Search Documents

By J. P. Harrison, J. A. Hudson.

ABSTRACT: When considering the rock stress component of rock mechanics design, the basic procedure is to consider the pre-existing stress-state in the rock mass and then estimate the disturbance to this stress state as a result of engineering excavation. Failure criteria are applied to the final stress state to establish whether failure will occur. However, during the evolution of the stress state, the failure locus may be reached before the anticipated failure state and, in this case, failure will occur unexpectedly. This indicates that the complete stress path (defined as the variations in magnitudes and orientations of the stress tensor components resulting from engineering-induced or natural changes) must be considered. We list a set of stress path principles with their corollaries and then introduce a new and powerful method for simultaneously illustrating changes in the six independent components of the stress tensor. This method plots the magnitudes of the principal stresses above their orientational paths on the hemispherical projection, to provide a three-dimensional stress path locus for each of the three principal stress components. In connection with this presentational device, we illustrate a number of concepts associated with the stress path in rock engineering. For example, we show how the minor principal stress approaches zero at an unsupported excavation face, the interchange of the trajectories of two principal stresses when their magnitudes become equal, and the influence of the bounds on the principal stresses given by strength criteria. RESUME: Si on s’interesse à la composante “contrainte” lors d’un dimensionnement en mécanique des roches, la méthode de base consiste à considérer l’état de contrainte pré-existant dans le massif rocheux, puis d’estimer la perturbation à cet état générée par l’excavation projetée. Des critères de rupture sont appliqués à l’état de contrainte final pour établir si une rupture va se produire. Cependant, lors de l’évolution de l’état de contrainte, la surface critique peut être atteinte ce qui provoquera une rupture anticipée et, dans ce cas, cette dernière sera inattendue. Cela indique que le chemin de contrainte complet (défini par les variations de l’intensité et de l’orientation des composantes du tenseur des contraintes liées à des causes anthropiques ou naturelles) doit être pris en compte. Nous présentons un ensemble de règles pour les chemins de contraintes ainsi que leurs corollaires et, ensuite, nous introduisons une méthode, nouvelle et puissante, pour présenter simultannement les changements des six composantes du tenseur des contraintes. Cette méthode consiste à tracer l’intensité des contraintes principales sur le chemin d’orientation des contraintes à l’aide d’une projection hémisphérique afin d’obtenir le lieu, en trois dimensions, de chaque contrainte principale. En relation avec cet outil de représentation, nous illustrons certains concepts associés au chemin de contrainte en ingénierie au rocher. Par exemple, nous montrons comment la contrainte mineure tend vers zero à la surface d’une excavation sans soutenement, le changement de direction des deux contraintes principales quand leur intensité deviennent égales, et l’influence des conditions aux limites sur les contraintes fournies par un critère de rupture. ZUSAMMENFASSUNG: Bei ingenieurmassigen Taetigkeiten in Felsgesteinen ist es noetig die ungestoerten Gesteins Stress Componenten, die vor einem anthropogen Eingriff im Gestein vorhanden waren, zu kennen und erst dann Vorhersagen ueber Stoerung des Stress Zustandes, der durch einen ingenieurmaessigen Eingriff hervorgerufen wird, herzuleiten. Kriterien fuer das Versagen werden im letzten Stadium, des Stress Zustandes angewendet, um zu erfahren ob ein Versagen wohl eintreten wird. Es ist jedoch zu beachten, dass waehrend des Stress Aufbaus ein oertliches Versagen eintreten kann, welches vor dem eigentlichen, erwarteten Versagens Zustand auftritt. Diese Moeglichkeit weist darauf hin, dass der gesammte “Stress Path” (definiert durch die Variationen der Stress Tensor Komponenten in Richtung und Groesse, hervorgerufen durch ingenieurmaessig hervorgerufene oder natuerlich Vorgaenge) betrachtet werden muss. Wir fuehren eine Liste der “Stress Path” Prinzipien auf und stellen dann eine neue und wirksame Methode zur gleichzeitigen Darstellung der sechs unabhaegigen Komponenten des Stress Tensors vor. Diese Methode stellt die Groesse der “Principal Stresses” in Abhaengigkeit von ihrem rauemlichen Weg auf einer hemispherischen Projektion dar und erlaubt hiermit eine drei dimensionale Darstellung fuer jeden Ort des “Stress Path’s” in die drei Haupt Stress Komponenten. Im Zusammenhang mit der hier gegebenen Darstellungsart, verdeutlichen wir eine Reihe von Konzepten in der Felsmechanik. Wir zeigen zum Beispiel, wie der “Minor Principal Stress” Null zustrebt an einer Wand von einer nicht abgestuetzten Ausschachtung, den Austausch von Trajektorien zweier “Principal Stresses” wenn ihre Groessen sich gleichen, und den Einfluss der Groesse von “Principal Stresses” bei gegebenen Kriterien des Festgkeits Versagens.

Jan 1, 2003

On Friday, 18th April, 1986, Stefen Kenneth de Kok passed away peacefully at his home in Johannesburg after a short illness. New President of FSPE Mr R.G. (Bob) St Leger took office as President of The Federation of Societies of Professional Engineers on 1st July, 1986.

Jan 1, 1986

By R. I. Klintworth

The multi-reef area of Cooke 3 Shaft provides a unique mining challenge on account of the very thin middlings between the pay bands and the marginal values of the reef. It is uneconomic or impractical, because of the excessive heights, to mine the middlings using conventional stoping methods. The development of suitable mining methods is discussed with particular emphasis on the control of water inflow and the policy of not jeopardizing or sterilizing other reef horizons by the mining method implemented. No definite solution is currently available, but with the aid of instrumentation, computer analyses and mechanized mining equipment, the mine continues to attempt to maximize extraction and profits.

Jan 1, 1988

By J. E. Furze

World-wide hikes in the oil price and the prospect of future scar cities of liquid and gaseous fuels have given enhanced status to the South African coal industry. It is thus understandable that the colloquium held at Wit bank on 3rd and 4th October, 1979, and organized jointly by the South African Institute of Mining and Metallurgy and the South African Coal Processing Society should have attracted more than 400 delegates.

Jan 1, 1979

By A. J. Barrett

Backfilling at Vaal Reefs during the experimental phase has been carried out using cyclone-separated tailings which are transported underground hydraulically by means of a borehole. The selected tailings are piped from the borehole to the stope and then, after the addition of a flocculant, deposited in place via single or multiple nozzles. The successful performance of the backfill/stope system relies not only on the actual quality of the placed material, but also on the effective operation of stope filling. The success of stope filling relates to the complex, time- dependent interaction of backfill, stope and barricade materials, and the transport and placement procedures used. A comprehensive laboratory testing programme was carried out on backfill materials at Vaal Reefs in conjunction with the experimental stope- filling operation. The range of testing techniques corresponds to the requirements of each stage of the backfilling process. Where necessary, new or alternative techniques were sought during the course of the experiment to satisfy and facilitate better understanding of the different processes. These techniques comprise both routine quality control testing and research-oriented testing. The laboratory testing techniques appropriate to each stage of the backfill process are briefly discussed. This paper presents the main conclusions of the study and identifies areas for further research.

Jan 1, 1988

By M. H. Moys

Accurate models of mill power are becoming more necessary as the design, operational, and control requirements for grinding mills become more stringent. Models of mill power are reviewed briefly, and a new semi-phenomenological model is derived. The conventional torque-arm model for mill power is combined with a model of the tendency of the load in a mill to centrifuge at high speeds, to describe mill power that can be related to several design variables (such as mil geometry, mill speed, and liner design) and control variables (such as load volume, slurry rheology, and mill speed in the case of variable-speed milling). The semiphenomenological nature of the model allows rational conclusions to be reached concerning the effect of various aspects of mill-load behaviour on mill power. The model is shown to be capable of describing reality with much greater accuracy than is achieved by empirical models such as the Bond model.

Jan 1, 1993

Members are advised that the Council has decided to change the format of the Journal from the present size to the standard international A4 size with effect from August, 1969. By making this change we will be conforming to more general practice today in regard to publications and this should effect certain economies and facilitate selling of advertising space. It has been arranged that in future the publication of the Journal, including advertisement sales, will be handled by Kelvin Publications (Pty.) Ltd. who are already doing this work satisfactorily for the Mechanical and Electrical Institutes. While making these changes, the opportunity is taken of redesigning the outer cover of the Journal to incorporate the new coat of arms. The Council trusts that these changes will meet with the approval of members.

By S. K. Lahiri, K. C. Ghanta

Design of industrial slurry pipelines is usually performed by applying semi-empirical procedures, requiring a significant experimental study for each project. The mechanisms of suspension flow are not yet completely understood and existing predictive models cover only some aspects of uniform or closely graded particle slurry flows. This paper presents a computational technique for prediction of the velocity and concentration profile in slurry pipelines based on computational fluid dynamics. This model gives numerical solutions for the concentration and velocity distributions in the pipeline cross-section. The model prediction and experimental concentration and velocity profiles were found to be in good agreement. Keywords: pressure drop; concentration profile; particle diffusivity; slurry flow.

Jan 1, 2007

By F. Lanaro, K. Röshoff, R. Christiansson, L. Jing

This paper presents the results of a project for developing a methodology for empirically determining some of the mechanical properties of the rock mass at the Äspö Hard Rock Laboratory, Southern Sweden. Using the equations available in the literature, the deformation modulus, friction angle, cohesion and unconfined compressive strength of the rock mass were estimated. A comparison of the results using different classification methods (Q, RMR, GSI, RMi, Ramamurthy’s) was made to estimate the range of variations in the mechanical properties with the considerations of: i) the quality/quantity of the geological data; ii) the technique for partitioning of the rock mass into homogeneous domains; iii) the sensitivity and subjectivity of the empirical methods; and iv) the need for validating the empirical methods against a test case. Cet article présente les résultats d’un projet visant à établir une méthodologie, pour déterminer, de façon empirique, les propriétés mécaniques de la masse rocheuse. En utilisant les corrélations disponibles dans la littérature, quelques-unes des propriétés de la masse rocheuse ont pu être déterminées (module de déformation, angle de friction, cohésion, force de compression illimitée). Une comparaison des résultats obtenus par différentes méthodes (Q, RMR, GSI, RMi, de Ramamurthy) a permis d’établir une échelle de variations des propriétés mécaniques et de formuler une série de recommandations concernant : i) la qualité/quantité des données géologiques ; ii) la technique de partition de la masse rocheuse dans des domaines homogènes ; iii) la sensibilité et la subjectivité des méthodes empiriques ; iv) la nécessité de valider les méthodes empiriques à l’aide de nouvelles études de cas. Dieses Paper präsentiert die Ergebnisse eines Projekts mit dem Ziel, eine Methodik für die empirische Festhellung von mechanischen Eigenschaften im Gesteinmassiv zu etablieren. Durch Verwendung der in der Literatur zugänglichen Korrelationen, wurden einige Eigenschaften des Gesteinmassivs festgestellt (Entstellungsmodul, Reibungswinkel, Kohäsion, unbeschränkte Kompressionsstärke). Ein Vergleich der Ergebnisse unterschiedlicher Methoden (Q, RMR, GSI, RMi, Ramamurthy’s) wurde durchgeführt und dies erlaubte die Feststellung der Variationsskala von den mechanischen Eigenschaften, sowie eine Reihe Empfehlungen für: i) Qualität/Quantität der geologischen Dateien; ii) die Technik für Teilung des Gesteinmassivs in homogene Domäne; iii)die Empfindlichkeit und Subjektivität der empirischen Methoden; iv) das Bedarf die empirische Methoden gegen neue Fallgeschichten zu validieren.

Jan 1, 2003

By C. E. Dohm

The paper serves to show the importance of both a geological model and geostatistical model that support one another in mineral resource evaluation. It highlights the advantage of reference models for the geometry, the geological, statistical and geostatistical models of various orebody types and introduces a method for quantifying the combined uncertainty in these models. The example presented reveals how the above levels of information can be applied to add value to a resource evaluation process. It is a generic example in that it is the technique of combining uncertainty in the geological model (boundaries) as well as the grade model to assess the overall risk in the estimation of the resource. Data from the coal industry is used to illustrate the techniques. The geological uncertainty is considered via categorical simulations and these are combined with simulations of the variables (grades, thickness,) being estimated in the resource. The simulation techniques used are based on the application of GSLIB software1and a general discussion of the two simulation processes is included. In conclusion the paper demonstrates how the results of two types of conditional sequential simulation can be combined to produce confidence limits that take both uncertainties into consideration. This technique does not replace the resource estimation; it serves as an additional tool to quantify confidence in the resource evaluation model. The topics considered in this contribution are in terms of continuous improvement of mineral resource evaluation.

Jan 1, 2003

By N. R. Shoko, J. Chirasha

Refractory design remains the most fundamental factor in furnace construction. Refractory design details and proven technology consideration is of paramount importance to come up with an optimum furnace life and to maintain productivity in the life span of the furnace lining. The failure to produce a technically or operationally durable refractory design lining could give rise to pre-mature deterioration of the refractory lining and furnace shell. The premature failure of the furnace lining will lead to extensive heat losses, furnace bath shift, change in taphole orientation and alteration of the Pitch Circle Diameter. A combination of these were experienced at Zimbabwe Alloys? new high carbon ferrochrome furnace. The Zimbabwe Alloys experience has shown an excellent furnace performance in the first two years of operation although signs of an anomaly showed within the first six months of the new furnace. Production slowed down due to induced problems from refractory failure causing furnace distortions impacting on the availability of the furnace and smelting capacity. This paper presents the lessons learnt, measures taken to deal with the premature failure and constraints within which the situation was managed.

Jan 1, 2007

By N. A. Barcza

An investigation was conducted into the reactions between the slag system MnO-CaO-MgO-SiO2(AI2O3) and the alloy system Mn-Fe-Si-(C). Synthetic slags representative of plant melts and a plant alloy were reacted in alumina crucibles at temperatures of 1400°C, 1450°C, 1550°C, and 1600°C. In similar experiments, slags were used that comprised a South African manganese ore with various amounts of lime and several synthetic alloys with various silicon contents and manganese-to-iron ratios. These experiments were conducted in a vertical molybdenum-wound resistance furnace with full temperature control. Slag-to-alloy ratios were also varied during the tests. The rate of reduction of Mn.O3 and the MnO from the slag by the silicon in the alloy was extremely rapid, most of the reaction being completed within five minutes. The strongly exothermic nature of the reaction resulted in considerable generation of heat at the slag-alloy interface, causing convectional stirring of the contents of the crucible and promoting the rate of reaction. Equilibrium was usually attained after fifteen minutes. The major limitation governing the recovery of manganese is the need for the silicon content of the alloy to meet a maximum specification of 2 per cent. Higher concentrations of silicon in the final alloy of between 8 and 12 per cent favour good recoveries of manganese from the slag, but, since such an alloy is not salable, lower recoveries must apparently be tolerated. In alloys of 2 per cent silicon, low activities of the silicon are responsible for poor recoveries of manganese. The activity of MnO in the slag can be increased by moderate additions of CaO and small amounts of MgO, i.e., by an increase in the basicity of the slag.

Jan 1, 1979

By J. M. Stewart

The purpose of my few comments is to try to create a healthy perspective to constructively link considerations of the sessions to follow to those of the earlier sessions. I propose to do this by considering some of the issues and priorities related to the development of backfill systems and technology for South African gold mines.

Jan 1, 1988

By M. E. E. Douglas, A. K. Haines, D. I. Nicol, C. M. Olëm, W. M. Craig, G. D. Louw

A description is given of the design of the continuous ion-exchange demonstration plant at Blyvooruitzicht Gold Mine, including details of the process design, the column construction, and the control system. The operating and process results gathered over a period of seventeen months are summarized, and development work and modifications to the process are discussed. It is concluded that the system comprising continuous loading and continuous elution is technically feasible and can be scaled up with confidence.

Jan 1, 1978

By B. J. Pieters

The paper describes the difficulties experienced with inferior coking coals as Iscor began using larger blast furnaces for the production of liquid iron. Research conducted at Iscor from 1977 to 1979 showed that benefits could be gained from the use of partially briqueted charges, and it was decided to install briqueting plants at the Vanderbijlpark and Newcastle Works. Details are given of the later plant, which was supplied by a consortium consisting of Voest Alpine, Didier Engineering, and Sumitomo Metal Industries. Sumitomo also supplied information on the optimization of coke quality along the lines of their Sumicoal System. The results have been a marked improvement in coke quality, much better blast-furnace operation, and increased productivity.

Jan 1, 1991

By J. M. Stewart

Although the incidence of heat stroke in South African gold mines is small, work continues on its reduction. This paper proposes limits of heat stress that are applicable to South African underground conditions, with the warning that they should not be extrapolated to other situations without careful consideration having first been given to their limitations. These limits of heat stress take physical and physiological considerations into account, and they correspond to there being a 10-6 risk of an essentially nude man developing a rectal temperature in excess of 40°C. It is recommended that further work should be undertaken on the development of equations for the calculation of the heat transfer from clothed men, the derivation of equations that quantify the physiological conductance and sweat rate response of humans, and on establishing the frequency distributions that describe variations in rectal temperature response between individuals in different types of environment.

Jan 1, 1981

By Y. Suzuki, H. Yoshida, K. Sakaguchi, K. Matsuki, M. Minami

To estimate three dimensional in-situ stress at great depth, Downward Compact Conical-ended Borehole Overcoring (DCCBO) technique, which is one of stress relief methods, was developed. DCCBO technique can be applied to a water-filled vertical/sub-vertical borehole. In in-situ tests, the bonding device and the cleaning system were verified to work well in a water-filled borehole with cuttings on the bottom. Um dreidimensionale in-situ Beanspruchungen in großen Tiefen abzuschätzen, wurde das Downward Compact Conical-ended Borhole Overcoring (DCCBO) Verfahren entwickelt, wobei es sich um ein diese Beanspruchungen entlastendes Verfahren handelt. Die DCCBO Technik kann auf wassergefüllte vertikale und subvertikale Bohrlöcher angewandt werden. Bei den in-situ Tests wurde die Einsatzfähigkeit der Verbindungsvorrichtung und des Reinigungssystems für wassergefüllte Bohrlöcher mit Einschnitten am Boden bestätigt. La technique de Downward Compact Conical-ended Borehole Overcoring (DCCBO) ou ‘Surcarottage par sondage à extrémité conique compact dirigé vers le bas’, qui est une méthode de détente des tensions, a été développée pour calculer les tensions in-situ à trois dimensions à grande profondeur. Cette technique peut s’appliquer à des sondages verticaux/sub-verticaux remplis d’eau. Au cours des essais in-situ il a pu être vérifié que le dispositif de liaison et le système de nettoyage fonctionnaient bien dans un trou de forage rempli d’eau avec saignées au fond.

Jan 1, 2003

By P. F. Sorensen

A simple mathematical model is presented that relates the 'head' developed at the surface of pulp in a tank to the power dissipated by the air in producing it. The value for the head is then used in the calculation of the superficial circulating velocity of the pulp and the area of the overflow, and the product of these two values gives the pumping rate of the pulp. Thus, the superficial circulating velocity, and hence pumping rate of the pulp, are related directly to the flow-rate of the air. This hypothesis was tested with good results in an air-agitated pachuca tank (of 1 m in diameter) fitted with a draught tube. The method can also be used for the prediction of the pumping rates in production-scale vessels.

Jan 1, 1985

By M. J. Nicol

This paper ,examines the kinetics of the extraction of uranium from acid sulphate solutions by strongbase anionexchange resins. Parameters such as the concentration of uranium in solution. the agitation of the resin beads in solution. the size of the resin beads. and the degree of cross-linking within the resin matrix were varied. and the effec ts on the kinetics are reported. The applicability, of various empirical kinetic models to the description of the data is assessed, and an attempt is made at the modelling of the rate data in terms of established theories about the diffusion of ions through films of stagnant liquid and through spherical beads of resin.

Jan 1, 1980

By E. C. Stoltz

Note: An electric tin smelter for the processing of Iow-grade tin concentrates in South Africa by E. C. STOLTZ, Pr. Eng., B.Sc. Eng. (Rand) Gold Fields of South Africa Limited is the largest producer of tin in the form of concentrates in South Africa, more than 55 per cent of the South African tin production being produced by the tin mines of the Group. Most of these concentrates are exported to be custom-smelted in overseas smelters, but the modern tendency is for tin-mining countries to establish their own smelters.

Jan 11, 1976