s coal haulage capacity, the mining industry is using 183 cm (72 in.) and wider conveyor belts. The U.S. National Institute for Occupational Safety and Health (NIOSH) conducted a study to determine if the BELT will also qualify wider belts as fire resistant for use in underground coal mines. This paper describes the results of recent experiments comparing results from using the BELT and the large-scale tests for six different belts.

Jan 1, 2011

By Tom Ireland, Sumi Eratne

The approach to Risk Management during the procurement of major projects often has a significant outcome on the ultimate successful delivery of a project. The $NZ4.4B Auckland City Rail Link project is the largest and most complex transportation project yet undertaken in New Zealand. Risk management prior and during procurement was undertaken in accordance the ITIG Code of Practice for Risk Management of Tunnel Works (TCoP) and through the use of an Alliance Geotechnical Baseline report. This paper describes the measures taken during the procurement process to achieve certainty with respect to outcomes and minimise project risks whilst also achieving value for money. This included the use of cloud-based delivery of geotechnical data and 3-D geological models, reducing tendering costs and allowing a focus on risk mitigation measures during the tender rather than data management.

Jun 13, 2021

By Paul H. Johnson

A field investigation was undertaken to study some of the. chemical and hydrological aspects of leaching an impermeable copper sulfide waste dump. Samples, obtained by means of a Becker pneumatic drill from Kennecott's Chino "J" dump, near Silver City, New Mexico, were analyzed for their moisture and soluble-salt content, Fe +2 , Fe +3, Cu +2 , and H in their interstitial solutions and non-water - soluble Fe, Cu, and S in their rinsed residues. Conclusions were drawn from these data concerning the overall chemistry of impermeable-dump leaching and the hydrological characteristics of the dump.

Jan 1, 1970

By B. Mirabile, B. Stables

Standing support is often used in conjunction with underground retreat mining. Knowledge of the load-displacement behavior of a standing support, and loading induced by the mine opening is critical to proper support selection. The NIOSH STOP database contains load-displacement laboratory test data for most commonly used standing supports. Hydraulic load cells currently used to measure in-situ loading of standing supports have exhibited leakage under load, producing irregularities within the dataset. An improved hydraulic load cell eliminates leakage and produces more consistent data. INTRODUCTION A hydraulic load cell, more commonly known by “flat jack” or JackPack, is a device installed to determine the loading characteristics of roof to floor supports. These standing or roof to floor supports include, but are not limited to: pumpable cribs, cans, wooden cribs (4-point, 9-point, etc.), metal props, wood timbers, concrete donut cribs, and other variations of these standing supports. Flat jack devices have been used previously to determine the loading of such roof to floor supports. The most commonly used load cell for standing supports is based on a design intended for pre-stressing standing supports, not load measurement. These load cells are produced in South Africa, and can be formed into several different shapes depending on the applications (Barczak). Flat Jacks are manufactured in various shapes and sizes depending on the application, common shapes are square and round that are 25.4 mm (1.0 inch) thick when collapsed as shown in Figure 1. The sheet metal that makes up the bladder is comprised of 19 gauge or 1.11125 mm (0.04375 inch) thickness, the top and bottom pieces of sheet metal are resistance seam welded around the perimeter. There are two different ports installed on one of the bladder skin corners of the flat jacks; these ports allow a fluid to fill the unit and the other port has a relief valve. The fill port is comprised of a check valve. The pressure relief valve is located in the second port; preset to 1724 kPa (250 psi), pressure relief valve will keep the load cell from bursting. Bursting of these load cells typically causes a small tear in the metal skin allowing the fluid to leak out without a large catastrophic failure. The effective inflation range of these load cells is between 25.4 mm (1.0 inch) to 254.0 mm (10.0 inches) thick. Different types of fluids can inflate these load cells but the most common and easily accessible fluid for testing applications is water. Water pressure from the mine supply line can inflate these load cells to the desired load. Depending on the pre-stressing requirements a pneumatic powered pump, hydraulic pump or hand pump may be required to inflate the load cells.

Jan 1, 2019