Search Documents

By Margaret R. Lickes

Mercury was produced originally at the Idaho Almaden mine from 1939 to 1942. When the ;.nine was shut down, more than 100,000 tons of ore, containing from 2.5 to 3 pounds of mercury per ton, was known to be adjacent to old workings but had been considered too low grade for commercial operation. Later, detailed, systematic exploration by Rare Metals Corporation of America increased and delimited enough minable reserves for further operation to be foreseen for several years. The average grade of the ore is estimated at slightly more than 3.5 pounds of mercury per ton. Open-pit mining and installation of the largest rotary kiln in the United States furnacing mercury ore have made possible profitable exploitation of these reserves (fig. 1). The bulk of the exploration was by percussion drilling, although some diamond drilling was done to check the results. When enough reserves were indicated to assure a successful operation, stripping and plant construction were started simultaneously. Figure 2 is a general view of the plant. The ore bodies, although irregular in size, shape, and grade and covered by essentially barren cap rock, are amenable to low-cost, trackless, open-pit mining. Development consists of stripping the overburden and removing, barren cap rock. Ore is being mined at approximately [5],000 tons per month and treated in a 175-ton-per-day furnacing plant.

Jan 1, 1957

By W. L. Dare

This paper is one of a series being prepared by the Bureau of Mines on the methods and costs of mining uranium on the Colorado Plateau. The Continental No. l mine is at the south end of the Big Indian mining district, San Juan County, Utah. The mine is on a school section owned by the State of Utah and leased by Continental Uranium, Inc. A 70,000-ton uranium-vanadium ore deposit was discovered as a result of an exploratory drilling program completed in 1954.

Jan 1, 1957

By Clarence Karr

In 1955 the Federal Bureau of Mines established a low-temperature tar laboratory at its new Appalachian Experiment Station in Morgantown, W. Va. The objective of the laboratory is to investigate the yields and chemical and physical properties of tars from low-temperature carbonization of coal, to investigate means of economically upgrading these tars, and to make available to industry and the public essential data for increasing coal utilization through the establishment of a new coal-chemical industry, based on the utilization of low-temperature tars. Because of the obvious economic significance of phenols, as well as the relative ease with which they can be separated and analyzed, initial research has centered mainly around this class of tar constituents. It was realized early that no listing of phenols and their physical properties existed that included enough compounds to be practicable. The purpose of this paper is to make such a compilation available.

Jan 1, 1957

By W. L. Dare

This publication is one of a series by the Federal Bureau of Minus describing methods and costs of minim, uranium on the Colorado Plateau. The La Sal mine is in the Big Indian mining district, about 29 miles southeast of Moab, San Juan County, Utah. The claims that encompass the mine were located in March 1953, and the La Sal ore body was discovered as a result of a drilling program begun in August 1953. The mine is owned by the La Sal Mining & Development Co., a subsidiary of the Homestake Mining Co. Homestake continued the drilling program and in May 1954 began sinking a 572-foot shaft and constructing a surface plant. The plant and shaft were completed in October 1954. The La Sal ore body is in the Chinle (Triassic) formation. it is tabular and dips with the enclosing beds about 8° southwest. The ore body is generally 4 to 8 feet thick but in a few places is as much as 20 feet thick it is being developed by a series of strike drifts and dip inclines, driven within the ore stratum on about 100-foot centers. A haulage level driven beneath the ore body is connected by raises to the upper workings.

Jan 1, 1957

By Ruth F. Brinkley

This report is the 16th of a series of reports originally issued annually and more recently biennially to acquaint the reader with the work of the Explosives and Physical Sciences Division, Region VIII.3/ In the majority of instances the results of the investigations are made available to the public through Government publications and journal articles. In certain instances (specifically as regards security-classified research, investigations of a confidential nature, and short-range programs of very limited scope) results are reported only to those immediately concerned.

Jan 1, 1957

By R. B. Bauder

In connection with a Bureau of Mines research program on utilization of Cuban lateritic ores, a comprehensive review was made of the chemical literature on nickel and cobalt. Initially, the review had as its objective the selection, from the voluminous literature dealing with the chemistry of these two metals, of only those references to reactions that were especially pertinent, or at least closely related, to the field of extractive metallurgy. Later, the coverage was extended to include references to the techniques and plant applications of extractive metallurgical procedures for the recovery of nickel and cobalt. In this report, the period from January 1929 to July 1955 has been covered, as it seemed logical that recent literature should be of greatest value. This cutoff date was established in order that the bibiliography could be issued at an early date, inasmuch as currently much work is in progress on the lateritic ores. Later, a supplement will be prepared extending the coverage to about 1900.

Jan 1, 1957

By John P. Harmon

Vehicles traveling on untreated dirt and gravel roads at open-pit mines disseminate high concentrations of dust (fig. 1). Excessive dust creates safety hazards by reducing visibility and may endanger the health of the men who breathe it. If the dust contains free silica, it can cause silicosis. In addition, maintenance costs of mechanical equipment are increased if equipment is operated in extremely dusty places. Dust on haulage roads in hot, arid country can be controlled if the surface of the road is sprinkled frequently and adequately with water. Often, when roads are sprinkled with water to control the dust, hazards are caused through reduced traction and skidding because of the mud that is formed on the surface of the road. Reducing the amount of water used will help to reduce the hazard of skidding.

Jan 1, 1957

By Robert F. Pettit

This paper on methods and costs of mining and milling iron ore at the Iron Mountain mine of Ozark Ore Co., St, Francois County, Mo., is one of a series of Bureau of Mines reports on methods, practices, and costs of mining and milling throughout the United States. The Iron Mountain operation is notable for its successful transition from open-pit to underground mining, for use underground of large earth-moving equipment, and for development of a multilevel room-and-pillar mining method. Milling methods also have undergone transitions - from hand sorting and log washing in the early days to gravity concentration. Milling ultimately may include flotation to recover additional iron from products now discarded as tailing,

Jan 1, 1957

By W. Dan Walker

In recent years the Federal Bureau of Mines tested and approved four new types of self-contained breathing apparatus and a facepiece designed for use with the McCaa 2-hour self-contained oxygen breathing apparatus. The Bureau also developed and perfected a battery-powered lifeline telephone for use in mine rescue and recovery operations. Some of this equipment is described in Bureau of Mines Information Circular 7413.4/ This publication is a revision of information Circular 7413 and presents pertinent information on more recently developed mine rescue equipment. The breathing apparatus described herein are 1/2- and 3/4-hour sell-contained types of much simpler design than the conventional 2-hour self-contained oxygen breathing apparatus ordinarily used by mine rescue crews; however, it is just as important to select rescue crews carefully and to train them properly in the use, care, and limitations of the newer types of apparatus as well as the older, established types, if the newer types are to be used safely. The Bureau of Mines recommends that 1/2- and 3/4-hour self-contained breathing apparatus be used only as auxiliary equipment in mine rescue and recovery work and that the capabilities and limitations of the apparatus should be well understood by those who wear the equipment.

Jan 1, 1957

By G. E. McElroy

Ventilation-pressure surveys are required to determine the rates of pressure losses in various parts of mine-airway systems. These may be determined directly by differential pressure measurements or deduced from absolute pressure measurements, Despite the confusion caused by its inverted nonlinear scale, the altimeter has special application to pressure surveys in mines in which only small differences in elevation are involved, as is true for most of our large bituminous-coal mines in these, the judicious use of information obtained by pressure surveying can result in greatly improved working conditions as regards health and safety and, in many instances, can yield large financial returns. The main purposes of this report are to discuss methods of using altimeters for pressure surveys and to present the particular methods of making surveys and calculating the results of surveys used by the Mine Ventilation Section of the Bureau of Mines.

Jan 1, 1957

Unfortunate occurrences resulting in injuries, loss of life, and destruction of property by explosion, fire, and other mishaps during shaft sinking in the past few years have focused the attention of the Bureau of Mines on the need for safety standards for such operations. Several States have some rules and regulations applicable to local conditions, and several Bureau publications (including some now out of print) cover the hazards that may be encountered in shaft sinking. Certain requirements of the Federal Mine Safety Code and Federal Coal Mine Safety Act may be applied, but there are no definite, uniform standards that will guide those desiring to sink a shaft safely and bring about uniform safety inspections.

Jan 1, 1957

By W. L. Dare

This information circular is one of a series the Bureau of Mines plans to publish describing the methods and costs of mining uranium on the Colorado Plateau. The Temple Mountain mining district is unique among the uranium-producing areas on the plateau. This relatively isolated mining district is in Emery County, Utah, on the eastern flank of the San Rafael Swell, about 35 miles southwest of the town of Green River. The district lies just within the eastern escarpment of the San Rafel Reef - a rampart of rugged and tilted sandstone cliffs that encircles the highly eroded core known as the Sinbad Country. The presence of petroleum matter found associated with the ore deposits, the occurrence of uranium in various formations, and the structural deformation caused by collapsed features have aroused a great deal of geologic interest. Mine development on Calyx Flat is distinctive, in that the ore deposits are worked through 36-inch calyx-drill holes.

Jan 1, 1957

By W. H. Young

The thickness of the coal seam is one of the more important items influencing the productivity and general overall efficiency of operation 1 of a coal mine. The average thickness of coal seams mined in the United States decreased 2 inches between 1950 and 1955 to an average of 62 inches, which also is 3 inches less than the 65 inches in 1945. The decrease in thickness is due partly to the increased production from strip mines with thinner seams and partly to the increased percentage of total production at underground mines in certain States having thinner seams. The thickness of seams at auger mines was measured for the first time in 1955 and was 53 inches. Though bituminous coal and lignite is mined today from seams of exceedingly variable thickness -less than 2 feet to ore than 50 feet -a large majority of the production, 65 percent in 1955, came from seams 3 to 6 feet thick. This is not surprising since the coal seam of moderate thickness presents the least mining difficulties.

Jan 1, 1957

By J. J. Shields

With the increased use of mechanized equipment in mining bituminous coal, production panels are mined out rapidly. To keep current with the rapid completion of production panels, development work must be speeded up also. Although the same type of equipment usually is employed in development as in production places in the same mine, past output per man for development usually was less than from production panels. A study of development practices in 14 mines reveals a tendency toward equalization of the output per man between development and production.

Jan 1, 1957

By E. Robert Ruhlman

["Phosphate rock" is a broad term applied to natural deposits of minerals valued chiefly for their phosphorus content. More specifically, phosphate rock may be defined as a natural rock containing one or more phosphate minerals, usually calcium phosphate, of sufficient purity and in sufficient quantity to permit its use directly, or after beneficiation, in the manufacture of phosphorus-bearing products. The grade or quality of phosphate rock is expressed either in terms of its phosphorus oxide (P20S) content or the equivalent in tricalcium phosphate (Ca3(P04)2). The trade name for tricalcium phosphate is bone phosphate of lime (B. P. L.).]

Jan 1, 1958

By J. G. Kirby

According to the Bureau of Mines annual survey, there were 319 petroleum refineries in the United States as of January 1, 1957 capable of processing 9,123,674 [ ]-barrels of crude oil daily. This was the first time in eleven years that the total number of refineries increased. The crude throughput capacity of the refineries increased 491,284 barrels daily (6 percent) above the January 1, 1956 capacity. The East Coast and Texas Gulf Coast refining districts accounted for 60 percent of the additional capacity installed. Three new refineries were put into operation on the East Coast during the year with a total daily crude throughput capacity of 154,434 barrels while the other refineries in the district report a net loss in capacity, installing equipment capable of processing 140,000 barrels, but dismantling equipment with a capacity of 150,100 barrels. In the Texas Gulf Coast district, one new refinery with a daily crude oil capacity of 5,000 barrels was placed in operation in 1956 and 143,700 barrels of crude capacity was added to existing refineries. The capacity of the average refinery to process crude oil increased from 27,145 barrels daily to 28,601 barrels in 1956.

Jan 1, 1957

By Joseph A. DeCarlo

The annual survey of the oven-coke industry by the Bureau of Mines, United States Department of the Interior, described in this report shows that 79 plants were operating in 22 States December 31, 1956. On that date 15,923 serviceable ovens existed, with a maximum total annual coke capacity of 79,965,100 net tons, and 631 new ovens were under construction. Their annual coke capacity was 3,307,300 net tons. The number of serviceable ovens in existence relates only to those capable of producing coke and does not include (1) any ovens that were blanked off or retired permanently in batteries that were operating December 31, 1956, and (2) ovens that had been demolished and were being rebuilt on that date. For this reason, the number of ovens at furnace plants reported by the Bureau of Mines at the end of each calendar year differs from the number reported for the same group by the American Iron & Steel Institute, as the institute includes ovens being rebuilt.

Jan 1, 1958

By Eugene T. Sheridan

The 23d annual survey of the peat industry by the Bureau of Mines, United States Department of the Interior, revealed that 75 producers in 17 States re-ported commercial production of peat in 1956. Forty-seven producers reported humus production, 19 reported reed-sedge peat, 17 reported moss peat, and 1 reported muck. This total exceeds the number of active operations, but several producers reported recovering more than one type of peat. Fifty-five percent of the total production was reported as peat humus, 30 percent as reed-sedge peat, and 15 percent as moss peat. A negligible amount was reported as other types. More than one-fourth of the total output was raw peat with no preparation, other than having been air-dried. The remainder consisted of processed peat prepared for use by cultivation, shredding, or kiln drying.

Jan 1, 1958

By Eugene T. Sheridan

The 22d annual survey of the packaged-fuel industry by the Bureau of Mines, United States Department of the Interior, revealed that 26 plants in 8 States were in operation and reported production in 1956. The demand for packaged fuel in the United States has declined gradually since the end of World War II, and the number of operating plants has decreased from 70 in 1946 to 26 in 1956. Annual productive capacity of the industry has decreased also during this period, and the decrease in capacity was about proportional to the decrease in operating plants. Packaged-fuel plants are relatively small, and 85 percent of the active plants in 1956 had an annual capacity of less than 10,000 tons. The same situation prevailed in 1946, when 84 percent of the plants had a capacity of less than 10,000 tons. Total capacity for the 26 active plants in 1956 was 174,600 tons, an average of 6,715 tons per plant. Operating rates in 1956 were the highest since 1951, and the rate of production for the industry averaged 37 percent of capacity.

Jan 1, 1958

By Eugene T. Sheridan

The annual survey of the fuel-briquet industry by the Bureau of Mines, United States Department of the Interior, revealed that 21 fuel-briquet plants in 11 States were in operation and reported production in 1956. The demand for fuel briquets in the United States has gradually declined since 1948, and the number of operating plants has decreased from 36 to 21. Also, the annual productive capacity of the industry has decreased, although not a proportionate amount because most of the plants that were abandoned were small and in most instances had a designed capacity of less than 25,000 tons per year. In 1956 the 21 active plants had an annual capacity of 3.7 million tons (table 2), which was only 20 percent less than the total capacity of the 36 plants in 1948. This indicates that most of the larger plants have remained active, even though operating at reduced rates, and the average capacity of the industry has increased from 130,000 tons per plant in 1948 to 177,000 tons in 1956. Since 1948 operating rates have decreased from 67 percent to 41 percent of annual capacity.

Jan 1, 1958