Search Documents

By T. Krumins, L. Zunti, R. Frischmuth

"Titanium and titanium alloys are commonly selected for pressure oxidation autoclave vent piping and pressure control valve components, as well as autoclave internals and other process piping. In the autoclave vent application, titanium ignition risk is controlled by limiting oxygen concentration, and preventing high gas velocity gas impingement on surfaces. Oxygen concentration is dependent on the autoclave pressure and temperature operating conditions and therefore oxygen concentration and the associated titanium ignition risk is dependent on standard operating procedures, process control interlocks and permissive conditions. It is not uncommon for these standard controls to be deficient during atypical operating conditions, or for operations to deviate from the operating procedures, increasing the potential for a titanium ignition incident. Titanium ignition risk caused by elevated oxygen concentration in autoclave vent systems can be reduced with the introduction of an online autoclave overpressure calculation and the configuration of associated interlocks and permissive conditions. INTRODUCTION High temperature pressure oxidation (>190°C) is a well recognized and versatile metallurgical oxidative pre-treatment process commonly used to liberate gold from refractory sulphide ores and concentrates before conventional leaching with cyanide. Titanium and titanium alloys are highly corrosion resistant in pressure oxidation process conditions and are therefore commonly selected as materials of construction for many components including: autoclave internals, agitators, process piping, and components in autoclave vent systems. Operations that anticipate or have experienced aggressive corrosion in the vent system often have little choice in material selection other than the use of titanium (Krag & Henson, 1992). Titanium is not suitable for use with elevated oxygen concentrations and is considered a restricted material because of its high pyrophoricity and combustion propagation properties (Beeson, Smith, Stewart, 2007). Several serious incidents have occurred in which titanium materials have ignited in autoclave applications (Zawierucha, McIllroy, Million, 1995). In autoclave vent applications, titanium ignition risk is reduced by preventing elevated oxygen concentrations, maintaining low gas velocities, and minimizing the potential for gas impingement on surfaces. Oxygen concentration in the autoclave vapour phase and vent system is dependent on the autoclave operating pressure and temperature conditions and therefore titanium ignition prevention controls typically include process interlocks and operating procedures based on the selected nominal design operating conditions. However, it is not uncommon for these controls to be deficient or for operations to deviate from the nominal operating conditions over time, increasing the risk of titanium ignition. The introduction of an online calculation of autoclave overpressure and a maximum target autoclave pressure as well as associated process control interlocks and permissive conditions can alert the autoclave control room operator and prevent an elevated oxygen concentration from developing, and therefore reduce titanium ignition risk in autoclave vent systems."

Jan 1, 2016

By L. M. Pero

The paper summarizes aspects of the recent literature on mineral development in the Third World. The emphasis is on publications covering agreements between host governments and mining companies.

Jan 1, 1985

By Nathan Bowersox, Zuzana Skovajsova, David M. Jurich, Brian Harris

When unwatered after more than 50 years of operation, the White Rock Tunnel of the Upper American River Project in the foothills of the Sierra Mountains exhibited failing rockbolts and ground falls. Repairs designed for the 5 mile-long, 24-foot horseshoe unlined hydropower tunnel included pattern rock bolts, shotcrete, and cleanout of the rock trap. The work, originally scheduled for two 3-month winter outages, was completed under challenging conditions in a single 4-month outage following a carefully sequenced work plan using robotic shotcrete and rockbolter machines. Flexibility, creative solutions, and collaboration by all parties were key to project success.

Jun 13, 2021

By Todd Kilduff, James Grillo, Shrey Arora

In efforts to improve ingress/egress from the existing subway platforms in PATH’s Exchange Place Station, a new 18-foot horseshoe cross-passage tunnel was constructed by Walsh Construction who retained Kilduff Underground Engineering for design of the initial support system and to install and maintain geotechnical instrumentation. The project presented some unique challenges as a result of the proximity to pedestrians on the platform. PATH service remained uninterrupted, limiting the Contractor to mechanical means of excavation to advance the heading. The logistics proved very challenging for the approximate 100-foot-long tunnel excavated in soft Manhattan Schist. This paper will present the design and construction challenges for the project.

Dec 1, 2022

By H. L. Holden

The single line grinding circuit at Bond Gold's Colosseum mine consists of variable speed drive semi-autogenous (SAG) milling and secondary grinding with a fixed speed ball mill. There are several advantages and disadvantages of operating SAG mills with variable speed drives. Discussion in this paper will focus on the effects of variable speed SAG milling in relation to mill liner wear, grinding media consumption, and mill operating availability. Operating experiences, corresponding mill data, and pertinent design changes are also presented.

Jan 1, 1991

By C. A. Rawlins, P. Rostami

"Ventilation systems are not only an integral part of any underground mine design but are a significant contributor to the mine’s capital and operating costs. The ventilation and cooling design systems presented in this paper were part of the prefeasibility evaluation of an underground platinum mine in South Africa. The mine would ultimately operate at the depth of 1,200 m below surface with a proposed 4 Mtpa production rate. The proposed mining operation is a highly mechanized operation using diesel equipment. Significant daily production rate, large amount of equipment and expansive nature of the operation, contributed to a challenging while flexible ventilation design requirements. This paper presents how to safely and efficiently optimize capital expenditure and operating costs associated with the mine air cooling and refrigeration system through practical ventilation design practices. Successful capital and operational savings by modulating installation and commissioning of refrigeration facilities can influence the economic realization of such systems. The adapted planning and design approach provided a cost-effective advantage while complying with design safety and regulations. INTRODUCTION This paper outlines a prefeasibility evaluation of the heat loads and related cooling system to be employed at the proposed platinum mine. The paper also provides appropriate details for a comprehensive understanding of the applied methodology. The proposed mine will be a trackless underground operation using a combination of mining methods. Initially, ore zones with vertical thicknesses greater than or equal to 18 m will be mined using the long-hole stoping (LHS) method, while thinner ore zones will be mined using mechanized drift-and-fill or drift-and-bench methods; hence, a highly mechanized operation with LHDs, trucks, drill rigs, personnel carriers, etc. is envisioned. Broken rock (ore and waste) will be transported by the means of trucks to the main passes (ore and waste) and collection points. Mining zones identified in the project occur at depths ranging between approximately 700 m to 1,600 m below surface. Primary access to the mine will be via a 1,100 m deep, 10 m diameter production shaft (named Shaft No. 2), three additional shafts will be sunk to provide future ventilation and production support. Three main access levels are established as primary haulage levels and include a series of interconnecting ramps. Additional mining sublevels will be developed as necessary. Figure 1 shows the proposed shaft locations and main access levels in a 3-D elevated view. Mining is performed using highly productive mechanized methods. For this reason, an annual ventilation estimate is based on requirements for mobile equipment (i.e., 0.06 m3/s/kW). The air requirements imposed on the underground operation is further influenced by equipment heat loads, auto compression, and virgin rock temperature, as the main sources of in-mine heat."

Jan 1, 2015

By Dongjie Zhang, Shuxin Liu, Jianduo Wang

Broken rock mass and unreasonable stope structure parameters can cause excessive ore loss and dilution in sublevel caving; this is the main problem faced by caving mining in recent years. This paper proposes a stope structure parameter optimization method suitable for steeply inclined medium-thick broken ore bodies and evaluates the reliability and effectiveness through case studies. To solve the problem of large ore loss and dilution in the high-end wall sublevel caving method of Xilinhot fluorite mine, it is necessary to select proper stope structure parameters. Based on the theory of random media, an end-wall ore drawing experiment was carried out, and the bulk flow parameters needed to optimization of stope structure parameters were determined. In the experiment, it was found the draw-out body of high-end wall ore drawing showed a fine top and a thick bottom; the granular media had good fluidity. The reasonable caving step is determined to be 1.2 m instead of the 1.6 m originally used. Through the optimization experiment of the mining route position along the vein, the study found that the best route position is different with the ore body inclination. When the inclination angle of the ore body was 90°, the reasonable route was located in the center of the ore body. When the inclination angle of the ore body was between 85° and 90°, the route moved from the center of the ore body to the footwall at a rate of 22.5%. When the inclination angle of the ore body was between 80° and 85°, the route moved to the footwall at a rate of 54.8%. When the inclination angle of the ore body is not greater than 80°, the route should be arranged on the boundary of the footwall. Field application results showed the dilution rate reduced by 7.66% and the recovery rate increased by 7.31%. Field test results verify the effectiveness and applicability of the optimized stope structure, which corroborates the effectiveness and applicability of the optimized stope structure.

Mar 10, 2022

By Matthew Wilcock, Kenichi Soga, Peter Wright

"This paper discusses how an existing grey cast iron segmental tunnel lining responds to construction of a new SCL tunnel transversely beneath with zero clearance; how the damage assessment for the existing tunnel was conducted for impact of longitudinal movement; how the tunnel is subsequently instrumented to observe both movement and stress manifestation at its longitudinal connections and how the results from the instruments compare with the prediction. An assessment of neutral axis of the tunnel in longitudinal flexure is also explored using interpolated horizontal displacement data from a conventional monitoring system. INTRODUCTION The Royal Mail Tunnel (RMT) (formely Post Office Tunnel or ‘Mailrail’) was constructed using semi-mechanised deep level construction techniques from 1914 and 1917 (Lee 1938). Commencing full commercial operation in 1926, the system was until 2003; conveying parcels the 6.5 miles between seven sorting offices in the center of London, and linking the system with main line rail stations, Paddington and Liverpool Street (The British Postal Museum & Archive 2013). A single tunnel of 2.74m internal diameter facilitated a bi-directional twin narrow-gauge (~611mm gauge) railway road system for electric driverless operation. The tunnel lining is segmental grey cast iron (grade 10) made up of six flanged segments and a smaller flanged key segment; constructed into a ring of width 508mm The external diameter of the tunnel is 2.971m. For further details of the tunnel lining and material properties are outlined by (Devriendt & Alhaddad 2014).London Underground Bond Street Station is a major station of the London Underground system in the very center of London; in its vicinity, the RMT runs west-east perpendicularly above the north south Jubilee Line tunnels. Historic survey record of the Jubilee Line’s (the then Fleet Line) construction in 1974 and its impact on the RMT case is documented in (Crossrail 1993): it is one of only a hand full of case-studies frequently cited when assessing the impact of new construction scenarios of this type; not least including the assessment of the same tunnel, at the same site some 40 years later, and the subject material for this paper: It noted significant vertical displacement of ~90mm to the RMT without noticeable serviceability or operational impediment."

Jan 1, 2016

By Muhammed Şener, Ahmet Gültek

The flotation chemicals are important in mineral processing, and new progress is made in this area day by day. For sanidine purification, some commercial collectors, which can be harmful to the environment, are used. In that respect, the poly(amidoamine) (PAMAM) dendrimers, which are non-toxic for the environment, are good candidates for flotation applications. In this study, the second-generation PAMAM dendrimer was used as a collector to remove magnetite from sanidine by microflotation method, and obtained results were compared with commercial collectors. The results showed that the PAMAM dendrimer is an efficient and selective collector for magnetite. PAMAM adsorption mechanism was determined by zeta potential and FTIR spectra. According to the microflotation results, 87.76% of magnetite recovered at pH 8 by using PAMAM as a collector. It was found that the flotation recovery with the PAMAM dendrimers is similar to the Aero 704 between pH 2 and 6 but less between pH 6 and 9 and more between pH 9 and 12. All experiments were carried out five times and the standard deviation of all results was evaluated with p = 0.05 confidence interval. The second-generation PAMAM dendrimers can be an alternative flotation chemical to the commercial ones concerning usability at a wide pH range, recovery potential, and environmentally benign.

Apr 28, 2023

By Danqing Gao, Brijes Mishra

Spatial variance of rock properties is an important characteristic of rock which addresses the heterogeneity of mechanical and physical properties and their effect on underground mining. Assessing spatial variance can be useful for both locating potential difficult grounds and performing reliability analysis in the mining support system. This study shows a microscale numerical model for rock material based on continuum mechanics. To consider the spatial correlation factor of mechanical properties in realistic rock mass, this study introduces a spatial correlation concept into the traditional type III extreme value distribution model. Based on the improved microscale random model, we conducted a series of numerical uniaxial compressive tests and one longwall mine model to investigate the progressive failure of rock. The results show that spatial correlation factor can significantly affect the load-deformation curves and fracture patterns. The spatial variance model was applied to a longwall mine that included several cutting sequences to observe the influence of the spatial variance on roof behavior. The cohesion and friction random fields induced failure that propagated randomly through the immediate roof in different entries. The results showed that the spatial variance provides an accurate prediction of erratic roof falls in coal mines.

Jul 20, 2020

By Levent Ozdemir, Charles Merguerian

Between 1996 and 1999, a high-performance Robbins TBM [235-282] excavated a 5 mile long, 23´2? wide, and ~700´ deep tunnel through the subsurface of southwestern Queens. Low penetration rates (~6´/hr [actual] vs. ~9´/hr [anticipated])resulted from changed rock mass conditions mostly attributable to high-grade metamorphism of the rocks. Over a three-year period, as-built circumferential geologic mapping (scale 1?=10´) and digital imagery of the tunnel, fracture and fault analysis, structural, lithologic, and petrographic studies have shown that the rocks of the Queens Tunnel consist of orthogneiss of mesocratic, leucocratic, and mafic composition. These metaigneous rocks developed coarse-grained fabrics during Grenvillian (~1.0 Ga) granulite facies metamorphism, and retained their nearly anhydrous, poorly foliated character during subsequent high-grade Ordoviciande formation. Lacking a penetrative foliation, the coarse granoblastic rock texture and extraordinary garnet content (up to 50% in some zones) together proved animpediment to efficient chip production and resulted in bimodal production of blocks and excessive fines. TBM excavation of the Queens Tunnel was also hindered by geological conditions that included unexpected lithology and rock fabric orientation, a zone of crosscutting hypabyssal rhyodacite dikes, and unanticipated extent of brittle faults. The dikes and brittle faults produced blocky ground conditions and a collapsing face condition that produced cutter damage and decreased utilization. Such fundamental textural, mineralogic, and lithologic control over hard-rock TBM penetration can be predicted by careful pre-bid geological analysis. To determine the causes of lower than anticipated TBM performance, a detailed investigation was carried out that included analysis of operational data from the TBM data logger and an extensive laboratory test program on cores retrieved from tunnel walls. Integrated laboratory testing included punch, point load, tensile strength, Cerchar abrasivity, and linear cutting tests, independent petrographic analysis and machine performance analysis. These allied investigations have provided quantification that the rock mass exhibited an unusually high degree of toughness and rock directional properties and established geological causes for decreased TBM penetration rates.

Jan 1, 2003

By D. R. Spears

The U.S. Bureau of Mines has developed a Fast Air-injected hydrocyclone-Shallow Tank (FAST) flotation system. Conventional flotation cell kinetics are a compromise between two conflicting requirements, the need for an agitated zone for rapid bubble-particle collision, and a quiescent zone for bubble-pulp separation. The Bureau of Mines has designed a flotation system in which bubble-particle collision and bubble separation are carried out in two discreet unit operations. A bubble slurry was mixed with an ore slurry at a high rate in a modified air-injected hydrocyclone for rapid bubble-particle collision. The mixture was then fed into a unit specially designed for rapid separation of the bubbles from the pulp. A conventional flotation cell required 2.8 min to obtain 90 pet recovery at a 7-pct Cu rougher concentrate grade, whereas the FAST flotation system can obtain 85 pet recovery with a 13-pct Cu rougher concentrate grade in 0.28 min, and 92 pet recovery with a 7-pet Cu grade in 0.56 min. The Bureau's FAST flotation system is adaptable to a wider variety of flow sheets and could potentially allow for replacement of conventional flotation cells with smaller and faster units.

Jan 1, 1991

By Verya Nasri, Behrouz Esmaeilkhanian, Mohammad Motallebi

The Mount Royal Tunnel (MRT) is a 100-year-old railway tunnel located in Montreal, Canada. The tunnel is approximately 5 km long, 8.7 m wide and 5.5 m high, with a constant 0.6% grade. This existing tunnel will be used by the new Montreal light rail transit network, Réseau Express Métropolitain (REM). This requires the tunnel to be inspected, rehabilitated and made compliant to the recent safety standards. This paper presents the details of the structural inspection and rehabilitation of the tunnel along with the repair methods, addition of a center wall as well as the enlargement of the tunnel section.

Jun 13, 2021

By R. J. Bridwell

Acid mine drainage (AMD) occurs in high sulfur coal and heavy metal mining environments. We show remediation methods using 3D numerical ground water flow models and chemical kinetics of pyrite oxidation for acid leaching of pyrite during air and ground water flow. A recently developed numerical model couples air and water flow with kinetics of iron-reactive bacteria, oxygen transport, specific chemical reaction rates, and pyrite oxidation to calculate migration control of pollution. A model is presented which considers diminution of acid mine drainage in pyrite rich ore bodies by raising the potentiometric surface through a vadose zone to reduce acid mine drainage. A ground water model is presented of an initially saturated mountain, containing an adit, with a sloping ground water table. Ground water recharge consists of snowfall and normal precipitation. Simulations indicate that the historically open adit creates a desaturated mountain above the adit. Significant air saturation ranging from 10-90% oxygen can occur to depths of the adit (-270 m). Remediation consists of plugging the adit, which fill s adit and mountain with water from recharge. Plugging the adit required <10 years for resaturation and rise of the water table in the mountain.

Jan 1, 1994

By W. R. Peters

An experimental hole-to-hole seismic probe system has been developed for use in coal measure geology as a means of determining the structural conditions of coal seams. The source probe produces a 500-joule electric arc discharge whose seismic wavelet has a spectrum in the 200 to 2,000 Hz frequency range. Low compliance hydrophones contained in the source probe as well as in a separate seismic detector probe are matched to the frequency range of the source. Both probes are constructed with 5-72 cm diameter housings. The transducers in the probes are equipped with fluid-inflatable boots to permit operation in either wet or dry boreholes. Preliminary tests in vertical boreholes drilled 213 m apart in sedimentary rock formations show reliable operation and useful seismic propagation measurements along horizontal and oblique paths up to 232 m in length. Because the seismic wave- let has an accurately repeatable waveshape, multiple shots and signal averaging techniques can be used to enhance the signal-to-noise ratio and extend the transmission distances.

Jan 1, 1985

By Martin B. Treuhaft

Expectations for coal in the early to mid-1970&apos;s prompted the government and industry to pursue research and development programs to increase underground and surface mining coal productivity and net coal recovery. Several programs concerned advanced surface mining methods for thin seam coal recovery. Three such programs, along with related areas of interest, are presented in this paper, namely: (1) extended depth augering for trench-strip applications; (2) high recovery auger heads for enhanced recovery; and (3) variable wall mining in low cover longwalls. Conceptual development is examined, prototype testing is discussed, and potential operations are considered.

Jan 1, 1983

By S. Lin, Y. J. Wang

Based on systematic definitions of a generalized multiple fan ventilation system, the concepts of an augmented system, its solution curve and the operating points of the original system are introduced. The Quasi-Newton algorithm is applied in combination with the switching-parameter method to ensure a continuous search along an augmented-system solution curve and identify all the possible system operating points on it. Two example networks are analyzed to demonstrate those concepts and the application of the algorithm for identifying operating points of multiple fan ventilation systems.

Jan 1, 1994

By Roland Trunk, Marcel Imbach, Yves Boissonnas, Jan Vesely

"INTRODUCTION The expansion of the Suez Canal, which runs between the Mediterranean and Red Sea, is at the top of Egypt’s economic agenda. The £8 billion development plan includes a new channel alongside the existing one which will double the number of ships able to pass each day and several tunnels to connect the Sinai peninsula to the main part of Egypt. The Egyptian government ordered three new tunnels under the Suez Canal in the area of Port Said as part of the Canal Region Development Plan. The three tunnels will contribute to the North Sinai expansion, helping to create a vast industrial zone and completing the coastal road extension from Rafah to Nuewiba. Two of these three tunnels will be allocated for roads and the third for railway traffic. A further part of the Suez Canal development mega project are an additional six tunnels in the area of Ismailia and Suez. The focus of this paper is on the two road tunnels in Port Said and will give an overview of the project and the challenges encountered regarding the technical complexity and tight time schedule both in its design and execution. PROJECT OVERVIEW The tunnels will be built in the area of Port Said (see Figure 1) which is the most northern part of the Suez Canal.The road alignment connects the Port Fuad Road in the east bank of the Suez Canal to the Port Said-Ismailia highway in the west bank with a dual carriageway section. Each of the carriageways has two lanes. The bored diameter of the 2.8 km long road tunnels is 13.050 m and will be driven with two Mix-Shield TBMs. The distance between the two tunnel axes is planned with 42.5 m (discussion about a reduction are ongoing). The width of the Suez Canal is around 340 m at upper level and around 170 m at the bottom. During the TBM drive, three main geological layers are expected. Below a depth of around 40 m in a very soft clay layer, a dense to silty sand layer is predicted. Within the sand layer another silty hard clay is expected in different depths with variable thickness. After finishing the excavation of the road tunnels, the same TBM will be used for the railway tunnel. The lowest points of the road tunnels will be located 59 m below the surface (tunnel invert to surface) and only 18 m of ground cover exists between the tunnel crown and the Suez Canal invert. Minimum ground cover over the tunnel crown is approximately nine meters at the tunnel portals."

Jan 1, 2016

By Peter Bush

The deposition of metastable carbonate minerals in ar. aid, sheltered, coastal environment, leads to the formation of a flat, coastel, sabkha plain. The ground waters of the sabkha plain are modified by evaporation, precipitation of salts and reaction between ions in solution and the host carbonates. The resulting brine is similar to those found in fluid inclusions associated with Mississippi Valley type deposits. The aragonite and high magnesium calcite found in the sediments can concentrate lead and zinc from sea water. On diagenesis the lead and zinc are released into the sabkha brines.

Jan 1, 1979

By Richard M. Crowell

"As thorough sampling is usually expensive, the cost of a complete job is often unwarranted, and a cheaper approximation must be substituted. The engineer should, however, weigh the situation thoroughly before subscribing to an alternative other than an accurate assay basis on which to build his conclusion." Examination and Valuation of Mineral Property. R. Parks, 1949

Jan 1, 1994