Search Documents

By J. O. Betterton, D. S. Easton

A detailed investigation was made of the phase diagram of silver-zirconium, particularly in the region 0 to 36 at. pct Ag. The system was found to be characterized by two intermediate phases Zr2Ag and ZrAg and a eutectoid reaction in which the -zirconium solid solution decomposes into a-zirconium and Zr2Ag. It was found that impurities in the range 0.05 pct from the iodide-type zirconium were sufficient to introduce deviations from binary behavior, and that with partial removal of these impurities an increase in the a-phase solid solubility limit from 0.1 to 1.1 at. pct Ag was observed. The phase diagram of the silver-zirconium system is of interest as an example of alloying a transition metal from the left side of the Periodic Table with a Group IB element. Silver would normally act as a univalent metal, its filled 4d-shell remaining undisturbed during the alloying. However, there is a possibility that some of the 4d electrons might transfer to the zirconium. An insight into such a question can occasionally be obtained by comparison of phase diagrams. The silver-zirconium system forms part of a more complete review of various solutes in zirconium in which these valency effects were studied.' Earlier work on the silver-zirconium system was done by Raub and Enge1,2 who investigated the silver-rich alloys. After the start of the present experhents, work on this system was reported by Kemper3 and by Karlsson4 which for the most part agrees with the phase diagram presented here. EXPERIMENTAL PROCEDURE The alloys were prepared by arc casting on a water-cooled, copper hearth with a tungsten electrode and in a pure argon atmosphere. Uniform solute composition was attained by multiple melting on alternate sides of the same ingot. Progressive improvements in the vacuum conditions inside the apparatus during the course of the experiments reduced the Vickers hardness increase of the pure zirconium control ingot from 10 to 20 points, observed initially, to negligible amounts at the end of the experiments. Such hardness changes in zirconium are a well known indication of purity. For example, -01 wt pct additions of oxygen, nitrogen, and carbon increase hardness by 6, 10, and 3 VPN respectively. '9' Further verification that the final casting technique did not add a significant quantity of impurities was obtained when pure zirconium was arc cast and then isothermally annealed in the vicinity of the allotropic transition. The transition was always observed to take place over the same temperature range as in the original crystal bar. The alloy ingots were annealed in sealed silica capsules for times and temperatures which varied between 1 day at 1300°C and 60 days at 700°C. The best method found to prevent the reaction of the zirconium with the silica was foil wrapping of molybdenum or tantalum. With this method, samples of pure zirconium were found to be unchanged in hardness after annealing for 3 days at 1200°C. In most of the experiments the protection of these foils was supplemented by an additional layer of zirconium foil inside the molybdenum or tantalum foil. The alloys, foil, and the capsule were outgassed at pressures in the range 10 to l0-7mm Hg in the temperature range 800" to 1100°C before each anneal in order to remove hydrogen and other impurities, and to provide a suitable container for the high purity, inert atmosphere, which is essential in the annealing of zirconium. The temperature measurements were made with Pt/Pt + 10 pct Rh thermocouples calibrated frequently during the experiments against the melting points of zinc, aluminum, silver, gold, and palladium. For the longer anneals the sum of various temperature errors was generally well within ± 2°C. For short-time anneals and during thermal analysis the overall temperature error is considered to be within ± 0.5°C. The compositions of the alloys from the quenching experiments were determined by chemical analysis at Johnson Matthey and Company, Ltd., under the direction of Mr. F. M. Lever. The actual metallo-graphic samples were individually analyzed in every case, and prior to the analyses two or more sides of each specimen were examined to insure that the specimen was not segregated. The sum of the solute and solvent analyses was in each case within the range 99.9 to 100.1 pct. In the course of the experiments, minor impurities in the range 0 to 500 ppm were found to have significant effects on the zirconium-rich portion of the phase diagram. Similar effects had been encountered previously in other zirconium phase-

Jan 1, 1959

The plans involve about ten technical sessions, a day spent in Cripple Creek and in Pueblo, where there will he optional visits devoted to steel, non-ferrous metals, etc.; half-a-day each to mills in Colorado Springs district and an auto trip to the top of Pike's Peak. Finally, a day at Leadville devoted to visits, including the molybdenum works.

Jan 4, 1918

By W. G. Lidman, H. J. Hamjian

' I HE fabrication of many materials from powders involves a sintering process. A mass of powder will sinter because of the excess free energy over the same mass in the densified state caused by the higher total surface area of the powder. An understanding of the kinetics and mechanism of sintering should assist in improving the properties of such materials. The present investigation conducted at the NACA Lewis laboratory deals with the sintering of chromium carbide. Dry sintering (sintering at a temperature below the melting point) was divided into two stages by Shaler:' the first stage, during which the particles preserve much of their original shape and the voids are interconnected, and the second stage, during which densification occurs and the pores are isolated. The mechanism of forming interfaces between particles, or welding together of particles, has been investigated by Kuczynski2 and may be described by any one or a combination of the following mechanisms: viscous flow, evaporation and condensation, volume diffusion, or surface diffusion. The mechanism by which pores are closed or eliminated (densification) during sintering, is of interest. Grain growth observed during sintering may be attributed to the variation in the surface energies of individual grains, causing some grains to grow at the expense of others. Grain boundary migration occurs presumably by a diffusion process, therefore the rate of grain growth would be expected to increase exponentially with increasing time and temperature. Thus, for practical sintering times of less than 1 hr, a certain minimum temperature may exist at which major structural and property changes will occur. Densification and kinetics of grain growth during sintering under pressure of chromium carbide were investigated to provide additional information which will aid in describing more accurately the sintering process and the mechanisms involved. This material was selected for this study because of the current interest in high strength, oxidation resistant refractory materials, such as carbides, which are sintered to produce solid, dense materials from powders. Sintering under pressure is a process where the heat and pressure are applied to the compact simultaneously, specimens for this work were prepared by sintering under pressure at different temperatures and for various time periods. Experimental Procedure Preparation of Specimens: Chemical analysis of the commercial chromium carbide used in this investigation was as follows: Cr 86.19 pct, C 12.14 pct, and Fe 0.2 pct. X-ray diffraction powder patterns gave characteristic diffraction lines of Cr3C2 crystal structure. Powder particle size was determined microscopically and the average initial particle size was 6 microns with 85 pct between 2 and 10 microns. Specimens sintered under pressure were formed in graphite dies3 heated by induction. Sintering temperatures were measured with an optical pyrometer by sighting into a 3/8-in. hole drilled 1 in. deep at the midsection of the graphite die. A load of approximately 1 ton per sq in. was applied to the powder. The die assembly was heated in 20 min to the highest temperature (2500°F') at which no increase in grain size could be observed, and less than 2.5 min were required to heat from this temperature to the maximum temperature (3000°F). Sintering temperatures and times for the specimens of this investigation are indicated in Table I. Analysis of Specimens: Specimens polished with diamond abrasives were etched to reveal the grain boundaries with a 1:1 mixture of 20 pct potassium hydroxide and 20 pct potassium ferricyanide heated to 160°F. Representative areas of each sample were photographed at 1000 diameters. The largest diameters of all well-defined grains were measured, but only the measurements of 15 of the largest grains were averaged in order to determine an index of grain size on the assumption that they were among the first to begin growth. Densities were determined from differential weighing of the samples in air and water. The reported density values are considered correct within ±0.01 g per milliliter. Results and Discussion Metal compacts have exhibited grain growth when sintered at temperatures about two-thirds of the absolute temperature of their melting point.' Grain growth also occurs during the sintering of chromium carbide and is illustrated by the micrographs shown in Fig. 1. These micrographs were prepared from specimens sintered for 90 min at temperatures ranging from 1371°C (2500°F) to 1648°C (3000°F). Average grain size and density measurements of specimens investigated are presented in Table I. The relationship between grain size and sintering tem-

Jan 1, 1954

By K. L. Young

The general energy equation, including change in kinetic energy, was solved by numerical integration and used to evaluate simplifying assumptions and application practices over a wide range of conditions. When extreme conditions were encountered, sizable errors were caused by large integration intervals, application of Simpson's rule and neglecting change in kinetic energy. A maximum error of only 1.31 percent was caused by assuming temperature and compressibility constants at their average value. It was discovered that a discontinuity can develop in the integral for the injection case. This discontinuity indicates a point of zero pressure change and is an inflection point in the pressure traverse. INTRODUCTION When a pressure in a gas well is to be calculated, one of the first decisions is to select a method of calculation. In many instances, this selection becomes a problem because the literature, at best, provides an evaluation of any method for only a limited range of conditions. Once a method has been selected, a question often arises as to the size of the calculation interval which should be used. The question regarding calculation interval arises because an analytic solution is not obtainable and approximate solutions must be used. This paper presents an evaluation of major assumptions and application practices of probably the two most widely used methods for calculating steady-state single-phase gas well pressures. The two methods are Cullender and Smith1-" (numerical integration), and average temperature and com-pressibility. The Cullender-Smith method assumes that change in kinetic energy is negligible and is normally applied in two steps with a Simpson's rule correcton. The average temperature and compressibility method, in addition to neglecting kinetic energy change, asumes that temperature and compressibility are constant at their average values. This method is normally applied for wellhead shut-in pressures of less than 2,000 psi, and in one step. Computer programs were written to compute bottom-hole pressure with and without the assumptions, using various approaches. Values of input parameters investigated are shown in Table 1. Flow rate was limited to a maximum of 5,000 and 10,000 Mcf/D for tubing sizes of 1.610 and 1.995 in. ID, respectively. Flow rate was also limited to 10,000 Mcf/D for a tubing size of 2.441 in. ID when wellhead flowing pressure was 100 psia. These limitations were imposed on flow rate so as not to exceed sonic velocity. The z factor routine available necessitated limiting bottom-hole temperature to 240F and wellhead pressure to 3,000 psia. Pressures were compared on the basis of percent deviation from the trapezoidal integration of Eq. l or 2 at 100-ft intervals. A preliminary investigation indicated that a 1,000-ft interval solution would differ from a 50-ft interval solution by less than 0.25 percent; therefore, the 100-ft interval was chosen for a base. For the purpose of comparison, deviations less than 1 percent were considered insignificant. where 111.1 qeC2/d p = kinetic energy term. Eqs. 1 and 2 can be evaluated numerically at specific depths using the trapezoidal rule as shown by Cullender and Smith. If change in kinetic energy is neglected and temperature and compressibility are assumed constant at their average values, Eq. 1 can be integrated to give the average temperature and compressibility equation,

By W. F. Boericke

NOT the least interesting sights that New York has to offer the visiting mining engineers are the extensive tunnel operations that are being pushed in connection with the subway construction. While a "hard rock" man might feel at home on these jobs, the engineers driving the subway tunnels have necessarily had to encounter some new problems pe-culiar to the largest permanent mining camp in the country. To drive a heading 36 by 18 ft. in hard rock, with a station section to follow 52 by 27 ft. across-and to do it in the midst of a city's traffic-demands engineering skill of a high order. Not the least of the problems overcome by the engineers in charge was to provide adequate ventilation for the men at the face at all times, so that there would be no delay in the work. With a crew of 40 men (32 drill runners and helpers on the machines alone, working two shifts) a hold-up due to inability to get back promptly to the face after shooting would affect costs quickly. AIR VITIATED BY EXHAUST FUMES FROM MOTOR TRUCKS A complication not encountered by metal miners, but which the subway engineers had to meet, was pollution of the air in the tunnels by fumes from the exhaust of the motor trucks used to haul away the broken rock. As shown in the cut, motor trucks were constantly em-ployed to remove the heavy tonnage broken as the tun-nels went ahead, amounting, according to R. J. Van Wagner, chief engineer of the Del Balso Construction Co., to 48 cu. yd. per ft. of tunnel advance. As the length of the tunnel under his management was 900 ft., it was essential for the safety of the men that suffi-cient air be introduced to dilute the poisonous fumes so that no ill effects would be felt for the entire distance that the trucks had to travel. The presence of the ex-haust fumes was especially noticeable on foggy days.

Jan 2, 1928

By J. B. DILWORTA

Ix estimating the investment-value of a mining-property or plant, the value of which decreases with operation, it is often necessary to know the sum which must be set aside periodically from earnings either to renew the plant at the end off its life, or to return the capital involved when the earning-power of the investment has ceased. In such cases it is manifestly incorrect simply to divide the total amount to be retired by the number of periods (usually years) during which the investment shall be active, as the sums periodically withdrawn have a certain interest-earning power varying with the length of time they are held and with the opportunities afforded for their investment. But though the interest may be considered to accumulate regularly year by year, yet the rules and tables for compound interest do not apply, owing to the addition of a fixed amount of new money to the total at the beginning of each period. Briefly stated, the problem of sinking-funds is, to find the amount of money which must be periodically set aside at a certain rate of interest, regularly compounded, to yield a certain sum in a given, length of time. In most practical cases the interest is compounded and the fresh amount added at the same time-usually once a year-and on this basis the problem may be solved as follows

Nov 1, 1909

By Louis W. Huber

The Liberty tunnels extend through a very steep hill in Pittsburgh (locally called Mount Washington) for a distance of slightly over a mile. The two tunnels parallel each other and are 59 ft. apart, center to center (Fig. 1) They are for vehicular traffic, and in each there is ample space for two lines of vehicles. Northbound traffic, toward downtown Pitts- burgh, is confined to the east tunnel and southbound traffic to the west tunnel. The South Hills residential district is separated from downtown Pittsburgh by Mount Washington, a steeply rising escarpment south of and adjacent to the Monongahela River. The Mount Washington district immediately south of the Monongahela River has been reached, for many

Jan 1, 1927

By B. D. Cullity, A. Freda

It is well known that deformation by cold drawing or swaging produces a kind of preferred orientation called fiber texture in metal wires. Such textures have been extensively studied by means of X-ray diffraction, chiefly by techniques in which the diffracted X-rays are recorded photographically. This paper describes some results obtained with a new method, involving the use of a diffractometer. X-RAY METHOD Since the pole figure of a material having a fiber texture is symmetrical about the fiber axis, there is no need to present the entire pole figure. Instead, texture data can be summarized by means of a curve showing the variation of pole density along any meridian of the pole figure, if the north-south axis of the latter is made parallel to the fiber axis. The position of a pole on the meridian is specified by the angle 9 between the pole and the fiber axis (wire axis). The X-ray method1 used here to measure pole density as a function of 9 actually consists of two methods, referred to as A and B. In method a, X-rays are reflected from the wire surface. Pole densities can be measured by this method from O = 90 deg down to a limiting value which is dependent on the Bragg angle 8 and is typically of the order of 30 to 40 deg. Method B involves diffraction from the wire cross section and covers a range of 0 values from 0 up to an angle sufficient to overlap the measurements made by method A. By a combination of the two methods, a complete pole-density curve can be obtained. However, method A alone, which requires no specimen preparation other than etching, can often reveal enough of the pole-density curve to provide complete information about texture components. Both methods require that the measured diffracted intensities be corrected for changes in absorption and diffracting volume with changes in 9. A11 intensities I reported in this paper are corrected diffracted intensities; they are propor-

Jan 1, 1960

Report of the Secretary TO THE BOARD OF DIRECTORS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS Gentlemen:-To a Board of Directors keeping in as close touch with all of the affairs under their care as do the Board of Directors of the A. I. M. E., through their monthly meetings, a report of the year's progress is almost superfluous. To the members who read the monthly reports of. the Board Meetings and of the various activities of the Institute as published each month, a yearly report cannot carry much fresh information; yet for both it may be well, as is the custom, to glance over the field of our activities during the past year, and to make an estimate for the year to come. The beginning of 1924 was not propitious for the members of the mining profession, though tonnage production for 1923 had been high and the gross value higher than for several years. The margin of profit had been narrow, prospecting and development were limited, and many of our members were unemployed, or were working in other industries. Toward the end of the year, higher metal, prices were in sight. Old-time optimism began to grow, and it now brightens the outlook for 1925. An excellent barometer of the prosperity of the industry, and that of the Institute, for they go hand in hand, is the work of our Employment Bureau. During the past few months, the percentage of our members for whom openings have been found has been increasing to a marked extent, and many members who had fallen in arrears are placing themselves in good standing. The number of new members joining has remained about as it was in 1922 and 1923. The Directors have reason to congratulate themselves on the interest maintained during a dull period, for it is not humanly possible to take a keen interest in the technology of an industry when our hands and minds are not actively engaged in it Now, with a much brighter outlook, we can look forward to a year of increasing prosperity for the industry and for the Institute.

Jan 3, 1925

By Y. C. Liu, R. H. Richman

The effects of gel,manium and tin on the deformation and 9-e-crystallization textures of copper have been explored in detail with in the copper-rich terminal solid solutions. Addition of solute to copper produces a change in deformation texture from the copper type to the 70 :30 brass type. This transition has been measured quantitatively The types mid proportions of recrystal-lization components have been determined as a function of com-position, and correlation of recrystallization components with specific deformation components is discussed. On the basis of information available in the literature, it has been suggested that the effect of solute elements on the recrystallization texture of copper

Jan 1, 1961

By T. Egleston

The manufacture of charcoal in kilns was declared many years ago, after a series of experiments made in poorly constructed furnaces, to be unprofitable, and the subject is dismissed by most writers with the remark that in order to use the method economically the products of distillation, both liquid and gaseous, must be collected. It is asserted with truth that the number of kilns required for a large production of iron would be so great that it is doubtful whether any works would be justified in making the necessary outlay for their constructiou, but it can also be asserted with equal truth that for any such production in a given locality the use of charcoal as fuel would be eqnally unjustifiable. It appears to have been forgotten that there were other manufactures besides iron in which large amounts of charcoal were used, but these consumers seen] to have been guided entirely by the results of the experiments of the iron men, who necessarily made the largest qnantity of it. Some authors speak in a doubtful way of the quality of the charcoal produced, and a few concede that with great care good charcoal can he made in kilns, but that most of the workmen do not like kiln 'charcoal. This is the real secret of the opposition to this method of manufacture. Most of these objections were written when charcoal was the most important fuel used by the iron manufacturer, and when what was a largeproduction of iron for several furnaces was less than that produced by a single modern one, in localities where other fuels can be had. Almost all that has been written on the subject related to the use of the fuel for the manufacture of iron in the blast furnace, where very peculiar properties are required, and where the qnantity produced is limited by the height of the furnace, and this in turn by the crushing resistance of the charcoal. A large production was, therefore, only possible when the best and hardest woods were used. Of all these objections there is not a single one which is not eqnally applicable to any method of charcoal manufacture, whether it be meilers, pits, or furnaces. Until recently, therefore, the manufacturers of charcoal iron

Jan 1, 1880

By E. W. Dewing

The nature of solid solutions of sodium in non-paphitic carbon at temperatures near 1000°C has been investigated by an electrolytic technique. The activity coefficient is found to vary strongly with the heat-treatment temperature of the carbon, and an analysis of the energy terms involved suggests that this is due to variations in the Fermi level. The diffusion coefficient for sodium is in the range implying that the sodium atoms (or ions) are not bound to specific sites on the carbon, in agreement with lack of evidence for specific compounds in the activity -composition curves. In the light of These results phenomena occurring in aluminum reduction cell linings are dis-cussed. It is concluded that sodium migrates by diffusion through the carbon lallice and not the pores, and that A14C9 is formed within the lining hy The excess of NaF invariably found in used linings is formed by this reaction and by air oxidation: There has recently been much interest in the swelling of carbon which occurs when it is made cathodic in an aluminum electrolysis cell, and there is general agreement that the phenomenon is due to the penetration of sodium atoms, derived from the reaction on the carbon lattice. (NaF and AlF3 are constituents of the fused-salt electrolyte.) The low-temperature lamellar compounds of potassium with graphite are well-known, and one compound between sodium and graphite has been reported.4 There is, however, virtually no information on the basic chemistry of the interaction of sodium with nongraphitic carbon at high temperatures, although Dell3 has made some fundamental studies of rates of penetration. At the time the present work was carried out these were not available. Rapoport and samoilenkol had measured rates of physical expansion in a dilatometer, using the fractional increase in length of a carbon specimen after electrolysis in a cryolite bath for 2 hr as an index of susceptibility to cathodic swelling. Work here with a similar apparatus showed that expansion (of a 1.5-in.-diam cylindrical specimen) ceased in less than 20 hr, and that the final expansion was much more reproducible than the value at some intermediate time. This suggested that an equilibrium was being set up, and that a thermodynamic approach was required. The results obtained are not as accurate as had been hoped, but they are the only ones of their type available and have enabled useful conclusions to be drawn. The experimental work was divided into two parts: an investigation of the activity-concentration diagram for sodium in carbon, and a rough determination of the diffusion rate. For the former, most of the experiments were made with petroleum coke even though this is not a form of carbon used in cell linings. It has the advantages, however, that it is a homogeneous material, that it is low in ash, and that its structure is reasonably well understood. Anthracites and coal cokes gave results of the same type as obtained with petroleum coke, but the reprodu-cibility from specimen to specimen was extremely poor. EXPERIMENTAL 1) The Activity-Composition Diagram for Sodium in Carbon. The petroleum coke was ground, pressed at 40,000 psi into plates 19 by 9 by 2 mm without added binder, and heat-treated. The sodium activities were established by an electrolytic technique. The carbon was made anodic in a cryolite bath with an aluminum cathode, and a controlled potential, E, applied so that the sodium activity at the anode was given by ln Na = 1n asa - EF/RT [21 where as, is the sodium activity generated by Reaction [I]. The relative activity is sufficient for many purposes and is simply given by The value of Na not at present known, but when the thermodynamics of the Na-A1 system have been worked out it can be derived from the equilibrium

Jan 1, 1963

By R. E. Phelan

WHILE 1931 was a most important year in the history of Canadian copper smelting and refining, nevertheless, due to the low price of copper and the in- ability of the International Nickel Co. to market its full capacity of nickel. the production of both copper and nickel was considerably less than the total installed capacity for the production of these metals. IIY the nor- mal course of events, 1931 should have seen a great increase in the production. of both copper and nickel in Canada, because the large extensions to both the copper smelting plants and the copper and nickel refinery capacity, which had largely been completed in the year 1930, should be showing their effect.

Jan 1, 1932

By R. I. Jaffee, R. W. Wood, H. R. Ogden, D. N. Williams

D. W. Morgan, D. H. Polonis,and R Taggart (Uuivevsity of Washington)—Dispersion hardening in titanium-copper alloys is of particular interest to us in view of our current research activities in phase transformations in this system. We should like to raise questions concerning several points in the paper. The flow sheet for fabrication and heat treatment (Authors' Fig. 2) indicates that 0.045 in sheet is treated in air for a period of 30 min at 1625' F. Were any surface coatings used to reduce oxygen contamination at this stage? One might ask the same question about the 8-hr annealing at 1400F. Contamination during fabrication and heat treatment of such thin sections could be considerable without some protection. Although the authors state that no analyses were made, they note that contamination masks the distinction between base strengths of the different alloys. In this connection, what fabrication and heat-treatment procedures were used in obtaining the comparison specimens of unalloyed titanium? It would seem that oxygen contamination must cast doubt on the reliability of the proposed strength-mean free path relationship deduced from the data (Authors' Fig. 5). It is usual to evaluate dispersion hardening on the basis of yield strength rather than ultimate tensile strength, and accordingly we have replotted the authors' Fig. 1 to include yield strength. The yield strength data do not justify a discontinuity of 3 p at either 70" or 1000 OF. Can the authors substantiate their conclusion 1) with additional evidence? Otherwise it seems that they have succeeded only in pointing out the possibility of a linear relationship between yield strength (or Uts) and the logarithm of the nleall free path, comparable with that demonstrated for iron-carbon alloys (Authors' Ref. 2). Work in our own laboratories has shown that the hardness of the phase Ti,Cu is 235 Vpn, and that of a 1.5 pct (at.) (2 pct wt) supersaturated solid solution of copper in titanium is 190 Vpn. This small difference in hardness would suggest that Ti2Cu should not be a very effective dispersion-hardening phase. D. N. Williams, R. W. Wood, H. R Ogden, RI. L Jaffee (authors' reply)— This discussion brings out some interesting points with respect to the interpretation of our results, and also raises some questions regarding the experimental technique. We shall consider the latter questions first. Contamination during heat treatment was prevented by performing all heat treatments in argon-filled Vycor capsules. Fabrication was done in air, with the usually observed scaling. Scale was removed

Jan 1, 1962

By Sir Albert E. Kitson

The manganese ore deposits of the Gold Coast, British West Africa, occur in very ancient rocks, of both sedimentary and metamorphic types. In certain respects they have a strong resemblance to those of India and Brazil, as contrasted with those of Tertiary age in Georgia, but in this paper no careful comparison with them can be made. Viewed from the present condition of the manganiferous rocks, the oldest deposits are in the sediments. Later than these are the progressively metamorphosed representatives of these sediments. Youngest are the products of decay and degradation with the concentration of manganese oxide in the rocks of both groups. The oldest occurrences are in argillaceous and siliceous phyllites and slates, which show only a moderate degree of metamorphism. They belong to a series which also includes mudstones, sandstones, grits, conglomerates and subordinate limestones, with tuffs and lava-flows, largely of basic types. This has been named the Birrim System. Its age is unknown, for no definite fossils have been discovered in it. Since these non-fossiliferous strata at many plaees are of a character which in many parts of the world are suitable for the preservation of fossils, and which contain them, it is assumed that the Gold Coast deposits are pre-Cambrian. These rocks of the Birrim System have normally a northeast-southwest strike, and are folded, but not to any very great degree except in certain belts. From the Eastern Province of the Gold Coast they may be traversed diagonally across their strike for upwards of 600 miles, to the extreme northwestern corner of the Northern Territories. Thence they probably extend much farther into French territory.

Jan 1, 1927

By Robert A. Haney, Stephen J. Gigliotti, James L. Banfield

A series of investigations were made by the Mine Safety and Health Administration to evaluate the performance of various face ventilation systems as part of a program to reduce frictional ignitions of methane and to develop face ventilation systems that could be used with the line brattice more than 10 feet from the face. Tests were conducted in a full-scale laboratory model of a face area. Systems tested included unassisted blowing and exhaust line brattice, diffuser fan and spray fan systems. Systems were evaluated at air quantities ranging from 1.4 to 7.0 m3/s (3,000 to 15,000 cfm), and brattice-to-face distances from 1.5 to 9 meters (5 to 30 feet.). Tests were designed so that systems could be evaluated for the location of the high-point methane concentration in the face area, methane dilution capacity, and face ventilation index. The methane dilution capacity is the total amount of methane a system can dilute to 1.0 volume-percent. The face ventilation index is the efficiency at which the available face air volume is being used.

Jan 1, 1982

Major William R. Grunow, in a brief account off his military services, says: "I take pleasure in informing you that since my return from France I have been stationed at Camp A. A. Humphreys, Va., and am now on duty as a Senior Instructor at the Engineer Officers' Training School. While in France, I served as a company commander in the 305th Engineers and was later ordered to return to the United States for assignment to new troops. Upon arrival in the United States, I received my majority." P. F. Rodegerdts gives us the following account of his military service: "I enlisted in the Naval Reserve Flying Corps in San Francisco on Feb. 12, 1918. On February 10, I was ordered to Cambridge, Mass., where I was enrolled for the course in technical aircraft construction given at Massachusetts Institute of Technology. After successfully completing the course of instruction, I spent six weeks in practical construction of seaplanes at the Curtiss aeroplane factory in Buffalo. Following this, I was assigned to active service at Akron, Ohio, on June 22, 1918. At the same time I received my commission of ensign U.S.N. R.F. Unfortunately, I have been kept at Akron and although I have made

Jan 1, 1919

By Larry Kaufman, Martin Schatz

The effect of pressure on the extension of the ? loop in the FeSi system has been determined by means of metallogvaphic studies and hardness measurements performed on a series of high-purity Fe-Si alloys containing 7.5, 11.0, and 13.9 at. pct Si, respectively. These mensurements, performed at 42 kbar and temperatures up to 1200oC, indicate that the ? loop is expanded to about 10 at. pct Si at 42 kbar as opposed to a maximum extension of 4 at. pct Si at 1 atm. Comparison of the experimental results with thermodynamic predictions of the pressure shifts yields satisfnctory results. DURING the past few years, several studies have been performed in our laboratory1-' in order to determine the effect of high pressure on phase equilibrium in pure iron and iron-base alloys. The purpose of these studies has been to elucidate the effects of high pressure experimentally and to compare the observed results with predicted pressure effects derived on the basis of known thermody-namic and volumetric data at 1 atm. These studies have included work on pure iron2,5,7 as well as Fe-Ni,1,5 Fe-cr,l,5 and Fe-c4-6 alloys. In addition, Tanner and Kulin3 have reported results of pressure studies on two Fe-Si alloys containing 2.0 and 6.25 at. pct Si. At the time of this latter study, no detailed information was available concerning the difference in volume between the a (bcc) and ? (fcc) phases in the Fe-Si system as a function of silicon content. In order to compare their observations with calculated pressure shifts, Tanner and Kulin were forced to assume that silicon had no effect on the difference in volume between a and ? iron. The resulting discrepancy between their calculation of the a/? phase boundary at 42 kbar and the observed results led them to the conclusion that silicon additions probably decrease the difference in volume between a and ? iron. Recently: Cockett and Davis8,9 have reported de- tailed studies of the lattice parameters of a series of Fe-Si alloys at temperatures ranging from 20" to 1150°C. These measurements, performed on alloys in the bcc and fcc range, show that silicon does indeed decrease the difference in volume between a and ? iron. By correcting the calculations of Tanner and Kulin in line with the observed effect of silicon they were able to show improved agreement between computed and observed pressure shifts.' The present measurements were undertaken to provide additional corroboration of this effect, by extending the range of composition, in addition to exploring a situation where large extensions of a ? loop could result in impingement of the ? field with an ordered bcc phase (based on Feo.75Sio.25). I) EXPERIMENTAL PROCEDURES AND RESULTS The alloys investigated were obtained from Dr. F. Kayser of M.I.T. They were prepared at the Ford Scientific Laboratory by vacuum melting electrolytic iron and high-purity silicon. The melts were poured under an argon atmosphere into hot-topped steel molds. Subsequently the ingots were hot-worked down to 1/2-in.-diam rods. Three alloys containing 7.5, 11.0, and 13.9 pct Si were studied. Carbon, regarded as the principal impurity, analyzed at, or below, 0.001 wt pct for all of the alloys. Prior to pressure-temperature treatment, the rod was annealed for 24 hr in vacuum at 1000°C, water-quenched, and subsequently machined into 0.100-in.-diam by 0.100-in.-long specimens. Subsequent to machining, the specimens were again annealed and then examined metallographically. They were found to exhibit a clear coarse-grained ferrite similar to Figs. 10 and 110 of Ref. 1 and Fig. 2 of Ref. 3. Subsequently, specimens of each alloy were equilibrated at 42 kbar at various temperatures in supported piston apparatus.1,3,4,6 Three specimens, one of each alloy, were wrapped in platinum and exposed simultaneously. The pressure-temperature cycle consisted of increasing the pressure from ambient to 42 kbar at 25oC, heating rapidly to the desired temperature, holding for 15 min, and quenching to 100°C, followed by slower cooling to 25°C and pressure release. The temperature was measured with a Pt/Pt-13 pct Rh thermocouple which was not corrected for pressure effects. Subsequently, specimens were examined metallographically and by

Jan 1, 1964

By J. D. Clark

ONE'S lifetime does not usually offer the oppor-tunity to observe and be a part of the commercial development of an entirely new material. Petalite has been known for over a century, but at first it was presumed rare. However, it was found to be so abundant that it has become a new and extremely useful industrial tool. Mineralogy Petalite is a lithium-aluminum-silicate mineral. It was from petalite that J. A. Arfwedson first discovered lithium in 1818. The theoretical composition of Li2O • A12O8 • 8SiO2 is equivalent to 78.4 pct silica, 16.7 pct alumina and 4.9 pct lithia. The mineral in its known commercial occurrence is colorless to white and rarely gray, transluscent and rarely transparent. It is brittle, has a vitreous luster, and occurs usually in cleavable masses (fig. 1). It is classified as a di-silicate, but is similar in composition to the metasilicate spodumene, Li2O.-Al2O8-4SiO2 (table I). However, their specific gravities are quite different (3.13 to 3.20 for spodumene, 2.39 to 2.46 for petalite). Occurrence Petalite specimens have been reported in many localities; however, there are only three known countries having occurrences of commercial significance. The classic locality is Sweden's Utö Mines, which, although reportedly still containing considerable petalite, have been closed and are not expected to be operated in the near future. At Varuträsk, in northern Sweden, petalite carrying 4 pct lithium oxide is the main ore. In 1946 there was reported about 1000 tons on hand. However, the iron content was 0.60 pet too high for other than chemical use. Petalite has been reported in western Australia. At the Cottesloe mine, where small quantities have been reported available, it is produced in conjunction with feldspar. Petalite occurs in considerable quantity in the feldspar quarry at Londonderry, and it was estimated1 in 1943 that over 3700 tons might be available. The petalite in South West Africa was first discovered by F. J. Jooste, a lawyer by profession, in 1938. The following year he discovered a much larger deposit, and in 1948 another important discovery was made. These deposits occur near Kari-bib and constitute the only known commercial deposits. Their full extent has not yet been determined, but huge massive blocks of petalite of the purest grade, running into many thousands of tons, can be seen in all these deposits. To date, 60,000 tons of high grade, low iron containing ore has been blocked out in the major bodies. Mining for years to come will be confined to simple quarrying. Selection from accessory minerals has proved

Jan 1, 1951

By J. D. Clark

ONE'S lifetime does not usually offer the oppor-tunity to observe and be a part of the commercial development of an entirely new material. Petalite has been known for over a century, but at first it was presumed rare. However, it was found to be so abundant that it has become a new and extremely useful industrial tool. Mineralogy Petalite is a lithium-aluminum-silicate mineral. It was from petalite that J. A. Arfwedson first discovered lithium in 1818. The theoretical composition of Li2O • A12O8 • 8SiO2 is equivalent to 78.4 pct silica, 16.7 pct alumina and 4.9 pct lithia. The mineral in its known commercial occurrence is colorless to white and rarely gray, transluscent and rarely transparent. It is brittle, has a vitreous luster, and occurs usually in cleavable masses (fig. 1). It is classified as a di-silicate, but is similar in composition to the metasilicate spodumene, Li2O.-Al2O8-4SiO2 (table I). However, their specific gravities are quite different (3.13 to 3.20 for spodumene, 2.39 to 2.46 for petalite). Occurrence Petalite specimens have been reported in many localities; however, there are only three known countries having occurrences of commercial significance. The classic locality is Sweden's Utö Mines, which, although reportedly still containing considerable petalite, have been closed and are not expected to be operated in the near future. At Varuträsk, in northern Sweden, petalite carrying 4 pct lithium oxide is the main ore. In 1946 there was reported about 1000 tons on hand. However, the iron content was 0.60 pet too high for other than chemical use. Petalite has been reported in western Australia. At the Cottesloe mine, where small quantities have been reported available, it is produced in conjunction with feldspar. Petalite occurs in considerable quantity in the feldspar quarry at Londonderry, and it was estimated1 in 1943 that over 3700 tons might be available. The petalite in South West Africa was first discovered by F. J. Jooste, a lawyer by profession, in 1938. The following year he discovered a much larger deposit, and in 1948 another important discovery was made. These deposits occur near Kari-bib and constitute the only known commercial deposits. Their full extent has not yet been determined, but huge massive blocks of petalite of the purest grade, running into many thousands of tons, can be seen in all these deposits. To date, 60,000 tons of high grade, low iron containing ore has been blocked out in the major bodies. Mining for years to come will be confined to simple quarrying. Selection from accessory minerals has proved

Jan 1, 1951