Search Documents

By N. Grosland, G. Kopp, T. Hunstad, D. Wilder, M. Contratto, S. Rahmatalla, T. Xia

Chronic whole-body vibration exposure, as expected in large construction and mining vehicles, has been associated with neck and back pain and injury.1 While work has been done towards gaining a better understanding of the relationship between vibration and shock and muscle activity of the back musculature2, relatively little information regarding the activity of neck, shoulder and upper arm muscles is known. Today’s equipment designs must conform to domestic and international standards, however these standards do not specifically address the vibration exposure in the head and upper quarter. Further it is not well known how the control configuration within a vehicle (e.g. steering wheel versus arm controls) influences muscle voluntary and reflex activity levels. Greater muscle activity may lead to greater muscle fatigue – which in turn may be associated with greater risk of injury.2 Thus, muscle contractions needed to maintain static postures as well as those resulting reflexively should be considered during an analysis of seating position. Unfortunately, little is known regarding the influence of arm position on head and neck muscle function. The purpose of this study was to investigate the relative muscle activities of 5 neck, shoulder, and upper arm muscles during riding simulations of large construction equipment, using three different arm control options. Methods Five typical heavy equipment ride files were “played back” through a man-rated Servo Test 6-degree of freedom (dof) vibration system. Each ride was repeated using 3 seat and control configurations (steering wheel (SW), floor mounted arm-rest controls (FM), seat mounted arm-rest controls (SM)). Two trials were performed for each ride and seat control combination (each trial: 60 sec of 6-dof and 60 sec of vertical vibration). Five channels of surface electromyography (EMG) of the right-side cervical erector spinae muscles (neck extensors), sternocleidomastoid (neck flexor), upper trapezius (shoulder elevator), biceps brachii (elbow flexor) and triceps brachii (elbow extensor) muscles were collected throughout each ride (~ 2min) using pre-amplified (10x), 1 cm silver bar electrodes, with 1 cm fixed inter-electrode distances (Delsys, Inc). Further analog amplification was set at 10k (1k for one subject), and sampled at 1000Hz using a 12-bit DAQ card and Labview 7.1 software (National Instruments). A total of 7 right-handed male subjects were tested, but only 5 had complete EMG data sets to analyze for this sub-study. EMG was analyzed using root mean square (RMS, in mV) of 20 ms moving windows, and then averaged across the entire trial for a measure of mean total muscle activity (voluntary and reflexive). The muscle activity to maintain the static posture was estimated as the mean RMS EMG over a 1 sec interval just prior to and/or after completion of the ride. Repeated Measures ANOVAs were used to test for with-in subject differences using a = 0.05.

Jan 6, 2006

Jan 1, 1968

By Richard S. Olsen

Prior work by the Bureau of Mines demonstrated a feed preparation method that eliminates the formation of slime during leaching of calcined kaolinitic clay and makes leached residues fast settling and easy to filter. Nitric acid leaching rates determined for calcined kaolinitic clay prepared by this method were found to correspond to a zero-order reaction model for both batch and continuous, stirred-tank leach-ing. A rate constant of 0.136 min-1 was determined. Separation of solid residues from the reacted slurry was examined, and filtration rates were determined. Permeabilities of the flocculated, leached residues were around 51 darcys, or 5.0 x 10-7 cm2 for laminar flow through 4-ft-deep beds.

Jan 1, 1983

By T. Yegulalp, R. Farrauto, A. Belova, M. Castaldi

Calcium oxide, with its ability to capture and store carbon dioxide, is emerging to become an important tool in carbon management. Calcium oxide can be used reversibly to capture carbon dioxide in situ and then be regenerated to produce a pure stream of carbon dioxide ready for sequestration; the Zero Emission Coal Alliance technology utilizes this property of calcium oxide to generate emissions-free electric power from coal. The reaction of calcium oxide with carbon dioxide resulting in thermodynamically stable carbonate is well understood; however, the efficiency of this reaction is limited by the diffusion of gases through bulk calcium oxide and through a layer of carbonate formed on the surface. In addition, the regeneration of calcium oxide is an endothermic reaction and is favored at high temperatures. The purpose of this paper is twofold: first, to address the diffusion limitation, a thin layer of calcium oxide, supported on a high surface area material, is studied thermogravimetrically to demonstrate the physical adsorption of carbon dioxide on calcium oxide. The adsorption is to take place at temperatures lower than required to form calcium carbonate.

Jan 1, 2007

By T. R. Roy

"This paper presents an objective model for the estimation of fire risk potential of an underground coal mine panel by the bord-and-pillar method of mining where extraction is carried out by depillaring with caving. The fire risk rating procedure for the estimation of fire risk potential involved in the panel is described in detail. The model developed thereof is tested with the field data collected from different collieries across the country along with the laboratory data for critical assessment of fitness of the model. Some results showing the validity of the model are also cited here. Introduction The occurrence of fire in underground coal mine panels is quite common in India and elsewhere. These fires cause extensive loss of resources.Although substantial work has already been done by different research organizations, the problem has not been fully eliminated.The causes of panel fires depend not only on the spontaneous heating susceptibility of coal, but also on the extraneous conditions created in the panel due to the mining operations. From the studies done so far by various organizations, it is apparent that two types of parameters associated with spontaneous heating of a coal mine panel exist: intrinsic and extrinsic. Parameters related to the nature of coal, i.e., its physicochemical characteristics, petrographic distribution and mineral make-up are intrinsic, while the extrinsic parameters are related to the atmospheric, geological and mining conditions such as scope of leakage of air into the panel, wetness of mines, heat dissipation capacity of the panel, gassiness of seam, geological disturbances, method of extraction, size of panel, etc.Banerjee (1982) identified twenty-two mine parameters such as spontaneous heating susceptibility of coal, method of mining, geological disturbances, quality of overburden, degree of consolidation of coal mass, scope of accumulation of coal fines, etc. that can influence spontaneous heating in underground mines. He used the terms “high” and “low” for fire risk rating of each of these parameters. Since this approach is oversimplified, it can not determine the exact fire risk potential of an underground working."

Jan 1, 2003

By Otto Sandoval Zea

En la actualidad, existen equipos que analizan los daños colaterales producidos por la voladura como el uso de sismógrafos, los que son aplicados para el control de los limites permisibles de vibración en construcciones superficiales, de forma que permiten realizar análisis de vibración en condiciones subterráneas (Minas) y establecer parámetros que generen un mejor diseño de excavación en el avance y producción. En esta perspectiva, el presente texto para predecir el daño generado por los explosivos y la reducción de los mismos, emplea el análisis vibracional, donde se determina un comportamiento de atenuación de la velocidad vibracional de partículas en función a la distancia y la carga operante* representado por una curva exponencial denominado “Ley de Atenuación de Vibración de Partícula”, que difiere según la calidad del macizo rocoso y la potencia del explosivo empleado.

Sep 14, 2009

Ground and air vibrations induced by large surface blasts have been monitored. These field results, as well as a large number of published results, have been used to assess the performance of existing predictors and for the development of improved prediction methods. Field monitoring has been performed, with four seismographs giving complete wave records, at limestone quarries, coal strip mines and an open pit copper mine. Conventional analysis includes least square fitting of peak particle velocities and peak air overpressures with scaled distance formulations. Frequency content has been analyzed, and correlated with blast design (detonation sequence). Two new methods have been developed for predicting ground vibrations induced by blasting. The proposed analytical predictor accounts explicitly for inelastic attenuation and geometrical spreading, and calculates the peak particle velocity as a function of charge weight and distance. Statistical analysis of case studies confirms the consistent improvement over conventional scaled distance predictors. The second new predictor is a computer program simulating blasts, including blast geometry, charge distribution and detonation sequence, and simulating propagation of individual pulses to any point of interest, where effects are summed. A complete blast vibration results, allowing prediction of frequency content and duration as well as peak velocities.

Jan 1, 1983

By A. H. Burns

"Regenerative and recuperative burner systems require advanced combustion techniques to minimize NOx emissions. Various methods of pollutant minimization and furnace design considerations are described. Cited examples are a large high temperature furnace and a small Zinc vaporizing furnace. The concept of total carbon footprint is introduced. The application of Biomass combustion as an effective method of cost and green-house gas (GHG) reduction is discussed. Practical considerations of scale, location and process limitations are discussed. Two examples of biomass fired equipment are cited. Ideal sites have large biomass resources available locally. Processed biomass fuels will be an important substitute for fossil fuel. INTRODUCTIONIn 1992, I presented a paper entitled Combustion Strategies In The Modern Industrial Environment (1992). At that time an abundant supply of cheap fossil fuel made many of the measures I talked about difficult to justify for anything but new equipment.Since 1992 we, as a society, have demonstrated an ability to accelerate the pace of industrial and societal change. The term industrial revolution applied to this age of incessant change is completely meaningless, implying a discrete moment in historical time. What our society has built is a system capable of unfettered, continuous and accelerating technological change. With this change comes an increasing demand for energy and materials.This year is the anniversary of the Titanic disaster, a moment in time when technological certainty met the caprice of nature and gave us a brutal reminder of what can happen to us if we underestimate that power (Mowbray, 1912). In the intervening interval we have regained the technological arrogance that was lost in 1912 bringing us back to the problems of climate change and the need for sustainable industrial activities.We use advanced mathematics to describe many complex systems, sometimes with disastrous results. For example there has been a recent attempt to model the global economy as a completely deterministic system. This premise is flawed at its foundation as human nature and emotion are indeterminate constants in the equations, yielding probabilistic solutions at best. As engineers we are all familiar with stiff problems. The solution to such a problem is meaningless and we have all had the misfortune to live through and rue the effects of that miscalculation over the last few years."

Jan 1, 2012

By Antonio Mendoza

El presente texto describe el sistema de manejo de agua y aire, las actividades integradoras, preventivas, de análisis y ejecución realizadas para describir la respuesta a los retos del futuro inmediato para alcanzar los objetivos ambientales en la mina Antamina.

Jan 1, 2012

By Ellsworth Y. Dougherty, Edwards F. Fitzhugh

"INTRODUCTION During the summer of 1945 the Bureau of Mines made approximately 200 miles of reconnaissance magnetic surveys in north-central Mirnesota. The survey started near the western end of the Mesabi Iron Range and extended into the area to the southwest, west, and northwest and also southward to the-northern limits of the Cuyuna Iron Range. The purpose of the survey was to data to assist exploration for iron ore in the region through:1. Supplying a relatively unit form network of traverses, by which and future surveys of localities in the urea ray be correlated. Suggesting localities in which more detailed magnetic surveys may be justified, and, Disclosing localities in which there is lass hope of obtaining significant results from further magnetic surveys.The instrument used was a Hotchkiss Superdip, and traverses for calibration and comparison were run with a Schmidt-type magnetometer. Field observations and work directly related thereto were carried out under contract by E. J. Lang-year Co., Minneapolis. Engineers of the Bureau of Mines planned, directed, and reviewed the survey."

Aug 1, 1946

By V. E. Dawson

Brake testing of large mining trucks was initiated in British. Columbia in 1969 following an accident involving the failure of the service brakes of a l00-ton electric-drive truck. Some selected results of the 1976 brake test program are presented and discussed ?in this paper . The tests were conducted on end- dump trucks having load capacities ranging from 85 to 235 tons. All tests were made with the vehicles fully loaded operating on downhill grades varying from 8 to 10 %. Stopping distances were measured from initial speeds varying between 10 and 39 mph. The results are adequate, in most cases, to determine the "ultimate" capabilities of the service brakes of varying models and sizes of haulage trucks operating in British Columbia mines.

Jan 1, 1977

By Suresh Menon

The explosive industry in India has passed through various stages - from a period of total dependency to a period of self sufficiency and now, is saddled with large spare capacity. The last decade and a half saw the emergence of small scale manufacturers, which until then was thriving on International technology.

Jan 1, 1998

By Hisataka Sakakibara

Although the pathophysiology of vibration-induced white finger (VWF) is still under discussion, evidence has been accumulated to understand the underlying mechanism. VWF is pathophysiologically characterized by an enhanced vasospastic response to cold, which can result from an imbalance between vasoconstriction and vasodilation in the digital arteries in response to cold (i.e., vasoconstriction-dominant). The imbalance is supposed to be due to faults in vascular vessels and sympathetically mediated vascular tone. Enhanced vasospastic response to cold Narrowing of arterial lumen with medial smooth muscle hypertrophy. Possible functional factors for enhanced vasoconstriction • Increased sympathetic nervous activity to cold (e.g., norepinephrine) • Increased release of endothelin-1 (ET-1; an endothelial-dependent vasoconstrictor) from the endothelium • Increased reactivity of alpha2-adrenoreceptors to cold Possible functional factors for decreased vasodilation • Decreased release of nitric oxide (NO; an endothelial-dependent vasodilator) from the endothelium • Decreased release of calcitonin gene-related peptide (CGRP; a vasodilatory neuropeptide) from sensory afferents The question is how their interrelations or imbalances among them are Vibration and arterial damage The next question is, how does hand-arm vibration exposure induce such pathophysiological changes in VWF patients? Recent morphological evidence from animal experiments shows that vibration acceleration stress (including shear stress) and smooth muscle contraction contribute to arterial damage of smooth muscle and endothelial cells. The vibration-induced arterial damage is frequency-amplitude-dependent.

Jan 6, 2006

By D. N. Adams, M. M. Wong, M. J. Robison

Islais Creek Contract E, a transport/storage tunnel in San Francisco, was visited on a fieldtrip during construction by delegates to the 1995 RETC. This paper is a follow-up to that fieldtrip. The project’s two tunnels are 3.7 m and 3.2 m finished diameter, 155 m and 77 m long, respectively. The contractor used 1,000 overlapping jet grout columns to pre-treat the weak Bay Mud along the tunnel alignments, then mined them with an open faced tunnel shield, eliminating the need for compressed air tunneling. This paper documents the jet grouting program and the tunneling operation used on the project.

Jan 1, 1997

INTRODUCTION This paper was originally presented at the Platinum Adding Value Conference, held at Sun City from the 4th to 6th October 2004. Narrow reef mining may not be applicable to the base metal operations in Zambia, however, it is considered that the methodology used is equally appropriate to the development of technology and mining methods in mining environments other than narrow reef mining. The purpose of this paper is to explore the integration of technology and stoping systems. For the last hundred years the South African narrow reef mining industry has battled to control working costs in a labour intensive industry. It is only through the application of appropriate technology that change will occur. Stoping systems, because it is the stoping method and methodology that is at the heart of the mining system. Introduce a different technology that results in a more efficient stoping system and the mining system will look after itself. The technology applied to stoping in narrow reef mining, over the last 100 years, can be categorised as follows: ? The introduction of pneumatic rockdrills early this century. The cumbersome rig mounted units being replaced by smaller, lighter, hand held units that were then made easier to use with the addition of an air leg. (The so called Swedish method of mining.) As late as the early 1970s some drilling was still being carried out without the assistance of an air leg. ? Scraper winches to replace gravity and shovels to move rock both in the face and the gullies were first introduced in the late 1920s. ? Hydraulic props installed close to the face and capable of applying force against the hangingwall as well as yielding in a controlled manner under dynamic load arrived in the 1960s. In many instances these have now been replaced by yielding elongates fitted with water hydraulic tensioning devices. ? Some people argue that the introduction of tungsten carbide inserts, to improve drilling, was equally important.

Jan 1, 2005

By Fred W. Brackebush

In underground stopes that require more than minimal support, backfill is almost universally used. The term cut and fill stopingis used in a broad sense in this section, which describes underground mining methods requiring support. Support in stopes can be classified as local or short-term and general or long-term. Local support for the back of a stope, for example, can be accomplished with rock bolts or timber stulls. General support for the walls of the stope is provided by backfill. Local support provides a safe working place for the stope miners. General support, provided by backfill, preserves the access way to the stope and prevents large scale dilution of ore. Supported methods are a set of cut and fill stoping methods using backfill for general support and various local support methods. his section is subdivided into three chapters: 19.1 Cut and Fill Mining 19.2 Excavation Techniques 19.3 Backfilling Methods

Jan 1, 2008

By J. H. Schuenemeyer

Uncertainty estimates on coal resources were computed as part of the U.S. Geological Survey’s National Coal Resource Assessment study of more than 60 coal beds and zones in the Appalachian Basin, the Colorado Plateau, the Gulf Coast, the Illinois Basin, and the Northern Rocky Mountains and Great Plains. The estimates were made to provide zone specific measures of uncertainty on the historical categories of geological assurance, namely measured, indicated, inferred and hypothetical. Previous estimates were based solely upon distance from a drill hole. These new estimates incorporate site-specific variability and spatial correlation and indicate that there is considerable difference in variability within and between regions. Uncertainty estimates for the measured category are discussed in this paper.

Jan 1, 2001

By Rodney D. Lamond

The need for blast vibration monitoring can be attributed to a combination of three factors: Structural damage, Blast design and Human annoyance. Traditionally, vibration damage criteria are prescribed in terms of peak particle velocity (PPV), as measured or predicted in the ground surrounding a blast. The PPV in the vicinity of a blasthole is strongly influenced by the quantity of the explosive per delay. In general, the existing prediction models give reliable results but fall short of addressing the change in PPV when the charge is decoupled and/or distributed.

Jan 1, 1995

By Marco Vinicio Guamán Alarcón

O modelo do Gradiente de Tensão (SG) e a Teoria da Distância Crítica (TCD) são usados para estimar o limite de fadiga de corpos de prova com entalhes alongados, e essas estimativas são testadas em C(T) modificados submetidos a tensões cíclicas de amplitude constante com uma razão de tensão R = 0.1. Os valores medidos são comparados com as previsões feitas por ambos os modelos. As previsões do modelo SG estiveram mais de acordo com os resultados experimentais. Também foi demonstrado que o modelo SG é quase equivalente à TCD no caso de entalhes com raios grandes, quando a TCD usa o método do ponto. Para o caso de entalhes afiados, os valores dos limites de fadiga previstos pela TCD são mais conservativos que os previstos pelo modelo SG.

Aug 17, 2017

By YUSONG MIAO, DI WU, XIANRONG YAN, YIPING ZHANG, JIE LIN, KEBIN LI

Rock fragmentation size distribution is often used as an important index to account for the blasting effect because it directly affects the subsequent loading, transportation, and secondary crushing. Due to the mismatching of explosive and rock wave impedance, high boulder yield often occurs which affects the blasting effect. In this study, methods of measuring rock acoustic impedance, rock strength point loading, and detonation wave velocity have been used to obtain more accurate input parameters. Then, in the watershed image segmentation technique, the Gates-Gaudin-Schuhmann and Rosin-Rammler distribution functions have been used to analyze and quantitatively describe the rock fragmentation size distribution in the existing muck-pile. Finally, taking the rock properties, explosive performance, blasting parameters, and system characteristic variable into consideration, support vector machine (SVM) regression model has been analyzed on the learning and prediction of samples. The results show that SVM has a good prediction accuracy, high precision, and strong generalization ability. The optimized matching coefficient of rock and explosive wave impedance K ranges from 2.50 to 2.58 times. This study has developed a series of simple, accurate methods for rock properties analysis, detonation wave velocity measurement, and muck-pile model image processing, and a basis for predicting and evaluating rock fragmentation size distribution and optimizing the matching coefficient before carrying out a blasting operation.

Jan 22, 2021