Search Documents

By P. H. Reynolds, S. Liaghat, A. Zarasvandi

"Darreh-Zerreshk and Ali-Abad are two relatively small porphyry copper-type deposits in Yazd Province in central Iran. They are located within the central Iranian volcano-plutonic belt, formed above the collisional convergent margin of the Iranian lithospheric plate from the late Eocene to the Miocene. This paper discusses the geochemical characteristics of the igneous rocks, and 40Ar/39Ar geochronology of plutons and alteration phases associated with the Darreh-Zerreshk and Ali-Abad deposits. The deposits are spatially associated with igneous complexes that consist of older and barren granites intruded by intermediate-composition granitoids, which are the carriers of Cu mineralization. The granites have relatively high content of Nb, Y, and K, a prominent negative Eu anomaly, and were probably derived from melting of, or contamination of mantle-derived magmas by, continental crust. Porphyritic diorites, quartz monzodiorites, and granodiorites show enrichment in light rare earth and large-ion lithophile elements, depletion in middle rare earth elements, and have no negative Eu anomaly. These intermediate-composition granitoids were derived from melting of the upper mantle or lower crust, and their differentiation was controlled partly by fractionation of hornblende. A pilot K/Ar whole-rock dating study suggests that the pre-ore granites were emplaced in the Oligocene. Dating by the 40Ar/39Ar method of nine samples of secondary biotite and sericitized rocks from drillcore within the mineralized and altered zones in both deposits yielded a well-defined age of ca. 16 Ma. This date is interpreted to be the time of hydrothermal alteration and of porphyry copper type mineralization in this part of Iran."

Jan 1, 2007

By Gerald L. Stolarczyk

Safe and efficient coal extraction requires advanced radar subsystems that can be mounted on cutting drums of coal cutting machines. A look-ahead radar (LAR) must solve the radio geophysics problem of transmitting an electromagnetic (EM) wave through at least 20 feet (6.1 meters) of coal to an air- or water-filled void. The reflected EM wave must be processed in the radar electronics to determine the physical distance to the void. Horizon sensing enables selective cutting near the undulating sedimentary rock boundaries of the coal bed to address coal quality and ground control issues. Both sensors require subsystems for dynamic electric power generation, real-time measurement of drum rotation angle, detection of reflected EM waves, and processing to determine distance through coal and RF modem transmission of measured data to the mining machine. This paper describes the development of the subsystems and field test results.

Jan 1, 2006

Process Simulation and Plant Design of a Mineral Selective Magnetising Flash Roasting Plant Using Neutrons

Sep 13, 2010

By Lisa A. McDonald

The environmental compliance process affects all aspects of hardrock-mining operations, from exploration through post-closure. The primary components of the environmental compliance process are requirements under the National Environmental Protection Act of 1969 (NEPA) and the permitting requirements associated with various other federal, state and local laws. This study considers the Greens Creek Mine and the development of two other projects (Alaska-Juneau & Kensington). These mines were used as the foundation for a case study of the impacts of the environmental compliance process on hardrock-mining activity in Southeast Alaska. The case study presents the institutional and legal requirements, followed by a discussion of the impact of this process on the production and timing of the three mines. The results of this preliminary study reveal some interesting findings, some expected and others unexpected, regarding the impact of the permitting process on the exploration, development and (proposed) operation of the three mining projects in the Juneau area. Determining the cost of compliance with these requirements is an important step in evaluating the appropriate course of action to protecting the environment while providing the necessary raw materials needed for society. This preliminary study highlights the initial starting point for such an analysis.

Jan 1, 1992

A variety of environmental financial assurance instruments are in use across the globe. This paper reviews some of the more common forms currently used in New Zealand, Canada, USA and Australia. In order to be effective, the form of assurance instrument selected needs to be aligned with a countryÆs specific environmental objectives, geography and political climates and also allow for a healthy investment climate. Industry and Government both have a strong interest in ensuring financial assurance criteria meet these objectives.   Recently Golder Associates have been involved in financial assurance assessments for various mining and quarrying companies across the South Island. Multiple stakeholders and regulatory agencies can make the setting of effective and fair financial assurance criteria a complex exercise for both regulatory agencies and industry.  The author relates experience gained in assessing financial assurance under current New Zealand legislation (RMA, 1991), effectively dealing with issues such as ôdouble bondingö and overviews potential approaches to dealing with transitional issues for historic and existing operating mine sites.

Jan 1, 2006

By M. Machikicho, N. R. Shoko, J. Chirasha

Keywords: Pyrometallurgy, furnace, ferrochromium, alloys, Zimbabwe Zimbabwe Alloys was founded in 1949 by a consortium led by the John Brown Group. It was the first ferrochrome plant in Africa. The establishment of the refinery was necessitated by an increase in world stainless steel demand and the need to reduce cost by shipping alloy rather than chrome ore. The location of the refinery in Gweru was influenced by a number of factors, not least of which were the abundance of chrome ore deposits, access to inexpensive power from Kariba, the availability of reductant coke from Hwange, accessibility to ports (as the town was well served with rail and road networks second to none in the country), and of course cheaper labour costs. The production of Low Carbon Ferrochrome (LCFeCr) was commissioned in 1953 and produced from an Open Arc Furnace with a Submerged Arc Furnace producing Ferrosilicon Chrome (FeSiCr) that is used as a reductant in the production of LCFeCr. An experimental furnace was commissioned in 1958 to help with efficiency and control on larger furnaces. A second Submerged Furnace was commissioned in 1963. Three other Submerged Arc Furnaces were built between 1967 and 1974. Several mines were acquired between 1974 and 1984, as a strategic move to ensure the growth of the refinery. A briquetting plant was commissioned in 1977, enabling the use of friable ores to enhance the capacity of ore supplies and ore cost management. A plant to recover alloy from slag was established in 1994 to capitalize on market demand without large capital outlay that would be required to build other furnaces to increase capacity. Zimbabwe Alloys has created employment opportunities throughout the years. There have been direct employment opportunities at both the refinery and the mining divisions. With time, indirect employment was realised both upstream and downstream of the refining process, enhancing the livelihood of numerous people. Zimbabwe Alloys' involvement with various labour skills has, of necessity, enabled it to develop a culture of safety at work, home, and play. Zimbabwe Alloys has contributed to society by participating and funding various local initiatives primarily to impact positively on societal needs. The latest development was in 1996, when Zimbabwe Alloys entered into a Technical Transfer Agreement with Japan Metals and Chemicals to improve the efficiencies and hence the profitability of the LCFeCr production process. A significant quantity of various alloys has been produced since inception, and significant foreign currency has been earned for the country. This was in spite of challenges that included the cyclic nature of market prices, the upheavals of sanctions affecting the macro-economic environment, and the challenges related to the deteriorating grade of chrome ore and reductant coke.

Jan 1, 2006

By M. Wong-Kian, L. A. Cornish, A. van Bennekom

Samples of four different satellite materials were prepared by either hot isostatic pressing (HIP) of the powder or tungsten inert-gas welding of rod onto a 316 L stainless-steel substrate. The samples were subjected to a series of comparative erosion corrosion tests, and generally the Hipped samples experienced between 13 and 24 per cent less loss in mass than the equivalent welded alloys. Resistance to erosion corrosion increased with increasing carbon, chromium, and tungsten contents. Metallographic studies indicated the differences in carbide content between the different satellite materials, and the differences in morphology between the Hipped and welded samples. Finer and more homogeneous microstructures were

Jan 1, 1995

By Victor R. Spironello

Applications of three experimental design techniques to smelting operations are explained. The report describes a factorial design using three variables at two levels, a fractional factorial design which investigates seven variables, and response-surface methodology for optimization of electric- furnace smelting processes. These methods may be applied with a minimum of trials and at little expense. Further, the writer knows of no reasons why the same methods could not be applied to other operations as well, such as steelmaking.

Jan 1, 1970

By John L. Edwards, Anthony T. Iannacchione

There has been a persistent need to forecast roof falls so that miner’s exposure to hazardous underground environments can be minimized. Several monitoring techniques have been developed and are used today with varying levels of acceptance in the mining industry. This paper examines the potential for monitoring microseismic emissions activity as a means of forecasting roof falls. The use of this activity to forecast roof falls has drawn only limited attention, resulting in a lack of published field performance data. This deficiency is being partially addressed by analyzing data obtained during longwall mining at Moonee Colliery in 1998. The Moonee data base contains a wealth of information concerning roof fall forecast parameters and the seismic alarm criteria used to develop these forecasts. Four seismic alarm criteria were developed and used by Moonee with varying degrees of success. Roof falls were forecasted 73% of the time with average forecast times of 54 minutes. Ninety percent of the predicted roof falls had a warning time, i.e., the time between warning and roof fall event, of greater than 1 minute. The fraction of forecasted roof falls decayed logarithmically as a function of warning time, until only 20% of events were predicted more than 100 minutes prior to roof falls. False alarms occurred in 50% of the warnings. Many of the false alarms were quickly followed by a cessation in mining which could have temporarily halted the on-going failure process. If mining had continued immediately after the false alarms, a roof fall may have occurred soon after. The microseismic activity collected from Moonee Colliery demonstrates that techniques to forecast roof rock instabilities in underground mines are possible.

By Kimio Itagaki, Torn Matsumoto, Makoto Ohtsuka, Kentarou Harada

"The structure and hydrogen-absorption properties of LaNis thin films were investigated in the present study. LaNis thin films were prepared by a sputtering method with a radio-frequency power, Ws, of 50 -400 Wat substrate temperature, Ts, of323 -573 K. Nickel content of the films decreased with increasing Ws, however, there was no dependence on Ts. At low Ws and low Ts, amorphous films were deposited. In other conditions, the films were polycrystalline. The films prepared at high Ws and low Ts, or at low Ws and high Ts, exhibited only a (h k · 0) peak in the X-ray diffraction profiles. This indicates that the c-axis of crystalline films was oriented parallel to the substrate plane. At high Ws and high Ts, the films with columnar structure were obtained. Hydrogen-absorption capacity of the thin films increased with increasing Ws. The pressure plateau did not appear on the pressure-composition isotherms. The films deposited at high Ts represented a higher equilibrium pressure.IntroductionThin films of hydrogen storage alloys can be applied for an electrode of rechargeable battery or fuel cell, a filter for H1 purification and various kind of sensor. Some studies on the preparation of the thin films of LaNi5 intermetallic compound, which is a typical hydrogen storage material, have been done hitherto. Adachi et al. , 2) and Sakaguchi et al. 3) prepared amorphous and crystalline LaNi5 thin films using flash evaporation of alloy powders and measured the pressure-composition isotherm for the prepared film utilizing a quartz crystal mass monitoring (QC:MM) method. It was found that the prepared amorphous film absorbed hydrogen without disintegrating into the powders and the hydrogen-absorption capacity of the films increased with the degree of crystallinity. Sakai et al. 4) reported that the maximum hydrogen storage capacities of amorphous and crystalline LaNi5 thin films, fabricated by a RF sputtering method using combination targets, were about 40 mA h g-1 (LaNisHo.7) and 160 mA h g-1 (LaNi5H2.6), respectively. Uchida et al. 5, 6) prepared LaNi5 thin films using flash evaporation of alloy powders and measured volumetrically the pressure-composition isotherm for the prepared film. It was reported that the hydrogen-absorption capacity of the films changed by the annealing treatment."

Jan 1, 1998

Jan 1, 1962

By C. S. Gibson

"MOST of the mines in the Province of Ontario in Canada are multi-level operations in steeply dipping veins; yet there is an appreciable number whose de-posits are relatively flat-lying, ranging up to 45° inclination.The veins vary in width up to several hundred feet and may or may not be branching systems. The depths of mines range from a few hundred to 8,000 feet, approximately. The primary products of the underground group are asbestos, gold, silver, cobalt, copper, nickel, iron, uranium, talc, fluorspar, gyp-sum and salt.There are a few open-pit mines. The majority are temporary in type because, as the outcrops are removed, mining is continued be-low surface. Primary products of the open pits are copper, nickel, iron, magnesium and nepheline syenite.The industry as a whole employs about 50,000 persons, approximately 60 per •cent of whom have dust-exposure occupations. The definition of a dust-exposure occupation and the requirements for •dealing with same are set forth in The Mining Act of Ontario.Results of extensive and continuing studies on the incidence and progression of silicosis have been reported periodically for years past, in annual reports of the Mines Accident Prevention Association of Ontario and in papers presented at Conferences sponsored by Mcintyre Research Foundation of Toronto, all of which have been published. The information provided therein proves the effectiveness of the means being used to prevent silicosis and allied disorders."

Jan 1, 1960

The steps for the beneficiation of iron ores differ from ore to ore, depending on the mineralogical phases of the particular iron ore and the nature of the association of the gangue minerals with iron oxide in that ore. The extent to which the beneficiation can be undertaken economically depends both on the amount and the nature of the gangue. The analysis of the phases present in an orebody optimises the mining and process operations (separation, beneficiation, sintering, etc).X-ray diffraction (XRD) provides qualitative and quantitative information about the main ore phases as well as the gangue mineralogy and the amorphous content present in a sample. In addition, modern quantification methods such as Rietveld refinement allow the calculation of the distribution of elements in solid solutions such the substitution of Fe with Al in goethite or hematite.The use of high speed detectors has made XRD an important tool for grade and process control. Finger printing of XRD data can facilitate multi-dimensional mapping of ore deposits and drill cores, identifying regions of favourable mineral compositions. Grade control using XRD can be completely automated and controlled remotely.The two case studies in this paper demonstrate how XRD and finger printing can be used for grade control, process optimisation and quality control of a goethitic and a magnetitic iron ore. The enormous potential of XRD as an inexpensive, reliable tool, useful in the characterisation of iron ores will be demonstrated.CITATION:K÷nig, U, 2013. Application of x-ray diffraction to iron ores - potential implications for grade control and downstream processing, in Proceedings Iron Ore 2013 , pp 275-280 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

Laboratory and pilot plant investigations aimed at recovering gold as an electroformed sheet from gold eluate and gold leach solutions and slurries are discussed. The electrolytic test work undertaken makes use of high surface area electrodes, in particular nickel-chrome foam metal and activated carbon, as well as ultrasonic activation. The process involves initial gold electrowinning (or adsorption onto activated carbon), followed by gold electroforming, both operations being carried out in a specially designed reactor. The pilot plant work mainly involved the treatment of gold eluate solutions from a South African gold mine containing 600 mg/L Au: some tests were also carried out on gold leach solutions containing 6 mg/L Au. In the former case, very efficient gold extraction onto the foam metal cathode was achieved using electrolysis combined with ultrasonics. The polarity of the gold-loaded cathode was then reversed and, using a replacement electroforming electrolyte, gold was electroformed in situ onto a polished stainless steel mandrel, from which gold sheet was subsequently removed. In the case of leach solutions, pilot plant tests confirmed laboratory findings that in the presence of calcium (resulting from the lime used during the leaching process) no electrowinning is possible. Laboratory tests showed, however, that when sodium (in the form of NaOH or Na2CO3) is added to the leach solution, electrowinning can indeed take place. Alternatively, if a special activated carbon electrode is used (without current), the non-ionic calcium aurocyanide complex is adsorbed on to the activated carbon. When a gold-loaded activated carbon electrode is made anodic in a gold electroforming electrolyte, gold electroforming is feasible, although the efficiency is very low. The possible implications of these developments for gold recovery are further examined.

Jan 1, 2007

By K. K. Kelley

The collection and correlation of thermodynamic data concerning substances of metallurgical interest have constituted one of the major activities of the Pacific Experiment Station of the Bureau of Mines, at Berkeley, Calif., for the past several years. Earlier bulletins (32, 33, 34, 36, 36, 37, 38) s in this series are entitled: (1) Contributions to the Data on Theoretical Metallurgy. I. The Entropies of Inorganic Substances; (2) Contributions to the Data on Theoretical Metallurgy. II. High-Temperature Specific-Heat Equations for Inorganic Substances; (3) Contributions to the Data on Theoretical Metallurgy. III. The Free Energies of Vaporization and Vapor Pressures of In¬ organic Substances; (4) Contributions to the Data on Theoretical Metallurgy. IV. Metal Carbonates--Correlations and Applications of Thermodynamic Properties; (5) Contributions to the Data on Theoretical Metallurgy. V. Heats of Fusion of Inorganic Substances; (6) Contributions to the Data on Theoretical Metallurgy. VI. A Revision of the Entropies of Inorganic Substances-1935; and (7) Contributions to the Data on Theoretical Metallurgy. VII. The Thermodynamic Properties of Sulphur and its Inorganic Compounds. The present paper collects and discusses thermodynamic data relating to metal carbides and nitrides, with the view of obtaining usable heat and free energy of formation relationships. Pertinent data on both classes of substances are difficult to obtain experimentally and consequently are extremely rare; it is therefore necessary in many cases, if equations are to be derived, to introduce certain approximations and assumptions. Lack of adequate means of checking results by utilizing data of different types, such as was done frequently in the bulletins dealing with carbonates and sulphates, are readily apparent to anyone who has made even a cursory examination of the available information. Consequently, some of the relationships derived undoubtedly will be found to be inaccurate when more or better data become available. Nevertheless, in view of the importance of some of these substances, it appears worth while to consider the information available at present and to attempt the formulation of as complete a

Jan 1, 1937

A computer system for calculating the illumination on coal mine surfaces due to machine-mounted lights is described. Utilizing numerical models of mining machinery and measured data on luminaire output characteristics, the program computes the ft-candle levels incident on the mine entry surfaces for any desired machine/luminaire/ entry configuration. Shadowing effects of the machine are taken into account. Results are provided at 2 ft. intervals on the face, left and right walls, floor and roof. The system operates, interactively from a Tektronix 4014 graphics terminal which handles all input/output functions. The software is installed on a Cyber 74 computer that communicates with the terminal via telephone line.

Jan 1, 1978

By Euler De Souza

This paper presents a study conducted to assess sillmat behaviour during undercut mining and to provide a comprehensive understanding of the effects of arching and sillmat thickness on stability. The design study investigated the effects of such parameters as stope width and height, closure strains, orebody geometry and inclination, wall roughness, fill properties and cure time on the stability of cemented sillmat during undercut mining. Arching effects have been quantified based on centrifuge modeling studies for the different mining conditions. Observations have indicated that the degree of arching is a function of stope geometry, wall roughness, fill cohesion, and wall closure. Arching effects increased with decreasing stope width, increasing backfill cohesion and frictional resistance, increasing wall roughness and with wall closure.

May 1, 2002

By Harlan A. Walker

This paper on the mines of El Potosi Mining Co. is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the various mining districts of North America. Grateful acknowledgment is made of the helpful suggestions and criticisms offered by the management, together with the assistance of the mining staff in preparing maps and drawings and of C. L. Thornburg, mine geologist, in preparing the section on geology.

Jan 1, 1934

By R. Bellotti

The theory of cavity expansion in an infinite frictional soil mass whose strength is represented by a curved Mohr-Coulomb failure envelope has been used to predict with some confidence the cone resistance of a clean dry sand. Experimental data were obtained from cone penetration and pressuremeter tests on two sands, conducted in a large calibration chamber (CC) under carefully controlled placement and boundary conditions. A plane strain bearing capacity theory was developed, and to convert the results to axi-symmetric conditions, an empirical "shape factor" was used. In the paper, the theoretical background, experimental data, calculation procedure, and the results of the analysis are presented. In general, a reasonable validation of the cavity expansion approach to the bearing capacity of deep foundations has been obtained.

Jan 1, 1987

By K. B. Bengtson

This task report provides the process technology, preliminary design, capital and operating costs for a 25 TPD pilot plant to produce cell-grade alumina using a clay/hydrochloric acid extraction - HCI gas induced crystallization process. The report consists of six volumes: I - Process Technology and Costs; II and III - Equipment Lists, Specifications and Quotations; IV and V - General Specifications; VI - Drawings. The process was selected by the Bureau of Mines as the more promising method to produce cell-grade alumina from clay based on the results of the two previous task reports under this contract: Task I - Comparison of Six Processes (alunite, anorthosite-lime sinter, clay/sulfurous acid, clay/nitric acid, clay/hydrochloric acid evaporative and gas-induced crystallization) and Task 2 - Comparison of Two Processes (clay/nitric acid and clay/hydrochloric acid - gas induced (crystallization). The pilot plant process utilizes a unique dual crystallization process to produce aluminum-chloride-hexahydrate crystals having sufficient purity when decomposed to meet stringent alumina product specifications. The size of the 25 TPD pilot plant has been selected to permit scale-up to commercial size plants of equipment, technical and economic parameters. The capital cost estimate for the pilot plant, exclusive of fee and escalation, for a southeastern U.S. location is $52,311,000 expressed in 1979 dollars. The total time required to construct the pilot plant including engineering and procurement is 32 months. The operating cost to produce the estimated 9,000 tons of alumina required for testing in Hall cells is $40,91[0],190 expressed in 1979 dollars.

Jan 1, 1979