Search Documents

By Van E. Shaw

Three comparatively simple, efficient, and rapid extraction methods for the dissolution of yttrium and rare-earth elements from a euxenite carbonate residue have been developed, using dilute sulfuric acid as the solvent. Extraction processes have resulted in yields of 98+ percent of the total rare-earth elements and yttrium contained in the residue and have given preliminary separation between the cerium-group and the yttrium-group rare-earth elements. Extraction procedures presented are: Procedure 1. -The recovery of total rare-earth elements and yttrium by a cold dilute sulfuric acid leach at a pH of 2.5. Procedure 2. -The recovery of yttrium and yttrium-group rare-earth elements by leaching with dilute sulfuric acid at 125° F. and a pH of 3.0, with subsequent recovery of the cerium-group rare-earth elements by a cold dilute sulfuric acid leach of the residue at a pH of 2.5. Procedure 3. -The recovery of the total rare-earth elements and yttrium by fractional leaching as in procedure 1, followed by boiling the sulfate solution, which precipitates the cerium-group rare-earth elements and leaves the yttrium-group rare-earth elements in solution.

Jan 1, 1959

By J. W. Jensen

Alloys of manganese and copper containing from 65 to 80 percent manganese possess mechanical strength and vibration-damping capacity in an unusually high degree. The success of their use in reducing vibration in structures depends, to some extent, on their fatigue properties. This report describes the results of fatigue tests on alloys of four compositions. Three metallurgical conditions were investigated for each alloy. Or the basis of the data in this report, the general rule that vibration-damping manganese-copper alloys are comparable to mild steel in hardness and strength may be extended to include fatigue strength. Methods for casting and fabricating these alloys were described in a previous report,4 which contained data on the mechanical and damping properties of the solid-solution alloys, and on alloys aged for 2 hours at 450° C. The aging heat treatment of solution-treated alloys results in optimum mechanical and damping properties throughout the range of specified composition. However, in the present work, measurements also were made on alloys aged for 2 hours at 500° C., because it was theorized that the additional precipitation of a-manganese under these conditions might have a pronounced effect on the fatigue strength of the alloy.

Jan 1, 1961

By F. M. Goodwin, Campbell. John, W. J. Hiffs, G. W. Jones

"INTRODUCTION In cooperation with The Edison Electric Illuminating Co. of Boston, Mass., and the Boston Consolidated Gas Co. a survey has been conducted continuously since 1929 by the United States Bureau of Mines to determine the general hazards of combustible gases and vapors in manholes of the Edison Electric Illuminating Co. The New England Telephone & Telegraph Co. also has cooperated in the investigation, and tests have been made in its manholes since May 1, 1933.Yearly reports 6 giving the results obtained since the start of the survey have been published.The method and procedure of conductin, the survey in 1935 were the same as heretofore.ACKNOWLEDGMENTSThe cooperative investigation was arranged through the interest and effort of F. D. Comerford, president of the Edison Electric Illuminating Co. of Boston; E. N. Farnesworth, Jr., vice president and general manager of the Boston Consolidated Gas Co.; and A. C. Fieldner chief engineer, Experiment Stations Division, U. S. Bureau of Mines. Thomas H. Haines, superintendent, Distribution Department, of the Edison Electric Illuminating Co., cooperated in furnishing men and information for the work,"

Oct 1, 1936

By A. E. Isaacson

Bureau of Mines researchers developed and tested equipment to measure corrosion rates on a commercial scale mill. Bench-scale experiments were designed for duplicating ore grinding conditions closely enough so that realistic rate determinations could be made in laboratory tests. Rates measured in a laboratory system compared favorably with those measured in the field. Cast steel was found to have corrosion rates in a copper mill and laboratory test cell of 22 and 21 mpy, respectively. Corrosion was found to account for less than 5 pct of the total grinding media wear in the operations studied.

Jan 1, 1988

By D. A. Stanley

The Bureau of Mines has developed a simple titration technique for determining the points of zero charge (PZC) on minerals. The technique consists of titrating a mineral slurry with the potassium salt of polyvinyl sulfuric acid (PVSK) in the presence of an indicatory dye and a positively charged polymer. Values obtained by this simple method are in good agreement with values found in the literature.

Jan 1, 1982

By D. E. Andrus

This paper, which describes the milling practice at the Montana mine concentrator of the Eagle-Picher Lead Co., is one of a series being prepared by the United Slates Bureau of Mines. LOCATION The Montana mine is situated on the eastern edge of the Oro Blanco mountains at an elevation of 4,300 feet. It is in the Oro Blanco mining district, Santa Cruz County, in the southern part of Arizona, about 4 miles north of the Mexican border, 30 miles northwest of Nogales and 80 miles southwest of Tucson. Amado, a station on the Southern Pacific Railroad, midway between Tucson and Nogales, and about 40 miles northeast of the mine, is the shipping point and is reached over an excellent highway.

Jan 1, 1931

By D. A. Rice

As part of its mission, the U.S. Bureau of Mines continues to develop technologies that will enable cost-effective compliance with environmental requirements. To this end, investigations to improve the kinetics of chalcopyrite dissolution by simultaneous grinding-leaching in ferric sulfate solution were conducted using the Bureau-designed turbo mill. The development of such a hydrometallurgical process would provide a nonpolluting alternative to conventional smelter technology. The effects of mill rotational speed and volume percent solids on the leaching time and energy required for copper extraction from chalcopyrite were evaluated. The results of this laboratory study have shown that the simultaneous grinding-leaching of chalcopyrite concentrate using the turbomill is technically feasible with essentially 100 pet extraction of copper being possible at 90° C. An optimal energy consumption of 1,153 kW?h/st of copper leached was found in batch testing with the mill operating at 400 rpm with a slurry containing 35 vol pet chalcopyrite. This energy consumption, while higher than other proposed leaching processes (about 600 kW?h/st), is of the same order of magnitude. Further refinement of the energy requirements would require additional testing using a continuous circuit. Leaching times of less than 1 h, for 80 pct copper extraction, are achievable using the turbomill grind-leach process.

Jan 1, 2010

By K. K. Kelley, W. W. Weller

Heat capacity measurements of lead molybdate and lead tungstate were conducted over the temperature range from 51 ° to 298 ° K. The entropies were found to be S298.15 = 39.7 ± 0.5 cal / deg mole for lead molybdate and S298.15 = 40.2 ± 0.5 cal / deg mole for lead tungstate . The entropy values were combined with other pertinent data to obtain the entropies of formation of the two compounds from their constituent elements and oxides .

Jan 1, 1964

By David M. Gullikson

Since publication of the paper on the composition of California oilfield waters by Jensen (6)3/ in 1934 the only other information on the subject was published recently by Chave (4). To supply needed information on the composition of California waters in areas of current drilling activity, the Federal Bureau of Mines collected formation water samples for analysis. Thirty-eight samples from oil-and gas-producing formations in 12 fields located in Ventura, Kern, Glenn, and Colusa counties were analysed by the Bureau's San Francisco Petroleum Research Laboratory. The samples were selected particularly from fields where the water composition was not well known or where interpretation of electrical logs has been difficult and the interpretation may be affected by unusual composition of the water. These samples were obtained from rocks ranging in geologic age from Cretaceous to Upper Pliocene. Fifteen constituents of these waters were determined including sodium, potassium, calcium, magnesium, strontium, barium, lithium, chloride, iodide, bromide, carbonate, bicarbonate, sulfate, borate, and residual acidity. These analyses are the first to be published on California oilfield waters in which determinations for potassium, strontium, bromide, iodide, boron) and naphthenates were made on a significant number of samples. The electrical resistivities of tae samples were determined at 75° F. and 175° F.

Jan 1, 1961

By Karl-Heinz Frohne

This report presents the findings of a study of a portion of the Clover-Rush Run oilfield located in Roane County, W. Va. The study was made to investigate the possibilities of secondary oil recovery in the Big Injun sandstone underlying the William Kaufman lease. Reservoir properties, original reserves, and primary oil recovery are also presented. The investigation is based on a core analysis and related laboratory tests, well records, field production data, and subsurface information from the Kaufman property. A theoretical primary oil recovery of 9.7 percent of original oil in place is predicted for the reservoir. A waterflood performance prediction of a hypothetical pilot area was made by use of a computer. The prediction showed that, based on laboratory oil water relative permeability curves, the water-injection time needed to initiate oil production is excessive and that the stabilized water-injection and corresponding oil-production rates are very low. This precludes waterflooding the reservoir on an economic basis. A prediction for secondary oil recovery by gas injection was attempted but could not be completed because essential reservoir data were not available. In July 1965, the lease operator initiated, and is currently conducting, a gas-injection program, but there had been no increase in oil production up to November 1966.

Jan 1, 1967

By Erich K. Bender

This report summarizes work performed under Phase I of USBM Contract No. H0366024, Noise Reduction of Jumbo Mounted Percussive Drills. Four drills -Gardner-Denver D93LAR and DH123 and Ingersoll-Rand 0475 and VL120 models were measured at the two manufacturers? test sites; data are given in terms of characteristic noise and vibration levels. A survey of percussive rock drill users is reported. The rationale for the choice of a demonstration drill, the Gardner-Denver DH123, is given and a desired noise reduction goal is established.

Jan 1, 1976

By James R. Boyle

The mining methods and practices used at the Young zinc mine, American Zinc Co. of Tennessee, have resulted in a low-cost, high-yield operation. Zinc ore (sphalerite) occurs in limestone-dolomite beds of the Kingsport Formation and is mined by modified room and pillar method. Utilizing trackless mining equipment which incorporates a high degree of flexibility, this operation has had a steady increase in productivity.

Jan 1, 1965

By L. P. Kleinmann

To control the formation of acid drainage at its source, the Bureau of Mines has investigated the role of iron-oxidizing bacteria in the oxidation of pyrite. In laboratory tests, it was determined that Thio-bacillus ferrooxidans could be controlled in coal refuse using anionic surfactants, with an associated decrease in acid production of about 75 pet. Based on these results, large-scale tests were conducted at an 8-acre active coal refuse area in northern West Virginia and an 11-acre inactive refuse pile in southern West Virginia. Acid production was decreased 60 to 95 pet for 4 to 5 months after application of 55 gal/ acre of 30-pct sodium lauryl sulfate solution. To date, effluent surfactant concentrations have been extremely low. Either a hydroseeder or a road-watering truck can be used to apply the surfactant. Since the surfactant solution must reach the pyritic material to be effective, sites that have been reclaimed are generally not amenable to these procedures. A simple laboratory test is described that provides an estimate of adsorption potential; this can be used to calculate a safe application rate.

Jan 1, 1983

By Will H. Coghill

This paper on milling methods and costs at a flat river (Mo.), mill is one of a series of information circulars on milling methods and costs which is being prepared by the United States Bureau of Mines, The mill under consideration treats 5,000 tons of load ore daily by table concentration and flotation. It is 25 years old, and yet it is a new mill. Research has been in continual progress at the plant since its beginning, and accordingly a day never passes without a record of change for advancement. The changes have been so orderly that no evidence of obsolete equipment remains.

Jan 1, 1932

By J. E. Schiller

The Bureau of Mines has investigated the surface charge of amphibole asbestos fibers and nonasbestiform cleavage fragments, as part of the Bureau's fundamental studies to provide new knowledge on the physical and chemical properties of the amphibole minerals. Microelectrophoresis was used to measure the electrophoretic mobilities, in water, of particles from six asbesti-from amphiboles and seven nonasbestiform amphiboles over the pH range of 5 through 9. The particles generally ranged in size from 2 to 5 µm wide by 10 to 30 µm long. The isoelectric point was determined for four of the minerals, and values were found to be between pH 3.5 and pH 5. The minerals studied had zeta potentials that generally ranged from -25 to -so mv in neutral solution. Attachment of colloidal positively charged AgI was also studied as a means of determining surface charge. Scanning electron microscopy of amphibole particles that had been in contact with aqueous AgI showed equal attachment of AgI to asbestos fibers and to cleavage fragments; the extent of AgI coating was the same for both. The electrophoretic mobilities of asbestos fibers were essentially the same as those of elongated cleavage fragments of the same aspect ratio (particle length divided by width). Blocky particles from both asbestiform and nonasbestiform specimens had lower mobilities.

Jan 1, 1980

By Walter E. Lewis

A mothod of cutting St. Poter sandstono by streams of water under pressuro from nozzles and pumping the resulting, sand to the surface has roduced the cost of storm-sowor construction in the Minneapolis-St. Paul aroa. The hydraulic tunneling method, has boon in uso since 1934, and it is adaptable only to the lower part of tho St. Potor, sandstone, which lios within or just abovo the ground-wator levol. Tho upper part of the formation, immediately bolow tho Plattoville limestone, 18 comonted and camot bo mined by hydraulic mothods. The tunnel oporation observed in this instance is a main storm sowor starting at tho Mississippi Rivor below the 10th Avenuo SE bridge and will be drivon 6,000 foot at a grado of 1 foot por thousand undor the city of Minneapolis to Konnody and Arthur Stroots NE. A lateral storm sowor, which branchos from the main sovor at 8th Street SE, will oxtond from 10th Avonuo SE to 15th Avonuc SE. Tho tunnele are being drivon with the floor approximately at ground-wator lovol. All waters ontoring the main storm sower vill drain into the Mississippi Rivor. Tho main storm sewer cross soction is excavated to a roughly hox- agonal shapo 10 foot high by 10 foot wido at the contor. The upper half of the tunnol soction is solidly lined with either timber or stool. After all oxcavation is completed, the tunnel will be finished with a concrete circular lining 8 feet in inside diameter. The lateral storm sewer is excavated to a 5-1/2-foot by 7-1/2-foot section and will event- ually be finished with concrete to a modified horseshoe-shaped section 6 feet by 4 feet. Where the back or walls are considered unsafe during excavation, the upper half of the tunnel is lined solidly with timber. The equipment used by the Sower Division, City of Minneapolis, has been selected to meet a number of applications in storm-sewer work with diversified usage in mind. The sand pumps used on this job are rubber-lined, designed to work against a head of 100 foet. Either 4-inch or 6-inch diameter suction and discharge openings may be used. Other equipment, such as pipe, mine rail, flexible hoses, compressors, and general surface shop equipment, is drawn from a contral warohouse. It may be either new or used, depending on what is available at the warehouse. Much of the pipe and mine rail has been used for many years on several different tunnol jobs.

Jul 1, 1950

By Larry D. Nichols

Poroplastic membranes containing ion exchange liquids were studied for separating cobalt from nickel-containing solutions similar to ammoniacal laterite leaches. The driving force for cobalt transport was differences in pH and composition between the leach and extraction streams. Using a diketone ion exchange liquid, a leach pH of 6.5 to 7.0, and a strip pH of 2.3, cobalt was extracted from a 750 ppm solution containing 2500 ppm of nickel at rates ranging from 1 to 10 µg/cm2 .min in single membrane cells, and from 10 to 100 in more closely spaced multiple membrane cells. Rates were variable, with evidence that cross -membrane flow pasterns were a key factor; a reproducible rate of 30 pg/cm .min would be economically viable. Loss of transport observed after several days of continuous operation was restored by flushing membranes with fresh ion exchange liquid. A major effort was devoted to preparation of thin, leak-free membranes; the resulting membranes endured operating conditions without mechanical failure.

Jan 1, 1982

By Oliver Bowles

This report covers the character, properties, origin, occurrence, and uses of the traprocks and describes briefly the methods and equipment employed in quarrying and preparing them for market. Production of traprock occupies an important place in industry. In 1960 the output in the form of crushed stone reached nearly 58 million tons valued at $87 million. Traprocks are also shaped into blocks of dimension stone for monuments, building construction and decoration, and specialized products such as surface plates.

Jan 1, 1963

By C. Özgen Karacan

This study presents the results of core-log analyses from the exploration boreholes, the analyses of face advance rates, and the results of downhole monitoring studies performed in gob gas ventholes for calculation of changes in hydraulic properties in the longwall overburden at a mine site in southwestern (SW) Pennsylvania section of Northern Appalachian Basin. In the ?rst part of the study, coal measure rocks in overburden strata were analyzed and the locations where possible fractures and bedding plane separations would occur were evaluated. In the second part, the hydraulic conductivities were computed by two different slug test analyses methods using the water level changes measured in gob gas ventholes as longwall face approached. Hydraulic conductivities were analyzed with respect to the changes in overburden depth, the locations of the borehole, and mine face advance rates. These data were used to interpret the potential productivities of the gob gas ventholes as a result of fracturing and changes in hydraulic conductivities. The general results showed that the probability of fracturing and bedding plane separations in the overburden increase between strong and weak rock interfaces. Also, the probability of bedding plane separations increases as the interface is close to the extracted coal seam. Evaluation of slug tests showed that the hydraulic conductivity developments in the boreholes and their potential production performances are affected by the underground strata and the roof materials. In situations where the roof material is stiff and thick, the development of high permeability fractures around the borehole will be less. Results also indicated that borehole location with respect to face position affects the fracturing time and permeability evolution as well. Greater overburden depths generally cause earlier fracturing as longwall face approaches, but eventually result in lower hydraulic conductivities and potentially less effective boreholes. Increasing mining rates also resulted in generally lower hydraulic conductivities in the overburden. The results of this study were intended to improve the interpretation of gob gas venthole performance and to provide better siting of these boreholes.

Jan 1, 2009

Introduction The NIOSH Office of Mining and Construction Safety and Health Research has redesigned its Mining Safety and Health Web topic page. The updated page incorporates a significant amount of new safety and health information, plus an improved layout to better serve stakeholder needs. It also provides back-ground information about the NIOSH Mining Research Program, including research awards, core competencies, unique labs, community and educational outreach, and a brief discussion of how the research program is structured. The new Web topic page can be found at www.cdc.gov/niosh/mining. "Search" Feature The redesigned Web topic page features improved search capabilities. The "Search Mining" feature on each page lets you search only the NIOSH Mining Safety and Health Web topic page. The user can still search the entire NIOSH Web page by using the "Search NIOSH" option. New Safety and Health Topics Developers expanded the "Safety and Health Topics" and reorganized the site to make it easier to find information. Each topic link now has a significant amount of new and updated information, as well as links to related topics of interest. Safety and health topics include dusts, diesel exhaust, hearing loss, contact with electric current, fires, explosives, ventilation, emergency management, new and older workers, and education and training. All topics can be accessed from the home page (Figure 1). Publications Although the Web topic page highlights many of the most requested publications on the safety and health topic links, you can find a complete list of downloadable publications as well. More than 600 mine safety and health publications are now downloadable from the page. Short summaries let the user quickly identify publications of interest. Products The updated Web topic page offers more than 120 NIOSH mine safety and health products, including training exercises, toolbox talks, videos, computer software, guides, and checklists, many of which are downloadable. If not, instructions are given on how to obtain copies. Some of our products include: • Software to analyze horizontal stress, design pillars for longwall mines, and select roof bolts for ground control. • Educational software including the Hearing Loss Simulator, which simulates the effects of noise and aging; and Coal Country, which teaches children about coal formation, mining techniques, and everyday uses of coal. • Utility software including the HazCom Helper software to assist individuals in writing a HazCOM plan, as required by the Mine Safety and Health Administration (MSHA), to track hazardous chemicals at their mine sites. • Guides for troubleshooting roof support systems, under-ground workstation design, and seating design. • Training exercises and videos that can be used for safety training. Data and Statistics General mining statistics are used by a wide variety of stakeholders. The NIOSH Mining Web topic page offers statistical graphs, tables, maps, fact sheets, and other publications that document the mining population, injuries, fatalities, diseases, and occupational exposures for all mining commodities. If users prefer to analyze data themselves, downloadable files of MSHA data are available. These cover employment, production, injuries, fatalities, and accident data from 1983 to the present and are available in both SPSS® and dBASE® formats.

Jan 11, 2005