Search Documents

By R. L. Rickett, W. C. Leslie

The influence of deoxidation practice, prior thermal history, and aging time and temperature on the strain-aging behavior of low-carbon open-hearth steels was investigated. The criterion of aging employed was the increase in yield strength in the tensile test, after straining and aging. Composition, prior heat treatment, and aging conditions were all found to be important in governing the strain-aging characteristics of these steels. THAT deoxidation changes the strain-aging propensities of low-carbon steels has been known for a long time, but there has been little agreement, and even contradiction, between results obtained by different investigators and between results obtained in the laboratory and in the mill. This investigation was begun in the hope that some of the uncertainties connected with the strain aging of commercial steels could be eliminated. In considering this problem, it was necessary to define strain aging and to examine the methods used to measure this property. Strain aging can be defined as the changes in properties of a metal or alloy with time, after cold working. The rate at which these changes occur increases as the temperature is raised above atmospheric. The requisite plastic strain is the principal distinction between strain aging and quench aging, the latter being due to precipitation from supersaturated solid solution. Strain aging is also characterized by rapid attainment of maximum hardness at high aging temperatures and lack of softening (overaging) at low aging temperatures. Several possible criteria of strain aging have been listed by Sachsl and by Davenport and Bain.' Because changes in mechanical properties are the most easily measured and the most commonly used, consideration of methods to be used in this investigation was confined to three tests: tensile, notch-impact, and hardness. Hardness tests are the most economical and easiest to perform, but produce only one measure of strain aging. Also, as pointed out by Felmly, Hartbower, and Pellini,³ hardness changes due to aging are not pronounced for steels containing more than 0.15 pct C. Notch-impact tests require careful preparation of large numbers of specimens. Above and below the transition temperature the test lacks sensitivity; furthermore, it is extremely difficult to impart a uniform strain to the specimens, followed quickly by aging and final testing; machining must generally take place after straining. For these reasons, the tensile test was selected for use. Although this test requires a considerable expenditure of time, labor, and money in preparation of the specimens and performance of the test, more information can be gained than from any other single mechanical test, information which includes upper and lower yield points, yield-point elongation, tensile strength, strain-hardening exponent, reduction of area, and elongation. Low and Gensamer' and Schwartzbart and Low5 lso used the tensile test, taking the increase in flow stress after straining in tension and aging as a measure of strain aging. In our work, as in theirs, each specimen was strained an arbitrary amount, sufficient to pass through the

Jan 1, 1954

By M. E. Nicholson

The effect of boron on the austenitic transformation rate of iron is smaller than on low carbon steels. The influence of austenitizing temperature on B-Fe is the reverse of its influence on steels. THERE have been many studies made of the influence of boron on the hardenability of steel, but apparently none has been made of its influence on the y-a transformation of pure iron. There are several facts suggesting that boron should have a pronounced effect on the transformation rate of iron. First, Simcoe et a1.l indicated that boron reduces the nucleation rate of ferrite and bainite. Second, they showed, along with others,', " that the lower the carbon content of steel the greater the influence of boron on hardenability. If this trend extends to pure iron, the influence on rate of ferrite formation should be considerably greater for iron than for medium carbon steels. According to Rahrer and Armstrong," the multiplying factor for boron in pure iron should be about 2.40, compared with 1.50 in a 0.35 pet C steel. According to an extrapolation made by Grange and Mitchell,' the effect should be even greater, and the multiplying factor should be about 3.5 in iron. Many investigations of the boron influence'.7, 2, 5 indicated that boron is effective only when in solid solution. On the other hand, Chandler and Bredig" suggested that boron increases hardenability by combining with nitrogen, thereby preventing formation of AlN, which catalyzes the decomposition of austenite. If their hypothesis is valid, boron should have no effect on an alloy free from nitrogen. Digges et al." showed that so far as low nitrogen high purity Fe-C alloys are concerned this is not the case. No experiments, however, have been made on low nitrogen iron. To determine whether or not boron has an effect on low nitrogen iron and, if an effect exists, to determine whether it is as large as predicted from the investigations of boron treated steels, the following work was performed. Because of the rapidity with which iron transforms from austenite to ferrite at even a moderate degree of supercooling, it was decided to study the influence of boron on the transformation rate of iron by determining the effect of quenching rate on the temperature of the beginning of transformation. The technique, essentially that used by Greninger' and Duwez,H consisted of heating small specimens, 0.1 in. sq and 0.010 in. thick, in an atmosphere of purified helium with a resistance heater coil, and then quenching the sample in a jet of helium gas. At the time the jet was applied, the heating coil was removed from around the sample. The sample was suspended in the furnace on 30 gage chrome1 and alumel wires, one welded to each side of the specimen, which also served as a thermocouple for measuring the specimen temperature. Specimens were prepared from vacuum-melted iron obtained from the National Research Corp. which was rolled to a thickness of 0.060 in. and then decarburized in wet hydrogen for 51/2 hr at 700°C. This treatment also removed any boron present in the iron. The resulting iron contained 0.001 pet C. 0.0002 pet N, and 0.005 pet 0. One half of the piece was then boronized by surrounding it with 325 mesh boron powder and heating it for about 2 hr at 900°C in H,. The boronized iron was then homogenized at 1100°C for 24 hr. The iron boride case formed by boronizing was removed by grinding 0.010 in. from each side of the plate, and the piece was finally rolled to a thickness of 0.010 in. The resulting alloy contained

Jan 1, 1957

By D. J. DeLazaro, W. Rostoker, R. E. Riley, M. Hansen

At very low concentrations, carbon dissolves interstitially in molybdenum resulting in a linear expansion of lattice parameter with increase of carbon in solid solution. Geometrical consideration of the relative size of carbon atom to size of interstice approximately predicts the observed volume expansion. THE element carbon, occurring in molybdenum, either as an unavoidable impurity, or purposely added, markedly affects the mechanical properties of molybdenum. Several investigators1-" have noted the occurrence of molybdenum carbide at the grain boundaries of cast molybdenum, and Fischer and Rengstorff' have shown that this intergranular constituent can induce intergranular brittleness. The appreciable change, with temperature, of the solid solubility of carbon in molybdenum, found by Few and Manning," suggests other important effects upon mechanical properties. Finally the relative atom diameters of carbon and molybdenum (the ratio of atom diameters is 0.59) are indicative, by analogy with iron (ratio of carbon atom diameter to iron atom diameter is 0.65), of a possible interstitial solid solution. If carbon dissolves intersti-tially in molybdenum, anelastic effects and age-hardening effects, similar to those observed in other body-centered cubic metals, could be expected. However, from the work of Sykes, Van Horn, and Tucker," it might be inferred that carbon forms only a substitutional solid solution with molybdenum. These considerations made it desirable to study the effect of carbon on the lattice parameter of molybdenum in greater detail than heretofore. All heat treating was done in a high temperature furnace7 built specifically for heat treatment of molybdenum. The temperatures and times of heat treatment were determined from the a solubility limit for the Mo-C system." These heat treatments were carried out in argon which was purified with respect to N, and H.!0." Purification of the argon was accomplished by passing the argon over hot (750°C) titanium and then through a magnesium perchlorate drying tower. As many as six samples were run concurrently and quenched at different times without interrupting the furnace cycle. Both the purity of the furnace atmosphere and ability to quench samples from any temperature up to 4000 °F were of prime importance in the successful heat treatment of samples for the lattice parameter investigation. Carbon Analysis The Leco Combustion apparatus was used for carbon analysis. This apparatus is capable of an accuracy of & 0.003 pct for a 1 g sample in the range below 0.10 pct. However, it is felt the degree of accuracy is somewhat better than this limit in view of the consistency evident by cross checking a number of determinations. The Battelle Analytical Laboratory consistently reported check results to within k 0.001 pct C. X-ray Measurements The molybdenum wire specimens (20 mils) were carefully filed down to about 12 mils and then etched with nitric acid to 8 mils. Carbon analyses were made on specimens before reduction in size; however, since there was no evidence of surface carburization, it is probable that the carbon was uniformly distributed throughout the sample. The resultant specimens were strain free and small enough to minimize the error in the lattice parameter determinations due to X-ray absorption. Diffraction patterns were obtained with a Debye-Scherrer powder camera 114.59 mm in diam utilizing the Straumanis type asymmetrical film mounting. Nickel-filtered copper. Ka radiation and zirconium-filtered molybdenum Ka radiation were used. Line positions on the film were measured with a traveling microscope equipped with a vernier scale permitting measurement to 0.001 cm. The average of five readings was used to determine the position of each line. The lattice parameter for each specimen was determined from the data by the extrapolation method of Bradley and Jay, Y.e., the intercept at 90" of the straight line obtained by plotting the apparent lat-

Jan 1, 1953

By J. W. Freeman, E. E. Reynolds, A. E. White

Fram a study of 63 systematic alloy modifications it was found that molybdenum, tungsten, and columbium, added individually or simultaneously, and increases in chromium cause major improvements in 1200°F rupture strengths of Cr-Ni-Co-Fe base alloys. Rupture strengths were a function of the effect of composition modifications on both the inherent creep resistance and the amount of deformation the alloy would tolerate before fracture. THIS paper describes the results of an investigation of a series of alloys with systematic variations of the chemical composition of the following basic alloy: C, 0.15: Mn, 1.7; Si, 0.5; Cr, 20.0; NI, 20.0: Co, 20.0: Mo, 3.0; W, 2.0; Cb, 1.0; N, 0.12; Fe, 32.0 pct. The 62 modifications of this alloy were produced under conditions which minimized all factors influencing properties at high temperatures except composition. Melting, fabrication, and heat treatment were carefully maintained constant. Stress-rupture properties at 1200°F were used as the primary criteria of evaluation of the alloy. The objective of the study was to obtain data for determining the fundamental role of the influence of alloying elements on properties of heat-resistant alloys at high temperatures. In addition the results should be useful in determining optimum chemical compositions, the sensitivity of properties to variations in composition, and the degree to which alloy content could be reduced while retaining worthwhile properties. It is difficult or impossible to develop correlations between properties at high temperatures and systematic variations in chemical composition from published data for wrought heat-resistant alloys developed for gas turbines.' ' The main reason for this is the extreme dependence of the properties on conditions of treatment of the alloys." In most cases variation in final treatments between alloys so influences the properties that the influence of chemical composition is obscured. In addition it is recognized Table I. Basic Alloy and Some Modifications Used Basic AllOy, Variations in Element Pct Composition, Pct C 0.15 0.08. 0.40. 0.60 Mn 1.1 0.03,0.25.0.50,1.0,2.5 S1 0.50 1.2, 1.6 Cr 20.0 10, 30 Ni 20.0 0, 10,30 Co 20.0 0. 10, 30 MO 3.0 0. 1.2.3, 5, 7 W 2.0 0, 1, 5, 1 Cb 1.0 0.2,4,6 N 0.12 0.004, 0.08, 0.18 Fe 32.0 that variations exist between heats of the same alloy which are related to melting practice and that there is a strong possibility that conditions of hot working influence response to final treatments. The development of heat-resistant alloys has been based on the gradual accumulation of data roughly related to composition from extensive testing programs. There is every reason to believe that in most cases the optimum compositions have been achieved by this procedure in the alloys commercially available. There are, however, very little data showing the influence of systematic variations of composition free from the influence of other factors, particularly for alloys of the type investigated. Several investigators of cast alloys have demonstrated compositional effects, notably Grant,1-6 Epremian,t Guy,8 and Harder and Gow.9 Sykes10 eviewed the work on the wrought alloy Rex 78 and the systematic variations of carbon, copper, molybdenum, and cobalt leading to the development of the stronger Rex 337A alloy. From the papers by Wilson11 and Henry12 it is possible to deduce the beneficial effect of substituting cobalt for iron in 0.45 pct C-20 pct Cr-20 pct Ni-4 pct Mo-4 pct W- 4 pct Cb alloys. Wilson mentioned but did not present the extensive compositional studies involved in developing these alloys. Binder" showed optimum properties for 3, 2, and I pct, respectively, for molybdenum, tungsten, and columbium in 20 pct Cr-20 pct Ni-20 pct Co-30 pct Fe alloys for limited systematic variations of these

Jan 1, 1953

By D. Coutsouradis, L. Habraken, P. Nicolaides

The TTT curves of 0.1 pct C, 13 pct Cr steels containing up to 12 pct Co have been determined in order to establish whether the effect of cobalt is similar to that observed m plain carbon steels. It is shown that cobalt increases the incubation time and decreases the transformation rate, though not in an uniform way. The bainitic transfornation is displaced to lower temperature and overlaps partially the martensitic zone. ThE effect of cobalt on the transformation of a plain carbon austenite has been studied by many investi-gators.'-3 It was shown that cobalt displaces the TTT curves to shorter times and diminishes the harden-ability. The interpretations given for this effect of cobalt are conflicting. According to E. Houdremont,4 cobalt increases the transformation rate of austenite because it increases the diffusion of carbon as shown in the experiments of E. Houdremont and H.Schrader,' R.Smoluchowski,5 and M. Blanter.6 On the other hand, M. Hawites and R. Mehl3 deny on the basis of their own experiments any effect of cobalt on the diffusion of carbon and they assume that an explanation should be found in an eventual effect of cobalt on the mechanism of nucleation and growth of pearlite. W. C. Hagel, G. M. Pound, and R. F. Mehl7 have shown by calorimetric measurements that cobalt increases the free energy of the austenite-pearlite transformation in an eutectoid steel and this result explains qualitatively the observed effect of cobalt on the rate of nucleation and growth of pearlite. The purpose of this research was to see by determination of TTT curves, if this same effect exists in 13 pct Cr steels. EXPERIMENTAL PROCEDURES The preparation of the alloys was carried out in an

Jan 1, 1960

By D. H. Thompson, A. W. Tracy

Season-cracking is a type of failure of brass that results from the simultaneous effect of stress and certain corrodants. The object of this paper is to present data that will aid in a more complete understanding of the mechanism of season-cracking and related phenomena. Results presented show that certain high copper alloys are susceptible to season-cracking or stress-corrosion cracking, and possible explanations are discussed. Starting at least as far back as 1906, many papers have been devoted to this subject but the symposium1 held in Philadelphia in 1944 is the richest source of information. In order to study season-cracking, several of the many variables were held constant so as to learn the effects of others. Season-cracking is generally understood to refer to the corrosion cracking of brass having internal stresses;²,³ it is a special case of the general stress-corrosion cracking. Inasmuch as applied stresses are more readily produced and controlled, they were used exclusively in this research and the resulting phenomenon must he called stress-corrosion cracking.²,³ Only constant tensile stresses were used. The agents believed to be most frequently responsible for season-cracking are ammonia. amines and compounds containing then]. Both moisture and oxygen also appear to he necessary. Therefore, an atmosphere containing ammonia, water-vapor and air was selected for these tests. Briefly, the work consisted of exposing sheet metal specimens, having a reduced section ¼ by 0.050 in., of copper-base alloys to the effect of static tensile stresses between 5,000 and 20,000 psi and simultaneous contact with a. continuously renewed atmosphere containing 80 pct air, 16 pct ammonia and 4 pct water vapor at 35°C. The gas mixture and the speci- mens were maintained above the dew-point. The time-to-failure in minutes was the primary measure of results. In order to limit the experiment to finite time, it was considered that a specimen which had neither failed nor undergone microscopically detectable cracking in 40,000 min. (4 weeks) while under a stress of 10,000 psi or more could be considered immune to cracking. This is merely a convenient limit and is not to be considered proof of immunity. Supplementary tests in the absence of stress using weight loss or microscopical appearance as measures of attack were made. Apparatus The apparatus used in this research is shown in Fig 1. To facilitate the description it may conveniently be divided into six parts: stress-producing units, test chamber, gas train, electrical controls, timers and gas analysis device. A stress-producing unit is shown in an exploded view at the left in Fig 2. At the right is an assembled unit with a specimen in place in the lower portion; it is this part that remains in the ammonia atmosphere during a test. The upper part contains a spring, a central threaded rod, a large nut and necessary washers, pins, and so forth. Stress is produced in the specimen by screwing down the top nut against the spring, thus putting a tensile load on the central rod and so on the specimen. The wrench that turns the nut by extending through the upper cap, is seen at the upper right of the figure. The magnitude of the load is gauged by measuring from the pin that extends through the side of the tube, to a fixed point on the large flange. Measurement is made with a vernier beam caliper, shown at the right of the figure. The necessary spring compression to give a desired stress is calculated from the calibration curve of the spring and the dimensions of the specimen. The test chamber, center Fig 1, consists of a thermally insulated steel box 32 in. long by 10 in. high by 7 in. wide. A horizontal baffle reaching nearly to each end divides the chamber equally. Below this baffle are inlets for air and ammonia, a heating coil and a fan. Thus the gases are warmed and mixed in the lower level and flow past the specimens in the upper level. A thermo-regulator and thermometer project into the upper space. The top is pierced by 12 ports flanked by 3/8 in. threaded studs. A test starts when a port is opened and a unit containing a stressed specimen is thrust through it and bolted down against a neoprene gasket. The test chamber is held at 35°C. The gas train, right rear Fig 1, carries ammonia and air continuously to the test chamber. Tank ammonia passes through two reducing valves, a needle valve, a flow meter and into the test chamber. The air from either the plant compressor or a small laboratory compressor passes through wool towers and flow controls to the flow-meter. It then bubbles through water at 34°C and through a heated line to the test chamber. Electrical controls, left rear, Fig 1, provide rectifiers and mercury relays for the test-chamber and humidifier-heating-control circuits and outlets for

Jan 1, 1950

By D. H. Thompson, A. W. Tracy

E. A. ANDERSON*—At the outset, I note that you are using a humid atmosphere containing ammonia but that you make no reference to the variable of carbon dioxide content. Edmunds in his work in this laboratory found very marked effects on the rate of failure due to variations in carbon dioxide in the environment. This point is, of course, strongly related to the overall corrosion rate problem since the role of the carbon dioxide seems to be to permit the formation of hygrogroscopic salts which give a controlled moisture film on the specimen surface, which in turn seems to support the intergranular penetration more consistently than would otherwise occur. (2) Your results with various copper binary systems are very striking. It is curious, however, that the time-to-failure minima all occur at percentages of the alloying element which are considerably below the solubility limits as given in the conventional equilibrium diagrams. If your theory regarding the presence of these impurities in some concentration in the grain boundaries is correct, then either the existing diagrams are not accurate in the room temperature region, or there is a difference in solubility in the grain boundaries as compared -with the grains. A study along these lines might be very revealing. (3) The undesirable effect of silicon in copper calls to mind our own observations on the influence of silicon on the stress corrosion cracking resistance of alpha brass. In this case, silicon was found to have a very marked beneficial effect, particularly when a heat treatment capable of producing a grain boundary constituent was used. I should appreciate it if in the discussion of your paper this point should arise, you would attempt to clarify the difference between the copper-silicon binaries and the copper-zinc-sili-con ternary alloys. D. H. THOMPSON and A. W. TRACY (authors' reply)—(1) We have no data on the constancy of the carbon dioxide content of the air used for the test atmosphere but have believed that the normal carbon dioxide content of the air was as constant as could be obtained by using Edmunds' method of removing carbon dioxide from the air and then adding a measured quantity. In any event, the test atmosphere was the same for all specimens in a test run. We agree with Mr. Anderson that the carbon dioxide content is important in the formation of a hygroscopic film on specimens. (2) We can imagine that there could be a concentration of solute atoms at the grain boundaries which would be so small that present methods would not detect it even if it exceeded the solubility limit of the alloy. There could be somewhat greater solubility at the grain boundaries for an interstitial solute. There is a possibility that phosphorus dissolves in this way but we believe that none of the other solutes studied does. In our present studies we hope to find out something about conditions at the grain boundaries of some of the systems mentioned in the paper. (3) Mr. Anderson points out that silicon brass, which has had a high temperature heat treatment followed by a quench. is highly resistant to stress-corrosion cracking. Although the test conditions used by Anderson* et al were different from our test conditions, it is noted that the silicon brasses which had not had the special heat treatment were less resistant to stress-corrosion cracking than copper containing approximately equal amounts of silicon. G. R. GOHN†—Nonferrous metallurgists and particularly, materials engineers, have been accustomed to thinking

Jan 1, 1950

By R. G. Aspden

Crystals with an (001) [loo] initial orientation of an iron-base alloy containing 3 pct Si were cold rolled with and without the use of constraints. A major difference in the rolling and annealing textures was observed between crystals rolled with and without constraints. These data show that the contribution of constraints at grain boundaries in a poly crystalline sheet should be considered in applying textural data on single crystals to grains in an aggregate. SILICON-iron alloys with a cube texture have been recently developed and their magnetic characteristics reported.1-4 Of interest in the development of this texture were the textural changes of single crystals accompanying rolling and annealing and the influence of constraints at grain boundaries in an aggregate on the behavior of individual grains. The present study was primarily concerned with the effect of constraints during rolling on the textures of 3 pct Si-Fe crystals initially (001)[100]. Barrett and Levenson5 were among the first to observe an influence of constraints at grain boundaries on the textural changes of individual grains during deformation. They tested Taylor's6 theory of plastic deformation of face-centered-cubic metals in which deformation textures were predicted. About one-third of the grains in poly crystalline aluminum did not rotate as predicted. Grains of the same initial orientation were observed to rotate in different directions under the influence of applied stress and anisotropic flow of neighboring grains. Recently, the various inhomogeneities of flow of crystals in an aggregate have been studied7'8 and reviewed.9-11 Barrett and Levenson" rolled (001) [loo] iron single crystals inserted in close-fitting holes in copper to limit lateral flow and to simulate rolling of grains in an aggregate. Deformation bands were formed after a 90 pct reduction in thickness, and the cold-rolling texture contained two components described by rotating the (001)[100] about 35 deg in both directions around the normal of the rolling plane. No annealing textures were reported. Chen and Maddin13 rolled molybdenum single crystals initially (001) [loo]. The crystals were mounted between two hardened silicon-iron plates and 96 pct reduced in thickness by rolling at a low rate of reduction, about 0.0001 in. per pass. The deformation texture had the mean orientation of (001) [loo], and the azimuthal spread included orientations described by rotating (001) [loo] about 35 deg in both directions about the pole of the rolling plane. The presence of deformation bands were not reported by Chen and Maddin or detected in subsequent work of Ujiiye and Maddin.14 The ideal orientation of the annealing texture was (001) [loo]. Recently, Walter and Hibbard 15 reported on the textures of 3 pct Si-Fe alloy crystals initially near (001) [loo]. Each crystal was in an aggregate cut from a columnar ingot. After 66 pct reduction by rolling, the texture consisted of two symmetrical components which had the orientations described by rotating (001) [loo] about 30 deg in both directions about the pole of the rolling plane. Annealing texture was near (001) [loo]. In the above work, the textures of body-centered-cubic crystals were studied after rolling under the influence of constraints. The deformation textures varied from (001) [loo] to near the (001) [110] type and appeared sensitive to the manner in which the crystals were rolled. No textural data were available on the effect of rolling (001) [loo] crystals with and without constraints. The purpose of the present work was to evaluate the influence of constraints during rolling on the textures of 3 pct Si-Fe crystals initially (001) [loo]. Rolling and annealing textures were studied for a) crystals rolled with no constraints at different rates of reduction, and b) crystals rolled with constraints imposed by neighboring grains and by plates between which a crystal was "sandwiched". PROCEDURES AND EXPERIMENTAL TECHNIQUES Data are presented on four crystals which are representative of several crystals studied. The orientation of each crystal prior to rolling was (001) [loo] as determined by the Laue X-ray back-reflection method," i.e., each crystal had an (001) within 3 deg of the rolling plane and [100] within 3 deg of the rolling direction. These crystals were obtained from two iron-base alloys containing 3 pct Si by weight which were prepared by vacuum melting electrolytic iron and a commercial grade of silicon. Crystals 1, 2, and S-1 were cut from a large single crystal grown from the melt of one alloy by the Bridgman technique17 in an apparatus described by

Jan 1, 1960

By J. A. Coll, R. W. Cahn, A. Lawley

WHILE the creep properties of pure face-centered-cubic and close-packed-hexagonal metals have been thoroughly investigated and are well established, body-centered-cubic metals have been studied less extensively. Moreover, very few fundamental studies on the creep of solid solutions, irrespective of crystal structure, have been reported. The present study is concerned with the creep of a series of body-centered-cubic solid solutions. The present position concerning creep of pure metals is, briefly, as follows.1"3 Creep at first takes place at a steadily decreasing rate; this is the stage termed primary or transient creep. Except at the lowest temperatures this is succeeded by a stage of secondary or steady-state creep. At high temperatures and stresses, this may be succeeded by an accelerating stage, termed tertiary creep, with which we shall not here be concerned. There is no well-defined physical model at present for the transient stage; in general terms, transient creep is best regarded simply as a manifestation of work-harden ing. Steady-stage creep can certainly take place by several different mechanisms: the choice of dominant mechanism depends primarily on temperature. We shall here be concerned only with high-temperature steady-state creep, a term usually reserved for creep at absolute temperatures higher than 0.5 Tm, where T, is the melting point. In this range, the activation energy for creep is, for many metals, equal to the activation energy for self-diffusion, and this is generally interpreted in terms of a "climb mechanism.1-4 The creep rate is determined by the speed at which dislocations, impeded by obstacles the nature of which is disputed but which are probably established during transient creep, can climb by means of a diffusion process, until they are able to by-pass the obstacle. In solid solutions, the intrinsic resistance to the slip motion of dislocations may be much larger than in the solvent, to the extent that the motion of dislocations in the glide plane, rather than their escape by climb out of this plane, may become the rate-controlling factor. weertman5 has considered this possibility from a theoretical point of view, and concluded that some form of "viscous slip" is likely to be rate-controlling at comparatively low stresses. The resistance to slip may arise from "atmospheres" of impurities forming around dislocations; a high Peierls force in materials of high cohesion; or some structural peculiarity such as clustering or ordering of solute atoms.= We shall be concerned here with the case of ordering. The only published investigations concerned explicitly with the effect of order on creep refer to creep in ß-brass by Herman and Brown,7 and in Ni-Fe alloys, by Kornilov and panasyuk8 and by Suzuki and Yamamoto.9 Recently, Herman and Brown's paper has been supplemented by a determination of the tensile yield point of ß-brass as a function of temperature.10 Both studies showed a sharp drop in resistance to deformation of ß-brass over a range of a few degrees just above the critical temperature Tc at which order finally disappears. These observations are especially noteworthy, because in ß brass the degree of order diminishes steadzly to zero as the temperature approaches Tc. It is, therefore, the disappearance of the last traces of long-range order which has the largest effect on the resistance of the alloy to plastic deformation. In the Ni/Fe alloys of various compositions, resistance to creep at a given temperature and stress is maximum at the stoichiometric composition, both below Tc, (long-range order), and above T,. (short-range order).' Near Tc, the creep resistance of an ordered alloy is much higher than that of the same alloy in the disordered condition.9 The aim of the present investigation was to study the creep behavior in the neighborhood of Tc, of another system of ordering alloys. The iron-aluminum alloys were considered the most suitable. because: i) The order again diminishes steadily to zero as the temperature approaches Tc; there is no sudden drop in order at Tc, and it therefore is

Jan 1, 1961

By R. H. Frazier, C. H. Lorig, F. W. Boulger

This investigation establishes the effect of ferrite grain size resulting from various heat treatments on the transition temperature of a semikilled steel plate. Different austenitizing temperatures and various cooling rates were used. The ductile-brittle transition temperatures were determined by the Navy tear test and the keyhole Charpy test. THE data presented in this paper deal with quality characteristics of ship-plate material which were investigated in a research project sponsored at Battelle by the Bureau of Ships, Dept. of the Navy. Specifically, the object of this investigation was to establish the effect of ferritic grain size (resulting from various heat treatments) on the so-called transition temperature of ship-plate steel. Transition temperature is not a fixed property of steel. It is derived from a series of static or dynamic tests made at various temperatures and is qualified by specifying the type of test employed as well as the testing criteria. Because in earlier investigations of ship-plate quality1,2 the so-called Navy tear test and standard notched-bar tests (keyhole Charpy) proved to be useful in interpreting instances of brittle behavior of ship plate in service, these tests were used in the investigation reported in this paper. By definition,' in the Navy tear tests the highest temperature at which one or more of four specimens breaks with a brittle fracture (that is, when less than 50 pct of the fracture area has a dull fibrous texture) is termed "transition" temperature. In the Charpy tests, the 12 ft-lb level of energy absorption was used as a criterion indicating the "transition" temperature, although other levels of energy absorption were also used for comparison. Earlier work" on ship-plate steels indicated that the temperature at which ship plate is finished has a very significant effect on its notched-bar properties. Plates rolled in the laboratory, where the finishing temperature can be carefully controlled, showed a 16°F decrease in tear test transition temperature when the finishing temperature was lowered 200°F (from X" to Y°F). The same plates showed a drop of 10°F in the keyhole Charpy transition temperature from the same decrease in finishing temperature. Commercially finished plates' exhibit a similar trend. When the ferrite grain size of the hot-rolled laboratory plates was determined, a close relationship was found between the ferrite grain size and the notched-bar transition temperature." " he indicated relationship between grain size and transition temperature was in agreement with the findings on low carbon steels of Hodge, Manning, and Reichhold' despite the differences in composition of the steels. The cooling rate after rolling varies from one steel plant to another. This variation changes the micro-structure" and appears very likely to affect the notched-bar properties of the steel plates. In the investigation summarized in the present paper, heat treatments simulating finishing practices in the hot rolling of ship plate were used in order to vary the ferritic grain size. It is believed that the indicated relationship between grain size and transition temperatures of the ship-plate material will prove useful in estimating the effect of rolling temperature and of cooling rates from rolling temperatures on the notched-bar properties of semikilled steel plate. Material The semikilled steel plate used in this investigation was a ¾ in. hot-rolled plate from an open hearth heat. Other plates from this heat have been used on many other studies performed for the Ship Structure Committee," "," and the heat has been identified as project steel "A". The chemical composition of the plate1 was 0.25 pct C, 0.49 pct Mn, 0.011 pct P, 0.045 pct S, 0.04 pct Si, and 0.004 pct N.

Jan 1, 1956

By Howard Reiss, C. S. Fuller

A theoretical and experimental study has been made of those interactions between holes and electrons which influence the solubilities of donors and acceptors in semiconductors. The major portion of the work concerns the solubility of lithium in silicon doped to varying degrees with boron. This solubility increases with increasing boron content in a manner predicted by theory and exhibits the expected temperature dependence. A qualitative experiment in germanium is described which demonstrates, in accordance with theory, that doping with a donor decreases the solubility of another donor. SEVERAL authors have discussed the possibility that holes and electrons behave like chemical entities and influence the solubilities of ionized impurities, Wagner was the first to invoke this concept in connection with his studies on nonstoichio-metric oxides. He used it again in explaining the solubility of hydrogen in molten binary alloys. In a theoretical paper,' Reiss drew attention to the fact that solutions of impurities in semiconductors

Jan 1, 1957

By S. F. Ramseyer, E. A. Steigerwald

INFILTRATED structures represent composite materials which are capable of combining high-temperature strength with adequate low-temperature toughness and thermal shock resistance. Although copper- and silver-infiltrated tungsten structures are actually being used in rocket nozzle hardware, adequate understanding of the fracture mechanics of these composite systems is not available. Specifically the relative importance of the strength, ductility, and modulus of the infiltrant in determining composite properties is not known to the extent that optimum composites can be selected. The major portion of experimental effort in the area of composite strength has been devoted to fiber-reinforced systems1 or to systems where a discontinuous phase is imbedded in a relatively ductile matrix.2'3 In the case of high-temperature systems, which are composed of a relatively brittle matrix, such as tungsten or an oxide, a continuous phase exists for the propagation of a crack. The method by which the presence of a conjugate ductile continuous phase influences the gross properties of the composite represents an area which requires further investigation. This technical note presents results which evaluate the effect of infiltrant strength on the strength of the tungsten-base composite. A tungsten matrix and copper-base infiltrant were selected for the initial studies because of the ease of fabrication. Tungsten structures with nominally 20 and 30 pct porosity were evaluated. The porosity was controlled by varying the initial powder size and a ratio of open-to-total porosity greater than 95 pct was obtained by selective sintering cycles. The processing sequence involved hydrostatic pressing followed by a 72-hr presinter in hydrogen at 2000° F and a final sinter at 4000°F for 4 hr in vacuum. The 20 pct porous structure was obtained

Jan 1, 1965

By Craig R. Barrett, Alan J. Ardell, Oleg D. Sherby

It is shown that the apparent activation energy for creep of pure poly crystalline metals increases with increasing temperature in the temperature range 0.5 to 1.0 of the absolute melting temperature. This increase is probably associated with the influence 0-f the elastic modulus on the creep rate. By accounting for the variation of Young&apos;s nodulus with temperature, the true activation energies for creep of pure cadmium and aluminuvl are shown to be equal to the activation energies for self-diffusion in these metals, within experimental error, at all temperatures above 0.5T,. New creep parameters are proposed for cmrelation of steady-state creep rate and time-to-rupture data. These are respectively, where u is the creep stress, E is Young&apos;s rrodulus, i,is the steady-state creep mte, t, is the time -to-rupture, and D is the self-diffusion coefficient [equal to Do exp (-QSd/RT)] . It has been established experimentally1 and theoreticallyZm4 that high-temperature creep of poly-crystalline pure metals is a thermally activated process and may be represented by the general expression where <, is the steady-state creep rate, A is a constant dependent on the internal structure of the material, f is some function of the applied stress (0) and test temperature (T), and D is the self-diffusion coefficient. If D is separated into its temperature-dependent and independent portions, then it is possible to rewrite Eq. [I] as where Qsd is the activation energy for self-diffusion. Assuming a simple Arrhenius-type relationship between creep rate and temperature at a given constant stress, the apparent activation energy for creep, Q,, is given by the expression It is obvious that if is not a function of temperature It has been shown that the steady-state creep rate for pure polycrystalline metals1 can be represented by where S is a constant, L is the grain diameter, E is the isotropic polycrystalline (unrelaxed) elastic modulus, and n is a constant equal to approximately 5 over a wide range of stress. The apparent activation energy for creep calculated from this expression at constant grain size and stress is given by

Jan 1, 1964

By N. J. Grant, K. M. Zwilsky, J. T. Blucher

DISPERSION strengthening has been studied in a number of metal-metal oxide systems. To date those pure metals available as fine particles (less than about 5 p) have received most of the attention whereas solid solution alloys, generally unavailable as fine powders, have not been examined in detail. The present work was undertaken as a preliminary study to evaluate combined effects of solid solution and dispersion strengthening. The technique used was that of dry mixing of elemental powders with the oxide, followed by a diffusion treatment to obtain the solid solution. The average particle size of the powders used was: Ni, 3.2 p (1nco B); Mo, 1.3 p (Fansteel Metallurgical Corp.); and y alumina, 0.027 \i (G. L. Cabot, Inc.). The particle size of the metal powders was determined by Fisher subsieve measurements while the size of the alumina was calculated from a surface area determination. Prior diffusion studies on small compacts pressed from mixtures of nickel and molybdenum powders with and without 7.5 vol pct A1203 indicated that diffusion was complete after sintering for 100 hr at 1800" , or 50 hr at 2250", or 20 hr at 2550° F. The progress of diffusion was followed by microstructural examination and micro-hardness measurements. Two observations made during the diffusion experiments were: 1) That diffusion proceeded faster in the presence of alumina, confirming similar findings by Seith and Loepman on "SAP&apos;&apos;;4 2) That diffusion at temperatures above 1800°F resulted in coarsening of the alumina in agreement with results of other authors reporting on the growth of alumina in nickel above 1800"F. Similar experiments in the Ni-Cr system using 6 and 20 p Cr powders of 0.7 and 0.025 pct 0, respectively, did not result in significant solid solution formation even after long time exposures at 2550° F. It must be concluded that chromium oxide films around individual particles interfere with normal diffusion. A nickel alloy containing 5 wt pct Mo and 7.5 vol pct alumina was fabricated by dry mixing of powders, isostatically compacting at 30,000 psi, diffusing for 120 hr in dry hydrogen at 1800" F, and extruding at 1950"~ with a 30 to 1 reduction of area ratio. The resulting structure, presented in Fig. 1

Jan 1, 1963

By N. Brown, M. Herman

ORDERING&apos;S effect on the creep strength and other plastic properties of metals is unknown at the present time. Sachs and Weerts&apos; attempted to compare the mechanical properties of the ordered and disordered state by comparing a quenched specimen with one annealed for a long time at a low temperature. This experiment is unsatisfactory because it introduces a possible effect from quenching. Barrett&apos; used a hot impact test, but his method was not sufficiently sensitive to indicate any discontinuity in plastic behavior in the neighborhood of the critical temperature. On the theoretical side, Fisher9 as suggested that short range order would strengthen an alloy, but he gives no conclusions as to the effect of long range order. Cottrell" has discussed the interaction between long range order and dislocations, but does not indicate whether slip in a completely ordered alloy without domain boundaries is appreciably more difficult than slip in the disordered state. Because order exists in so many alloy systems, it is most important to prove experimentally whether long range order weakens or strengthens a metal. This investigation used -brass because: 1) it orders

Jan 1, 1957

By H. D. Kessler, R. J. Van Thyne

Phase diagrams of the titanium-rich portion of the ternary systems from 0 to 10 wt pct Al and 0 to 1 wt pct 0, N, and C were determined. Micrographic analysis of annealed high purity arc melted alloys was the principal method of investigation and was supplemented by X-ray diffraction. TITANIUM-ALUMINUM alloys exhibit excellent properties, particularly for elevated temperature use. For this reason, the Materials Laboratory, Wright Air Development Center, sponsored an investigation of the effect of the interstitially soluble contaminants, oxygen! nitrogen, and carbon, on the Ti-A1 system. Using high purity arc melted alloys and micrographic analysis of annealed samples as the chief method of investigation, titanium-rich partial phase diagrams were determined for the ternary systems. Experimental Procedure Materials: The titanium used in the preparation of the alloys was iodide crystal bar (99.9+ pct pure) produced by the New Jersey Zinc Co. and Foote Mineral Co. The aluminum was obtained from the Aluminum Co. of America in the form of sheet. The given analysis was: Si, 0.0006 pct; Fe, 0.0005; Cu, 0.0022; Mg, 0.0003; Ca, <0.0006; Na, <0.0005; and Al, 99.99. High purity titanium dioxide purchased from the National Lead Co. was used in the preparation of the oxygen-bearing alloys. The spectrographic analysis of this material was as follows: SiO,, 0.07 pct; Fe,O,,, 0.002; A1,0,, <0.001; Sb,O,, <0.002; SnO,,, <0.001; Mg, <::0.001; Cb, <0.01; Cu, 0.0004; Pb, 0.002; Mn, <0.00005; W, <0.01; V, <0.002; Cr, <0.002; Ni, <0.001; and Mo, <0.002. Special spectroscopic graphite rod purchased from the National Carbon Co. was used in the preparation of the Ti-A1-C alloys. Alloy Preparation: Alloy ingots weighing 10 grams were melted in a nonconsumable tungsten electrode arc melting furnace using water-cooled copper hearths and a helium atmosphere. The arc was struck on a tungsten stud in the copper block to minimize contamination from the electrode. Details of the techniques have been reported.&apos;, &apos; Each ingot was inverted and remelted a minimum of four times to insure homogeneity, without opening the furnace. Remelting small control ingots of iodide titanium under similar conditions resulted in no measurable hardness increase, indicating contamination-free melting conditions were used. The alloy charges and resultant ingots were weighed to the nearest milligram. Only small weight losses were obtained upon melting, indicating that the actual compositions were very close to the nominal compositions. Check analyses substantiated this. Oxygen and nitrogen were added during ingot preparation as master alloys. An oxygen master alloy containing 25 wt pct 0 was prepared by melting iodide titanium and pressed titanium dioxide (40 pct 0) powder. The Ti-25 pct 0 alloy is more easily handled during weighing and charging than the pressed TiO, powder. Chemical analysis indicated that titanium-nitride received from an outside source contained large amounts of impurities (2.7 pct Ca). Therefore, a master alloy containing approximately 12 pct N was prepared by melting nitrided sponge titanium. As the sponge melted with difficulty, the alloy was diluted by addition of titanium to lower the melting point. The chemical analysis of the final alloy was 6.69 pct N. Both master alloys are friable and were used as —8 +16 mesh lumps resulting from crushing the ingots. NIelting the Ti-A1-0 and Ti-A1-N compositions five times produced homogeneous ingots. The preparation of homogeneous carbon-bearing alloys caused considerable difficulty. Alloys containing less than 1 pct C were prepared using spectrographic graphite rod, 1/8 in. diameter by 1/8 in. long. However, the graphite did not dissolve even with long melting times and many remelts. The ?/s in. pieces of graphite were used rather than powder because the low density powder is troublesome in arc melting.

Jan 1, 1955

Using 5-p Ni powder and 0.018 ,u A1203, oxide dispersion strengthened nickel alloys were prepared by mechanical mixing of powders, followed by compaction, sintering and extrusion. Processing variables such as cooling of the powder during mixing, electrostatic discharging, mixing time, amount of oxide, and so forth, were studied to determine the effects on room-temperature tensile and high-temperature creep-rupture properties and on the reproducibility of alloys. MECHANICAL mixing of metal and metal oxide powders provides one of the simplest and most inexpensive methods for preparing dispersion strengthened metal-metal oxide alloys;" however, because of large differences in specific gravity, powder particle diameters and other variables, difficulties have been encountered in reproducing alloys and alloy properties. Using 5-p Ni powder and 0.018 p A1203, the following variables were investigated: a) Blending techniques b) Blending time c) Volume fraction of oxide for the selected pow- ders d) Sintering of compacts before extrusion Cooling of Powders During Blending— Cremens and Grant had indicated that dry ball milling of the powder mixture gave superior results over other procedures. When ultra-fine metal and oxide powders became available and comminution was unnecessary or offered little gain, the use of dry mixing in a Waring Blendor gave optimum results.&apos; In the current study, observations of the powder mixtures indicated that considerable heat was generated due to the high speed of the Waring Blendor (15,000 rpm). This heating appeared to produce some degree of clustering and pelletizing. To minimize such agglomeration, a Pyrex cooling coil was installed in the mixing vessel. A double coil, water cooled, proved to be quite satisfactory, providing a fair degree of cooling along with good erosion resistance. Discharge of Electrostatic Charge—Electron-microscopy showed that agglomeration was minimized by the cooling procedure but was not entirely eliminated. It appeared that some of the ag- glomeration had to be explained on the basis of an electrostatic attraction due to the high-speed blending operation. These charges had the effect of promoting the growth of alumina clusters. At the end of the blending procedure such clusters had an effective size which was as much as 50 times that of the individual powder particles and were very tightly bunched. Several methods were utilized to try to discharge the electrostatic forces to minimize the clustering. One successful method, utilized in alloy 17, involved continuous exposure during blending to a radium source of 50 millicuries at a distance of 1.5 ft from the container. A number of other methods were noted to work equally well. Fig. 1 shows the more open oxide structure which results from such a treatment, permitting the matrix metal to penetrate into the cluster more effectively. The combination of powder cooling and discharging led to noticeably improved structures. Fig. 2 shows a cross and a longitudinal section in alloy M-17, one of the best alloys, illustrating the marked decrease

Jan 1, 1961

By R. H. Frazier, C. H. Lorig, F. W. Boulger

THERE are both advantages and disadvantages in using semikilled steels in place of killed steels. One advantage of semikilled steels is they provide a higher ingot-to-product yield. This is especially important to shipbuilders in the time of national emergency. By using semikilled steel for hull plates, a greater number of ships can be built from the same ingot tonnage. Consequently, if semikilled steel plates are adequate for the service, the advantage of the higher product yield is of considerable importance. The performance of hull plates is closely associated with the ductile-to-brittle transition temperature, and this, in turn, is strongly dependent on the composition of the steel. A low transition temperature is desirable because it indicates that the steel is less likely to fail at low ambient temperatures. Killed steels are known to have lower transition temperatures than semikilled steels. It is believed that the better qualities of killed steels in this respect are due mainly to the low oxygen contents of the steel. The principal deoxidizers, aluminum, silicon, and manganese, lower the oxygen content. Fundamental studies1-0 have shown that the oxygen content remaining after the addition of one of these three elements is influenced by the residual amounts of the other two present. In the current study, therefore, various amounts of silicon and aluminum were added to steels containing different manganese contents for the purpose of studying the influence of silicon and aluminum on the notched-bar properties of hot-rolled steels. Eleven types of steels were studied. The temperature at which the plates were finish-rolled was care- fully controlled at 1850°F. All plates were rolled to ¾-in. thickness, and tested in the as-rolled condition. The total number of steels prepared in the laboratory for this study was 95. The charge consisting of ingot iron and ferrosilicon equivalent to 0.10 pct Si was melted in a 200-lb induction furnace under an atmosphere of argon to insure low, uniform nitrogen contents. After the charge was melted and the desired temperature was obtained, the melt was partly deoxidized with either silicomanganese or aluminum. Aluminum was used for this purpose in only those steels with very low silicon contents, where the finished steel was to contain some aluminum. This initial deoxidizing addition was made to obtain consistent recoveries of subsequent additions of ferro-manganese, ferrosilicon, and aluminum. Carbon, in the form of graphite, was added, either just prior to tap or to the final aluminum addition. The entire heat of 200 lb was poured directly into a 6x6-in. big-end-up mold. The ingots of semikilled steel were capped with a steel plate. The killed steels, on the other hand, were poured with a hot-top containing 14 pct of the total volume of the ingot. The ingots were processed by heating to 2250°F, followed by forging to slabs 1¾ in. thick and 6 in. wide. After reheating to 2250°F, the slabs were rolled to 0.9-in. gage, using reductions of approximately 1/6 in. per pass. The 0.9-in. thick plates were immediately recharged in a furnace held at 1850°F. After 30 min in the furnace at 1850°F, the plates were rolled to ¾ in. in one pass. Following the final pass, the plates were stacked on edge on a brick floor, with a brick separating one from another, where they were allowed to cool in air. Drillings for chemical analysis were taken from the plates at locations corresponding to the top and bottom of each ingot. Carbon, manganese, silicon, phosphorus, sulfur, and nitrogen contents of each sample were determined. The analysis of each steel was carefully controlled so that the contents of

Jan 1, 1957

By F. Bonaccorso, G. Venturello, C. Antonione

A study of the effect of small amounts of interstitial impurities on recovery and re crystallization in high-purity iron (99.995 pct) has been undertaken. This paper gives results on the effect of carbon, introduced in small-dosed amounts @om 0.0005 to 0.0086 wt pct) by heating iron specimens of high purity m a static atmosphere of CO + ,. The materials prepared in this way, cold-worked 80 pct and subjected to a series of isochronal and isothermal annealings, were submitted to examinations by X-rays, micrographs, and hardness tests. It was observed that effect of carbon is remarkable in the sense of blocking recovery of mechanical properties up to the temperature at which re crystallization begins. On the contrary, carbon has a negligible effect on primary re crystallization temperature, when compared with the known effect of substitutional impurities. This is in agreement with the high mobility of interstitials. In effect, only a slight decrease, -20 pct, of the grain-boundary motion rate was noted, due to the interaction between the grain boundary and the carbon atoms. On the other hand, in the samples in which the carbon content is above the solubility limit at the temperature at which re crystallization occurs, a slight increase of nucleation frequency is noted due to the presence of precipitated carbides. ThE effect of purity on recovery and recrystalli-zation phenomena has been known for a long time; however, recently, new attention has been given to the problem since new methods for obtaining metals with extremely low impurity contents have become available. Most of this research work essentially concerns the effects of impurities which cause precipitates or give rise to substitutional solid solutions. The works of Bolling and winegard1 and Aust and utter&apos; on lead, and Vandermeer and orddon&apos; on aluminum, 01sen4 on nickel, and Abrahamson and Blakeney on iron should in particular be referred to. On the effect of this type of impurities a quantitative theory has been formulated by Detert and Lucke6 and has lately been discussed critically by Cahn7 and Gordon and vandermeer.&apos; Interstitial solid solutions in iron have not as yet been studied. As the study of the effect of interstitials is of great interest both from a theoretical and practical standpoint, it was deemed useful to examine the effects of carbon, nitrogen, and boron on recovery and primary recrystallization of iron. There already is some work by Chaudron et al.,1-" on the effect of interstitials on iron; their work, however, mainly concerns secondary recrystallization. The present paper refers in particular to the effect of carbon. EXPERIMENTAL PART Preparation of Materials. The pure iron used for this research was obtained from FeCIS recrystal-lized and purified by extraction with isopropylic ether. From the ferric chloride purified in this manner, hydroxide was precipitated with a solution of very pure ammonia, and, by calcination in pure sintered alumina crucibles, oxide was obtained. Reduction of the oxide to iron sponge was performed in sintered alumina tubes with very pure hydrogen at 650°C; at the end of the operation temperature was increased to 900°C. Specimens for the experiments were obtained by sintering the sponge at 1480°C in pure Hz after a pre sinter ing treatment at 900° C. It is important to note that the treatment at 1480°C in Ha produces a further purification from more volatile elements such as zinc, cadmium, arsenic, lead, and tin. Details on the preparation and characteristics of this type of very pure iron are given in a previous work.&apos;&apos; Only the complete analysis performed by neutron-activation methodsz3 is given here, Table I. Some of the specimens prepared in this way were carburized in the 0 region with very low amounts of carbon by treating them at 700°C in a static atmosphere of Ha containing a definite amount of CO. The set-up used is described in Fig. 1. A gas-tight quartz tube containing the specimen to be carburized and an internal friction control specimen, after being evacuated, was filled with Hz

Jan 1, 1963

By G. Venturello, C. Antonione, G. Della Gatta

Results from work on the effect of inferstitials on recovery and recrystallization of&apos; very pure iron (99.995 pet) doped with nilrogen up to 400 ppm are reported. Nitrided specimens were obtained by heating the iron in a static atmosphere of NH3 + H2. The samples were cold-rolled 80 pet, subjected to a series of isochronal and isothermal anneals, and submitted to examination by X-rays, micrographs, and hardness tests. Small additions of nitrogen show a strong effect in reducing recovery of&apos; the mechanical properties of high-purity iron. At the temperatures of. the experiments, this effect proved greater than in the case of carbon. At 400°C pure iron recovers more than 50 pet of the total hardness increase, carburized iron vecovers 25 pet, and nitrided iron only 10 pet. On the other hand. the addition of nitrogen has, similarly to carbon, a very small effect on recrystallization; the effect is, however, slightly higher than that of carbon. When the concentration Of nitrogen is above the solubility limit in a iron at the temperattue of the experiments, an increase in the frequency of nu -cleation is also observed. THE object of the present work is to improve knowledge on the effect of interstitials both on recovery and on primary recrystallization of pure iron. In fact. at present there are no available data on the effect of nitrogen on high-purity iron. The only work which at present can be somewhat related to this problem is a work of Leak et al.1 in which grain boundary internal friction at high temperature in the presence of increasing amounts of nitrogen is studied by a torsion pendulum. The present work is a continuation of a previous one2 on the effects of carbon. EXPERIMENTAL PART Preparation of the Material. Pure iron was prepared following the same methods used in the pre- vious work2 and was nitrided using controlled quantities of ammonia in an apparatus similar to that used for carburizing. The apparatus consists essentially of a gas-tight quartz tube containing the specimens. The tube, maintained at constant pressure by means of a mercury seal, is placed in a resistance furnace. For nitriding, the NH3 + H2 atmosphere with a suitable concentration of NH3 was introduced into the tube, which had been previously carefully evacuated and degassed by heating at 600°C. The hydrogen used was carefully purified by passing it through a palladium filter. The ammonia required was prepared with the following reaction: CaO + 2NH4CI —CaCl2 + H2O + 2NH3 by heating the mixture of CaO and NH4C1 in a glass flask and then collecting the ammonia in a graduated Hempel burette. For each nitriding program a given amount of NH3 prepared by this method was introduced together with the H2 into the tube previously evacuated. Nitriding of the sample was then performed at 570°C for 48 hr. After this, to ensure a homogeneous distribution of nitrogen, the samples were further heated for 72 hr at 800°C. With this method which uses a static nitriding atmosphere, carefully controlled conditions of purity are obtained. Contrarily, with the conventional continuous-flow methods, using large quantities of circulating gas, there is a greater risk of introducing impurities into the samples. Furthermore, the required nitrogen concentration in the specimen is easily predetermined and obtained. A plot of the relation observed between the initial concentration of NH3 in the gas and the quantity of nitrogen introduced into the iron samples is given in Fig. 1. The data refer to samples of 1.2-mm thickness and to the nitriding conditions previously described. Furthermore, as a comparison, the data relative to two 0.5-mm-thick samples are reported. The presence of a reservoir in the cold zone of the reaction bulb made possible the gradual dissociation of ammonia on the sample in the hot zone. Internal-friction methods were used to determine the content of nitrogen dissolved in the iron samples. Some analyses were also carried out with chemical methods. The following table, Table I, shows a comparison of data obtained with chemical and internal-friction methods. The correspondence between chemical methods and internal-friction

Jan 1, 1964