Search Documents

By W. Kunda

Silver nitrate solution is a very common product in hydrometallurgical processes involving the treatment of various silver bearing materials. Silver is recovered by electrolysis. The alternative method for the recovery of silver from aqueous solutions is the precipitation by hydrogen at elevated temperature and pressure. A previous study by the authors revealed the feasibility of this technique for the silver ammine sulfate system. Further study showed different behavior for silver in the silver ammine nitrate system and a systematic study was initiated to establish the optimum conditions for the process. The study showed that the process can be controlled by (1) composition of the feed solution, (2) temperature and (3) hydrogen pressure. The recovered silver product was in the form of very fine powder.

Jan 1, 1989

By J. M. Demarthe

The recovery of minor metals from zinc concentrates is dependent on the process used for their treatment. The behaviour of gennanium and indium in pyrometallurgical processes such as the Imperial Smelting furnace or the cupola furnace is of practical importance. The .Anaconda process for the treatment of zinc leach residues is not well suited to the recovery of valuable minor metals, and new technologies must be studied. In this regard, a solvent extraction process, using Kelex 100, developed by Minenet Recherche for the recovery of gennanium from dilute sulphate leach solutions is described. Also, new hydranetallurgical techniques in chloride media can be applied to the purification and concentration of minor metals depending on the stability of their chloro-complexes and the valency of associated inpurities. A synthesis of methods is proposed to address the problems related to the recovery of valuable minor metals in the zinc industry.

Jan 1, 1990

By Jinrong (Patrick) Mang

Three of the most challenging problems in phosphate beneficiation are discussed: flotation efficiency, resource conservation and environmental impact. Some new flotation machines offer the opportunity of reducing power and reagent consumption significantly, while increasing specific capacity many fold. Efficiency might also be improved dramatically by replacing the "double float" process with a single-collector scheme. Model based software control is a powerful tool for improving overall plant efficiency. Recovery of phosphate values from the phosphatic clays could extend phosphorus reserve life significantly. phosphate recovery from the slimes might be achieved by sizing-flotation, selective flocculation and bioleaching. Reducing the volume of phosphatic clays produced is another key stop to minimizing phoephate logs. Such a reduction may be realized by floating at finer cut size. Although an ideal' dolomite separation process is yet to be developed, a cationic flotation process may prove to 'be economically feasible. Loss of phosphate in the desliming stage is the major problem with most of the flotation schemes for removing dolomite.

Jan 1, 1995

By Dachun Liu, Yifu Li, Baoqiang Xu, Yongnian Dai, Bin Yang

"The removal of impurity arsenic from crude tin is one of the major problems in the process of tin refining. Through a thermodynamic analysis on vacuum refining process of crude tin, the vapor pressure of impurity arsenic under different temperatures can be obtained, which demonstrates that it is possible to separate tin and arsenic by the vacuum refining process. This paper attempts to verify the behaviors of impurity arsenic. The experiment result shows that through vacuum distillation, crude tin with 0.16% arsenic can be refined from crude tin with 0.96% arsenic, and about 50% impurity arsenic can be collected in the form of metallic arsenic.PrefaceThe crude tin obtained by the reduction process is insufficiently pure for most applications, even smelting from tin concentrate. Arsenic is a common impurity in crude tin and also one of the predominant elements to affect tin performance. Arsenic is a poisonous metal that has long been linked to an increased risk of cancers, diabetes, thickening of the skin, diseases of the liver and digestive complications, so there is a mandatory limit on the amount of arsenic (<0.015%) in tinfoil wrapper and tin layers for food packaging. Arsenic causes a poor appearance and plasticity, and increases viscosity. The impurities content of crude tin fluctuate over a wide range; a lot depends on composition of tin ore concentrate, treatment method and technological process before reduction smelting. And the content range of arsenic is usually 0.5~4%, but it is higher in some factories."

Jan 1, 2012

By Hebi Yin

A two-dimensional multi-scale solidification model was developed to study the heat transfer, fluid flow, and grain growth occurring in the molten pool during the laser engineered net shaping (LENS) process. This model coupled the finite element method to calculate mass, energy and momentum transport in the macroscale with the cellular automaton technique to calculate liquid/solid phase change at the microscale. The validation of the model was performed by comparing the simulation results with experimental data from previously published works, showing good agreement in temperature distribution and the dendrite morphology (size and shape). The simulation results showed that Marangoni convection, caused by the temperature gradient along the pool surface, played a critical role in determining the flow pattern in the molten pool and exerted influence on the pool size and shape. It was also found that columnar dendrites can be formed, with dendrite arm spacings as fine as a few microns due to the high cooling rate during the LENS process. In addition, the influence of fluid flow on the dendrite growth in the pool was discussed.

Jan 1, 2010

By Patrick Clark

As part of the Mine Waste Technology Program (MWTP), a large-scale column test using bacteria and a sulfide ore was conducted at McClelland Laboratories, Inc., in Sparks, Nevada. Four technology providers participated in this demonstration. A mining company in Nevada provided the sulfide ore, process effluent and make-up water. A process effluent column, a chemical oxidation column, and the four biological treatment columns were set side by side on a test pad outside the laboratory building. The process effluent and chemical oxidation columns were used for experimental control. The goal of this project was to evaluate the viability and feasibility of using these biodegradation technologies to reduce the cyanide to the regulatory level of 0.2 parts per million (ppm) within an acceptable timeframe and with low operational costs. The column testing began on December 3, 1998 and operated until May 17, 1999. One technology provider reached the regulatory level within the 158 days. The remaining three biotechnology columns were approaching the regulatory limit at completion of the demonstration. The MWTP is funded by the U.S. Environmental Protection Agency (EPA) and is jointly administered through an interagency agreement with the U.S. Department of Energy (DOE).

Jan 1, 1998

Many studies have been conducted over the past 3 decades on the leaching of gold in solutions containing thiosulfate, ammonia and copper. However, most of these studies have been carried out using ore samples, with very few fundamental studies of this system being attempted. The majority of the published studies have failed to acknowledge the undesirable side reaction between copper(H) and thiosulfate, let alone account for its effect. The fact that the solution chemistry is constantly changing makes it very difficult to perform a fundamental study of gold leaching. With the advent of the rotating electrochemical quartz crystal microbalance (REQCM), such fundamental studies are possible as this instrument measures mass in real time. This has allowed leach kinetics to be measured in a matter of minutes and hence at essentially constant solution conditions; The present paper highlights that a sufficient concentration of copper(II) and ammonia are required in order to achieve appreciable gold leach rates. However, the use of air (oxygen) to maintain the copper(Il) concentration catalyses the undesirable copper(II) reaction with thiosulfate. The presence of ammonium ions is shown to have an effect on this undesirable reaction as well as on the gold leaching ?reaction. Preliminary electrochemical studies into .gold electrowinning using the REQCM show that gold(I) thiosulfate cannot be readily reduced to metallic gold in the potential region at which cementation usually occurs. However, it is well known that gold cementation onto copper occurs rapidly. The current study addresses this discrepancy by studying the effect that copper and silver have on the reduction of gold thiosulfate. It has been found that the presence of both silver and copper enhance gold deposition, particularly at low over potentials. While this is beneficial in cementation, the presence of copper and silver in solution has been found to cause passivation of the cathode surface during electrowinning at &apos;higher overpotentials.

Jan 1, 1998

By Serge Lavoie

Alcan&apos;s Guillaume-Tremblay plant, located in Jonquiere, Quebec, has been in operation since 1990. This was the first plasma dross processing plant ever built. In addition to the use of the plasma heating technology, Guillaume-Tremblay has other unique features making it a modern and efficient dross processing facility. This paper presents a general overview of the practical experience at the Guillaume-Tremblay plant. In particular, the utilization of plasma heating in industrial conditions, the metallurgical performance, the unique dross handling system, the control and information management system and the reclaiming of the by-products will be discussed. Finally, the use of the plasma process for salty dross will be addressed&apos; briefly.

Jan 1, 1995

By Metehan Erdogan, Ishak Karakaya, Fuat Erden

"Mg-Ni system draws attention due to the promising hydrogen storage properties of Mg2Ni. The proposed method involves the use of NiO and MgCl2 in an electrochemical cell to from Mg-Ni intermetallics directly. The electrodeoxidation of NiO was followed by combination of Mg and Ni in molten salt electrolytes. The products were characterized by XRD analysis and SEM examinations. The quantitative results from Rigaku supported by Rietveld Refinement method conducted by Maud showed that more than 50 percent of the input Ni was converted to Mg-Ni intermetallics.INTRODUCTIONIt is well known that fossil fuels are the most common energy producing materials throughout the last century although, they are not renewable and their usage cause critical environmental problems [1, 2]. Hydrogen, on the other hand, is known as a clean, renewable energy carrier and instead of fossil fuels; usage of hydrogen for energy production will be the benefit of mankind. However, there are problems that hinder more common usage of hydrogen such as hydrogen storage [3]. Mg2Ni is known as Mg based hydrogen storage material with high hydrogen storage capacity [3-6]. Common Mg2Ni production methods are; mechanical alloying [8-11], vacuum induction melting [12, 13], vacuum arc melting [14], combustion synthesis [15], melt spinning [16], repetitive rolling [17] and isothermal evaporation casting [18] were also used. However, in all of these, pure Mg and Ni are required to be produced previously. Therefore, difficulties arise during handling, preparation and combination of Mg and Ni due to highly reactive nature of especially magnesium (i.e. oxidation of Mg) [11, 17, 19, 20]. Although hydrogen desorption dynamics can be significantly improved with usage of nanostructured Mg2Ni [7], it is difficult and it requires very long processing durations to produce nanostructured Mg2Ni by above processes."

Jan 1, 2014

By Thierry De Nys

A direct leaching process of sulphidic zinc-based concentrates in aqueous sulphuric acid solutions has been developed by the V.M. R & D Department. By a very accurate control of the oxidation potential of the leach solution, this process enables a separate recovery of the zinc, copper, silver, lead and sulphur of the concentrate and makes it extremely attractive for treating more complex ores. The iron, solubilized during leaching, is eliminated out of the zinc solution by means of the V.M. goethite process. Alternative flow sheets for a conventional zinc electrolysis plant are presented.

Jan 1, 1990

By Yue-yuan Li

China has abundant magnesite resource, but the low-grade and powder ores have always been rejected, which influences the comprehensive utilization of resource and often causes circumstance problems. The present work investigated the preparation of magnesia whisker using magnesite tailings as starting materials by preparation magnesium carbonate whisker as precursor firstly in the route of calcination, hydration, carbonation and pyrolysis, follows by second calcination of the precursor. The influence of pyrolysis conditions and additives on morphology of magnesium carbonate crystal as well as the influence of calcination conditions on morphology of magnesia whisker was investigated. The results showed that thermal decomposition products was MgCO3?3H2O. Magnesium carbonate whisker with length of 10~60 µm and the length-to-diameter ratio of 10~20 was prepared when soluble magnesium salt was added. While temperature was elevated at 1°C?min-1, magnesia whisker with length of 10~60µm was obtained.

Jan 1, 2010

By Wayne Bell, Shivanand A. Borkar, Anish Upadhyaya, Matthew D. Andriese, Jiann-Yang Hwang, Zhiwei Peng

"A refractory ore body located in Michigan’s Upper Peninsula contains high concentrations of nickel and copper chiefly occurring in the minerals pyrrhotite, chalcopyrite, and pentlandite. Refractory ore bodies are difficult to treat by conventional mineral processing methods so microwave pre-treatment of the ore is employed to increase metallic-particle/host rock liberation by making use the differential thermal expansion properties of the mineral phases that absorb microwave energy. The Curie temperature measurement of metallic-bearing particles is in agreement with the known value for pyrrhotite occurring at 325°C. A nickel-rich iron sulfide mineral is found to be in occurrence and also appears to be magnetic under BSE imaging. It is shown the ore particles heat rapidly when exposed to microwave radiation for short durations of time mainly due to the high concentration of ferromagnetic mineral phases. Rapid heating causes thermal expansion of constituent mineral phases that produce cracks within ore particles. SEM imaging shows fracture occurring along grain boundaries and throughout host rock matrix. Ball milling experiments show an increased grindability of the ore resulting in a decrease in work index values.IntroductionCrushing and grinding operations consume 50-70% amount of energy used in mineral processing operations [1]. All these processes involve high energy impact of surfaces to develop compressive stresses that produce cracks to initiate breakage of particles. Microwave pre-treatment of certain types of ore might provide an energy savings to these type grinding processes by taking advantage of the tensional forces produced by selectively heating microwave absorbing type mineral phases. The heating of ore particles produces cracking by thermal expansion of the constituent mineral phases. Conventional heating has been investigated and shown to positively aid in grinding processes but determined energy inefficient to be used commercially."

Jan 1, 2011

By Wen-Ming Chien

Keywords: AN-KN Phase Transition, Lattice Parameters of AN-KN, X-ray Diffraction The lattice parameters of the low and high temperature phase of KNO3-rich (in NH4NO3) solid solutions have been determined by the X-ray diffraction method. The low temperature single KNO3 phase (KN II) are from 92%-100% KNO3 in NH4NO3 composition range and from room temperature to 393 K showing in X-ray diffraction patterns. The high temperature KNO3 phase (KN I) showed very broad composition range between 20% to 100% KNO3. The lattice parameters of KNO3-rich (KN II and KN I) solid solutions have been calculated at different temperature range. The volumes of orthorhombic KN II phase decrease from 0.3208(3) to 0.3195(3) nm³ at the room temperature as the compositions increase from 95% to 100% KNO3. The lattice constants of the hexagonal KN I phase show that there is no significant change in a-direction when the temperature increases. Details X-ray results and lattice expansion equations during heating will be presented.

Jan 1, 2005

By David B. George

In spite of the many well-known problems inherent in Pierce-Smith converting, it remains the dominant copper converting process. Continuous copper converting and direct concentrate to blister smelting have been commercially available for over 25 years and now produce approximately 15% of copper smelter production. The two fully commercialized continuous converting processes, Mitsubishi MI Process and Kennecott-Outokumpu Flash Converting, and several emerging converting processes are reviewed with view of their potential, limitations, and environmental performance. Some myths regarding these technologies and Peirce-Smith converting are also challenged.

Jan 1, 2002

By Atinuke Oladoye, David Esezobor

"Particulate Copper Silicon carbide (Cu-SiCp) composites find application as wear and heat resistant materials in electrical sliding contacts such as in homopolar machines, railway overhead current collector systems where high electrical/thermal conductivity combined with good wear properties is required. However, challenges occur during machining due to the presence of hard reinforcement in the matrix. This may lead to high turnover of tool wear and poor surface finish. The adoption of near-net shape technology to produce such hard-to-machine metal matrix composites and subsequent finish machining with its attendant cost has reported limited success. This paper critically appraises the challenges and opportunities in the improvement of tribological characteristics of particulate Cu-SiC composites and identifies low cost reinforcement material that could be used to improve its tribological characteristics.IntroductionTribology consideration is increasingly becoming a decisive factor in the design and selection of materials for applications involving interacting surfaces in relative motion. The consideration is mainly on the combined effects of friction and lubrication on material's wear integrity and performance amongst other. Annual losses due to tribology in the US industries are estimated at between 1-2% of the Gross National Income [1], in Russia it is about 1-4% of the GDP [2]. Thus, the attributes of tribology has become imperative in modem machinery especially those applications involving sliding and rolling surfaces, and electrical contacts [3- 8].These are readily found in homopolar machines, internal combustion engines, aircraft engines, gears, cams, seals and railway overhead current collector systems [9-12]. In these systems, the dissipation of frictional heat arising from the interacting surfaces as quickly as possible imposes constraints on the choice of materials for such application to prevent softening, plastic and shear flow and the transfer of metal as wear debris onto the interacting surfaces. If these possibilities occur, system performance is compromised and premature failure may result. Materials for these systems are expected to possess high electrical and thermal conductivities, low coefficient of thermal expansion, good corrosion resistance and high melting point [3-8, 13]."

Jan 1, 2011

By M. R. Barkhudarov

Semi-solid metal can be formed into useful products of near net shape and high quality. Use of this method has been limited, however, because of the difficulty of working with metal in the semi-solid state, which has strong shear rate, temperature and time-dependent properties. In this paper we describe a thixotropic model and apply it to the problem of small metal droplets impacting on a flat plate.

Jan 1, 1997

By Marcelo B. Mourão

The reduction of iron ores by solid carbon, when both are agglomerated together in the form of pellets, has important kinetic advantages. Although several studies have been performed on the subject, some points on the controlling mechanisms need clarification. There is a big scatter in the values of the apparent activation energy reported in the literature, and this may be due to factors like heat transfer, flow of gases in the reduction system, pellet size and composition. This work is concerned with the effect of several parameters on the reaction rate. The parameters studied were temperature (in the range 1173 K to 1423 K), carbon type (coke or charcoal), pellet size, gas flow rate, catalyst action of the produced metallic iron and added sodium carbonate. It has been shown that the values of the apparent activation energy can change according to the reduction conditions employed, and hence any modeling effort will have to take account of these parameters. EPD Congress 1994

Jan 1, 1994

By Pengfu Tan

Lead blast-furnace bullion cools to near its freezing point in an operation known as copper drossing or hot drossing usually contains 0.02-0.06% copper. The removal of this copper is usually carried out in a batch operation known as sulfur drossing. Sulfur is stirred into the bullion at temperatures near its freezing point, and the dross of copper and lead sulfides that floats to the surface is skimmed off manually. A thermodynamic model has been developed to simulate the copper drossing. The phase diagram of Pb-Cu-S system has been calculated, and the effects of the process parameters, such as temperature, copper content, and sulfur content, on the drossing process have been simulated and discussed.

Jan 1, 2006

By Pratheesh George

Solid state galvanic cell with CaF2 as the electrolyte was employed for determining the thermodynamic properties of Nb-Al binary alloys in the temperature range of 973-1073 K. The activities and activity coefficients of Al in NbAl3 were determined. The experimental procedure and the design and construction of the experimental setup have been also explained in detail. Aluminum activity in NbAl3 increased with increase in temperature and shows a strong negative deviation from ideality. The activities of aluminum in NbAl3 were determined to be 0.0165 and 0.0289 at 973 and 1073 K respectively. The stability of NbAl3 has been compared with other available intermetallic systems.

Jan 1, 2006

By Kurt Westerlund

Three. years operating experience of the FLUXFLOW waste heat boiler (WHB) 20.000 nm /h at Boliden Ronnskar Sweden on a TBRC smelting palena (PbS). Operating experience from the Kivset flash WHB 11.900 nm /h at Samim, Porto Vesme, Sardinia, Italy. Conceptual features of the 93.600 nm3 /h FLUXFLOW (WHB) on the Isasmelt smelting in melt furnace for 180.000 t Cu/a at Mount Isa, Australia.

Jan 1, 1992