Search Documents

By C. R. Boyd

The region to which I have the pleasure of calling your attention, though limited in area, is remarkable for the quantity and purity of its mineral deposits, and in these respects it would be difficult to find its equal anywhere. IRON ORES. The red and brown hematites, pipe ore, and semi-magnetites, from which is made in charcoal furnaces the highest quality of iron for car-wheels, extend through the counties of Giles, Montgomery, Pulaski, Wythe, Smyth, Washington, Bland, Tazewell, Russell, Scott, Lee, Floyd, Carroll, and Grayson, Virginia, and run over into Ashe County, North Carolina. One locality of semi-magnetite, in the centre of the great Giles County basin, has in sight, by actual measurement, 50,000 tons of ore, which, according to Prof. Fesquet, contains 69.74 per cent. of iron and no phosphorus. In the great brown-ore belt, which passes through the counties of Montgomery, Pulaski, Wythe, Smyth, and Washington, there is an extraordinary deposit of more than a million tons. A small section of this very long vein, on Cripple Creek, in the County of Wythe, yields an ore which, analyzed by Mr. James Aumann, gave the following results: Metallic iron,........58.15 Water,.........12 96 Alumina,........2.32 Silica,.........1.09 Phosphorus,.. none. At one point towards the western end of Red Land Mountain, in Pulaski County, New River section, I measured a body of ore in this belt which will yield, to a depth of 150 feet, over 8,000,000 tons, and the deposit extends far below the 150 feet measured at the upper part. Again, at Rich Hill, near the mouth of Reed Island Creek, these veins show extraordinary surface development, giving an ore of very great purity. At numerous places, also, in the counties of Giles, Bland, Tazewell, Russell, Scott, Wise, and Lee, these brown and red iron ores are exposed in such vast quantities as to baffle both description and measurement. That of Chestnut Flat, in Giles County, back or west of the Angel's Rest Mountain, is an easily reducible ore, blood-red when crushed, of which there are fully 300,000 tons in sight. Its analysis is as follows :

Jan 1, 1880

By C. R. Boyd

THE region to which I have the pleasure of calling your attention, though limited in area, is remarkable for the quantity and purity of its mineral deposits, and in these respects it would be difficult to find its equal anywhere. IRON ORES. The red and brown hematites, pipe ore, and semi-magnetites, from which is made in charcoal furnaces the highest quality of iron for car-wheels, extend through the counties of Giles, Montgomery, Pulaski, Wythe, Smyth, Washington, Bland, Tazewell, Russell, Scott, Lee, Floyd, Carroll, and Grayson, Virginia, and run over into Ashe County, North Carolina. One locality of semi-magnetite, in the centre of the great Giles County basin, has in sight, by actual measurement, 50,000 tons of ore, which, according to Prof. Fesquet, contains 69.74 per cent. of iron and no phosphorus. In the great brown-ore belt, which passes through the counties of Montgomery, Pulaski, Wythe, Smyth, and Washington, there is an extraordinary deposit of more than a million tons. A small section of this very long vein, on Cripple Creek, in the County of Wythe, yields an ore which, analyzed by Mr. James Aumann, gave the following results: Metallic iron, - 58.15 Water, - 12 96 Alumina, - 2.32 Silica, - 1.09 Phosphorus, - none. At one point towards the western end of Red Land Mountain, in Pulaski County, New River section, I measured a body of ore in this belt which will yield, to a depth of 150 feet, over 8,000,000 tons, and the deposit extends far below the 150 feet measured at the upper part. Again, at Rich Hill, near the mouth of Reed Island Creek, these veins show extraordinary surface development, giving an ore of very great purity. At numerous places, also, in the counties of Giles, Bland, Tazewell, Russell, Scott, Wise, and Lee, these brown and red iron ores are exposed in such vast quantities as to baffle both description and measurement. That of Chestnut Flat, in Giles County, back or west of the Angel's Rest Mountain, is an easily reducible ore, blood-red when crushed, of which there are fully 300,000 tons in sight. Its analysis is as follows

Jan 1, 1880

By Schlumberger, C

IN the search for practical geological problems amenable to solution by the potential methods, the geophysicist is led to study mathematically various theoretical cases. In these idealistic discussions, the media under consideration are generally supposed to be homogeneous and iso-tropic. The geophysicist, of course, realizes perfectly that these condi-tions do not occur in their entirety in reality. However, the assumptions made are justified, because very often they are necessary in order to render possible an exhaustive study of a given problem, which otherwise would be too complicated, and would not lend itself to a complete mathe-matical analysis. Of the above two assumptions, that concerning the homogeneity of a given geological formation is satisfactorily realized except in so far as isotropy is concerned, since this property is not often encountered in practice. As a consequence, it is very desirable for the geophysicist to have quite an extensive knowledge of the properties of anisotropic forma-tions, and of the laws that govern the propagation of electric current therein. With such principles in mind, he will be able to decide whether the conclusions arrived at in simple, isotropic conditions are still correct in more complex cases, or in what way they must be modified or adapted in order to constitute a sound basis for the interpretation of the results obtained in anisotropic media. On the other hand, the fact that in anisotropic formations themobility of the ions is greater along the strike than perpendicular thereto can be utilized for determining the direction of the dip by induc-tion measurements. We therefore propose to study in three successive chapters the following points: 1. Propagation of the electric current in anisotropic media. 2. Some consequences of the anisotropy of geological formations with reference to the surface electrical measurements, and their interpretation. 3. Determination of the direction of the dip of anisotropic formations by surface induction measurements.

Jan 1, 1933

By C. H. Li, R. J. Stokes, S. H. Bendel, J. A. Sartell, T. L. Johnston

The mechanism of the oxidation of high-purity copper has been studied at temperatures from 500° to 981°C employing gravimetric, high-temperature microscopic and inert marker techniques. An investigation of the adhesion of copper oxides was also made. The oxidation of copper is found to be parabolic at all temperatures. It is concluded that the controlling mechanism is the outward diffusion of CU+ ions through the Cu2O layer, but the mechanism of diffusion is modified by the state of compressive stress in the oxide layer at the oxidation temperature. At temperatures below the transition from elastic to plastic behavior of Cu2O the growth stresses reach a value sufficiently high to cause CuO whiskers to be extruded. The extrusion of whiskers results in the injection of a large number of vacancies into the CuO. The Cu20 layer grows by the advance of the CuzO/CuO interface into vacancy-rich CuO. Since there is an adequate supply of non -thermally created vacancies, the activation energy for oxidation is that required to move the Cu+ ion through the appropriate saddle point to a neighboring vacancy, which has been determined to be 20,000 cal per mole. At temperatures at which the Cu20 can deform plastically the stresses are never high enough to cause whiskers to form. thus vacancies must be supplied by themal activation and as a result the activation energy increases to 40.000 cal per mole. ALTHOUGH extensive studies of the oxidation kinetics of pure copper have been made in the past. the mechanism has received relatively little attention. As a result, certain features of the kinetic data have not been satisfactorily explained' For example, several workers1,2 have reported that the activation energy for oxidation in the range from 500° to 700° C was about 20,000 cal per mole whereas that above

Jan 1, 1960

By N. S. Stoloff, J. N. Mushovic

Age hardening response of a Mg-Th-Zr alloy has been studied at temperatures in the range 60° to 450°C. Transmission microscopy revealed clustering of thorium atoms at low aging temperatures, supporting a previous report of GP zone formation. Peak strengthening, which is observed at 325°C, is due to the formation of a coherent, ordered, DO19 type superlattice structure, of Hobable composition Mg3Th, as plates parallel to the matrix prism planes. These plates later reveal a Laves phase structure of composition Mg2Th. The equilibrium Mg4Th phase begins to precipitate in two different forms at an early stage, competitively with the Mg2Th plates. RECENT work on the Mg-Th system indicated that, unlike most magnesium-base alloys, complex precipitation phenomena may be occurring. The partial phase diagram of the Mg-Th system indicates that an equilibrium phase, Mg5Th, is the sole intermediate phase.' sturkey,' however, has reported, using X-ray and electron diffraction techniques, that a metastable fcc Laves phase, Mg2Th, precedes the formation of the equilibrium compound, which he identified as closer in composition to Mg4Th. Murakami et al.3 reported that the equilibrium phase precipitates preferentially on grain boundaries and dislocations in a Mg-1.7 wt pct Th alloy; Kent and Kelly4 aged a more dilute alloy, Mg-0.5 wt pct Th, for 4 days at 220°C and found similar results. In addition, they reported that a platelike phase with a structure close to that of the magnesium matrix forms perpendicular to the basal plane and is probably ordered. Research on a Mg-4 wt pct Th alloy by electrical resistance measurements and transmission electron microscopy has suggested that GP zones may form at low aging temperatures.3 However, the electron micrographs purporting to show this phenomenon were not conclusive. In view of the fragmentary evidence concerning the nature of the precipitation processes in the various Mg-Th alloys, an aging study was undertaken to clarify the characteristics of the various precipitates which form and to correlate the mechanical properties of the system with the direct precipitate-dislocation interactions. The latter results are presented elsewhere.' The purpose of this paper is, therefore, to discuss the precipitation sequence in this system. EXPERIMENTAL PROCEDURE Sheet stock (0.060 and 0.010 in. thick) of a commercial Mg-3.93 wt pct Th-0.42 wt pct Zr alloy (designated HK3lA) similar to that studied by sturkey2 was supplied through the courtesy of Dr. S. L. Couling of Dow Metal Products Co. Zirconium does not enter into any precipitation reactions,' but is present primarily as a grain refiner. The alloy was chill cast, warm rolled to 0.090 in. thick stock, and then finally reduced by a combination of hot and cold rolling. The alloy chemistry is given in Table I. This material was solution treated at 580°C for 4 hr in a dry CO2 atmosphere, and then water quenched. Material in this condition was fairly clear of precipitate particles and was fully recrystallized. Aging at temperatures less than 200°C was accomplished by immersing the alloy in a silicone oil bath; for higher temperatures, aging was done in a salt pot. Age hardening treatments were conducted at 60°, 80°, 105°, 135°, 160°, 250°, 325°, 350°, and 450°C for times ranging from 5 min to 400 hr. Hardness tests were performed on chemically polished 0.060-in.-thick blanks of solution treated material which were aged at the various temperatures for increasing lengths of time. For aging temperatures above 150°C the Rockwell Superficial 30T scale was employed, while samples hardened at temperatures below 150°C were monitored with the 45T scale. Each data point consists of at least three separate readings. Yield stresses also were measured at room temperature on both 0.060 and 0.010 in. sheet specimens aged at 325°C. The aged foils were thinned by the window method in a solution of 80 pct absolute alcohol and 20 pct concentrated perchloric acid (70 pct) maintained at 0°C. A stainless steel cathode was used and the applied voltage was 10 to 15 v. Thinned samples were rinsed in distilled water and pure methanol. After the me-thanol rinse the thin foils were quickly dried between filter paper. Foils prepared by the above method were examined in a Hitachi HU11B electron microscope operating at 100 kv. RESULTS A) Hardness. The hardness data are depicted in Figs. 1 and 2. Peak strengthening occurs at 325°C after aging about 6 min, see Fig. 1. Significant strengthening is achieved also at 350°C, but aging at 450°C produces only softening. The stepped curve at 250°C indicates that a complicated precipitation process may be occurring at that temperature. Fig. 2 suggests that at least two hardening mechanisms exist since the lowest temperature hardness peaks are displaced to the left of the peaks obtained at 135° and 105°C. A great deal of scatter is observed at long times in all cases due to magnesium surface degradation caused by the silicone oil bath. B) Identification of the Strengthening Precipitates. The structure formed atlowagingtemperatures (c10O°C) was not clearly resolvable by transmission microscopy. The only bright-field evidence for a change in structure was a mottled appearance which could be observed at extinction contours, as shown in Fig. 3(a), and the disappearance of this effect when dislocations produced under the influence of the electron beam passed through the matrix, as noted in

Jan 1, 1970

By R. R. Jones, R. W. Kraft

Zn-Mg2Znn eutectic alloys nzay freeze willr either rodlike or lanzellar rnorphology. Alloys with slighlly more than /he eutectic arrzount of rnagnesillrn usually contain three-cnned dendrjles of MgzZnll in a eutec-lic ttlulris. All three morphologies haue the same cryslallographic orientution relationship: (0UOl) zn - 11 (111) Mg2Znll and (2310)Zn 11(101) Mg2Znll, but u3ith different prej-erred groulth direclions. The lurnellae lo rods transifion in con/rolled ingols qf euleclic cotnposition occurs because lhe large kinelic undercooling due to MgzZnll minirrzizes /he ejj-ecl of the solid-solid inlerface energy. The eutectic morphology is influenced by the presence of lhree-nned dendrites 0-f MgzZn11 which may conlrol /he rricroslrccture by acting as nuclealion sites. In recent years there has been much interest in eutectic solidification and several theories have been proposed. One of the confusing factors is the existence of various morphologies in which the solidified phases may form. The lamellar microstructure seems to be most common in metal eutectics, and it has been claimed' that all regular eutectics should be lamellar if sufficiently pure. However, there still remain eutectic alloys which are not lamellar or which change their morphology as a function of growth conditions. The eutectic between zinc and the intermetallic phase Mg2Znll was chosen for this investigation because it has been found to solidify in more than one morphology. The diagram in anssen' locates the eutectic point at 3.0 wt pct Mg and 367°C. lliott gives 364°C as the eutectic temperature, leaving the phase compositions unaltered. Since the growth conditions determine the micro-structure of the solidified alloy, the factors controlling the transition from one morphology to another could be studied. The lamellae to rods transition is of particular interest. PROCEDURE Alloys were prepared from carefully weighed portions of 99.999 pct Zn and 99.97 pct Mg by melting in Pyrex containers under argon and casting into graphite boats. The resulting ingots were remelted under argon and solidified unidirectionally in a horizontal tube furnace at growth rates ranging from 2.0 to more than 50 cm per hr under a temperature gradient, measured over a 5-cm length, of 9" to 14°C per cm. The solid-liquid interface appeared to be planar at all growth rates although no attempt was made to confirm this by decantation or quenching. A few ingots were allowed to freeze uncontrolled. Most alloys were of the nominal eutectic composition, 3.0 wt pct Mg according to Hansen2 and lliott, but some contained as much as 3.35 wt pct Mg. Chemical analyses were not run since metallographic examination confirmed that the desired composition was achieved. Specimens were cut from the middle portion of the ingot normal to the growth axis, polished mechanically, and etched with 2 pct Nital. Suitable areas were selected for the determination of crystallographic orientation relationships by a tiontechniqueof described previously by one of the authors.4 The (2310) planes of zinc and the (8701, {944}? (1032) planes of Mg2Znll were found suitable for orientation determination; experimental error was on the order of 2 or 3 deg. RESULTS Three different morphologies were found in the unidirectionally solidified alloys: lamellar eutectic, rod-like eutectic, and a structure whose most predominant characteristic was the presence of three-vaned (cellular) dendrites of Mg2Znll. These dendrites were only found in alloys with more than the eutectic amount of magnesium. In some ingots fine hexagonal needles of Mg2Znll surrounding a core of MgZn2 were observed. They were probably due to incomplete alloying and seemed to have no effect on the eutectic morphology. In addition hexagonal spirals like those discussed by Fullman and wood5 and Hunt and acksonh ere observed in some ingots frozen without directional control. Both MgZZn,, and MgZnz were detected by X-ray diffraction in these alloys. Since the morphology could not be grown unidirectionally and no characteristic orientation relationship between the phases was found, further study was limited to the lamellar: rodlike, and three-vaned dendrite morphologies. Alloys of Eutectic Composition, No Dendrites. The mcrostructures of allovs with no three-vaned dendrites were either lamellar or rodlike depending on the growth rate. At rates below 10 cm per hr the morphology was lamellar, consisting of two sets of parallel plates intersecting at about 54 deg like the Mg-MgzSn eutectic described by raft.7 At growth rates faster than 14 cm per hr the microstructure showed rods of zinc in a matrix of MgnZnll, while intermediate rates yielded mixtures of rods and lamellae in small groups. The lamellar "grains" were often several millimeters in cross section, but contained small irregular areas which divided each grain into perfect islands 100 or 200 p in diam. Lamellae were parallel to each other throughout the grain in spite of these defects in the structure, Fig. 1. Rods, on the other hand, could only be produced in small groups arranged like fish scales and separated by irregular areas of appreciable thickness, Fig. 2. Alloys Not of Eutectic Composition, With Dendrites. In alloys with 3.1 to 3.35 wt pct ME,-. three-vaned dendrites bf MgzZnll were usually found surrounded by eutectic. At growth rates slower than about 10 cm per hr the dendrites were separated from each other by small areas of both lamellar and rod eutectic, Fig. 3.

Jan 1, 1969

By Harry C. Swanson

TRANSPORTING concrete from mixer to forms has always been a problem. Twenty-five years ago this task was generally accomplished by means of wheelbarrow or concrete buggy. On large dam jobs, as the number of these projects increased, the gantry crane or highline came into use. Today several methods of handling concrete are employed on smaller surface construction jobs, for example, transit-mix trucks or dumpcrete trucks, which have crawler cranes with buckets for placing concrete into forms. In 1944, during early stages of developing Mather mine A shaft, several large underground concrete jobs were necessary. At this time the Cleveland-Cliffs Iron Co, purchased the first pump-crete machine, introduced by the Chain Belt Co. of Milwaukee. The machine was used to pour approximately 200 cu yd of concrete for a dam, or bulkhead, located 400 ft from the shaft. Concrete was mixed on surface, lowered down the shaft 1000 ft in a 2-cu yd bucket hung under one skip, spouted into the bowl of the pumpcrete machine from the bucket, and pumped directly into the forms. Since the day of the first pipeline concrete in 1944 to the present time, other equipment and other methods have been developed to permit transportation of concrete by pipeline through vertical and horizontal distances totaling 1 mile from mixer to forms. Much of the efficiency in present handling of underground concrete can be credited to the Bethlehem Cornwall mines, where concrete was transported through 6-in. pipe for great distances down an inclined shaft and along levels into forms.' During initial development of Mather mine B shaft, with concrete work under way on two or more levels at one time, the pneumatic concrete placer, Fig. 1, was selected as best adapted for underground concrete transportation. The 3/4-cu yd pneumatic placer is a small machine readily moved from one location in the mine to another. It can be equipped with two sets of mine car wheels, which will permit moving on regular mine tracks. It is therefore possible to send concrete through the pipe at great velocity; the pipeline is clean after each shot except for the film of cement adhering to the inside. With the proper slump in the concrete, it is possible to shoot concrete 2000 ft with this machine, using the mine supply of compressed air at 95 psi. This equipment was first used at Mather mine B shaft to concrete slusher drifts, Figs. 2 and 3, and finger raises located about 2000 ft from the shaft. In several instances there were bends into crosscuts and up vertical distances into the forms. For the first pours two placers were used. The first was located near the shaft where the concrete could be spouted into it from a 2-cu yd concrete bucket on the cage. The second was set on the side of the drift at a point approximately 1500 ft from the shaft. The concrete was shot directly into the second placer from the first unit and from the second machine directly into the forms. After completion of several pours with the two machines, a trial pour with only one placer located at the shaft proved that the second placer could be eliminated. Since then all pours have been successfully completed with only one placer underground. As production of iron ore from the mine increased and the development program expanded, use of the cage for handling mine supplies and concrete became a major problem. This brought about the first attempt at shooting concrete vertically down the shaft for 2600 ft. A 6-in. pipeline with victaulic couplings installed during shaft sinking was used for the trial. One placer was set on surface 250 ft from the collar of the shaft so concrete could be spouted directly into it from the mixer. This machine shot the concrete 250 ft horizontally on surface to the shaft, 2600 ft vertically down the shaft, and 100 ft horizontally into the second placer located near the rib of the shaft station or plat. The second machine shot the batch into the forms, about 2000 ft. Total distance horizontally and vertically was 4800 ft. The entire time cycle for a ¾-cu yd batch of concrete from the mixer on surface to the forms underground totaled about 5 min. During the past two years the two-placer method from the mixer on surface to the forms underground has proved a very efficient means of transporting underground concrete. Advantages of using pipeline concrete are as follows: 1—Interference with normal mining operation is eliminated. When the cage, skips, mine cars, or mine openings are used for transporting concrete and materials used for making concrete, mine operation suffers in one way or another.

Jan 1, 1955

By P. Schwarzkopf, J. H. Brophy

A modification of the Mendenhall wedge blackbody1 has been used to determine solidus temperatures and to anneal alloys in the tantalum-rhenium binary system. The technique has proven to be simple and accurate with modest power requirements. For temperatures up to 2800° C a piece of 10-mil tantalum sheet was folded double and formed as shown in Fig. 1. The middle of the resulting ribbon filament was a cylindrical-shaped crucible with less than a 1/8-in. opening. After inserting a specimen in the cavity, the filament was clamped between molybdenum electrodes in a high vacuum chamber. A representative filament 2 in. long and % in. deep was heated to 2800°C with a current of 700 amp at 4 v. The specimen temperature was determined by sighting into the cavity with a Leeds and Northrup optical pyrometer. The twisted filament shape was necessary to avoid serious geometric changes during thermal expansion. For temperatures between 2800" and 3000°C a 4-mil tungsten filament was employed. To facilitate fabrication it was warm-folded, and a twisted segment of 10-mil tantalum was used to support one end to absorb thermal expansion. This element assembly required about 700 amp at 10 v to reach 3000°C. Two geometric modifications of the filament were helpful for solidus temperature determinations. A shallow chamber, with depth to opening ratio of 3 to 1, permitted direct observation of the specimen through the optical pyrometer. The fact that the specimen was visible permitted the melting point to be determined when sharp features on the specimen surface became rounded; it also indicated that blackbody conditions did not prevail. By standardizing against the melting point of molybdenum, the observed melting temperature was corrected by the following form of Wien's Law: in which T is the true temperature, To is the observed temperature, and K is a constant characteristic of the filament geometry and determined experimentally for the molybdenum standard. The resulting corrected melting point for each alloy served as a reference temperature for the second more precise filament geometry. With a 6 to 1 depth to opening ratio, the specimen was indistinguishable from the filament interior, indicating good blackbody conditions. Using this technique, a series of specimens was isothermally treated at temperatures above and below the corrected direct reading. Incipient melting was detected by visual or micrographic examination of the specimen after cooling. This procedure was checked with specimens of pure chromium, molybdenum, and tantalum. Table I represents the values obtained, together with the solidus temperatures in the tantalum-rhenium binary system determined by the same technique. The alloy specimens were approximately 1/8 in. in diam. They were pieces of 10-g buttons melted four times in a nonconsumable tungsten electrode arc furnace on a water cooled copper hearth in 2/3 atmos of titanium gettered helium. Several sources of error are possible in such temperature measurements. Within the accuracy of the pyrometer no gradients were detectable near the specimen, and element distortion was virtually eliminated by twisting the tantalum. Compensation was made for the 1/8-in. sight glass by inserting several identical thicknesses and extrapolating to zero thickness. As a result an additional 10°C correction was added to all observations in the temperature range of 2500" to 3000°C. The principal source of error was then in the operation of the

Jan 1, 1961

By D. L. Garthwaite, F. M. Stewart, F. K. Krebill

Pressure has been maintained in the Elk Basin Ten-deep reservoir since the initiation of inert gas injection in Sept., 1949. Oil is being produced under conditions favorable for gravity drainage, including high angle of dip, appreciable structural closure, and fairly good per~neability. Results being obtained are high per cent recovery of oil-in-place, sustained field productivity, reduced operating problems, and recovery of plant products. The high recovery has been calculated by alpplication of the gravity drainage theory described in an earlier AIME paper.' It is also confirmed from field performance by comparing nil recovery to date with gas cap spuce voided. GENERAL INFORMATION The Elk Basin field lies in Park County, Wyo., and Carbon County, Mont., approximately 50 miles east of Yellowstone Park. Located at the northern end of the Big Horn Basin. the field is situated on an elongated asymmetrical anticline (Fig. 1). The pressure maintenance project covered by this paper involves the Embar-Tensleep reservoir in this multi-pay field. Discovered in Nov., 1942, it has a proved productive area of over 6,300 acres. It consists of the 210-ft thick Tensleep sandstone of Pennsylvanian Age overlain by 40 ft of Embar dolomite of Permian Age. The two formations apparently are in communication with each other and are produced as a common source of supply. As 98 per cent of the reserves are contained in the Tensleep sandFtone, in this paper the Embar-Tensleep reservoir will he called simply the Tensleep. The reservoir is found at an average depth of 4,900 it, is approximately 7 miles long and 2 miles wide, and has a maximum oil productive closure of 2,330 ft. The strata dip an average of 21" on the west flank and 45" on the east. There are presently 132 Tensleep wells in the field drilled on 40-acre spacing; of these, 17 are shut in because of high gas-oil ratio (GOR) and eight are gas injection wells. Rock characteristics and related information for the pay section follow: Porosity, avg 10.7 per cent Permeability (air) from cores, avg 118 mds Permeability from PI'S 91 mds Connate water, avg 8 per cent Initial pressure (-400 ft) 2,234 psia Pressure April 1954 (-400 ft) 1.327 psia At high structural positions much of the better sandstone has connate water content of only 2 to 5 per cent as indicated by the coring of wells with oil in nearby Tensleep fields. In special imbibition tests, samples readily imbibed oil but repelled water. In tests on crushed samples, the sand grains rapidly settled in oil and carbon tetrachloride but formed a stable unsinking floc in water. This information indicates that the Tensleep sand is preferentially oil wet. The oil produced averages 29' API gravity and has a high sulfur content. Extensive sampling and testing have established the fact that characteristics of reservoir oil in this field vary greatly with structure, see Fig. 2. Additional detail on the variation of oil characteristics with structure at Elk Basin may be found in Reference 2. At original reservoir pressure the oil was undersatu-rated with gas, the bubble point being 1,250 psi at the crest but only 500 psi at the lowest elevation sampled. As noted on Fig. 2, other fluid properties—reservoir volume factor. solution ratio, gravity, viscosity, and hydrogen sulfide content—likewise vary greatly. These variations complicate mathematical analysis, for it is necessary to average these characteristics in order to enter them into reservoir engineering expressions. To further complicate analysis, sand-face pressure also varies greatly because of the increase in fluid head down structure. As an approximation, average properties under initial conditions may be read from Fig. 2 at the -450-ft elevation.

Jan 1, 1956

By J. Szekely, Robert J. Fisher

A formulation is Presented and solutions are given for the problem of transient heat conduction in a sphere that undergoes a spatially uniform radiative heat exchange with its environment. The solutions were obtained by the numerical integration of the appropriate Partial differential equation and are Presented in a graphical form by Plotting a dimensionless average temperature against the Fourier number with the radiation number as a paranreter, for various initial sphere and environment temperatures. In addition to these numerical results asymptotic analytical solutions are also given. PROBLEMS involving the transient heating or cooling of droplets and particles frequently arise and are of importance in metallurgical operations. Spray refining, vacuum degassing, high-temperature gas-solid reaction systems, and pebble heaters are but few of the numerous examples that may be quoted. The practical interest in these problems from a design or operational point of view is to evaluate the change in the particle temperature with the time given its physical properties, initial temperature, and that of the environment. At the high temperatures encountered the principal mode of heat transfer between the particles and their environment is by thermal radiation; in case of vacuum degassing due to the very low thermal conductivity of the gas space the convec-tive components are negligible and radiation is the only heat transfer mechanism. Although much work has been done on transient heat conduction problems, the special class mentioned here, in which thermal radiation is specified at the bounding surface, received little attention to date. One contributory factor to this situation may be the nonlinearity of the radiation term in temperature, which in general precludes the use of analytical techniques and requires numerical or analog solution of the appropriate differential equations. In fact the only solutions of general nature that are available at present pertain to semi-infinite media and slabs.'-3 The work on which the paper reports forms part of a program aimed at the theoretical and experimental study of transient radiative heat exchange between particles and their environment. The purpose of the present paper is to develop a formulation and solutions to the problem of transient heat conduction in a sphere that undergoes a spatially uniform radiative heat exchange with its surroundings. The solutions, obtained by the numerical integration of the appropriate differential equations, will be presented graphically, by plotting dimensionless parame- ters covering the range of variables relevant to metallurgical interests, thus affording a ready reference for design calculations. In addition to these results, approximate analytical solutions are also given which represent asymptotes, corresponding to extreme values of the variables mentioned. FORMULATION Consider a spherical particle of radius, a, initially at uniform temperature, Ti (T measured on the absolute scale), having a thermal conductivity, k, density, , specific heat, C, and thermal diffusivity, a. At time = 0 let this particle be exposed to an environment which is at a temperature T, and subsequently let there be a purely radiative heat exchange between the particle and the environment resulting in a spatially uniform heat flux at the surface. If in addition to the above we make the assumptions that the sphere is a gray body radiator, homogeneous, isotropic, and opaque, and that the physical properties are independent of temperature, conservation of heat in the sphere may be written as follows: The boundary condition contained in Eq. [3] states that the initial temperature of the sphere is considered uniform, equalling Ti, whereas Eq. [4] is readily obtained from symmetry considerations. Eq. [5] expresses the continuity of the heat flux at the surface of the sphere, or in other words the condition that the rate of heat exchange between the sur-

Jan 1, 1969

By W. A. Sweet

THE furnace I am now about to describe was designed to obtain and maintain very high temperature. Knowing the cost of the gas furnace that was in successful operation here and abroad, I approached the subject with some misgivings as to my ability to attain anything like success, or even to reach a point of advancement. There seemed to be a field for a furnace of moderate cost for small mills, or where a particular heat was wanted, but the work was not enough to warrant the outlay necessary to build any gas furnace yet brought before the public. The section, Plate V, represents the furnace as I now build it for

Jan 1, 1875

By Henry J. Welge

The approximate methods which are now in use for calculating oil displacement from reservoirs by gas-cycling or gravity-drainage at constant gas pressure, or by water flooding, make use of fundamental relationships derived by Leverett' and Buckley and Leverett.2 The mathematical equations needed are derived by applying Darcy's law to the flowing phases, and by material balance considerations. ln general, any treatment of this type gives. for any particular exploitation time considered, a plot of oil saturation against distance in the reser-voir. The oil recovery must then be obtained by integrating in some manner the area under the plot. A useful analytical method has been derived for computing the average saturation, and hence the oil recovery. Use of this method simplifies the calculations because it makes unnecessary any numerical integrations. and even the saturation distribution plots are not needed. A further advantage of the method is that knowledge of the relative permeabilities is required only for a limited and intermediate saturation range. In both the Buckley and Leverett method and the method discussed here, a linear sand section is assumed, and in the case of gas drive the gas pressure is assumed sufficiently constant both with respect to reservoir position and time so that changes in gas density. solubility, or reservoir volume factor are negligiklle. Thus, the exploitation contemplates oil displacement as by an immiscible phase. Examples are given to illustrate how the new method can be used. INTRODUCTION AND THEORETICAL BACKGROUND This paper treats a simplified method for computing oil recovery when the oil is displaced, from the reservoir sand by a fluid which, within the limits of accuracy desired, can be assumed to be incompressible and immiscible with the oil. The method makes use of two basic relations originally developed for the case of water displacing oil. However, the case of gas displacing oil saturated with gas at a constant (or nearly constant) pressure may also be considered a displacement by an immiscible fluid. This is possible for the reason that the concentration of the gas in the oil never changes if tile pressure is fixed. consequently, any additional free gas must remain undissolved in the oil, and so must act essentially as an immiscible phase. For convenience, the cape of gas drive will be considered first. Both of the two basic relations needed refer to a linear reservoir, or one which may be somewhat idealized so that a constant cross-section is exposed to fluid flow. Further, the displacing phase is injected at one end, or face; of the reservoir, while the produced fluids are understood to emerge at one point only. which is the opposite face of the reservoir. As indicated in Fig. 1, the reservoir may he inclined by some angle 8. The first of the required equations may be derived by applying Darcy's law to both displacing and displaced phases, and subtracting the two equations. The result for water drive has been given previously, as Equation (13) of the reference by

Jan 1, 1952

By W. D. Robertson

A considerable quantity of experimental data is available on the effect of time, temperature, work-hardening and composition on the mechanical properties and corrosion resistance of aluminum alloys. There is, however, little unity of purpose or generality in most of the studies and, because the number of variables is large, the results often are not applicable to the problems that arise in practice. Furthermore, the customary expression of the effect of different variables as separate curves or as three-dimensional diagrams with time, temperature and the dependent variables as coordinates, renders the task of selecting the optimum time and temperature of precipitation treatment, with respect to their simultaneous but unequal etfect on the various properties, exceedingly difficult. The introduction of precipitation treatments to raise the yield strength of 24s-type alloys has created a need for a method of correlating and summarizing the effect of time and temperature on the mechanical properties and susceptibility to inter-crystalline corrosion. Correlation is particularly desirable because the choice of time and temperature is of necessity a compromise to achieve the best possible combination of properties, and the optimum conditions cannot he accurately specified unless the data are in a form in which the alternatives can be readily compared. Therefore, the work described here was undertaken to find a common relationship that would be capable of expressing the effect of precipitation time and temperature on the various properties and by means of which the relative effects could be correlated and their interpretation facilitated. Review of Previous Work In connection with an investigation of the interrelation of age-hardening and creep performance of nickel-silicon-copper alloys, Jenkins and Bucknalll demonstrated that the time required to attain maximum hardness and tensile strength could be expressed by a relationship of the form: t = K • io"^ (i) where t is the time in hours and T the temperature of aging, expressed in degrees absolute, and m and K are constants. They also pointed out that this expression is analogous to that which describes the change of the diffusion coefficient D with temperature; namely, D = Ae-~/m (2) Later, Cohen used this relationship in studies of the mechanism of age-hardening of a silver.rich copper alloyZ and of duralumin.3

Jan 1, 1946

By W. D. Robertson

A considerable quantity of experimental data is available on the effect of time, temperature, work-hardening and composition on the mechanical properties and corrosion resistance of aluminum alloys. There is, however, little unity of purpose or generality in most of the studies and, because the number of variables is large, the results often are not applicable to the problems that arise in practice. Furthermore, the customary expression of the effect of different variables as separate curves or as three-dimensional diagrams with time, temperature and the dependent variables as coordinates, renders the task of selecting the optimum time and temperature of precipitation treatment, with respect to their simultaneous but unequal etfect on the various properties, exceedingly difficult. The introduction of precipitation treatments to raise the yield strength of 24s-type alloys has created a need for a method of correlating and summarizing the effect of time and temperature on the mechanical properties and susceptibility to inter-crystalline corrosion. Correlation is particularly desirable because the choice of time and temperature is of necessity a compromise to achieve the best possible combination of properties, and the optimum conditions cannot he accurately specified unless the data are in a form in which the alternatives can be readily compared. Therefore, the work described here was undertaken to find a common relationship that would be capable of expressing the effect of precipitation time and temperature on the various properties and by means of which the relative effects could be correlated and their interpretation facilitated. Review of Previous Work In connection with an investigation of the interrelation of age-hardening and creep performance of nickel-silicon-copper alloys, Jenkins and Bucknalll demonstrated that the time required to attain maximum hardness and tensile strength could be expressed by a relationship of the form: t = K • io"^ (i) where t is the time in hours and T the temperature of aging, expressed in degrees absolute, and m and K are constants. They also pointed out that this expression is analogous to that which describes the change of the diffusion coefficient D with temperature; namely, D = Ae-~/m (2) Later, Cohen used this relationship in studies of the mechanism of age-hardening of a silver.rich copper alloyZ and of duralumin.3

Jan 1, 1946

By Irwin Roman

IN a previous paper,1 a method was suggested for determining the depth to a bed in the simple case of a uniform overlying layer of constant thickness. The main purpose of the present paper is to show how a slight modification of that method has been used to interpret specific data obtained in the upper peninsula of Michigan by the staff of the Depart- FIG. 1.-THE TECTONIC CONFIGURATION. ment of Mathematics and Physics of the Michigan College of Mining and Technology. The method of Tagg2 has also been used on the same data, thus furnishing a comparison of the e two methods, as well as a method of using the two methods jointly. The method of measuring the apparent resistivity is that suggested by Wenner,3 and illustrated in Fig. 1. A current I enters the earth at the positive pole C and leaves it at the negative pole D. The potential V of the high electrode A, with respect to the low electrode B is measured by suitable means. The separation of the collinear points in the order shown, DBAC, is 1, the same. for each interval.

Jan 1, 1934

By T. V. Moore, H. D. Wilde

In many of the important problems of the petroleum engineer, it is necessary to know accurately the laws governing the flow of gas and liquid mixtures in vertical pipes. Although much work has been done along these lines, no satisfactory solution to the problem has been found. A good theoretical discussion of the energy balance in a gas-lift has been published by Versluys.1 One of the most important factors affecting the efficiency of the flow of oil and gas mixtures is slippage, and in most of the experimental work that has been done no provision has been made for the measurement of this quantity. As Versluys pointed out, since there is no method now known to estimate it from the data usually taken, slippage must be determined empirically. This paper presents the results of some work carried on to measure slippage in short experimental gas-lifts. As shown herein, slippage can be easily calculated in a vertical pipe carrying a mixture of oil and gas if the fractions of the pipe occupied by liquid and gas respectively are known. In this work, the fraction of the pipe occupied by the liquid was measured under a wide variety of conditions and the relationship between this fraction and other quantities, which are easily measured in ordinary work, was determined. It was hoped that the quantitative relationship obtained from this work could be used for making accurate calculations in flowing or gas-lift wells, but unfortunately it did not check satisfactorily when applied to actual wells. Apparently flow in long flow pipes is more efficient than in the short ones used for the experimental work. Nevertheless, it is felt that the data themselves arc of interest; that the method of attack may be of value in future work and that the relationship derived between slip and the relative velocities is a contribution toward the solution of the gas-lift problem.

Jan 1, 1931

By Oswald J. Heinrich

The deposit of rock salt along the shores of Lake Huron, in Canada, has been brought before the public during the last six months, in consequence of the developments made by the diamond drill at Goderich. It is likely to be of more than common interest in the future, since now actual operations have been commenced to exploit the deposit and work it by regular mining. The methods of mining rock salt being but little known in this country, it may be of interest to make a few general remarks in regard to them before entering, upon the description of this new mining enterprise. According to the conditions under which salt is .found in nature, various methods have been resorted to, in course of time, to make it available for the human race. They consist in: A. Natural or solar evaporation. B. Artificial evaporation, either exclusively or in connection with the former. C. Mining the rock salt in its natural state, and converting it to a marketable product, if need be, by simply pulverizing it. Without going into the details of the various methods of making salt available in an economical point of view, dependent on its degree of pority, or on various local influences, we cannot refrain from alluding to the general principles which influence the mining and manufacturing of salt in countries where they have been carried on for hundreds of years. ECONOMICAL CONDITIONS FOR SUCCESS. Salt being one of the articles of prime necessity, and one universally distributed throughout nature, it must always be sold at a comparatively low price. It would even be quoted in the market at prices far below those now ruling, if it were not for the high duties generally imposed upon it, for purposes of state revenues. But looking closer into the subject, it will be found that this duty is probably one of the least oppressive, although in some countries it exceeds sixfold the cost of profitable production. To produce the article at the lowest possible cost requires, therefore, a

Jan 1, 1879

By John W. Padan, Thomas E. Howard

Most of what has been written during the past few years on marine mineral resources has emphasized the vast potential of the ocean, and its floor, as a source of the vital mineral raw materials upon which our modern technological society depends. Computations have been made to demonstrate that the sea contains sufficient minerals to support any reasonable world population indefinitely. The importance of these resources from the standpoint of strengthening the national mineral resource base has been pointed out. And though the information upon which these conclusions are based is sketchy, essentially qualitative, and often conflicting, there can be no doubt that the mineral potential of the sea is tremendous and that there are compelling reasons for working toward its exploitation. Unfortunately, there has been little emphasis on the problems that must be overcome, from the perspective of the economics of mineral production. Some of these problems have been noted, and some authors have appraised them realistically. However, many proposed solutions have been more romantic than practical, from the standpoint of both technology and economics. As a result the general impression has been given, particularly to those uninitiated in the realities of mineral production, that the mineral wealth of the sea is there for the taking-requiring only a good modicum of courage and technologic innovation to place it within easy grasp. But developing the capability necessary for substantial, profitable production of sea bottom minerals will be far from easy. It will be accomplished much more quickly if the problems are faced squarely, defined properly, and attacked in an orderly, logical sequence. While this approach may lack glamour, it offers the highest probability for success.

Jan 6, 1966

By Henry D. Hibbard

Henry D. HibbaRd, Pittsburgh, Pa,: This is a most interesting and instructive paper, some of whose lessons should find immediate application. It points out how fuel-consumption is to be decreased in open-hearth practice, by changes in the plan of the furnace. To look first at the greatest item of loss, radiation, it is seen that thicker brick-work is advisable to lessen this. Especially is this true of the roof, made at present, almost universally, only 9 inches thick to prevent cutting. Now that high roofs, well above the course of the flame, are becoming general, and the average melter is better able to judge the temperature of his furnace, that reason has less force; and we may build roofs 18 inches thick, or perhaps better cover the usual 9 inches with an equivalent layer of sand, which has the advantage of following the arch as it rises and falls with the different degrees of heat. The side-walls of the hearth, usually 131/2 inches thick, may also he thickened up to 18 inches, and the door-linings to 7 inches; and the heat thereby saved will be valuable, while its absence from the working-platform will be much appreciated by the workmen.

Jan 1, 1892

Copper ores from small mines in the area south of Tucson, where the Twin Buttes mine is located, were first operated in the 1880's. Today this area is one of the great copper mining centers of the world. In 1963, Anaconda Company acquired the property from Banner Mining Company and in recent years joined with AMAX in a 50/50 partnership to work the Twin Buttes property. From the beginning, Anaconda had relied on conveyors to remove overburden, oxide material for eventual leaching, and ore from the open pit. In the large st preproduction stripping program in mining history, Anaconda in a four-year period (1965 to 1969) removed 266 million tons of overburden of an average depth of 500 ft (152 m) lying over the ore body. The alluvium overburden was stripped by scrapers carrying 70 to 80 tons and push-loaded by two D9 tractors operating in tandem. The scrapers delivered their loads to bins which fed a 60 in. (1.52 m) conveyor having a capacity of 8500 tph. The 25% slope belt conveyor, which was 2100 ft (640 m) long, transported the material to the brow of the pit, where it was transferred to an 8300 ft (2530 m) surface belt to a 1000 ton loadout bin. At this point, the overburden was trucked to the sites of the tailings ponds, where it was used for dam construction. During 1976, the one billionth ton of overburden was removed from the Twin Buttes mine. The Twin Buttes quartz monzonite porphyry contains only scattered mineralization of which chalcopyrite is the most abundant mineral, associated with chalcocite, covellite, minor bornite, and several oxide minerals. Oxidation has progressed to variable depths of up to several hundred feet below the base of the alluvium. Because of the depth of the sulfide and oxide ores and hard rock waste, two in-pit crushers and conveyor systems were also installed for their transport out of the pit; and in 1976 a third crusher and conveyor system was installed lower in the pit for waste rock only. The two initial crushing and conveying systems were designed to handle any of three functions: crushing waste to be disposed of by a rail-mounted stacker -conveyor, crushing oxide ore for conveyor and then truck transport to stockpiles for future leaching, and primary crushing of sulfide ore for conveyor transport to the two 30 in. by 70 in. (0.76 by 1.78 m) secondary crushers and the two 7 ft (2. 13 m) standards and four 7 ft shortheads in the third and fourth stage crushing plant. A third standard crusher has been in- stalled recently. Mining is done by 15 yd (11.5 cum) shovels which load 100- and 150-ton

Jan 1, 1978