Search Documents

By E. W. Murbach

The oxidation of uranium carbide by oxygen at various pressures, and by air, has been investigated at temperatures up to 600°C. Arc-melted and cast uranium carbide displays oxidation behavior that appears to be dependent on its treatment after melting. ccReactive" uranium carbide, which results from exposure of freshly melted material to laboratory air, ignites in oxygen at about 275° to 350°C depending on pressure, and in air at about 350°C. The product of the initial oxidation appears to be UO2+.. Continued heating produces U30,. The initial oxidation rate is poportional, roughly, to the square root of the oxygen pressure. The activation energy determined for the initial oxidation reaction is 7.1 kcal, from 400° to 600°C in 10 mm of oxygen. AN investigation of low-decontamination methods for reprocessing uranium carbide reactor fuels is being carried out at Atomics International. One of the reprocessing cycles includes oxidation of the fuel at relatively low temperature (300° to 500°C) and reaction of the product oxide with carbon at elevated temperatures (above 1500°C) to produce uranium carbide. A number of small-scale experiments have been carried out in which uranium carbide was oxidized in air and oxygen at various pressures to measure reaction rates and to obtain other information concerning the oxidation process. In initial experiments with arc-melted UC, ignition was observed at about 275°C in oxygen or 350°C in air. However, similar experiments by Neymark' at 426°C in air showed no ignition. It was soon determined that the difference in oxidation behavior was due to the treatment of the UC following arc-melting. Neymark's experiments were carried out with freshly melted UC while those reported in the

Jan 1, 1963

By NORMAN D. FitzGkrald

IN 1942 the outstanding characteristic of the petroleum industry was the multiplicity of war-induced distortions in virtually every segment of the business. So devastating was the success of the Nazi submarine campaign along the shores of the western Atlantic and on transoceanic routes that within six months after our entry into the war petroleum rationing was necessary in the East Coast area. The conquest of the Netherlands Indies by the Japanese three months after the opening of the war in the Pacific cut off our normal sources of rubber, and in our first year of war nationwide rationing of gasoline had to be invoked to conserve rubber-borne transportation facilities. Meanwhile the oil industry faced the imperative necessity for rapid expansion in the output of aviation gasoline and later accepted the vast responsibility for developing a new industry. synthetic rubber manufacture. Probably no other essentially peacetime industry has been forced to make so many complicated adjustments, yet its response to its wartime obligations has been nothing short of dramatic.

Jan 1, 1943

By E. L. Anders

The Mile Six pool is located on the La Brea-Parinas Cullcession of International Petroleum Co., Ltd., in northwestern Peru on the west coast of South America. The reservoir pressure in this pool has been maintained within 200 psi of its initial value throughout its history, and gravity drainage has played an important role in the production behavior. It has now produced 95 per cent of its estimated ultimate recovery. It is estimated that this interesting oil pool will ultimately produce 67 per cent of the initial oil in place and that the resulting residual oil saturation may be as low as 19 per cent of the pore volume (29 per cent of the hydrocarbon pore volume). An evaluation of reservoir rock and fluid characteristics and ultimate oil recovery is presented. INTRODUCTION This study of Mile Six pool was made to evaluate its performance according to latest available information. The production performance of this pool has been discussed in various articles in the past. and the reported behavior has been used as an example for application of computation procedures for gravity drainage depletion' and as an illustration of field behavior under gravity drainage or expanding gas cap drive. There have been wide variations in reported values of initial oil in place, reservoir oil volume factor. connate-water sauration, volume of effective sand, and ultimate recovery because of the paucity of reliable basic data. These various factors have been determined as accurately as practicable with the latest available information, and this evaluation is presented herein. The production history of Mile Six is an excellent example of gravity drainage depleion with effective pressure maintenance by gar injection. GENERAL Mile Six pool was discovered by cable-tool drilling in November. 1927. when well 1996 was completed in the Parinas sand. After slow development with cable tools and sporadic production. the pool was opened to continuous pro(iuction in November. 1933. and develpment was completed with rotary rigs. Pressure maintenance was started in December, 1933. by returning gas to upstructure wells. Most of the development was 'completed by 1937, but some additional wells were drilled in the period 1939-1947. and several old wells were deepened. A total of 46 oil and gas wells and 4 dry holes were drilled on approximately 7-acre spacing. Of the producers. 21 are now flowing. 2 are pumping. 44 are gas input wells. 3 are abandoned. I is a gas well shut in. and 15 are shut in because of non-commercial production or high gas-oil ratio. The locations of all wells are shown on the map of Fig. I. Total oil production on Dec. 31. 1952, was 30,867,373 bbl: cumulative gas production was 22,023,777 Mcf; and 26,410,946 Mcf of gas had been returned to the reservoir. These figures do not include oil and gas lost ill a blowout in January. 1940. GEOLOGICAL DESCRIPTION Mile Six pool is located on the northern end of a structural spur projecting from the La Brea-Negritos uplift.' The spur is probably a reflection of a basement structure. It plunges gently to the north, i broken into a complex series of fault blocks. and contain.; the Verdun Alto. Section Sixteen. and Mile Six pools. The Parinas handstone (lower Eocene!. which is the producing formation in Mile Six. occurs at an average depth of 2,200 ft in the pool and dips north and east at from 15' to 20". The pool covers an area of approximately 350 acres. Mile Six is downfaulted about 600 ft from Section Sixteen pool to the soutb. and a major fault forms its western boundarv. The north and east boundaries are formed by the intersection of the sand top with the water-oil contact which occurs at approximately 2.440 ft subsea. An original gas-oil contact probably existed at about 1.875 ft subsea. Fig. 1 presents the latest structural interpretation of the pool. and Fig. 2 is an isopach map showing thickness of the total Parinas formation above the original water-oil contact. The heavy lints of Fig. 1 are contours on the sand top, and the fine lines are contours on the fault planes. This type of straight-line structural map was developed 1)) International's geologists to reflect structural conditions where the bedding planes dip and have no curvature. 'The La Brea-Parinas Concession is highly faulted by normal fault.. The beds are flat wherever exposed. The Parinas formation is approximately 635 ft thick. and it is etimated that 62 percent II the formation is effective sand. The original oil zone was about 565 ft thick. Fig. 211 presents an electric log showing typical Parinas sand development ill Mile Six pool. The Parinas band in Mile Six i. a well-sorted. medium- to-coal-se-grained. cross-bedded sand with minor lenses of shale and small lenses and pockets of pebble conglomerate. The sand grains are subangular to rounded and consist chiefly of quartz with feldspars. biotite hornblende, and augite as accessory minerals. Because of faulting of the Parinas- formation to the east and north of the pool. there is probably l possibility of a significant, natural water drive in Mile six. The faults within the pool. as indicated in Figs. 1 and 2. are of smaller disI,laceInent and seem to act only , partial barriers to fluid movement within the reservoir. RESERVOIR CHARACTERISTICS Core analysis data are available from five wells. The data were obtained from three wells (Nos. 3401. 3586 and 3719) at the time of their completion and from well 1996 when the original liner was sidetracked and the well was deepened ill 1946. Data from well 2779 were obtained in 1943 from old cores taken when the well was deepened in 1934. From these core analyses. the average porosity was estimated to be 22.6 per cent. and the average permeability to dry ail. was estimated to be 780 and Measured productility indices varied from 3.1 to 71.4 B/D per psi differential. Specific productivity indices varied approximately from 0.1 to 0.3 B./D per psi per ft of sand.

Jan 1, 1953

By F. H. Wilson, R. M. Brick

With the papers of Palmer and Smith1 and of Burghoff and Bohlen,2 published in 1942, understanding of the problem of the development of ears on deep-drawn brass cups was brought to the point where, from a practical standpoint, producers of brass sheet could keep earing under control. However, these very practical results raised questions concerning the reasons for the observed behavior. Since plastic deformation is fundamentally a function of crystallographic slip, these reasons must be considered in the light of the textures to be found in the annealed sheet. Various attempts have been made. to interpret the mechanism of ear formation by correlation with the preferred orientation and the anisotropy of the sheet. However, none of these has satisfactorily explained why ears are usually found in the rolling and transverse directions for copper but at 45' to these directions for brass. This paper offers additional data on these two related subjects and has been divided into two sections The first section provides a survey of the recrystallization textures of brass as affected by annealing temperatures and prior reductions, and an account of the caring behavior which accompanies these textures. The second section reports new data on the anisotropy that accompanies a characteristic texture for brass and endeavors with partial success to establish the factors that account for the difference in earing behavior between copper and brass Earing BehavioR oF Brass Review of Textures The recrystallization texture of severely rolled brass was first reported by Bass and Glocker.3 The preferred orientation to which this texture, obtained from metal annealed at 500°C., was most akin was (II3)[I12] This texture has been confirmed by Bauer, von Göler and Sachs;4 Brick;' Brick, Martin and Angier;6 and Cook and Richards7 who, in general, used annealing temperatures under 500°C. Bass and Glocker3 also reported the recrystallization texture at 850°C. to be the same as at 500°C. They analyzed their textures by means of single photograms obtained with white radiation. The photo-grams for both temperatures are reproduced in their paper, and there is a strong similarity between the two. However, for the latter temperature, the number of spots registered on the film was remarkably large for the grain size to be expected, and the authors made no mention of using a technique that would integrate a large enough area of the specimen to produce so many spots. The only other attempt to determine textures resulting from high temperature

Jan 1, 1945

By E. N. Aqua, C. M. Owens

The microstructure in cold-rolled Zircaloy-4 sheet has been characterized by transmission electron microscopy and X-ray diffraction line-broadening techniques. The rate of work hardening is measured in terms of microstrains, particle sizes, micro hardness, the tensile yield strength. The tensile yield strength of Prestrained (less than 10 pet) Zircaloy-4 sheet is found to be a linear function of the square root of the dislocation density, us predicted by work-hardening theories. ZIRCALOY is one of the most important structural alloys for nuclear reactor applications.''2 In order to understand the effects of the nuclear environment on Zircaloy structural members, the preirradiation microstructure must be characterized. This report will describe the substructure existing in cold-rolled Zircaloy-4 sheet as observed by electron microscopy and by X-ray diffractometry. I) EXPERIMENTAL PROCEDURE Commercial Zircaloy-4 strip was cold-rolled and annealed in argon at 760°C for 1 hr. The annealed sheet was again cold-rolled to a maximum of 50 pct reduction in thickness with segments of the strip being retained after 2.5, 5, 10, and 20 pct reductions. One-inch-square portions were chemically polished (50 parts HNO3, 50 parts H2O, 10 parts HF) and mounted onto lucite blocks using double-sided tape to prevent bending during handling. Thin foils suitable for transmission electron microscopy were prepared from each of the sheet samples. The sheets were mechanically polished through 600-grit paper to a 3 to 4 mil thickness and were chemically polished by immersion for 1 to 2 min in a solution containing: 50 parts HNO3, 50 parts H2O, and 10 parts HF, and rinsed in distilled water. The final metallographic procedure was to electropolish for less than 10 sec with an electrolyte of 10 parts perchloric acid and 90 parts glacial acetic acid, at 20 v, at room temperature using stainless-steel point cathodes and a vigorous stirring action. These foils were examined in a Philips EM 200 electron microscope using a 100-kv accelerating voltage.

Jan 1, 1968

By R. G. Davies, R. H. Richman

Several techniques, X-ray diffraction, transmission electron microscopy, conventional, metallography, and mechanical property measurements are combined to investigate decomposition in the suPersaturated solid solution Fe-27 at. pct Be. The following sequence of structures for aging temperatures below 400°C is established: massive short-range order, pseudo-FeBe (L2o) order, Fe3Be (DU3) order, sinusoidal modulation of composition, general or continuous precipitation, and discontinuous or cellular precipitation. In addition to this sequence itself, several features of the individual stages are noteworthy; for example, when coherent modulations occur, their development is parallel to (100) everywhere in the specimen apparently without incubation, and both the wavelength and the composition amplitude of the modulations increase with aging time. Two types of discontinuous reaction are observed, depending upon the aging temperature. At low temperatures (<550°C) the boundary-nucleated variety of discontinuous precipitate predominates; but at higher temperatures (>600°C) the crystallographic variety occurs instead. Hardness and flow-stress measurements clearly reflect the quoted structure sequence. Some qualitative aspects of the structure changes and of the relationship between mechanical properties and structure are discussed. BERYLLIUM in solid solution markedly strengthens iron.&apos;" A recent study demonstrated that not only were supersaturated single crystals of Fe-27 at. pct Be very strong, but they deformed primarily by mechanical twinning.3 Such behavior, coupled with the decrease in solid solubility of beryllium in a Fe from about 33 at. pct at 1165°C to about 10 at. pct at 500°C4 as shown in Fig. 1, leads naturally to questions about property changes with aging in this system. In 1929 roll,1 and later Seljesater and Rogers,5 reported that useful increases in strength could be obtained by aging quenched Fe-Be alloys, but it was not until quite recently that any of the details of precipitation in these alloys were studied. Richman6 observed that both an Fe3Be superlattice (with a DO3 crystal structure the same as Fe3A1, illustrated in Fig. 2) and a modulated structure preceded the appearance of a discrete second phase in the 20 at. pct Be composition. Here, a modulated structure refers to a periodic composition fluctuation within one crystal, while its lattice remains coherent. Subsequent work on a Fe-Be alloys by Heubner7 and von Heimendahl and Heubner8 confirmed the existence of the modulated structure, although only an FeBe (L20) ordered structure was detected (also shown in Fig. 2). Both Rich-man and Heubner corroborated the large increases in hardness during aging reported earlier, but other mechanical properties were not examined. Since modulated systems are encountered relatively infrequently, the influence of coherent modulation upon mechanical properties is not well-known. With the accumulation of information about age-hardening systems, it has become clear that many precipitation reactions cannot always be described by the concept of heterogeneous nucleation at some lattice discontinuity followed by diffusional growth. Rather, complex sequences involving prior "preparation" of the matrix are quite common; that is, a transition structure occurs in the parent phase, instead of in some "nucleus" form. Delineation of such subtle sequences appears to be a worthwhile step toward the understanding of solid-state precipitation. Since not many structural progressions of comparable nature have been reported, the objectives of the present survey are to identify and elucidate the various

Jan 1, 1967

By Royal Jackman

Two comprehensive papers have appeared regarding the forms of copper that occur in smelter slags, one by Frank E. Lathe1 and the other by C. G. Maier and G. D. Van Arsdale.2 These authors comment on other published results and draw conclusions from their own investiga-tions. The development of X-ray examination of minerals and improve-ment in high-power microscopic methods make it possible today to get additional evidence by means that were not available to earlier investi-gators. The present work was confined to reverberatory slags obtained from five different plants. Some definite conclusions were reached regarding the forms of copper present in these slags. In most cases these agree with some of the findings of Maier and Van Arsdale but new methods of attack were used in the investigation.

Jan 1, 1933

By Samuel S. Wyer

Bethlehem Meeting, February, 1906 THE following abbreviations have been used in the text:¬ Am. MF. and Iron World. American Manufacturer and Iron World, Pittsburg, Pa. Can. Min. Rev. Canadian Mining Review, Ottawa, Can. Cass. Mag. Cassier&apos;s Magazine, New York, N. Y. Col. Eng. Colliery Engineer, London, Eng. Col. Guard. Colliery Guardian, London, Eng. Eng. and Min. Jour. Engineering and Mining Journal, New York, N. Y. Eng. News. Engineering News, New York, N. Y. Engr. Engineering, London, Eng. J. I. and S. I. Journal of the Iron and Steel Institute, Lon¬don, Eng. Jour. W Soc. of Engrs. Journal Western Society of Engineers, Chicago, Ill. Lond. Eng. The Engineer, London, Eng. Mines and Min. Mines and Minerals, Scranton, Pa. North of Eng. I. M. E. North of England Institute of Mining Engineers, Newcastle-on-Tyne, England. Oester Zeitsch f. Berg u. Hüt. Oesterrcichische Zeitschrift für Berg. und Hüttenwescn, Vienna, Austria. Pract. Engr. Practical Engineer, London, Eng. Proc. I. C. E. Proceedings Institution of Civil Engineers, London, Eng. Trans. A. I. M. E. Transactions American Institute of Mining Engineers, New York, N. Y. Trans. A. S. M. E. Transactions American Society Mechanical Engineers, New York, N Y Trans. Fed. I. M E. Transactions Federated Institute Mining Engineers, Newcastle-on-Tyne, England. Trans. I M E Transactions Institute Mining Engineers, Newcastle-on-Tyne, England.

Mar 1, 1906

By R. D. Mollison, C. F. Fogarty

Sulfur is widely distributed in nature. It is present in the earth&apos;s crust, the ocean, the meteorites that come to us from cosmic space and in practically all animal and plant life. According to Clarke,9 the earth&apos;s crust contains 0.06 pct sulfur. Large quantities of free or combined sulfur are found in coal, natural gas and petroleum. Mineral waters contain sulfates and hydrogen sulfide. Sulfur is rather plentiful in the crust of the earth; however, only under special circumstances can it be produced profitably. Sulfur is one of the cheapest raw materials used by industry; and, therefore, the economic feasibility of a given deposit is strongly dictated by the law of supply and demand on local as well as world-wide levels. The forms which are commercially important are elemental sulfur or brimstone, and the sulfides such as pyrite (FeS2), pyrrhotite (FenSn+1), chalcocite (Cu2S), sphalerite (ZnS), and galena (PbS); the sulfates such as gypsum (CaSO4,2H2O), anhydrite (CaSO4), and kieserite (MgSO4,H2O). Elemental Sulfur Elemental sulfur is found in many localities, generally in solfataras and gypsum type deposits. The solfatara deposits are found commonly in the neighborhood of active or extinct volcanoes as in Italy, Japan and Chile, or fumaroles associated with mineral springs such as the Mammoth Hot Springs in Yellowstone Park. Here the sulfur is deposited in tufas or other porous host rocks. This type of sulfur deposit probably results from the oxidation of hydrogen sulfide or the reaction of hydrogen sulfide with sulfur dioxide. Most of the world&apos;s supply of elemental sulfur comes from the gypsum-type deposits. Here the mineral occurs as either crystalline or amorphous sulfur in sedimentary rocks in close association with gypsum and limestone. This association is characteristic and occurs in almost all the great gypsum beds of the world, although sulfur is not always present in quantities of economic importance. Various theories have been advanced to account for this association. Bischof5 suggested that the sulfur came from hydrogen sulfide which resulted from the reduction of calcium sulfate by carbon or methane in accordance with the following reactions: CaSO4 + 2C= CaS + 2CO2 CaS + C02+ H2O = CaCO3 + H2S CaSO4 + CH4= CaS + C02+ 2H20 2H2S + 02= 2H20 + 2S All of the sulfur-bearing domes on the Gulf Coast have calcium sulfate in great quantity in the cap. They all show the presence of hydrocarbons. The oxygen for the final reaction could have been supplied by circulating ground waters. The principal objection to this theory is that temperatures of 700° to 1000°C are needed to reduce the sulfate to sulfide with carbon compounds. The geologic evidence is that the temperature of the sulfur-bearing domes of Texas did not exceed 100°C. Proponents of the theory say that geologic time or a catalyst replaced temperature. According to another theory the sulfur in the salt domes is the result of bacterial action. Sulfate reducing bacteria have been detected in sulfur cores and in the formation water issuing from salt domes. It has, therefore, been suggested that these bacteria converted the sulfate to sulfide which subsequently was converted to elemental sulfur.

Jan 1, 1960

By Elliot Rexford

The quality of aggregate materials is of major importance in governing durability and permanence of concrete structures. The problem of selecting suitable aggregate materials is two-fold. Geological factors include the type and character of the aggregate source, presence of known or suspected reactive constituents, and presence of thermally incompatible materials. Laboratory investigations include petrographic studies, soundness and reactivity tests, and tests of thermal properties. The importance of each factor in the selection of satisfactory aggregate material is considered in detail.

Jan 3, 1950

By C. W. Spencer, Che-Yu Li, R. J. Knight

The usual reaction product for the monotectic reaction in the Bi-Se system consists of rod -shaped particles of selenium-rich liquid embedded in a single crystal matrix of At certain crystallo-graphic orientations of the matrix with respect to the reaction interface, more complex shapes are as -sumed by the liquid particles. This reaction has been examined at different growth rates and relative crystallographic orientations of the matrix with respect to the reaction interface. The uhriation in auerage particle size of the liquid phase with reaction rate has been determined at one crystallograpIzic orientation of the matrix. On a plot of logarithm of average particle diameter vs logarithm of reaction rate, data points for crystals grown at rates of 10- to 1.0 cm per hr fall near a curve of slobe -0.4. MONOTECTIC reactions in binary alloy systems are reactions of the eutectic class in which, as the system is cooled through the three-phase reaction isotherm, one liquid phase (L) decomposes to a solid phase and another liquid phase (LII).&apos; A partial phase diagram, as taken from Hansen, showing the monotectic reaction in the Bi-Se system is given in Fig. 1. This diagram specifies the monotectic point at 618°C and 72 at. pct Se, and the monotectic reaction products as the intermetallic Bi Se3 and a liquid (LII) which contains approximately 98 at. pct Se. At a lower temperature, 217°C, this liquid may undergo a eutectic reaction in which the reaction products are BizSe3 and crystalline selenium. However, under conditions of rapid cooling, or quenching, from above 217°C, this selenium-rich liquid may be partially retained to room temperature in an amorphous or glassy state. The intermetallic BizSe3 is rhombohedral, of the space group jm;&apos; however, for convenience it is usually represented by a hexagonal struture. A pronounced plane of cleavage, which lies perpendicular to the main axis of the rhombohedral unit cell or parallel to the basal plane of the hexagonal cell, exists in the structure. The usual monotectic reaction product consists of rod-like particles of LII embedded in a single-crystal matrix of BizSe3, although at certain crystallographic orientations of the matrix BizSe3 other more complex shapes are assumed by LII. A similar rod-like, or cylindrical, morphology for the carbide phase has been reported by westbrook7 in the a Cr-Crz3Ce eutectic structure. In this paper the morphological characteristics of the LII particles, as retained to room temperature, have been examined under conditions of varying growth rate and crystallographic orientation of the matrix BizSe3 with respect to the growth direction. EXPERIMENTAL PROCEDURE Alloy specimens corresponding to the monotectic composition, 72 at. pct, or 50 w pct Se, were prepared from 99.999 pct pure bismuth and selenium obtained from the American Smelting and Refining Co. The two elements, corresponding to a total specimen weight of approximately 30 g, were encapsulated in 13 mm OD Vycor tubing under a vacuum of 5 x X mm of Hg. The capsules were suspended on a fine platinum wire in a Bridgman-type furnace which exhibited a temperature gradient of

Jan 1, 1963

By W. W. Vaughn, R. H. Barnett, E. E. Wilson

Soon after the search for uranium ores on the Colorado Plateau began in earnest, thousands of feet of drill core ranging from 1 1/8 to 2 1/8 in. diam became available for study. Although significant advances had been made in the technique of quantitative gamma-ray borehole logging, instrumentation was in the development stage, and complete reliance could not be placed on gamma-ray logs alone to interpret quantitatively the meaning of radioactivity in a drillhole. A method that would be faster than chemical analysis and still give reproducible and reliable results for various drill core sizes was desirable to provide additional information on the enormous footage of drill core being accumulated. A solid phosphor scintillation drill core scanner was designed and constructed. Basically the instrument was developed to measure radiation from a drill core which would not be clearly recorded by a gamma-ray logger using a Geiger tube as the sensitive element. Such data would be beneficial in constructing isorad maps to delineate ore-bearing zones. A calibration in the range 0.01 to 0.1 pct eU.,O, was provided; above 0.1 pct eU3O8 gamma-ray logs were available and were being used to calculate grade and tonnage of ore reserves. The core scanner, however, has been used to estimate equivalent uranium content of ore-grade materials containing as much as 2.2 pct eU3O8 with an accuracy of ± 10 pct, the sample being in the form of a BX drill core. Actually, an apparent calibration of eU3O8 vs counts per unit time is a straight line with a slope that is a function of the sensitive element and the geometry of the counting assembly. A true calibration that will show the expected departure from a straight line is due principally to the random nature of the pulse from a radiation source and the nonlinearity of the electron circuitry. Design and Construction: Three methods of detecting radioactivity were considered and applied in developing the core scanner now in use: 1) the Geiger tube, 2) liquid scintillation phosphors, and 3) solid scintillation phosphors. The desired sensitivity and long-term drift characteristics needed for this operation could be attained only by using solid scintillation phosphors. All three methods are discussed. Before scintillation counters were common, nine beta-gamma sensitive Geiger tubes 7/8 in. diam by 12 in. long were used, arranged to surround the drill core with tube axes parallel to the axis of the core. This arrangement of Geiger tubes was en- closed in a lead shield 1 in. thick, and provision was made to slide a 6-ft length of drill core manually into the counting chamber, one foot at a time. A count for each segment was taken with a scaler while the core remained stationary. The equivalent uranium content of the different sections of drill core could then be estimated with the aid of a calibration curve of counts per unit time vs percent equivalent uranium (eU). In rare cases the effects of the radioactivity concentrated in small areas within the core introduced errors in the readings made with the Geiger tube arrangement owing to the geometry of the measurement. The variability of counting rate due to a localized concentration of radioactivity in a spot in the wall of a drill core is illustrated in Fig. 1. This effect and the inherent low efficiency of the Geiger tube were considered major disadvantages of this counting arrangement. When liquid scintillation phosphors became available the core scanner in Fig. 2 was constructed to make a more accurate measurement of the equivalent uranium content of a sample. This instrument contains about 4 liters of liquid phosphor in a stainless steel coaxial cylinder 1 ft long, with inner and outer walls 0.060 in. and 0.125 in. thick, respectively. Four end-window type photomulti-plier tube with cathodes of 2 in. diam, immersed in the solution at right angles to the axis of the core, were used to observe light flashes in the phosphor. The liquid phosphor offered equal sensitivity to radiation originating at any point in the enclosure and represented geometrically the optimum in design. However, providing a semi-permanent leak-proof seal between the glass envelope of the phototube and the metal walls of the container proved to be a serious problem in constructing the equipment. The most effective seals were especially machined O-rings from sections of large tygon tubing. The tygon took a permanent set owing to cold flow characteristics and in most cases sealed completely. The light absorption characteristics of the liquid phosphor changed gradually with time, and after one month the counting rate had decreased to half the original value. The most sensitive liquid phosphor tested proved to be a solution containing 4 g of 2.5-diphenyloxazole and 0.01 g of 2-(1-naphthy1)-5-phenyloxazole per liter of toluene. With fresh solution in the chamber and with all photomultiplier tubes operating in parallel, the counting rate contributed by any one of the four photomultiplier tubes was about 85 pct of the counting rate from a single tube operated individually. From these observations it was concluded that owing to coincident loss and light attenuation within the liquid phosphor, the apparent sensitivity could not have been materially increased by additional phototubes. However, this approach to core

Jan 1, 1960

By J. E. Hanlon, S. R. Butler, R. J. Wasilewski

The temperature, orientation, and strain-rate dependence of tensile flow in single-crystal NiA1 of equiatomic composition have been investigated up to 800°C. Compression tests at room temperature have also been carried out. Optical and replica electron microscopy and X-ray diffraction methods were used to investigate the slip mechanisms. NiAl exhibits {110)(001) slip and cube slip {l00)(010) was also observed. This results in very high strength of single crystals in cube orientation. The implications of this slip mode, with the resultant small number of possible slip systems and three mutually perpendicular slip vectors, are discussed. ThE CsCl structure compounds represent a class related to the bcc elements, but their behavior is affected by three additional variables: composition (within the stability range of the compound), extent of long-range order perfection, and bonding energy. Very little data are available on the effects of these variables on mechanical properties. Rachinger and ~ottrell&apos; suggested slip to occur along (111) in compounds of low ordering energy; in compounds of higher bond strength (>0.06 ev), they observed (110) (001) slip. As pointed out by copley,&apos; only three in- dependent slip systems are available in the latter case; hence general deformation is impossible. Brown3 carried out a theoretical calculation of the yield-point variation with the degree of long-range order in the CsCl structure, based on the assumption of superdislocations. More general approaches, based on considerations of superlattice dislocations and antiphase domain boundaries in ordered structures, were carried out by Flinn~ and by Vidoz and Brown.&apos; These, however, give no information on changes in the slip structure—if any—between the ordered and the disordered compounds. This aspect was investigated experimentally and theoretically by Stoloff and Davies&apos; and by Marcinkowski and chessin7 in FeCo. The latter workers proposed the deformation behavior of the ordered FeCo to be essentially the same as that in many other bcc metals. Investigations of polycrystalline A~M~&apos;-&apos;O indicate considerable variation in mechanical properties with composition and test temperature. The existence of {123)(111) slip was reported in AgMg.&apos;9&apos;9&apos;0 (The formation energy of this compound, presumed to be ordered at all temperatures below melting, is 4.38 cal per g-atom," i.e., 0.024 ev per bond.) The yield strength has been reported as relatively independent of temperature below 0.45 T, (where T, is the absolute melting temperature). Tensile deformation of single-crystal AgMg was also investigated by Kurf-man," who observed marked tendency to single glide on{112}(111) and {110)(111). From observations of slip lines in deformed poly-crystalline NiA1, Westbrook et a1.I3 suggested the

Jan 1, 1968

By AIME AIME

S ULFURIC acid made in the United States during the last four years has averaged approximately 7,000,000 tons of 50" B6 acid a year. This is double the production of the year 1913. About 66 per cent of the acid is made from sulfur, 16 per cent from pyrite, 13 per cent at copper, lead, and zinc smelters, and the remainder from miscellaneous sources it her the chamber process or the contact process, (at some plants both) is used. In 1923, the contact process accounted for nearly 30 per cent of all the sulfuric acid made in this country and since then it has been increasingly employed. It was first introduced here in 1898, and has always .proved less expensive than the chamber process for the manufacture of .acid of high concentration and purity, but the latter produces acid of low strength suitable for many industries.

Jan 1, 1929

By A. Gatti, R. L. Fullman

A very fine dispersion of aluminum oxide is produced by internal oxidation of solid-solution alloy of 0.14 pet A1 in Ag. The particle size of the aluminum oxide is approximntely 50 to 100A in radius. The yield strength of the alloy is increased markedly by internal oxidation. A further increase in strength is produced by cold working the internally oxidized alloy. Recrystallization is retarded by the finely dispessed aluminum oxide particles, so that the strength increase resulting from cold work is retained on annealing at temperatures 14 to about 700°C. MANY workers&apos;-3 in the past have studied various aspects of the internal oxidation of aluminum-silver alloys. This paper is an extension of these studies with emphasis placed on the effect of time and temperature of annealing on the strength of these alloys after oxidation and subsequent cold working. Two general conditions are necessary to internally oxidize an alloy. First, oxygen must diffuse through the base material more rapidly than does the addition; otherwise oxidation will take place as a surface layer. Secondly, the affinity of oxygen for the addition must be greater than for the base material. After internal oxidation of certain alloys takes place, a marked increase in hardness accompanied by higher yield stress and improved creep properties is noted, presumably as a result of the highly dispersed oxide within the base material. Meijering and Druyvesteyn1 also noted that the internally oxidized portion of a partly oxidized alloy failed to recrys-tallize under annealing conditions that led to coinplete recrystallization of the unoxidized part. EXPERIMENTAL-METHODS AND PROCEDURES Few alloys can be made to contain a second phase that is extremely stable at high temperatures. Silver plus aluminum in solid solution was chosen for these internal oxidation studies because of the high rate of oxygen diffusion through silver and the very stable nature of aluminum oxide. Two alloys were vacuum cast. The nominal compositions were: Alloy A—1 pct Al, balance Ag; Alloy B—0.1 pct Al, balance Ag. Chemical analysis, which does not distinguish between aluminum and aluminum oxide, showed the conlposition to be: Alloy A—1.6 pct Al, and Alloy B—0.14 pct Al. The ingots were machined for surface cleaning, swaged and drawn to 0.020-in. diam wire. A sample 20 ft long of the 0.020-in. dianl wire of each composition was annealed 24 hr at 800°C in pure dry hydrogen. Each wire was then cut into two equal pieces. Photomicrographs of the 0.14 pct A1 alloy are shown in Fig. 1, the annealed 0.020-in. wire at the left and the oxidized wire to the right. The oxidation treatment for the first set of data was 1000 hr at 800°C in air. After this treatment the 1 pct A1 proved to be brittle. It is assumed that high alunlinum oxide concentration at the grain boundaries was responsible. The 0.14 pct Al wire remained ductile and all further data were derived using this alloy. One-half of this wire, about 5 ft, plus 5 ft of as-homogenized wire, was then drawn cold to 0.005 in. diam. All tensile tests were conducted with an Instron Engineering Corp. tensile-testing machine, Model TT-B. Unless otherwise indicated, the tests were made at room temperature with a strain rate of 0.1 per min. All metallographic samples were etched with an aqueous solution of 2 pct each of CrO3 and H2SO4 . EXPERIMENTAL RESULTS AND DISCUSSION PARTICLE SIZE DETERMINATION A study was made of the particle size of the aluminum oxide produced in the samples of Ag + 0.14 pct Al, oxidized 1000 hr at 800°C. A cross section of the as-oxidized wire was mounted in bakelite, polished, and etched with an aqueous solution of 2 pct each of CrO3 and H2SO4. The specimen was then thoroughly cleaned by stripping successive coatings made by applying 10 pct nitrocellulose in amyl acetate. The final replica of the cross section was made by applying 2 pct nitrocellulose in amyl acetate. The replica was stripped, transferred to a copper screen, shadow cast with chromium at 10 deg and photographs taken using a Phillips Metallix electron microscope at an accelerating potential of 100 kv. A photograph of an etched sample of the as-oxidized material is shown in Fig. 2. We believe the pits in the photograph are places were A12O3 inclusions were sitting in the matrix. By inspection, it appears that the volume fraction ob-

Jan 1, 1960

By L. J. Howell, R. C. Sommer, H. H. Kellogg

WORK described herein was undertaken with the aim of determining some of the physical-chemical properties of electrolytes suitable for the electrodeposition of pure zirconium metal. In this paper the phase diagram, vapor pressure, and activities in the melt are considered. In a companion paper,&apos; the electrolytic conductivity of some of these melts is reported. The melts studied were mixtures of NaCl and/or KC1 with ZrC1,. Chloride melts were chosen for study because 1) if the electrolyte is to be useful for industrial electrodeposition of zirconium, the chlorides will be preferred to the relatively costly bromides and iodides; 2) fluoride melts were being studied in another laboratory (Horizons Inc., Cleveland); and 3) melts containing oxygen, in any form, are unsuitable for preparation of pure zirconium, because of the great affinity of this metal for oxygen. Unlike electrodeposition from aqueous solution, the fundamental behavior of fused-salt electrolysis is poorly understood. In most cases, such basic electrochemical information as the phase diagram of the melt system, activities in the melt, conductivity, the nature of the current-carrying ions, the equilibrium electrode potentials, and the overvoltage behavior of the electrodes is unknown to the researcher who would develop a new electrodeposition process employing a fused salt. This research project was designed to supply information about some of these basic physical-chemical properties so that an intelligent choice of electrolyte for electrodeposition studies could be made. Experimental The experimental difficulties-encountered in this work result from the properties of zirconium metal and ZrC1,. ZrC1, is a solid which sublimes at 334°C. It is rapidly hydrolyzed by moist air to HC1, ZrOCl,, and ZrO,. Unusual precautions were exercised in this work to prevent hydrolysis of ZrC1, and rigidly to exclude oxygen, nitrogen, hydrogen, and carbon from the melts under study. These elements are known to react with and contaminate zirconium metal. All melts were studied in vacuum systems, i.e., in the presence of ZrC1, vapor only. Transfer of ZrC1, to or from the melts was accomplished entirely by vacuum sublimation. In this way, neither the melts nor the ingredients thereof were permitted to

Jan 1, 1958

E. O?C. Acker Jinzoc Adachi Truman H. Aldrich Walter H. Aldridge Anson W. Allen John H. Allen William R. Appleby W. Lawrence Austin W. S. Ayres David Baker John Henry Banks Henry C. Banon Alonzo F. Bardwell Wm de L. Benedict Robert Bentley Andrew A Blair Walter M. Brodie Elwin F. Brown Fredrick Burbidge H.H. Burden Charles Butters

Jan 1, 1941

E. O?C. Acker Jinzoc Adachi Truman H. Aldrich Walter H. Aldridge Anson W. Allen John H. Allen William R. Appleby W. Lawrence Austin W. S. Ayres David Baker John Henry Banks Henry C. Banon Alonzo F. Bardwell Wm de L. Benedict Robert Bentley Andrew A Blair Walter M. Brodie Elwin F. Brown Fredrick Burbidge H.H. Burden Charles Butters

Jan 1, 1942

For. the year ending February, 1919 PRESIDENT SIDNEY J. JENNINGS NEW YORK, N. Y. PAST PRESIDENTS L. D. RICKETTS NEW YORK, N. Y. PHILIP N. MOORE, ST. LOUIS, M.O. FIRST VICE-PRESIDENT C. W. GOODALE, BUTTE, MONT. TREASURER GEORGE C. STONE, NEW YORK, N. Y. SECRETARY EMERITUS ROSSITER W. RAYMOND, NEW YORK, N.Y. SECRETARY BRADLEY STOUGHTON NEW YORK, N. Y.

Jan 8, 1918

By J. F. Butler

Boron nitride, BN, has been identified in boron low-carbon steels by means of light microscopy, electron microscopy and diffraction, and chemical analysis. This boron nitride is responsible for strain aging suppression in these steels through the removal of nitrogen from solution; however, small oxidizing potentials which result in deboronization In the austenitic temperature range also result in boron nitride decomposition and the subsequent occurrence of nitrogen strain aging. THE addition of boron to low-carbon steels is an effective means of eliminating the detrimental effects of strain aging;&apos;,&apos; however, the mechanism by which boron suppresses strain aging has not been established. In studying the effect of heat treatment on the strain aging of boron low-carbon steels, Butler3 found that no detectable nitrogen was present in the ferrite solid solution after various heat treatments even though the total nitrogen analyses of the steels were 0.003 pct N. Apparently the function of boron in suppressing strain aging is the removal of nitrogen from solution to form a relatively stable second phase. A clue to the identity of this phase was found by Speight4 who extracted from an aluminum-killed boron steel an acid insoluble residue which contained boron and nitrogen in proportions corresponding to the compound, BN. Shyne and Morgan5 found that the addition of nitrogen to a hardenable boron steel lowered its hardenability in a manner which suggest-d the presence of nucleating particles (presumably BN) even at high austenitizing temperatures. Although this indirect evidence for the presence of boron nitride in boron steels has been found, the compound was not identified metallographically as a separate phase in these steels. Because boron has an affinity for oxygen comparable to that of silicon,5 boron steels must be thoroughly killed with aluminum in order to prevent the reaction of boron with oxygen.7 The affinity of boron for oxygen also is demonstrated through the ease of deboronization of a boron steel in an oxidizing atmosphere. Digges, Irish, and Carwile8 found that a mixture of wet natural gas and air caused both deboronixation and decarburization of a boron steel at 1900°F. The boron content rose at the surface of the steel due to the formation of boron oxide. Shyne and Morgan9 encountered deboronization at much lower oxygen potentials; loss of boron occurred in steels treated at 1750o F under argon purified to 0.0014 pct 0, even though decarburization did not occur. Boron oxide, B2O3, is much more stable than the nitride, BN, as is indicated by the standard free energies of formation at 980oC: -235 kcal per mol of B2O3 (liquid) and -28 kcal per mol of BN (crystal). It is evident that the oxygen potential must be kept low in the presence of BN in order to prevent its decomposition and the subsequent formation of B2O3&apos; The purpose of the work described in this paper was to identify the nitride phase responsible for the removal of nitrogen from solution and to study its stability under oxidizing conditions. IDENTIFICATION OF BN In order to identify the phase containing boron and nitrogen, several alloys high in boron and nitrogen were made up in a small vacuum furnace. In alloys 3 and 4, Table I, electrolytic iron was used as a charge material. Boron additions were made in the form of 18 pct B ferro-boron after the iron was molten. In the case of alloy 3, the charge was solidified at this point; for alloy 4, nitrogen at 1 atm pressure was admitted over the melt before it was

Jan 1, 1962