Search Documents

The exposed high face of Kerr's Quarry has dominated the township of Ferntree Gully for half a century. The near perpendicular face of bare dacite rock is a crumbling scar in an area of significant natural beauty. Apart from being unsightly, the face is a hazard for any person who approaches too close to its base or to the top edge. The height and the precipitous nature of this man made wall of rock is hazardous indeed. (fig. 1) The rock face is on the municipal boundary between the Shire of Sherbrooke and the City of Knox. This boundary was drawn when partition of the Shire of Ferntree Gully took place. There are many advantages in benching back the wall of the quarry but to do so the operation, located in Knox would need to extend into Sherbrooke. There are planning difficulties involved in such a manoeuvre, but during 1972, at a meeting of Cabinet Ministers, it was agreed that the matter be resolved.

Jan 1, 1976

The high cost of sampling systems is largely due to the fact that indiv- idual mechanical type sampling units must be installed at the discharge end of ore/pulp pipelines, that is, at points where the pipeline discharges into pump sumps or the like. A considerable economic advantage may be obtained in the use of a samp- ling device that can be installed at any point in the path of the trans- porting pipe line. Initial tests on a vertical line with an injection sampler using iron ore concentrates reveal the validity of this type sample versus that taken with a mechanical sampler. A descrip- tion of the injection sampler shows its simplicity of installation, requir- ing minimum downtime on existing lines.

Jan 1, 1976

North Stradbroke Island is a large sand mass offshore from south east Queensland. Dredging for mineral sands commenced there in 1956 and the rehabilitation discussed in this paper was commenced in 1967. The frontal dunes have a long history of instability, with little vegetation prior to mining. Re-establishment of the naturally stable contours is essential, and their rehab- ilitation is described. Vegetated high dunes present different problems requiring attention to regeneration of the native species. Methods developed over the past eight years are proving successful.,

Jan 1, 1976

By Ellson I. G

Shay Gap was created for the sincrular purpose of housing, in comfort, the workforce that would be required to mine iron ore, from leases held by Goldsworthy Mining Limited, in hill country, approximately 170 kilometres east of Port Hedland in the Pilbara region of Western Australia. To combat the and environment, the Company ultimately decided to adopt a novel planning concept for the town, which had not been attempted before in Western Australia. The special problems encountered during planning, and the reservations that were expressed during construction and early settle ment, are now part of the dim past. During the three years of occupation now achieved, there has been accumulated a story of success in the provision of an acceptable alternative to modern suburbia. Not only may this be claimed, but it can also be argued that the Shay Gap concept has been a more successful solution to a real environmental problem in our arid Pilbara region than has been seen in other similar settlements.

Jan 1, 1976

Interest in the sampling of refined copper cathodes has heightened over the last ten years. This has followed the increasing importance of cathodes as the principle trading form for metallic copper. It has also been given impetus by recent trends for quality certification of manufacturing inputs, specifically the AS3900 and IS09000 series of standards.

Jan 1, 1976

Sampling is an integral part of gold bullion analysis. Gold mining industries sell millions of dollars worth of gold on the basis of analyses. Biased sampling can cause a serious loss in terms of monetary value to a mining company; hence accurate sampling is of great importance. The sampling procedures for gold bullion will be described. Emphasis is given to the most reliable method of obtaining a representative sample from a gold bar. The problems associated with sample preparation will also be discussed.The sampling procedure at the Kalgoorlie Metallurgical Laboratory will be evaluated in the light of comparative results from the Australian Gold Refineries (Perth, Kalgoorlie). The most common sampling practices adopted by different gold mining companies in the Goldfields and Australian Gold Refineries, Western Australia will also be presented.

Jan 1, 1976

Preparing for automated sample preparation has two facets; the need for better procedures as seen by the laboratory Manager and the approach to be adopted as envisaged by the equipment manufacturer. Both have many options and during the 1990s some at least of these options will be tried. As automation of sample preparation is only just beginning, can it be said that there is a real need for better procedures. What does automated sample preparation have to offer? Does it have real advantages or is it just a marketing tool to sell equipment?

Jan 1, 1976

Working thick coal seams in Poland is a very serious problem. Nearly 40 per cent of all coal is extracted from seams more than 3 m. thick. In absolute figures this represents about 70 million tons of coal per year. Working seams with thicknesses up to 3.5 m. does not present, at present, major difficul- ties. Working thicker seams calls for a steady improvement in order to increase the degree of utilization of the deposit and to enlarge the concentration of output. The problem is sometimes more difficult because, in many cases, the seams are worked under protected surface structures which compels the mines to use hydraulic stowing with all its advantages and disadvantages. Rock burst hazard, the control of which is the basic problem hindering the mining, is a further problem. The mining systems used in Poland are adapted to these natural and technical conditions.

Jan 1, 1976

As Coal Mining Areas develop, problems relating to strata control increase. The "easy" coal has been extracted and the future development lies in the direction of greater depths of cover and more difficult strata conditions. To provide solutions to the problems encountered the techniques of constructing and testing physical models have been developed and refined. With a sound knowledge of model theory allied to practical experience, mining research engineers use physical cemented material models to examine, assess and solve mining problems relateu to strata behaviour and environment. For a model to provide the answer to a particular mining problem it is essential that as much information as possible be obtained from the mine or area of a mine which the model is to represent. Details relating to the strata, geological malformations, and the stress environment must be collected and collated to ensure reliable results.

Jan 1, 1976

An approximate rapid design system for tunnel liners and underground structures is presented which permits the effects of structure geometry and stiffness, rock quality in terms of its deformation modulus, and the applied system loading to be entered as data to produce direct designs conforming to stress limitations, optimum reinforcement requirements and restraints on section dimensions. An 'equivalent column' concept is introduced for modelling the rock mass in contact with the structure. Only the rock treatment is given in detail but the results of sensitivity analyses, with reference to rock quality, for a typical liner design are given and these results related to a number of empirical design approaches.

Jan 1, 1976

By P M. Outhwaite

Everyone present today is especially aware of the need for minerals in this society of ours. The words 'especially aware' were deliberately chosen because this is a meeting of the NZ Branch of The Australasian Institute of Mining and Metallurgy not a dilettante group such as some of our critics. Members of the Australasian Institute of Mining and Metallurgy knew that our great farming industry, our shelter, our transport and our energy supply, are largely dependent on a flow of minerals into this country despite the presence of large coal and natural gas reserves. Flow in was said because New Zealand imports most of its mineral requirements with all the consequential strategic and economic disadvantages. If the above statements are accepted by this gathering it would be a premise fairly stated that New Zealand has a great need to discover and develop minerals.

Jan 1, 1976

The recommendations of a recent American report on "Better contracting for Underground Construction" are considered in relation to Contracting practices on major Australian projects by representatives Of the "classical trilogy" - the Owner, Engineer and Contractor.

Jan 1, 1976

Oxidation or sulphidization of the surface of pyrrhotIte partIcles enhances atomic interdiffusion at elevated temperatures and provides a mechanism for interface growth between particles in contact. In a mass of pyrrhotite-rich ore or tailing, where oxidation heating is not controlled, bonding of particles by diffusional mass transport contributes significantly to the agglomeration of the mass.

Jan 1, 1976

By Roden S

This paper illustrates that sampling problems and difficulties are as common in an R&D environment as they are in an operating plant. Researchers need to be aware of the potential influence of poor sampling practices and when feasible determine the sampling and analytical precision at the start of any experimentation. Specific problems that have been encountered are discussed and the procedures implemented to overcome these difficulties are described. Examples from projects include the cyanidation of a Au/Ag ore, column leaching of refractory gold and oxide ores, the bioremediation of contaminated sites and the flotation of ore containing native copper.

Jan 1, 1976

This paper describes an investigation of the sampling problems which contributed to erroneous Concentrator production forecasts at the mining operation of Bougainville Copper Ltd (BCL) in the North Solomons province of Papua/New Guinea.Reference figures provided by independently verified commercial shipment data demonstrated the existence of a bias in the calculated Concentrator production; the challenge was to identify systematic errors in each of the contributory measurements (feed tonnage and feed, tailings and concentrate grades).The uncertainty surrounding specific sampling and measurement errors precluded optimum metallurgical control and performance of the milling circuit, encouraged disputes about the difference between Mine versus Concentrator production estimates, and cast some doubt on efforts to follow political guidelines concerning a maximum feed tonnage or recovery oriented mill operating concept.An evaluation of routine results as well as specifically targeted test work identified the sampling errors associated with measured individual parameters.The emphasis in this report is on the procedure for quantitative error assessments.The measured performance of a mineral dressing plant is subject to a systematic error balance which can be derived from the more familiar weight and metal balances such as the two- or three-product formula.The resulting equations are generally valid, and they are applied to the measurements obtained at BCL's Concentrator to illustrate the method.

Jan 1, 1976

Severe development difficulties were experienced soon after in-seam mining commenced at Appin Colliery in'1962. Thirteen years later no significant pro- gress had been made in overcoming some aspects of this development problem. Some success had been achieved in destressing roadways both in development and pillar extraction. Longwall retreat mining had shown promise of being highly productive but at an extremely high cost in terms of development requirements both in number of roadways and intensity of support in those roadways. No real advance was made in the problem of driving the first heading of a group of headings under conditions of apparently high stress in directions other than the preferred mining directions, although failure of the roof in this heading did seem to give easier work in the subsequent headings driven particularly if they were driven on narrow centres.

Jan 1, 1976

The 5.6 km Canning Tunnel was constructed to improve water supply from Canning Dam to the Perth metropolitan area. The site area is in the Darling Range which is essentially a laterite-capped plateau-remnant underlain by Archaean granitic rocks, intruded by dolerite. Two arrangements were available. After geotechnical investigations which included geological mapping, seismic refraction geo- physics, diamond drilling and mechanical rock testing, a single tunnel was selected in pre- ference to two short tunnels and a connecting pipeline. The tunnel is hydraulically equivalent to a fully lined tunnel 1.83 m in diameter and 5 580 m long. The alignment diverged from a straight line so that the initial upstream section was almost normal to the contours which allowed for minimal support requirements in a weathered zone. Although steel and con- crete lining was needed at both ends, the main section of the tunnel was unlined except for a concrete floor. A sand and rock trap with a capacity of 46 m3 was constructed near the outlet portal to collect debris and sand down to a size of about 2 mm. Portal excavations were in highly to completely weathered rock which extended 56 m into the tunnel at the upstream end, and 18 m at the downstream end. Conventional drilling and blasting were used for tunnel excavation with survey control by laser. Breakage lEngineering Geologist, Mines Department, Perth, W.A.

Jan 1, 1976

The methods and equipment developed and used at the Mount Isa mine to obtain samples of uncemented hydraulic fill lying above major horizontal pillars are described. From existing underground development, samples were obtained at distances up to 50 m, of which up to 30 m was through hard rock. Samples were used to predict fill behaviour as it affected mining security during recovery of the pillars.Specialized equipment for difficult sampling situations and also other sampling exercises are described.

Jan 1, 1976

By Brown D. N, Troth D. A

Large blast furnaces demand high standards of preparation of feed materials which must meet tight specifications of chemical and physical quality. Measurement of these factors must be expeditious but the nature of the coke, sinter, ores and fluxes and the large tonnages involved requires substantial mechanical sampling plant. The equipment, its operations, and its problems, associated with the 5000 t.p.d. No.5 blast furnace at Australian Iron and Steel Pty. Ltd., Port Kembla, are described and the efficacy of chemical blending achieved in the ore blending yards and sintering operation, is reported.

Jan 1, 1976

The discovery of economic uranium miner alisation in unique geological conditions at Yeelirrie, 700 km NNE of Perth, presented Western Mining Corporation Limited with a num- ber of sampling and evaluation problems. Carn- otite mineralisation occurred in a porous cal- crete-clay lithology in close proximity to the water table; background information on such a deposit was non-existent and sampling in these conditions could be difficult. The deposit was sampled initially by aug- er drilling with X-ray fluorescence analysis of drill cuttings, followed by reverse circulation and diamond drilling with analyses by X-ray fluorescence and gamma logging of the holes. Two costeans provided lithological and grade distribution data and mining experience in the deposit. Spoil from the costeans was stockpiled according to location in the first costean and according to location and grade in the second costean. Samples from the various stockpiles were analysed by X-ray fluorescence. No. 1 costean was extensively sampled by channel sampling of the walls and by pit sampling of the floor of the benches of the costean by back hoe. No. 2 costean was sampled by Geiger counters mounted in T-probes and by the gamma logging of auger holes to establish the valid- ity of the T-probe results. Samples were taken

Jan 1, 1976