Search Documents

By Y. Ide, K. Kishitake

It is expected that an Al-Cr-N composite nitride film may have a higher resistance to oxidation at elevated temperatures than the well-known Ti-Al-N films. The formation conditions of Al-Cr-N films by a de reactive sputtering method and their properties were studied in this study. The films characterized with respect to their high temperature properties such as chemical composition, crystal structure, microhardness, wear and· friction. The crystal structure of the Al-Cr-N films changed from hexagonal phase to cubic phase with an increase in Cr content in the films. The resistivity to thermal oxidation of the Al-Cr-N films is superior to that of usual TI-Al-N films. A half of the friction coefficient in the Al-Cr-N film was obtained comparing with that in the ordinary TI-Al-N film at room temperature and the wear rate of Al-Cr-N film was 2 order smaller than that of TI-Al-N film. The Al-Cr-N films show a small friction coefficient at 500°C and then they are recognized to have good tribological characteristics.

Jan 1, 2000

By N. G. Azeredo

This work dealt with the evaluation of engineering structural clay brick samples that were sintered at estimated temperatures of 700 and 800°C. They were collected in a red-brick plant in Campos dos Goytacazes, RJ, Brazil. From a lot, a sample already sintered in its kiln at 700°C were collected and also a sample from the same lot only dried by the air, which were then sintered at 800°C controlled temperature. The samples were subjected to Brazilian Standard tests (ABNT NBR 15270:2005) to determine their geometric, physical and mechanical properties. In order to be classified as structural clay brick it is required minimum 3.0 MPa for the characteristic compressive strength (fbk) to be suitable for up to five floors structural building applications. We also used the Weibull Probability Plot and Weibull Maximum Likelihood Estimation to evaluate distribution parameters in order to compare the results of compressive strength obtained in the tests.

Jan 1, 2015

By Fernando Castro

Electric furnace steelmaking dust is a polluting residue that needs to be treated in order to recover metals contained and to produce an environmentally acceptable residue. Some hydrometallurgical approaches for its treatment have been evaluated, namely: caustic soda leaching followed by electrolytic recovery of zinc, ammonia leaching followed by zinc compounds precipitation and acetic acid leaching followed by lead, zinc hydroxide and gypsum precipitation.

Jan 1, 1992

By Mao Chen, Baojun Zhao, Zhixiang Cui, Leonel Contreras, Chuanbing Wei

Bottom blown oxygen copper smelting process developed at Dongying Fangyuan Nonferrous Metals shows many advantages such as flexible feed requirement, high productivity, low energy consumption and high direct copper recovery. However, the weak acid generated during the process is not stable which influences the waste management and continuous operation. The amount of the weak acid is determined by SO3 formed in copper smelting process. SO3 can be formed inside copper smelting furnace and boiler at different conditions. Effects of temperature and oxygen partial pressure on the formation of SO3 during copper smelting process have been discussed thermodynamically. Understanding of the mechanisms for SO3 formation will enable the operation of bottom blown copper smelting furnace to be optimized and generation of the weak acid in the process can be managed. The fundamentals developed in this study can also be applied to other copper smelting processes.

Jan 1, 2016

By Zhong Zheng, Xiaoqiang Gao, Zhaojun Xu, Shipeng Huang, Shenglong Jiang

Steel enterprises in China are trending to improve material and energy conversion effect, because they are facing great challenges including energy saving and emission reduction, quality and efficiency improvement. According to the theory of metallurgical process engineering, with the process data in steel manufacturing, some novel indices are designed for quantifying the conversions in different metallurgical unit processes. By analyzing common technologic characteristics in different units, the main manufacturing units are divided into two categories: metallurgical reaction unit and other manufacturing unit. The novel concepts named as “material dissipation rate of unit process”, “material accumulation rate of unit process”, “enthalpy change of unit process” and “energy dissipation rate of unit process” are proposed for describing the effect and dynamic characteristics of the conversions in manufacturing units. Finally, material dissipation rate and energy dissipation rate in unit processes are calculated and analyzed respectively with the real-world process data from a steel plant in China.

Mar 1, 2018

By Shadia J. Ikhmayies

SnO2:F/CdS:In bilayers were produced by the spray pyrolysis technique on glass substrates. The structures were characterized by recording and investigating their transmittance curves, I-V plots, X-ray difractograms (XRD) and by observing their scanning electron microscope (SEM) images. From the I-V plots it was found that the SnO2:F forms an ohmic or quasi-ohmic contact with CdS:In. XRD patterns show the polycrystalline nature of the films and show that there is a small shift in the position of the (200) line of SnO2:F without the appearance of new peaks. The morphology of the structures are compared with those of SnO2:F alone and CdS:In alone on glass substrates.

Jan 1, 2009

By T. Maruyama

Tamano Smelter of Hibi Kyodo Smelting Co., Ltd. has been operating with one Flash Furnace (FSFE) and three Peirce-Smith Converters since its start-up in 1972. Anode production capacity has increased from 101,000 to 263,000 t/y by the several expansion programs, while converter capacity has increased and stable operation has been established by several improvements as listed below. - Expanding the furnace body (length) - Development of two kinds of automatic scrap charging system for each converter. (Increasing the in-stack time and better control of the melt temperature) - Oxygen enrichment at slag blow and copper blow - Increasing the blowing rate This paper reports the details of these improvements.

Jan 1, 1998

By Jian Pan, Zhen He, Deqing Zhu, Shouyan Yue

"The differences of raw material characteristic among six kind of iron concentrates and the influences on ballability were studied from the aspect of the size distribution, specific surface area and particles morphology. The results show that the specific surface area of iron concentrates has crucial influence on ballability, and the effective method of improving ballability for weak ballability iron concentrate has been found. It is of important guidance for Chinese steel mills to import and use iron concentrate from the whole world.IntroductionChina's steel industry has developed rapidly in recent years, crude steel production in 2011 is an unprecedented 683 million tons, which is almost half of the world crude steel production, and it is equivalent to the total sum production of the nations which rank at 2,3,4,5 and 6 in the world [1]. In order to match the development of steel industry, the blast furnaces are becoming larger and more modernization, therefore charging burden of higher quality is requested, and the reasonable blast furnace burden structure is more and more important, at the same time, for iron ore powder sintering process's continuous improvement and development, another method providing ""concentrate"" for blast fumace-pelletizing is also taken seriously. The grate-kiln method of pelletizing has achieved great development for its unique advantage, and in just a few years, there are over 60 rotary kiln production lines have built or being built in China, the sum of pellets has reached to more than 140 million [2, 3]. The rapidly growth of pelletizing yield demands diverse source of pellet, which include not only domestic magnetite concentrate, but also imported hematite which is high in iron and low in silicon. Usually the ratio of imported hematite concentrate increased gradually. The imported hematite concentrate has high grade and fine particle size (the content of -0.074 mm mostly higher than 90%), but the ballability of part of the concentrates is poor."

Jan 1, 2013

By Mark Jolly, Nasim Soleimanian

"During the last 20 years CFD (Computational Fluid Dynamics) has been used as a tool to aid furnace designers and manufacturers to improve energy efficiency and effectiveness of glass furnaces. However as the models are maturing the effect of feeding equipment used to push the raw material into the furnace has not been included in the process models. This paper investigates the effects of batch pattern in the melt space caused by charging equipment on the energy efficiency of the furnace focusing on the melting zone. A simple batch patterns sensitivity study has been performed using purpose built software (Glass Furnace Model-GFM). It is concluded that in order to further reduce the energy consumption of the furnace it is necessary to model the batch charging process in more detail to find more opportunities for improvement.Introduction Glass manufacturing is a conservative industry which applies to all the four major segments (float glass, container glass, fiberglass, and specialty glasses). Risks due to the high capital investment, very long service life of the furnaces, and the demand for high performance and quality from the outset translates into evolutionary progress rather than revolutionary. The main problem facing glass manufacturers are the financial cost of manufacture, its impact on the environment, and mounting pressure imposed by the authorities for greener manufacturing and reduction in emissions.The main energy intensive activities involved in continuous glass manufacturing are: the need for high temperature to create and maintain the viscous flow, homogenisation of glass melt (melt residence time), and maintaining the two to achieve continuous output of glass at the right quality. The high temperature and long duration of homogenisation has resulted in the design oflarge furnaces, which have high energy consumption, low specific performance, and high C02 emissions. As an example in the container glass sector the most efficient furnace has a specific primary energy consumption of 3.8 GJ /tonne of glass at a level of 50% cullet in the batch. Even very small improvements in efficiency by optimising operation would have a high impact [1-14]. Given the conservative nature of the industry and the costs involved in experimental data gathering, CFD modeling of the process has been used extensively during last two decades to not only improve our understanding of the process but also as a tool in predicting possible optimisation windows, e.g. Glass Furnace Model ( GFM), a commercially available piece of software that has been developed to optimise furnace operation."

Jan 1, 2013

By A. N. Aposhian

The electronics industry generates tin/lead bearing by-products that can be recycled for their metal value. This paper will cover the processes used to recycle these tin/lead bearing byproducts from the plating, circuit-board fabrication and assembly industries. Though these processes are well known to the companies who do the recycling, few outside the industry including the generators of the by-products, understand the processes or needs of the industry. This paper will give a broad overview of these processes, and describe the services provided by this industry. The paper will also touch upon the future of the recycling industry, including the legislative and environmental push for the elimination of lead from electronics.

Jan 1, 2000

By Olli Hyvärinen

The capacity of Outokumpu Pori Copper Refinery has been increased by 50 % to 70 000 t/a in the last five years by adopting periodic current reversal, reducing spacing and installing some new cells in the old tank house building. Five years operation of PCR has proved that it is possible to achieve additional capacity with PCR and yet produce high quality cathodes. The impurity level in anodes has considerably increased, and recently, arsenic, antimony and sometimes bismuth have displaced nickel as the most critical impurity.

Jan 1, 1987

By Ibrahim Yusufoglu, Cem Kahruman, Sedat Ilhan, Ahmet Orkun Kalpakhi

"Scheelite is the main raw material in tungsten production. In hydrometallurgical processes, extraction of tungstate ions into solution is very important. During the leaching of scheelite in oxalic acid solutions, tungsten dissolves as a chelate complex. Scheelite includes impurities along with calcium tungstate. Determination of the dissolution of these impurities is important in the subsequent tungsten production stages. In this study, scheelite was dissolved in oxalic acid solutions and the dissolution of impurities was investigated. The quantities of dissolved impurities were determined by ICP - OES and characterization of the undissolved impurities in the leach residues was carried out by SEM - EDS analysisIntroductionScheelite and wolframite ores are used for the industrial production of tungsten. Both ores are dissolved in acidic or basic solutions, and ammonium paratungstate is obtained as an intermediate product. Prior to crystallisation of ammonium paratungstate, all the impurities must be removed. Among these, Fe, Si, P, Mn, Mg and Mo are classified as ""harmful"" elements and different methods are used for their removal [1]. During purification, solvent extraction, ion exchange, etc. methods are used.Potashnikov et al. [2] studied the dissolution of scheelite in acidic solutions and the effects of stirring speed, temperature and oxalic acid concentration on the dissolution kinetics.There are no works in the literature about the removal of impurities from scheelite ores in oxalic acid solutions. Therefore, the aim of this work was to investigate the dissolution mechanisms of impurities during the leaching of scheelite in oxalic acid solutions. The effects of temperature and oxalic acid concentration on the dissolution were also investigated. In addition, the characterization of the impurities which were not dissolved was studied."

Jan 1, 2012

By George Grandy

Kvaerner experience is being used to develop software to design or simulate crushing and screening plants. The model techniques discussed are presently being used for open-circuit plants and are being extended to closed circuit plants. The program contains a library of routines, each representing a piece of equipment or unit operation, which are assembled into one of several open-circuit plant configurations. Routines include gyratory primary crushers; standard secondary and shorthead tertiary cone crushers; single, double or triple deck screens; and stockpiles, feed bins and belt conveyors. The program uses steady-state models to simulate the performance of crushers and screens that have small residence times and quickly reach equilibrium when operating conditions and/or parameters are changed. The dynamic aspect of the total circuit model concerns the storage units within the circuit, i.e. stockpiles and bins, and, in the closed circuit configuration, circulating loads and size distributions. In many cases, just vendor's catalog data are necessary for a pre-feasibility simulation; in other cases, actual plant test data are required to obtain more accurate simulations. The entire plant is shown in a single graphic screen so the user can see all the relevant information he might want, and soft-keys are provided for the user to make on- line parameter changes and observe the effects on storage elements, equipment feed rates and the final product size distributions. The model also reports equipment utilization in percentage, power consumption, and other related operating information, and soon, will be able to report estimated capital and operating costs.

Jan 1, 1999

By P. C. A. Maia, J Alexandre, F. A. J. Saboya, A. R. G. Azevedo, G. C. Xavier

"This work shows the characterization of clay and the granite waste by-product from the sawing process of the granitic blocks, used as raw material for brick ceramic. Besides, shows the degradation of the ceramic material obtained with different by-product contents in the waste after lab test degradation, is investigated. The clay is obtained from mine use areas of ceramic industry in Campos-RI and the waste is originating from of the area of Cachoeiro-ES, an important center of decorative stone in Brazil. The mixes were made by the addition of 0% up to 10% of the waste in the raw material. After drying and firing up to 900°C, obtained prismatic pieces were considered intact. Physico-mechanical properties were obtained from wet and drying tests in laboratory considering 50 and 150 cycles. The results showed that the use of powder byproduct has a considerably influence on the weathering and strength of the material.IntroductionThe ornamental rocks and coating defines the most promising areas of business in the mineral sector [l]. In this context, the Espirito Santo appears as the main Brazilian state in production and export of ornamental rocks, representing 47% of national production [2] which in tum is one of the economic sectors most representative of this State, due of its transport logistics and port vocation that facilitates the export of such products.It is estimated that the state of Espirito Santo there are approximately 1,200 companies dedicated to the activities of ornamental rock by providing 20,000 direct jobs [ 1]. These mobilize support activities, such as companies that provide machinery, equipment and supplies for industries, including service providers for maintenance.However, the production of rocks produces about 15,000 tons of granite waste/month [3] only in the municipality of Cachoeiro ltapemirim-ES. This is justified by the presence of more than 500 extraction industries, cutting and processing of stone, with about 900 looms, waste generators.According to [4], there is great potential for the use of granite waste in red ceramics introduced for the manufacture of bricks, blocks structural ceramics. and other ceramic products, especially when evaluated on exposure to weathering."

Jan 1, 2014

By A. D. Zunkel

The zinc in electric arc furnace dust (EAFD) arises from the fuming and oxidation of the zinc present, mainly as galvanizing, in automotive scrap. The dust is collected from the electric furnace offgases in bag filters and is classified by the EPA as a hazardous waste (K061). As more zinc is used in galvanized sheet on automobiles and more automobile scrap is recycled via the EAF, the more zinc will be available for recovery and recycling. EAFD will become a more prevalent and important source of zinc compared to the traditional zinc sulfide concentrates ifit can be cost effectively processed.

Jan 1, 1995

By H. Hirayama, T. Okura, O. Kato

"Saganoseki Smelter & Refinery, one of the largest copper smelters in the world, has the annual capacity of 300,000 metric tons in copper content with two flash furnaces, six Pierce-Smith type converters, two anode furnaces, four acid plants, three tank houses and perfect pollution control system.Coping with the many severe conditions surrounding the copper industry in the last decade, Saganoseki Smelter has kept performing the stable operation, while enhancing the smelting capacity and developing new technologies such as the hydrometallurgical treating of converter dust recovered at electric precipitators. Especially in the operation of flash furnaces, which are of Nippon Mining's conversion type using hot air in a temperature of l,000ºC some technological improvements and complete operation control factors have approved the concentrate feed rate to reach to 2,200 tons a day for a flash furnace.Reported in this paper are the production control design for copper smelting process, and the operation control scheme of the flash furnace following the brief review of the characteristic of Saganoseki Smelter's process and some improvements. Copper Smelting ProcessDescriptions of major unit operations and general specifications of the copper smelting facilities are summarized in Table 1, and the present flowsheet of the copper smelting is described in Figure 1 (1,2).Outputs and raw materials treated in the last five years are shown in Table 2, in which concentrate includes powder copper scrap which amounts to 3 to 4% of concentrate.A full operation was performed for a period of one month, for both one flash furnace operation and for two flash furnace operation. With one furnace operation, 19,200 tons of copper were produced. With the two furnace operation, 84,000 tons of concentrates were charged and 33,500 tons of anode (net 28,600 tons of copper) were produced.The actual production level, however, has been kept at 80 to 90% of the full capacity because of low copper price, tight market of copper concentrate or fall of net demand in Japan."

Jan 1, 1989

By J. D. Sunderkötter, M. F. Stroosnijder, V. A. C. Haanappel

"TiAI-based intermetallic compounds have attracted considerable interest as structural materials for high-temperature applications due to their low density and substantial mechanical strength at high temperatures. However, one major drawback hindering industrial application arises from the insufficient oxidation resistance at temperatures beyond 700 °C. In the present contribution some general aspects of high temperature oxidation of TiAI-based intermetallics will be presented. This will be followed by a discussion of the influence of alloying elements, in particular niobium, and of the effect of nitrogen in the oxidizing environment on the high temperature oxidation behaviour of such materials.Extended AbstractIntroductionTiAI-based intermetallics are being considered as construction materials for high temperature components, e.g. in aircraft and car engines, due to their low density and substantial mechanical strength at high temperatures, see e.g. [1,2]. The best ductility can be attained with alloys consisting of y-TiAI with around 5-15 vol.% Q2-Ti3AI. However, one major hindrance to industrial application arises from the insufficient oxidation resistance at temperatures beyond 700 aG. In spite of their high aluminium content, TiAI-based intermetallics do not generally form long-lasting protective alumina scales. After longer exposure times the scales, which are initially rich in alumina, deteriorate and scales consisting of mixed alumina and titania predominate, with high growth rates similar to pure titania.It is not the intention of the present paper to present a general overview of the high temperature oxidation behaviour of TiAI based intermetallics, for which the reader is referred to the literature [3,4]. In the present contribution some general aspects of high temperature oxidation of TiAI-based intermetallics will be presented. This will be followed by a discussion of the influence of alloying elements, in particular niobium. The effect of nitrogen in the oxidizing environment on the high temperature oxidation behaviour of these intermetallics will also be considered."

Jan 1, 1996

By Lijun Liu, Yingwei Li, Jianhua Liu, Jinhui Peng

"As essential equipment in the metallurgical industry, current air heat exchangers cannot meet the requirements of high temperature heat transfer. In this paper, an energy efficient air heat exchanger, based on accumulation of the heat generated by microwave absorbing materials, is presented according to heat transfer theory and principles of the microwave field. A tubular shaped heat exchanger was designed and built up through temperature-rising curve, and experimental research of microwave high-temperature air heat exchangers was carried out. It was found from experiments that the tubular shaped heat exchanger fabricated using material B could be used for high temperature heat transfer system, and equilibrium temperatures could reach up to 457—485?.IntroductionHeating or cooling of air by heat exchangers is commonly practiced in a wide range of industries including construction, chemical, machinery, textile, printing, and dyeing [1-3]. Generally such heating or cooling of air is achieved in pipe heat exchangers. There are several drawbacks for such heat exchangers, namely, (i) the limitation of temperature to which the pipes can be heated, (ii) tendency to oxidize at high temperature, and (iii) poor strength of metallic pipes at high temperature. These limitations do not allow pipe heat exchangers to be operated at high temperatures [4-6].Microwave heating of inert solids, which are stable at high temperature, is a possible solution to achieve high temperature of the medium in air heat exchangers. It is well-known that microwave heating is an efficient, clean, safe, easy-to-control heating method. Microwave heating utilizes the dielectric and magnetic properties of a material. When microwaves penetrate and spread into the dielectric material, electrons, ions, etc move in the internal electromagnetic field, while the elasticity of inertia and friction impede these movements. This results in a significant thermal effect, increasing the surface temperature rapidly [7-8]. This paper studies mainly design and experimental research of microwave high-temperature air heat exchanger."

Jan 1, 2011

By Felipe P. D. Lopes, Jr. dos Santos, Sergio N. Monteiro, Frederico M. Margem

"Continuous and aligned fiber composites provide the highest possible reinforcement for a polymeric matrix. In particular, the impact resistance is significantly increased in comparison with a low energy absorbed brittle polymer. For this reason, investigations have been carried out with both synthetic and natural fibers as a way to improve the toughness of polymeric composites. Among the natural fibers, ramie was not yet been studied for its reinforcement effect to make tougher polyester composites. Thus, the present work assesses the impact toughness of polyester composites incorporated with different amounts of ramie waste fibers.IntroductionIn most engineering and other technological areas, the use of materials associated with low energy processing conditions is gaining attention for the possible environmental benefits. This offered an incentive towards the substitution of natural renewable and biodegradable materials for the traditional energy intensive synthetic materials [1]. Natural fibers from both origins: animal, such as silk and wool, and vegetable, such as cotton and jute, are typical examples of those environmentally friendly materials. Low cost and highly reduced processing machinery wear are important advantages of the natural fibers over the most common synthetic ones such as glass fiber and nylon. For these reasons, polymeric composites reinforced with natural lignocellulosic fibers have nowadays been the subject of investigation [2,3].The mechanical strength is one important property of lignocellulosic composites to access the possibility of uses like structural materials for building parts such as doors and panels, as well as furniture. In this case, mechanically strong fibers like sisal, jute, curaua and ramie [4-7] are most convenient. Moreover, the relatively low fiber/matrix interfacial shear stress in these composites is associated with higher impact energy. In fact, a greater energy has to be expended for the rupture of a weak interface. The many cracks that are formed by impact tend to branch during the fiber pullout from the matrix [8]. A larger number of cracks correspond to a greater fracture surface and consequently higher toughness."

Jan 1, 2008

By Józef Czernecki

Chalcocite-bornite concentrates of KGHM contain, similarly to chalcopyrite concentrates, 20-30 wt.% Cu but several times less iron (2-7 wt.%) and sulphur (9-12 wt.%). Another useful characteristic of KGHM concentrates is the presence of organic carbon (5.5-8.5 wt.%) in them, which serves as fuel in the flash smelting process. The main contaminants of the concentrates are lead (1.3-2.5 wt.%) and arsenic (0.05-0.4 wt.%) which require appropriate technological treatment in order to remove them from the copper pro-duct. Chalcocite-bornite concentrates are processed in KGHM by two different processes: ? a flash smelting process (Glogow 2 Smelter) ? a shaft smelting process (Glogow 1 Smelter, Legnica Smelter) The shaft smelting process used in the Glogow 1 Smelter and in the Legnica Smelter has higher production costs than the flash smelting process of HM Glogow 2. Additionally, the shaft smelting process employs several concurrently running installations (six dryers, seven briquetting lines, six shaft furnaces, nine converters), the operation of which, including maintenance, requires significant financial expenditure. Therefore, the Company is currently considering the substitution of the shaft furnace process in the Glogow 1 Smelter and in the Legnica Smelter by the one stage flash smelting process located in the Glogow Smelter, with output equaling the copper production capacity of both smelters, i.e. 320 000 ? 350 000 t/a. There are two technological options being considered which differ from each other in their man-ner of flash slag cleaning. In the first, the slag cleaning would be the same as in the existing Glogow 2 Smelter, i.e. the slag would be cleaned by pyrometallurgical reduction of the oxide copper and other metal compounds in the electric furnace in order to produce waste slag containing below 0.6 wt.% Cu. However, the other option of the flash slag cleaning would be carried out in two stages. After preliminary slag reduction in the electric furnace to 3-5 wt.% Cu, there would be flotation of the partially reduced slag.

Jan 1, 2006