Search Documents

By W. Klement

By quenching liquid alloys, single-phase solid solutions are obtained in the ranges 0 to 42.0 at. pct Co-Au and 0 to 15 and 75 to about 100 at. pet Co-Cu. Metastable solid solutions are also found in multiphase 42.0 to 49.0 and 69. 0 to about 100 at. pet Co-Au alloys. fie inability to achieve complete solid solubiliiies in Au-co and cu-co alloys is rationalized by a conszderation of the rate processes during cooling and solidification. Trends in lattice distortion and shifts in the compositions of the melting-point minima and critical points are discussed for the binary alloys of copper, silver, and gold with some of the transition metals of the first long period. By rapidly cooling alloys from the melt, a continuous series of metastable solid solutions can often be obtained for components of similar crystal structure which normally form eutectic systems.' The eutectic system Au-Co, Fig. 1, and the peritectic system Cu-Co, Fig. 2, were investigated in order to determine the extent of the metastable solid solutions attainable with the present technique.* EXPERIMENTAL PROCEDURES Most of the alloys were prepared by melting weighed quantities of the elements (purity greater than 99.9 pct) under hydrogen in alumina crucibles by means of induction heating. After reweighing, the alloys were cast under argon into 1 mm diam wires. However, it was not possible to prepare some of the Cu-Co alloys with the requisite homogeneity (over about 1 mm3) in this way. For these alloys, reduced powders (purity greater than 99.9 pct) were mixed for 12 to 48 hr, pressed into compacts that were sintered at 1000º to 1050°C for 6 to 48 hr under hydrogen, and then furnace-cooled. Alloy charges of a few mm3, cut from the cast wires or chipped from the sintered compacts, were heated to 1550º to 1600°C in 30 sec in an alumina insert held within a graphite support and then ejected by a pulse of helium onto a lightly polished copper strip on the inner periphery of a rotating wheel. The

Jan 1, 1963

THERE can be little doubt in the mind of anyone of the great interest which has been provoked in the mining and petroleum industry by the com-paratively new geophysical methods of prospecting, after the sessions at this year's meeting of the Institute. Not only were the sessions very well attended but every¬one seemed most attentive. Although the discussion was somewhat limited in general, that may well be at-tributed to the newness of the subject. Two sessions on this subject were planned originally, but these gave insufficient time for the presentation of all the papers prepared and a third session was abso-lutely necessary. The first meeting dealt entirely with the gravity methods and was completed in the scheduled time owing to the fact that but two of the five papers listed were read. The second session was devoted to magnetic and electrical methods, the completion of which had to be carried over into the third period of geophysics. The first session on geophysical prospecting, and in-cidentally the first scheduled Institute meeting devoted entirely to this subject, was most appropriately opened by E. L. DeGolyer, the chairman of the session. It was through the efforts of Mr. DeGolyer that the first gravity work, as applied to prospecting, was under-taken in this country. Again most appropriately, the first paper presented was given by Donald C. Barton, who carried on the first work with the Eötvös torsion balance in America and aided materially in its development. A subject, the theory of which is so difficult to understand as it is generally presented, was so clearly illustrated and ex-plained by the speaker that even a novice could grasp the fundamentals. Dr. Barton, in showing actual re-sults obtained in torsion balance surveys with the in-terpretation of the sane and later drilling records, was free in stating that there are many limitations to the field in which this and the other geophysical instruments may be successfully employed. This paper called for considerable discussion relative to the application of the torsion balance to gravity surveys over various types of structures. During the course of this discus-sion a very important point was emphasized by the chairman, namely, that for successful application of any or all of the scientific methods of prospecting, a back-ground of experience is absolutely necessary to serve as a basis for further work. This can only be secured by contributions from the results of actual prospecting work.

Jan 3, 1928

By R. H. Jacoby, M. J. Rzasa

Experimental equilibrium vaporization ratios were obtained for nitrogen, methane, carbon dioxide, ethane, and hydrogen sulfide in natural gas-condensate systems. Two different overall mixture compositions were investigated over the pressure range 500 to 4,000 psia at 100°, 150°, and 200 °F. Partial phase diagrams of the mixtures were obtained; one of these showed a critical point at 204°F and 3,875 psia. These and earlier data' were compared with the Kellogg correlation' at! 100°F and 1,000 psia. INTRODUCTION The authors' have presented equilibrium vaporization ratios for nitrogen, methane, carbon dioxide, ethane, and hydrogen sulfide in complex mixtures, such as natural gas-crude oil and natural gas-absorber oil. Since mixtures of the natural gas-condensate type also occur widely in petroleum reservoirs and often contain the non-hydrocarbons mentioned, it would be useful to have appropriate K data for calculating equilibrium vaporization conditions. Roland, Smith, and Kave-ler' obtained K's for methane and the light hydrocarbons in gas-condensate mixtures; and Poettmann and Katz3 obtained K's for carbon dioxide in a gas-condensate system. The data presented in this paper extend this coverage to include K's for nitrogen and hydrogen sulfide and phase diagrams for the experimental mixtures. EXPERIMENTAL WORK The equipment and experimental procedure was essentially as described previously, except for analysis of the vapor samples. The vapor sample bombs were filled at the pressure and temperature of the run. Immediately after sampling, a portion of this sample was flushed from the bomb into a 650 cc glass bulb, filling it to near atmospheric pressure. The sample in the glass bulb was then analyzed by the mass spectrometer. Some checks were made on this analytical procedure to find the accuracy of measurement of the C + content of the vapor samples. The modifications tried were complete fractionation of the vapor sample and the use of several liquids (depropanized condensate and retrograde liquid from several vapor samples) as calibrating materials for the mass spectrometer. The results obtained from these various checks differed by about 10 per cent relative and this is believed to be the order of accuracy of the vapor C+ concentrations.

Jan 1, 1953

University of Alabama University, Alabama Mining and Metallurgical Society ROBERT H WHELFSS, President JOHN WINEFORDNER, Vice-President DORACE DODD, Secretary KARL STARK, Treasurer GEORGE T BATOR, Faculty Sponsor PERCY G COWIN, Counselor

Jan 1, 1952

By P. Payson

Intergranular corrosion in corrosion-resistant chromium-nickel steels has been widely discussed in the last few years. So far as the author knows, nothing has been published which definitely shows that this tendency can be eliminated, although suggestions have been made that a remedy is possible if certain specifications are satisfied. Strauss, Schottky and Hinnüberl suggested an increase in chromium content to an extent that would prevent the impoverishment of chromium on carbide precipitation sufficient to cause impaired corrosion resistance in the matrix. Pilling2 suggested an increase in nickel, so that the stability of the austenite matrix would be increased. Aborn and Bain3 say that "intergranular attack—may be eliminated by preventing carbide precipitation (e. g., by lowering the carbon content or somehow raising its solubility) or by precipitating it permanently under conditions which will not remove chromium from solid solution so drastically at any points." In a later paper Aborn and Bain4 state that many different metallic elements, tungsten, vanadium, copper, aluminum, molybdenum, titanium and zirconium, have been added in small percentages to increase the stability of these alloys, but that it has been reported that according to the copper sulfate test these added elements act only to retard the intergranular corrosion. and that increased nickel and chromium contents have similar effects. Newell5 showed that the lower the quenching temperature before reheating, the less severe was the intergranular attack.

Jan 1, 1932

By Paul C. Ragland, P. Geoffrey Feiss

The Piedmont province of the southern Appalachians is the focus of interest for many exploration geologists. In the past, only those deposits with significant surface exposure were exploited. Thus, few deposits have been found and relatively little exploration has been conducted in recent years. Modern geochemical and geophysical techniques can alleviate this problem of concentrating on exposed ore bodies by allowing us to "look through" the soil and saprolite to detect the presence of significant mineralization at depth. This paper will attempt to evaluate the feasibility and effectiveness of several geochemical exploration techniques in the Piedmont province of Cabarrus and Stanly counties, N.C. The area chosen for study is shown in [Fig. 1], lying almost wholly within the Mt. Pleasant quadrangle, N.C. The area is on the eastern boundary between the Charlotte belt, a zone of plutonic and intermediate grade metamorphic rocks, and the Carolina Slate belt, a series of complexly interbedded volcanic and sedimentary rocks of predominantly low metamorphic grade. The area is considered to be an early Paleozoic active, continental margin. l As is typical of most of the piedmont, outcrop is sparse. [Figure 2] is a sketch map of the general geology of the area under study, showing the Charlotte belt rocks in the northwestern quadrant and slate belt rocks to the east. Within the area are a number of old mines and prospects, the most famous of which are the Furniss and Phoenix mines in Cabarrus County. All are reported to have contained Au and Cu. Ag and Pb were reported from some. A summary of the deposits is given in [Table 1]. Data used in this study are from three Master's theses completed at the University of North Carolina at Chapel Hi11. 3, 5, 6 In separate studies, well waters, 5 B-zone soils,3 and vein and float from the area were sampled and analyzed. Each study concluded separately that geochemical anomalies in the vicinity of the ores justify use of that specific sampling technique in a geochemical exploration program. However, no comparative study of the methods has been made. It is our intention

Jan 1, 1980

By R. H. Atkinson

With the object of improving the melting, casting, and working of palladium and 95.5 pct Pd-4.5 pct Ru, the effects of different melting atmospheres (reducing, oxidizing, and neutral), crucible linings, and annealing atmospheres have been studied. Some interesting observations are included about the solubility and diffusion of gases in palladium. THE object of the present work was to ascertain the effect of oxidizing, inert, and reducing ambient atmospheres on the melting and casting of palladium and a Pd-Ru alloy commonly used for jewelry. The need for such a study was indicated during World War I1 when jewelers experienced difficulty in their attempts to make small castings of the torch-melted Pd-Ru alloy by the lost-wax process. When the metal was melted under oxidizing conditions similar to those used for platinum, the castings were gassy; on the other hand, if the melting atmosphere was reducing, the castings were hot-torn and brittle. General Experimental Procedure Pure palladium sponge (99.9 pct Pd) and pure ruthenium powder (99.8 pct Ru) were used for making small ingots (50 g) of palladium and 95.5 pct Pd-4.5 pct Ru by induction melting. The coil, 3 in. high by 2 in. ID with 16 turns, was energized by a 20 kva Ajax high frequency converter. The melting crucibles, so-called sand crucibles, which were made of a highly refractory fireclay, were lined with different materials, including proprietary magnesia, alundum, zircon, and zirconia

Jan 1, 1957

By P. Ramachandrarao, T. R. Anantharaman

CONSIDERABLE interest has lately been evinced as regards the nature of chill zones in solidified metals and alloys. Biloni and Chalmersl were the first to show through their study of segregation substructures in some nonferrous alloys that the formation of the dendritic region may be preceded by a diffusionless solidification process, viz., predendritic solidification. Subsequently Bower and Flemings2 tried a special solidification technique wherein the liquid was drawn into a narrow copper mold with polished surfaces and concluded that convection might trigger some multiplication mechanism leading to grain refinement. Using uncoated and partially coated surfaces for molds in the Bower-Flemings technique as well as in conventional molds, Biloni and Morando3 have very recently brought out the importance of the rate of heat extraction on the mechanism of solidification. We report here on the surface structures and substructures observed in a Sn-1 wt pct Pb alloy solidified at even higher cooling rates (riz., l05 to l07 ºc per sec) than those employed by earlier workers. The alloy was made by melting tin (99.99+ pct) and lead (99.9+ pct) in a silica tube under vacuum. Small quantities of the homogenized alloy (0.5 to 1.0 g) were then quenched (or splat-cooled) from the melt by the "gun technique" developed by Duwez et al.4 The thickness of the resultant foils varied from specimen to

Jan 1, 1970

By R. J. Towner

Tensile properties of Aluminum Powder Metallurgy (APM) products at 600°, 800°, and 1000°F were lowered by cold reductions of as little as 10 or 20 pct. The detrimental effect of cold work on yield strength at elevated temperatures increased with temperature. Heating cold-worked products at 850° to 1150°F removed the structural effects of cold work through the process of recovery and restored, at least partially, the strength at 600°F to the level of hot-worked material. Material containing 5 pct A1203 was recrystallized by cold reductions of 97 pct or more followed by annealing at 1100°F. Recrystallization lowered sharply the strength at room temperature, but raised the strength at 600°and 800°F relative to that of the cold-worked state The high strength of Aluminum Powder Metallurgy (APM) products at elevated temperatures'-4 is well-known. In this paper, some conditions of processing that can affect this important characteristic are presented. The following nomenclature will be used to identify different alloys: All of the above alloys are of the aluminum-aluminum oxide type made from milled powders of commercially pure aluminum with the exception of M486, which is fabricated from atomized A1-Fe alloy powder. The products made from milled powders are hardened by a dispersion of aluminum oxide par- ticles in the aluminum matrix, while the intermetal-lic compound FeAL is the dispersion hardening agent in M 486.' The process used for making all APM products involves the application of heat and pressure to form a compact from powder which is fabricated into an extrusion, sheet, strip, or wire by standard techniques. Probably the most common cold-worked APM product is sheet. Cremens, Bryan, and rant' determined the room-temperature tensile properties and the 600°F stress-rupture properties of XAPOOl and XAPOO3 sheet and reported that there was little difference between the as-extruded, cold-worked, and annealed at 1200°F conditions. On the other hand, Emmons6" found that the tensile and stress-rupture properties of XAPOOl and XAPOO3 sheet at 600" and 800°F were lower than those of extrusions. The tensile properties of XAPOO3 sheet were also determined at elevated temperatures by Doyle' and ~ayward.' According to Friske" and Kendal et a1.," cold working by swaging, rolling, and tube drawing reduced the tensile and creep-rupture strength of XAP 001 Recrystallized aluminum powder metallurgy products are rare because the dispersion in the aluminum matrix is usually too fine, uniform, and concentrated to permit recrystallization. However, Lenel12 was able to recrystallize wires made from aluminum powders containing about 1.75 and 3.0 pct oxide and found that the tensile properties at room temperature remained higher than those of annealed commercially pure aluminum because of the dispersed oxide particles. Westerman and Lenel13 found the kinetics of recrystallization of the powder products were very different from those of cold-drawn commercially pure aluminum wire. The alloy containing 3.0 pct oxide recrystallized to a very coarse grain size was more creep-resistant at 400" to 600°C (752" to 1112°F) than in the as-extruded, fine-grained condition, according to Ansell and weertman.14 Ansell and aenel" further studied creep at 500" to 620°C (932" to 1148°F) of recrystallized 1.75 pct oxide wire and confirmed the creep model of Ansell and Weertman. The present work is being reported for the fulfillment of the following objectives: 1) to show the effect of cold work on tensile properties at elevated temperatures;

Jan 1, 1964

By A. W. Demmler

RECENTLY, Chaudron,&apos; Montariol,2 and their co-workers published the results of their studies on zone-refined aluminum. They found their material to be capable of recrystallization at —50°C, but gave no data as to the percentage reduction or time required. Their material was found to be practically non-work hardening at room temperature, but after 96 pct cold work at a low temperature and storage in liquid nitrogen it was found to recrystallize to coarse grains in less than 3 hr at 20°C. Recently, a study was made of the room temperature recrystallization characteristics of zone-melted aluminum. An ingot 14 in. in length, with a 3hx3 in. cross section, was made in an extremely high purity graphite boat under an atmosphere of dried commercial argon. It was made by first passing the molten zone along the ingot of 99.99+ pct A1 15 times. At this point, the most impure 3 in. (the end toward which the eutectic forming impurities migrated) were replaced with more of the original starting material, and 15 more traverses were made. Each traverse of the zone along the ingot required approximately 3 hr. Three ingots were prepared in this identical fashion and the chemical analyses were made spec-trographically on two of these ingots, rather than on the one used in this investigation. The analyses were made at 1 in. intervals along the ingot, in duplicate. Over the purest 5 in. of the ingot, which were most important in this investigation, there was found an average composition of <0.00004 pct Cu, <0.0003 pct Fe, <0.0001 pct Si, and <0.0001 pct Mg. In addition, the following elements were not detected spectrographically even in the more impure end of the bar: manganese, zinc, nickel, chromium, titanium, vanadium, lead, tin, boron, beryllium, bismuth, gallium, zirconium, cadmium, antimony, cobalt, and molybdenum. The original ingot was given several cold reductions, with intermediate anneals in order to refine the grains. Owing to the extreme length resulting and the ease of deforming the material plastically, it was cut into eight equal lengths and identified as shown in Fig. 1, with the highest numbered section at the purer end (that enriched with peritectic formers). Section 6 was used in the exploratory work and was found to be of exceptionally high purity, giving more rapid rates of room temperature re crystallization than any previous aluminum studied at the Alcoa Research Laboratories. This fact suggested that the entire midsection of the ingot might be of very high purity. Accordingly, section 4 was chosen for the next study. A portion of it was rolled to cold reductions of 10, 25, 40, 60, 75, and 90 pct at room temperature, and the re-crystallization of each specimen was followed by X-ray pinhole transmission photographs. The other portion received the same treatment, except that both the specimens and the rolls were maintained at 160°F in the process of rolling. The latter ortion was retarded in its recrystallization as compared to the former, probably due to the stress relief effect of the warm rolling. Both of these portions of the fourth section were found to recrystallize at a considerably slower rate than did the sixth section.

Jan 1, 1957

By L. W. Kempf, K. R. Van Horn

DURING the recent development of aluminum alloys for free-cutting screw-machine rod, it became desirable to know something of the solubility of lead and bismuth in liquid aluminum and in some aluminum alloys. The literature is not particularly helpful in supplying this information. These portions, therefore, of the constitutional relationships of aluminum-bismuth and aluminum-lead alloys were investigated by thermal analysis and by chemical analysis of samples taken from aluminum-rich melts in equilibrium with precipitated lead or bismuth. The solubility of lead and bismuth in some liquid aluminum-copper alloys was also investigated. Some consideration was also given to the solubility of these elements in solid aluminum. Among the earliest investigators of the aluminum-lead and aluminum-bismuth systems was Wright,1 who reported that melts of aluminum and lead formed two layers indicating limited liquid solubility. Under his conditions, the aluminum-rich layer was reported to contain 1.91 per cent Pb and the lead-rich layer, 0.07 per. cent Al. Subsequently, Pecheau2 found that in aluminum-rich alloy melts with more than 10 per cent Pb three layers were distinguishable. He reported that the middle layer contained from 3 to 10 per cent Pb. He also found that the melting point of aluminum appeared to be lowered slightly by the addition of lead. Gwyer3 investigated these alloys and found evidence of a slight lowering of the freezing point of aluminum by the addition of either lead or bismuth. He found no evidence of solid solubility in either case and made no attempt to determine the liquidus curves. Hansen and Blumenthal4 reported that the addition of lead distinctly lowered the solidification point of aluminum. They also found that bismuth lowered the melting point of aluminum. Guillet5 reported almost complete mutual immiscibility for the aluminum-bismuth alloys in the liquid state. Bohner6 examined the effect of various concentrations of lead and bismuth on the electrical conductivity of aluminum. He found decreases in conductivity on annealing at 500° C. as compared with the conductivity of the same alloys on annealing at 300° C.

Jan 1, 1938

By E. S. Machlin, A. J. McEvily

HE results of an experimental investigation by McEvily and Machlin have indicated that a strong relationship exists between the processes of cross slip and fatigue. Whenever dislocations can cross onto an intersecting plane and expand thereon, as in AgCl crystals, the usual type of S-N behavior is obtained, but when such a process is difficult, as in NaCl crystals, fatigue does not occur in its usual manner, if at all. MgO, because of its crystal structure (NaCl type) and slip systems ({110}<110>) would not be expected to fail in fatigue. However, Cornet and Gorum2 have found something akin to the usual type of fatigue behavior for MgO crystals. The purpose of this note is to attempt to resolve this apparent discrepancy. In Cornet and Gorum&apos;s work as-cleaved crystals were tested under cyclic axial loading, whereas in McEvily and Machlin&apos;s work chemically-polished crystals were tested in reversed bending. Because of the difference in specimen preparation, the major effort of the present work was directed toward comparing the behavior of as-cleaved as opposed to chemically-polished specimens. The effect of type of loading seemed less important, but a check was made on this also. Eighteen bend tests and one axial load test were made. The specimens were cleaved from Norton magnorite blocks, and measured 1 by 3/16 by 1/8 in. To avoid failures in the grips, the thickness of the bend specimens was reduced from 1/8 in. near the ends to 0.04 in. in the central portion. This reduction was from one side of the crystal only. Twelve specimens were polished in orthophosphoric acid to remove the damage due to cleavage. The other six specimens were not chemically polished so as to maintain the as-cleaved condition of the crystal faces which had not been reduced. The axial-load specimen was reduced from both faces to a thickness of

Jan 1, 1962

By Robert Lepsoe

It is generally realized that in cyaniding the precipitation efficiency of zinc dust is due to the fine division or extended surface of its metallic particles; but frequently it is thought that the presence of other metals, say 2 to 3 percent. lead, is advantageous, causing more complete precipitation. The results of testing about fifty brands of commercial zinc dust have led to the conclusion that there is a distinct relation of precipitation efficiency to fineness and that the effect generally can be estimated by examining the size of metallic particles. The presence of lead was not found to be of any importance. Specifications Generally the term "97 per cent. to pass a 350-mesh screen, 95 to 97 per cent. uncombined metallic zinc" is used by the leading European exporters. Among the many methods of determination of metallic zinc, I have found the iodine test (iodine in potassium iodide) very satisfactory and rapid. It has been controlled by the other methods, samples of the same product having been sent to three different analysts: Iodine method................... 98.11 per cent. metallic zinc, Volumetric method.............. 07.63 per cent. metallic zinc, Ledoux Co., New York Bichromate method.............. 08.16 per cent. metallic zinc, Watson Gray, Liverpool. England Bichromate method.............. 98.20 per cent. metallic zinc, Norway Inst. of Tech., Trondhjem Determination of Precipitation Efficiency The method devised by W. J. Sharwoodl was used. The method proved to be satisfactory, the tests being merely for the comparison of different samples, hence the personal factor in manipulation was eliminated. As nearly all tests showed more zinc in solution than was accounted for by the silver precipitated, the term "dissolved zinc" was introduced—it means zinc dissolved by the action of cyanide and oxygen: Zn + 4KCN + H2O + O = K2Zn(CN)4 + 2KOH; or more probably, resolution of its equivalent precipitated silver, as tests stirred two hours showed more "dissolved zinc" than those stirred

Jan 1, 1925

By H. Conrad, V. V. Damiano, G. J. London

A method is described for producing single crystals of high-purity beryllium, Be-4.37pct Cu, and Be-5.24 pct Ni. These crystals were prepared for testing in compression parallel to the [0001] by orienting and lapping to within ±3&apos; of arc of the (0001). Microstrain testing apparatus is described along with c axis compression results for ingot purity beryllium, twelve-zone-pass material, and the above-mentioned alloys. Results show no measurable plasticity for the ingot purity material from -196" to 400°C, although some surface traces of (1122) slip was observed at 200°C and above. The twelve-zone-pass material shows substantial microstrain plasticity at 220°C with slip on (1122). Both alloys show significant plasticity at room temperature and above with slip also on (1122) planes. THE two slip systems which normally operate during the plastic deformation of beryllium in the vicinity of room temperature are:&apos; basal slip (0001)(1120) and prism slip . Pyramidal slip with a vector inclined to the basal plane has been reported for elevated temperatures,&apos;-a but occurs near room temperature only at very high stresses.~ A summary of the available data on the effect of temperature on the critical resolved shear stress for slip on these systems has been compiled by Conrad and Perlmutter.~ It has been postulated6&apos;7 that one of the principal factors contributing to the brittleness of poly crystalline beryllium at temperatures below about 200°C is the difficulty of operating pyramidal slip with a vector inclined to the basal plane. Hence, detailed information on the operation of such a slip system is important to understanding the brittleness of beryllium. The operation of pyramidal slip with a vector inclined to the basal plane is best accomplished in beryllium by compressing single crystals in a direction parallel to the c axis. In such a test the resolved macroscopic shear strzss on the basal and prism planes is zero and (1012) twinning which is favored by tension along the c axis does not occur. Hence, in c axis compression of beryllium the normal deformation modes are inhibited and the operation of pyramidal slip with a vector inclined to the basal plane is favored. In the present investigation, c axis compression tests were performed on beryllium single crystal as a function of temperature (77" to 700°K), purity (commercial and twelve zone pass), and alloy content (4.37 wt pct Cu and 5.24 wt pct Ni). Presented here is a description of the test techniques employed and the gross mechanical behavior observed. A detailed analysis of the slip traces developed on the surfaces of the deformed specimens during these tests and the results of electron transmission studies of the deformed crystals are given in a separate paper.B PROCEDURE 1) Materials and Preparation. Single crystals about 1 in. diam were prepared of the following materials: commercial-purity beryllium, high-purity beryllium, and two beryllium alloys, one with 4.37 wt pct Cu and the other with 5.24 wt pct Ni. The commercial-purity single crystals were obtained by cutting specimens from large-grained ingot of Pechiney SR material, which is approximately 99.98 pct pure. The high-purity crystals were prepared by floating-zone refining (twelve passes) a rod (7 in. by 1 in, diam) of Pechiney SR grade cast and extruded beryllium. Although an absolute chemical analysis of the zone-refined material was not established, mass spectro-graphic analysis, emission spectrographic analysis, and y activation analysis indicated that it contained in atomic fractions about 5 to 10 ppm each of carbon and oxygen, 1 to 5 ppm each of nickel and iron, and about 1 to 2 ppm of copper, with the remaining residual impurities being less than 1 ppm. Further indication of the purity of this material is provided by the critical resolved shear stress for basal slip, which was approximately 300 psi. The starting material for the alloy single crystals was 1-in.-diam floating-zone-refined (six passes) rod of Pechiney SR grade beryllium. Two such rods were wrapped respectively with sufficient weight of wire of high-purity copper (99.999 pct) or nickel (99.999 pct) to yield a 5 wt pct alloy. A seventh floating-zone pass was then applied to each of the rods to accomplish the initial alloying and an eighth pass for homogenization. Analytical samples were taken from regions of the rod immediately adjacent to where the mechanical test specimens were cut; these indicated 4.37 wt pct Cu and 5.24 wt pct Ni. 2) Crystal Orientation. To avoid the occurrence of basal slip during c axis compression testing, it is necessary to load the crystals as nearly parallel to the c axis as possible. Preliminary c axis compression tests indicated that plastic flow and/or fracture occurred at stresses of the order of 300,000 psi; hence on the basis of a critical resolved shear stress for basal slip of 300 to 400 psi, the maximum crystal misorientation permitted is about 4 to 5&apos; of arc. Since this accuracy cannot be obtained using the usual back-

Jan 1, 1969

By A. W. H. Morris, G. H. Laurie, J. N. Pratt

Using- galvanic cells of the form Sn(liq)/Sn" (LiCl-KC1-SnCl,)/Sn-Ag (alloy), measurements have been made of relative thermodynamic properties of the a, C, E, and liquid phases of the Ag-Sn alloy system. Partial heats of solution of the components in the liquid alloys lzave also been observed by direct cal-orimetric measurement in an isoperibol calorimeter. The thermodynanzic quantities are disczlssed in relation to structural and other properties and the existence of anomalous minor fluctuations in the partial heats and entropies of solution in liquid alloys is tentatively suggested. In the course of a recent electro motive-force study of the thermodynamic properties of Sn-Ag-Pd liquids,&apos; some measurements were also performed on the Ag-Sn binary system. Most previous thermodynamic studies of this system have been concerned with the liquid state. Measurements confined to the limiting heat of solution of silver in liquid tin have been made by many calorimetric workers2 while high-temperature calorimetric measurements of the heats of formation of the full range of liquid alloys are reported in the early work of Kawakami~ (1323°K) and more recently by Wittig and Gehrin~(1248°K). Electromotive-force studies on liquid alloys have been made by Yanko, Drake, and Hovorka&apos; (606" to 686°K; 86 to 99.4 at. pct Sn) and by Frantik and Mc Donald&apos; (900°K; 30 to 90 at. pct Sn). The only known measurements on the solid state are of heats of formation of the a, £, and c phases; these values were obtained using tin-solution calorimetry, at 723"K, by Kleppa,~ whose investigation also yielded heats of formation of liquid alloys containing more than 64 at. pct Sn. The present experiments on the Ag-Sn alloys include a re-examination of the liquid phase and, because of the dearth of free-energy data for the solid state, attempted measurements on the a, c, and E phases. The principal new feature of electromotive-force results obtained for the liquid phase was an indication of anomalous fluctuations in the partial heats and entropies of solution of tin at certain compositions. However, since the values for these thermodynamic quantities were determined from the temperature coefficients of cell potentials, which are commonly subject to considerable error, confirmation by calorimetric measurements was considered desirable. A detailed investigation of the partial heats of solution of the components in the binary liquids was made using a liquid metal solution calorimeter. I) GALVANIC CELL STUDIES a) Experimental Details. Measurements were made, as a function of alloy composition and temperature, of the potentials of reversible galvanic cells of the form: ~n(liq)/~n++/~n-Ag (solid or liquid alloy) Details of the apparatus and experimental techniques have been given elsewhere.&apos; so that a brief account will suffice here. Molten salt, 58 mole pct LiC1-42 mole pct KC1, containing small amounts (1 to 2 mole pct) of stannous chloride was used as the electrolyte. The salts were dehydrated by pre-electrolysis and vacuum -drying techniques. Cells were established under an argon atmosphere by immersing tin and alloy electrodes in the molten salt contained in a large silica tube, heated in a vertical resistance furnace. The tube was sealed at the top by a head plate provided with openings permitting the simultaneous insertion of six electrodes, a central thermocouple sheath, and connections to vacuum and argon lines. Temperatures were controlled to *0.2"C over prolonged periods, with maximum variation over the electrodes at any time of 0.l°C. Temperatures were measured with a standardized Pt/13 pct Rh-Pt couple. The electromotive force of this and the cell potentials were measured on a Cambridge Vernier potentiometer and short-period galvanometer. Alloys were prepared from Pass "S" tin (99.999 pct) and Johnson-Matthey high-purity silver (99.999 pct) by melting in evacuated silica capsules and quenching in cold water. For liquid phase experiments, pieces of the resulting alloys were remelted into prepared silica electrode units, while solid electrodes were prepared by remelting into 3-mm bore tubing, inserting a cleaned molybdenum lead wire, and quenching to produce uniform rods about 3 cm in length, with soundly attached leads. In all cases remelting was done under an argon atmosphere. The solid electrodes were subsequently annealed in evacu ated silica tubes for 14 days at about 20°C below the solidus and quenched. Analyses showed that these techniques produced uniform electrodes with no significant change from weighed out compositions. b) Results and Discussion. Measurements were made on about forty alloys in the solid and liquid states, over varying ranges of temperature between 550" and 1050°K. Stable, mutually consistent, and reproducible electromotive-force data were obtained with most liquid alloys and these are shown in Fig. 1. Investigations were extended below the liquidus tem-

Jan 1, 1967

By Olav Dalen

A HUNDRED years have passed since Wöhler made the first few particles of aluminum by decompos-ing aluminum chloride with potassium. In 1854 Deville used sodium to decompose the double chloride of aluminum and sodium, but even various subsequent improvements of the process, especially by Castner, did not sufficiently decrease the cost of the metal to bring it into general use. In 1862 Monckton proposed to reduce Al O? with carbon by the aid of the electric current, but the efforts of the Cowles brothers to do so were not successful and in 1884 they turned to making aluminum alloys by electrolysis. At about the same time Hall in America and Heroult in France success-fully worked out the technology of dissolving A12O3 in fused cryolite and electrolyzing the bath. It is hard to realize that forty years ago the annual production of aluminum was only 30 to 40 tons per year and the price of the metal thirty times what it is today. Great strides in decreasing the cost of production, improving the quality of the metal, and increasing the output have been made in the lifetime of middle-aged men. The large consumption of electrical energy in the form of direct current makes it necessary to locate aluminum-producing plants near waterfalls, to avoid transmission losses. Norway with its abundant water-falls is therefore a logical place for the development of aluminum production, even though it is necessary to import the bauxite, which is the raw material of the process. It was foreigners who first started the aluminum in-dustry of Norway and the first two plants were built by the British Aluminium Co. in 1906 to 1908; one at Vigeland near Kristiansand, and the other at Stavan-gerfjord in Nordfjord. These two plants are still oper-ating and producing over 3000 tons a year. When the plant at Vigeland is enlarged the production of the company will be more than 4000 tons a year.

Jan 11, 1927

By J. J. Frawley, W. J. Childs, W. R. Maurer

The object of this investigation was to determine the growth habit of bismuth and bisrrtuth alloy dendrites as a function of supercooling. To do this, techniques were developed to increase the amount of supercooling in bismuth and bismuth alloys. For pure bismuth, the growth habit was dependent on the amount of supercooling. At low amounts of supercooling, about 10" C, prismatic dendrites were obtained. With increased supercooling, about 20 C, a hopper growth habit was observed. In many cases where hopper growth had occurred, the hopper dendrites were twinned during the growth process. This twinned surface enable prismatic dendrites to nucleate and grow by a twin plane mechanism. When the amount of supercooling was increased to about 25 °C, the growth habit was a triplanar growth. With still greater supercooling, about 3s°C, a branched growth habit occurred. The exposed planes on the prismatic, hopper,, triplane, and branched dendrites have been determined. The growth habit of the dendrites which grew along the crucible wall was found to have the (111) as the exposed plane, with <211> growth direction. It is apparent that dendritic growth of a metal is dependent on its purity and the solidification variables present. One of the solidification variables is the degree of supercooling. Supercooling, although often observed, has not been studied extensively until recent years. For dendritic growth to occur in a pure metal, the metal must be thermally supercooled. After the dendrites grow into the supercooled melt, the heat of solidification raises the temperature of the specimen to the melting point of the material and the remaining liquid will solidify at this temperature. Decanting is the removal of this remaining liquid before complete solidification. This removal of the remaining liquid after recalescence had occurred is a great aid in the study of dendritic growth. In this investigation, decanting was accomplished by a vacuum-decanting technique . Other investigators1-5 have studied the growth characteristics of various low-melting-temperature pure metals and alloys as a function of supercooling. However, large degrees of supercooling were not included. For their study of dendritic growth of lead, Weinberg and chalmersl employed a decanting technique which was achieved by pouring off the remaining liquid, exposing the solid/liquid interface. This method was employed later by Weinberg and Chalmers2 for the investigation of tin and zinc dendrites. The method for obtaining a solid/liquid interface was improved by Chalmers and Elbaum. They employed a triggered spring which was attached to the solidifying section of the specimen. Upon activation, the spring jerked the solid interface away from the liquid melt. In the study of growth from the supercooled state, a metal of low melting point which exhibited a high degree of supercooling was desired. Bismuth gave very consistent supercooling when a stannous chloride flux was employed. The maximum supercooling obtained was 91°C, with an average supercooling of between 65" and 75°C. The consistency of supercooling greater than 50°C was very high. The use of vacuum to aid in the rapid decanting of molten metal has proven to be very successful in this investigation. The vacuum gives a rapid decantation, usually leaving the solidified metal structure sharply defined. The purpose of this investigation was to study the effects of supercooling and the effects of alloy additions on the growth habit of bismuth dendrites. The structure of bismuth has been variously defined as face-centered rhombohedral, primitive rhombohedral, and hexagonal. However, bismuth has only one plane with threefold symmetry, the (111) plane, and the crystal-lographic structure is considered a 3kn structure. MATERIALS The bismuth which was employed in this investigation was obtained from the American Smelting and Refining Co. of South Plainfield, N. J. The accompanying spectrographic analysis data indicated the bismuth to be 99.999+ pct pure. The tin was obtained from the Vulcan Materials Co., Vulcan Detinning Division, Sewaren, N. J. It was classified as "extra pure". Nominal analysis was 99.999+pct. In order to prevent contamination of the bismuth melt from the atmosphere, an anhydrous stannous chloride (Fisher certified reagent grade) was added to each melt. The fluxing action obtained from the use of the chloride provided a large amount of supercooling in the specimen. APPARATUS A 30-kw, 10,000-cps motor-generator set, connected to a 6+-in.-diam air induction coil, was employed to melt and superheat the specimens. The temperatures were recorded by means of a chromel-alumel thermocouple and a potentiometric recorder. The thermocouples were 0.003 in. in diam, and were encapsulated with Pyrex glass to prevent the thermocouple from acting as a nucleating agent and also from contaminating the melt. Fig. 1 illustrates the vacuum-decanting apparatus when a liquid flux was employed. A standard 30-ml Pyrex beaker was placed on top of an asbestos insulating block. A 5-mm-ID Pyrex tube with aA-in. spacer tip attached to its end was used for the decanting tube. The spacer tip contributed significantly to a successful decanting operation. The tip located the opening of the decanting tube about -^ in. from the bottom of the

Jan 1, 1969

By F. H. McDowell

DURING the last eighteen months the Tilly Foster Iron Mine Company, the President of&apos; which is Mr. E. I?. Hatfield and the Managing Director Mr. B. G. Clarke, has been carrying out a plan

Jan 1, 1889

[Executive HENRY A. BUEHLER, Chairman ERLE V. DAVELER EDGAR RICHARD JOHN M. LOVEJOY WILLIAM WRAITH J. V. W. REYNDERS, Consultant Finance HENRY KRUMB, Chairman E. E. ELLIS PAUL D. MERICA H. G. MOULTON, Consultant]

Jan 1, 1936

By C. P. Proctor, J. B. Morrow

With numerous plans under consideration for coal classification, and with the advent of the Bituminous Coal Code, the intelligent sampling of coal has become increasingly important. To us it is rather significant that there have been very few fundamental studies of coal sampling in American technical literature since those of E. G. Bailey, which appeared in the Journal of Industrial and Engineering Chemistry in March, 1909. He covered the subject up to that time so thoroughly and in such an excellent manner that perhaps many other later students have felt that they could add very little to his findings. The recent studies of the British Engineering Standards Association have indicated the possibility of a somewhat different interpretation of Bailey&apos;s results, permitting the taking of smaller samples, and perhaps it will now be helpful to reopen this question. C. W. H. Holmes, in an informative series of articles on coal sampling recently published in Colliery Engineering, makes two rather interesting statements, as follows: It is scarcely surprising to find a lack of interest and knowledge regarding the sampling of coal not only in the mining industry itself but also among consumers of industrial fuel: at its best coal sampling is a dirty business, regarded as a nuisance and an expense by the commercial man, and usually as a nuisance and nothing else by the chemist. The writer can conceive only two classes of people who have never experienced any difficulty in obtaining representative samples of coal from wagons; those who have never tried to, and those who have never had the necessity or desire to check the accuracy of their work. The primary purpose of this paper is to present some tabulated data of the more significant results of a sampling investigation undertaken during the last four years to obtain certain fundamental data on the variables connected with coal sampling and to point out that often assumptions have been made that are not in accordance with the facts. One of the standard sampling methods states:

Jan 1, 1936