Search Documents

By C. S. Smith, W. M. Williams

THE quantitative study of grain shape in three dimensions has been a difficult one from the practical standpoint. Experiments on grain shape have usually been based on indirect observations of two-dimensional metallographic samples or on grains separated by intergranular corrosion or fracture. The latter method was used in particular by Deschl in 1919 in observing the shapes of ß-brass grains which had been separated with mercury. The similarity in detail of shape and packing that exists between bubbles in a soap froth and metal grains was noted by Desch who remarks that: "Surface tension has an. important share in determining the form of the crystal grains in a solidifying metal and such grains have a tendency to assume the shape of foam cells." More recently the relation between grain shape and grain growth has been studied by Harker and Parker.' The importance of surface tension forces in determining microstructure has been discussed by Smith," and an analysis of the topologi-cal rules that apply to such structures has been made by the same author.' Biologists have made valuable contributions to the general problem of shape and form in an assembly of space-filling cells subject to surface tension forces. Particular mention must be made of the extensive researches of Lewis5,8 on botanical and anatomical tissues, and Matzke and Nestler,7,8 who have made painstaking studies of bubble shapes in different kinds of foam. The present paper introduces a new method of studying individual grains in particular alloys—a method which may well find use in other metallurgical researches, and which seems also to be applicable in biological problems. Metal Grains in Three Dimensions The individual grains in a piece of metal or the bubbles in a soap froth must satisfy two conditions —they must be in juxtaposition so as to fill space and their interfaces must conform to the laws of surface tension. If a further restriction is imposed, namely, that only one type of polyhedron be used, then the sole possibility is an assembly of "minimal" tetrakaidecahedra," each polyhedron having eight doubly-curved hexagonal faces and six plane quadrilateral faces, the angles between adjacent faces being 120". Such cells could be stacked on a body-centered cubic lattice and would be quite stable. For many years it was believed that soap bubbles actually possessed the shape of this ideal body, and the hypothesis was the starting point for several investigations on the shapes of soap bubbles, biological cells, and metal grains. These investigations have shown, what might have been obvious in the beginning, that if the condition of symmetry is relaxed the tetrakaidecahedron is almost never found. If we retain only the rule that all contacts should be in local surface tension equilibrium and that the assembly should fill space, metal grains may then take a nearly infinite variety of shapes and no single one may be regarded as an archetype. These two conditions, which are fully discussed in one of the previously mentioned papers,' lead us to think of a typical grain in an annealed metal as having the following characteristics: 1—A grain may have any number of faces, but usually between nine and eighteen. The faces (each of which is, of course, shared by two grains in the assembly) may have any number of edges, but usually between four and six. Pentagons are by far the most frequent. 2—In the assembly of grains each edge is shared by three faces and by three grains. Each vertex is a point shared by four grains, six faces, and four

Jan 1, 1953

By W. C. Leslie

W. C. Leslie (Edgar C. Bain Laboratory for Funda mental Research)—This investigation, with its com bination of high-purity metal, calorimetry, and metallography, will serve as a model for annealing studies for a long time to come. The evidence for a competition between recovery and recrystalliza-tion is particularly convincing. The demonstration of edge-nucleated recrystallization was so clear that it may obscure the necessity for other types of "nucleation" sites; otherwise, single crystals of aluminum could not be recrystallized after cold work. At least three types of sites have been found to operate in iron: 1) high-angle boundaries, probably in the same manner as in aluminum, 2) matrix sites, 3) inclusions or second-phase particles. In each instance, the cells developed during cold work and perfected during recovery are the "nucle for recrystallization. Observations by ourselves and others of the dislocation structure of cold-worked metals and of the structural changes that occur during annealing have led us to doubt the validity of the basic assumption of the Lucke-Detert theory, and of the modification developed by Gordon and Vandermeer, that during recrystallization of a metal containing foreign elements in solid solution a high-angle boundary is ad vancing into a cold-worked matrix having a random distribution of solute atoms. We contend that an es sential part of the cold-working and annealing of solid solution alloys is the trapping of solute atoms by the low-energy "wells" afforded by individual dislocations and by dislocation arrays. If cells are formed during cold work, the cell walls are stabilized by this concentration of solute atoms. Thus, solutes inhibit recrystallization not only by decreas-ing the rate of high-angle boundary migration, but also by preventing the formation of high-angle boundaries by subgrain growth or coalescence, i.e., solutes can inhibit both "nucleation" and growth. In addition to stabilizing the dislocation Structure, the solute-dislocation interactions may produce clusters of solute atoms which are not as readily assimilated into the recrystallized grains as are individual solute atoms. There is an additional complication. The dislocation structure formed upon cold working a dilute solid solution may not be the same as that formed during cold working of the pure solvent metal. The solute can either enhance or minimize the formation of cells during cold working. Both effects have been observed in binary alloys of iron. The annealing process is inextricably connected with the mechanisms of strain hardening and solid solution hardening. Although the correlation between experimental boundary migration rates and the predictions made from the theoretical equations are impressive, it should be mentioned that in at least four other instances (Pb-Ag and pb-Au,15, Fe-Mn,16, Fe-Mo)17 the agreement was rather poor. In brief, while it is probable that the migration of high-angle boundaries is held back by solutes in the manner described, this is only a partial explanation of the total effect of solutes upon recrystallization of cold-worked alloys. Paul Gordon and R. A. Vandermeer (author's reply)— The authors first wish to thank Dr. Leslie for his compliments of this work. It is perhaps worth pointing out that some of Dr. Leslie's remarks are directed toward subject matter covered in two earlier papers in our work.18,19 We agree with Dr. Leslie's main contention that the exact nature of the metal structure in the vicinity of a boundary should have an effect on the boundary migration. The theory of Lucke and Detert does not take such detail into account, nor does it account for orientation effects on the migration rates. We assume that since our data checks the theory so well, the effects of detailed structure are statistically averaged out by the polycrystalline techniques used just as are the effects of orientation factors.

Jan 1, 1963

By R. B. Snow

This paper describes a technique of polishing and etching specimens of open-hearth furnace slags or hearth aggregates for identification of the crystalline constituents —lime (CaO), tricalcium silicate (3CaO.SiO2), dicalcium silicate (2CaO.-SiO2), rnonticellite (CaO.MgO.SiO2), or forsterile (2MgO.SiO2), with especial em-phasis on the mineral merwinite (3CaO.-MgO.2SiO2). With proper standardization, this identification does not require the use of the petrographic microscope. The composition of basic open-hearth slags and furnace bottoms falls, almost without exception, within systems containing CaO, MgO, 'IFeO,,, MnO and SiOz, in which the number of basic molecules so greatly exceeds the orthosilicate ratio (two molecules of base to one of silica) that free basic oxides, and combinations between them such as alumi-nates or ferrites, are present in cooled specimens. Orthosilicates of (CaO + NgO) are the most common in such specimens, since in nearly all cases, except premelt slags, the molecular ratio of (CaO + MgO) to SiO, is more than 2 to I. When sufficient lime is available it combines with the silica to form dicalcium silicate (2Ca0.Si02), which contains little, if any, IvfgO, FeO or MnO in solid solution whereas the latter oxides combine to form the oxide solid solution known as periclase. If the lime present is insufficient to form dicalcium silicate (2Ca0.Si02) it combines with Mgo to form either merwillite or moIlticellite (SiOz); these minerals take little if any FeO or MnO into solid solution and the remaining MgO, FeO and hInO combine as periclase. This generalization seems to be valid for basic slags and furnace bottoms, since minerals such as Ca0.MnOSi02 and CaO.FeO.SiOz are found only in slags in which the lime-silica ratio is less than 2 and are not observed in 'pecimens from furnace bottoms. The identification of crystalline constituents in such materials, especially of fine crystals in the groundmass, is difficult under the petrographic microscope. They are often masked by their neighbors because of their small size in relation to the thickness of the thin section and because of the presence of Opaque Or colored constituents. The indices of refraction and the optical sign of the mineral are sometimes difficult to determine because of the small size or because Of twinning or of inclusions within the crystal. Moreover, the positive identification of merwinite (3Ca0.Mg0.2Si02) from its optical properties is usually difficult in the presence of dicalcium silicate (zCaO.SiO2). CaO, MgO, jCa0.Si02 and 2Ca0.SiOz in open-hearth 'lags have been identified for a number of years in the U.S. Steel Corporation Laboratory by the usual

Jan 1, 1948

By R. B. Snow

This paper describes a technique of polishing and etching specimens of open-hearth furnace slags or hearth aggregates for identification of the crystalline constituents —lime (CaO), tricalcium silicate (3CaO.SiO2), dicalcium silicate (2CaO.-SiO2), rnonticellite (CaO.MgO.SiO2), or forsterile (2MgO.SiO2), with especial em-phasis on the mineral merwinite (3CaO.-MgO.2SiO2). With proper standardization, this identification does not require the use of the petrographic microscope. The composition of basic open-hearth slags and furnace bottoms falls, almost without exception, within systems containing CaO, MgO, 'IFeO,,, MnO and SiOz, in which the number of basic molecules so greatly exceeds the orthosilicate ratio (two molecules of base to one of silica) that free basic oxides, and combinations between them such as alumi-nates or ferrites, are present in cooled specimens. Orthosilicates of (CaO + NgO) are the most common in such specimens, since in nearly all cases, except premelt slags, the molecular ratio of (CaO + MgO) to SiO, is more than 2 to I. When sufficient lime is available it combines with the silica to form dicalcium silicate (2Ca0.Si02), which contains little, if any, IvfgO, FeO or MnO in solid solution whereas the latter oxides combine to form the oxide solid solution known as periclase. If the lime present is insufficient to form dicalcium silicate (2Ca0.Si02) it combines with Mgo to form either merwillite or moIlticellite (SiOz); these minerals take little if any FeO or MnO into solid solution and the remaining MgO, FeO and hInO combine as periclase. This generalization seems to be valid for basic slags and furnace bottoms, since minerals such as Ca0.MnOSi02 and CaO.FeO.SiOz are found only in slags in which the lime-silica ratio is less than 2 and are not observed in 'pecimens from furnace bottoms. The identification of crystalline constituents in such materials, especially of fine crystals in the groundmass, is difficult under the petrographic microscope. They are often masked by their neighbors because of their small size in relation to the thickness of the thin section and because of the presence of Opaque Or colored constituents. The indices of refraction and the optical sign of the mineral are sometimes difficult to determine because of the small size or because Of twinning or of inclusions within the crystal. Moreover, the positive identification of merwinite (3Ca0.Mg0.2Si02) from its optical properties is usually difficult in the presence of dicalcium silicate (zCaO.SiO2). CaO, MgO, jCa0.Si02 and 2Ca0.SiOz in open-hearth 'lags have been identified for a number of years in the U.S. Steel Corporation Laboratory by the usual

Jan 1, 1948

By Albert Wiggin

THE copper-bearing sulphide ores from the mines in Butte, Mont., which are for the most part concentrated at the Boston & Montana duction Works in Great Falls and at the Washoe Reduction Works in Anaconda, contain the following minerals of economic value: Chalcocite, Cu2S; enargite, Cu3AsS4; cupriferous pyrite; bornite, Cu3FeS3; covellite, CUS; tetrahedrite, 4 CuS2Sb2S3; and tennantite, Cu8AsS7;. All of the ores carry a high percentage of pyrite. Many of the above sulphides are argentiferous and also carry from 10 to 20 cts. per ton in gold. The gangue is quartz and highly altered granite, with sphalerite and galena and more rarely barite and hubnerite as accessory minerals. An average chemical analysis of the second-class ore concentrated at Great Falls and Anaconda would be as follows: Copper 3.2 to 3.4 per cent. Silver 2. 3 to 3.0 oz. per ton. Gold 0.0-1 to 0.15 oz. per ton. Si02.. 55 to 60 per cent. FeO 12 to 15 per cent.. Sulphur 12 to 1.5 per cent. Al2O3, S to 10 per cent. CaO 0.5 to 0.8 percent. As203, 0.5 to 0.6 percent. Lead 0.2 to 0.3 percent. Before describing the Great Falls flow sleet as installed, at Anaconda, a brief history of the Great Falls concentrator will be given, including a description of the various concentrating machines and systems which have been tested in the search for a flow sheet which would give a higher recovery of copper.

Jan 8, 1913

By R. L. Skaggs, D. T. Peterson

The effect of carbon in solid solution on the plastic behavior of thorium was studied by measuring the flow stress of Th-C alloys from 4.2" to 573°K and at several strain rates. Carbon was found to strengthen thorium primarily by increasing the thermally activated component of the flow stress. The strengthening due to carbon was directly proportional to the carbon content and decreased rapidly with increasing temperature up to 423" K. The flow stress also increased with increasing strain rate. The strengthening appears to be due to a strong short-range interaction between carbon atoms and dislocations. A yield point was observed in the Th-C alloys which increased with increasing carbon content. JTREVIOUS study of the mechanical properties of thorium has been confined largely to the measurement of the engineering properties. Work prior to 1956 has been summarized by Milko et al.1 who reported that additions of carbon to thorium sharply increased the room-temperature strength. In addition, the yield strength was observed to decrease rapidly over the temperature range from 25" to 500°C. In 1960, Klieven-eit2 measured the flow stress of thorium containing 400 ppm C. He found that over the temperature range from 78" to 470°K the flow stress was strongly dependent on temperature and rate of deformation. A drop in the load-elongation curve, or a yield point, was observed over most of the above temperature range. Above 470°K, the flow stress was nearly independent of temperature and strain rate. This strong temperature and strain rate dependence of flow stress is not generally observed in fcc metals. It is, in fact, more typical of the behavior reported for bcc metals. Bechtold,3 Wessel,4 and conrad5 have pointed out the striking difference between the commonly studied bcc metals and fcc metals in regard to the effect of temperature and strain rate on the flow stress. Zerwekh and scott6 studied the plastic deformation of thorium reported to contain 12 ppm C. They found that this material did not obey the Cottrell-Stokes law as expected for fcc metals. In addition, they found values of the activation volume smaller by an order of magnitude than expected for an fcc metal. They concluded that thorium was strengthened by a randomly dispersed solute. Thorium differs from many other fcc metals that have been studied extensively in that it shows a relatively high carbon solubility at room temperature. Mickleson and peterson7 report the solubility limit at room temperature to be 3500 ppm C. The lowest value reported is that of Smith and Honeycombe8 who report the limit to be 2000 ppm C at 350°C. The pres- ent investigation was a systematic study of the flow stress and yield point phenomenon of thorium over a broad range of carbon content, temperature, and strain rate. EXPERIMENTAL PROCEDURE The thorium used in this investigation was produced by the reduction of thorium tetrachloride with magnesium as described by Peterson et a1.' Chemical analysis of the original ingot after arc melting and electron beam melting is shown in Table I. Alloys were prepared by arc melting this thorium with high-purity spectrographic graphite. Threaded specimens with a gage length 0.252 in. diam by 1.6 in. long were used for the constant stress or creep measurements. These specimens were machined from rod which had been cold-rolled and swaged to % in. diam. Tensile specimens were prepared by swaging annealed 3/8 -in.-diam rod to 0.102 *0.001 in. The as-swaged wire was cut to lengths of 2 in., annealed, and the center 1-in. gage length elec-tropolished to 0.100 ±0.001 in. The specimens were gripped for a length of 3 in. at each end by a serrated four-jaw collet which was tightened by a tapered compression nut. No slipping occurred in the grips and negligible deformation was observed outside the 1-in. gage length. Both the creep and tensile specimens were annealed at 730°C under a vacuum of 1 x X Torr. The resulting structures consisted of equiaxed recrystallized grains with a grain size of 3200 grains per sq mm for the tensile specimens and 2200 grains per sq mm for the creep specimens. After the specimens were prepared, samples were analyzed for nitrogen, oxygen, and hydrogen. The results of these analyses are given in Table 11.

Jan 1, 1969

By William B. Plank

ENROLMENT data given in this report of the seventh study of the schools by the Mineral Industry Education Division reveals the critical situation in the mineral engineering schools of the United States. Complete figures for the year 1942-43 show that at that time, about one year after Pearl Harbor, the enrollment of mineral engineers was 6385 or 30 per cent less than in 199441. By October 1943, however, enrollment had dropped to 2050, as reported in the Journal of Engineering Education of January 1944. This was a further reduction of 68 per cent in one year, or 77 per cent in three years. With accelerated programs in effect during the current year, with many graduations since last October, and with the military forces taking practically all the high school graduates, the present enrollment is, of course, much lower than the 2050 above given. There are no late data on the exact situation. In Canada, the same situation exists in the mineral engineering schools, only

Jan 1, 1944

By G. Das, S. V. Radcliffe

The substructural features developed in tungsten as a function of annealing temperature (up to 2200°C) and type of material [undoped and doped powder metallurgy (PM) tungsten and electron beam melted tungsten] have been investigated by transmission electron microscopy. For doped PM tungsten wires, characteristic "par-ticulate" substructural features developed rapidly with increase in annealing temperature above 700°C. The features consisted of parallel rows of elongated or circular shapes (500 to 1000A diam) lying along the direction of the wire axis and were identified as internal voids by diffraction contrast experiments. In recrystallized doped PM rod, larger voids were observed and were identified by precision dark field analysis to be cubic in shape and bounded by (100) planes. In marked contrast with both the doped PM materials, recrystallized undoped PM rod exhibited only very occasional and randomly arranged voids. Furthermore, no voids were observed in either material after electron beam melting. The high concentration of voids in the doped PM materials is attributed primarily to vaporization of doping additions or their pvoducts situated at the original grain boundaries , whereas the few voids in undoped material are considered to be traces of microporosity which were not eliminated during sintering. A tentative mechanism is suggested for the dezlelopment of the voids in relation to the processing sequences (sintering and working) and to the subsequent annealing. In recent years, a characteristic substructural feature consisting of rows of small elongated or circular regions of light contrast lying along the direction of working has been seen in thin foil electron microscopy studies of annealed sheet, wire, and rod tungsten. These features were present in the published micrographs of sheet by Weissmann et al.1 and of wire by Meieran and Thomas2, although the authors did not draw attention to them. Wronski and Fourdeux3 observed similar features in sintered rod tungsten (it was not specified whether or not the material was doped*) and interpreted them on the basis of their ap- particles, based on extraction replica evidence from the fracture surface of the initial hot-rolled slab material from which the sheet was prepared. No diffraction contrast experiments on the features were reported in any of these studies. The present investigation was undertaken with the primary objectives of: a) identifying the nature of these substructural features in tungsten by electron diffraction contrast experiments, since the contrast for voids can be expected to differ from that for crystalline or glassy particles, and b) elucidating the origin of the features and their development. For the latter purpose, doped and undoped powder metallurgy tungsten was obtained as rod and wire to represent different stages of reduction during final processing. These materials were examined both in the as-processed condition and after annealing to successively higher temperatures. In addition, the same doped and undoped materials were examined after vacuum melting in rod form. I) MATERIALS AND PROCEDURE Doped powder metallurgy (PM) tungsten wire (commercial purity 99.9 pct W) was obtained in the as-drawn and surface ground condition (0.030 in. diam "ground seal rod"). Doped and undoped tungsten rod (0.075 in. diam) representing an earlier stage of final processing was obtained from the same commercial source (Refractory Metals Division, General Electric Co.). Lengths of both the doped and undoped rod materials were single-pass melted in an electron-beam zone refiner to examine the effect of vacuum melting on the substructure. Annealing was carried out in a tungsten crucible in a tantalum strip resistance furnace under a vacuum of l0-15 mm Hg. Longitudinal sections of the wire and rod materials were examined by light and electron microscopy. The preparation of thin foils suitable for electron transmission from 0.030 in. diam tungsten wire and the rod specimens was carried out by means of a high-precision microjet technique developed to provide lack of jet stability and precise control of the area thinned. The method is described in detail elsewhere.' The foils were examined in a JEM 6A electron microscope using a goniometer stage (±20 deg tilt, 360 deg rotation) and operated at 100 kV. To minimize contamination problems a 200 µ condenser aperture was used in conjunction with a useful beam current of 50 µA. II) RESULTS AND DISCUSSION A) Diffraction Contrast Analysis. In order to determine the optimum conditions for the development of the substructural feature, a series of isochronal 30 min annealing experiments were carried out on specimens of the doped PM tungsten wire. The transmission electron microscopy analysis showed that the as-drawn wire, Fig. 1(a), consists of 'fibers' whose long axis is closely parallel to the wire axis of (110). The fiber width averages some 0.5 µ. Dense disloca-

Jan 1, 1969

By Murl R., Schrock

THE use of diamond-drill holes at the Moctezuma Copper Co., Pilares mine, Pilares de Nacozari, Sonora, Mexico, for the ventilation of raises has resulted from experiments that were made in an effort to secure continuous and efficient ventilation in hot and gaseous raises. The method is particularly applicable in long raises and in raises run from development levels where the source of fresh air is distant. In order that the CO, concentration shall not become excessive, 30 cu. ft. per min. per man must be supplied to a heading for breathing purposes:' The quantity of air that will pass through a diamond-drill hole by

Jan 1, 1929

By William Klement

KNELLER' has recently reported that extensive metastable solid solutions may be obtained in Cu-Fe alloys by simultaneous vapor deposition. This note reports that solid solutions, apparently single -phase, can be obtained for Cu-Fe alloys containing 0 to 20 and 85 to 100 at. pct Fe by rapid quenching from the melt; the inability to extend the solid solubilities further is related to the liquid miscibility gap, Fig. 1, as for Cu-Co alloys.2'3 Accurate lattice spacings of the copper-rich fcc and iron-rich bcc solid solutions have been obtained. Homogeneous alloys were prepared by casting4'5 and sintering2 from elements of 99.9+ pct purity. The quenching techniques were as before,' except the iron-rich alloys were liberally covered with argon while at elevated temperatures. Flakes about 1 sq mm in area were obtained and investigated with the Debye-Scherrer technique, as previously described.2,4 All X-ray work was done at 25° 2°C using filtered copper and cobalt K radiation. Relative visual intensities of the diffraction lines for the phases in the quenched alloys are shown in Table I. The lattice spacings of the fcc structure for alloys containing up to 80 at. pct Fe are plotted in Fig. 2. The variation of these lattice parameters with composition is in good agreement with the re- of cementite spots usually present (all hkl reflections are allowed) and the ease of confusing them with ferrite or martensite reflections. Copies of the report can be obtained by writing to the Materials Research Department, Rocketdyne. 6633 Canoga Avenue, Canoga Park, Calif., 91304. A copy is also available at the Engineering Societies Library, 2nd floor, 345 East 47th Street, New York, N.Y., 10017. Photocopies, either full-size or microfilm, may be purchased from the Engineering Societies Library. sults6 of Andersen and Kingsbury, Fig. 2, although there is some disagreement in absolute value. This discrepancy may be due to the different temperatures at which the X-ray measurements were carried out and perhaps to the different extrapolation procedures. Also, Andersen and Kingsbury6 state that their lattice spacings were computed relative to the wavelengths given by Siegbahn in 1933; this reference has not been found and it is assumed that the well-known 1931 wavelengths were used, the lattice spacings then being in kx units which are converted into angstroms by the factor 1.00202. There is no support for the contention that solution of iron decreases the lattice parameter of copper, as con-

Jan 1, 1965

By R. E. Reed, R. D. Leggett, Paxton, H. W.

TECHNIQUES have been developed for growing monocrystals and bicrystals of Fe-20 Cr, Fe-20 Cr-20 Ni, and Fe-18 Cr-8 Ni alloys by both the strain-anneal and the Bridgeman techniques. None of the techniques are new but since they are simple and many people have expressed interest, they are described here quantitatively as they could be modified for other single-phase "commercial" materials of high melting point. CRYSTAL GROWTH BY STRAIN ANNEAL Flat tensile specimens with a tapered gage length were initially studied to deduce the approximate critical strain. Normal flat tensile specimens were then used. The optimum procedure for the austenitic steels (Fe-Cr-Ni) deduced from a variety of cold reductions, recrystallization treatments, tensile strain, and growth anneals was as follows: cold reduce 70 pct, recrystallize (after machining tensile specimens) at 1000°C for 1 hr, strain in tension 2.5 pct, and then heat to 1350°C as rapidly as possible. A time of 100 hr at 1350°C is usually sufficient to pro-

Jan 1, 1960

By Henry R. Piehler

Continuous seven- and nine teen -filament close-packed silver-steel filamentary composites mere tested in tension. For purposes of comparison, the tensile behavior of the composite was predicted from the measured properties of the individual com-ponents. It was assumed that the axial strain is the same in both components and that the contribution of each component to the composite flow stress is proportional to its volume fraction. Good agreetnent was obtained between the observed and predicted tensile behavior. However, the composite elongation at fracture was about twice that observed when the individual steel wires were tested alone. Composites in which the filaments were widely spaced failed by the consecutive fracture of the filaments. In composites with closely spaced filaments, a composite instability preceded frachcre. These effects are explained in terms of a lateral restraint to the necking of the filaments which develops in the deforming composite. TWO-COMPONENT or composite materials are increasingly being developed and used as structural materials. Of all the composite geometries used, the filamentary configuration has proved to be the most successful. Polymer-bonded fiber-glas, the most common of the filamentary composites, has been investigated most extensively to date. One explanation of the behavior of fiberglas1 suggests that the load transfer between the glass fibers and the polymer matrix occurs primarily through friction. Bond separation between the fibers and the matrix is presumed to occur at very low stresses. Subsequently, only frictional bonding can provide for the transfer of load from the matrix to the fibers. The force normal to the fiber-matrix interface which gives rise to this friction is assumed to arise from the matrix shrinkage which occurs during solidification. The behavior of metallic filamentary-composite materials would be expected to differ from that of fiberglas in several significant aspects. Residual stresses resulting from differences in thermal contraction can be kept to a minimum by proper heat treatment. A strong wetted bond is formed between the two phases. In brazed joints,2 for example, the interphase bond is sufficiently strong that the weaker material will fail before separation occurs at the interface. Most metal filaments can undergo appreciable amounts of plastic deformation before failure. Failure by plastic instability or necking frequently occurs in metallic filaments, but not in glass fibers tested at room temperature. Differences between the behavior of fiberglas-polymer and metallic filamentary composites have indeed been observed in composites containing various types of metallic filaments in a silver matrix.3,4 At strains of the order of 10-2 pct, all the deformation was accommodated by the silver matrix. Hence, the strength of the composite depended only on the fiber concentration and not on the nature of the fiber. At higher strains, the strength of the composite increased when filaments with higher work-hardening rates were used. Surface slip line observations on a silver-mild steel composite that had been stretched 4 pct showed that an appreciable amount of deformation occurred in the filaments. Work on tungsten-copper filamentary composites5 has shown that the ultimate tensile strength for varying filament fractions followed a linear mixture rule. Assuming that the axial strains in both filaments and the matrix are equal, this linear mixture rule can be expressed as: The subscripts c, f, and m refer to the composite, filaments, and matrix, respectively. A and V are the area and volume fractions of each component. sc and of are the ultimate tensile strengths of the composite and the filaments. sm is the flow stress of matrix at a strain equal to the elongation at failure of the filaments. However, the tungsten filaments can undergo only a limited elongation before they fracture without an appreciable reduction in area. A composite containing more ductile filaments might indeed deviate from this linear mixture rule for the ultimate tensile strength, since filament failure by necking might be arrested by the matrix. SPECIMEN PREPARATION Specimens were prepared from 0.8 pct carbon steel piano wires of 0.015 in. initial diameter. The wires were given a thin nickel flash and a silver plate varying in thickness from 0.015 to 0.007 in., depending on the filament fraction desired. In order

Jan 1, 1965

By Harold B. Goldman, Don Reining

The sand and gravel industry is the largest nonfuel mineral industry in the nation. In 1981, the production of sand and gravel totaled 755 million tons valued at $2.3 billion. California, which leads the nation with more than 110 million tons, together with Alaska, Texas, Michigan, and Ohio, account for 36% of the total production in the nation (Table 1). In commercial usage, sand applies to rock or mineral fragments ranging in size from particles retained on a No. 200 sieve (0.074 mm openings) to those passing a No. 4 sieve (4.76 mm openings). Gravel consists of rock or mineral fragments larger than 4.76 mm, ranging up to 88.9 mm (3 ½ -in.) maximum size. The construction industry consumes 97% of the sand and gravel produced; the remainder is sand used for specialized products such as glass (see the chapter on "Silica and Silicon"). Utilization The building industry uses sand and gravel chiefly as aggregate in portland cement concrete, mortar, and plaster; the paving industry uses sand and gravel in both asphaltic mixtures and portland cement concrete. Aggregate is commonly designated as the inert fragmental material which is bound into a conglomerate mass by a cementing material such as portland cement, asphalt, or gypsum plaster. Portland Cement Concrete Aggregates Portland cement concrete consists of sand and gravel surrounded and held together by hardened portland cement paste. Concrete mixes commonly contain 15-20% water, 7-14% cement, and 66-78% aggregate. Sand and gravel used as concrete aggregate have to meet many requirements (Goldman, 1956). Premature deterioration of concrete has been traced in many instances to the use of unsuitable aggregates. Asphaltic Aggregate Asphaltic mixtures used predominantly for paving consist of combinations of sand, gravel, and mineral filler (material finer than 0.003 in.), uniformly coated and mixed with asphalt produced in the refining of petroleum. Except for the addition of mineral filler, sand and gravel used as asphaltic aggregate must meet the same general physical requirements as materials used for portland cement concrete aggregate. General Requirements of Aggregates Construction aggregate has many requirements that are difficult to meet if only unprocessed material from natural deposits is used. Suitable material is composed of clean, uncoated, properly shaped particles which are sound and durable. Soundness and durability are terms used to denote the ability of aggre- [ ]

Jan 1, 1983

By H. C. Schultz

CERTAIN local conditions were known to govern in large measure the successful adaptation of liquid-oxygen explosives to the large-scale blasting at Chuquicamata. The wide variation in hardness of the rock at this mine makes necessary the use of several types of explosives. A locally manufactured, relatively cheap black powder is used in blasting the softer waste and capping material, where a thorough displacement breaks the ground sufficiently. Before the introduction of L. 0. X., an ammonia dynamite of about 65 per cent. strength was being used exclusively in the harder underlying orebody, where a strong disruptive as well as a displacement effect is required for breaking the ore. The L. 0. X., as developed for quarry work in the United States, has a practically pure carbon cartridge material, and the explosive has an extremely high rate of detonation, which should therefore cause it to usefully develop its full disruptive effect in hard ground. The individual blasts at Chuquicamata are large, black-powder shots which dislodge masses of rock averaging 250,000 tons each, and dynamite shots which dislodge masses averaging 80,000 tons each. It was desirable, therefore, to attempt to displace with L. 0. X. the faster, higher-cost ammonia dynamite used in the smaller blasts. It was not considered practical to attempt to displace the low-cost black powder with L. 0. X., as estimated costs showed no probable saving if this were accomplished. Since it was desirable to continue shooting relatively large blasts for effective operation, it was recognized that larger storage facilities than had been in use would be needed for the liquid oxygen. Because of the difficulty of transporting and discharging large storage containers of efficient design, the better plan appeared to be storage and discharge of the liquid at the place of manufacture, and transportation of the filled soaking boxes to the blast.

Jan 1, 1928

By L. Luini, E. Lee

An exploratory survey of the heat treatment response of commercial titanium alloys (Ti-150A, RC-130B, and MST 3AI-5Cr al-loys) shows a wide range of possible hardness and microstructural characteristics. The hardening is primarily dependent on the solid state transformation of the phase. An age hardening reaction which apparently is associated with ß decomposition and precipitation has been shown. Brittleness and notch sensitivity appear to be characteristic of age hardening to high hardness. Ductility, tensile strengths, and elongations are given. A NUMBER of commercially produced titanium-base alloys have been made available by the titanium metals industry. These alloys were developed to combine the light weight of titanium with increased strength through alloy additions. Usually the properties of these alloys are reported for material in the hot rolled and annealed condition. Since the production of commercial titanium has preceded the investigation of titanium-base alloy systems, the potential of these alloys is not well known. Although heat treatability has been indicated for these alloys, data on the response to heat treatment are quite limited. The heat treatability of titanium is based on the allotropic transformation of the high temperature, body-centered cubic ß structure to the low temperature, hexagonal close-packed a structure at approximately 1625 °F. This transformation in the pure metal is of little practical significance in heat treatment since the high temperature phase is not amenable to controlled transformation. Alloy additions serve to alter the transformation kinetics and permit control of the transformation by heat treatment variables. The effects of different alloys on the allotropic transformation in titanium classify them in two general categories,1 a stabilizing and ß stabilizing elements. The a stabilizers, represented by aluminum and oxygen, raise the temperature limits of the low temperature phase and introduce a two-phase a + ß temperature range. The ß stabilizers, represented by molybdenum and columbium, lower the equilibrium temperature of ß and give rise to an extended temperature range where both a and ß phases are stable. Another type of ß stabilizer, represented by iron, chromium, and manganese, introduces a eutectoid reaction. Some commercial titanium alloys belong to complex multiple element systems. Based upon the phase diagrams of the binary systems, the general effect of commercial compositions is to vary the stability of the high temperature phase and significantly alter its transformation characteristics. Therefore it is expected that the characteristics of alloyed titanium can be altered by heat treatment. The present investigation was undertaken to survey the variations in hardness, microstructure, and mechanical properties as affected by heat treatment variables. Commercial Alloys lnvestigated The commercially available titanium-base alloys selected for this investigation and obtained as 3/4 in. diameter hot rolled and annealed bars are listed in Table I. The producer did not determine the chemical composition of the Ti-150A heats X1052 and L685. The early heats of Ti-150A, prefixed with the letter X, were melted with tungsten-tipped electrodes and cast in approximately 500 lb ingots 12 in. in diameter. The heats prefixed with the letter L were melted under a revised melting practice yielding approximately 1300 lb ingots 16 in. in diameter. The final annealing treatment was at 1200" to 1250°F for 1 hr. The MST-3A1-5Cr alloy was melted in an induction furnace and cast in 7 in. diameter ingots. This practice produces high carbon material and some variation in the amount of carbides was found in different sections of the same bar. The RC-130B alloy was melted with a carbon arc. This alloy showed approximately 2 pct carbides. No large segregation effects were observed.

Jan 1, 1955

By W. O. Philbrook, R. H. Spitzer, F. S. Manning

A generalized mathematical model has been developed to describe the kinetics of the gaseous, topo-chemical reduction of porous hematite spheres. Gas-solid reduction is permitted at each of three advancing interfaces and is controlled by a complex series-parallel sequence of chemical and transport steps. Despite the fact that transport resistances are significant to the advance of each interface, little deviation from linear advance is predicted for the first 98 pct of reduction. Calculations to predict the movement of magnetite /wustite interface by a solid-state diffusion mechanism have been incorporated into the earlier dense-pellet model.' The porous-pellet model is found to give a better description than the dense-pellet one for McKewan's measurements2 of interface movements in dense polycrystalline hematite reduced in hydrogen-water vapor mixtures. THIS paper reports a continuation of work"3" directed toward the better understanding of gas-solid reactions and the development of mathematical models that may be helpful in the design or control of ore-reduction processes. Laboratory studies of the reduction of single oxide samples in tube furnaces normally employ an abundant excess of pure reducing gas. Reduction may appear to be adequately described by a model assuming gas-solid reaction solely at the iron/wustite interface.''' However, when iron ore is reduced in either a fixed bed or an efficiently operated counter-current column, there are portions of the bed where the partially spent gas is no longer capable of reducing wustite to iron. Nevertheless, the formation of the intermediate reaction products, wustite or magnetite, can and does continue. In order to account for this aspect of the reduction of beds of particles, three semiempirical mathematical models were devised.' One of these was for the limiting case of completely dense particles, and two alternatives were provided for porous particles. For purposes of the analysis, a dense pellet was defined as one in which the wustite and magnetite layers were impervious to the reducing gas when the atmosphere was capable of forming iron. In a porous pellet, the intermediate product layers were assumed to be sufficiently permeable to allow reducing gas to penetrate beyond the iron/wustite interface to form wustite and magnetite by removal of oxygen as a gaseous product rather than by a solid-state redfiction mechanism. Further progress required a better understanding of the reaction of the individual particles with the gas stream. A comprehensive mathematical treatment was developed' to describe the continually changing interplay of transport and reaction steps

Jan 1, 1967

By Edward Jeffrey

THE use of coke in metallurgy, to any important degree, dates from the middle of the 18th century. Its utilization came most opportunely for European civilization. The forests of Europe, except in the most remote and inaccessible regions, had been largely fed, in the form of charcoal, into the smelting furnaces. For a hundred years-the middle of the 17th to the middle of the 18th century-there was a stationary condition of population corresponding to the exhaustion of European forests. This situation, which was particularly evident in Great Britain, was due to the fact that the forests had been depleted and the practical utilization of coke had not begun. The coking industry is essential for our metallurgical industries, which in turn are basal to healthy economic progress. But coke is of great importance, not only on its own account, but for its byproducts, which enter fundamentally into all the arts of peace and war. The dyestuff industry and the manufacture of explosives are intimately connected with one another, as was shown by the recent war. The subject of coking coal, therefore, is well worthy the serious attention both of practical industry and the scientific investigator. The most valuable coking coals, from the metallurgical standpoint, are derived from the coals of highest ranks. Coals, for example, that have a carbon ratio of from 70 to 80 per cent. yield the most valuable coke for the blast furnace. The difficulty of investigating these coals, however, is great, for they are rather friable and delicate and possess a high carbon content, which makes them difficult to manipulate. They present, on account of their high carbon content, a considerable degree of opacity when examined, in thin sections, under the microscope. The tenderness of structure and blackness of such high-grade coking coals as those of Connellsville and the Pocahontas region make them extremely difficult to investigate.

Jan 1, 1925

By M. van Swaay, C. E. Birchenall

A. S. lBrling (Johnson, Matthey & Co. Ltd., Laboratories)— Because of its initial emphasis upon the production of membranes by powder metallurgy and by normal casting and rolling techniques, this paper is of considerable interest to those concerned with the design and application of industrial diffusion units. As the subsequent performances of the three grades of palladium were not compared in detail, it can perhaps be concluded that specific permeabilities were very similar. A short table in which the absolute diffusion rates obtained by the Authors with their three grades of palladium were compared with those of other investigators18-25 would, however, have been of particular value in view of the very variable results obtained with this membrane material. The Authors state early in the paper that the permeability of the thoriated samples decreased in much the same way as that of the nonthoriated samples. Later, they emphasize that sintered palladium without thoria was very susceptible to poisoning and did not respond as well as the other materials to the decontamination treatment. These results, which suggest that sintered membranes are less effective than those produced by normal methods, have considerable industrial implications, and amplified experimental details would be very welcome. The results of the Authors differ in one important respect from those of other investigators. Thus, no "bleeding" was required to maintain a constant rate of diffusion, although Davis, Darling, and De Rosset found this to be necessary. Davisz3 found that "bleeding" was necessary even when the hydrogen had already been purified by diffusion through a palladium tube, and it would be of value to know the purity of the gas stream emerging from the purification train shown on Fig. 1 of the Authors' paper. The Authors show that diffusion rates varied according to the square root of the pressure difference providing that the palladium membrane was not contaminated in any way. This finding is in agreement with the results of those workers2,18,19,23,24 who diffused their hydrogen through the membrane into a partly or completely evacuated system.Those workers who did not find this square-root law dependence did not have a partial vacuum on the downstream-side of the membrane.'' The difference between the two experimental con- ditions appears to be significant, as the absolute diffusion rates per sq cm of diffusion area are lower when the square-root law dependence is not observed. While the effect could be attributable to poisoning of the membrane it is conceivable that a positive pressure on the downstream side of the membrane might influence the mechanism of diffusion. In view of the capricious behavior of palladium, factors of this type, which are likely to influence its industrial significance, should be carefully considered. M. van Swaay and C. E. Birchenall (authors' 9-eply) — Our Eq. 191 may be compared with several others for hydrogen diffusion in palladium: D = 5.95 x exp (-5770/1)' D = 3.55 x 10"3 exp (-5550/)' D = 4.3 x 10"3 exp (-5620/1')' Other values are given in the literature, but in many cases surface poisoning may have affected the results. No analysis was performed on the hydrogen gas stream after purification. It should be noted that the presence of liquid nitrogen traps near the heated membranes may have set up convection currents and provided the equivalent of "bleeding." The question of whether a partial vacuum existed on the downstream side of the membrane is not clear. Does it imply that there is something unique about the permeability measured near one atmosphere pressure? We do not believe that there is. When square root pressure dependence is not observed, diffusion rates are not measured. Is "absolute diffusion rate per sq. cm. of diffusion area" equivalent to permeability? The terminology is new to us. In any case we doubt very much that pressures of the order of several atmospheres can affect the mechanism of diffusion.

Jan 1, 1962

By B. G. Reisdorf

This paper describes the microstructural changes that occur when quenched ultrahigh-strength steels containing OA pet C and various amounts of nickel, silicon, and cobalt are tempered. The changes that occur in hardness, yield strength, and martensite diffraction-peak widths when these steels are tempered are related to the precipitation of the carbide phases. An unea$ectedly high silicon content (about 30 pct) was found in the E -carbide phase in a steel containing only 1.5 pct Si. TEMPERED martensitic steels have such wide-spread utility that they have been the subject of numerous investigations, and a sizable amount of literature has developed on this subject.M This investigation, which is a part of a larger program to correlate microstructure with mechanical properties at a variety of strength levels, is limited to the microstructural changes that occur when a quenched 0.40 pct carbon steel (USS Airsteel X-200 steel) is tempered, and to the effects of the alloying elements—nickel, cobalt, and silicon—on these microstructures. Used in this investigation were electron microscopy, electron-diffraction identification of the carbide phases, electron-probe micro-analysis of the carbides, X-ray determinations of retained austenite, and measurements of martensite X-ray diffract ion-peak widths. MATERIALS AND METHODS The chemical analyses of the eight heats examined eats No. 30 through 37) are shown in Table L Heat No. 30 has the chemical com~osition of Airsteel X-200, and the remaining seven heats contain various amounts of nickel, chromium, cobalt, and silicon. The heats were air-melted in an induction furnace and cast into 8 by 8 in. ingots that were subsequently heated to 2300 and rolled to 1-in.-thick plate. Oversize 0.505-in.-diam tensile specimens were rough-machined from the plates and austenitized in air at 1700° F for half an hour and oil-quenched. The specimens were then tempered in air at temperatures of 400° to 1000 for tempering times of 1, 4, and 16 hr, and finish-machined to 0.505-in.-diam tensile specimens. Electron micrographs were prepared from Formvar replicas of the midthickness of tensile-specimen shanks that had been electrolytically polished and etched in nital. Electron-diffraction patterns were obtained from carbon-extraction replicas. The replicas were prepared by etching the sample surface in the same manner as for microscopy, evaporating carbon on the etched surface, and re-etching the sample to free the carbon film and the precipitate particles. Electron-probe microanalysis was performed on some of the extraction replicas. To obtain adequate fluorescent X-ray intensities, several thicknesses of replica were exposed to the electron beam so that the results represent an average composition of the extracted particles rather than an analysis of single precipitate particles. The retained austenite contents of the specimens were determined by an empirical X-ray diffraction

Jan 1, 1963

By Hans Lundberg

IN ORDER to comprehend the help and information that may be expected from electrical prospecting, it is necessary to have at least a general knowledge of the methods and principles involved in preparing and interpreting results obtained in the field. Electrical prospecting is rather complicated, both in theory and practice, and in order to make a brief description clear to the practical mining man it has been necessary to idealize and generalize the problems, at the risk of having such simplification criticized by the theoretical man. This simplification must not be misinterpreted as showing a lack of theoretical knowledge. FIG. 1.-FLOW OF CURRENT IN AND AROUND A CONDUCTING BODY. For its operation, electrical prospecting mainly depends on-the fact that most metallic ores conduct an electric current much more readily than barren rocks. If an electric current flows through a block of ground within which a body of chalcopyrite is enclosed in country rock of schist, the current will find less resistance to its passage through the chalcopyrite than through the schist, even though the passage through the latter be much shorter. This is because the longer path through the chalcopyrite offers less resistance, owing to the superior electrical conductivity of the chalcopyrite (Fig. 1).

Jan 1, 1928