Search Documents

By A. A. Hejja

The first part of this study deals with the importance of surface tension of slags produced in the smelting of sulphide concentrates. Theoretically the method of determining the surface tension of slags was laid down by Boni and Derge. The values obtained experimentally for a series of main oxide components were grouped into a useful correlation incorporating experimental constants for the relevant oxides present in the slag, some of these giving the surface tension value for the particular slag. These estimated values were coupled with or incorporated into the slag viscosity plots to show the correlation between the two factors. This is also important from a refractory attack point of view in the furnace operation. In the second part an attempt is made toward the optimisation of slag composition relevant for electric furnace smelting processes. Using the knowledge of the viscosity and electrical conductivity of the slags at the temperature of furnace operation, the mode of optimisation is based on correlations which utilize the trend of the mostly parabolic plots of viscosities and conductivities. The results obtained by this method agree well with the optimum slag compositions being used in established operations derived from years of practical experience for various slags used in the furnaces. However, due to extensive turbulence in suspension and gas injected bath smelting processes, the outlined methods cannot be used for these processes. Also great caution should be exercised in their application for three electrode circular furnaces with separate slag cleaning.

Jan 1, 1997

By Fernando Castro

Electric furnace steelmaking dust is a polluting residue that needs to be treated in order to recover metals contained and to produce an environmentally acceptable residue. Some hydrometallurgical approaches for its treatment have been evaluated, namely: caustic soda leaching followed by electrolytic recovery of zinc, ammonia leaching followed by zinc compounds precipitation and acetic acid leaching followed by lead, zinc hydroxide and gypsum precipitation.

Jan 1, 1992

By Norbert L. Piret

From the copper smelter operation a various outputs are to exert negative impacts on the environment. Particularly, emissions like SO2 and dusts, solid wastes like contaminated gypsum and arsenic sludge, effluents and heated cooling water are generated. Most countries have sitipulated an environmental legislation to provide the framework for an efficient environmental management. As part of the planning activities for x major greenfield copper smelter, the Following elaborations are required and were drawn up. -The Environmental Impact Assessment which is the first step of environmental management and mandatory for every new project. - The Environmental Monitoring Plan, which describes the monitoring procedures for the main impacts identified and assessed. -The Environmental Management Plan, which deals with the minimization of environmental impacts, and the methods of its implementation.

Jan 1, 1996

By Roland Loewen

A review of the aqua regia method for the recovery of gold from jewelry shop wastes is given. Also outlined is a specialized procedure for the recovery of the silver that occurs in these wastes. A classic method for the recovery of platinum and palladium is, given. There is a brief review of other gold and silver refining methods. Environmental conditions are discussed and a few perhaps, new and useful processes ,are mentioned. References are by author or editor and are listed alphabetically. Suggestions for further information in the field of precious metals, are given in a final list.

Jan 1, 1989

By J. Fogarty, J. Sofra

The mobile telecommunications sector is one of the fastest growing industries worldwide. However, increasingly stringent environmental regulations are placing pressure on manufacturers to accept responsibility for end of life products. The companies are therefore exploring avenues to recover the valuable components contained within the mobile telecommunications devices thus reducing the quantities of toxic components going to landfill. Batteries used to power the devices, are typically based on either nickel-cadmium, nickel metal hydride, or lithium ion cells. They contain toxic metals including nickel, cadmium, lithium, potassium, lead, and cobalt in a complicated arrangement of battery cells surrounded by a metals then plastic casing. The Ausmelt Catalytic Waste Converter (CWC) for waste treatment and recycling is well suited to processing all three mobile phone battery types for the recovery of valuable metals in marketable products that can be recycled to industry without turning out harmful levels of toxic emissions. Ausmelt recently demonstrated the capabilities of its CWC by continuously processing 4.5 tonnes of nickel-cadmium batteries. Using Ausmelt's pilot plant facility in Australia, the nickel-cadmium batteries were processed to produce a nickel iron sulphide (matte), a cadmium fume and a final slag which satisfied CS toxicity leach test criteria and was safe f<~r disposal to landfill. This paper explores the commercial development of the Ausmelt CWC for treating each of the three battery types in light of (a) the outcomes of the recent demonstration, and (b) the current and expected future availability of batteries for processing.

Jan 1, 2000

By Oszkar Bíró, Peter Mittag, Bernhard Aigner, Stefan Pirkeri, Philipp Glttleri

"This paper considers CFD modeling of processing and melting of small metallic particles by means of electrical heating. The particles fall continuously onto a liquid metal bath which is heated by an electric arc. After melting of the particles liquid metal is tapped.The charging behavior of the particles in the supply unit as well as in the reactor freeboard is studied by means of Euler-Euler granular simulations. The flow situation in the metal bath due to gas injection and magnetic fields is calculated by combining Navier-Stokes and Maxwell solvers. The macroscopic melting process occurring during the continuous charging of the particles is studied by kinetic laws for melting reactions. The temperature field is evaluated by balancing heat sources due to Joule's heating and heat losses due to latent heat of melting as well as convection and radiation.As a result of these simulations the fully three-dimensional flow fields of particles and gas in the atmosphere is obtained. Furthermore the flow field as well as the magnetic field in the metal bath can be studied. As a main result the three-dimensional concentration field of the still unsolved particles in the liquid metal can be evaluated.IntroductionIn this paper a metallurgical process for melting small iron particles is investigated by means of CFD-simulations. In a first process step the preheated and already mostly reduced iron particles fall continuously into the reactor through a vertical tube mounted at the lid of the furnace. In a second step the particles are melted in the liquid metal bath. Meanwhile the melt is heated by electric arcs to provide the heat needed for melting the incoming particles.In Figure I a sketch of the geometry setup considered in this paper is provided. The particles fall from a height of approximately 12 meters onto the bath surface in the center of the furnace. The melt is heated by electric arcs that are placed symmetrically around the center axis."

Jan 1, 2001

By Jason M. Porter, Douglas L. Porter, David L. Olson, Travis W. Koenig, Van S. Blackwood, Brajendra Mishra, Robert D. Mariani

"Traditional alloy theory models have been applied relative to the three solid phases of uranium: alpha (orthorhombic), beta (tetragonal), and mainly gamma (body centered cubic)[l]. The Darken-Gurry and Miedema models, with modifications based on concepts of Waber, Gschneidner, and Brewer have been used to predict the behavior of four types of solutes: 1) Transition associated with alloying in and containment of the uranium fuel 2) Transuranic elements in the uranium 3) Rare earth fragmentation elements (lanthanides) 4) Transition metals and other fragmentation elements. Using these solute map criteria, elemental behavior have been predicted as highly soluble, marginally soluble, or immiscible (intermetallic phase formers) and have been used to compare solute effects during uranium phase transformations. The overlapping of these solute maps are convenient first approximation tools for predicting alloy behavior.IntroductionAn investigation is in progress to determine the role of various solute elements on size and shape of the 'Y phase field range for uranium to optimize the burning and material processing of nuclear fuel is in progress. Traditional alloy theory models based on correlations to elemental electronic and crystal properties are used to predict solubility and micro structural formation. The effectiveness of this model is based on microstructure property correlations. Darken and Gurry, and Miedema models, with modifications based on concepts of Waber, Gschneidner, and Brewer, models have been used to describe solute solubility with respect to uranium based the on correlation between elemental electronic structure and uranium phases. The alpha (orthorhombic), beta (tetragonal), and gamma (body centered cubic) phases have different solubilities for specific alloy additions as a function of temperature. Using the method of Waber, ellipse diagrams classified those solutes that should have broad solubility in the allotropes of uranium[2]. The predictive diagrams are made from four different correlations:"

Jan 1, 2012

By Micheal McCarter, Biswadeep Saha, Meenakshisundaram Ramanathan, Chai Ren, Sivaraman Guruswamy

"Three-point bend test was used to study the effect of electrochemically charged hydrogen and magnetic field on the embrittlement behavior of AISI 4340 steel in this work. Acoustic emission signals were collected during the test and analyzed to gain an understanding of the crack growth process. Cathodic hydrogen charging in AISI 4340 steel resulted in drastic reduction of ductility and strength. Hydrogen embrittlement was characterized by a change in fracture surface from dimpled ductile surface to quasi cleavage type fracture. No significant effect was observed in the presence of magnetic field. The acoustic emission signals collected during the test provided an indication of the extent of energy released during the crack growth process.*Support of this work by NSF through the award DMR-0854166 is gratefully acknowledgedIntroductionGrowing interest in hydrogen as a clean fuel and use of steel and other iron based alloys for storage and transport of hydrogen has led to extensive study of the influence of hydrogen on the mechanical properties of these alloys. Hydrogen interaction with materials may result in degradation of mechanical properties. Embrittlement, either ductile or brittle, can be described as a condition which decreases the toughness of the material or increases the ease of crack growth. Hydrogen present even in few parts per million is sufficient to embrittle steels at room temperature [1]. In most cases, hydrogen exposure is through an electrochemical process in aqueous corroding environments. In such cases, they are prone to be exposed simultaneously to electrically induced magnetic fields, which are also believed to affect the hydrogen embrittlement susceptibility of these alloys. So it is also important to study the effect of magnetic field on the hydrogen embrittlement susceptibility. Hydrogen solubility by electrochemical process in aqueous solution is proportional to square root of current density for iron. [2,3]"

Jan 1, 2012

By D. C. Foguel, J. L. R. Bravo

For several years, Caraiba Metais S.A. (CMSA) had to stock the arsenic sludge generated from the electrolyte purification process of its tankhouse. The amount stocked · reached approximately 3,500 tonnes, as the effects of its recycling during the smelting process and consequently in the sulfuric acid plant were unknown. Besides, it had as limiting factors the high content of arsenic in the copper concentrates supplied by foreign countries as well as the reduced capacity of the tankhouse's purification plant. The choice for selling the mentioned residue, which generally contains more than 50% of Cu, was attractive, but the environmental policies and regulations had not allowed this option. Other alternatives, such as the production of bicupric arsenic by means of a solvent extraction process or arsenic trioxide, were considered but the economic feasibility was not attractive due to the absence of a domestic market and a poor international market. After a study of the arsenic partition in the metallurgical process, it was verified that the residue could be recycled without causing any operational problems or damage to the environment. To make this possible, the capacity of the purification plant was increased and the way of removing the arsenic sludge from the cells was modified from manual to mechanical, therefore avoiding the direct contact of the workers with this poisonous substance. Moreover, procedures for recycling in the smelter were established and tolerance limits were set for both the smelter and the sulfuric acid plant. The main amount of arsenic to be recycled is released with the smelting furnace off-gas, which is washed during the purification stage of the sulfuric acid plant. The acid water, rich in arsenic, is then treated in the waste plant and the arsenic, in its stabilized condition, is confined in an appropriate area.

Jan 1, 2000

By M. Z. Sukiennik

A static method for vapor pressure measurement up to 1450 K and above 1 hPa is presented. The method is designed for equilibrium and kinetic studies of metallic systems, including those with a chemical reaction. Application examples are given for determination of activities in condensed phases, and heterogeneous reaction rates and equilibrium constants.

Jan 1, 1993

By S. V. Subramanian

The tool material and the machine design for high speed machining are well advanced over the last decade but the steel design has lagged behind. The paper examines the design of steel in order to control the sliding tribology for high speed machining under dry machining conditions. In high speed machining of steel, accelerated chemical wear of the tool occurs once atomic contact is established at the tool-chip interface, resulting in poor tool life even with high performance tools such as cubic boron nitride. Recent research has confirmed the occurrence of nanocrystalline grains in the interfacial layer of the chip at the tool-chip contact. The volume percentage of grain boundary is increased significantly (10 to 30%) as the nanocrystalline grain size is decreased well below 30 nm. The solubility of tool material into the nanocrystalline grain boundary is two or three orders of magnitude greater than in the crystal lattice. Further the kinetics of diffusion in the grain boundary is seven or eight orders of magnitude greater than in the crystal lattice. Enhanced nanocrystalline grain boundary diffusion occurring in the interfacial layer at the tool-chip contact causes the accelerated chemical wear. Significant improvement in tool life could be achieved by engineering glassy oxide inclusions in steel, designed to self-lubricate the tool-chip interface in-situ at higher cutting speeds. Thus the control of sliding tribological condition at the tool-chip interface is key to suppress nanocrystalline layer formation at the tool-chip contact and hence prevent accelerated chemical tool wear. Sulfide inclusions are designed essentially to promote chip fracture. In addition, sulfide inclusions are designed to act as a diffusion barrier at the tool-chip interface. The application of inclusion engineering concepts to enhance the tool life in high speed machining will be demonstrated with a suitable case history.

Jan 1, 2006

By He Zhi-jun, Ning Zhe, Pang Qing-hai, Zhang Jun-hong, Zhan Wen-long

In this study, Raman spectroscopy was utilized to investigate the evolution of char structure in pulverized coal (PC) during microwave irradiation. The results indicated that though microwave treatment was carried out at low powers of 132W or 264W, significant variation in char structure was still observed. Char structure turned out to be more irregular firstly under microwave irradiation. However, char structure of superior regularity was obtained with the extension of irradiation time. It can be conclude that short time microwave treatment may facilitate the chemical activity of coal, while long time microwave irradiation on PC may deteriorate its combustion or pyrolysis property.

Jan 1, 2016

The kinetics of the oxidation of cyanide by manganese dioxide was studied using a rotation disc electrode system. The rate? of the half-cell reaction of cyanide oxidation is increased at higher hydroxide concentrations. An addition of copper up to 0.001 mole/l was found to enhance the diffusion current, especially at a high hydroxide concentration (0. 1M). A similar enhancement of the reaction rate is also achieved with nickel added at levels up to 0.01 mole/l. Manganese dioxide however requires a i:ow pH to achieve reasonable reduction rates. Leaching studies indicated that the initial reaction rate is strongly dependent on pH, initial concentration of cyanide. Using manganese dioxide cyanide could be oxidized at neutral pH&apos;s and ambient temperatures.

Jan 1, 1989

By K. A. Lewandowski

Agglomeration of ore can be used to immobilize fine particles during heap leaching by agglomerating them into granules. Without agglomeration, the fine ore particles can migrate within the heap, clogging flow channels and producing large areas where access of solution to the ore is very poor. The benefits of agglomeration are well-known in gold heap leaching operations, which can be effectively agglomerated using binders such as Portland cement due to the alkaline leaching solutions used. However, agglomeration has not been very effective in the heap leaching of copper ores, because these ores require an acidic leaching solution. Acid destroys the effectiveness of most binders, causing the agglomerates to disintegrate as soon as the leaching solution is applied. In order to gain the benefits of agglomeration in copper heap leaching, an economical, acid-resistant binder is needed. The two issues that needed to be addressed were: 1) Lack of effective methods for evaluating binder acid resistance before performing expensive, time-consuming, full-scale heap leaching tests, and 2) The vast majority of known binders react poorly to acid conditions, and so a basis was needed for determining which binders are most likely to be acid-resistant. In this paper, the development of two new tests for evaluating binder acid resistance in the laboratory are described. The ?soak test? determines the degree to which agglomerates disintegrate and release fines on contact with acidic solution, measuring the relative quantities of fines released by agglomerates made with different binders under controlled conditions, and serves as a rapid means for comparing large numbers of binders. The ?percolation test? measures several different parameters to determine how a binder is likely to perform in heap leaching: 1) the degree of ?slump? and compaction of agglomerates as they are wetted by acidic solutions; 2) the hydraulic conductivity of the agglomerate bed; 3) the migration of fines through the bed as the solution flows through it; and 4) the quantity of liquid retained in the agglomerates after they are drained. Using these tests, a broad spectrum of binders were examined. Soak testing determined that the most acid-resistant binders were nonionic polymers. Five of these binders were further evaluated using percolation testing.

Jan 1, 2006

By P Ridgeway, D Xie, M A. Somerville, S Jahanshahi, H Rogers, J G. Mathieson, Y Pan, N Haque, P Zulli, T E. Norgate, L Lu, A Deev

In 2006 the Australian steel industry and CSIRO initiated an R&D program to reduce the industry’s net greenhouse emission by at least 50%. Given that most of the CO2 emissions in steel production occur during the reduction of iron ore to hot metal through use of coal and coke, a key focus of this program has been to substitute these with renewable carbon (charcoal) sourced from sustainable sources such as plantations of biomass species. Another key component of the program has been to recover the waste heat from molten slags and produce a by-product that could be substituted for Portland cement. This paper provides an overview of the low-emission Integrated Steelmaking Process, progress made over the past seven years and the program’s future direction which includes proposed demonstrations of the technologies developed including large scale piloting and full scale plant trials.

Jan 1, 2014

By M. Rubinstein, N. C. Koon, B. N. Das, V. G. Harris

"Copper and gold - based alloys having giant magnetoresistance properties were produced by melt spinning from arc melted and cast rods. The ribbon width varied between 1 and 2 mm and the ribbon thicknesses were in the range of 30 to 50 11m. The uniform microstructure of the cast rods indicated the composition homogeneity in the starting material. The ribbons showed composition uniformity across the cross section from EDX analysis. However, the spun ribbon microstructure changed from a 'frozen in' region near the wheel side to a nanosize spherically precipitated phase towards the freely frozen surface. The evolution of the microstructure from the spun ribbon state to the annealed ones was studied by optical microscopy, SEM and TEM. The structural information of the spun and annealed specimens was obtained from X - ray, electron diffraction, electron microscopy and ferromagnetic resonance. Magnetoresistance was measured by the four point probe method.IntroductionRecently. Giant Magnetoresistance. GMR. has been observed in sputtered thin films alloys of Ag. Au and Cu with Co and Fe [1. 2. 3]. The sputtered films are produced by condensation of the alloys from the vapor phase. These Ag. Au and Cu alloys are miscible and homogeneous in the vapor and liquid phase (except Ag alloys which exhibit phase separation even in the liquid phase) but immiscible and heterogeneous in the solid phase. In our work we have produced thin ribbons of the Cu and Au alloys about 30 µm thick from the miscible state in liquid phase by rapid solidification melt spinning. The microstructural development of the ribbons was investigated in the as - spun condition and on annealing. The other properties such as magnetization. GMR and Mossbauer Spectroscopy were also investigated in the various microstructural conditions of the ribbons."

Jan 1, 1994

By Nathália M. Campelo, Alexandre P. Umpierre, Fabricio Machado

"The present work illustrates the reuse of macoporous anion exchange resins (employed for decolorization of solutions of organic substances such as sugar syrup and fruit juice concentrates in the soft-drink and beverages industries), based on crosslinked styrene-divinyl benzene copolymer (Sty-DVB) to the production of polymeric materials. Micro-sized particles of polystyrene and poly(styrene-ethyl acrylate) were obtained by mass-suspension sequential polymerization process. The proposed experimental technique was able to perform proper dispersion of the Sty-DVB in the thermoplastic matrix of polystyrene. The final material showed good thermal stability, showing degradation profile similar to that observed for the pure polystyrene. It was also noticed that polymer particles with spherical morphology can be obtained. In addition, the incorporation of ethyl acrylate monomer into the polystyrene chains minimizes the undesirable effect of fracture in polymeric particles, improving the mechanical and end-use properties of the final polymeric composite.IntroductionIn face of the industrial development, the development of techniques that are safer and less aggressive to the environment has become one of the main challenges in the industrial field. In this scenario, processes more efficient in terms of energy and raw materials can be regarded as an important requirement to minimize the production of waste. The reuse of waste becomes an attractive alternative for most industries engaged with sustainable and economic development.In this context, both the primary and the secondary mechanical recycling are potentially attractive because they allow for reuse of polymeric waste (post-industrial or post-consumer) as a source of raw material in the supply chain by using traditional methods of processing, so that the final materials can exhibit characteristics similar or superior to those observed in the virgins polymeric materials, considered as a starting product in the process of reuse of plastics [1-3]."

Jan 1, 2012

By D. J. Goodwill

BHP Copper operates a 3,400 tpd dry concentrate, single burner, Outokumpu flash smelting furnace (FSF) at their San Manuel copper smelter in Arizona. The very fine (-325 mesh), dry concentrate is fed to the burner from a 550 metric ton (nominal) capacity furnace feed bin via two drag chain feeders. During the 10-year history of the furnace, operations have been plagued by serious flooding problems. The fine concentrate sometimes becomes aerated during discharge from the bin and flows like a fluid at very high uncontrollable rates to the burner. This results in upset conditions at the concentrate burner leading to poor furnace metallurgy. This paper will examine the problems of uncontrolled feed from the furnace bin (i.e. flooding), and&apos; instantaneously feeding a flash smelting burner. It will show that a drag chain is a poor choice of feeder when high rates are needed, and that drag chains always produce a funnel flow pattern in a bin. BHP&apos;s drag chains cause narrow diameter, high velocity flow channels within the stored material. Consequently, there is insufficient residence: time for the concentrate to fully de-aerate before discharge, hence flooding occurs. In addition to the flooding problem, drag chains create a pulsating flow to the concentrate burner due to the tendency for material to slough off in discrete chunks at the discharge end of the slow moving chain conveyor. During the scheduled FSF rebuild in May 1999, BHP intends to remove the drag chains, modify the bin to a mass flow design and to use STAMET® multi-disc feeders to accurately and instantaneously control the rate of discharge from the bins. Air slides will be used&apos; to convey the concentrate to the burner.

Jan 1, 1999

By P. Wieser, D. Feke

"Priming of filters with small pores is influenced by the surface tension of the liquid metal and may be complicated by freezing • Freezing followed by melting has been observed experimentally. This process has been modeled on the basis of one dimensional heat flow by radiation to the filter and by conduction in the metal. Also considered are super-heat of the metal and the initial filter temperature. The results of the model provide useful guidelines for the application of filters. IntroductionFiltration has been recognized as a valuable method of refining by removing suspended phases from liquid metals or alloys. Woven fiberglass type fabrics and wire screens were used initially in the aluminum industry. With the introduction of the ceramic filters that exhibit improved inertness and refractoryness, filtration has been introduced to higher melting alloys including cast irons, superalloys, stainless steels, as well as low and medium carbon low alloy steels. A considerable literature is delveloping rapidly on the progress in applications and the advances in understanding the mechanisms and effectiveness of filtration processes (1-8).With the use of filtration for different alloy systems for the production of cast to shape parts a bewildering variety of gating system modifications has been developed (Figure 1) to accommodate the installation of filters in the mold. The modifications have two principal purposes: 1) the runner expansion is intended to compensate for the resistance to flow due to the filter and that of the captured inclusions, and 2) the metal reservoir upstream of the filter, provides a temporary by-pass which permits metal to flow across the filter and heat it until priming can be accomplished. priming of.filters by low and medium carbon steel is readily accomplished but, compared to such alloys as cast iron or 19 Cr-9Ni stainless steel, requires greater precautions to avoid failure to prime by excessive freezing on or inside the filter pores. This problem is further examined below:"

Jan 1, 1986

By Congcong Yang, Jian Pan, Deqing Zhu, Yang Zhong

A study of pelletization of one imported chromite concentrate with coarse site, poor ballability and refractory roasting performance was conducted in small scale tests, and high pressure grinding rollers (HPGR) was used to improve the pelletization. The mechanism of HPGR was revealed by means of SEM images and optical microscopy. Compared with the ball milling pretreatment, HPGR pretreatment can not only enhance the ballability of pellet feed but also drop the roasting temperature. Fired pellets, containing proper chemical compositions with high compressive strength of 2917N/pellet and good metallurgical performances, have been manufactured. The mechanism of HPGR reveals that chromite particle surface turns to more irregular after HPGR treatment and more new surface being formed because of more cracks, sharp corners and edges appearing, resulting in higher surface chemical activity, all of which improve the ballability of the chromite concentrate and contribute to the consolidation of fired pellets.

Jan 1, 2015