Search Documents

By L. P. James

The Bulagidun copper-gold system occurs in Tertiary andesitic volcanic rocks. It is located (figure 1, from Curless, 1991) ca. two days walk from the coast in an isolated area on the northerly slope of the main range of mountains, in steep terrain dissected by erosion. Detailed and district-scale exploration from 1988 to 1991 by BHP Minerals defined a small, sub-economic resource of gold and copper. One preliminary estimate of the resource in bedrock suggests 14.4 million tons at 0.68 grams / Tonne Au and 0.61% Cu, in multiple small bodies.

Jan 1, 1993

By D. C. Hatch

At the MacIntyre Development of the Titanium Division of National Lead Company a magnetite-ilmenite ore together with gabbro-anorthosite waste is mined from an open pit by shovels and trucks. The ore from the pits is trucked to ore stockpiles for blending ahead of the crusher and to free the mine from crusher delivery schedules. The ore stockpiles are blended to yield a 16.5 to 17.0 % TiO, crusher feed. This requires mining on an assay cut-off rather than a visual grade cut-off. Highly mineralized ore runs from 20 plus % TiO2 and 30 plus % Fe to 15 % TiO2 and 40 plus % Fe as the ratio of ilmenite to magnetite changes. There are three major ore types in the present pit with magnetite ratios varying from about one to one up to three times as much magnetite as ilmenite. Ilmenite and magnetite together liberate from gangue down to about 10 mesh and this is the basis of the magnetic cobbing. Below 10 mesh the ilmenite and magnetite start to separate and ore cobbing pulleys will not hold the ilmenite.

Jan 1, 1968

By Jack Parker

Cycles of mine convergence coincide with annual cycles of temperature and humidity in the mine. Laboratory measurements confirm that the presence of moisture reduces rock strength and induces internal rock stress. Findings are used in the design of mine openings.

Jan 1, 1969

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

1.1 INTRODUCTION When underground mining involves total extraction, it induces overburden strata movements. If not properly planned it causes surface subsidence and affects surface environmental conditions. Total extraction usually refers to longwall mining and room and pillar mining with pillar extraction. Surface subsidence has long been a subject of intensive research for scientists all over the world and considerable achievements have been obtained. However due to its difficulties and complicated nature, research into overburden movement has been thus far incomplete as compared to that into surface subsidence. Since surface subsidence is a manifestation of the results of overburden movement, the processes and mechanisms of overburden movement must be fully understood in order to establish the mathematical prediction models of surface subsidence. In this chapter the processes of overburden movement and its zones of movement in the overburden will be discussed. 1.2 PROCESSES OF OVERBURDEN MOVEMENT When total extraction is used, it produces a large void in the coal seam and disturbs the equilibrium conditions of the surrounding rock strata. The roof strata bend downward while the floor heaves. When the excavated area (or gob) expands to a sufficient size, the roof strata will cave. As a result, the overlying strata continue to bend and break until the piles of the fallen rock fragments are sufficiently high to support the overhanging strata. At this tie the overhanging strata no longer cave, but bend and rest on the underlying strata. Strata bending and subsidence develop upward until reaching the surface and forming a subsidence basin. The whole overburden strata and the surface subsidence basin will further go through a period of compaction and gradually become stabilized. Current knowledge regarding the process of overburden movement has been derived from several sources. One is the direct observation of the mined sections and their surfaces, another from field monitoring of strata movements in the overburden, and others from computer modeling and scale modeling in the laboratory. For example, Figs. 1.1 and 1.2 show the results of a borehole monitoring experiment (Borehole B-2) using the full profile borehole inclinometer and full profile borehole extensometer for lateral displacements and vertical subsidence, respectively (Conroy and Gyarmaty, 1983). The panel, 400 ft wide by 5000 ft long and 630 ft deep, was extracted from the Pittsburgh No. 8 seam which had an average thickness of 54 in. The face advanced from east to west. Curve A in Fig. 1.1 shows the inclination of the borehole when it was 45 ft ahead of the face at Position A (i.e., on the solid coal side). The total deviation of the borehole was 1/7000. The first shear movement occurred at 130 ft above the coal seam and appeared to have occurred along the bedding plane with large contrast of rock strata on both sides, i.e., sandstone vs. shale. When the face had passed the borehole 79 ft at Position B, the borehole deformed to assume a bow shape with a maximum deviation of 2.8 in. from the center line. Numerous shearing planes occurred and extended further upward. When the face had passed the borehole by 75 ft at position C, strata subsidence was measured. Fig. 1.2 shows that a strata separation as large as 4 ft occurred at 40 to 100 ft above the coal seam. Above this level, the strata subsided more uniformly with bedding separations within 1 to 2 in. Another example is the longwall mining with complete caving in the Soviet Union's Karaganda Coalfield (Kolebaeva, 1968). The coal seam was 6 ft thick and 154 ft deep. The immediate roof was the fine-grained sandstone interbedded with coarse-grained sandstone. Above this, there was sandy shale and shale. In order to monitor the process of overburden movement, 15 stations were established in a borehole (Fig. 1.3). The elevations of those stations were measured when the face was at various distances from the borehole. Fig. 1.3 shows the movement history of each station. For convenience of comparison, the movement history of each station was plotted on a common reference point as shown in Fig. 1.4. Clearly, the movements of strata from Station # 1 to #6 were nearly simultaneous, i.e., they behaved as a single unit. The strata from Station #7 to # 15 had differential separations, the maximum of which was 40 in. As the face passed by and moved away, strata separations in general reduced gradually. But strata separation between Stations #12 and #13 remained the same until the end of the monitoring period. The total bed separation between Station #7 and # 15 reached 11 in., approximately 18% of seam thickness, when the face was 132 ft beyond. Based on the above observations, the author developed a conceptual model of overburden movement due to underground longwall mining (Fig. 1.5). The above-mentioned two case studies illustrated that subsidence in the overburden strata propagates upward and subsidence velocity decreases from the bottom to the top. When the subsidence velocity at the surface reaches the maximum value, the subsidence velocity at the bottom portion of the overburden strata has decreased considerably and the strata have begun to compact. Bed separation occurs within a certain distance above the coal seam and reduces from the bottom to the top. When the face has moved away, bed separation reduces gradually, so that eventually some beds completely close and others partially close. Bed separation reaches the highest level when the subsidence velocity at the surface is at its maximum value. For instance in Fig. 1.4 surface subsidence velocity was maximum when the face was 38 to 44 ft past the point. At this time the total bed separation was maximum. Overall the strata directly above the opening are subjected to tension in the vertical direction. But above a certain level, all strata move nearly simultaneously. There is also significant shear movement along some bedding planes. 1.3 ZONES OF MOVEMENT INTHEOVERBURDEN After the extraction of a longwall panel or room and pillar section of sufficient width the strata in the overburden are subjected to various degrees of movement from the bottom to the top. According to the movement characteristics, the damaged overburden can be divided into four zones (Fig. 1.6). Caved Zone. After the extraction of coal, the immediate roof caves irregularly and fills up the void. The strata in this zone not only lose their continuity completely, they also lose their stratified

Jan 1, 1992

By Arthur A. Brant

Your chairman has asked me to deal with questions of education relative to our present and projected trends in the field of mineral expiration. First comes our definition of education--and education is not the merely formal acquiring of academic knowledge, but the understanding, using and projection of knowledge into our channels of life and thought activity. This past year makes us realize the extent to which price and economic cut-off may stimulate or curtail exploration,, But exploration does not consist solely in the discovery of sources of material. There is just as inspiring and imaginative a territory in the develop¬ment of uses and application--and no one in our base metal industry but would hope that our educational processes would fertilize those springs of inspiration that lie dormant in us all, toward the- imaginative conception of new uses--lead roofing cloths or felts, non-tarnishable copper utensils, further zinc solid state application. Thus an educational pattern should seek to develop imagination and thinking beyond--the possibility of that small but oh so difficult step just ahead of the existing,

Jan 1, 1959

By Theodore Balberyszski

The gradual depletion of high-grade sulphide mineral deposits has turned the attention of the mineral industry to the recovery of metals from the oxides and silicates. Anionic (fatty acid) and cationic collectors have in some cases made flotation of non-sulphides possible, although in general, flotation of oxide ores is not as yet an economic process. Consequently, many attempts have been made to sulphidize the surface of the relevant oxide mineral and thus make it amenable to flotation. (1) (2) (3) In recent years, Bautista and Sollenberger(4) have investigated the conversion of a number of oxides to sulphides by reacting them with molten sulpur. This paper presents the results of investigations carried out at the School of Mineral and Metallurgical Engineering at the University of Minnesota to study the flotation characteristics of some sulphidized minerals. It is divided into two parts; Part I describes the sulphidization of a number of oxides and a silicate, and Part II presents the flotation behavior of the products of sulphidization.

Jan 1, 1968

By Norman L. Weiss

The full importance of tailings disposal is yet to be realized by the mining industry, but our awareness of its present and future implications is growing faster, perhaps, than any single phase of ore processing. Few engineers can look very far into the future because of the complexity of the problems that may confront us if we project from the general indifference of past years through what we are already being expected to correct in existing operations, to confrontations with new statutes and an awakened public in any new plants hence- forth. The mistakes of the past have not been limited to the United States nor even to other countries of the Western Hemisphere. Indeed, all continents and subcontinents have suffered from myopia in releasing the tailings without retaining responsibility. However, the US as one of the world's great leaders in technology has a particularly unimpressive record. It may be safely generalized that the degree of control applied to the tailings of a milling operation has depended upon several factors more important than national boundaries. Thus in arid and semiarid climates no incentive was needed other than the scarcity of water to create a permanent and stable lodgment for mill tailings. On the other hand. where water has been plentiful. the temptation to let the tailings run into a river or lake or ocean (at least at certain times of the year) was often irresistible. So we find that modem tailings disposal in the southwest deserts of this country, with one or two notable exceptions where very serious breaks seem to occur at regular intervals, is satisfactory according to the standards of the 195QF and 1960s. while in various operations in Idaho, Michigan, western Colorado. Newfoundland, and elsewhere the record has been less praiseworthy. In the same way, cyanide plants which did not concern themselves about leakage, seepage, spillage, or wastage of tailings pulps with solutions containing toxic levels of free or combined cyanide soon heard a demand for better control. In consequence the industry has seen a growing use of cyanide regeneration of tailings or wash solutions, elimination of leakage, and careful structuring of tailing dams. The chemical and thermal qualities of tailing waters have occasionally been a spur to good tailings management. Some tailings disposal problems for example, the southeastern Florida phosphate clays and the Bayer red muds-have been given the intensive study they merited, but not always with much success.

Jan 1, 1985

By Everett H. Dobbs

The Tripoli deposits in the southwest corner of Missouri In Newton County and the northeast corner of Oklahoma in Ottawa County, located in the vicinity of Seneca, Missouri, contains an unusual and peculiar form of silica which has not been found any other place in the world. Its outstanding characteristic is the physical structure of the individual particle, The particle structure of the Missouri-Oklahoma type Tripoli accounts for its market. It is a soft, friable, porous, double-refracting silica of the chalcedony variety, The particle is porous, has a fibrous structure, no sharp edges or comers, ad an average size of less than .01 millimeter, It varies from 90 to 98 per cent Si02 with less than 1 per cent free silica in the form of quartz, 24; has ignition loss of 1 per cent and fractional percentages of iron, alumina, lime, etc.

Jan 1, 1960

By D. C. Ridenour

The pressure system of ventilation with large diameter bore holes has been very effective in the ventilation of two gaseous mines, the Olga No. 1 and No. 2 Mines in McDowell County, West Virginia. The No. 4 Pocahontas Coal Seam on the Olga property lies 580 feet below the valleys. The seam is very gaseous as well as dry and dusty, which makes good ventilation all the more essential. Irregular and often extensive areas of the coal seam have been replaced with impervious shales and sandstones in "Fault" or "Want" areas. The replacement materials have sealed the methane in the coal seam and thus increased the quantity of gas that must be handled as mining is done. Often the No. 5 Pocahontas Seam comes down to meet the No. 4 Seam at the Faults and considerable methane is sometimes released from the upper seam. The factors mentioned, together with the irregular and unpredictable lateral shape' of the faults, result in long narrow stringers of coal that are very gaseous and difficult to mine. So far as the Olga Coal Company is concerned, the most effective ventilation under the conditions outlined has been the use of large diameter bore holes with a pressure ventilation system. The ventilation of a mine can be accomplished in two fundamental ways. The mine atmosphere maybe reduced below atmospheric pressure by an exhaust fan; or it may be raised above atmospheric pressure by a pressure fan. In either case, the coursing of the air is so planned as to have the haulage and traveling ways on intake air. While the majority of the coal mines in the United States, no doubt, use the exhaust system of ventilation, there are several advantages of the pressure system which are extremely beneficial.

Jan 1, 1960

By William R. Barton

The domestic portland cement industry consumes more than 12 million tons annually of raw materials chemically similar to fly ash. How these materials are used and how fly ash can serve in their place are discussed. Factors influencing whether or not a particular plant will use fly ash in place of an alternate material are discussed.

Jan 1, 1968

By W. A. Hockings

This report describes a computer program for the solution of material balances in complex mineral processing flowsheets. The program, which is entitled MBS Metallurgical Balance System), evolved as the culmination of a series of material balance programs whose development began in 1967 at the Institute of Mineral Research, Michigan Technological University. The need for such a program became evident when the Institute became heavily involved in a large number of short-term pilot plant projects. Calculating material flows from analytical data by means of the standard two-product formulas grew increasingly difficult and time-consuming as the complexity of the flowsheets increased and as choices between conflicting analytical values had to be made. It was recognized that what was needed was a program that would assimilate all of the available data and calculate mass flow rates so that steady-state inputs and outputs would balance at each point in the flowsheet. Such a program should be capable of handling underdetermined, overdetermined and mixed systems, and when the given data are inconsistent, the program should adjust the data in such a manner that the adjustments are minimized. Missing analyses should also be calculated whenever possible. In addition to solving material balances, the program should be convenient to use and print out the results in a useful form. Thus, the inputting of data should be simple enough to be handled by relatively untrained personnel with diagnostic messages being printed out to identify errors and anamolous data when they occur. Most importantly, the program should produce well-formatted output which can be directly included into a report without the necessity of retyping. The proper spacing of table titles, column headings and the ability to control the columns being printed are important features in this respect.

Jan 1, 1977

By Vaughn Astley, Hassan El-Shall, Ponisseril Somasundaran, Regis Stana, Patrick Zhang

In the past, when phosphate rock quality was good, few paid attention to any of the impurities or other qualities associated with phosphate rock. In general, they had little or no effect on the ability to make the phosphate products for the market. However, as phosphate rock quality declined, it was apparent to the rock consumers that the individual impurities had a significant impact on their processes. FIPR is presently funding an analysis of operating plant data to determine the range of the effects of rock impurities on production plant performance. The study will not be completed until 2002. IMC has agreed to share some of the information they had developed in the early 1990s.

Jan 1, 2002

By D. L. Schweyer, W. A. Munson, R. H. Hanewald

Discussed is the INMETCO processing of electric arc furnace (EAF) baghouse dusts from the specialty-steel and low-alloy industries. In addition, the INMETCO process has been modified to recover nickel, chromium and iron from many other waste materials including: •pickling solutions or filter cakes, •spent nickel and chromium plating baths, •carbon refractories from pickling tanks, and •superalloy wastes including baghouse bags. INMETCO is the only North American company presently capable of recycling nickel-cadmium batteries by high-temperature metals recovery. This process and the details of INMETCO's best demonstrated available technology (BDAT) test program are discussed.

Jan 1, 1993

By Joseph E. Worthington

Increases in the price of gold starting about five years ago, and rapid fluctuations since then, have caused a substantial popular interest in the noble metal. Gold prospecting had been at low ebb since the end of World War II in most of the United states except for a flurry of activity in Nevada occasioned by the Carlin and Cortez discoveries. The last five years, however, have seen a great awakening of interest in gold exploration as well as an opportunity for education for many explorationists in the geology and other vagueries of gold deposits. The present writers have participated over the last few years in a search for gold deposits throughout the United States. This search was greatly influenced by the geologic studies of Dr. Wm. Spence at the Haile Gold Mine in South Carolina as reported in a companion paper. Spence's studies resulted in definition of a geologic model that has proven useful in a number of other geologic environments in the united states. These programs were all carried out under the auspices of Cyprus Mines Corporation and permission by Cyprus to present these results is gratefully acknowledged. The writers, however, reserve for themselves all responsibility for the results and conclusions. The exploration program to be described began in the southeastern United States. Spence's studies provided a reasonable basis for interpreting and understanding the geology of the Haile deposit and also provided a means for predicting additional occurrences. This concept was then expanded to other gold occurrences in the Piedmont and became an effective tool for evaluating other prospects. Finally it became evident that the concept could be applied in some western gold districts. The following discussion will then include descriptions of other Piedmont examples and a few western districts that also appear to fit the pattern.

Jan 1, 1978

By R. L. Bullock

The New Lead Belt of Missouri, situated in the heart of the Clark National Forest, stands as a dynamic example of how mining activities can successfully coexist in a restricted wilderness area. After 16 years of intensive drilling activity, mine development and surface plant construction, many would agree that the mine-plant design philosophy of St. Joe has minimized the imbalancing effects to the ecology and the wilderness appearance of the Ozark area. In a recent dedication speech of St. Joe's newest operation, it was stated: 1 "this Brushy Creek Mine, as well as nearly all of the mines in this district, lies within the boundaries of the Clark National Forest. Here the Forest Service has an outstanding and realistic program for multi-use of Federal lands. Mining, lumbering, recreation and conservation coexist in, what I consider, a delightful wilderness environment. I believe that this same type of usage could be permitted on all government land without seriously detracting from its natural beauty." Each and every activity in the process of discovery, exploration, development and finally operating a mine and process mill could have drastically degraded some phase of nature's environment were it not for the well developed and executed plans of the mining people involved. This is not to say that everything has been kept in perfect balance; but most certainly the industrial impact on what was once a wilderness area has been held to a minimum. What follows is the story of how each phase of this gigantic development was handed by industry people. Through their interaction and cooperation with government agencies, educators and researchers, allowed not only the ecology of the area to be protected, but the aesthetic beauty of the Ozarks to remain intact.

Jan 1, 1973

By B. C. Cornilsen, X. Shan, D. H. Carlson, J. H. Johnson

Airborne respirable Diesel Particulate (DP) presents an additional health hazard in that it has been shown to be mutagenic. This problem is of increasing concern as more coal mines introduce diesel vehicles. If the DP present in coal mine air is to be controlled it must first be measured. This paper describes development of the laser Raman spectroscopic measurement of the amount of DP in DP/coal mixtures collected on filters in the laboratory and in coal mines. The Raman technique provides a chemical measure of the carbonaceous material in each component, and is not dependent upon particle size. When this work was begun there were no known analytical methods for this measurement. Side-by-side in-mine comparisons of the results obtained from Raman, neutron activation analysis, and size selective analyses (MOUDI and personal samplers) are presented. The neutron activation and size selective analyses were obtained by the USBM Twin Cities Research Center and University of Minnesota. Good agreement has been found among these three methods.

Jan 1, 1991

By Victor F. Hollister

This report summarizes data available on the Fort Knox gold deposit to the end of 1989. It is presented courtesy of Fairbanks Gold, operator of the Fort Knox mine. The ore body and the data base are being expanded in 1990, but this summary is pertinent for inclusion in a case history volume that, in part, stresses porphyry-type deposits. Fort Knox is a pluton-hosted gold deposit 22.5 km (14 miles) northeast of Fairbanks, AK. It is easily accessible from Fairbanks, and ultimately it will be the largest open pit gold mine in Alaska. The Fort Knox pluton has an interesting historical record, and it has been discovered at least twice. Fig. 1 shows the geology and location of major plutons in the Fairbanks mining district.

Jan 1, 1991

By G. Johnston, P. K. Chatterjee, S. Holguin

Underground mine planning is largely manual and can demand considerable resources to generate a working plan and to perform limited tests of sensitivity to variations in geological and mining conditions. It is possible to use computer aided mine planning to automate many of the manual procedures to allow the planner to evaluate a number of layouts, extraction strategies, and schedules. his paper examines the simulation and scheduling of an under- ground coal mine operation through the-use of on- screen graphics. The simulation will provide a basis for predicting productivity and other relevant information over a specified number of shifts. The software developed is extremely user friendly and reduces the tedium of repetitive manual calculations inherent to mine planning and drafting to a minimum, thus offering considerable savings in an area that is widely recognized as extremely labor intensive.

Jan 1, 1988

By James P. Connell

The American Concrete Institute defines "shotcrete" as "mortar or concrete conveyed through a hose and pneumatically projected at high velocity unto a surface." This definition thus includes what is traditionally known as "gunite," which is a pneumatically applied mortar. In mining practice, the term shotcrete is restricted to pneumatically applied concrete, and this differentiation will be used in this paper. In 1914, following the invention of the mortar gun in 1907, the then Chief Engineer of the U.S. Bureau of Mines, George Rice, developed the guntie process for underground test work at the bureau facility at Bruceton, Pennsylvania. After World War I, gunite was used extensively in American mines and was also utilized for underground civil works such as the San Jacinto Tunnel in California. The greatest development was In Europe where, as early as 1911, gunite was successfully used as an overlay for deteriorated tunnel linings. In 1951, the Swiss firm Aliva developed a pneumatic gun capable of handling coarse aggregate, thus making possible the first use of shotcrete at the Maggia hydropower development. Intially, shotcrete was used to reduce manpower requirements for forming; and placing conventional concrete. However, by 1954 Sonderegger was reporting that the structural advantages of shotcrete were derived from its flexibility and from the fact that it could be applied almost immediately niter the opening had been made. The incorporation of wire mesh into the shotcrete led to the New Austrian Tunnel Method, or NATM. The use of shotcrete in American mines has been implemented more recently. This delay seems to be due to previously unsuccessful experiences with gunite as a structural material and to the U.S. reliance on wood or steel supports in main line haulageways. The long experience with the apparently more substantial rigid supports led mine operators to be reluctant to the new and seemingly unrealistic lighter shotcrete support.

Jan 1, 1977

By M. Josick Comarmond, Paul L. Brown, Greg P. Timms, A. Ian M. Ritchie, John W. Bennett

Geochemical kinetic models have only become available in recent years and their utilisation in the prediction of effluent chemistry from sulfidic waste rock piles is even more recent. The models used to date, however, have incorporated some questionable assumptions. This paper shows how geochemical, mineralogical and physical field data have been coupled to remove some ill-founded assumptions in the construction of a geochemical kinetic model. Further, the paper discusses a comparison between the observed effluent chemistry from a waste rock dump at the Rum Jungle copper/uranium mine in northern Australia with model predictions. In general, there is good agreement between the two, although an anomalous result is discussed.

Jan 1, 2000