Search Documents

By G. Sachs, L. J. Ebert, W. F. Brown

IT is a generally recognized fact that a steel quenched from the austenitic range and tempered to yield a structure composed of tempered martensite becomes increasingly more ductile with increasing tempering temperature. However, the conventional tensile test fails to yield any value that is sensitive to differences in behavior on tempering among the various low-alloy steels or among different heats of a particular steel. The notched impact bending test, on the other hand, has been recognized for a considerable length of time as capable of revealing differences in impact properties among various steels tempered to the same strength level (i.e., the same tensile strength in a conventional tensile test), However, this test is very complex and its significance has not been clarified up to the present time. Of its three characteristic features-the high speed, the notch, and the bending-the notch has been found by Davidenkov2 to be the most potent embrittling factor. Recent investigations on low-alloy steels3,4,7,8 have shown static notch-bar tensile tests to be more lucid and to evaluate the metal properties in much the same manner as impact tests, In an attempt to analyze the fundamental nature of this test,8 it was found possible to separate the effects of the two basic characteristics of the stress pattern introduced by the presence of a circumferential notch, the stress state and the high initial stress concentration at the notch bottom, The major conclusions drawn from these previous investigations were as follows: I. The magnitude of the triaxiality at fracture depends primarily on the initial notch depth. Its effect is a great reduction in the average ductility (contraction in area at fracture in the notched section) as compared with that observed in uniaxial tension, This triaxial stress state occurs at a point in the interior of the notch specimen, It determines the notch ductility if the notch is mild and/or the metal possesses a considerable ductility. On the contrary, brittle specimens probably fracture on the metal surface (at the notch bottom) at which point biaxial stress state is present, This biaxiality also considerably reduces the ductility of the metal. For small notch ductilities the notch strength and the notch ductility become very sensitive to embrittling factors, This is contrary to the behavior of the ductility values derived from a conventional tensile test, which are comparatively insensitive.

Jan 1, 1946

Discussion of the paper of G. K. Burgess and J. J. Crowe, presented at the New York Meeting, October, 1913, and printed in Bulletin No. 82, October, 1913, pp. 2537 to 2591. HENRY M. Howe, New York, N. Y. :-I think we can hardly rate the importance of the entry of the Bureau of Standards into our field. There is no body in the world that is better fitted to undertake this work than that Bureau, and it is work which really calls for the aid of some national organization. The skill and care with which this work has been done speaks for itself. It is very striking that within a very few months the distinguished English investigator, Professor Carpenter, of whom I spoke before, thought that he had disproved the existence of beta iron by proving that the A2 retardation which Professor Burgess has now demonstrated did not occur. Dr. Burgess's demonstration of the existence of. this retardation makes the existence of beta iron very probable, in my opinion. Osmond used to call beta iron " decipuum." You knew of its existence as you know of the existence of certain planets, only by the perturbation which it caused. Certain phenomena could not be explained, except by assuming the existence of a third allotropic form, beta iron. The evidence that you got was always evasive and susceptible of other explanations, except that which we have to-day, which it seems to me is not capable of other explanation. Professor Carpenter proceeded in the same way that Dr. Burgess has, by taking the heating and cooling curves of exceedingly pure iron, and thought that he had shown that there was no thermal change, no absorption or evolution of heat at the supposed A2 point, and hence that the A2 point did not exist. This he did by a piece of reasoning which I think seems to most of us rather surprising. That is to say, if of ten witnesses, three have seen a thing and seven have not, the evidence of the seven who have not is set aside, and that of the three who have seen stands. In Dr. Carpenter's own experiments under certain conditions he found the A2 change, the heat evolution., under certain others he did not. That is like the three witnesses who saw and the seven who did not see. You can arrange your test so that this change will not become visible or so that it is masked. But though an existent change can be masked a non-existent one cannot be shown. So that the reasoning seemed to me wholly fallacious.

Jan 12, 1913

By Marie L. V. Gayler

WITHOUT diffusion taking place in liquid metals and alloys, no castings could be made; it is therefore the most important factor affecting the structure of metals. Diffusion involves the interchange of atoms, a process which takes place during the life history of an ingot. In the liquid, atoms are in a state of high thermal agitation, but this thermal vibration is reduced in amplitude with falling temperature. When solidification sets in, the atoms arrange themselves on an ordered space lattice and the changes in structure which take place in the solid are due to the interchange of atoms on this space lattice. The rate of atomic interchange-e.g., of diffusion-is most rapid at temperatures close to the melting point and decelerates as the temperature is lowered. At room temperature, the rate of diffusion is practically negligible in most alloys, and any change in structure can only be brought about by using methods which will accelerate the rate of diffusion. The rate of diffusion depends on three factors (I) temperature; (2) concentration gradient and (3) activation energy. The growth of grains and particles in the solid alloy also depend on these factors and are therefore intimately associated with diffusion. The rate of homogenization in a cast alloy depends on several factors, such as: (I) rate of solidification, which involves grain and particle size which, in their turn, depend on diffusion: (2) the nature of the constituents; (3) the temperature interval between the melting point of the metal or alloy and the temperature at which it is being heat-treated. It is well known that coarse, cast structures are extremely difficult-if possible to homogenize, and the finer the grain size and particle size, the more readily solid solution will take place. The rate of diffusion depends, also, largely on the nature of the constituents; for instance, copper and magnesium form solid solutions with aluminum quite readily but nickel and iron do not; neither do certain intermetallic compounds, such as alpha and beta FeSi. Furthermore, the actual formation of intermetallic compounds may be a very slow process, particularly when they are formed in the solid state as equilibrium products. For example, ßFeSi is formed in the solid as the result of the reaction aFeSi + Al?ß FeSi. The particles of aFeSi become sur¬rounded with a reaction ring of ßßFeSi. This layer is formed as the result of diffusion of atoms taking place between the aluminum matrix and aFeSi. As the amount of ßFeSi surrounding the core of aFeSi increases the concentration gradient becomes low and so the rate of diffusion of atoms also decreases until it practically ceases. This occurs after a comparatively thin layer of ßFeSi has been formed. It follows that when intermetallic compounds of this type are formed in the solid, as the result of diffusion, it is generally impossible ever to attain equilibrium, since the forma-

Jan 1, 1944

By Colin Baker, G. C. Smith

Investigation of the initiation and propagation of ductile failure in OFHC copper was undertaken to determine the role of nonmetallic inclusions. The effect of inclusion initiated voids on the formation of the internal cavity and the final shear separation was studied by metallographic eranzination of strained test pieces. A strain anneal technique was used to enlarge the voids under uniaxial stress conditions to elinzinate triaxial stress effects. Measurements of void size us stress and strain were made to show the point at which void im'tiation begins and becomes an important factor in the deformation process. The work of separation of copper-cuprous oxide was determined to attempt to correlate the breakdown of the matrix inclusion interface with void initiation and propagation. The zloid shape and position relative to the tensile axis suggested an interface breakdown mechanisnz of initiation. Evidence is presented that shows a basic similarity between the central cavity propagation and the 45-deg shear portions of the failure. DUCTILE fracture has been studied by a number of workers1-lo and attention drawn to the importance of hard second phase particles in the initiation of the failure. Holes formed at the matrix-particle interface can elongate by plastic deformation and then subsequently expand sideways to link up and produce a major crack. This is usually observed first in the center of the macroscopically necked region of a test-piece where the hydrostatic stresses are at a maximum. As the crack spreads sideways towards the free surface of the specimen, well defined shear zones develop from the crack tip and the final separation is along a direction at approximately 45 deg to the stress axis. This shear failure may also be associated with voids formed adjacent to second phase particles. In this way a cup and cone type fracture is produced. The stage at which separation takes place between particles and the surrounding matrix has not been clearly identified. In addition, although researchers have dealt with anisotropy of tensile behavior" as a result of material fabrication variables, not much is known about the microstructural features of aniso-tropic behavior. In the present work evidence on these points is presented in relation to the behavior of copper containing second phase particles of cuprous oxide. I. MATERIALS AND PROCEDURES EMPLOYED The material used was +-in. diam or 2-in. sq cold-drawn OFHC copper bar which contained 0.6 pct by volume of cuprous oxide inclusions. These ranged in COLIN BAKER, Junior Member AIME, formerly at -mnF of Metallurgy, University of Cambridge, Cambridge, England, is presently Research Scientist Reynolds Metals Co., Richrnand, Va. G. C. SMITH, Member AIME, is Senior Lecturer, Department of Metallurgy, University of Cambridge. Manuscript submitted June 20, 1967. IMD size from approximately 1 to 6 p in length and 1 to 4 p in width. The shape was generally slightly ovoid. Tensile tests were made on specimens having a gage length of 2.5 cm and diameter of 0.643 cm. Metallographic examination was carried out by sectioning deformed and fractured specimens; in addition fracture surfaces were examined optically and with a scanning electron microscope. Some measurements of the work of separation between copper and cuprous oxide were made, using a sessile drop technique which was a modification of that used by Kingery and umenick." The best metallographic results were obtained by using a vibratory polisher, which minimized smearing of the surface. 11. RESULTS A) Initial Experiments. Specimens from the +-in. diam rod were annealed for 2 hr at 650°C in uacuo, at which temperature complete recrystallization occurred without any change in the form of the inclusion. They were then fractured at temperatures from -190" to 600°C. Cup and cone fractures were obtained at all temperatures from -196" to 400°C. With increase in temperature there was, however, a continuous increase in the extent of the central transverse area and a corresponding decrease in the shear portion of the fracture. Above 400°C, the fractures became intergranular. Sections of specimens tested below 400°C revealed extensive small voids which were always associated with inclusions. However, the voids only reached dimensions greater than the inclusion size in the region of the macroscopic neck, where they were many times longer. Lateral expansion was found only near the fracture surface of the test pieces. As observed by Puttick, the voids were either (a) triangular holes initiated in the direction of the tensile axis and elon-

Jan 1, 1969

By F. W. Schremp, J. W. Chittum, T. S. Arczynski

This paper describes a laboratory study of causes of external casing corrosion and the test work that led to the use of oxygen scavengers to prevent this attack. External casing failures are classified as water-line, casing-casing, collar and body failures. A corrosion mechanism based on principles of differential oxygen availability is developed that is consistent with facts known about each kind of failure. The field use of oxygen scavengers is depicted as a direct result of the laboratory study. A part of the paper is devoted to reporting on the field use of hydra-zine to control external casing corrosion. Results of field measurements made over a period of several years are presented as evidence of the efectiveness of the hydrazine treatment. The first conclusion reached is that the use of hydrazine materially reduces the cathodic protection requirements for treated wells. This result is interpreted to mean that a reduction is taking place in the amount of corrosion on the casing. Results indicate also that hydrazine shows its greatest usefulness within the first 12 to 18 months after a well is completed when pitting corrosion is likely to be most active. INTRODUCTION According to surveys sponsored by the National Association of Corrosion Engineers,' the cost of repairing casing leaks caused by external corrosion may exceed $4 million per year. In addition, well damage and lost production resulting from casing leaks probably costs the petroleum industry an additional $5 to $6 million per year. Concern about the cost of external casing corrosion led to an extensive laboratory study of factors causing this external corrosion and to the development of a new approach to its prevention. This paper presents a discussion of various causes of external casing corrosion, details of laboratory studies and the results of the field use of an oxygen scavenger in well cementing fluids to prevent the external corrosion of oil-string casing. Measurements on test wells over a period of several years show that cathodic-protection current requirements are greatly reduced when hydrazine is used in cementing mud. Reduction of current requirements can be interpreted to mean that removal of oxygen by hydrazine has greatly suppressed corrosion cells on the external surface of the casing and thereby, has reduced corrosion. To date, hydrazine has been used by the Standard Oil Co. of California in more than 200 well completions. KINDS OF CASING FAILURES A survey of a large number of casing leaks disclosed four types of external casing failures — water-line, casing-casing, collar and body failures. These types are identified largely by their location on the casing. Water-line failures are found just below the surface of water or mud in the casing annulus. Casing-casing failures occur on the oil string just below the shoe of the surface string. Collar failures are found in the threaded ends of casing joints where they are screwed into casing collars. Body failures may occur at any point on the body of a casing joint. Ex- amples of each kind of failure have some of the general characteristics that are shown in Fig. 1. Water-line failures usually result in the circumferential severance of an oil-string casing. The corrosive action causing a water-line failure usually is sharply defined and is limited to a short length of the casing. Casing-casing failures usually are accompanied by pitting corrosion distributed around the oil-string casing for distances up to 100-ft below the shoe of the surface string. Casing-casing failures may also sever the casing. Collar failures seem to start on the first thread at the bottom of recesses between collar and casing joint. Corrosion proceeds across the threads by what appears to be a normal pitting mechanism. Both casing and collar are severely attacked. Body failures are the result of highly localized pitting at any point on a casing wall. Besides the pit that perforates a casing, a large number of other pits usually are found along one side of the casing joint. The pits occasionally are filled with corrosion products consisting largely of oxides and sulfides.' Frequently, the mill scale is largely intact on the rest of the casing. Examination of a casing failure does not always reveal the cause of the failure. Frequently, the necessary details are destroyed when the failure occurs. For example, formation water flowing through a perforation at high velocity may enlarge the hole and destroy any remaining evidence of the cause of the failure. One way to obtain undistorted information about a failure is to study the nature of other pits on the casing in the vicinity of the failure. A study of such pits frequently suggests that they are characteristic of an attack resulting from the differential availability of molecular oxygen.

Jan 1, 1943

Jan 1, 1943

Jan 1, 1936

Jan 1, 1936

By Theodore Marvin

USE of airplanes to facilitate mining and petroleum operations has definitely left the "doubting Thomas" stage. As a matter of fact, front pages no longer record the novelty of this efficient arm of the mineral industry. We are now down to the facts basis. The recent aviation issue of Engineering and Mining Journal added - to our fund of knowledge on applications which the A.I.M.E. Aviation Committee is extensively adding to through its world-wide compilation of specific data. Another indication of the advance of flying in our. industries is the addition of regular aviation specialists to the staffs of various mining and petroleum companies, who function in the organization the same as do the metal

Jan 1, 1936

Jan 1, 1925

By C. S. Matthews, W. R. Strickler, M. Prats

To gain an insight into the deviations from normal behavior caused by dip. a mathematical study has been made of single-fluid five-spot floods in dipping reservoirs for flooding techniques likely to be employed in such cases. Streamline patterns and sweep eficiencies are computed for a number of different cases, and the results, where possible, are presented in graphical form. An increase in sweep efficiency can be obtained by moving the central injection well updip, and the opti~num position is found for several cases. The applicnhility of the results is discussed. INTRODUCTION Because of the growing importance of water flooding in California and in other locations where large angles of dip are quite common, it is important to know at least some of the effects of dip on the performance characteristics of water floods in such instances. In the past, only reservoirs having relatively mild dips have been wateflooded. Consequently, little is known today as to the effect of dip on the performance characteristics of a flooding operation from the point of view of field experience; and because of the complexity of the problem, little, if anything, has been done on the problem from the point of view of theory. There are two distinct aspects of the role played by gravity in a flooding operation. The first is that of the preferential segregation of the reservoir fluids at the time when the flood is to commence. The second is the role that it may play in affecting the performance of the reservoir during the course of the flooding operation. In this paper the reservoir is assumed to be filled with only one fluid, so that there is no preferential segregation of reservoir fluids at the commencement of the flood. Moreover, the injected and in-place fluids are assumed to have the same characteristics, so that in effect we consider only a single-fluid problem. Single-fluid results have been used as a guide in the past for predicting and interpreting the behavior of regular five-spot floods in horizontal reservoirs. It is thought that single-fluid results might likewise be used for five-spot patterns in dipping reservoirs as a norm to which the effects of the multifluid problems might he referred.* In confining our attention to the single-fluid case, we therefore do not consider the preferential segregation of injected water in the oil bank, or of the oil bank in the unflooded zone. Instead we consider the deviation from the behavior of a horizontal five-spot which is caused by use of flooding techniques (i.e., the flow potential pattern at injection and production wells) likely to be employed during flooding operations in dipping reservoirs. In other words, we consider effects which are caused by the pattern of injection and production well pressures which we choose to apply. Performance characteristics are given for the five-spot spacing pattern as a function of two parameters; one is the ratio of gravity head to potential difference bctwccn the high updip injection well and the low downdip producer of the same five-spot, denoted by Rg; the second is the orientation of the five-spot pat-

Jan 1, 1956

Jan 1, 1881

Jan 1, 1961

Jan 1, 1931

Jan 1, 1925

Jan 1, 1938

By Harold V. Pearce

(Chattanooga Meeting, October, 1908.) THE fire which occurred in the fall of 1906, at the works of the Boston & Colorado Smelting Co., Argo, Colo., destroyed entirely the gold- and silver-refinery of the plant; and in view of the development of modern practice in the refining of copper-mattes, etc., the management decided that it would be inadvisable to rebuild that part of the works for the continued use of the process which had been conducted therein for so many years as a metallurgical secret. This decision probably removes altogether from the sphere of practice the " Pearce " method for the separation of gold. At all events, it removes the business reasons which have prevented hitherto the publication of the principles involved. At the suggestion of Dr. Raymond, Secretary of the Institute, my father, Richard Pearce, the former manager of these works, has requested me to prepare a brief description of this process for the benefit of our members. Since I severed my connection with the Boston & Colorado Smelting Co. some time ago, I am indebted for some practical details to the present superintendent, Charles Rees, whose friendly assistance I would gratefully acknowledge. With regard to the history of the inception and development of this process by its inventor, Richard Pearce, I cannot do better than quote freely from his own notes and papers. HISTORY OF THE PEARCE PROCESS.' "In 1874 my entire time was directed to the improvements and additions to the plant at Black Hawk. The changes which I had made in the construction of the furnaces at Black Hawk proved so beneficial that I was requested to introduce the improvements at the branch works at Alma. These changes were carried out as speedily as possible, and proved of great advantage as compared with the old system. "The separation and refining of the gold from the matte now engaged my attention, and since previous experience in the treatment of gold-bearing matte and

Feb 1, 1909

By O. N. Cole, R. E. Davis, T. D. Brotherton

Pvfoperties of rubidium and cesium are compared with those of other alkali metals. Methods for the preparation of rubidium and cesium metal are reviewed briefly, ad hazards and safety precautions required in handling rubidium and cesium metal are described. SimPle methods for handling laboratory quantities of elemental rubidium ad cesium under oil and under argon are illustrated. CESIUM and rubidium were both discovered by Bunsen and Kirchoff in the years 1860 and 1861. Cesium was discovered while Bunsen and Kirchoff were making a spectrographic study of spring water from Durkheim, Germany. It was the first element discovered by this technique. The element was given the Latin name "caesius" for sky blue because of the color it imparted to flames. Elemental cesium was first prepared by Setterberg in 1881 through electrolysis of a molten mixture of cesium and barium cyanides.' In 1861, Bunsen and Mirchoff discovered rubidium while making a spectrographic study of the alkali content of lepidolite ore from Saxony. Two prominent dark red lines appeared in the spectrum and so the element was named "rubidius" or dark red. In 1861 Bunsen and Kirchoff first prepared elemental rubidium through the electrolysis of molten rubidium chl~ride.~ The alkali metals are very similar in their chemical and physical properties. They are the most active metals, and all exhibit a single oxidation state of one. They are so reactive that they are never found in nature in the elemental state. The reactivity of he metals increases with atomic number. Rubidiurn and cesium ignite spontaneously in air and react explosively with water. This extreme reactivity makes necessary special equipment and techniques for the safe preparation and use of the metals. The cation: of Group IA can be separated from the metallic cations of other groups with relative ease, but the separation of the individual alkali cations is much more difficult because of their close chemical similarity. This close chemical and physical similarity of alkali metals can be inferred from the atomic radii, oxidation numbers, and ioni-zation potentials shown in Table I. A difficult but the most practical physical method of separating the elemental alkali metals from one another is by distillation. Only lithium has a boiling point sufficiently far-removed from the boiling points of the other alkali metals to make this method of separation feasible without elaborate and expensive equipment. This method is not used, however, for lithium because it possesses sufficient chemical dissimilarity from the other alkalies for it to be separated relatively easily as lithium hydroxide monohydrate or as lithium carbonate. Francium, the last member of the group, has no known stable isotopes. The naturally occurring

Jan 1, 1962