Search Documents

By W. M. McKewan

Magnetite pellets were reduced in flowing hydrogen at pressures up to 40 atm over a temperature range of 350° to 500°C. The rate of weight loss of oxygen per unit area of the reaction surface was found to be constant with time at each temperature and pressure. The reaction rate was found to be directly proportional to hydrogen pressure up to 1 atm and to approach a maximum rate at high pressures. The results can be explained by considering the reaction surface to be sparsely occupied by adsorbed hydrogen at low pressures and saturated at high pressures. PREVIOUS investigation1,2 have shown that the reduction of iron oxides in hydrogen is controlled at the reaction interface. Under fixed conditions of temperature, hydrogen pressure, and gas composition, the reduction rate is constant with time, per unit surface area of residual oxide, and is directly proportional to the hydrogen pressure up to one atmosphere. The reduction rate of a sphere of iron oxide can be described3 by the following equation which takes into account the changing reaction surface area: where ro and do are the initial radius and density of the sphere; t is time; R is the fractional reduction; and R, is the reduction rate constant with units mass per area per time. The quantityis actually the fractional thickness of the reduced layer in terms of fractional reduction R. It was found in a previous investigation2 of the reduction of magnetite pellets in H2-H,O-N, mixtures, that the reaction rate was directly proportional to the hydrogen partial pressure up to 1 atm at a constant ratio of water vapor to hydrogen. Water vapor poisoned the oxide surface by an oxidizing reaction and markedly slowed the reduction. The enthalpy of activation was found to be + 13,600 cal per mole. It was also found that the magnetite reduced to meta-stable wüstite before proceeding to iron metal. The following equation was derived from absolute reaction-rate theory4,8 to expfain the experimental data: where Ro is the reduction rate in mg cm-2 min-'; KO contains the conversion units; Ph2 and PH2O are the hydrogen and water vapor partial pressures in atmospheres; Ke is the equilibrium constant for the Fe,O,/FeO equilibrium; Kp is the equilibrium constant for the poisoning reaction of water vapor; L is the total number of active sites; k and h are Boltzmann's and Planck's constants; and AF is the free energy of activation. Tenenbaum zind Joseph5 studied the reduction of iron ore by hydrogen at pressures over 1 atm. They showed that increasing the hydrogen pressure materially increased the rate of reduction. This is in accordance with the work of Diepschlag,6 who found that the rate of reduction of iron ores by either carbon monoxide or hydrogen was much greater at higher pressures. He used pressures as high as 7 atm. In order to further understand the mechanism of the reduction of iron oxide by hydrogen it was decided to study the effect of increasing the hydrogen pressure on rebduction rates of magnetite pellets. EXPERIMENTAL PROCEDURE The dense magnetite pellets used in these experiments were made in the following manner. Reagent-grade ferric oxide was moistened with water and hand-rolled into spherical pellets. The pellets were heated slowly to 550°C in an atmosphere of 10 pct H2-90 pct CO, and held for 1 hr. They were then heated slowly to 1370°C in an atmosphere of 2 pct H2-98 pct CO, then cooled slowly in the same atmosphere. The sintered pellets were crystalline magnetite with an apparent density of about 4.9 gm per cm3. They were about 0.9 cm in diam. The porosity of the pellets, which was discontinuous in nature, was akrout 6 pct. The pellets were suspended from a quartz spring balance in a vertical tube furnace. The equipment is shown in Fig. 1. Essentially the furnace consists of a 12-in. OD stainless steel outer shell and a 3-in. ID inconel inner shell. The kanthal wound 22 in. long, 1 1/2, in. ID alumina reaction tube is inside the inconel inner shell. Prepurified hydrogen sweeps the reaction tube to remove the water vapor formed during the reaction. The hydrogen is static in the rest of the furnace. The sample is placed at the bottom of the furnace in a nickel wire mesh basket suspended by nickel wire from the quartz spring. The furnace is then sealed, evacuated, and refilled with argon several times to remove all traces of oxygen. It is then evacuated, filled with

Jan 1, 1962

By Norman Goss

IT is generally agreed that cold-working mechanically refines the grains into smaller fragments and with continued working these are oriented with certain crystallographic directions bearing a relation to the direction in which the metal is worked. Some of the energy expended on the metal during plastic deformation appears in the form of heat, but a very small portion remains in the metal as stored energy. The entropy, specific heat capacity, temperature at which recrystallization will just begin, density, ductility, elasticity, tensile strength, and resistance to corrosion are affected. These properties have been studied extensively and some of the changes in the physical properties due to cold-working were attributed to lattice distortion.1-8 The broadening of the K. lines on the X-ray diffraction diagrams of plastically deformed metals is believed to indicate lattice distortion, and consequently the existence of internal stresses. The evidence supporting this theory rests solely upon the observed experimental fact that the dif-fraction lines are broadened and the K a doublets are completely diffused. Elam9 has reviewed the matter of lattice distortion in relationship to the hardening of metals by plastic deformation. The X-ray diagrams of plastically deformed metals differ in general from annealed metals. The hardening of a metal was believed due to lattice distortion.9 The resolu-tion of the doublet is lost when a metal is cold-worked and the Lane spots are elongated. At one time this elongation was thought to indicate the elastic bending of the crystal planes. However, more careful work showed that the asterism was due to new orientations developed within the fragmented grains during plastic deformation. Some theories attrib-uted the hardening to fragmentation of the grains into smaller units.

Jan 1, 1940

With the coming of the month of 'October the various sections are beginning active work for the winter. The Colorado, Washington, Montana, and New York Sections are all doing good work in raising funds for the hospital bed at Rheims which is to be a memorial to the members of the A. I. M. E. who gave their lives in the great war. We hope that all the other sections will begin to work with this object in view and will make even a better record than they did with the Belgian Relief Fund. It was with much regret that the President, Mrs. James F. Kemp, and the Secretary, Mrs. Sidney J. Jennings, were obliged to forego the pleasure of attending the Chicago meeting in September. They were, however, ably represented by Mrs. Arthur S. Dwight who gave an informal talk after which was formed the Illinois Section, which has our best wishes for all success-" Over the top and the best of luck!"

Jan 11, 1919

By Jack Fox

Although this is going to appear in the December Issue of &E, it is being written long before the end of the year. December, of course, is the time for a summing up of the year's activities. Perhaps, the best way to begin is to report on what went on at the SME Board of Directors Meeting in St. Louis on October 20. This won't be a chronological report, and I shall take time to comment on some of the items we cover as we go along. You should be encouraged to know that your Directors take their duties seriously. Of the 21 current Directors, 19 were present, and three of the new 1971 Directors came to observe what goes on at an SME Board Meeting.

Jan 1, 1970

By H. S. McKnight

One phase of Canada's rapid development in mining and metallurgy during the past few years has been the creation of Canadian Copper Refiners Ltd., and the establishment of its modern electrolytic copper refinery at Montreal East, Quebec. Canadian Copper Refiners Ltd. is made up of three well-known metal firms whose combined activities cover the entire industry from the mine to the market. They are Noranda Mines Ltd., Toronto, Nichols Copper Co., New York, and British Metal Corporation, Ltd., London. Noranda Mines is the principal owner and provides the greater part of the raw material received by the refinery for treatment. Nichols Copper Co. designed and built the plant and is operating it under contract. British Metal Corporation acts as sales agent and markets the refinery's products. Montreal East was chosen as the site of the new refinery only after a careful survey had been made of the entire eastern part of Canada. The location chosen offers many advantages, chief of which arc the relatively low costs of power, labor, fuel and bupplies, and the fact that it is situated on Montreal harbor, the nearest seaport to the points of origin of the ram materials. All incoming material is received by rail. A majority of the plant's product is exported through the port of Montreal to European markets, being handled to the docks in railroad cars. A large proportion of the product is delivered by means of an industrial railway to the adjacent rolling mill of the Canada Wire & Cable Co., Limited. The refinery was designed to treat primarily the copper produced by Noranda Mines, Ltd. and Hudson Bay Mining &. Smelting Co., Ltd., and its rated capacity is 75,000 short tons per year. A general layout of the plant is shown in Fig. 1. Its capacity can be readily doubled, as shown by the dotted lines. Figs. 2 and 3 are sections taken through the furnace department and the tank house respectively. Except for the main office and laboratory and an auxiliary building containing the stores, warehouse, change rooms, compressor room and machine shop, the entire plant is under one roof. The type of building construction consists of reinforced concrete foundations supported on concrete piles, a steel structure covered with Robertson Protected Metal siding and a 3-in.

Jan 1, 1934

By H. B. Huntington

Some of the basic problems in understanding elec-tromigration in metals are discussed, along with the attempts that are being made to handle them. One such problem is the effect of the electrostatic forces. It is now acknowledged that the momentum exchange with charge carriers plays generally a dominant role in the driving force but the question remains to what extent the electrostatic force may still be effective. The electromigration of interstitial impurities is also an area which presents some intriguing questions. For the substitutional impurity, moving by the vacancy mechanism under the influence of an electric field, the correlation considerations are somewhat more complex than have been previously recognized. Another problem of basic importance in the calculution from first principles is the strength of the "electron friction" force, say for a simple one-band metal. A related problem growing out of the preceding is the prediction of the direction of the "electron wind" force for metals with band structure involving both holes and electrons. THE term electromigration has come to be used to describe the flow of matter in condensed phases carrying high electronic currents such as metals and alloys, whereas one usually reserves the term electrolysis for situations where the current is largely ionic, particularly in the liquid state such as molten salts. It follows that the mass transport number in electromigration is always very small, of the order of 10-7. Studies of electromigration date back some 30 years but the modern period would appear to date from the work of Seith and Wever1 who in the mid 1950's first incorporated markers to display mass motion relative to the lattice and first suggested that the direction of the mass flow was primarily determined by the sign of the charge carriers. Since that time interest in the field has grown steadily and more rapidly recently as certain technological applications became apparent. Chief of these is certainly the deleterious effects that electromigration can cause, even at relatively low temperature, to current-carrying elements in integrated circuitry.2 These phenomena have been the subject of intense study and considerable ingenuity. On the constructive side electromigration has proved a useful tool in the purification of certain metals.3 The interest of this paper is, however, centered more on the basic aspects of the subject than on its technological applications. That high electric currents should give rise to mass flow in metals and that the driving force should be more directly associated with momentum exchange with the charge carriers than with the electrostatic field are ideas that no longer cause surprise or particular interest. The field has matured to the point where the general concepts are widely accepted and continued progress in basic understanding rests on more detailed and quantitative exploration. It is the purpose of this paper to point out what are some of the current problems. As a result, we expect to raise more questions than we answer. The first of these will be the role of electrostatic forces, if any, in electromigration. A second section will deal with the electromigration of interstitials. A third and final section treats with electromigration of substitutional impurities or of the matrix atoms themselves. ELECTROSTATIC DRIVING FORCE In the conceptual treatments of electromigration it has been customary to write the driving force in terms of an effective charge number Z* and to divide it into two terms F = e£Z* = e£[Zel- z(pd/Nd)(N/p)(m*\m*\)] [1] The first of these represents the electrostatic force under immediate consideration in this section and the second and usually dominating term for metals arises from momentum exchange with charge carriers, commonly called the "electron drag" term. As can be seen it is set proportional to the electrons per atom, z, and the ratio of the specific resistivity of the moving entity to the corresponding resistivity per matrix atom. The (m*/Im*I) factor takes into account the fact that the sign of the charge carrier determines the sign of the driving force. The specific resistivity of the moving entity is averaged over its path. In the case of motion of the matrix atoms by vacancies this gives rise to approximately one-half the resistivity at the saddle point since the scattering power of the atom at its equilibrium position bordering the vacancy differs only slightly from that of a normal matrix atom. Although the formulation of the "electron drag" term in Eq. [I] is based on a highly simplified model for electron defect scattering, the essential features implicit in the expression are common to all the theoretical approaches that have so far appeared in the literature.4-6 As for Zel, most treatments of electromigration have included the quantity as the parameter which measures the direct interaction of the electrostatic field with the ion and equated it to the nominal valence of the latter. However, there has been considerable discussion whether this interaction may not be 0 in many cases.6 If the moving ion is always enveloped by the same distribution of shielding charge, then clearly its motion will not involve any work done by the electric field and one can expect there will be no electrostatic force exerted on such a neutral composite. From this point of view the shielding charge around the ion would be said to be complete and hence the entity within the Debye shielding sphere would be unaffected by the electrostatic field per se. There is, however, the prospect that, as the moving ion progresses, new charge comes in to participate in the shielding action

Jan 1, 1970

By W. W. Gerberich, P. L. Hemmings, V. F. Zackay

ThE strain-induced martensitic transformation may be used to attain desirable combinations of strength, ductility, and fracture toughness. One of the parameters is the relative stability of the austenite. For example, it has been shown by Zackay et al.1 that the volume percent of strain-induced martensite is related to the combination of strength and elongation obtained. It has also been shown that the degree of transformation is an important factor in the crack propagation resistance of metastable austenitic steels.2 Considering both tensile and crack-propagation tests, it was of interest to see if there was any functional relationship between the amount of strain and the volume of strain-induced martensite. Previously,9 it had been shown that at room temperature, there was a relationship between uniaxial tensile strain and the volume percent of resulting martensite given by The data were obtained by plastically elongating tensile samples to a certain strain and then measuring the field strength to determine the strain-induced ferromagnetic volume. This was accomplished for two conditions having yield strengths of 229 and 233 ksi. The nominal composition of this material was 9Cr-8 Ni-3 Mo-2 Mn-2 Si-0.25 C-0.09 N. In evaluation of the strain-induced martensite at a crack tip: the question arose as to whether Eq. [1] would also be valid under triaxial stress conditions. Tests were conducted on 1/2-in. thick plate material having a composition of 9 Cr-8 Ni-4 Mo-2 Mn-2 Si-0.27 C. It was found that sectioning, polishing, and etching of fractured specimens could reveal the strain-induced martensite occurring at a crack tip. Care had to be taken to minimize the final polishing steps so as to avoid a smeared layer of strain-induced martensite. The method for taking metallo-graphic samples from fractured crack-line loaded type samples is shown in Fig. 1. Observations of the strain-induced martensite occurring at room tem-

Jan 1, 1970

By C. D. Woodward

PRIOR to 1902, the tramming of ore from the stopes to the shafts, in the Butte mines, was done by man or animal power, but the demand for greater tonnage and the need for more improved methods of tramming the ore resulted in the installation of the compressed-air locomotive in a few mines. Some of the objections to animal haulage were thus eliminated, but this locomotive was not generally adopted, because of a number of limiting features. It was superseded by the electric trolley locomotive. The early types of trolley locomotives were not satisfactory from the operators' viewpoint, but. they had many economic advantages and after a number of years, in which improvements were constantly made in the structural details, they became dependable, so that the use of animals for main haulage in the mines has now been practically abandoned. There are now operating in the Butte mines of the Anaconda Copper Mining Co., 185 trolley-type locomotives, each of which has replaced five animals. It cost approximately $50 per month to keep an animal, hence the economies that resulted fully justified the expenditure of electrifying the haulage systems. The haulage conditions in this company's mines possess many advantageous features that are not always found in underground mine workings. The drifts and crosscuts are large, approximately 5 ft. (1.5 m.) wide by 7 ½ ft. (2.3 m.) high, and have curves of no less than 18 ft. (5.5 m.) radius; and the roadbeds of the drifts and crosscuts have a uniform grade of 0.5 per cent. toward the shaft, or in favor of the loaded trips. In all of the mines, except two, the track gage is 18 in. (45.7 cm.), and all tracks in the main haulageways are laid with 25-lb. (11.3 kg.) rails. The stations at the shaft are large, well-lighted, clean, and cool. The average temperature of ,the stations, however, is about 75° F. (24° C.), while the average temperature in some of the drifts and crosscuts is 92° F. (33.5° C.).

Jan 2, 1922

By Atmaram H. Soni

A statistical study of machinability led the writer to examine existing data in regard to a thermal conductivity-mechanical properties relationship. Various functional relationships were proposed and the multiple correlation determined by statistical methods discussed in detail in the 1iterature.4 The relationship having the greatest engineering and statistical significance is discussed below. The data for cast and wrought aluminum alloys''2 have been compiled and analyzed separately. The results of these analyses are presented in Table I. The empirical equations for estimating the thermal conductivity (cal sec-' cm-I °C) are: for cast aluminum alloys K = 0.584 -0.00984/ -0.00263 Hb [1] and for wrought aluminum alloys K = 0.604 -0.00424l- 0.00170 Hb [2] where 1 and Hb are the percentage elongation and Brinell hardness number. Results of a similar analysis pertaining to stainless steel3 are also given in Table I. This empirical equation for estimating thermal conductivity (Btu per sq ft per hr per °F per in.) is K = 216.19- 1.716l - 0.0997 Hb [3] The relationship between electrical resistivity and mechanical properties was also examined for aluminum alloys using the same statistical method. These results are listed in Table II. While the situation of exact multiple correlation

Jan 1, 1965

Discussion of the paper of E. W. Parker, presented at the New York meeting, February, 1913, and printed in Bulletin No. 75, March, 1913, pp. 443 to 451. A MEMBER :-I would like to call attention to the fact that the speaker has failed to indicate where is the center of gravity of the membership of the Institute, while he is dealing with this map. MR. PARKER :-I think you will find that a little further east. CHAIRMAN JAMES F. KEMP :-In connection with Mr. Parker's paper, I would like to inject a little matter of history into our program here, as regards the founding of the Institute. The credit for the founding of the Institute really applies to miners who were engaged in the anthracite coal region. The three men who signed the circular for the call for the meeting which brought the engineers to Wilkes-Barre in May, 1871, were Eckley B. Coxe, Richard P. Rothwell, and Martin Coryell.

Jan 5, 1913

F. McMillan Stanton was born in New York City on May 23, 1865, the son of an English father and of a mother whose family was linked with that of Peter Stuyvesant. Mr. Stanton took his degree from the School of Mines of Columbia University in 1887, worked for two years as an assayer and surveyor and then went into the mining field on his own account. After a few years, he was offered a position with the Atlantic Mining Co., and began the work which was to continue with marked success for twenty-three years. In 1910, Mr. Stanton retired and went to Europe for a rest. Upon his return in 1914, he was elected treasurer and director of the Mohawk Mining Co., the Wolverine Copper Mining Co. and the Michigan Copper Mining Co., to which group was later added the White Pine Extension, Copper Co., and continued to serve these companies until the time of his death, Sept. 12, 1916.

Jan 12, 1916

By N. Mungan

Formation damage, i.e.. reduclion in permeability, has been generally attribuled to clay minerals which expand or disperse upon contact with water that is less saline than the connate water. Luboratory, studies show that penneahility reduction can also occur in formalions containing only nonexpandable clays such as illite or kaolinite, and can be caused also by changes in pH. Furthermore, pH changes can damage even formations that are essentially free of clays. It is suggested that permeability reduction is due to the small passages being blocked by particles, which may be dispersed clays, cemenlion material or other fine parricles. These particles are dislodged by dispersion of clays due to changes in salinity or by dissolution of calcareous cement by acids, or of silicaceous cement by alkaline solutions. In working with reservoir cores, it was found that extracted cores damaged more easily and extensively than nonextracted cores. The extent of damage depended also on tenlperatltre. INTRODUCTION Permeability is an important property of porous media and has been the subject of many studies by engineers and geologists. Many of these studies are conccrned with formation damage, i.e., reduction in permeability, resulting from exposure of oil-producing formations to water substantially less saline than the connate water. This effect causes understandable concern since during drilling, completion and production phases formations are often exposed to fresh water. The damage resulting from contact with relatively fresh water has been attributed to expansion and dispersion oF clay minerals. During laboratory investigation of the use of NaOH as a wettability reversal agent to increase oil recovery from oil-wet reservoirs, several cores used in the displacement studies suffered loss in permeability. Despite the traditional usage of NaOH for conditioning aqueous mud systems, the role of the caustic filtrate in wellbore damage seems to have been overlooked. Browning2 as recently reported on the effects of NaOH in dispersing clay minerals but he was concerned only with complications that may arise in drilling massive shale beds. The following study was made to examine the role of pH and salinity changes in core damage. Where cores from reservoirs were used, tests were performed with extracted and nonextracted cores both at room and reser- voir temperatures, since it was felt that the test environment and core condition may affect the results. Because of its limited coverage and exploratory nature, this study is not intended to provide answers to field formation damage problems. It is hoped that it will encourage research into new aspects of the permeability reduction problems, particularly those allied to new recovery and production processes. PROCEDURE In all permeability tests, fluids were pumped through the cores at a constant volumetric rate. Only deaerated fluids and reagent grade chemicals were used. The fluids were passed through two ultrafine filters before injection to remove any entrained particles. The cores, with the exception of the unconsolidated cores, were mounted in Hassler holders. Water was used to transmit pressure to the sleeve. The inlet endpiece had two entry ports which permitted scavenging one fluid with another to avoid any mixing in the small holdup volume. The cores were flushed with CO2 gas, evacuated for 5 to 6 hours and saturated with the first liquid at a pressure of 1,000 psi for 24 hours to eliminate any free gas from the cores. Pressure differences up to 20 psi were measured by transducers, calibrated in inches of water and continuously recorded. For greater pressure drops, gauges were used. All reservoir cores were cleaned with a light refined mineral oil, then with heptane, and finally dried with CO2. Compatibility tests showed that no precipitates formed when mineral oil and the crudes were mixed. Some cores were extracted in Dean-Stark-type solvent extractors using xylene and trichloroethane and dried in a vacuum oven at 450F. Each test consisted of a sequence of water, test solution, and again water flow. RESULTS AND DISCUSSION STUDIES IN BEREA CORES Salinity Contrast Berea cores 2-in. in diameter and 12-in. long were cut from sandstone quarried in Cleveland, Ohio. The clay minerals were identified by X-ray diffraction to be chlorite, kaolinite, illite and incerlayered illite. Flow of fresh water or 30,000 ppm brinc does not cause any permeability reduction (Fig. 1). However, after injection of brine the core is readily damaged by fresh water. Damage starts almost instantly as the fresh water injection is begun, and at a cumulative injection of 1.2 PV fresh water, the permeability has dropped from 190 to 0.9 md. Upon continued injection, the effluent contains clay minerals dislodged from the core. The final core per-

Jan 1, 1966

By David Sinclair, Philip B. Bucky

THE dimensions and shapes of mine structures may at present be determined by (1) field experience, (2) structural calculations, and (3) barodynamic tests.§ None of these, however, provide information as to the stresses, their direction and distribution in a mine structure. For the design of pillars, the placing of openings relative to working places such as gangways, haulage levels, etc., this information is desirable. Photoelastic methods provide this and, while relatively new, their application in all engineering fields is assuming increasing importance. This paper, therefore, will present the method with a few applications to mining, and with sufficient reference for further study by the reader. PART I THE PHOTOELASTIC METHOD The photoelastic method of stress measurement determines the stress distribution in a two-dimensional model by optical means. It makes use of the fact that when a piece of isotropic transparent material, such as glass, celluloid, or Bakelite, is stressed and viewed in polarized** light a picture is seen which indicates by its color bands of light, or fringes, the magnitude of the stresses, their direction and their distribution. GENERAL EXPLANATION The stress at any point 0 in a structure (Fig. 1), may be resolved into two components, P and Q, each a pure tension or compression, at right angles to each other, called principal stresses.1 To fully identify the stress, the values of P and Q and their directions or angle [0] must be known.

Jan 1, 1940

By J. T. Brown

AS far as could be ascertained, no one had previously investigated the creep strength of silicon poly-crystals. Literature has appeared showing evidence for plastic deformation in silicon single crystals and whiskers.*1"6 Also the fact that germanium, a material of similar crystal structure to silicon undergoes plastic deformation under stress at temperatures above about 60 pct of its melting temperature, has been known for some time.2"4'7 This investigation was performed for the purpose of determining the strength and ductility of silicon polycrystals under creep conditions that would give fairly long times to rupture. PROCEDURE The silicon specimen blanks were obtained by first placing granulated transitor grade silicon (99.999 + pct pure) in a silica crucible. The crucible was surrounded by a graphite susceptor, and induction heating was used for melting the silicon in a vacuum furnace. Blank specimens were formed by freezing molten silicon onto a polycrystalline seed of silicon in a vacuum furnace. The seed was attached to a motor driven revolving rod. As silicon solidified, this rod was gradually withdrawn from the melt. A shape with a contracted center section was obtained by varying the rate of withdrawal from the melt. Specimens for the creep-rupture tests were ground from these "pulled" blanks. Creep-rupture tests were performed in spring loaded machines under constant load at 1800" and 2000° F. RESULTS AND DISCUSSION A test specimen which was sectioned longitudinally is shown in the photomacrograph in Fig. 1. Very little deformation has taken place in the portion of the specimen shown, however, slip lines from several slip systems within the same grain, and deformation band formation was seen. The elongated appearance of the grains is due to the method of growing the specimens. One of the most interesting aspects of the results obtained from the creep-rupture tests was the high strength and the accompanying large amount of ductility. The data obtained is listed in Table I which shows the stress to rupture in 100 hr at 2000°F is between 8000 and 9000 psi. This indicates that silicon's strength at 2000°F is about equal to that of the best commercial super-alloys. It is important to mention that silicon has less than 1/3 the density of iron-, nickel-, and cobalt-base alloys. The usual type alloys for high-temperature applications

Jan 1, 1960

By AIME AIME

FRANK T. SISCO is a native of Lawrence, Kansas. He received his earlier education in Clinton, Iowa and his university training at the University of Illinois. His experience in the steel industry has included service in the chemical, testing, and metallurgical departments of the Illinois Steel Co., of South Chicago; the Hess Steel Corp., of Baltimore; the IJ. S. Naval Ordnance Plant at Charleston, W. Va.; and the American Steel and Wire Co., Waukegan, Ill. He severed for seven years as chief of the metallurgical laboratories of the U. S. Army Air Corps at Wright Field, Dayton, before coming to New York in 1930 to become metallurgist and editor of the Alloys of Iron Research, the position he now holds.

Jan 1, 1940

By W. F. Guenther

The usual hand-operated drilling outfit consists of a 4-in. post-hole auger with 3/4,-in. pipe for drill stem, in 4-ft lengths, with a turning handle fitted to a top pipe T. The auxiliary tools are: a chisel-bit drill made from 3/4 or 7/8-in. tool steel welded to a 4-ft length of 3/4-in, pipe, so that the regular pipe string can be used; also a churn or "mule foot" made from 3-in. pipe, slotted on one side, belled to a 4-in. tempered cutting edge on the bottom, all welded to a 3/4-in. coupling by a yoke. Other tools required are pipe wrenches and cleanout tools made from old auto springs (Fig I). A 4 1/2 or 5-in. collar welded to a plate is often used to protect the mouth of the drill hole. In general the auger is used in the typical clay overburden and brown phosphate matrix, which is relatively soft. The churn or "mule foot1' is used in hard pan, lump phosphate or cherty ground. The drill is used for breaking flint, often found loose in the overburden. The drill with the chisel bit is used for trimming sides of the hole, sounding for lime bottom and breaking through hard lumps. Holes have been drilled to a depth of 80 ft, but the limit of efficient operation is about 50 ft. In deep holes it is necessary to unscrew the string in 20-ft lengths, to

Jan 1, 1948

By W. F. Guenther

The usual hand-operated drilling outfit consists of a 4-in. post-hole auger with 3/4,-in. pipe for drill stem, in 4-ft lengths, with a turning handle fitted to a top pipe T. The auxiliary tools are: a chisel-bit drill made from 3/4 or 7/8-in. tool steel welded to a 4-ft length of 3/4-in, pipe, so that the regular pipe string can be used; also a churn or "mule foot" made from 3-in. pipe, slotted on one side, belled to a 4-in. tempered cutting edge on the bottom, all welded to a 3/4-in. coupling by a yoke. Other tools required are pipe wrenches and cleanout tools made from old auto springs (Fig I). A 4 1/2 or 5-in. collar welded to a plate is often used to protect the mouth of the drill hole. In general the auger is used in the typical clay overburden and brown phosphate matrix, which is relatively soft. The churn or "mule foot1' is used in hard pan, lump phosphate or cherty ground. The drill is used for breaking flint, often found loose in the overburden. The drill with the chisel bit is used for trimming sides of the hole, sounding for lime bottom and breaking through hard lumps. Holes have been drilled to a depth of 80 ft, but the limit of efficient operation is about 50 ft. In deep holes it is necessary to unscrew the string in 20-ft lengths, to

Jan 1, 1948

By John Gann

THE following investigation constitutes a brief resume of the more important binary magnesium alloys from the standpoint of metallographic technique, and the effect of heat treatment on structure and properties. The comparative newness of the subject justifies this procedure as a preface to a more detailed study of each individual series of alloys. The work was started with the idea of practical application in the industry rather than as a theoretical investigation. The alloy compositions studied were selected as those most likely to show whether heat treatment would produce beneficial results. Furthermore, it was considered satisfactory to use commercial 99.9 per cent. magnesium, the best commercial grade of alloying ingredients, and to limit the time of heat treatment at the expense of incomplete equilibrium. These facts must be kept in mind when examining the results obtained, and the conclusions drawn.

Jan 1, 1928

By M. H. Caron

D. C. Ralston—The fact that none of the organizations that have worked on these ammoniacal leaching processes have contributed discussion of Mr. Caron's papers today is a matter of some disappointment. Adaptations, modifications and improvements have been made by several organizations or individuals and to complete the record I want to document a number of them. The Nicaro Nickel Co. operated a Government owned plant at Nicaro, Oriente, Cuba, during the past war. A report on the project was written for Reconstruction Finance Corp. and is in the document file collected by the Office of Technical Services, Commerce Department and filed with the Library of Congress, where it can be consulted or bibliofilm or photostat copies obtained by asking for copies of PB 97271. Nicaro Nickel Co. has obtained a series of U.S. Patents, my list (probably incomplete) of which bears the following numbers: 2,400,098; 2,400,114; 2,400,115; 2,400,461; 2,400,612; 2,458,902 and 2,473,795. International Nickel Co. has also studied the problem and U.S. Patent 2,478,942 shows that some of the complications involving occasional low extractions have been unraveled. Forward, Samis, and Kudryk, of the University of British Columbia, have also published a study of copper-nickel sulphide concentrate.' Others are interested and it is evident that this type of hydrometallurgy is likely to find a happy application in the not-too-far distant future. Caron's two papers practically amount to a summation of his life's work on the important subject of nickeliferous iron ores and the American Institute of Mining and Metallurgical Engineers is fortunate to have been chosen the medium of publication. M. Rey—The ammonia leaching process has been the subject of certain studies in New Caledonia, but at the present time, the conditions are not very favorable to its adoption. The process is a combination of a thermal and a hydrometallurgical process. As a result, the first costs and the operative costs are rather high. To counteract this unfavorable situation, it would be necessary to make a very high extraction. But unfortunately, the process is delicate and in spite of all of Caron's valuable work, there are still many unknown factors. It is difficult to obtain regularly a high extraction, exceeding 75 to 80 pct. It would be interesting to have the opinion of Inter-national Nickel on the process and to know what the Dutch are doing in Celebes. M. H. Caron (author's reply)—I am quite familiar with the different types of nickel and cobalt ores as found on New Caledonia, and it may be pointed out that the Celebes ores are quite the same in their properties. Their behavior when treating the ores by the ammonia-leaching process is also alike and in my opinion, there is no reason why a high extraction of the New Caledonian ores could not be obtained if the process is properly applied. For the sake of completeness I may add that one of my patents has not been discussed in the papers. This patent deals particularly with the treatment of serpentine nickel ores. (Netherlands No. 62693 40a, French No. 965.786 April 21. 1948. and Cuban No. 13.625 Jan. 1950.) O F. A. Forward, C. S. Samis, and V. Kudryk: Trans. Canadian Institute of Mining and Metallurgy. (1948) 151 (Bull. 434) 350-355.

Jan 1, 1951

By L. Webster Wickes

The bad effects of arsenic in commercial copper are well-known to metallurgists. The refining of copper by electrolysis eliminates practically all of the arsenic, provided certain requirements are fulfilled. The first, and most important, of these requirements is, that the voltage of the depositing current shall not be too high. It has been known for some time that the percentage of arsenic in the deposited copper increases with the voltage. To investigate the relation between the electro-motive force (e.m.f.) and the freedom of the precipitated copper from arsenic, the experiments were made, of which a brief summary is here given: I made three copper-arsenic alloys, containing respectively 3.56, 2.24 and 0.96 per cent. of arsenic. From these alloys I cast several anodes. For cathodes I used sheets of thin copper,

Jan 1, 1905