Search Documents

By W. S. Urbanski, A. L. Devernoe, M. S. Walker

Theory and practice are described for a new processing method capable of precise mineral separations based primarily on differences in particle specific gravities at specific gravity split points from 1.5 to 21.0 and beyond. Separations are analogous to those achieved using rotating heavy media, except that the effective specific gravity of the fluid is created magnetically using a relatively dilute, low-viscosity, water-based magnetic fluid. Results reported here for a large, laboratory flow-through separator include: 1) 99% grade with 97% recovery in single pass separation of a suite of heavy minerals from quartz at I0 kg/h, 14 tph/rm2 of duct cross section, 2) 90% grade and recovery in single-pass separation of mixtures of sand-size, non-magnetic rutile (4.23 specific gravity) and zircon (4.72 specific gravity) at throughputs of 35 kg/h, 47 tph/rm2 of duct cross section, 3) partition curves having Ep90-10 transition widths 5% or less of mineral specific gravities, and 4) essential confirmation of the theory.

Jan 1, 1991

By A. Khoshnevisan

Molybdenum resources around the world are mainly associated with porphyry copper ores. Molybdenite (MoS2) is the main Mo mineral that has rhenium in its crystal lattice. This paper investigates the recovery of rhenium and molybdenum from a molybdenite concentrate using a hydrometallurgical treatment method. The molybdenite concentrate is leached with nitric acid and subjected to solvent extraction to recover and separate rhenium and molybdenum from the leached liquor. The effects of pH and the chemicals? concentration on extraction characteristics of Mo and Re are investigated to define the best condition for selective extraction of these metals. The tested leached liquor contained of 8.2 g/L Mo, 1.5 g/L Fe, 0.5 g/L Cu and 60 ppm Re. A good extraction efficiency, up to 94%, was achieved for Re from the leached liquor, where the extraction of other metals, such as Fe and Cu, was negligible. In particular, at very low pH, rhenium is extracted selectively from solution, while the extraction of molybdenum is less than 10%. After removing rhenium, molybdenum was extracted with LIX984N. The selectivity of molybdenum extraction over other metals in solution was significant. Nearly 94% of molybdenum can be extracted from the solution at a pH value of -0.12, without any interference from other metal ions such as copper and iron.

By J. A. Bartnik

Flocculation, the process of coagulation or coalescence of finely divided particles, is commonly used in separating fine solids from fluids. Forces disposing of the particles to flocculate include: ionic forces of attraction, secondary entropic forces, and magnetism. Magnetic flocculation is due to a physical magnetizing process which affects suspended ferromagnetic particles. Such particles, after exposure to magnetic fields strong enough to cause reorientation of the particles and alignment of the induced magnetic poles, tend strongly to retain this induced magnetism, as the magnetic retentivity of ferromagnetic particles is a linear function of its specific surface.1 Thus, because they become small magnets with high residual magnetism, the particles become and remain attracted to one another, forming large agglomerates. Fine magnetic particles close to domain size can exhibit energies of the magnetization of the order of 105 ergs/cm3,2 which is many times greater than the energy affected by chemical flocculents. Therefore magnetic flocculation can be used to agglomerate particles having surfaces ionized with like charges and only a minute quantity of ferromagnetic material will be necessary to develop sufficient force to overcome the repulsive ionic forces and hold together relatively large masses of fine solid agglomerates suspended in fluids. Since flocculation occurs after the fine suspension passes through a magnetic field generated by magnets surrounding a pipe section, the simplicity of the process and economic advantage makes magnetic flocculation very attractive.

Jan 1, 1971

By C. Wen

In Huoqiu region of Anhui Province, Fe2O3 occurs mainly in the form of specularite. Besides quartz, the gangue minerals include iron-bearing silicates such as chlorite and sericite which account for about 10% of the total gangue. The separation effect of conventional collectors is poor in the flotation of the minerals, that is, the average grade of iron concentrates is only 60-62%. Using the developed amphoteric collector can successfully realize not only the separation of specularite from various gangue minerals with results of iron concentrate grade above 65% and iron recovery of above 80% but also low temperature flotation at 15°C.

Jan 1, 2012

By A. H. Hassan

Stibiotantalite is a relatively rare mineral not commonly found in the major tin districts of the world, and its separation characteristics have not been documented adequately in the literature.

Aug 1, 1979

By S. K. Kawatra, T. C. Eisele

To reduce their sulfur emissions, many coal-fired electric power plants use wet flue-gas scrubbers. These scrubbers convert sulfur oxides into solid sulfate and sulfite sludge, which must then be disposed of. Currently, the major markets for scrubber sludge are for manufacture of gypsum products, such as wallboard and plaster, and for cement. However, the quality of the raw sludge is often not high enough or consistent enough to satisfy manufacturers, and so the material is difficult to sell. Other markets, such as paper manufacture and plastics fillers, have even more stringent quality requirements and will not accept raw sludge at all. In the work described in this paper, several reagents have been examined to determine their ability to selectively improve the flotation of the unreacted limestone contaminant away from the desirable products (calcium sulfite and gypsum). The most success has been achieved using a cationic collector, which shows a higher selectivity between calcium sulfite and calcium carbonate than do the anionic collectors that were studied.

Jan 1, 1995

By E. H. Cho, P. K. Dai

An acid mine drainage sludge sample, containing 3.6% Mn, 0.18% Ni, 0.15% Co and 0.39% Zn, was obtained from central West Virginia. The sample was leached at room temperature with a pH 3 sulfuric acid solution. Air was then bubbled through the leach solution at pH 4.5 to precipitate the iron. The leach solution contained 258 ppm Zn, 105 ppm Ni, 90 ppm Co and 2050 ppm Mn. Three solvent extraction studies were performed to selectively extract these metal ions in a sequential operation with DEHPA. Cyanex 272 and Lix 84. The A/O ratio was one, and the extractants were diluted ten times with kerosene. A study of solvent extraction with DEHPA showed that Zn could be extracted without Ni or Co up to a pH of 2.75. A pH of 2.75 is considered to be the optimum pH to maximize the selective separation of Zn from Mn. The separation factor of Co over manganese suggests that the two metal ions should be extracted together by Cyanex 272. The separation factor of Co over Ni indicates that these two metal ions can be separated most effectively around pH 5.3. Also, Ni can be effectively extracted by Lix 84 above pH 5.5.

Jan 1, 1995

By E. H. Cho

An acid mine drainage sludge sample containing 3.6% Mn, 0.18% Ni, 0.15% Co and 0.39% Zn was obtained from the central part of West Virginia and leached with sulfuric acid at pH 3 and at room temperature. Air was bubbled through the leach solution to precipitate the iron content from the solution at pH 4.5. The leach solution contained 258ppm Zn, 105ppm Ni, 90ppm Co and 2050ppm Mn. Three distinctive solvent extraction studies were performed to selectively extract these metal ions in a sequential operation with DEHPA, Cyanex 272, and then Lix 84. The AIO ratio was 1 and the extractants were diluted 10 times with kerosene. A study of solvent extraction with DEHPA showed that Zn could be extracted without Ni or Co up to pH 2.75. A pH of 2.75 is considered to be the optimum pH to maximize the selective separation of Zn from Mn. The separation factor of Co over manganese suggests that the two metal ions be extracted together by Cyanex 272. The separation factor of Co over Ni indicates that these two metal ions can be separated most effectively around pH 5.3. Also, Ni can be effectively extracted by Lix 84 above pH 5.5.

Jan 1, 1993

By Donald S. Bubar

The Separation Rapids property, located approximately 60 km (37 miles) north of Kenora, Ontario, Canada, is host to one of the largest rare metal pegmatite deposits in the world. This pegmatite was named the Big Whopper by its discoverer, Dr. Fred Breaks of the Ontario Geological Survey, because of the exceptional length and width of the surface exposure. The property is readily accessible from a main, all-weather road via a network of secondary logging roads. The main line of the Canadian National Railway passes through the village of Redditt, just 40 km (24 miles) south of the property. The Big Whopper is one of the complex-type (petalite sub-type) class of rare metal pegmatites that are geochemically the most highly evolved in the spectrum of granitic pegmatites. Such deposits are economically important as resources for the rare metals lithium, tantalum, cesium, and rubidium. While complex-type pegmatites are found in many areas of the world, most are too small to be profitably mined, however, with an inferred resource in excess of 15 million metric tons (mt) (17 million short tons [st]), the Big Whopper is only the fourth deposit of its type in the world with the size required to be of major economic importance. The other three deposits, which are currently in production, are the Tanco mine in Manitoba, the Bikita mine in Zimbabwe, and the Greenbushes mine in Western Australia. The Big Whopper is situated in the eastern continuation of the Archean Bird River greenstone belt which also hosts the Tanco pegmatite, approximately 60 km (37 miles) to the west. The principal commodities identified in the portions of the Big Whopper pegmatite explored to date are petalite (LiAlSi4010) and rubidium-rich K-feldspar. These are industrial minerals with important applications in the glass and ceramics industries. The Big Whopper also contains substantial quantities of lepidolite, a lithium, rubidium-mica which is the principal ore mineral for rubidium metal. Tantalum and cesium occur in anomalous levels with the petalite mineralization, and the possibility of finding zones of high enrichment in these valuable high-tech metals elsewhere in the deposit is excellent. Such enriched zones are typical of pegmatites as highly evolved as the Big Whopper. To date, the geological mapping and diamond drilling work completed by Avalon have delineated the Big Whopper pegmatite system over a strike length exceeding 1.5 km (0.9 miles), over widths ranging from 10 m to 80 m (30 feet to 260 feet) in thickness, and to a vertical depth of close to 300 m (1,000 feet), where it remains open. The pegmatite system consists of a vertically oriented massive petalite pegmatite dyke striking 280 degrees that is flanked by amphibolites containing a swarm of narrower albite and petalite dykes which have all undergone intense deformation in a high strain zone resulting in folding and intense shearing. The Big Whopper exhibits a mineralogical zonation pattern which is complicated by the superimposed deformation that has both folded and stretched the deposit. Drilling has defined a dilute geological resource totaling 7.1 million mt (7.8 million st) grading 1.283 percent Li20, 0.346 percent Rb20, and .007 percent Ta205 over a strike length of 600 m (2,000 feet), and to a vertical depth of 250 m (820 feet), where it remains open. The petalite and rubidium-rich-K-feldspars contained in the Big Whopper all appear to be of superior quality. The grades are consistent with a petalite content averaging 25-30 percent and a rubidium-rich-K feldspar content averaging 15-20 percent. The remainder of the rock consists mainly of albite, several types of mica, and quartz. Accessory minerals include columbitetantalite, cassiterite, apatite, garnet, and gahnite. Market studies show that the deposit is located close enough to existing transportation infrastructure to access rapidly growing, major markets in the glass and ceramics industries, both in the northeastern U.S. and Europe. There are only three competing lithium minerals producers in the world with the Bikita mine in Zimbabwe being the only major producer of petalite. The other lithium deposits produce spodumene, a less desirable lithium mineral. Lakefield Research Limited has successfully designed a process to produce an ultra-pure petalite concentrate containing up to 4.65 percent lithium oxide, and as little as 0.014 percent iron oxide, low levels of soda and potash, and negligible amounts of other trace elements. With these specifications, Avalon will have an excellent quality product for glass-ceramics applications such as Corningware®, CERAN® stove tops, and other thermal shock-resistant products. Lakefield is presently designing the balance of the flowsheet to produce separate concentrates of rubidium-rich K-feldspar, albite, mica, tantalum, tin, and high-purity quartz. Initial test work indicates that the feldspar products will be of exceptional quality. The K-feldspar concentrates contain 11-12 percent K20 and 1 percent Rb20, while the sodaspar contains over 10 percent Na20, and both have very low iron (0.01 percent Fe203). A preliminary economic model shows that with an initial production rate of 90,000 mt (100,000 st) per year, expanding to 170,000 mt (190,000 st) per year over 5 years, the project is capable of generating over CDN $10 million per year in pre-tax cash flow by year 5 on a capital cost of approximately CDN $30 million.

Jan 1, 2001

By Ahmed I. A. Salama

The problem of estimating separation characteristics by utilizing mass distributions of feed and products is considered. The separation characteristics include mass yield and partition curve. The cases of mass balance and partition functions balance are identified. The developed techniques can handle the cases of two- and three-product separation. Actual data are utilized to demonstrate the proposed techniques.

Jan 1, 1992

By B. Li

"Sepiolite is a magnesium-rich, porous, and fibrous clay mineral with broad applications. These applications take advantage of sepiolite’s high specific surface area and unique nano-sized channel structure. Over the past years, numerous materials and techniques based on the structure and property of sepiolite have been developed. This article reviewed the recent achievements in developments and applications of sepiolite in environmental protection, catalysis area, and nanocomposites. The prospectives of sepiolite applications is also discussed. INTRODUCTION Sepiolite is a magnesium-rich, porous, and fibrous clay mineral. The typical chemical formula of sepiolite is Si12Mg8O30[OH]4[OH2]4·8H2O [1]. Sepiolite has a high specific surface area and nano-sized channels because of its special structure [2]. This unusual crystal structure projected onto the [001] plane is shown in Fig.1 [3]. As it can be seen, silicon and oxygen atoms make up for the tetrahedral structure and magnesium and oxygen atoms form octahedral structure, respectively. Those tetrahedral-octahedral-tetrahedral ribbons expand boundlessly in one direction, leading to the special fibrous structure of the sepiolite. Every tetrahedral-octahedral-tetrahedral ribbon is combined to the next by an inverted Si–O–Si bond, which causes an interlaced layer with a continuous tetrahedral sheet and a discontinuous octahedral sheet. Terminal MgO at the edges of the ribbons is coordinated with two structural water molecules, which can form hydrogen bonds with zeolitic water molecules that are located in the channels running parallel to the fiber axis [3,4]. The Mg2+ ions inside the channels can be exchanged with other cations in solution. Therefore, sepiolite can be used to remove metal cations from aqueous solutions [5,6].It can be seen from Figure. 1 and Table 1 [7], the unique structure endows sepiolite with a substantial surface area and nanoscale channels. Its specific surface area reaches 320 m2/g and channel dimensions up to 3.7×10.6 Å. There are three active adsorption sites on the surface of sepiolite: one is oxygen atoms of the Si-O tetrahedron. The second is the structural water molecules paired with magnesium ions at the edges of the ribbons, which can form hydrogen bond with adsorbent. The last one is the Si-OH groups due to the breaks of the Si-O-Si bonds on the surface of Si-O tetrahedron. Thus, sepiolite has strong adsorption ability which has been widely used in environmental protection. Moreover, sepiolite has many significant features such as good mechanical and thermal stability, rheological property, porous, and easily modification, making it be a hotspot in chemical and biological researches. However, with the development of technology, broader and more advanced applications of sepiolite have been carried out in recent years. In this study, the recent achievement in sepiolite applications is summarized, the further tendency is also discussed."

Jan 1, 2018

By Stephen Njoloma, William Bracken, Harald Cordes, Ivan Hee

"DC Water’s First Street Tunnel (FST) is part of the $2.6 billion Clean Rivers Project designed to reduce the occurrence of combined sewer overflows into local waterways. Due to flood events in the Bloomingdale and LeDroit Park neighborhoods, the FST Project was accelerated by DC Water to mitigate future flooding by boosting storage capacity and thus relieving the undersized combined sewers.The FST Project was finalized in 2016 as a collaborative effort between DC Water, its consulting team consisting of Greeley & Hansen and McMillen Jacobs Associates, and the design-build team of Skanska, Jay Dee Contractors (SKJD) with WSP Parsons Brinckerhoff as the designer.Scope of project. The FST Project (Fig. 1) included four primary shaft sites, a large 6 m (20 ft) internal diameter, 823- m (2,700-ft) long bored tunnel and three adit connections from the off-line shafts to the large-diameter tunnel. The adits which vary in size and length, are the subject of this article. The Channing Street site (Fig. 2) was established as the main site for an Earth pressure balance tunnel boring machine (TBM) and included a 49-m (160-ft) deep shaft with slurry wall support of excavation and 20-m (65-ft) internal diameter final cast-in-place permanent concrete liner. The construction sites at Adams Street, V Street and Thomas Street each consisted of off-line shaft structures tied to near-surface sewer diversion chambers and ventilation facilities. These three off-line shafts were connected to the large bored TBM tunnel via adit tunnels. Each of the three adits had a portion or the entire length excavated by sequential excavation method (SEM) in frozen ground.The Adams Street adit (Fig. 3) was constructed in two phases. The first phase is the 23-m (75-ft) long and 5-m (16-ft) diameter section immediately outside the drop shaft which also serves as the deaeration chamber and was excavated by SEM. The second phase which is 91 m (300 ft) long and 3 m (10 ft) in diameter was excavated by Micro TBM (MTBM) launched from within the permanently lined deaeration chamber. MTBM excavation commenced toward a reception chamber that was excavated by SEM from the previously bored FST TBM tunnel. This SEM excavation had a 5 m (17 ft) diameter and a length of 4.5 m (15 ft)"

Jan 3, 2018

By Richard Jr. Ray, David Johnston, Phil Blankenship

Injection of inert gases to combat mine fires has been practiced in various parts of the world for a long time. Of late, nitrogen has become the preferred inert gas for control of mine fires and safe salvage of longwall equipment as compared to carbon dioxide or fuel gases produced from burning of fuel. In India, carbon dioxide has been used for fire fighting in a number of mines during the 1960s and 1970s. More recently inert gas produced from burning of fuel oil in surface plants has been used in controlling the atmosphere in fire areas in two mines. In yet other cases, liquid nitrogen has either been poured directly into fire areas in liquid form or injected in gaseous form to keep the fire in check. Nitrogen produced in liquid form in an oxygen plant is more costly than nitrogen produced from PSA (pressure swing adsorption) based plants. A PSA-based plant has been installed in one of the Indian mines in 1986 and more are in the offing. This paper reviews the application of various inert gases in Indian mines and discusses the likely trend of inert gas application in Indian mines in the future.

Jan 1, 1989

By F. C. Turin, T. L. Friend, A. G. Mayton, J. S. Jaspal, W. J. Wiehagen

This paper describes the serious injuries that have occurred to bulldozer operators working at domestic coal, metal and nonmetal mines in the United States. A serious injury is defined as one that results in either a fatality or in lost work time. Examined were 873 injury records compiled by the Mine Safety and Health Administration (MSHA). The time period covered was 1988 through 1997. These injuries resulted in 18 fatalities and 31,866 lost work days. All of these injuries occurred to dozer operators while they were performing common production tasks. An injury classification system was developed to code the narrative information that describes the circumstances surrounding the injuries. Jolts and jars accounted, for 604 or 70% of the serious injuries to bulldozer operators, and jolts and jars accounted for 75% of the workdays lost. Vertical jars comprised the largest set (354 incidents) of jolting and jarring injuries. In more than half of these incidents, the operator was backing up the dozer. Working near an edge carries significant risk for fatal injuries. Of 116 incidents where the dozer fell over an edge, rolled over or fell into a hidden void, 14 (12%) resulted in fatal injuries. In cases where the dozer operator either jumped or was thrown out of the cab in a fallover or rollover, seven out of 17 of the operators were killed. This study finds that further reductions in injury risk would require more widespread use of seat belts; consideration (and maintenance) of the seat and seat suspension systems that might reduce injury risk from jolts and jars; research interventions to assess the effect of alternative engineering designs to dampen or isolate the effects of shock and vibration; and continued attention to skilled performance, i.e., the integration of hazard awareness, recognition and response with dozer operational skills.

Jan 1, 2003

On my arrival in New York after the Russian examinations John D. Ryan, president of Anaconda, asked me what my plans were. I told him I wanted to be useful somehow in the World War that we had entered while I was away, but I did not know how. Ryan and Thayer told me that the new American Air Corps was gathering a group of executives, most of them young, to go to France as Army officers to help with the industrial side of our aviation activities. This would include construction of military airports, maintenance, and supply for our rapidly growing Air Corps. They thought I might be accepted in this group of about 30. It seemed to be just what I wanted, and I put in my application at once. My application was accepted about three weeks later and I was told to come to Washington to take physical and other tests and to meet others of the group. I liked them. They were a cross section of competent American manufacturers, bankers, automobile executives, and merchants. I was the only miner. I had many discussions in the days in Washington with members of our organization and others I knew who were going into war service. Attitudes were very different from those 55 years later. There was no discussion as to whether war was right or wrong. We were in it and must do all we could to help. At the same time there was a holdover from the days when, at least for the elite, war was high adventure. Even the most high-minded did not then realize that war is a horrible form of wholesale murder and, in 1917, it would have been treason to suggest this. I had two weeks before our industrial group was to start work which gave me time for a hurried trip to Berkeley where Dorothy and I announced our engagement.

Jan 1, 1976

"The Ohio River Bridge East End Crossing Tunnel requires a 75-year service life of its cast-in-place reinforced concrete lining. This twin-tube 3-lane (each tube) highway tunnel is about 55-ft wide and 30-ft high. Since unified tunnel service life prediction methodology does not exist in the US, challenges occurred during the design-build phase of this project. These challenges include the methodologies in determining the reinforced concrete’s degradation mode, the lining’s surface chloride concentration level, the reinforcing steel’s critical chloride threshold value for corrosion, how to verify the concrete’s diffusion coefficient, and the durability impact from concrete crack width. This paper presents a methodology in verifying the proposed concrete mix can achieve the service life requirements. This methodology can be adopted for service life prediction for future tunnels to be built in the US. INTRODUCTION The Ohio River Bridge East End Crossing (ORBEE) Tunnel is part of a Public Private Partnership project, which connects transportation network between Louisville, Kentucky and southern Indiana. Located in Louisville, Kentucky, the twin-tube highway tunnel provides northbound and southbound lanes of the Kentucky approach to a new bridge across the Ohio River. Tunnel lengths are approximately 1,675-ft and 1,685 for the northbound tube and the southbound tube, respectively. Connected by two cross-passages, both tubes have a roadway width of 40-ft, for 3-lane traffic, and a vertical clearance of 26.5-ft.The tunnel was constructed by drill and blast method with shotcrete and rock dowels as initial ground supports. The final tunnel lining system includes: •,Nominal 16” cast-in-place reinforced concrete lining, with 2” and 3” concrete covers over reinforcing steel for its extrados and intrados, respectively. •,20” cast-in-place reinforced concrete invert slab, with 4” and 3” concrete covers over reinforcing steel on its top face and bottom face, respectively. •,PVC waterproofing system around tunnel perimeter, excluding invert slab. •,Perforated PVC groundwater collection pipes on both sides of the tubes and one below the invert slab of each tube."

Jan 1, 2016

By M. Rossi

The use of service variables in geostatistics (grade-thickness) is common in industry when developing block grade models and geologic resource estimates. This is particularly true in the case of sedimentary and stratabound-type deposits. The approach has proven merits when assessing ore reserves. However, there are cases where its application for preliminary data analysis produces biased estimates. One such case is encountered in uranium disequilibrium studies. This paper demonstrates the inadequacy of service variables when performing uranium disequilibrium studies. Disequilibrium analysis is a necessary preprocessing step when radiation counts are used as raw data to calculate uranium reserves. Typically, a probe is used to obtain the gamma counts from open drill holes. These counts are then regressed (and corrected) against chemical assays obtained from core samples. During this process the grade-thickness variable produces an optimistic image of the relationship between probe grades and chemical (true) grades, causing overestimation of the final geologic resource. The problem is analyzed through a case study.

Jan 1, 1993

By M. Rossi

The use of service variables in geostatistics (grade-thickness) is common in industry when developing block grade models and geologic resource estimates. This is particularly true in the case of sedimentary and strata-bound-type deposits. The approach has proven merits when assessing ore reserves. However, there are cases where its application for preliminary data analysis produces biased estimates. One such case is encountered in uranium disequilibrium studies. This paper demonstrates the inadequacy of service variables when performing uranium disequilibrium studies. Disequilibrium analysis is a necessary pre-processing step when radiation counts are used as raw data to calculate uranium reserves. Typically, a probe is used to obtain the gamma counts from open drill holes. These counts are then regressed (and corrected) against chemical assays obtained from core samples. During this process, the grade-thickness variable produces an optimistic image of the relationship between probe grades and chemical (true) grades, causing overestimation of the final geologic resource. The problem is analyzed through a case study.

Jan 1, 1991

By Robert L. Sundeen, Richard V. Wenberg

Service vehicles, often called support vehicles or auxiliary vehicles, are used in secondary functions to support production activities such as loading, drilling, and timbering. Probably the most common support vehicles are the personnel carriers used to move miners to and from work areas. Utility designs are used to transport supplies and various less mobile equipment. Specific application designs are used for special work such as explosives transportation and loading, equipment maintenance, and equipment lubrication. PERSONNEL CARRIERS Personnel carriers are available in a wide variety of sizes and configurations. Some are two-wheel drive, though most are four-wheel drive. Smaller versions carry at least two men and usually have sufficient capacity to carry a small payload of supplies or equip¬ment. The American Motor's 05 Jeep, equipped with an optional diesel engine, has been adapted successfully for this light duty. Larger personnel carriers with ca¬pacities of 12 to 20 or more men currently are available, as shown in Fig. 1. The designs often are customized to the operating characteristics of each mine. All meet the latest federal requirements for rollover protection, emergency brake systems, etc. UTILITY VEHICLES Utility vehicles are adaptable to numerous duties. Probably the most common are ordinary haulers with a flat bed or low-sided box. They are used for hauling supplies and equipment from one point to another. Some occasionally are used for towing and may pull one or more trailers. Fig. 2 shows a typical utility truck. SPECIAL-APPLICATION VEHICLES Special-application vehicles are possibly the most important of all support types since these vehicles di¬rectly support and maintain production equipment. Such vehicles are available in a wide variety of sizes, mechanical functions, and operating specifications. Most versions are four-wheel drive and articulated. Among the more common vehicles are explosive haulers and loaders, mechanic's trucks, lubrication trucks (Fig. 3), and special carriers. TYPICAL APPLICATIONS Development Utility haulers are essential in trackless operations to bring supplies to advancing headings. Some utility haulers may be dedicated to bringing in steel sets and may be equipped with boom lifts to unload heavy sup¬ports or even place them as required. A rockbolt hauler may have a boom-mounted operator's basket which can be used for bolt installation or inspection. Various mechanic's trucks and pipe trucks service the heading to keep power, air, water, and ventilation at the face and to keep face equipment at maximum utilization. Production Production operations require a variety of support equipment. Because of the larger crew size brought about by the addition of the production force, personnel carriers play a greater role. Correspondingly, steel¬support hauling equipment and bolting trucks usually see limited application. PRODUCTION UNITS Capacity Personnel carriers are available to carry almost any number of people desired. Likewise, other types of carriers or haulers can and are built to fit specific re¬quirements. Physical size, capacity, and operating char¬acteristics can be varied to fit any size of opening and operating condition. Generally, articulated models offer greater maneuverability than straight frame-axle steer designs. Most vehicles of this type are lower in power than production units, generally under 74.6 kW (100 hp). Operating performance still compares favorably to that of production equipment, i.e., the support vehicles can travel at equivalent speeds on the various mine gradients. Manpower Auxiliary vehicles should require only a single opera¬tor. Specific application vehicles may require more than one person. For example, ventilation trucks usually require a crew of two where pipe must be installed.

Jan 1, 1982

Paper 1: Risk of gastrointestinal cancers from inhalation and ingestion of asbestos, John F. Gamble Selikoff suggested the hypothesis that asbestos exposure is causally associated with increased risk of gastrointestinal (GI) cancers in an early study of insulation workers. In this paper, John Gamble reports on his extensive review and reanalysis studies that address the relationship between asbestos exposure and GI cancers. The purpose of the review was to evaluate the association between asbestos exposure and risks of stomach, colorectal, colon, and rectal cancers separately. Gamble evaluated exposure?response (E?R) relationships using surrogate exposure methods ??because few individual studies of GI cancer have reported exposure? response analyses.?? The principal asbestos exposure surrogates are: (1) the rate ratio (RR) for lung cancer; and (2) the percent of mesothelioma among exposed workers. Analyzing SMRs for GI cancers from individual studies versus the risk of lung cancer and mesothelioma provides crude estimates of E?Rs for asbestos exposure and GI cancer. Briefly, Gamble justifies the surrogate approach as follows:

Jan 1, 2007