Search Documents

By H. J. Oberson, J. H. Brown

Comminution devices such as rod or ball mills are characteristically nonselective in their operation in that all material fed to a mill is ground to some extent. This is unfortunate when the object of comminution is liberation, for not only is energy expended in breaking pure gangue particles wasted, but, since gangue is frequently the predominant phase, the opportunity for such loss is great. Ideally, in this application a comminuting device should develop fracture only in locked particles. In the present investigation an attempt was made to use the large density difference which may exist between minerals to prevent comminution of one while grinding the other. EXPERIMENTAL MATERIALS AND EQUIPMENT The two minerals used in this work were -8-mesh galena and -8+ 20-mesh quartz. All tests were made on 2000-g charges containing 50 pct by weight of each mineral. Heavy media suspensions consisted of -100-mesh ferrosilicon in water. For grinding, a laboratory mill 10 in. diam by 12 in. long was filled to about 30 pct of its volume with either a ball or a rod charge. The balls ranged in size from 3/8 to 1 1/8 in. in diam; the rods ranged from 5/8 to 1 1/4 in. diam by 11 in. long. EXPERIMENTAL PROCEDURE In all tests employing heavy media, the ground pulps were treated as follows: 1) After recovering the ground charge from the mill but before drying, the pulp was wet screened on 200 mesh. 2) After drying the + 200-mesh product from step 1, the ferrosilicon was removed magnetically. 3) The nonmagnetic quartz and galena product from step 2 was sized on 10-mesh through 200-mesh screens. 4) The mineralogical composition of each screen fraction was determined by measuring its specific gravity. The specific gravity was related to the weight of galena in the fraction through the relationship

Jan 1, 1961

By C. N. Reid

Slip-line studies on deformed chromium single cvystals showed the usual bcc behavior. At room temperatuve, cross slip was prevalent—slip was not confined to a given plane, but the slip direction was (111). At -10O0K, slip occuvred on (110) planes, twins on(112) planes, and cleavage on (1001 planes. A single-crystal tensile specimen with an axis close to [011] showed a pronounced yield drop and high strain rate sensitivity which zclere used to derive relevant parame tevs in a dislocation dynamics treatment. Transmission electron microscope studies confirmed the existence of (110) slip planes and showed ecidence of loops punched out by precipitates and of grown-in dislocations promoting tangling. OF recent years experimental studies have been made of the deformation characteristics of single-crystal molybdenum and tungsten, but very little has been published on the behavior of single-crystal chromium. During a study of the mechanical properties of chromium, single-crystal studies were made which have already been partially described.&apos; However, additional information was generated which was not directly relevant to the main theme of Ref. 1, and, therefore, was not reported. In view of the need for complete documentation of deformation modes, the experimental observations made on the deformation of single-crystal chromium are summarized here, together with an electron-microscope study of the associated dislocation structures. It was found that, in terms of the deformation modes, chromium is a conventional bcc metal, showing a very pronounced yield-point phenomenon. Further, it was found that the flow strength of these crystals is very sensitive to the strain rate. Finally, the crystals were observed to contain many unidentified precipitates, which often were associated with prismatic dislocation loops. EXPERIMENTAL METHODS Single crystals were grown from rods of wrought chromium by the method of zone annealing. Rods of "1/4in.-diam were supported vertically in an argon atmosphere while an induction coil was moved up the rod at 1 in. per hr. The power was adjusted to just below that required for melting, and the process produced single crystals in about 30 pct of the rods used. The orientations of the crystals, in general, lay near [011] and are summarized in Fig. 1. Before this treatment, the wrought material contained 35 pprn C, 68 ppm O, and 12 ppm N.* An analyzed single crystal *Usual metallic impurities found in iodide chromium are: Al, 5 ppm; Ca, A ppm; Cu, 2 ppm; Fe, 75 ppm; Yg, 0.5 ppm; Yn, < 3 ppm; Mo, < 3 ppm; Ni, 4 ppm; Si, < 20 ppm; Ti, < 1 ppm; V, 4 ppm; Zr, < 3 ppm. contained 10 pprn C, 79 ppm O, and 50 pprn N. Tension and compression specimens were shaped from the crystals by mechanical grinding, followed by the electrolytic removal of about 0.010 in. from the surface in a perchloric/acetic acid bath. All specimens had a gage length of 0.75 in., and tension specimens had a diameter of 0.100 in., while that of the compression samples was 0.200 in. Mechanical tests were carried out at a rate of 1.3 pct per min, and temperatures below 0°C were attained by means of a nitrogen cryostat similar to that of Wessel.2 EXPERIMENTAL RESULTS Modes of Deformation. In addition to the tensile properties of these crystals, which are described in Ref. 1, deformation markings on the surface were studied. Crystals A and F, Fig. 1, were deformed in tension at 300°K to 10 and 16 pct strain, respectively. The surfaces contained visible slip lines, about 1 C( apart, composed of both straight and wavy segments. They did not define a single plane, and so determination of the slip plane was not possible. However, the slip direction was deduced by comparing the axial orientations of the crystals before and after deformation. Fig. 2 is representative, and shows that the axis ro-

Jan 1, 1968

By Samuel Taylor

IT is customary for the president of an engineering society, in his annual address, to describe either some engineering problem with which he has beer connected or to review the work of the society during his administration. My first thought, this being the sesquicentennial year of our nation, was to review the advance in coal mining for the past fifty years, during which period I have been more or less intimately con-nected with the bituminous coal industry, and have personally witnessed most of the great changes which have occurred in methods and machinery used in the production of coal, but preparation of the requisite address would take more time than could be spared to prepare it, and its presentation would consume so much time that it .would not be suitable. The new arrangement providing for giving the presi-dent&apos;s address at the business meeting makes it more .appropriate to review the work of the Institute during the past year, together with some suggestions which appeal to me as being of advantage to the future wel-fare of the Institute, which I will try to do briefly. The work of the business office has been reviewed in the Secretary&apos;s report and it will not be necessary for me to dwell on it. Suffice it to say, it seems to be going along very well. Additional work could be done which would be to the advantage of the Institute, if we had the money with which to defray the necessary ex-pense incident to it, but I will refer to this again later. I would be derelict if I did not refer to the splendid work of the Secretary and the Assistant Secretary. Keeping in touch with all the sections, which number now about 26, and affiliated student societies which number 40, besides special committees, and represent-ing the Institute on various boards, provides work enough to occupy the Secretary&apos;s time almost exclu-sively. In addition to this the Secretary and the As-sistant Secretary have the work of editing and publishing the TRANSACTIONS of the Institute; the issuing of the magazine, MINING AND METALLURGY, in the splendid manner in which it goes out to the mem-bership is no light task and I think they should receive the commendation of the membership for this work.

Jan 3, 1927

By S. G. Dixit, A. K. Biswas

The flotation and adsorption behavior of ilmenite, monazite and zircon have been studied with sodium oleate as the collector and pH as the principal variable. The maxima in the flotation and adsorption properties of any of the above minerals fall within similar pH ranges. The bell shaped pH versus adsorption magnitude (r) curve is explained on the basis of collector concentration (Co and the concentration of hydroxyl ion (COH-) acting as the depressant. An equation of the type: 1 =KiCor~K2 Coh-/Coi-is proposed to account for the experimental data. The beach sand deposits along the sea coast in Southern India contain ilmenite, monazite, zircon, rutile and sillimanite as valuable minerals while quartz, garnet, shells and traces of hornblende form the gangue. A typical composition of the deposits is reported to be as follows:&apos; Ilmenite 75%, Zircon 4-6%, Rutile 3-4%, Monazite 2 - 4%, Garnet 2 - 5% and the rest 8 -10%. Selective flotation of beach sand constituents has been reported by many workers.2-4 The fatty acid soaps have been invariably used as collectors. It is seen that all the valuable constituents of the beach sand are efficiently floated by soap collectors such as sodium oleate. In order to selectively float the beach sand constituents, it is necessary to use some depressants such as sodium silicate.3 The physicochemical parameters that govern the flotation of these minerals are yet to be studied in detail. In the present article, the findings on the parallel studies on the flotation and adsorption of the systems — ilmenite-sodium oleate, monazite-sodium oleate and zircon-sodium oleate — are being reported. In these correlative studies on adsorption and flotation of beach sand minerals, ilmenite (FeTiO3), monazite (Ce, Dy, Nd) PO4 and zircon (ZrSiO,) have been selected because they represent three important

Jan 1, 1970

By T. F. Archbold, R. E. Grace

The use of interference colors is the simplest experimental way to determine the approximate film thicknesses of oxides formed on liquid metals. A large amount of data under various conditions can be obtained easily and quickly. The oxidation of liquid lead has been studied by several investigators,1-5 but all of these studies have been on thick oxide scales. The purpose of- this work was to investigate the range 0 to 2000A film thickness. By using electron diffraction, Jenkins concluded that the surface of the film on molten lead is yellow orthorhombic PbO with the (110) planes parallel to the surface. This was confirmed by Shimaoka and Yamai7 who also used electron diffraction from the melting point of lead to 730°C. The rate of oxidation of pure liquid lead in air was measured in the temperature range 453" to 643°C by observing the rate of formation of interference colors on static lead baths. Approximately 170 g of lead (99.999 pct) was placed in a refractory dish having a working surface of 13.8 sq cm. This crucible was placed in a deep-well resistance furnace open to the atmosphere. The times at which the various interference colors appeared, after wiping the molten metal surface clean, were determined at 453", 533°, 600°, and 643°C. Elapsed times were determined with a stopwatch and all colors were estimated by eye. Bath temperatures

Jan 1, 1959

By K. E. J. Rapperport, C. S. Hartley

The only slip system observed in zirconium crystals deformed at 77", 575", and 1075OK was (1010) [1210] with a critical resolved shear stress in tension of 1.0 kg per sq mm at 77°K; 0.2 kg per sq mm at 575 °K; and 0.02 kg per sq mm at 1075 OK. The active twin planes were {1012}, (1121}, (11221, and (11233) with varying temperature dependence. A detailed analysis for the slip direction using Laue spot asterism is appended. NeARLY all metals of the hexagonal close-packed structure exhibit basal slip, i. e.,(0002)<1120>- type slip. This is true of magnesium,&apos; zinc,&apos; cadmium,3 beryllium,4 titanium,= yttrium,6 and rhenium.Many of these such as titanium 5&apos;8-&apos;0beryllium,4&apos;" magnesium, and zinc13&apos;14 display other slip modes even at room temperature, and nearly all have been reported to slip on other systems under particular loading or temperature conditions of testing. As is shown in this paper, basal slip was not found at any of four test temperatures from 77" to 1075°K in hexagonal close-packed zirconium under the simple loading conditions of tension and compression, even though in one case the resolved shear stress on the inactive (0002) <llgO> system was twenty-five times higher than the critical resolved shear stress on the active (1010) [1210] system. This result is consistent with prior studies on the active deformation processes in zirconium deformed at room temperature. &apos;&apos;-I7 SPECIMEN PREPARATION A) Material—The zirconium used in this work was of two types: 1) as-deposited reactor grade crystal-bar, and 2) arc-melted and forged reactor grade crystal-bar. Typical chemical and spectrographic analyses of these materials as received, and after hydrogen removal and crystal growth are given in Ref. 17. Crystals of type 1) above have the letter prefix (A) and those of type 2) have the prefix (B) throughout this paper. B) Crystal Growth— he zirconium was machined into rectangular parallelepipeds about 0.2-in. scl in cross section and 2 in. iong. These were hand polished through 4/0 abrasive paper, electropolished, given a hydrogen removal anneal, and subjected to long-time anneals at 840 °C in vacuo to produce usable crystals.&apos;7 A second technique used to obtain large crystals was to cycle the samples two or three times between 1200" and 840°C, allowing them to remain at the higher temperature for about 4 hr and at the lower temperature for 5 days.17 These techniques yielded some grains which occupied the entire cross section of the bar and were as long as 3/4 in. C) Orientation Determination—After the growth of large crystals by thermal cycling, the samples were repolished with extreme care through 4/0 abrasive paper and electropolished. Metallographic examination after polishing showed the surfaces to be free of visible deformation traces. Standard Laue back-reflection X-ray techniques were used to find the crystallographic orientations of selected large grains with respect to a specimen face and edge. Fig. 1 shows the stereographic projections of the stress axes for the crystals used. The sharpness of the spots on the Laue photographs indicated that the crystals were of good quality. EXPERIMENTAL METHODS Nine crystals were deformed in tension at 77"K, nine in tension and five in compression at 300°K in previous tests,17 fifteen in tension at 575"K, and eleven in tension at 1075°K. All specimens were stressed by load increments. After a predetermined load was applied, the specimen was removed from the loading appratus and metallographically examined for deformation traces. An attempt was made to initially stress each bar so that some crystals slipped a small amount and others not at all. This was done to bracket the critical resolved shear stress. One bar of special orientation (B-11) was repolished and annealed at 1075°K for 1 hr after lower temperature deformation, before final deformation at 1075°K. In the other bars the loading by increments, followed by metallographic examination, was continued until the surface distortion would interfere with analysis, or until fracture. One example of a crystal pulled to fracture is shown in Fig. 2. This photograph shows a crystal (B-14C) which was pulled at 1075°K and failed by slip on two (10i0) planes. The approximate orientation of this crystal is illustrated in the figure. Specimens were deformed at 77°K in liquid nitrogen on a tensile machine using an insulated bucket with an internal hook to accept a clamped specimen.

Jan 1, 1961

For the third year in a row total value of the Nation&apos;s mineral production broke all previous records. A new peak of $20.4 billion was reached in 1964. So says the U. S. Bureau of Mines. The Bureau&apos;s preliminary estimate for 1964 is $800 million higher than the value reported for 1963, and $1.6 billion greater than the 1962 figure. The unprecedented demand for minerals, has stimulated development of new mines and expansion of processing capacity in many parts of the country.

Jan 2, 1965

By H. Rees

This paper supplements and brings up to date a report prepared earlier this year and presented at the Eleventh Pan American Railway Congress in Mexico City. Most of the original report is contained in this paper in order to acquaint the reader with the project background. On December 1, 1961, construction of this locomotive was completed. Stationary testing started immediately, and a host of problems in various areas were uncovered. Many of these had no relation to the use of coal in a direct fired gas turbine. All of them emphasized the problems which plagued previous projects of this kind. In 1944 the Locomotive Development Committee of Bituminous Coal Research, Inc., was formed to study the problems of combustion, coal handling, and fly ash removal which would have to be solved before coal could be used to fire a gas turbine. By 1947 this committee was composed of the chief executive officers of nine eastern railroads and five eastern coal companies. All of the members of this committee were vitally concerned in a coal fired gas turbine because coal cost only one-fourth as much per heat unit as fuel oil. A number of research projects were started to develop and test components on a small scale. This included work at John Hopkins University, Battelle Memorial Institute, Institute of Gas Technology at Chicago, Purdue University, and Southern Research Institute. By 1946 a pilot plant had been installed at the Dunkirk, New York plant of Alco Products Div. of American Locomotive Co. The U. S. Bureau of Mines made available to the Locomotive Development Committee (hereafter called LDC) a Houdry process gas turbine plant, originally destined for a Russian oil refinery. The full scale pilot plant was used to evaluate the results obtained from the small scale studies under actual gas turbine conditions. Operation of this plant disclosed a number of problems which had not been discovered in the small scale tests. By 1951 four 250 hr tests had been conducted with the Houdry gas turbine to test out a variety of equipment. The major problem concerned the removal of abrasive fly ash from the products of combustion so that wear on turbine blades would not be excessive. The first 250 hr test showed that the original fly ash separating equipment was inadequate. Large ash particles passing through the turbine blading were nicking the leading edges of the first row blades. At the conclusion of the second 250 hr test, erosion was so severe that the first row of stator and the first row of rotor blades were replaced. At the end of the third 250 hr test, it was necessary to replace the first three rows of stator blading. The fourth test was used to test out a new design fly ash separator developed by LDC and named the Dunlab tube. This device gave more encouraging results than any of the others tested. Early enthusiasm for overcoming major difficulties had resulted in placing an order in 1946 with Allis-Chalmers Mfg. Co. for a 3750 hp regenerative gas turbine. The gas turbine, together with associated combustion and ash removal equipment, coal handling equipment, generators and gear reduction unit was installed at Dunkirk by 1951. A 750 hr test was made in 1952 with the LDC-Allis Chalmers gas turbine power plant. At the end of this test it was necessary to replace the first four rows of both rotor and stator blading. Rows 5 and 6 did not require replacement. In 1953 the American Locomotive Co. joined with LDC and assumed an active role in equipment development and manufacture. During 1954 LDC-Alco operated the rebladed gas turbine 300 hr to determine if a new fly ash separator was adequate. Performance of the improved separator was considerably better, but trouble was experienced with clogged blowdown lines from the Dunlab tubes. When these lines clogged it permitted the passage of abrasive particles. In 1955 a total of 1421 hr was run. This included 243 hr of cycle operation on Union Pacific coal from the D. O. Clark mine at Superior, Wyoming. During the 243 hr a total of 370 tons of coal was consumed. The purpose of this test was to determine if U.P. coal was suitable for use in a coal fired turbine. It was the unofficial opinion that it was as good or better than the eastern coals that had been tested.

Jan 1, 1964

By A. L. Mincher, W. F. Sheely

Mechanical properties of columbium have been studied over the temperature range of -196 to 1093oC. The decreased strengthening influence of cold-work at temperatures below ambient has been interpreted in terms of the Peierls-Nabarro effect. Maxima in the rate of strain hardening observed during tensile testing in the range 250-600°C. have been correlated with interstitial impurities to indicate the temperature ranges at which carbon, oxygen, and nitrogen, respectively, are responsible for strain aging. THE growing need for structural materials for use above the useful service temperatures of the iron-, nickel-, or cobalt-base alloys has caused the refractory metals to be considered as potential engineering materials. These metals, which include columbium, tantalum, molybdenum, and tungsten, are called refractory because the lowest melting point among them,that of columbium, is about 1000°C higher than the average melting temperatures of conventional high-temperature alloys. They are all body-centered cubic transition metals and, as such, their mechanical properties have basic characteristics which distinguish them from the face-centered cubic metals. For example, all show a much steeper rise in strength with decreasing temperature below room temperature than do the face-centered cubic metals, and their mechanical properties are strongly influenced by interstitially dissolved impurities. In order that these new metals may be used efficiently, it is necessary that their characteristics of behavior be fully known. In this paper, the mechanical properties of columbium will be examined over a wide range of temperatures. In particular, the influences of cold-work and individual species of interstitial impurity atoms on mechanical properties will be described, and basic mechanisms which may control the observed characteristics will be explored. EXPERIMENTAL The material used in this investigation was Union Carbide Metals Co. columbium roundels consolidated to four 4-in. diam ingots, three by consumable-electrode arc melting and one ingot by electron beam melting. Impurity contents of the ingots and methods of ingot conversion and treatment are summarized in Table I. The only metallic impurity occurring in any significant quantity was tantalum at about 0.1 pct. Iron, silicon, titanium, and zirconium were each less than 0.015 pct; boron was 1 ppm or less. This should have no appreciable influence on properties. The electron beam melted material, being the purest, will be used as the basis for comparison in the discussions to follow. Tensile tests were conducted from-196 to 1093oC, on both cold-worked and fully recrystallized arc-melted and electron-beam melted columbium using standard 1/4-in. diam, 1-in. long gage length test specimens. A strain-rate of 0.005 in. per in. per min was employed until the 0.2 pct yield strength was achieved and then the strain-rate was increased to 0.05 in. per in. per min for the balance of the test. Samples were protected in an inert atmosphere at tests above 300°C. The tensile properties obtained on the electron-beam melted columbium, E, in both the cold-swaged and recrystallized conditions are given in Fig. 1. The yield strength data of Dyson, et al.,&apos; obtained on recrystallized electron beam melted columbium and the tensile strength data reported by Tottle2 on powder metallurgy columbium are included in Fig. 1. The material used by Tottle had been purified by vacuum sintering. There is excellent agreement between Dyson&apos;s data and those obtained in the present investigation. The tensile strengths obtained by Tottle were slightly greater than those obtained in this investigation on electron-beam melted columbium but varied with temperature in a similar manner. Tottle&apos;s data showed a maximum in tensile strength near 500°C, as did our data on electron-beam melted material, and also showed a small maximum at 300°C. The significance of these maxima will become evident later in the discussion. The tensile properties of cold-swaged and recrys-tallized arc melted columbium are plotted in Fig. 2. It was found that the properties of the recrystallized arc-melted columbium from all three heats showed very close agreement except at temperatures between about 500" and 800°C. A reason for this range of disagreement will be suggested in the discussion. The generally good agreement, however, attests to the ability of cold-working and subsequent recrystal-lization to erase the effects of the three different primary breakdown procedures and to produce nearly equivalent structures in the samples derived from the three different heats. wesse13 reported tensile data on columbium having interstitial impurity contents between those of the

Jan 1, 1962

By Henry Hebley

IN preparing this paper it has been the aim of the writer to keep the problems of both producers and consumers in mind. Until now, no attempt has been made to familiarize each group with the other&apos;s practice and limitations. This paper is an effort to acquaint the readers with some of the factors pertaining to the problem and cost of mining and preparing steam coal, and also to the economics of producing steam with such coal. In recent years all lines of endeavor have turned to intensive mechani-zation in order to lower the unit cost of production. The average fuel consumption in steam electric generating stations has dropped in 20 years from 4.0 lb. to 1.4.1b. per kilowatt-hour; while the modern power station can generate 1 kw-hr. on a fraction under 1 lb., or 13,000 B.t.u. coal. Also, the amount produced per man has in that same period risen from 3.8 to 8.2 tons, owing to the use of modernized equipment below ground for coal cutting, drilling, shooting, loading, hauling and hoisting. Unfortunately, the rapid speed of 5 tons per minute of operation at which the coal is loaded mechanically precludes any appreciable removal of impurities at the coal face, so that the raw coal is hoisted containing a markedly higher percentage of impurities than the hand-loaded coal, which was subjected to the scrutiny of the miner during loading. Also, during the past 20 years, certain seams of coal lying close to the surface have been made economically available by the improved design of electrically operated shovels and draglines for the removal of overbur-den running as high as 56 ft. This strip coal frequently contains so much ash in the raw state (Table 1) that it would have no sales value. There-fore, coal preparation must be adopted to beneficiate the raw product. Some seams in the United States have a decreasing ash content with decreasing size, owing, in all probability, to the fact that the coal is friable while the impurities are hard, causing a concentration of the low-ash material in the fine sizes. Illinois No. 6 coal being rather hard, naturally the reverse is true.

Jan 1, 1937

By N. K. Chen, R. Maddin

Columbium single crystals were deformed in tension and compression. Reorientation by X-rays and stereographic projections of slip traces indicate that plane of slip may be considered as (110). The plastic behavior is shown to be quite similar to the deformation of molybdenum single crystals. STUDIES on the crystallography of the deformation process in body-centered cubic metals have been renewed recently with investigations of iron single crystals1-" and molybdenum single crystals.4 It is now apparent that too many exceptions to the rationalization based upon the ratio of absolute testing temperature to absolute melting point by Andrade5 exist to permit more serious discussion of this type of analysis. The considerations of resolved shear stress utilizing only planes of the type {ll0}, {112), and {123)³,6 permit analysis of the deformation only on the basis of those three types of planes. The suggestions made by Elam7 and by Greninger8 in which the slip process is envisioned as a composite slip on two nonparallel {110) planes can be illustrated schematically in Fig. 1. It may be seen that an unresolved trace on any plane containing a <111> direction may be accomplished by varying the number of atoms participating in the composite process. By further varying the number of atoms in each plane but keeping the ratio of participating atoms constant, jogs could be obtained in the traces and hence wavy slip lines could be produced. Vogel and Brick&apos; studied the behavior of a iron single crystals in which they suggest that the plane of glide is "non-crystallographic" and may be predicted from the intersection between the great circle joining the slip direction and specimen axis with the great circle whose zone axis is the slip direction. In a more recent investigation on iron single crystals, Steijn and Brick" suggest that the slip mechanism may be considered as made up of a type of composite slip occurring on {110} and {112} planes. Evidence for a possible composite nature of the slip process has been presented for the case of molybdenum in the form of analysis of asterism and specimen axis rotation." Definite proof of a composite slip process must, however, await good electron microscopic resolution of the individual traces making up the unresolved optical trace used in determining the acting slip plane. The present investigation was undertaken to study the behavior of columbium single crystals not only in tension but also in compression since the specimen axis migration should indicate the plane or planes of glide in the same manner that the specimen axis migration in tension indicates the direction of glide. The orientations of eleven crystals investigated are shown in Fig. 2. Specific orientations are missing (those in the vicinity of [Ill] and [001] and consequently the effect of orientation on the crystallography of deformation could not be considered. Experimental Procedure The 1/8 in. rods (7 in. long) were subjected to an axial tension in vacuo while at temperatures in the vicinity of 2000°C for 2 to 4 hr. This treatment resulted in large cylindrical grains (about ½ in. long) occupying the entire cross section. A number of these rods were used for the tension studies by observing the behavior of the individual grains. For the compression studies, single crystals approximately % in. long by 1/8 in. in diameter were cut from the rods; the ends were ground parallel. All specimens were polished electrolytically in a solution of 15 cc HF(48 pct) and 85 cc H2SO4 (concentrated) using a platinum cathode, a current density of 0.04 amp per sq cm and a temperature between 25" and 60°C.10 Orientations were obtained using a Laue back-reflection method (3 cm film to specimen distance) with a ½ mm collimator 9 cm long. For the compression specimens, a reference mark was scratched on one of the compression sur-

Jan 1, 1954

PRESIDENT AND DIRECTOR DONALD B. GILLIES CLEVELAND, OHIO PAST PRESIDENTS AND DIRECTORS R. C. ALLEN CLEVELAND, OHIO D. C. TACKLING SAN FRANCISCO, CALIF. TREASURER AND DIRECTOR KARL EILERS NEW YORK, N. Y. VICE-PRESIDENTS AND DIRECTORS H. G. MOULTON NEW YORK, N. Y. HARVEY S. MUDD Los ANGELES, CALIF. PAUL -D. MERICA NEW YORK, N. Y. WILFRED SYKES CHICAGO, ILL. WILLIAM B. HEROY HOUSTON, TEXAS HENRY KRUMB NEW YORK, N. Y.

Jan 1, 1939

By John V. Beall

Probably it won&apos;t happen to us again in a thousand years, but it was very embarassing at the time. It is only because of certain matters that have come up this month that we tell you at all about it. At the beginning of our trip to Peru and Chile last summer, we were flying with Bill Haddon from Lima to Tacna aboard Fawcett. Being an old hand at foreign travel, particularly in South America, we felt obliged to explain some of the special features of travel in Latin America and the niceties of etiquette in particular and were so engaged when the plane landed at the airport. We led the way briskly into the terminal, expecting at any moment to have a representative of Southern Peru Copper pop up and present himself. However, this didn&apos;t happen so we repaired to the baggage arrival station to wait. All the bags were quickly picked up, but ours were no where to be seen. Bill was slightly agitated because the plane was being buttoned up for take off. However, rising to the emergency with our usual aplomb, we took charge of the situation. Brandishing the claim checks under the nose of the porter who pointed to them and said, "si, Tacna," we nodded briskly and in our serviceable Spanish said "si se[n]or, vayase viejo, rapido." He was off and back with our suitcases quickly enough.

Jan 1, 1970

Following is the personnel of the various society and national committees on which the A I M E is officially represented United Engineering Society Officers of the Board, 1920 JOHN VIPOND DAVIES,, President CALVERT TOWNLEY, 1st Vice-president ALFRED D FLINN,, Secretary WALTER M McFARLAND, 2d Vice-president JOSEPH STRUTHERS, Treasurer Finance Committee House Committee WALTER M McFARLAND Chairman GEORGE H PEGRAM W L SAUNDERS

Jan 1, 1923

PROF RICHARD ÅKERMAN Stockholm, Sweden ANDREW CARNEGIR New York, N.Y. DR. JAMES DOUGLAS New York, N.Y. PROF HATON DE LA GOUPILLIERE Paris, France R.A. HADFIELD Sheffield England PROF HANS HOEFER Leoben, Austria PROF HENRI LOUIS LE CHATELIER Paris France M FLORIS OSMOND Paris, France JOHN E. STEAD Middlesborugh, England PROF DIMITRY CONSTANTIN TSCHERNOFF St Petersburg, Russia CHARLES D WALCOT Washingtion D.C. PROF DR HERMANN WEDDING Berlin, Germany

Jan 1, 1910

By C. J. Hicks

The labor policy of the Standard Oil Co. (New Jersey) is founded first of all on paying at least the prevailing scale of wages for similar work in the community; on the eight-hour day at the refinery, with time and one-half for overtime; one day&apos;s rest in seven; sanitary and up-to-date working conditions; just treatment assured each employee; opportunity for training and advancement; payment of accident benefits beyond the amount prescribed by the State compensation law; health supervision by a competent medical staff; payment of sickness benefits after one year&apos;s service; coöperation with employees in promoting thrift and better social and housing. conditions; and assurance of a generous annuity at the age of 65, guaranteed for life after 20 years of service. Most of these features have been a part of the company&apos;s policy for many years, but it is only during the past two years that the cooperation of employees in determining these matters has been definitely assured through industrial representation. Industrial representation, in the Standard Oil Co. (N. J.), is a principle rather than a procedure. It is built upon the belief that personal association of those interested in any problem leads to a mutual understanding and a fair decision as to what is right. Fully believing in this principle, representatives of employees and representatives of management evolved a simple plan, the basis of which is that it gives every individual employee representation at joint conferences on problems and fundamental principles affecting all those interested in the industry. It is based on cooperation, not antagonism; its operation makes perfectly clear both to management and to employees that their interests are identical, and not at variance with the interests of the stockholders, and that mutual understanding and cooperation insure progress and success for all. Furthermore, experience has definitely shown that representatives of the employees are not only alert for the employees&apos; interests but are as keen as the representatives of the management in determining and insisting upon fairness to the employer. Though the plan has been in operation nearly two years, it is an experiment, in that, being based on a principle rather than on cut-and-

Jan 1, 1921

By Charles H. Addison, Robert W. Shields, James W. Sweeney

GIPSY: Is user oriented. Is flexible in applications. Is an ITERATIVE question answering system. Has an adaptable retrieval mechanism. Has both a batch and a teleprocessing version. Allows the user to "browse" through his information. Has ability to answer "ad hoc" queries. Is a currently working and proven system.

Jan 1, 1969

By Riki Kobayashi, Donald L. Katz

The dew point of natural gas which has been in equilibrium with gas hydrates has been reported to be lower than that obtained for natural gas in equilibrium with water1,? Hammerschmidt&apos; reports a lowering of the dew point of 13 F for a natural gas in equilibrium with hydrate at 380 F and 525 psi. Records and Seely2 likewise show that the dew point of gas leaving hydrate separators&apos; is as much as 150 F below the separator temperature. This paper presents the reasons for the observed differences between the equilibrium temperatures and the dew point temperatures. Descriptions of the dew point determination by the Bureau of Mines and ASTM tester3 indicate that the dew point is taken as the temperature at which liquid water droplets first begin to appear on the cooled mirror surface even though the temperatures involved are below that required for the formation of gas hydrates or ice. PRESSURE-TEMPERATURE DIAGRAM FOR METHANE-WATEK SYSTEM Fig. 1 presents a schematic pressure-temperature diagram for the methane-water system" for some constant pressure between the critical pressures of pure methane and pure water i.e., pressures frequently encountered in pipeline operations. The possible equilibrium relations are shown by the heavy solid lines. Curve AE represents the saturated water content or dew point of gas in equilibrium with a water-rich liquid solution while curve EF represents the dew point of gas in equilibrium with hydrates. In addition the dotted line DE labelled "metastable dew point" is introduced to explain the apparent discrepancy betwceen the dew point determination and gas-hydrate equilibria. Thermodynamics place certain restrictions on the location of line DE6, namely, that (1) the concentration of water along the line DE be greater than the concentration of water along EF or that the metastable line split the angle formed by the intersection of line GE and EF

Jan 1, 1956

By R. M. Hudson, P. E. Perry

Weight-gain data obtained by nitriding low-carbon sheet steel in an amrnonia CNH,) atmosphere indicated that the process obeyed a parabolic rate law. The calculated actization energy for nitriding in the range 964" to 1268°F agreed reasonably well with published data. At 1358"F, rate data indicated that the activation energy decreased. Weight-gain data obtained by uszng mixtures of NH3 -Nz at 1268°F containzng jrom 10 to 100 zol pct NH3 also obeyed a parabolic rate law. The rate of &apos;nitriding increased with an increase in the NH3 content of the gas Mixture. It is well-known that steel heated in gas mixtures containing ammonia (NH3) takes up much larger quantities of nitrogen than steel heated in nitrogen, both gases having a total pressure of 1 atm;&apos; this phenomenon can presumably be attributed to the catalytic decomposition of NH3 on the steel surface to furnish nascent (monatomic) nitrogen. This process was studied bv Brunauer. Jefferson, Emmett, and Hend-ricks at furnace temperatures of 752" and 831°F2 using mixtures of NH3 in Hz. Englehardt and wagner3 reported that, at a furnace temperature of 914°F and under their experimental conditions, both nitriding and denitriding were controlled by the rate of gas-metal reactions at a steel surface rather than by the rate of diffusion of nitrogen in iron. The present study was undertaken to obtain information on the kinetics of nitriding low-carbon steel strip at higher temperatures so that practical rates for short-time strip-annealing treatments could be estimated. Variables studied included time: temperature, and NH, content in the annealing atmosphere. Mechanical and chemical characteristics of steel nitrided in this manner will not be considered in the present article. MATERIALS AND EXPERIMENTAL WORK The samples used were from a commercial low-carbon steel, 0.0244 cm thick, in the cold-reduced condition. The chemical composition of this steel is given in Table I. Panels were cut to 5.1 by 17.8 cm, degreased in toluene, and weighed just before treatment. Four specimens were nitrided under each of the experimental conditions. A study was made of the nitriding rate of steel in a 100 vol pct ammonia atmosphere, 740 mm pressure, at five specific temperatures within the range 964" to 1358°F. The nitriding rates of steel in ammonia-nitrogen gas mixtures containing 10, 18, 26, 50, and 100 vol pct ammonia, 740 mm total pressure, at 1268°F were also determined. All atmospheres used were dried by successively passing them through drying towers packed with soda lime and with Linde Molecular sieve Type 4A. Quoted gas compositions refer to those entering the furnace. Specimens were held in the constant-temperature zone of a vertical annealing tube furnace for times of 14, 3, 5, 10, or 15 min. Gas flow rates were maintained at 3.8 cu ft per hr, which was nineteen volume changes per hour for the system used. The rate of flow was selected to provide a high level of free NH3 for cracking on the steel surface where the ammonia gas is most effectively used as a nitriding agent. The vertical annealing tube furnace consisted of a Hevi-Duty tube furnace with a 2 1/2-in.-ID mullite ceramic high-temperature tube. The constant-temperature zone (controlled within 10°F) was about 10 in. long. After each specimen was degreased, a hole was punched in one end, for attaching the specimen by hook to a chain so that it could be lowered into or raised from the high-temperature portion of the tube by means of a power-driven winch. A stainless-steel access port with O-ring seals was connected by suitable glass-to-metal seals to the cool upper portion of the furnace tube. After the weighed specimen was placed in the access port, the furnace tube was evacuated to approximately 10"3 torr, and then the system was flushed thoroughly with the atmosphere under study. When the gas flow rate and constant-temperature zone of the furnace were established, the specimen was lowered into the constant-temperature zone. The atmosphere flowed from the top to the bottom of the vertical furnace tube and was then vented. For all these runs, during the first 3 min of the time the specimen was in the constant-temperature zone of the furnace the specimen was heating up to the tempera-

Jan 1, 1970

By P. J. Dean

This Paper contains a comprehensive survey of the known electron-hole radiative recombination mechanisms in the family of III-V compounds. Because of space limitations, the luminescence properties of each III- V compound are not reviewed separately and exhaustively. Instead, the different known types of recombination processes are discussed in turn and exemplified with reference to the III- V compound in which they were first recognized, or are best understood. Electron-hole recombinations usually occur predominantly at impurities or lattice defects either introduced de1iberately or inadvertently present, but radiative intrinsic interband electron-hole recombinations, which occur in perfect crystals, have been observed. Recombination processes which involve the participation of impurities or lattice defects ("extrinsic" recombinations) considered include transitions in which a) free carriers recombine with carriers trapped at impurities ("free to bound" transitions) , b) electrons bound at donor impurities recombine with holes trapped at acceptor impurities ("donor-acceptor pair" recombinations), C) excitons bound to charged or neutral donor or acceptor impurities recombine radiatively (both "resonance" and "two-electron" "bound exci-ton" transitions have been observed), d) excitons bound to neutral donor or acceptor impurities recombine non-radiatively (an example of an "Auger" recombination), and e) excitons bound to impurities with the same number of valence electrons as the host atom which they replace ("isoelectronic " traps) recombine radiatively. In addition, Auger recombination processes involving one or more free carriers have been observed. These extrinsic processes all involve impurities which are present as point defects. Some apparently well-authenticated examples of the recombination of excitons bound to complex impurity-lattice defect centers including nearest-neighbor donor-acceptor pairs are also discussed. Identificalions of the transitions involved in stimulated emission from the direct gap III-V compounds are briefly reviewed. Although the examples of these recombination mechanisms are selected from the III-IV compounds ia this review, these processes have quite general relevance in semiconducting crystalline solids; irrdeed most of them have also been identified in the 11- VI compounds and elernental semzconductors. THE development of crystal growth and purification techniques in recent years and concurrent advances in the understanding of physical processes in solids has accelerated the development of a wide variety of solid-state electronic devices of proven utility. These de- vices are generally used for switching or amplifying operations in electrical circuits. Most solid-state circuit elements are very photosensitive. This photo-sensitivity is generally undesirable and the single-crystal chip forming the active portion of the solid-state device is mounted in an opaque container. The photosensitivity is made use of in phototransis-tors and photodiodes, which are among the most sensitive detectors of electromagnetic radiation particularly in the near infrared.&apos; In these devices, light is converted into electrical power. The solid-state lamp utilizes the inverse effect, namely the conversion of electrical power into light. There is an increasing tendency to use single-crystal diodes rather than the earlier electroluminescent cells in which the active material is present as a powder embedded in a suitable dielectric.&apos; The radiation is emitted at a rate far in excess of the thermal equilibrium rate for the frequencies and temperatures involved; i.e., luminescence occurs. The development of practically efficient solid-state lamps is at an early stage compared with solid- state circuit elements or even photodetectors. Considerable progress has been made in recent years, however.3 The present review is devoted to a survey of the radiative recombination processes in the semiconducting compound crystalline solids formed from elements in groups I11 and V in the periodic table. These materials exhibit the full range of known recombination processes in solids. In fact many of these processes were discovered in 111-V semiconductors. Nonradiative recombination processes, which control the lutninescence efficiency, are also discussed. Luminescence is efficiently excited in semiconductors through processes which produce large excess concentrations of free electrons and holes in the energy bands of the crystal. Transitions induced by lattice defects or impurities usually predominate in the recombination process. By contrast, luminescence in the conventional fluorescent lamp is excited by optical absorption at the luminescent impurity center itself (the activator) and/or at a second type of impurity center (the sensitizer). This latter type of photoluminescence process, occurring in doped ionic crystals with wide band gaps, is outside the scope of this review.4 I) ENERGY BAND DESCRIPTION OF ELECTRON STATES IN CRYSTALS The energy band description of the energy states available to an electron in a crystal forms the basis of our understanding of the empirical division of crystalline solids into metals, semiconductors, and insulators in accordance with their electrical and optical properties.&apos; Nonmetallic crystals have a finite energy gap between the highest energy band which is

Jan 1, 1969