Search Documents

By C. T. Butler, W. W. Kay, R. D. Boddorff, R. L Ash

DRILLING and blasting in anthracite open-pit mines is a continuous problem to contractors and explosive engineers because of the diverse conditions caused by the nature of the geological formations, the extensive mining of the portions of coal beds near the surface, and the proximity of many strip pits to populated areas. Pennsylvania anthracite occurs in four separate long and narrow fields totaling only 480 sq miles. The coal measures are rock strata and coal beds that are considerably folded and faulted. The crests of the anticlines are eroded extensively. The beds outcrop on the mountain sides and dip under the valleys. At first only the upper portions of the syn-clines could be stripped. Now stripping to increasingly greater depths is economically possible, as is indicated by the fact that the proportion of freshly mined anthracite produced by strip mining has increased from 3.7 pct of the total tonnage in 1930 to 29.6 pct in 1950. Much of the rock overlying the deeper beds now being stripped is so extensively broken that considerable difficulty is experienced in drilling satisfactory blast holes and in using explosives in such manner as to insure a uniformly broken material easily removed by the excavating machinery. Such breaking of rock strata has occurred because the bed now being stripped has been mined extensively in former years by underground methods, and tops of gangways and chambers have subsequently failed. Draglines are used to uncover coal where the overburden can be moved with little or no re-handling. These machines range in size from those having a 2 cu yd capacity bucket on a 60-ft boom to those handling a 25 cu yd bucket on a 200-ft boom. Draglines are also used to strip to the bottom of the coal basins if the depth and the distance between the crops are not too great. For this type of operation blast holes are drilled full depth to the bed. These holes are commonly 30 to 90 ft deep; however, in exceptional cases, holes may be as shallow as 12 ft or as deep as 130 ft. Drilling is normally done for blasts of 12,000 to 60,000 cu yd of overburden, 30,000 cu yd being considered an average blast if vibration is not the controlling factor. Where the stripping of wide basins or the exposure of a moderately pitching vein makes the use of draglines impractical, dipper front shovels equipped with 4 to 6 cu yd buckets load into trucks. Overburden is removed in benches of 25 to 30 ft with blast holes drilled 4 or 5 ft deeper than the planned floor of the bench. For shovels under 5 cu yd bucket capacity the volume blasted varies from 8000 to 12,000 cu yd, whereas a volume of 30,000 to 50,000 cu yd of overburden is frequently blasted at one time for the larger shovels where vibration is not an important factor. During the past decade the churn drill, generally the Model 42-T Bucyrus-Erie blast hole drill equipped for drilling 9-in. diam holes, has become the most common blast hole drilling machine. Electricity powers half the churn drills in use and is preferred on the large strippings where electric shovels are operated and the working area is concentrated. On these operations the cost of additional electricity for the drills is less than the cost of fuel to operate diesel units because of the existing large demand load of the excavating equipment. Moreover, electric motors start more easily in cold weather and generally are less expensive to maintain. Diesel driven units are employed where a higher degree of mobility is required. The average drilling speed is 8 ft per hr, although in softer rocks a rate of 15 ft per hr is attained. Where rock is hard and strata is badly broken, drill speeds may be less than 2 ft per hr. Low drilling production results under these circumstances when loose material falling from the upper portion of the drill holes causes drill stems to be jammed. Rock formations vary so greatly in the region that a 9-in. diam churn drill bit may become dull after drilling only 2 ft or may drill satisfactorily for 56 ft; however, an average of 35 ft is usual in sandstone of medium hardness. Dull bits are hoisted to flat bed trucks by the sand line of the drill and are usually sharpened in the contractor's bit shop adjacent to the job. Care is generally taken to cover the thread end of the bit with a cap. To facilitate handling of bits around the drill, a heavy thread protector having an eye top is becoming more popular than the flat-top rubber or metal cap furnished with new bits. The 9-in. diam blast holes for a 25 to 30 ft bench are normally on 18x18 ft to 20x20 ft spacings, depending on the character of the overburden, although in broken ground 15x18 ft centers may be used to obtain better breakage and a more even bottom for the bench. The patterns of holes for shots

Jan 1, 1953

By R. D. Boddorff, R. L. Ash, C. T. Butler, W. W. Kay

DRILLING and blasting in anthracite open-pit mines is a continuous problem to contractors and explosive engineers because of the diverse conditions caused by the nature of the geological formations, the extensive mining of the portions of coal beds near the surface, and the proximity of many strip pits to populated areas. Pennsylvania anthracite occurs in four separate long and narrow fields totaling only 480 sq miles. The coal measures are rock strata and coal beds that are considerably folded and faulted. The crests of the anticlines are eroded extensively. The beds outcrop on the mountain sides and dip under the valleys. At first only the upper portions of the syn-clines could be stripped. Now stripping to increasingly greater depths is economically possible, as is indicated by the fact that the proportion of freshly mined anthracite produced by strip mining has increased from 3.7 pct of the total tonnage in 1930 to 29.6 pct in 1950. Much of the rock overlying the deeper beds now being stripped is so extensively broken that considerable difficulty is experienced in drilling satisfactory blast holes and in using explosives in such manner as to insure a uniformly broken material easily removed by the excavating machinery. Such breaking of rock strata has occurred because the bed now being stripped has been mined extensively in former years by underground methods, and tops of gangways and chambers have subsequently failed. Draglines are used to uncover coal where the overburden can be moved with little or no re-handling. These machines range in size from those having a 2 cu yd capacity bucket on a 60-ft boom to those handling a 25 cu yd bucket on a 200-ft boom. Draglines are also used to strip to the bottom of the coal basins if the depth and the distance between the crops are not too great. For this type of operation blast holes are drilled full depth to the bed. These holes are commonly 30 to 90 ft deep; however, in exceptional cases, holes may be as shallow as 12 ft or as deep as 130 ft. Drilling is normally done for blasts of 12,000 to 60,000 cu yd of overburden, 30,000 cu yd being considered an average blast if vibration is not the controlling factor. Where the stripping of wide basins or the exposure of a moderately pitching vein makes the use of draglines impractical, dipper front shovels equipped with 4 to 6 cu yd buckets load into trucks. Overburden is removed in benches of 25 to 30 ft with blast holes drilled 4 or 5 ft deeper than the planned floor of the bench. For shovels under 5 cu yd bucket capacity the volume blasted varies from 8000 to 12,000 cu yd, whereas a volume of 30,000 to 50,000 cu yd of overburden is frequently blasted at one time for the larger shovels where vibration is not an important factor. During the past decade the churn drill, generally the Model 42-T Bucyrus-Erie blast hole drill equipped for drilling 9-in. diam holes, has become the most common blast hole drilling machine. Electricity powers half the churn drills in use and is preferred on the large strippings where electric shovels are operated and the working area is concentrated. On these operations the cost of additional electricity for the drills is less than the cost of fuel to operate diesel units because of the existing large demand load of the excavating equipment. Moreover, electric motors start more easily in cold weather and generally are less expensive to maintain. Diesel driven units are employed where a higher degree of mobility is required. The average drilling speed is 8 ft per hr, although in softer rocks a rate of 15 ft per hr is attained. Where rock is hard and strata is badly broken, drill speeds may be less than 2 ft per hr. Low drilling production results under these circumstances when loose material falling from the upper portion of the drill holes causes drill stems to be jammed. Rock formations vary so greatly in the region that a 9-in. diam churn drill bit may become dull after drilling only 2 ft or may drill satisfactorily for 56 ft; however, an average of 35 ft is usual in sandstone of medium hardness. Dull bits are hoisted to flat bed trucks by the sand line of the drill and are usually sharpened in the contractor's bit shop adjacent to the job. Care is generally taken to cover the thread end of the bit with a cap. To facilitate handling of bits around the drill, a heavy thread protector having an eye top is becoming more popular than the flat-top rubber or metal cap furnished with new bits. The 9-in. diam blast holes for a 25 to 30 ft bench are normally on 18x18 ft to 20x20 ft spacings, depending on the character of the overburden, although in broken ground 15x18 ft centers may be used to obtain better breakage and a more even bottom for the bench. The patterns of holes for shots

Jan 1, 1953

By E. V. Potter, E. T. Hayes, H. C. Lukens

LARGE volumes of hydrogen are liberated at the cathode during electrolytic precipitation of manganese. Most of the gas escapes from the electrolyte, but a considerable amount may be entrapped in the manganese plate. Gas has been observed to escape from manganese melts in puffs that ignite at the surface. It has been reported that castings made with electrolytic manganese tend to rise in the molds; for this reason the manganese is often treated to remove hydrogen before the melt is made or it is premelted and used as cast manganese in making the alloys. The effect of hydrogen on the properties of manganese and its alloys is not known, but its effect on iron and iron alloys has been studied extensively.1.2 The close relationship between iron and man¬ganese suggests that hydrogen may have a similar effect on the properties of manganese and its alloys. The purpose of this investigation was to determine the amount of hydrogen or other gases in typical commercial electrolytic manganese sheet and to investigate ways of removing it most conveniently. APPARATUS The apparatus used is shown schematically in Fig. I. It consists of a chamber A in which the metal sample is placed, a vacuum or pressure gauge B, volume gauge C, vacuum pump D, hydrogen container E, auxiliary gas chamber F, and furnace G. The specimen chamber was made of two concentric quartz tubes. The outer one, a, connects with the closed gas system and is surrounded by the furnace G. A second tube, b, fits closely inside a and has a small end that projects into the space for the specimen and holds the thermocouple for measuring the temperature of the sample. The inner tube is joined to the outer tube outside the furnace, with rubber tape and sealing wax, to prevent gas leakage into or out of the closed system. This type of specimen container is loaded very easily and can be used several times if molten metal does not come in contact with the quartz. An ordinary mercury manometer B is used to measure the pressure in the system. The volume gauge C is essentially another mercury manometer, but the volume of the column is much larger than normal and the height of the mercury can be varied by raising or lowering the well H. In this apparatus the tube had a volume of I00 c.c. for a 60-cm. length. For larger changes in gas volumes; auxiliary containers F were used to increase the volume of the system by known amounts. Valves were arranged so that these auxiliary containers could be filled from the system and evacuated by the pump as often as necessary to accommodate the increases in the volume of gas in the system. The furnace G, used to heat the samples, was equipped with an automatic temperature controller, which maintained the desired temperatures within ± 5°C.

Jan 1, 1945

By Nelson P. Hulst

To those who have had the happy privilege of friendship with George W. Goetz, the announcement of his death has brought great sadness. He was born in Milwaukee, Wisconsin, February 17, 1855, and died January 15, 1897. In his boyhood days, when I first came to know him, his frank, trustful manner; his eyes brimming with truthfulness; his eagerness, never obtrusive, to gain knowledge from all whom he met; and his equal readiness to give without ostentation of his store, constituted a personality which at once commanded confidence and won friendship. I am told that as a scholar of five years he was conspicuous for brightness, a show-pupil, who was called on to recite when visitors were present at school. Yet this in no way spoiled him. His modesty was too strong a trait in his character to be overcome by any attention which might, be expected to arouse vanity. In his simple-heartedness he was pleased then, as he always was in his maturer years, to give of his knowledge for the gratification of his listeners, with never a thought of himself. So strong was this characteristic that in a brief autobiography, in the form of a letter to his wife and children, found among his papers, he excuses himself to them for recounting what he had accomplished in his life-work. As a preface to this autobiography (which, it seems, was prepared on the eve of a sudden journey to California, taken February, 1895, for his health) he says: " I am writing this rather hastily, and I

Jan 1, 1898

By Theron Wasson

The discovery of eight new oil fields, two of which may be of major importance, was the outstanding record in Michigan this year. These new fields have helped to support the declining production from old areas and place the total of 18,559,000 bbl. in line with the past six or seven years. Thus, it appears that Michigan is doing its part in maintaining the production of the country in the third year of the war. The new fields are in the central basin area where oil was first discovered in Michigan, thus tending to focus attention on the deeper part of the lower peninsula of the state. Through 1944 the state of Michigan has produced a total of 222,-641,580 bbl. of crude oil from 100 pools, many of which arc relatively small. Among the previous1y discovered fields Reed City is still the outstanding producer, with Fork, Headquarters, and Adams following in the order named. The Reed City pool produced a little over 5,000,00 bbl., which was more than one third of the state's total for the year. Almost two thirds of the year's total oil production came from fields discovered in the past five years. Maps A map of the oil and gas fields of Michigan in 1943, published in the A.I.M.E. report for 1944,* shows the main producing areas and should be referred to if information in regard to their location is desired. The producing zones are shown in the columnar section in the same publi- cation." The data in Tables I and 2 have been carefully ' checked and every effort has been made to show as complcte information as possible. New Discoveries and New Developments Eight new producing areas were discovered during 1944 which, in order of importance, are: Deep River Field.—The discovery well in the Deep River field was drilled by Don Rayburn and others, and should be listed as a chance discovery, as, from a geological standpoint, it was not considered favorable until oil was found at a depth of 2838 ft. in a dolomitic layer in the top of the Dundee limestone. The first well was completed in January 1944, with an initial production of 2500 bbl. By the end of the year 15 wells had been completed, proying an area 2 1/2 miles long and 1/2 mile wide. Coldttater Field.-The Coldwater field was discovered in August 1944, by the Sohio Oil Co. Production is from secondary dolomite at the top of the Dundee at a depth of 3703 ft. To the end of 1944 nine wells had been drilled on 40-acre spacing. Essexville Field.—Essexville field was discovered by United Drillers and Producers, Inc. Eight wells had been completed to the Dundee lime by the end of 1944, and prospects were good for further development during 1945. Hilliards Field.—Hilliards field was discovered by Cook and Fortney. Production is from the Traverse lime at an average depth of 1588 feet,

Jan 1, 1945

By Richard Pearce

In the treatment of auriferous copper containing bismuth, I have recently observed a small quantity of a grayish-white alloy, which on examination, proved to be Bi containing in solution, as it were, a crystalline alloy of Bi and Au. This compound makes its appearance on the surface of the auriferous Cu in small globules as the latter cools. These globules are rapidly attacked by nitric acid, and fine needleshaped crystals of Bi and Au separate out. They arc insoluble even in strong nitric acid. On examination, the crystals mere found to contain : Gold, 69.94 per cent.; silver, 0.63 per cent. ; bismuth, 29.43 per cent. (No. I).* The residue is very fusible, and at a temperature considerably below its melting-point it oxidizes rapidly, changing from its original gray color to a greenish-yellow (No. 2). On melting in a crucible under flux, a bronze-colored alloy is formed that has the specific gravity 15.47—somewhat higher than the calculated specific gravity of a simple mixture of the two metals in the proportions named. Alloys of Gold and Silver.—In following out my investigations by repeated examinations of this alloy formed at different times, I found that, in dissolving a miscellaneous lot of the alloy in nitric acid, some gold-yellow crystals were formed, which I succeeded in separating from the BiAu alloy by washing. These yellow crystals, under the microscope, showed distinct, regular, octahedral faces, and on examination they were found to be a crystalline alloy of Au and

Jan 1, 1885

By R. E. Frounfelker, W. M. Hirthe

INVESTIGATORS in the areas of plasticity, crystal growth, and stress analysis have a need for crys-tallographic data such as the interplanar angles. This information is utilized in the form of a stereo-graphic projection from which orientation determinations can be made. Calculations of mechanical properties, such as the critical resolved shear stress, require values for the angles between directions as well as the interplanar angles. Only a limited amount of this data is available for tetragonal crystals. The equations for these angles are relatively simple but because of the large numbers of angles involved and the infinite number of structures that could be investigated, it was decided to program these calculations on a high speed digital computer. The angle, 8, between two crystal planes (h1 k1 l1)

Jan 1, 1962

Albin, B. R Billings, Mont. '28 Amster, Nathan L 25 Broad St., New York, N. Y. '28 Bache, Jules S 42 Broadway, New York, N. Y. '28 Barrett, C. P 5338 Harper Ave., Chicago, 111. '28 Bayless, William S Russ Bldg., San Francisco, Cal. '28 Bean, Louis, H 60 E. 42nd St., New York, N. Y. '28 Beatty, Ross J Room 604, 6 N. Clark St., Chicago, III. '28 Benwell, Oswald F Hold Mags. '28 Beymer, Albert S., V.P., Keystone National Bank Pittsburgh, Pa. '28 Blumenthal, Hugo 44 Pine St., New York, N. Y. '28 Boettcher. Charles Ideal Cement Bldg., Denver, Colo. '28 Bowlus, Thomas H., Banker, Pres., Allen County State Bank Iola, Ran. '28 Brown, Colvin B Chamber of Commerce, Washington, D. C. '28 Burt, Maxwell Struthers Southern Pines, N. C. '28

Jan 1, 1936

By John F. Blandy

The map on Plate I illustrates a part of the works of the Red Bank Mining Company, on the Upper Freeport seam of coal, in Armstrong County, Pennsylvania. The contour lines give a careful representation of the conformation of the surface, showing also the line of outcrop of the seam, and the gangways of the mines are shown by the black lines. Upon assuming charge of the works in January last, I found that the first and greatest difficulty lay in the great uncertainty of the

By F. W. Bryan, D. H. Lynch

Introduction This paper is a general description of current central Florida phosphate mining, beneficiation, and product transportation. It is directed and believed to be of interest to engineers not familiar with this industry. Deposit: The phosphate deposits of central Florida are generally located in a five county area which includes Polk, Hillsborough, Hardee, Manatee, and DeSota counties. Geologically, the deposit is of marine origin and is identified as the Bone Valley formation. This formation is Pliocene to Recent in geological age and overlies a Miocene limestone formation known as the Hawthorn. The Bone Valley formation sediments are regionally characterized by equal proportions of apatite, quartz, and clay. The clay is predominantly of the mont-morillonite family. On a local scale, however, the proportions of these three major constituents vary considerably. The phosphate occurs as the apatite mineral (Ca 10F2(PO4)(6) and with the clay and sand, the minable ore is commonly referred to as matrix. This matrix is overlain by unconsolidated overburden of sand and sandy clays, ranging in depth from 10 to 45 ft. The matrix usually occurs in fairly horizontal continuous beds from 3 to 25 ft in thickness. The bedded limestone formation lies directly below the matrix and is generally well defined. The phosphate particles range from 3/4 in. to 200 mesh (Tyler) in size. The phosphate particles coarser than 14 mesh are called pebble phosphate and those less than 14 mesh are termed flotation feed which, when beneficiated, subsequently become concentrates. Through mining and beneficiation, phosphate quality is measured in BPL percent which stands for bone phosphate of lime units. In subsequent chemical manufacturing, the quality is indicated by P205 content. The deposit is economically characterized by various ratios such as tons of product per acre and cubic yards handled per ton of product. Magnesium, iron, and aluminum content are also considered in evaluating ore reserves. These elements are often critical to the chemical fertilizer processes. Presently, an ore body is considered economically minable if it meets the criteria shown in [Table 1]. These, of course, are general guidelines and specific costs and returns on investment must be considered in each case for acquiring reserves. On a new grass-root venture, a 20-30 year life is generally expected with a mineral recovery of 80%. History and Uses Phosphate mining in central Florida began around the turn of the century. However, in the early days, only pebble phosphate was produced until about 1930 when technology was available to beneficiate the -14 + 150 mesh particles. The -150 or -200 mesh material was discarded as it is today. The basic processes for beneficiation are washing, scrubbing, desliming, sizing, and flotation. These basic unit processes are essentially the same today although many improvements have been developed since the early days. Phosphate is used primarily in the production of high analysis fertilizer chemicals, typical of which are triple superphosphate, monoammonium phosphate (MAP), and diammonium phosphate (DAP). Phosphate is also used in the production of food preservatives, dyes for cloths, vitamin and mineral capsules, steel hardeners, gasoline and oil additives, toothpaste, shaving creams and soaps, bone china dishes, plastics, optical glass, photographic films, light filaments, water softeners, insecticides, soft drinks, road fill, and livestock feed supplements. Florida produces over 80% of the nation's marketable phosphate rock and one-third of the world production, according to the US Bureau of Mines. This amounted to approximately 35 million tons in 1975. Exports of Florida phosphate rock were to such countries as Canada, Japan, West Germany, Italy, and India, with Canada and Japan being the major users. Almost 95 o of all outbound cargo shipped through the port of Tampa is phosphate rock or related products. Beneficiation Following is a description of Agrico's new Fort Green beneficiation plant which is typical of the newer large capacity plants being built in the field. Agrico's Fort Green mine was completed in 1975 and is located in the southwest corner of Polk County and is directly adjacent to Manatee, Hillsborough, and Hardee Counties. With some minor differences, Fort Green is typical of a modern central Florida plant. The rated capacity is 3,000,000 plus tons of product per year and this varies according to the richness of the ore being handled. A simplified flowsheet is presented in [Figs.1 and 2]. This plant is served by three draglines of the 40-cu-yd class. The phosphate beneficiation is usually divided into three major functional steps: (1) washing and screening to produce a pebble product and flotation feed, (2) feed preparation and (3) flotation to produce concentrates. The typical plant is similarly divided into these three functional areas. Washer: Briefly, the slurried matrix is pumped from two draglines simultaneously at a combined rate of about 20,000 gpm at 2000 tph (solids) to rotary trommel screens sized to make a 7/8-in. separation. ([See Fig. 1]-) The trommel oversize is sent to hammermills where it is crushed and returned to the trommel screens, or pumped to tailings if minor impurities (Fe203, A1203, MgO) are too high. The trommel undersize is pumped to 14 mesh stationary (static) flat screens. The flat screen over¬size is subjected to three stages of 14 mesh vibrating screening and two stages of log washing in order to produce a final pebble product. The pebble product (+ 14 mesh material) is conveyed by belt conveyor to a large on-ground storage pile. Pebble product is reclaimed through a tunnel and loading system below

Jan 1, 1980

By Theodore B. Comstock

The paper of Mr. S. F. Emmons on the structural relations of ore-deposits, presented at the Boston meeting in February last, having been, as I am informed, unavoidably delayed in publication, was not distributed in the preliminary edition to members until immediately before the sheets of Volume XVI. of the Transactions, containing it, were sent to press. Consequently, I saw it for the first time too late to offer any comments which might have accompanied it in that volume. This is my justification for present-

Jan 1, 1889

By Winston A. Wong, John J. Jonas

Commercial purity aluminum was deformed by extrusion over the temperature range 320° to 616°C and the strain rate range 0.1 to 10 per sec. Flow stresses and strain rates were calculated from the experimenLa1 ram pressures and speeds. The stress-strain rate-lemperature relationship in extrusion was found to be similar to that in creep. Extrusion, torsion, compression, and creep data extending over ten orders of magnitude of strain rate and over two orders of magnitude of stress were correlated by a single creep equation. It was concluded that hot-working is a thermally activated process, in which the rate-controlling mechanism is either the climb of edge dislocations or [he motion of jogged screw dislocations. The microstructural changes observed during extrusion were consistent with the proposed deformation mechanisms. ALTHOUGH great progress has been made in understanding the technology of extrusion, very little is known about the actual deformation mechanisms operating during flow. Previous accounts describing extrusion have indicated that the relationship between ram speed (V), pressure (P), and temperature (T) can be given as follows:1 V = apb and P = A' exp(-AT). In these equations, a and b are constants which depend on temperature, A' is a constant which depends on ram speed, and A is a "coefficient" with a different value for each metal. Although these equations have fairly wide application, they do not contribute much to a fundamental understanding of the deformation. Furthermore, extrusion has not hitherto been considered as a thermally activated rate process. This lacuna is surprising because hot-working is similar to high-temperature creep in several respects. There is, in fact, a fair body of experimental evidence suggesting that the material response under hot-working conditions is similar to that occurring under creep conditions, in spite of the many orders of magnitude difference in strain rate.2"4 Since creep has been extensively analyzed in terms of dislocation mechanisms, the comparison of hot-working to creep is useful, for it can suggest the possible deformation mechanisms operating during hot-working. In this paper, the hot extrusion of aluminum will be examined from the point of view of thermally activated deformation mechanisms, such as operate during creep. EXPERIMENTAL PROCEDURE The experimental procedure consisted of extruding commercial purity aluminum* over a range of ram velocities and temperatures at constant die reduction by the direct method. Details of the experimental equipment have been published elsewhere.5 Extrusion was carried out at each of the following billet temperatures: 320°, 376°, 445°, 490°, 555°, and 616°C at the following constant ram speeds: 0.002, 0.008, 0.02, 0.1, and 0.2 in. per sec.* All results were obtained using a square-shouldered die with an extrusion ratio of 40:1, giving a reduction in area of 97.5 pct. The ram force was the dependent variable, and was measured by means of strain gages on the ram and was plotted as a function of ram travel. The sequence of events before making an extrusion was duplicated before each run so as to minimize as much as possible variations in experimental conditions. For example, after the equipment had been assembled, the billet was allowed to heat up to temperature inside the insulated container. Once the container attained the desired temperature, a period of 1/2 hr was allowed to elapse before the extrusion was made. This time was found to be required to allow the billet to reach a steady-state temperature, as determined from previous tests. When all was ready, extrusion was carried out without interruption; that is, the billet was upset and extruded in one operation. EXPERIMENTAL RESULTS AND DISCUSSION The two usual experimental approaches for investigating high-temperature deformation exhibit an important common feature. In the first approach, which corresponds to creep, a constant stress (or load) is applied to the material at constant temperature and the resultant strain is recorded against time. After an initial transient stage, a state of constant strain rate exists (secondary creep), in which a steady-state condition is established which is sensitive to variation in either applied stress or temperature. In the second approach, a constant strain rate is applied and the resultant flow stress is recorded. This corresponds to the situation in hot torsion or hot compression, where it is observed that, for a constant test temperature, there is an initial rise in stress to a steady value which is maintained up to very high strains. In tests of this type, a steady-state region is also established in which the stress is sensitive to variation in either the strain rate or the temperature.3,4,6-16 In both types of tests, therefore, a steady-state region is established after an initial transient. In the case of hot-working this region may be called steady-state hot-working, and it is analogous to steady-state creep with which it has many common features. Stress Dependence of the strain Rate in Extrusion. In order to assess the stress dependence of the strain rate under extrusion conditions, and to compare it to that of creep, as well as of hot torsion and hot compression, the extrusion data were analyzed according to power, exponential and hyperbolic sine creep equations.

Jan 1, 1969

By Frederick Vickery

THE discovery of oil on the Goleta anticline has extended the petroliferous areas of California 18 miles west of the previous limit at Summerland and 35 miles south of the fields at Santa Maria. In each of these localities the oil is found in the Miocene-Pliocene strata, but as the oil at Goleta is found in the Sespe formation, which is generally considered as Oligocene or lowermost Miocene, the Goleta field extends the production of that horizon 52 miles west of South Mountain, the previous western outpost. Two horizons of high-gravity, paraffin-base oil have been found at shallow depths, and the exploratory well, Goleta No. 1, is now being drilled to test the productivity of an expected horizon in the Meganos formation. The Goleta structure is 12 miles west of the city of Santa Barbara and 2 miles north of the coast. Although it is within part of the old Spanish Rancho, Los Pueblos, it corresponds to T. 4 N., R. 29 W., S. B. B. and M., Santa Barbara county, California. The discovery well, Goleta No. 1 was drilled by the Miley Petroleum Ex-ploration Co. on the Tecolote ranch in the part of the Spanish grant corresponding to the sw. 1/4 of the nw. 1/4 of Section 3. Despite the apparent isolated position of the Goleta field, it is within the Ventura basin. The idea that the Ventura basin terminates at the ocean beach near the city of Ventura is neither sup-ported by the geologic structures nor the sequence of strata west of that city. This basin at the present time is known on the land as the Santa Clara valley and beneath the sea as the Santa Barbara channel. It extends westward to Point Concepcion. The Ventura basin, before the Miocene and Pliocene epochs of deformation, was much broader than at the present time. It is bounded by two lines of uplift, the Santa Ynez range on the north and the Santa Monica mountains with their extension, the Channel islands, on the south. Both of these ranges trend east and west. The Ventura basin and the mountains that bound it are part of a remark-able east-west orogenic unit, which interrupts the pre-vailingly northwest ranges along the Pacific Coast.

Jan 10, 1927

By R. D. Boddorff, R. L. Ash, C. T. Butler, W. W. Kay

DRILLING and blasting in anthracite open-pit mines is a continuous problem to contractors and explosive engineers because of the diverse conditions caused by the nature of the geological formations, the extensive mining of the portions of coal beds near the surface, and the proximity of many strip pits to populated areas. Pennsylvania anthracite occurs in four separate long and narrow fields totaling only 480 sq miles. The coal measures are rock strata and coal beds that are considerably folded and faulted. The crests of the anticlines are eroded extensively. The beds outcrop on the mountain sides and dip under the valleys. At first only the upper portions of the synclines could be stripped. Now stripping to increasingly greater depths is economically possible, as is indicated by the fact that the proportion of freshly mined anthracite produced by strip mining has increased from 3.7 pct of the total tonnage in 1930 to 29.6 pct in 1950. Much of the rock overlying the deeper beds now being stripped is so extensively broken that considerable difficulty is experienced in drilling satisfactory blast holes and in using explosives in such manner as to insure a uniformly broken material easily removed by the excavating machinery. Such breaking of rock strata has occurred because the bed now being stripped has been mined extensively in former years by underground methods, and tops of gangways and chambers have subsequently failed. Draglines are used to uncover coal where the overburden can be moved with little or no rehandling. These machines range in size from those having a 2 cu yd capacity bucket on a 60-ft boom to those handling a 25 cu yd bucket on a 200-ft boom. Draglines are also used to strip to the bottom of the coal basins if the depth and the distance between the crops are not too great. For this type of operation blast holes are drilled full depth to the bed. These holes are commonly 30 to 90 ft deep; however, in exceptional cases, holes may be as shallow as 12 ft or as deep as 130 ft. Drilling is normally done for blasts of 12,000 to 60,000 cu yd of overburden, 30,000 cu yd being considered an average blast if vibration is not the controlling factor. Where the stripping of wide basins or the exposure of a moderately pitching vein makes the use of draglines impractical, dipper front shovels equipped with 4 to 6 1/2 cu yd buckets load into trucks. Overburden is removed in benches of 25 to 30 ft with blast holes drilled 4 or 5 ft deeper than the planned floor of the bench. For shovels under 5 cu yd bucket capacity the volume blasted varies from 8000 to 12,000 cu yd, whereas a volume of 30,000 to 50,000 cu yd of overburden is frequently blasted at one time for the larger shovels where vibration is not an important factor. During the past decade the churn drill, generally the Model 42-T Bucyrus-Erie blast hole drill equipped for drilling 9-in. diam holes, has become the most common blast hole drilling machine. Electricity powers half the churn drills in use and is preferred on the large strippings where electric shovels are operated and the working area is concentrated. On these operations the cost of additional electricity for the drills is less than the cost of fuel to operate diesel units because of the existing large demand load of the excavating equipment. Moreover, electric motors start more easily in cold weather and generally are less expensive to maintain. Diesel driven units are employed where a higher degree of mobility. is required. The average drilling speed is 8 ft per hr, although in softer rocks a rate of 15 ft per hr is attained. Where rock is hard and strata is badly broken, drill speeds may ' be less than 2 ft per hr. Low drilling production results under these circumstances when loose material falling from the upper portion of the drill holes causes drill stems to be jammed. Rock formations vary so greatly in the region that a 9-in. diam churn drill bit may become dull after drilling only 2 ft or may drill satisfactorily for 56 ft; however, an average of 35 ft is usual in sandstone of medium hardness. Dull bits are hoisted to flat bed trucks by the sand line of the drill and are usually sharpened in the contractor's bit shop adjacent to the job. Care is generally taken to cover the thread end of the bit with a cap. To facilitate handling of bits around the drill, a heavy thread protector having an eye top is becoming more popular than the flat-top rubber or metal cap furnished with new bits. The 9-in. diam blast holes for a 25 to 30 ft bench are normally on 18x18 ft to 20x20 ft spacings, depending on the character of the overburden, although in broken ground 15x18 ft centers may be used to obtain better breakage and a more even bottom for the bench. The patterns of holes for shots

Jan 1, 1952

By L. W. Pommier, L. R. Plitt, F. B. Brien

L. R. Plitt (Assistant Professor of Mining and Metallurgy, University of Alberta, Canada.) — It is indeed encouraging to see rheological studies being carried out in a mineral engineering school. The bulk of the work being done today in applied rheology seems to be concerned with the behavior of polymeric solutions and thus has limited application to the solid-liquid systems encountered in mineral beneficiation. The authors have approached the problem by carrying out a dimensional analysis which showed that for power law fluids the drag coefficient, Ds, must be some function of a generalized Reynolds number which has the form: If the power law adequately describes the behavior of a fluid, the dimensional analyses predicts that the Ds - RN function should hold for all values of n' or any other dependent variable. The experimental evi-

Jan 1, 1968

By Jr. Baldwin. William M

WELL known to every metallurgist is the fact that different production schedules will profoundly affect the character of annealed metal strip. Yet the number of conditions [ ] that may be wrought by different combinations of rolling and annealing schedules is so myriad that despite the continual research that is being applied to this subject, the complete picture is not yet known. Copper, like all other metals, during the process of rolling or annealing, develops certain crystallographic configurations which should not be dismissed as being too impractical, for the crystallographic condition existing within the metal is a principal influence upon both the external mechanical properties and the behavior of the material [ ] when it is subjected to such operations as bending, flanging, drawing, and so forth. EFFECT OF ROLLING AND ANNEALING UPON THE CRYSTALLOGRAPHY OF COPPER STRIP The most salient points in the crystallographic reactions of polycrystalline copper to rolling and annealing may be best represented graphically by a "map" such as that given in Fig. I. I. As copper strip is cold-rolled from a randomly oriented structure (pole figure I),

Jan 1, 1942

By Freeman Bishop

Senator Henry M. Jackson t D. Wash.) recently tossed a live grenade into the hardrock mining industry with proposed legislation to change provisions of the law governing Federally owned mineral values. Title Two of the measure would place hardrock mining agreements on a leasing basis similar to that which has applied to oil and gas since 1920. Known as the "Public Domain Lands Organic Act 01 1971" or S.921, the bill would monitor exploration by heavy machinery which ran destroy fragile ecology without any requirement for restoration or rehabilitation." Jackson said. Abandoned mining claims, lie continued, dot the public domain, "casting clouds upon the title to property which belongs to all the people.” and a minerals leasing system is "the most practical way of achieving the proper balance."

Jan 1, 1971

By S. D. Michaelson

[CONTENTS PACE See TP 2377, Min. Tech, May 1948 for discussion of A Technique for Photographing Difficult Subjects through a Petrographic Microscope (TP 2092 by DONALD W. SCOTT, Min. Tech., Nov. 1946. Discussion by HORACE WINCHELL). Metallurgical Efficiency-a Yardstick in Lead-zinc Flotation Metallurgy (TP 2141 by R. A. ....... PALLANCH, Min. Tech:, March 1947. Discussion by S. D. MICHAELSON). I Symposium on Milling Devices and Practices. (TP 2162 by J. F. MYERS and R. J. TOWER, Min. Tech., May 1947. Discussion by HARLOWE HARDINGE). ............ 2 Rod Milling-Plant and Laboratory Data. (TP 2175 by J. F. MYERS, S. D. MICHAELSON and F. C. BOND, Min. Tech., July 1947. Authors' supplement and discussion by HARLOWE .......................... HARDINGE, and B. H. IRWIN) 2 A New Separating Vessel for Sink-float Concentration. (TP 2182 by E. C. BITZER, Min. Tech., May 1947. Discussion by E. H. CRABTREE, JR.) .................. 5] Metallurgical Efficiency-a Yardstick in Lead-zinc Flotation Metallurgy S. D, MICHAELSON*-The method of determining the efficacy of a separation described in this paper, gives the metallurgist a most useful guide for keeping his ship on an even keel When the ore Waves vary from placid seas to high breakers. Now that such a method of evaluating metallurgical efficiency has been developed and proven practical, it Would seem logical to introduce the next, and more final, factor of Economic Efficiency. I choose to define this term as the percentage ratio of net return from milling to the theoretical maximum net return. The actual operating cost subtracted from the actual mill return represents the net actual amount received for the material treated. Experienced operators of most plants Would ordinarily have enough data on hand to estimate a theoretical milling cost per ton, based on labor, power, supplies and maintenance When operating at maximum tonnage With minimum trouble and under ideal ore conditions. When this theoretical estimated cost is subtracted from the theoretical maximum ore return (calculated by Pallanch's method) the resulting figure is the maximum theoretical net amount the mill operator could hope to realize in processing the ore. The percentage ratio of these sums, of actual to theoretical, is the economic efficiency of the operations. This economic efficiency, if determined on the basis of a fixed market price for metal and similarly fixed base rates for labor, power and supplies, Will reflect the effect of changes in milling practice, labor efficiency and equipment condition. When computations made on the basis of actual current rates for labor, power and supplies are compared With similar actual figures for past periods they will show forcefully how energetic our hunt must be to develop man saving controls, more effective metallurgy, and better equipment to maintain profitable operations. Such computations also offer a simple means of determining how much more labor, supplies and power can be put into the mill operation to obtain an increase in metallurgical recovery at a profit.

Jan 1, 1947

By Hsun Hu

C. G. Dunn (Geneva1 Electvic Reseavclz Labo,vatory)-Dr. Hu16 has obtained a number of rolling and annealing texture results that partly agree with those of Dunn17 and Dunn and Kohl8 for experiments of a similar nature. I would like to discuss some of the points of agreement as well as some of disagreement and then present some unpublished data as a contribution to the work on textures. Firstly, there is agreement on the components produced during a 70 pct cold-rolling reduction of a (110) [001 ] single crystal; there is agreement on the forma- tion of a (110) [001] recrystallization texture provided recrystallization occurs at 800°C or higher; and there is agreement on the formation of (120) [001] components provided recrystallization occurs below 600°C. There is some disagreement on the low-temperature recrystallization since I also obtained a substantial amount of a (110) [001] component while the author obtained only (120) [001] components. I also discussed the differences between low- and high-temperature recrystallization (which included further annealing changes in the samples on long

Jan 1, 1962

A GIFT of $10,000 to the endowment of Engineering Foun-dation, made by the Central Hudson Gas and Electric Corporation, has been announced. In transmitting this gift T. R. Beal, president of the corporation, made the follow-ing interesting statement: "You may be interested to know that this amount was in fact earned by our employees by their more efficient opera-tion of the physical properties under their care. It rep-resents $10,000 of return premiums paid during the past year on accident insurance, as the result of the company's excellent record in preceding years, so that we take greater satisfaction in making this gift as it is related, in some degree at least, to the higher standards of engineering and operating practice to which the work of the Foundation per-tains."

Jan 4, 1928