Search Documents

By Richard O. Kneisley

An empirical method, based on U. S. Bureau of Mines field studies in several Western U.S. coal mines, is presented for sizing gate road yield pillars. Discriminant analysis was used to generate functions separating successful from unsuccessful case studies. These functions relate the pillar width-height and extraction ratios and a pillar development factor to the Coal Mine Roof Rating System (CMRR), and are assumed to establish three criteria that other entry systems, under similar conditions, must satisfy. A program, Pillar Sizer, from user-provided inputs, generates a range of pillar sizes that meets the proposed criteria. Although the analysis is based on a sample consisting primarily of two-entry systems, the derived expressions generate pillar sizes closely agreeing with observed, two-entry and three-entry in situ pillars. It is concluded that the proposed approach should assist mine operators estimate entry system yield pillar dimensions.

Jan 1, 2010

By E. D. Eastman

"The factors that determine the efficiency of reduction of iron oxides by gaseous reducing agents may be considered in two classes; those which effect the equilibrium between the reacting substances end their products, and those which affect the rete of reaction. Both sets are of prectical importance, the former as influencing the maximum possible efficiency and the latter as determining what fraction of the maximum yield may be readily or profitably obtained. In addition, the thermal changes attending the reduction greatly affect the chance of successful industrial application of any such process, and knowledge of them is necessary for the intelligent design of apparatus and control of the reaction. Some aspects of each of these three divisions of the problem are discussed below.I. The Maximum Reducing Power of Fuel Gases on the Oxides of IronsThe gases that heve been considered specifically in this work are coal gas, water gas and producer gas, typical analyses” of which are given in Table 1 Of the various hydrocarbons represented in Table 1, (several being grouped or averaged as C2R4), methane is the only gas assumed to be capable of existence at appreciable pressures under the conditions of interest here. The equilibria in the several systems which may ensue when one of the above gases is allowed to react with the iron oxides, may therefore be represented in the most general case by equations of the type of the following arbitrarily chosen ones:"

Jun 1, 1923

By Joe B. Rosenbaum

New applications and concepts of solvent extraction as a unit operation in extractive metallurgy have been developed in the last decade. Wider use is being made of established solvent extraction techniques in processing spent nuclear fuel elements and in winning columbium-tantalum, hafnium-zirconium, thorium, tungsten, uranium, and vanadium. Commercial application has been extended to recovery of beryllium, boron, bromine, copper, molybdenum, phosphorus, rare-earth metals, and rhenium. Systems in use and proposed typically extract metals or salts as anion, cation, or neutral species from aqueous media by reaction with a recycleable organic reagent.

Jan 1, 1971

By C. J. Mains

The gas -flow oil-shale retort is a continuous, crass flow, gas -to -broken solid heat-exchange system in which heat is transferred by convection from the gas to the solide.2/ This type of heat transfer presents a problem of analysis that cannot be solved by methods in common use. Solution of this problem is necessary for design, operation analysis, and predict ion wherever that type of heat exchanger is used. This report embodies a method for calculation of heat transfer coefficient and temperature histories of gas and solid in the gas- flow retort operating at equilibrium conditions. Detailed calculations are presented to show the application of the method explained in this report to conditions of an actual run made in the gas-flow retort. Although used here for a specific case, the method is applicable to all heat exchangers that are characterized by continuous, crossflow, gas -to-broken solid heat transfer. INTRODUCTION In any direct, gas -to -broken solid heat -transfer system, it is difficult to measure the temperatures of the gas and solid inside the heat exchanger. The driving force for heat transfer between the two media in the bed there- fore usually is unknown. The major resistance to heat transfer is in the gas film surrounding the solid particles, and the thickness of this gas film is neither uniform nor can it be determined readily. It is well to point out also that determination of the surface area of the particles is of poor accuracy. Since the driving force, the major resistance, and the surface area in the heat-transfer system are such uncertain quantities, It is not feasible to calculate the heat transfer by usual methods. All of the fore- going statements are true of the gas-flow retort; as a result, efforts were made to determine apparent heat-transfer coefficients and temperature histories of gas and solid in the heat -exchange bed by calculation using those data that were available. The heat -transfer coefficient calculated has the following dimensions: B .t .u. per second, °F., cubic foot of bed volume, where heat - transfer coefficients normally have the units; B .t .u . per hour, square foot, °F. Only the Schumann-Furnas formulas may be used to determine the heat- transfer coefficient and temperature histories in this type of heat exchanger.

Jan 1, 1953

By R. A. Cortese

The U.S. Bureau of Mines has developed a flame-radiation-powered trigger device to explosively activate suppression barriers to quench gas and coal dust explosions. The major component of the device is a silicon solar panel, which converts radiation from the developing explosion into electrical energy to initiate an electric detonator, which releases an extinguishing agent into the advancing flame front. Solar panels that are rated to produce 20 W of electrical power when exposed to the sunlight are producing about 200 W when exposed to a full-scale dust explosion. The solar panel is electrically isolated from the detonator by a pressure-sensitive switch until the arrival of the precursor pressure pulse, which always precedes a deflagration. This combination of pressure arming and flame-powered photogenerator prevents false barrier activation and requires no external power supply.

Jan 1, 2010

By J. P. McGee

A 1,000-hour test with a gas turbine at 1,200° F showed a working fluid of 1 gr of ash per 100 scf of power gas (79 percent of the ash 7 to 35 microns in diameter) to be excessive for acceptable blade wear for commercial practicability. Blades in the turbine consisted of about 20 percent each of chromium, cobalt, and nickel; 3 percent molybdenum; 2-1/2 percent tungsten; and smaller amounts of manganese, columbium, and tantalum. Erosion of both the fronts and backs of the turbine nozzles was particularly heavy, the trailing edges being worn to a featheredge. Erosion of the buckets was less marked, although the leading edges were somewhat pitted. A refractory-lined combustor performed efficiently and with little abrasion of the lining by the ash-laden gas.

Jan 1, 1969

By R. Van A. Mills

Crude oils are capable of dissolving quantities of gas under pressure. This fact has been known for some time, but questions have arisen as to the effects of gas in solution upon the characteristics of the oil. Previous investigations4 show that gas in solution in an oil affects the viscosity and surface tension of the oil, but the effect's on the volume and A. P. I. gravity of the oil have not been known. The results given in this report show that there is a decided change both in volume and in the A. P. I. gravity of the oil due to the solution of the gas in the oil under pressure. As gas is dissolved, the volume of the oil and the A. P. I. gravity increase. The converse of this phenomenon is also true: if the gas is released from a saturated oil, there is a shrinkage in volume and a decrease in A.P.I. gravity due to the release of gas from solution. However, various oils show marked tendencies to retain a portion of the dissolved gas upon releasing the pressure to that of the atmosphere. This retained gas has an appreciable effect on the volume and A. P. I. gravity of the oil because the oil does not resume its initial volume or gravity while it retains dissolved gas. In a sense the oil has been "Freshened" and will not return to its original or weathered volume until it loses some of the lighter fractions. Wiggins5 has shown that a fresh oil decreases both in volume and in gravity because of the weathering of the lighter fractions while the oil is standing in storage tanks.

Jan 1, 1928

By C. F. Ellis

Interest in the composition of automobile exhaust gases has been greatly accelerated by recent studies that have indicated that these gases contribute to smog formation in urban areas. Several analytical methods have been published for the analysis of the hydrocarbons in the exhaust gases, but similar information has not been published on the analysis of the oxygenated compounds. This report presents procedures for chemical analyses of certain oxygenated compounds, procedures for sampling the exhaust gases for these analyses, and the analytical results of some experimental work in which these procedures were used. A stationary 1956 model, 170 horsepower, V-8, dynamometer-mounted engine, operated to simulate vehicular cruise conditions, was used for the study. Exhaust gases produced from a regular-grade Midcontinent gasoline during 15-40- , and 60-mile-per-hour cruise operations were analyzed by chemical methods for formaldehyde, total aldehydes, total carbonyls, total alcohols, carbon associated with the oxygenated compounds, and the oxides of nitrogen. Experimental results indicate: 1. The range of concentrations of the total of the functional groups of oxygenated compounds, expressed as moles per million moles of water-free exhaust gases, is about 90-100; the concentrations increase with engine speed. 2. Aldehydes comprise about 80-90 mole- percent of the total of the oxygenated groups, and formaldehyde accounts for about 50 mole-percent of the total aldehydes. 3. The order of magnitude of the concentration of the carbonyls is the same as that for the aldehydes, indicating that ketones are not a major group. A colorimetric test indicates that methyl ketones Constitute about 2 mole-percent of the oxygenated compounds.

Jan 1, 1961

By John C. Gagliardi

The size and complexity of modern surface haulage trucks has resulted in an increased reliance upon sensors and electronic-based instrumentation for safe and efficient operation. Design engineers need accurate information about the equipment vibration environment to efficiently and effectively build components for installation on mobile mining equipment capable of withstanding the mine environment. Examples of such components include backup alarms, communication equipment, microprocessor-based controllers, and a wide variety of sensors. Unfortunately, this information is not available to the majority of both original equipment and aftermarket equipment manufacturers. To address this problem, the U.S. Bureau of Mines performed field vibration measurements on a variety of surface mining haulage trucks. The vibration measurements were then analyzed and test specifications were developed in the form of envelopes. In conjunction with test specifications, recommendations to aid manufacturers in implementing a vibration environment test program have been included with an illustrative example.

Jan 1, 2010

By Stephen Gerard Sawyer

A Fortran IV computer program entitled WAVE, which employs an explicit finite difference scheme for solving the one-dimensional wave equation for a time-dependent inelastic rock has been developed. The viscoelastic properties of the rock are represented in terms of a generalized Voigt model. The theory on which the computer program is based is rederived and a short description of the program is given. The computer program input instructions, a listing of the computer program, and example problems with required input and subsequent printed output are presented in appendixes. In the example problems) calculated results are free of spurious oscillations which occur in certain other methods of numerical calculation) notably the extended Ritz method.

Jan 1, 1972

By Alla D. Mah

The energies of combustion of two carbides of tungsten and two carbides of molybdenum were measured , and the corresponding standard heats of combustion were derived . The results are as follows : WC : AH298.15 ( combustion ) = -285,940 ± 250 cal /mole , W₂ C: AH298.15 (combustion ) = -490,660 ± 400 cal /mole , Mo₂ C : AH298.15 ( combustion) = -439,350 ± 600 cal /mole , MoC : AH298.15 ( combustion ) = -269,800 ± 1,000 cal /mole . The combustion heats were combined with the heats of formation of the corresponding metal trioxides and carbon dioxide to obtain the following heats of formation : WC : AH298.15 ( formation ) = -9.6 ± 0.4 kcal /mole , WC: AH298.15 ( formation ) = -6.3 ± 0.6 kcal /mole , Mo₂ C : AH298.15 (formation) = -11.0 ± 0.7 kcal / mole , MoC : AH298.15 (formation ) = -2.4 ± 1.0 kcal /mole . The heats of combustion and formation of MoC are tentative .

Jan 1, 1963

By J. C. Meeks, C. L. Klingman

An instrument that is sensitive , portable , safe , and low in cost was developed by the Bureau of Mines for detecting helium leaks by comparing the thermal conductivity and flow rate of the atmosphere around the suspected leak against a reference of helium- free air . A vacuum pump pulls the sample gas through a restriction and over thermistor elements , the combined electrical output of which is affected by thermal conductivity and flow rate of the sample gas . Tests showed that the battery - operated Helium Leak Detector was effective and rugged instrument that could be operated safely in explosive atmospheres . The instrument could also detect , but not identify , other gases such as methane , hydrogen , argon , carbon dioxide , and Freon 12 .

Jan 1, 1964

By W. P. Yant

The widespread use of toluene in industry and the importance of air analysis in industrial-hygiene surveys have created a need for a simple and accurate method for determining toluene vapor in air. Most of the methods used to determine small quantities of toluene in liquid or vapor form are based on the measurement of its physical properties. Methods based on fractional distillation, determination of specific gravity, use of the interferometer, use of the spectrograph, and sorption on solid sorbents with subsequent determination of gain in weight have been employed. Distillation and specific-gravity methods are not applicable to the small quantities of toluene found in the air, and use of the interferometer, spectrograph, and sorption methods either are not specific for toluene in the presence of other volatile substances or require expensive equipment.

Jan 1, 1936

By Ernest A. Curth

The Bureau of Mines studied pressure changes in coal pillars by using encapsulated hydraulic pressure cells to measure relative changes in stress developed during mining. The data indicate that (1) abutment stresses were detected when the pillar line is within 42 to 100 feet, (2) vertical pressure increases as coal is mined in the pillars, (3) at first pressure is higher at the edge of the pillar than in the core, but as mining progresses, the higher pressure is measured in the core of the stump, and (4) in the two instances where lateral pressures were measured, they remained lower than the vertical pressures during pillar extraction. The data also indicate that the mean vertical pressure increase, 6P, in a pillar is roughly related to the percent of pillar extracted, A, by the empirical parabolic equation

Jan 1, 1967

By Daryl R. Tweeton

The Bureau of Mines compared the effects of surface-active chemicals with those of pure water on core-drilling rock and quartz and on fracturing quartz. The objectives were to determine if these chemicals assist drilling and fracturing rock and if zeta potential control was worth pursuing as an aid to full-scale drilling. All tests were performed in the laboratory. No significant increases in drilling rates were observed for 1 to 10,000 ppm Al (as AlC13) in flushing water when drilling microcline or serpentine, nor for 1 to 10,000 ppm Mg (as MgC12) when drilling microcline or marble. Concentrations near those giving a zero zeta potential were used with microcline and marble. A 50-pct rate increase was observed for drilling quartz in 0.7 ppm oleylammonium acetate, which gave a zero zeta potential. No other concentrations were used. No effect on the tensile strength of quartz thread in 0.05 ppm Al (as AlC13), which gave a zero zeta potential, was observed. Heptanol, reported to give a zero zeta potential on quartz, did not reduce the bending strength of small quartz bars below that in water. These generally negative findings raise doubt about the usefulness of zeta potential control in full-scale drilling. The results, combined with previous studies, suggest that controlling physical properties of drilling fluids, such as viscosity, is more useful than altering chemical properties.

Jan 1, 1976

By Bernard Porter

The solubility of UO2 was determined at 1,250° C. in ternary melts of UF4 and BaF2 with CaF2, LiF, and SrF2. The solubility of Ce02 was measured at 800° and 850° C. in a solution of CeF3, BaF2, and LiF. The amount of La203 which dissolves at 950° C. in a binary mixture of LiF and LaF3 and a ternary of LiF, LaF3, and BaF2 was also measured. In each case, the amount of soluble oxide was mound to be less than 5 weight-percent. A procedure was developed for filtering fused, oxide-saturated fluoride melts in order to obtain a representative sample for chemical analysis. The oxide content of the samples was determined by an inert-gas fusion procedure.

Jan 1, 1961

By W. P. Yant

The widespread use of toluene in industry and the importance of air analysis in industrial-hygiene surveys have created a need for a simple and accurate method for determining toluene vapor in air. Most of the methods used to determine small quantities of toluene in liquid or vapor form are based on the measurement of its physical properties. Methods based on fractional distillation, determination of specific gravity, use of the interferometer, use of the spectrograph, and sorption on solid sorbents with subsequent determination of gain in weight have been employed. Distillation and specific-gravity methods are not applicable to the small quantities of toluene found in the air, and use of the interferometer, spectrograph, and sorption methods either are not specific for toluene in the presence of other volatile substances or require expensive equipment.

Jan 1, 1936

By A. C. Johnson

This paper is one of a series being prepared by the Bureau of Mines on exploration, development, mining methods and costs at various mines in the United States. It describes such methods at the Lincoln tungsten mine of the Wah Chang Mining Corp., Lincoln County, Nev. The purpose of these reports is to promote development and conservation of our mineral resources by disseminating technologic information on mining methods, practices and costs. The Lincoln mine in Lincoln County, Nev., in the southeastern part of the [tate], was acquired by the Wah Chang Mining Corp., in April 1951. Mining methods and costs are of special interest at this property because of the low costs and good production record achieved through a well planned program of exploration, development, and exploitation. Operations were discontinued in July 1957 after the Federal Government suspended the tungsten purchase program.

Jan 1, 1959

By John C. Franklin

Water-based epoxy sealants were examined during a 2-year period to deter-mine their effectiveness as barriers to radon release in uranium mines. Radon emanation rates from uranium ore samples were monitored for extended periods in the laboratory before and after sealant application. Reduction of radon flux due to the coating of laboratory samples was approximately 80 percent. Test chambers in a dormant uranium mine were monitored to determine both short and long-term barrier effectiveness. These field studies of the seal-ants indicated radon flux reductions exceeding 50 percent relatively soon after application and nearly 75 percent about 1 year later. An unexpected complication to early monitoring in the form of a large radon emanation increase, believed due to added moisture, is discussed.

Jan 1, 1977

By Kenneth M. Smith

The kaolin deposits of Aiken County, South Carolina (fig. 1), have been worked continuously since 1852. It has been long known that the deposits contain a high percentage of' alumina and that large reserves exist. These facts led to the early selection of' this area for examination in the search by the Bureau of Mines for high-alumina clays. An exploratory program was started by the Bureau, and drilling was carried on from. June 27, 1942, to October 31, 1942. The kaolin-bearing district occupies an area approximately 25 miles long and 11 miles wide, running northeast, with its center at Aiken, S. C. (fig. 1). Within this district, a triangular area bounded by Horse Creek, Silver Bluff Road, and Hamburg Road was roughly prospected by boring 43 machine and 12 hand holes. As a result of the data obtained, a final smaller area was chosen for more systematic prospecting. This area is bounded by Pine Log, Tewkesbury, Silver Bluff, and Craig Sawmill Roads and covers about 4,000 acres. Mineral exploration agreements covering 11,272 acres were signed by 35 property owners, and 11,956 feet was drilled in 200 holes on these properties.

Jan 1, 1949