Search Documents

By H. C. Theuerer

EVEN the highest purity silicon available for semiconductor use contains significant amounts of donors and acceptors, usually aluminum, phosphorus, and boron. Aluminum and phosphorus can be removed from silicon by adaptations of the zone refining techniques' widely used with germanium. Removal of boron, however, has been a difficult problem. The approximate distribution coefficient for boron in silicon is 0.8, so that while zone refining is possible, it is not very effective in any reasonable number of passes. It has been found, however, that boron can be effectively removed from silicon by treatment of a liquid zone with hydrogen and water vapor. Starting with 40 ohm-cm, n-type silicon, use of zone refining coupled with hydrogen

Jan 1, 1957

Jan 2, 1951

By Jesse Betterton

IN the Parkes process of lead refining, after desilverization has been completed by means of zinc additions, there will remain in the lead from 0.5 to 0.6 per cent zinc. At this stage in the refining practically all impurities are reduced to refined lead specifications except zinc and antimony. All excess of copper and nearly all the arsenic goes out with the silver. Silver remaining should not exceed 0.1 oz. per ton. It thus remains only to remove zinc and antimony to produce refined lead. The older practice was to complete refining by means of oxidation processes in reverberatory furnaces. Essentially this consisted of heating the lead to 1200° to 1300° F. and allowing it to come in contact with a considerable excess of air passing through the furnace, or accom-plish the same result by blowing the lead with steam by means of pipes introduced for that purpose, at the same time allowing air to enter the furnace. Usually some procedure involving alternate oxidation and reduction with fine coal or coke was employed in order to reduce the weight of dross or skim finally removed from the furnace. This practice had many elements of weakness in that the main flow of lead, after the preceding expensive operations had been performed, and the whole refining process nearly completed, was subjected to an operation at a comparatively high temperature, which involved much lead loss if the furnaces were not on bags, and the production of 3 to 5 per cent of the weight of the lead as dross or skim, which had to be resmelted and the lead either refined or produced as antimonial lead. In addition, the operating expense of the process was a considerable item. The, process of dezincing with chlorine was developed as a substitute for the foregoing described oxidation process, and finally resulted in such advantages as nearly equal operating costs, a practical elimination of the lead loss, and the direct production of a very valuable byproduct, zinc chloride, that may be sold as such or retreated for its zinc and chlorine contents, both of which can be reused in the refining processes.

Jan 1, 1933

By J. C. Danko, R. D. Stout, A. H. Holtzman

The deformation characteristics of pearlite have been studied by light and electron microscopy.1,2 In the electron-microscopic work, deformation was found to take place by 1) ferrite slip which is parallel to the lamellae, 2) slip transverse to the lamellae with both cementite and ferrite deforming, and 3) ferrite-cementite interfacial slip. The transverse slip gives a step-like appearance to the lamellae in light microscopic work. It was thought that spheroidization of deformed pearlite would commence at the regions of maximum cementite deformation, the "stepped" areas. Although there is no possibility for seeing slip in the microstructure if the specimen is polished after deformation, the step-like appearance of the lamellae clearly indicates the transverse deformation. Thus, the areas of cementite deformation are apparent after polishing and the effect of deformed areas on spheroidization may be studied by the usual metallographic techniques. This note reports the result of a metallographic investigation which substantiates that spheroidization begins in the "stepped" areas. An AISI 1080 steel was normalized, re-austeni-tized at 1040°C, and isothermally transformed at 700 ± 4°C for 4 hr. Cubes, 5 mm to a side, were compressed between parallel plates to strains of 20, 40, and 50 pct. After deformation, specimens were heated to 600, 650, and 700°C; withdrawn at increasing time intervals and examined metallo-graphically for the percentage and distribution of spheroidite. The percentage of spheroidite was determined by lineal analysis. A micro structural region considered as spheroidized was one in which a lamellar skeleton was not distinguishable. Table I gives the times necessary for 95 pct spheroidization for each condition of strain and annealing temperature. Fig. 1 shows the microstructure of coarse pearlite compressed 20 pct, then polished and etched. Here the lamellae form a step by bending at two

Jan 1, 1959

By W. Evans, C. E. Ells

The agglomeration of hydrogen in pure aluminum and A1-Mg alloys has been studied through use of hydrogen introduced into the metal by cyclotron proton irradiation. Both the growth and dispersal of the agglomerates have been followed by metal-lographic techniques. During the cyclotron irradiation, agglomeration occurs at temperatures i 100°C for hydrogen concentrations as low as 1 ppm. On heating at elevated temperatures, 300°C to 600°C, intragranular agglomerates first coarsen and then disperse. The agglomerates formed at grain boundaries are much larger than the intragranular agglomerates; with hydrogen concentra- tions > 10 PPm, heating for 1 hr at 500°C results in extensive grain-boundary cracking. The hydrogen agglomerates have been shown to inhibit grain growth, but no inhibition of recrystallization has been observed. The ability of hydrogen to enter aluminum at a free surface, combined with its high-diffusion rate at elevated temperatures, accounts both for growth and dispersal of the agglomerates. Irradiations at elevated temperatures give results consistent with the explanation proposed for agglomerate behavior on post-irradiation heating. 1 HE formation of hydrogen-filled bubbles, or blisters. in aluminum and its alloys has been studied for over' thirty years. The work up to 1952 has been reviewed by Kostron' and since then Ransley and

Jan 1, 1963

By W. N. Best

(San Francisco Meeting, September, 1915) INTRODUCTION CRUDE oil attracted attention because of its excellence as a fuel for open-hearth furnaces; for making crucible steel and brass; for melting copper, lead, tin, zinc, nickel, silver, malleable iron, gray iron; and for the production of steam in all sizes and types of boilers. For heating furnaces, mold-drying ovens, core ovens, ore roasters, calciners, hot-air furnaces, sand drying, asphalt road work, etc., its superiority over other fuels is due to the fact that the heat is at all times under perfect control, so that a constant temperature may be attained and maintained at the will of the operator. This means a maximum amount and uniform quality of work. Crude oil is of two kinds, paraffine base and asphaltum base, and varies from 11 to 46 gravity Baumé. The light-gravity oil does not require heating before use; but oil of less than 20 gravity Baumé should be heated to just below its vaporizing point, in order to reduce its viscosity and to obtain the highest efficiency of combustion. Heavy California oil vaporizes at 230°'F., Mexican crude oil at from 175° to 210° F., and Beaumont, Texas, oil at 142° F. Fuel oil vaporizes at 130° F.

Jan 8, 1915

By George W. Doffing

Numerous contradictory statements have been made in the past regarding the importance of the seasonal influence of demand for motor fuel on prices of oil securities. It has often been said that the time to buy oil securities is in the spring, or just prior to the heavy consuming season for gasoline. The fallacy of this argument is brought out in the following paragraphs. Seasonality of Oil-security Prices The indexes used in this paper as indicators of prices of oil securities and general industrials are those compiled by Standard Statistics Co. The oil producing and refining stock index includes 14 representative petroleum companies, while the all-industrials index is made up of 347 issues. All figures are stated as relatives, with 1926 = 100. The primary basis of the index, and one that gives a good weighting of the relative importance of the company within the industry, is the total market value of the stock issue outstanding; i.e., the market price times the number of shares outstanding. Adjustments are made for the addition or elimination of issues from the group index, for stock dividends, split-ups, stock rights, et cetera. At the present time the oil producing and refining index includes the following companies: Atlantic Refining Co., Consolidated Oil Corporation, Continental Oil Co., Gulf Oil Corporation, Humble Oil & Refining Co., Ohio Oil Co., Royal Dutch Co., Shell Union Oil Corporation, Socony-Vacuum Oil Co., Standard Oil Company of California, Standard Oil Co. (Indiana), Standard Oil Co. (New Jersey), Texas Corporation, Union Oil Company of California. In calculating the seasonal for oil-security prices several periods have been selected as indicat,ive of major changes in the industry, as follows: 1. 1918 through 1936. This gives an over-all picture of the industry during the motor-vehicle, motor-fuel era. 2. 1927 through 1936. This period includes the control stages, both voluntary and coercive. 3. 1927 to September, 1933. This is the pre-code period of control.

Jan 1, 1937

By G. B. Pryde, R. M. Magraw

In laying out a new mine, provision should be made for the ultimate recovery of as much coal in any given bed as is consistent with safety and economic mining. Though each mining district, if not each individual mine, has problems that make the adoption of any hard and fast rule impossible, certain basic principles are adapted to practically all conditions. One of the most vital is the provision for barrier pillars of ample dimensions to protect all haulage and permanent airways during the life of the property. Where conditions permit, room or butt entries should be driven on the strike or slightly to the rise, and rooms turned at right angles to these entries. The width of rooms and room pillars is governed by conditions prevailing in the mines under consideration. A safe rule is: In advancing, extract not more than 25 to 35 per cent. of the entire seam; in exceptionally thick seams, considerably less than 25 per cent. should be taken. Rooms usually vary in length from 250 to 350 ft. (76 to 106 m.) with a barrier pillar of not less than 80 ft. between the last crosscut. in rooms and the back entry of the level above. All entries, rooms, and entry-and-room crosscuts should be driven .on sights and room crosscuts should be driven at, right angles to the direction of the rooms. In mines under excessively heavy cover or where roof conditions are bad, rooms should be driven narrow and a barrier pillar left at every fifth to tenth room. This barrier should be of such dimensions that one or more rooms, with pillars of usual dimensions, may be turned through it when the barrier is no longer required. Two of the advantages of such a barrier are the protection of the panel against peaking of roof load during pillar extraction and the easy closing of the entry in case of fire. Where economic conditions permit, it is preferable to follow the retreating panel system of mining. In the case of coal that outcrops, and even in cases where no outcrop is exposed, it is preferable to commence pillar extracting on the high side of the mine. Where the retreating

Jan 1, 1922

By G. W. Garside

In order to render my descriptions more intelligible, I have compiled a general map of this section of Alaska, showing accurately the relative positions of the most important districts where valuable deposits of minerals have been discovered (page 819). Upon inspection of this map, it will be observed that the chief metalliferous belt in this mineral field is in close proximity to the mainland shore, the trend of which it follows for more than a hundred miles in a northwest and southeast course, while the mineral croppings on the adjoining islands are much shorter in extent, and more irregular with respect to their strike and continuity. This principal metalliferous zone, which I will call the main-land system of lodes, contains gold, silver and lead, besides traces of copper, zinc and iron, gold being found extensively in a free state and also associated with sulphur, and with many of the sulphides of iron, lead and other substances. On the line of this belt, as shown on the map, there are a number of distinct mineral districts. Beginning at the southerly extremity, they are named as follows: Sumdum, Snettishham, Grindstone Creek, Sheep Creek, Gold Creek, Lemon Creek, Montana Creek and Berners Bay districts, each deriving its name from the hay or creek on which it is situated. Harris mining district, as legally organized under the local customs, rules and regulations adopted by the miners of Juneau, embraces, within its exterior boundaries, Grindstone, Sheep, Gold and Lemon Creeks, and all of Douglas Island. The limits of this immense metalliferous horizon are becoming definitely known through the exposures made by prospectors. The belt, as now recognized, varies in width from one to several miles, the lateral measurement being greatest at Juneau in Harris district, where the famous Treadwell mine, with its slate foot-wall, marks the westerly boundary of the zone, while the eastern side of Silver Bow Basin, with a granite hanging-wall, defines its easterly border.

Jan 1, 1893

By A. Taylor

IN a previous communication,l the quaternary system Ni-Cr-Ti-A1 was described in detail and it was shown how certain alloys used for high-temperature applications could be construed as consisting of Ni,Cr suitably modified by the addition of aluminum and titanium in relatively small amounts. With the correct aging treatment, the ordered face-centered-cubic Berthollide phase, y'-Ni,Al, could be precipitated from the face-centered-cubic primary y-solid solution. By increasing the proportion of titanium with respect to aluminum, it was also possible to precipitate the very brittle hexagonal-close-packed Daltonide phase, ?-Ni,Ti. From the nature of the system it seems reasonable to expect the y and y'-phases to take appreciable amounts of cobalt and iron into solid solution. In the case of the present investigation it was decided to confine the work to iron additions only. This element may be introduced in two quite distinct ways: 1) as a simple replacement for nickel; and 2) as a replacement for chromium, titanium, and aluminum. The second method of iron addition forms the basis of the present investigation, which is, in effect, a study of the pseudo-quaternary system Ni,Cr-NiPe-Ni,Ti-NLAl. For purposes of reference, Figs. 1, 2, and 3 have been included and illustrate the quaternary system Ni-Cr-Ti-A1 described in the previous paper along with sections through N&Cr-Ni,Ti-Ni,Al at 750" and 1000 "C respectively. As will be shown below, the pseudo-quaternary system with components Ni,Cr, NiPe, Ni,Ti, Nihl is remarkably similar in many ways to the face defined by Ni,Cr-Ni,Ti-Ni,Al because of iron re-

Jan 1, 1958

By E. G. Leonardon

The object of this paper is to describe briefly the practical results obtained in several problems of civil engineering by resistivity measurements of the underground. It is intended for the mining engineer, as well as for the construction engineer; the stratigraphical problems discussed are general and frequently are encountered in mining exploration. Resistivity measurements have been used in mining and oil exploration for a number of years.' Their introduction in the field of civil engineering, on the contrary, is rather recent. It was applied for the first time in the spring of 1928 near Littleton, N. H., in the survey of two dam sites for the New England Power Assn.2 Since then, the geophysical firm with which the author is connected has had an opportunity to develop this field of activity, and more than 20 investigations at dam and tunnel sites have been carried out in the United States and Canada. A part of this work has been verified by underground or drilling exploration. This paper deals with but a few of the results, which we are permitted to make public now. The theoretical and technical sides of the processes employed will not be discussed; they have already been described in various technical publications. A few general points will be mentioned, to make clear the practical examples given. Resistivities OF the Rocks The surveys are based on the measurement of the specific resistance of the rocks. This resistivity is the electrical resistance of a cylinder of

Jan 1, 1932

By C. E. Corson

The experiments of which the results and significance are set forth in this paper do not by any means cover the whole subject of the heat-treatment of the material referred to, yet they constitute a contribution to that general subject, rather than to the special department of' annealing. The material here considered is acid open-hearth steel, containing from 0.50 to 0.80 per cent. of carbon, with a nearly uniform percentage of other elements. This class of steel is rapidly increasing in commercial importance. It is even rumored that the rail-specifications of some railroads will hereafter require open-hearth steel. Yet this particular grade seems to

Jan 1, 1907

By D. H. Forbes, H. M. Manasevit, F. L. Morritz

Single-crystal thin films of molybdenum have been grown. by the pyrolytic decomposition of molybdenum hexafluoride in a hydrogen ambient on various insulating substrates at temperatures front 650° to 900° C. Single-crystal discs of various orientations of magnesium aluminate spinel, a aluminum oxide, magnesium oxide, and the natural facets of beryllium oxide were all observed to exert epitaxial control on the depositing film. Determinations of the crystallographic relationships existing between film and substrates have been made, using X-ray diffraction three-circle goniometry and Laue back-reflection techniques. Using these data, crystallographic overlays have been constructed which suggest a possible interfacial geometry on the basis of a match between metal deposit atoms and metal ion sites in the substrate. A continuing program has been in effect in the Auto-netics Laboratories over the past several years aimed at the development of electronic materials in new and useful forms using chemical vapor deposition techniques. During the course of these investigations, the epitaxy of silicon1"5 and tungstenep7 on single-crystal metal oxide insulators was studied extensively. The deposition of molybdenum is a logical extension of the tungsten work since the crystal structure is identical and the lattice dimensions differ by less than 1 pct. The pyrolytic decomposition of molybdenum hexafluoride in hydrogen was used to grow molybdenum films on the oxide substrates AlzOs, MgA1~04, MgO, and Be0 at from 650" to 900°C, depending on the substrate material. Under the experimental conditions to be described, monocrystalline films of controlled orientation were obtained. The materials investigated and their crystal structure are listed in Table I. EXPERIMENTAL The molybdenum depositions were effected by the hydrogen reduction of molybdenum hexafluoride (MoFe) in a flowing system of hydrogen at atmospheric pressure. The schematic of the apparatus is shown in Fig. 1. The hydrogen, purified by passage through a heated palladium thimble, was mixed with the vapor of the liquid MoFe maintained in a steel bottle at room temperature (25°C). The mixture was passed over the substrate, which was heated by rf induction of a sup-

Jan 1, 1969

By Frank W. Cramer

THE operator's panel is the control center f or the operation of the electric-arc furnace. It contains the switches and meters that control and indicate the power supply and in a way gives a picture of what is going on during the meltdown and refining periods. Regardless of manufacture, these panels are very similar with respect to equipment and position of apparatus. A typical panel is shown in Fig I. The three lights at the top of the panel are connected from the electrodes to ground and give a visual measure of the voltage across each arc. The ammeters underneath the lights show the current passing through each electrode. Directly underneath are the voltmeter, the watt-hour meter and the wattmeter and under these the three current-adjusting rheostats. In the center of the panel is the master electrode-control switch, which controls the movement of all three electrodes, with the individual electrode-control switches directly underneath. Next from left to right is the six-position voltmeter switch, which can be positioned to show on the voltmeter above the voltage between phases and to ground, the tap-changer switch with its indicating lights, and the main circuit-breaker control switch.

Jan 1, 1947

By Howard L. Hartman

There is reason to believe that ventilation systems so far devised for use with continuous mining machines fall far short of success. This is vividly demonstrated to anyone who has observed in a continuous miner section the localized ignitions of pockets of gas and the generation of dense clouds of dust by the cutting head of the machine. The alarming frequency with which major ignitions and disasters continue to occur in modern mechanical mining and the rise in incidence of pneumoconiosis serve as reminders that our ventilation systems are far from achieving the ultimate in providing protection from either short-term explosions or long- term dust diseases, both of which take lives. Human safety is the main concern in ventilation. But in this day of high-priced labor, let us not forget human comfort, either, for this is a major factor in motivation toward high productivity. The failure or inadequacy of most mine ventilation systems in providing the kind of working conditions at the face that are conducive to productive as well as safe operation is an indictment of our environ- mental control program in mining generally.

Jan 3, 1962

By A. H. Bell

The general principles of the gas-lift will not be described in this paper. Only specific details that have not been fully discussed in previous papers, or results that do not fully coincide with conditions previously described, will be dealt with. The principal points to be emphasized and for which supporting data are furnished are as follows: 1. Gas-lift installations usually have comparatively high efficiencies as compared with standard pumping equipment, when reduced to a basis of barrels produced per horsepower installed. 2. Advantages of high-pressure plants from the standpoint of operating efficiency and for the application of the gas-lift early in the life of flowing wells. 3. Evidence of increased ultimate yield through conservation of gas by the gas-lift. 4. Possibility of development of new equipment to increase efficiency of the gas-lift. 5. Indications of the advantages of repressuring as a means of stabilizing gas-lift wells and as a means of increasing ultimate yields. TyPes of Installation The gas-lift installations of the more important companies in California have been of the central-plant type wherever field conditions would permit. This has resulted in greater flexibility and lower installation costs per well than could be obtained with individual well units. In general discussions of the gas-lift method of production, the installation costs are frequently referred to as being too high for economical operation. If the field conditions are carefully analyzed and the plant designed with the idea of obtaining high operating efficiencies, the installation cost per well can be lowered sufficiently to compare favorably with individual well-pumping units, when the operating advantages are considered. Much greater production per horsepower can be obtained with the gas-lift than is possible with pumping equipment. Table 1 shows the unit sizes and costs of gas-lift installations of three companies in the Los Angeles basin. The cost of walking beams, rods,

Jan 1, 1928

By William C. Buell

As used in connection with open-hearth or other high-temperature operations, "insulation" refers to a multitude of substances, natural or manufactured, that have the one principal property of preventing the flow of heat by conduction to a greater degree than refractories can prevent it, the principal properties of the latter being resistance to temperature and/or chemical action. The term "control" as commonly applied to the mechanization of management functions is inappropriate without qualification, for without some degree of control of every operation we could produce no steel worthy of the name. Although grouped together in this paper, insulation and control in open-hearth furnaces have little, if any, interrelationship, therefore the paper is made up of two distinct parts. INSULATION OF OPEN-HEARTH FURNACES More than ten years ago the writer proposed the insulation of an acid open-hearth furnace system below the charging floor, and it was accomplished, with gratifying results. Possibly that was the first time the insulation of regenerators and slag pockets of any open-hearth furnace was undertaken, but shortly thereafter such insulation became general, and when the six groups of 150-ton furnaces1 were built in 1929-1930, they were completely insulated below the charging floor. While the practice was accepted at least five years ago, it was not well understood, however, as indicated by the following incident which occurred in connection with an installation made in 1929. After the

Jan 1, 1935

By H. A. Schwartz

THE spheroidal form of the temper carbon nodules in malleable cast iron and of the graphite mottles of "mottled" cast iron suggests that in both all the graphite in a given mottle or nodule grew from a single center of crystallization or nucleus. ? There is, however, a distinct metallo-graphic difference between the mottle and the nodule; the area of mother metal impoverished in combined carbon by the crystallization of graphite in a mottle is practically coextensive with the ramifications of the graphite, while the impoverished zone of metal corresponding to a given nodule is always larger, and usually much larger, than the approximately spherical mass of graphite crystals forming the nodules. Furthermore, the mottle probably is formed during freezing and the nodule almost always at a considerably lower temperature. Assuming that the nodules or mottles can be used as a measure of the existing nuclei (capable of germination) we propose to record certain observations as to the graphitizing reaction in the light of the number and habits of growth of these nuclei. The present authors, in cooperation with others1-7, have reported upon various cognate aspects of the problem. The fact that temper carbon is a mass of flakes and not a solid granule has become well recog-nized since the introduction of an improved polishing technique8,9,10 for cast iron. The problem of deriving from the circular planar intercepts

Jan 1, 1936

By Anthony Folger, Charles E. Straub

Kansas produced 38,150,878 bbl. of oil in 1928 and 40,658,170 bbl. in 1929, thereby retaining its rank as fourth among the oil-producing states of this country. Production for 1928 was less than that for 1927 (Fig. 1) because of a decrease in the number of completions, but the average initial production per well (Table 1) shows an increase due to the completion of wells of comparatively large capacity in the new Valley Center pool of Sedgwick County. This increase in average initial production per well was further augmented during 1929 by completion of additional wells of comparatively large capacity in the Valley Center pool and the new Greenwich pool of Sedgwick County. Production for 1929 exceeded that for 1928 and threatened to exceed all records except that of 1918, however, production was prorated in

Jan 1, 1930

By S. Zador, C. B. Alcock, K. Sudo

Measurements have been made of the standard free enevgies of formation of the sulfates of cobalt, Cupric copper, nickel, and ferric iron in the temperature range of 750° to 950°C. Dynamic gas-solid techniques have been employed in which oxide-sulfate and basic sulfate mixtures were placed in a stream of gas of controlled SO3 potentials. Thermal analysis and thermogvavimetry were used as detection methods, and it was found THE formation of sulfates during the roasting of sulfide ores is now considered to arise in many cases from the interaction of sulfur trioxide in the gas and the metal oxide which is formed on the sulfide as a first step.' As a preliminary to the investigation of the kinetics of sulfate formation during roasting, measurements have been made of equilibria from which the free energies of formation of cobalt, copper, nickel, and iron sulfates can be that the range of temperatures which could be investigated and the choice of method was largely controlled by the kinetics of these gas-solid reactions. The results are compared with previous results obtained from static measurements with which they agree quite well, and calculations have been made employing themal data to interrelate the present results with those for other sulfates. calculated. The method used has been to expose the solid sulfate (or basic sulfate) to a controlled flowing gas mixture of SO,, 02, and SOs and to observe the temperature of decomposition. The onset of decomposition was detected by thermal analysis or thermogravimetry. EXPERIMENTAL METHODS The thermal-analysis method was similar to that employed by Dewing and Richardson.' The sulfate was dehydrated at 250°C in air, and placed in a small alumina crucible which was held by a quartz ring in the hot zone of a horizontal furnace. The reaction tube of this furnace was made of mullite.

Jan 1, 1965