Search Documents

By Maarten van de Vijfeijken, Marco Rufli

"By using the latest generation of medium voltage frequency converters, new possibilities have arisen to improve the grinding process. Beside all the direct and indirect advantages, several dedicated functions have now been implemented for ring geared grinding mills in the minerals industry. The advanced operational functions ensure a smooth, safe and reliable operation with minimum stress for the mechanical equipment and therefore highest availability of the mill. Several papers have already been presented concerning the benefits of using this state of the art technology for mill drives (Ravani von Ow and Bomvisinho, 2010; Ravani von Ow and Gerhard, 2010). However this paper will not only show and explain the operational benefit of these functions, but will focus on the experiences gained with this kind of sophisticated ring geared mill drive system. Several measurements of different operating conditions (starting, frozen charge remover, controlled roll back, backlash, etc.) made on an installed and commissioned 2 x 5 MW dual pinion ring geared mill drive system will be shown and discussed. Also the accuracy of the load sharing between the two 5 MW motors during starting, normal operation and stopping will be demonstrated using real measurements from an operating system. Finally the inherent features of these drive systems are briefly discussed.INTRODUCTIONLooking at the demands of grinding mills, we can split them into operational, maintenance and protective demands. For smooth and safe operation, it is important that critical situations are avoided as much as possible. Maintenance functionality must be quick and easy to execute, while protection of the system is important during all operating conditions. ABB has considered all these demands during development of their dedicated mill functions. By adding an additional controller (mill controller), not only a lot of application related functionality and protection is included, but also the interface between the mill drive system and the customer’s distributed control system (DCS) is simplified."

Jan 1, 2011

By D. Haraguchi, S. Izawa, C. Tokoro, S. Owada

"Arsenic is widely known as a toxic element for humans, animals and plants. Because of more stringent wastewater standards not only in Japan but also around the world, research for appropriate and efficient treatment method for arsenic is becoming increasingly important. Coprecipitation or adsorption process using ferrihydrite is widely implemented for dilute As(V) removal from wastewater. In this study, the sorption mechanism of dilute As(V) with ferrihydrite in coprecipitation or adsorption process was investigated. To accomplish this, we conducted batch experiments of coprecipitation or adsorption and compared these results for sorption isotherm and zeta potential. These experimental results showed that sorption mechanism in coprecipitation process depends on the initial As/Fe molar ratio; simple twodimensional adsorption onto the surface of ferrihydrite when the initial As/Fe molar ratio was < 0.4, and some three-dimensional uptake with ferrihydrite when it was = 0.4. We also evaluated the sorption mechanim by analysis of X-ray diffraction (XRD) and X-ray Absorption Fine Structure (XAFS). XRD or XAFS spectra showed that surface precipitation of amorphous ferric arsenate was formed when the initial as/Fe molar ratio was = 0.4, beyond the thermodynamic bulk precipitation range for ferric arsenate.INTRODUCTIONArsenic is toxic to animals, including humans, and long-term exposure to arsenic via drinkingwater causes cancer of the skin, lungs, urinary bladder, and kidneys, as well as other effects on the skin such as changes in pigmentation and thickening (Ghosha et al., 2008). Elevated levels of arsenic are often present in the environment as a result of the weathering and dissolution of minerals as well as in response to numerous anthropogenic sources including the discharge of mine wastes, coal fly ash and the use of pesticides that contain arsenic (Nriagu, 1994; Singh et al., 2007). Indeed, the potential for arsenic exposure affects many people, as evidenced by several million people in Bangladesh and India being at risk of exposure via drinking water obtained from contaminated groundwater sources (Ahmed, 2001).Acid mine drainage (AMD) containing arsenic is a global environmental problem (Dold, 2008; Liang and Thomson, 2008) that also affects Japan, which has many abandoned or closed mines that have been generating AMD for the last few decades (Masuda et al., 2008). Several such facilities in Japan produce AMD containing dilute concentrations of arsenic that exceed Japanese effluent standards (0.1 mg/dm3) (METI, 2006). For example, AMD from the abandoned Horobetsu sulfur mine, the largest AMD source in Japan, contains approximately 10 mg/dm3 arsenic."

Jan 1, 2012

By H. Sipilä, H. Vartiainen, H. Paarma

"The carbonatite massif of Sokli includes several low-grade Nb showings composed of ores and wastes as identified by routine analyses. More detailed lithologic proportions were determined in two orebodies in the Kaulusrova Nb-mineralized area by a careful geological study and by thorium radiation measurement on 10 cm-long drill core cuttings with a total length of 460 metres. The distribution of Nb in eight X-ray spectrometrically analyzed drill core sample intervals (totalling 35.8 m) was determined by analyzing the intervals semi-continuously by an X -MET analyzer. The geological studies suggest that Nb-mineralized bodies are feasible fo r the sorting of are and waste. This was confirmed by the semi-continuous determination of Nb on the X-MET analyzer.IntroductionThe Sokli carbonatite complex is located in eastern Finnish Lapland. The main ore of the carbonatite massif is a regolithic phosphorus ore in the weathered crust. Large-scale geophysical measurements and diamond drillings have also established several niobium showings within the magmatic carbonatites. Owing to the complicated geology of the massif, the niobium showings occur as irregular zones o r areas displaying complicated structure, texture, mineralogy and geochemistry (Vartiainen and Paarma , 1979; Vartiainen , 1980). The tonnages in areas such as this are large but the grades in-situ are low . The most intensely studied niobium showing is the Kaulusrova area.The exploitation of these showings depends on the feasibility of applying a sorting technique to upgrade the feed and to minimize the amount of material to be treated in the concentration plant. These possibilities o n the Kaulusrova area have been viewed by a detailed geological and X-MET an analyzing study."

Jan 1, 1985

"RÉSUMÉOn discute les principales sources de dilution au cours d’une exploitation souterraine. Les différentes définitions de la dilution en usage sont analysées. Une nouvelle méthodologie de calcul simplifiée et facile à utiliser dans la pratique minière est présentée. Cette méthodologie permet de remplacer les différentes expressions analytiques en usage par les deux facteurs de dilution seulement : un «facteur de dilution planifiée» lié à la sélectivité d’abattage au niveau de la planification minière et un «facteur de dilution additionnelle » permettant de juger de l’efficacité du contrôle de terrain et de la dilution pendant l’exploitation souterraine. L’application de cette méthodologie donnerait un outil nécessaire aux niveaux de la planification, du suivi des travaux d’exploitation et d’éventuelles études comparatives des coûts entre les différentes situations minières.ABSTRACTThe principal sources of dilution during underground evaluation and mining are discussed, then definitions of ore dilution currently in use are analyzed. These definitions vary depending on the authors. A new ore dilution evaluation methodology is proposed, replacing the ten different analytical expressions by only two: the planned dilution factor related to the stoping selectivity, done at the mine planning level, and the additional dilution factor related to the efficiency of the dilution control measures during stoping operations. The conclusion shows that the use of this methodology would be a definitive asset in planning, in stoping operations follow-up, and in future costs comparison studies between mining operations."

Jan 1, 2001

By M. F. Goudge

MAGNESIA refractories and magnesium metal are both essential war commodities. The need for magnesium, which had just made its debut as a commercial metal a few years before the outbreak of the present war, is widely known because this new and valuable light metal has already received much publicity. Less widely known but equally important in the war effort are magnesia refractories. They are indispensable to the efficient functioning of the great metallurgical plants producing steel, nickel, copper, and other metals, where, because of their resistance to extreme high temperature and chemical attack, they are used in lining the furnaces, which are operated at a white heat. The demand for refractories in the metallurgical industries rose rapidly upon the outbreak of war, and now, in consequence of the continued great expansion under way in the manufacture of steel, nickel, copper, and other metals, the need for magnesia is greater than ever. Since 1915, part of the Canadian requirements of basic refractories has been supplied from the deposits of magnesitic dolomite in Argenteuil county, Quebec. The products from these deposits are excellent for many uses, but the magnesitic dolomite has too high a content of silica and lime to be used in making a type of magnesia brick required in nickel converters, and in the roofs of reverberatory furnaces used in the copper and steel industries. There is now a large and growing demand in Canada for bricks and shapes for these uses. This demand has always been supplied from the United States. Makers of these products in the United States, in turn, formerly imported most of the necessary high-grade, dead-burned magnesia from Austria and Manchuria. Not only are these sources closed, but refractory chrome ore from the Philippines is no longer available and chrome refractories may have to be in large part replaced by magnesia.

Jan 1, 1942

By T. H. Janes

"IntroductionSULPHUR is a constituent of many industrial products. It is part •of almost anything we eat, wear, or use. In fact, sulphur is so important that there has been an increasing tendency in recent years to measure industrial growth in terms of sulphur consumption.The uncertainty of obtaining adequate supplies •of elemental sulphur from the Frasch-mined domes. of Texas and Louisiana in the United States led all countries in 1950 to seek alternative sources of supply of this necessary element.Canadian industry has been supplied, for many years, with most of its sulphur requirements by United States Frasch-mined sulphur. World demand for this sulphur has necessitated the imposition of controls on its distribution, as production has not kept pace with demand. Until the third quarter of 1950, Canadian manufacturers of pulp and paper, heavy chemicals, explosives, and textiles •experienced little difficulty in obtaining their needs of elemental sulphur from the United States. However, at that time, low producers' stocks and declining reserves threatened to reduce shipments from producers, with the prospect of a continuing shortage for some time. These conditions, together with higher prices, stimulated the search for alternative sources of supply in Canada."

Jan 1, 1952

By Richard Lavallée

La Mine Louvicourt est une mine hautement mécanisée exploitant un gisement polymétallique avec des chantiers transversaux minés et remblayés selon une séquence primaire-secondaire. Dans certaines parties du gisement, il n&apos;y avait qu&apos;un accès à la coupe inférieure, car il n&apos;était pas rentable d&apos;avoir aussi un accès par coupe supérieure. Le minerai situé au-dessus des chantiers avec trous ascendants était considéré comme ressource non rentable par minage mécanisé. L&apos;option de miner ces ressources avec des sous-niveaux avec accès par monterie alimak et forage long-trous de petit diamètre fût donc étudiée et démontra une rentabilité intéressante, particulièrement en considérant les tonnes ainsi minées comme tonnage supplémentaire au tonnage planifié. Dans ces chantiers, les détonateurs électroniques ont été très utiles et de plus, les coûts d&apos;explosifs ont étés réduits considérablement par l&apos;utilisation d&apos;émulsion pompée en vrac.

Oct 1, 2004

By A. M. Girodo

"Dorbyl Heavy Engineering has been manufacturing winders since 1949 mostly for the South African mining industry.Table 1 shows that the vast majority of winders have been double drum winders. At the greater depths with larger ropes being employed, it became apparent that multi-rope winders would be needed. The high stress variation in Koepe winder ropes at great depths especially beyond 2000 m, ruled out this possibility. Thus the original concept was borne for the Blair multi-rope winder where the stress level variations in the rope would be as per the well known, tried and tested double drum winder. The Blair multi-rope was also devised to increase payload by using multiple ropes.With the increasing costs of transporting men and material coupled with fact that orebodies are getting deeper, various feasibility studies have been carried out by South African mining houses. For this reason Dorbyl Heavy Engineering has done conceptual design work of both double drum and Blair multi-rope winders with diameters up to 8.5 m dia (still well within our manufacturing capabilities). These feasibility studies have looked at depths approaching 4000 m*.This paper covers the typical duties leading to the choice of single drum, double drum, Koepe and Blair multi-rope hoists on South African gold mines. A brief synopsis of Dorbyl hoists in use in the South African mining industry, with some indications of future trends, will be discussed.With current installed depths of wind approaching 2500 m, the Blair multi-rope hoist has been used extensively for the heavier payloads.Some of the main considerations pertinent to the design of the Blair multi-rope hoist are illustrated together with the implications of using this type of hoist to winding depths of3000 m to 4000 m in the foreseeable future."

Jan 1, 1995

By Malcolm Powell

"The argument has long raged across the oceans as to what the best AG/SAG mill aspect ratio is. The North American practice of a high aspect ratio of two, diameter twice length, through to the South African and Scandinavian practice of an aspect ratio of as low as a 0.5. Within the collaborative P9 AMIRA project the MPRU of the University of Cape Town and the JKMRC of the University of Queensland have been collecting plant data pertinent to this issue over the past four years.The JK SAG mill model developed by the JKMRC is based upon data collected from mills having a range of aspect ratios from 1 up to 2. The maximum mill speed, mill load, and ball filling in the fitted data base were all below the operating range common in South Afr-ica. The extension of the P9 project into South Africa therefore lent an ideal opportunity to collect data in a whole new window of operation that would allow the range of applicability of the semi-empirical SAG model to be greatly extended.At the heart of the differences in aspect ratio is the completely different operating practice for high- and low- aspect mills. The mill filling, mill speed, and recirculating loads of closed-circuit single-stage operation have more influence on the differences in operation than the pure aspect ratio relationship. Relationships for load have been extended to 45% filling, with the modified model showing the measured peak in throughput as the mill filling increases. The ball load relationship now covers fillings of over 30% balls (of total mill volume), thus including so-called SAG-ball mills. The influence of closed circuit operation has been measured. It has been found that a key issue of the high slurry flows associated with closed circuit operation, especially when closed with a cyclone, is the pulp discharge limitation of the traditional grate and radial lifter configuration. It has also been observed that absolute mill length is more of an issue than aspect ratio. Slurry flow along the mill and charge segregation within the load are being investigated on pilot and full-scale mills to provide data for potentially modifylng the perfect mixing model that is used for the SAG mill.Improved understanding of these aspects of SAG mill operation and extension of the JK SAG model to better cover the entire range is allowing serious direct comparison of high- and low aspect mills for the first time. It is the conclusion of the researchers working in this area that there is no one best practice, that in fact mills across the range have their application based on ore type, desired product, available capital and on operating costs. Developing robust designs allows direct comparison of two-stage circuits using high-aspect primary SAG mills, with single-stage closed circuit low-aspect SAG mills. The new operations within South Africa are now considering both circuit types, and data is presented on selections that cover the full range of aspect ratio and operating practice."

Jan 1, 2002

By J. P. Caulfield

THE Hudson Bay Mining and Smelting Company&apos;s underground mine at Flin Flon, Manitoba, has in the past been serviced by two working shafts-the North Main shaft, and the No. 3 shaft. The North Main shaft is used to hoist the total production from under-ground, and handles the greater part of the mine supplies and crews. The shaft is five-compartment design, rectangular in cross-section, and is equipped entirely with steel shaft sets from the surface to the finished depth of 2,210 feet. Hoisting equipment in the surface plant will not permit the North Main shaft to be extended below its present finished depth. The No. 3 shaft, located approximately 2,300 feet from the North Main shaft, is used primarily as a ventilation shaft, and for hoisting lower-level development waste to the 390 level, where this material is used as mine fill. The No. 3 shaft is of standard rectangular design, timbered with 8-in. by 8-in. creosoted fir sets, hung on 6-foot centres. From the surface to the 1,430 level, the No. 3 shaft consists of three 5 ft. by 5 ft. compartments, and below this level to the completed depth of 2,300 feet, the shaft is increased to four compartments. To service the mine and to expedite development below the 2,210 level, a one and one-half compartment winze was sunk from the 2,210 level to a depth of 766 feet, or approxima tel y the 3,000 level.

Jan 1, 1941

By Bob Robinson

In 1990, the European Space Agency (ESA) initiated a technology transfer program to stimulate the wider use of technology developed by the European and Canadian space communities. This paper focuses on the method of technology transfer from the space industry to terrestrial industries, with a focus on the mining resource sector within a program called the Harsh Environments Initiative (HEI) created in 1997. Other resource sector applications include forestry and oil & gas. C-CORE in partnership with the Mining Innovation, Rehabilitation and Applied Research Corporation (MIRARCO) supported by ESA, Canadian Space Agency (CSA) and European R&D organizations conduct projects to promote and demonstrate the transfer of innovative technologies from space to non-space industries. Space programs have and continue to develop new knowledge for extra-terrestrial application, e.g., satellite earth observation, manned missions and unmanned planetary exploration. Many of which hold the potential for application on land and ocean. Currently, space technologies of interest to the mine sector range from robotics and image analysis to sensors, software and advanced materials. The HEI works to identify and apply these types of technologies in the areas of automated/tele-controlled mine operations and mine monitoring.

May 1, 2001

By K. J. Palmer, D. A. Silva

"Evaluating resources and reserves requires the reliable modelling of geological domains and their grades. “Multiple point statistics” simulation is a relatively new geostatistical method to generate complex, high-resolution geological models by extracting high-order spatial relations from training images. A method based on combining multiple training images is developed to obtain the correct amount of large-scale continuity and short-scale variability. A calibration process matches the geological spatial variability between the final realizations and the drillhole dataset. A case study with data from the Red Dog mine, Alaska, United States, shows an appropriate reproduction of short-scale variability along boundaries between geological units.RÉSUMÉ L’évaluation des ressources et des réserves exige une modélisation fiable des domaines géologiques et de leur teneur. La simulation par « statistique multipoint » est une méthode géostatistique relativement nouvelle pour générer des modèles géologiques complexes à haute résolution par l’extraction de relations spatiales d’ordre supérieur à partir d’images d’entraînement. Une méthode basée sur la combinaison de multiples images d’entraînement est développée afin d’obtenir la bonne quantité de continuité à grande échelle et de variabilité à petite échelle. Un processus d’étalonnage fait correspondre la variabilité géologique spatiale entre les réalisations finales et l’ensemble des données de forage. Une étude de cas avec des données de la mine Red Dog, Alaska, États-Unis, montre une reproduction adéquate de la variabilité à petite échelle le long des limites entre les unités géologiques."

Jan 1, 2015

By Jan Rosenkranz, Anders Sand, Lisa Malm, Nils-Johan Bolin

Within flotation technology the general trend is towards very large cells. Scale-up is usually done by postulating geometrical similarity, which implies keeping the aspect ratio constant when increasing cell volume. Consequently, the design of flotation circuits typically involves several cells of identical geometry within a bank. Using a few standard sizes in a flotation plant simplifies design, manufacturing and maintenance of the cells, but does not necessarily guarantee optimal performance and selectivity of the flotation process. Geometry parameters for a given cell volume that influence flotation cell performance include cell height, which causes changes in the hydrostatic pressure and suspension hydrodynamics, and also influences the travel distance of particle-bubble agglomerates as well as the homogeneity of the mixing. Also the thickness of the froth layer depends on the aspect ratio of the cell. The objective of this work is to gain a better understanding of material distribution and properties within a flotation cell and, based on this information, elucidate how alterations of the cell geometry can influence separation efficiency. For this purpose systematic measurements and analyses of the spatial distribution of the different phases within a 160 m3 flotation cell have been carried out with a particular focus on an industrial, low-grade copper ore beneficiation process. The concepts for sampling at different vertical and lateral positions of the flotation cell are introduced. The results from the experimental work give an understanding of internal material distribution within flotation cells. Based on the measured phase distribution and concentrations as well as particle properties at various positions within the cell, the implications for an optimized scaling and design of individual flotation cells within a flotation circuit are discussed.

Jan 1, 2016

By A. Y. Senchenko, Y. V. Kulikov

"In recent decades HPGR technology has proven itself in comminution circuits of mining plants. High technical and economic performance, lower specific energy consumption and reliability of HPGR equipment makes it an efficient alternative to conventional circuits using stage crushing and rod/ball milling, as well as to AG/SAG circuits. However, despite all the advantages of this technology the correct selection of key and auxiliary equipment is very important since errors at testing and design stages may lead to discrediting of the whole concept of HPGR application. There is a great variety of possible circuit configurations using HPGR, e.g. with circulation of edge product, with crushing of the whole discharge and circulation of screen oversize, successive two-stage crushing, etc. Each type of minerals will require its own optimal crushing circuit. In this context the testing methodology for selection of an optimal configuration becomes of prime importance. It is common knowledge that the best simulation of material crushing and softening within a HPGR can be obtained only in the course of a large-scale pilot test. The main approaches applied to this kind of testworks are described in this article. Special aspects of HPGR technology design and industrial operation are revealed as well. Some operational issues of HPGR equipment and of circuit as a whole were detected. They are related to regions specifics, plants location, and other factors. Process solutions proposed to deal with these issues are also indicated in the article. INTRODUCTIONDesign and construction of the processing plants involving High Pressure Grinding Rolls (HPGR) technology becomes more and more common in mining as this technology has specific technical and economic advantages against the circuits with autogenous/semiautogenous mills (AG/SAG) and other circuits. The main advantage of the technology is low energy consumption and low operation costs respectively. The presence of microcracks and increased content of fine size fractions in the crushed product contribute to reduction of energy required for further ball grinding. Besides, HPGR technology applies a special wear resistant liner that enables significant reduction of operation costs of grinding media and liner comparing with AG/SAG circuits."

Jan 1, 2016

Pilot plants for pressure hydrometallurgy represent special design and project execution challenges unique to the industry and to the pilot- and demonstration-scale. Pilot plant projects have different objectives and shorter timescales than commercial plant projects. Design considerations and strategies, and project execution methods that meet the special needs of pilot plant projects, are discussed. Specific guidance is given for the selection of appropriate pressure and temperature design points for pressure hydrometallurgical process equipment, and for the selection of materials of construction for pilot-scale equipment. The balance between the need for process similarity with future commercial operations and the realities of pilot-scale equipment is also discussed.

Jan 1, 2004

"Pilot plants for pressure hydrometallurgy represent special design and project execution challenges. Over the past twenty years, Zeton has designed and fabricated a variety of world-class pressure hydrometallurgical pilot-plant facilities, and this paper discusses design considerations and strategies related to such projects. Project execution methods are also discussed, and guidance is given for the selection of materials of construction and for the selection of appropriate pressure and temperature design points for pressure hydrometallurgical pilot equipment. The paper concludes with a discussion of the need for process similarity with future commercial operations and the realities of pilot-scale equipment.INTRODUCTIONThe process technology developer or owner and the designer/fabricator of a new pilot-plant facility are faced with some difficult technical choices even after the decision to build a dedicated plant has been taken. A pilot-plant project is usually on the critical path of a large commercial project involving investments many multiples greater than the capital cost of the pilot plant. Schedule savings in the design, manufacture, and commissioning of the pilot plant or in a rapid completion of the experimental program can be disproportionately beneficial to the overall development project. However, inappropriate shortcuts resulting in major oversights can be disproportionately problematic.A number of considerations and suggestions for both the project execution approach and the process engineering design of pressure hydrometallurgical pilot-plant facilities are presented as a guide for potential owners and operators of new pilot-plant equipment and facilities."

Jan 1, 2012

By Theo. A. Link

ACCORDING to our office dictionary, geology is "the science that investigates the structure of the earth and its successive physical changes", and a geologist is "one who knows the science of the structure of the earth". No doubt this definition does not suit all of us. Another dictionary would have the definition slightly different. As an example, one dictionary stated that "a geologist is one who practices geology". (Some of our clients told us to quit practising and get to work). There are many different types of geologists engaged in various branches of the profession and some of these are further broken down into subdivisions so that specialization is becoming more and more prevalent. As a result it is, in some cases, doubtful whether or not we are actually dealing with a geologist in the generally accepted sense of the term.

Jan 1, 1956

By C. A. Young, H-H. Huang, L. G. Twidwell

Equilibrium calculational software programs can be effectively utilized to model important parameters in aqueous and aqueous/solid systems, e.g., activity or concentration, solubility, temperature, solution pH, solution potential, and ligand complexation. In this regard, the calculational program ST ABCAL will be demonstrated. Illustrative examples for the creation of diagrams such as potential-pH, and activity or concentration-pH will be presented to demonstrate the fundamentals in real hydrometallurgical systems. Speciation, titration and mixing will be used to simulate or predict operational processes. Berkeley Pit water from a flooded abandoned copper open-pit mine will be used to illustrate the modeling process. According to analytical results the water contains about 20 important constituents. In addition to measured potential and dissolved oxygen, there are two distinctive oxidation/reduction couples. Concentration and other experimental parameters are seldom matched to each other and 12 different conditions have been identified. Water for each condition must be speciated in order to find the best-fit model. The STABCAL program will be used for the modeling calculations and the implication of the water chemistry to defining treatment opportunities will be discussed.

Jan 1, 2005

By Yongteng Dong, John P. Quinn, Bradford Wesstrom, Guikuan Yue

With increasingly low-grade copper ores being mined, it is difficult to handle growing concentrations of As, Sb, Bi and/or Fe in the whole flowsheet, especially during copper electrorefining. To better elucidate the effects of those impurities on the quality of cathode deposit and/or current efficiency, a detailed speciation study of the electrolyte under industrial conditions is required to quantitatively describe their distribution in the solution, thereby facilitating their effective control and removal. In the present study, a thermodynamic model of complicated iron-arsenic-copper-sulfuric acid electrolyte under industrial conditions was developed. The main species of those elements involved in the electrolyte were first identified, and their thermodynamic data were collected and critically assessed. Those data were then used to estimate the activity coefficients of species, and to calculate the equilibrium constants from 25°C to 70°C. The developed model provides a mathematical tool that is capable of quantifying the concentrations of free ions and complexes in terms of temperature and solution composition. Finally, oxidation-reduction potential measurements were employed to validate the model. INTRODUCTION In copper electrorefining, impurities like arsenic, antimony, bismuth and/or iron can partially dissolve in the electrolyte and accumulate gradually, and eventually cause problems such as bad cathode deposit (co-deposition with copper or mechanical inclusion from the floating slime), lower current efficiency, etc., which eventually increases the operating costs. The presence of impurities may substantially reduce properties of copper products such as conductivity, corrosion resistance, mechanical properties, and leads to more energy consumption (Schlesinger et al., 2011; Jafari et al., 2017). To remove these impurities, various methods have already been proposed and applied in industrial copper production, such as solvent extraction, ion exchange, chemical precipitation, absorption by activated carbon, etc. (Cunningham et al., 1997; Navarro et al., 1999; Toyabe et al., 1987). In addition, adding reducing agents such as sulfur dioxide and trivalent arsenic could also precipitate arsenic, antimony and bismuth from copper electrolyte, by changing the distribution of impurities with various valence (Braun et al., 1976; Xiao et al., 2007). The disadvantages of those methods include high energy consumption, serious contamination, lower selectivity and efficiency, and so on.

Jan 1, 2019

By Stephen L. Chryssoulis, Stamen Dimov

"Preg-robbing has been known for many years, where increased losses are suffered because dissolved gold is removed from solution by adsorption onto carbonaceous matter. In direct cyanidation circuits it is reasonable to conclude that the preg-robbed gold is either in a gold cyanide [Au(CN) - 2, AuCN] or metallic [Au°] form. However, in circuits with a pre-oxidation step possibilities increase and multiply even further because of water recycle streams containing apparent and not-so-apparent gold ligands. It is in these circuits where speciation of sorbed gold, i.e. the identification of the gold compound, is useful. The importance arises from the fact that proper identification of the sorbed gold species can be used to determine how, when, where and why gold was removed from solution, thereby identifying the exact cause of the problem and providing clues as to how it may be rectified.INTRODUCTIONTo the best of our knowledge, this is the first attempt ever to speciate gold preg-robbed by carbonaceous matter using a surface sensitive microbeam technique. This approach enables the direct determination of gold species sorbed on carbonaceous particulates, opening an entirely new field in the understanding of the chemistry of gold sorption on carbon. The reasoning behind this effort was to add to the current knowledge of the detrimental effect chloride ions have on gold recovery by the pressure oxidation and in particular why in the ensuing CIL step, gold is not being desorbed from the surface of the carbonaceous particles (Table 1)."

Jan 1, 2004