Search Documents

By T C. Souza Pinto, M Safari, F S. Hoseinian, D Deglon, L Leal Filhoc

In this study, the effect of hydrodynamic parameters on the iron ore reverse was investigated in a mechanical flotation cell. The work carries out using the case study of Iron ore from Vale in Brazil. The influence of hydrodynamic factors such as froth height, impeller speed, superficial gas velocity and solids percentage were evaluated on the quartz flotation. The results showed that the hydrodynamic conditions have a great effect on the flotation performance, especially on the fine and coarse quartz. The size-by-size analysis of the froth products showed that froth height, impeller speed, superficial gas velocity and solids percentage have a significant effect on true flotation quartz particles. The increase in the froth height decreased the recovery of quartz particles. The increase in the impeller speed increases the recovery of quartz particles to an optimum. The increase in the superficial gas velocity improved the flotation of coarse quartz particles. The increase in the solids percentage increases the recovery of quartz particles.

Sep 18, 2023

Blasting effectiveness must be gauged by total production costs. ANFO charges made up in polythene "sausages" are not as profitable as is indicated by the price of ANFO. All-slurry charges are warranted only where blastholes cannot be dewatered effectively, or where drilling costs are very high. An increase in blasthole diameter leads to coarser fragmentation. This effect is most pronounced in tough and massive or blocky strata, or in ground which consists of unfissured boulders in a softer matrix. When ANFO and some slurry-type charges of small diameter are used in plastic-acting ground, charges may fail to detonate through precompression by charges fired on an earlier delay. The optimum blasthole length is rarely less than four times the burden distance. For best results, blastholes should be inclined to the vertical and parallel to the face. Nominal burdens and spacings are often altered radically by the initiation sequence. For best fragmentation, all blastholes must have good effective faces, and should be effectively stagg- ered with an actual spacing:burden ratio in the approximate range 2.0-5.0.

Jan 1, 1975

By T Lancaster

The Mount Gordon operation, consisting of the Esperanza open cut mine and the unique Mount Gordon Ferric Leach processing plant, is operated by Western Metals Copper Ltd at Mount Gordon, 125 km north east of Mt Isa. The processing plant treats predominantly the secondary copper sulphide minerals, chalcocite and covellite. The gangue consists of massive pyrite and a range of silicified siltstones. The processing plant utilises a conventional single stage SAG/cyclone milling circuit, followed by low-temperature/low-pressure autoclave oxidation to produce copper in solution. The pregnant leach solution is treated via conventional SX/EW technology to produce copper cathode. Currently the plant is operating at a nominal production rate of 48 500 tpa copper. The Mount Gordon Ferric Leach technology is the worlds first integrated pressure leach/SX/EW process to be used to treat copper sulphides on a full plant scale. In the last six months, July to December 2001, the plant has emerged from a two-year postcommissioning phase to achieve steady state operation. This has been characterised by high plant availability and consistent production performance in excess of the name plate capacity of 45 000 tonnes. Production rates will continue to increase over the next 12 months to over 50 000 tpa via a planned process of incremental improvements. The pressure leach circuit has consistently achieved availabilities exceeding 95 per cent over the past 18 months. Notwithstanding this, the leach circuit still has a much greater requirement for planned maintenance than SX/EW. For much of the Mount Gordon processing plantÆs operating life, the leaching process has constrained production. Recent developments arising from detailed mass and energy balance modelling have now significantly improved leach capability, resulting in the plant bottleneck being shifted to electrowinning. In order to balance the capabilities of the two circuits however, the surge capacity between leach and SX/EW was increased substantially. This effectively de-coupled the higher capability but lower availability leach circuit from the lower capability but higher availability SX/EW circuit. As a result, electrowinning utilisation has increased to in excess of 98 per cent, which is reflected in a higher overall plant throughput.

Jan 1, 2002

Compared with modern longwall coal mining systems, automation has not been developed very far in the underground metal minin industry. One of the main reasons for this is that present har rock mining systems do not produce ore with a controlled degre of fragmentation. The often poor fragmentation from the stopescauses large extra costs and precludes material which 1-ends itself to automationThe paper investigates the possibility c technology for automatic loading and trapconveyor belt to a shaft dump pocket. With this concept, it will be necessary to control the maximum fragment size by careful blasting design. The degree of fragmentation will have to be finer than is common to-day. The study shows that the belt conveyor mining con-cept with controlled fragmentation may be economically competitive with conventional cyclic loading and transport, even for an annual production as low as 0.5 mill. tonnes.. Fragmentation design and cost calculations have been based on a combination of the Kuznetsov relationship between blasting parameters and mean frag-ment size, and the Rosin-Rammler formula for fragment size distribution.

Jan 1, 1985

By Cocker A, Kavetsky A

A numerical model describing blast fragmentation and damage in three dimensions has been developed at the Julius Kruuschnitt Mineral Research Centre (JKMRC) and applied to numerous blasting operations in mines throughout Australia. The model combines the rock structure (summarised by block size distribution) with blast strain energy and uses comminution theory to calculate the resultant block size distribution. The model distinguishes between rock breakage and failure, the former being defined as size reduction and the latter as block dissassembly. The background and basis of the model are discussed in detail and three case studies presented describing the application of the model to explosive performance evaluation, explosive selection and drill selection in Australian mining operations.

Jan 1, 1990

Autogenous and Semi-Autogenous grinding has become an accepted method of reducing primary crusher product to micron sizes in a single or a two-stage grinding circuit. The elimination of secondary and tertiary crusher circuits and sometimes rod mills helps to lower overall operating costs and, in many instances, can make uneconomical projects viable. Selecting AG/SAG Mills have been rather a "hit and miss" affair over the years, but now with the many different types of tests available, accurate mill size predictions can be made, provided the test data is evaluated correctly. This paper endeavours to simplify the process of evaluating test data and sets down some guidelines for designers to follow when selecting AG/SAG Mills.

Jan 1, 1991

By Kepplinger W

The COREX process is a technology for production of liquid hot metal on the basis of coal (without the use of a coking plant) developing by VOEST- ALPINE AG, Austria and its subsidiary company Korf Engineering GmbH, Federal Republic of Germany. CORED is a registered trademark of VOEST-ALPINE AG and Korf Engineering GmbH. The COREXW process is based on the idea of separating the process steps realized in the blast furnace (gene- ration of reduction gas, reduction of iron oxide and melting of the reduced iron) and including partial coking of the coal.

Jan 1, 1987

In May 1977 a new dam was commissioned for disposal of 600,000 metric tonnes/year of tailings. Design basis, costs and construction problems are described. Problems arose, assoc- iated with lack of experience in building such a dam "from scratch". Solutions are described land costs given.

Jan 1, 1978

By P Andersson, P Marklund

Evaluation of different techniques for bottom fill stabilisation showed that frozen fill was the most economical method. In order to test the method a full-scale field test was performed in the Rehnstr÷m mine. The test was instrumented with temperature gauges and extensometers. Before the field test, frozen fill was tested at the laboratory. The mechanical properties of the frozen fill were determined by uniaxial compression and creep tests. A deformation model for the frozen fill was set up. Calculation procedure for design of spacing between the freezing tubes, time for freezing and calculation of the necessary capacity of the refrigeration plant was developed. These procedures were calibrated against the field test. The results of these investigations allow the following conclusions: From a mechanical point of view, frozen fill has excellent properties as a structural member and it also has excellent properties to support itself and the fill above. Methods for the thermal and mechanical design of freeze stabilisation have been developed and found adequate. The need to place the freezing tubes several years in advance of the future sill pillar mining, requires careful long-term planning and accurate documentation.

Jan 1, 1998

The influence of strongly chemisorbed solutes such as oxygen and sulphur on the rates of reactions at the gas-liquid iron interface is briefly reviewed. Deductions from recent studies of the rates of decarbur- ization of carbon-saturated liquid iron indicate ideal adsorption behaviour for sulphur over a wide temperature and composition range. This is in fair accord with available infor- mation on surface tensions in the Fe-C-S system. Previously unpublished results for the kinetics of the 14C02-CO exchange reaction are in accord with ideal absorption of oxygen on liquid iron. The derived value for the ideal adsorption coefficient of oxygen at 1550¦C is in quantitative agreement with measurements of the depression of surface tension in the Fe-0 system. Consideration is given to the applicability of such results to the violently agitated systems of steelmaking.

Jan 1, 1980

By A J. Morrison, M Yahyaei, J S. Siong, J Wang, K Runge

The flotation cells used to upgrade ultrafine metallurgical coal (-250 µm) are usually poorly controlled leading to unnecessary loss of combustibles from the flotation system. This is mainly because coal flotation cells are typically controlled for process stability rather than optimisation of flotation performance. This is especially true for a flotation device commonly used in coal applications in Australia – the Jameson Cell. This then provides an opportunity to improve the flotation performance by shifting from a stabilising control strategy to a proactive optimising control strategy. For an optimising control strategy, the control system will require a means of relating and then measuring in real-time, the effect of changing operating conditions on the coal flotation performance. Hence, the major aim of this work is to propose a possible model-informed process control strategy that could be used for real-time performance optimisation. In this study, industrial site work was conducted on an industrial-scaled Jameson Cell at a Coal Handling and Preparation Plant (CHPP) in Central Queensland, Australia where superficial gas velocity was controlled to six different levels. At the same time, other process variables such as froth depth and flotation feed properties were measured. The empirical models developed from this study suggested that combustible recovery is a function of superficial gas velocity, froth depth, feed solid content and feed ash content and that a peak in combustible recovery existed as a function of superficial gas velocity. This led to the development of a model-informed control strategy that aimed to maximise the combustible recovery by determining and then operating the cell at the superficial gas velocity at which the peak occurs. This peak superficial gas velocity was found to be only a function of feed solid content. Based on these findings it would seem possible to operate a Jameson cell at peak performance by online measurement of feed solid content, prediction of the optimum superficial gas velocity and stabilising control to maintain operation at that superficial gas velocity set point. The development of this modelinformed control strategy can serve as a basis for the development of a more sophisticated modelpredictive control (MPC) system. However, more work will need to be done to improve the predictivity of the combustible recovery model by measuring and modelling performance over a wider range of operating conditions.

Aug 24, 2022

The Big Bend and Cobra molybdenum prospects which occur near the margin of the Karamea Batholith in the Northwest Nelson molybdenum province are compared. The Big Bend Prospect is a 3000 m by 800 m area of disseminated pyrite and anomalous molybdenum associated with Cretaceous porphyry intrusives and later argillic and potassic alteration within Ordovician schists and phyllites adjacent to the batholith margin. The Cobra Prospect is a 1200 m by 1200 m area of weakly disseminated pyrite mineralisation and anomalous molybdenum-in-rock associated with moderate to strong quartz-molybdenite and quartz-orthoclase-molybdenite veining in quartzite.

Jan 1, 1979

The recommissioning of the plant at Mary Kathleen involved several distinct phases. The previous plant process was modified significantly, the plant capacity was increased by the addition of new equipment and the exist- ing equipment was in most cases overhauled. This equipment was either reused in its original duty or relocated. Maintenance requirements after the plant was cmommissioned were high because of the amount of modified equipment and also because some old items of equipment were deliberately not overhauled during recommissioning. The equipment that was overhauled has operated reliably. However some new equipment has not been as satisfactory.

Jan 1, 1978

Many stress measuring instruments use overcoring stress-relief principles but adopt different sensing techniques. Every technique is subject to certain limitations of rock types and conditions. To investigate the performance and reliability of the instruments in field measurement, a simple and practical approach has been developed to allow comparable laboratory results to be obtained which simulate in-situ rock and stress conditions. Four commonly used devices, the USBM deformation gauge, the CSIRO HI cell,the CSIR triaxial cell and the UNSW SI cell were thoroughly tested in the laboratory. Some conclusions have been drawn as to their suitability and reliability in different field conditions. Recommendations are provided for the choice of an appropriate technique for a given rock type and condition. A new thin-wall cell that overcomes the disadvantages of earlier devices has been developed and tested. Its laboratory performance shows that it has good prospects.

Jan 1, 1990

By Jorgensen FRA, Moyle FJ, Turner TM

Laminar flow furnace techniques and thermal analysis were used to study the combustion of Kambalda nickel concentrate and Collie coal. The study was made to ascertain the suitability of the latter as a replacement for the fuel oil currently burnt in a flash furnace at the Kal- goorlie Nickel Smelter. The coal was found to ignite at temperatures between 500-600¦C which was the same as that required for the most reac- tive component of the concentrate, namely py- rite. The rates of reaction of both the coal and concentrate were dependent on oxygen con- centration. Sulfur dioxide hindered the combus- tion of concentrate and of coal, the effect on the concentrate being the more pronounced. The effects of moisture content and the tendency for spontaneous combustion of the coal were also noted.

Jan 1, 1982

By Johns A. L

The concept of the Melbourne Underground Rail Loop and the organ- isation to achieve its construction are covered in the companion papers (Reference 1, 2) and will not be repeated here. The Victorian Railways, as well as being the eventual operator of the Loop when it is completed by MURLA, have also been responsible as "Contractors" to MURLA for the construction of the "cut and cover" or "box" tunnels and related approach works located on existing Railway property. These tunnel connections link the existing suburban system to the new underground works. The following tabulation indicates the significant work volume involved in this cut and cover tunnelling exercise and which is covered in some detail by this paper.

Jan 1, 1981

The control system of a mine winder or other variable speed drive has many component parts that must work together to provide the required functional performance of the machine, together with comprehensive safety features, reliability, maintainability, user-friendliness and efficiency. Modern winders use digital control technology extensively and hence software design is a major part of the overall system. It is not practical to simulate an entire mine winder in a single computer model because of the sheer mathematical complexity of the behaviour of many of the components. However, most component parts can be simulated quite easily, and related parts of the control system software can be simulated. Such simulations allow control software algorithms to be developed and tested in isolation from the real plant. Tests can be performed on the model without fear of injury to personnel or damage to the valuable plant. For example, speed regulator control algorithms and stability settings can be adjusted to and beyond the limits of stable operation, and near optimum settings can be found. This is particularly important, for example, when designing closed loop controls for emergency brake systems. Obviously, care must be taken to ensure that the computer model of the plant is realistic and takes into account as many non-linear features of the real plant as possible. Pure mathematical analysis of some systems is very difficult to perform when non-linear plant behaviour is involved. This paper shares a number of practical simulation experiences performed using commercially available software such as Matlab and Simulink to simulate various parts of the control system of a mine winder or other variable speed drive. Demonstrations of the operation of several different computer models are shown during the presentation of the paper.

Jan 1, 2005

By S Pigram, G J. Jameson

This paper is concerned with the tracking of particles in the froth phase of an aerated water/glycerol mixture. Experiments have been carried out in a specially designed laboratory flotation cell that allows formation of a deep froth. Phosphorescent tracer particles of various sizes were injected into the centre of a froth column where they were excited by ultraviolet lights, positioned at the back and front of the column. The motion of particles was captured on a digital camera with a green filter. The images from the digital camera were then transferred to a computer and an image analysis program was used to convert the colour intensity to the concentration of particles at each location within the froth. The tracer technique was used to determine the dispersion of hydrophilic particles and the variation of the concentration of solids with axial and radial positions.

Jan 1, 2005

By Readett D. J

Soluble salts can be removed from Bowmans lignite by water and acid leaching. The success of the removal of water soluble or acid exchangeable impurities is directly associated with the efficiency of dewatering these slurries. The filtration characteristics of a slurry at its natural pH (4.0) were poor, with a filter cake moisture of 65%. Acid treatment of the slurry at pH2 caused the filter cake moisture content to drop to 61 %. Various oils, oily surfactants and a flocculant were tested to determine the conditions for minimum filter cake moisture. A series of pilot scale filtration tests were conducted on flocculant dosed slurries with and without washing on a horizontal test unit. Moisture contents of 54% were obtained in laboratory testing using high additions of oily surfactant. For the pilot scale test work, moisture levels close to 60% were obtained with low flocculant additions, similar to results obtained in laboratory studies. Removal of soluble salts could be correlated directly to the final moisture content of the filter cake. This process of leaching followed by filtration resulted in the removal of approximately 75% (more than 80% with washing on the cloth) of the sodium chloride originally present in the lignite.

Jan 1, 1989

Surface oxidation is one of the most important factors that influence the flotation selectivity and recovery in the processing of complex sulphide ores. It is an inherent part of surface chemical reactions that determine whether the surface film formed on a sulphide mineral will act as a hydrophobic or hydrophilic one. Because of the highly complex surface chemistry and mineralogy involved the results of flotation tests may often be difficult to interpret. In this paper, the flotation behaviour of nickel-copper ores processed in the Sudbury area is discussed with emphasis on the effect of oxidation on individual minerals, primarily pyrrhotite. In general, moderate oxidation of a freshly ground ore promotes the flotability of all principal sulphides in the ore leading to a bulk flotation concentrate. The ease of individual mineral flotability under normal aeration conditions, which is chalcopyrite > pentlandite > pyrrotite, changes to pentlandite > chalcopyrite > pyrrhotite under oxygen-deficient conditions. This behaviour is correlated with the catalytic activity of these minerals for oxygen reduction. On the other hand, preferential oxidation of pyrrhotite may lead to a selectivity increase in flotation. Such a behaviour has been noted in the flotation of a pyrrhotite-rich process stream. The results have been discussed in the light of fundamental electrochemical interactions involving pentlandite, chalcopyrite, pyrrhotite, pyrite and grinding media and a mechanism has been proposed to explain the selectivity.

Jan 1, 1993