Search Documents

By Leslie W. Austen

ROTARY kiln operators will agree that some of the most severe conditions a refractory must stand occur in the hot zone of a kiln burning Portland cement, dead burn dolomite, magnesite, peri-clase, and similar materials. Frequently the operator is faced with factors beyond his control which drastically shorten the life of refractories. Shutdown due to mechanical failure can be serious if the period is of sufficiently long duration to cause the dropping of coating or the loosening of the lining. A change in slurry can affect the coating and cause ring buildup. A change in type of fuel and its effect upon the flame can cause a shift in location of the hottest zone. Weekend shutdowns or any other interruption can cause the operator trouble and may damage the refractories, since stopping and starting a rotary kiln is certainly more difficult than stopping and starting a motor. Some operators have tried to set an estimate of damage for each shutdown in equivalent days of running time. Conditions affecting the refractory may be roughly grouped in four classes: chemical attack, mechanical stress, thermal shock, and abrasion. Chemical Attack: The drive to obtain maximum production through a kiln demands maximum operating temperatures, temperatures which are limited more by the ringing up or melting of the clinker. This can cause interface temperatures at the junction of coating and refractory which require the use of a basic kiln block to withstand the chemical attack. Chemical changes take place within the refractory itself, especially in chemically bonded or unburned kiln blocks. These changes cause the formation of the ceramic or burned bond. Migrating liquids or fluxes from the kiln charge have an effect within the refractory and lead to mineral or glass formation. The alkalies, sodium and potassium, migrate into the refractory as silicates, chlorides, sulphates or other salts. They may move under capillary action or may be caused to move by volatilization with condensation in the cooler portion. Mechanical Stress: Concentrated stress may be caused by several factors or combinations thereof. I—The rings of refractories must be kept tight and rigid within the kiln, and this alone demands considerable force to hold the blocks in place. So that the force will not be concentrated, the blocks should fit the circle as perfectly as possible, with the faces in contact overall. 2—As the kiln is heated, thermal expansion takes place at the hot end of the kiln block. Since this disturbs the plane face it too can cause a concentrated stress at the two ends of the block, and shearing stress can be set up within the brick itself because of the difference in expansion between the two ends. 3—If a lining becomes loose and moves in the shell very severe stress can be set up, and as the kiln rotates this load changes and gives the effect of repeated loading. Permanent expansion of the refractory can also cause severe loading. 4—Not least important, flexing of the kiln is frequently the cause of concentrated stresses. Thermal Shock: Thermal shock, the result of heating and cooling too rapidly, occurs on starting and stopping or when a large patch of coating drops, exposing the bricks. Again, its destructive effect is often the result of phase change, liquid to solid or the reverse; dense refractories loaded with glass-forming impurities are particularly susceptible. Thermal shock is a. problem with refractories set in the wall or roof of a stationary furnace, and becomes even more serious in a rotary kiln, the tendency to spa11 being magnified with movement and concentration of stress. Uniform rate of feed and loading insures both better coating and a more uniform stress. Abrasion: If the refractories do not take a coating, abrasion can become a most destructive factor. Movement of the lining in shell or movement of loose blocks causes abrasion, which is also most destructive if the refractories do not take a coating. An analysis of the problem of basic lining for the hot zone reveals, therefore, a number of desirable characteristics: high refractoriness, basic chemical reaction, resistance to spalling, good strength at all stages, ability to take coating, true sizing, volume stability, and abrasion resistance. Increased demand

Jan 1, 1953

By D. Harrington

One of the main functions of the United States Bureau of Mines is to obtain and disseminate information that will promote safety in and around mines, and the health and safety of employees engaged in mining. Serious health and safety conditions arising out of contamination of air in metal mines by dust, fumes from explosives and fires, and absorption of oxygen by timber and other causes, led the Bureau of Mines to cooperate with the United States Public Health Service in the study of dust occurrence and ventilation in metal mines in various parts of the country. A. J. Lanza, of the U. S. Public Health Service, and Edwin Higgins, mining engineer of the U. S. Bureau of Mines, in 1915, made a detailed study in the mines around Joplin, Mo.; their reports1 are now available. In 1916, 1917, and 1918, a similar study was made in the Butte, Mont., region by Doctor Lanza and D. Harrington, mining engineer of the Bureau of Mines; the reports of this investigation will be available soon. In 1919, the study was continued in some of the Arizona mines by D. Harrington, of the Bureau of Mines, and G. E. McElroy and R. A. Koronski, of the U. S. Public Health Service, the underground work being completed in June, 1920; these reports are now being prepared for publication. In the spring of 1920, the scope of the work was extended, with D. Harrington in charge as supervising mining engineer, and short studies were made in the mines of the Coeur d' Alenes in Idaho and around Oatman, Ariz. It is hoped soon to extend the work into mines of California, Nevada, Colorado, Michigan, and Minnesota, and ultimately to other states should the mining companies be willing to coöperate. While the coöperation of the mining companies is necessary, the companies are put to practically no expense other than supplying a guide to accompany the investigators underground, the length of time spent

Jan 1, 1922

By J. T. Norton, N. J. Grant, A. R. Chaudhuri

MOST of the recent work to establish the mech-anism of creep in metals at high temperatures has utilized aluminum as the experimental material. It was thought desirable to initiate an investigation of a hexagonal close-packed metal, because of the relatively simple slip system, and compare the observed deformation characteristics with those that have been observed for the face-centerd cubic metals. High-purity magnesium was chosen for this purpose, first, because its strength and other mechanical properties are similar to those of aluminum in the same temperature range, and second, because the existing equipment was ideally suited to observe magnesium during creep. It is proposed in this paper to present a pictorial and qualitative account of the changes that high-purity magnesium undergoes during creep at 500°F. The characteristics of deformation of aluminum described below have been observed by various workers and accounts of these may be obtained from the papers of Chang and Grant.'- These characteristics are: slip, subgrain formation, grain boundary sliding and migration, fold formation, deformation bands, and kink bands. It is well known that in a flat magnesium specimen, slip on the basal plane (0001) in the [1120] direction results in the formation of straight bands on the surface of the specimen. Schmid and co-workers' have shown that this system is operative in the temperature range of -185" to 300°C (-300° to 572°F). They have also shown that a second system, slip on the pyramidal planes {1071} or {1012} in the [1120] direction, is operative at temperatures higher than 225°C (437°F). Between 225° and 300°C (437" to 572°F), therefore, deformation by both these systems is expected. Bakarian and Mathewson5 confirmed the occurrence of pyramidal slip on the {1011} plane and found that it resulted in irregular markings on the surfaces of their specimens. Burke and Hibbard6 obtained evidence of pyramidal slip in single crystals of magnesium deformed at room temperature. Bakarian and Mathewson5 suggested that the irregular appearance of these bands was due to slip on both of the pyramidal planes occurring simultaneously but in the same direction, the close angular relationship between the planes making this process possible. Furthermore, since neither of these planes is close enough to the basal plane, slip on the latter does not exhibit the irregular appearance of slip bands resulting from pyramidal slip. Experimental Procedure High-purity magnesium, supplied by the Dow Chemical Co., was used in these experiments. The analysis was as follows: Al, 0.0002 pct; Mn, 0.0018; Fe, 0.0024; Cu, 0.0002; Sn, 0.001; Ca, 0.01; Ni, 0.0003; Zn, 0.01; Pb, 0.0005; Si, 0.001; and Mg, 99.972. The magnesium was supplied in the form of 1/2 in. diam rods. The specimens had an overall length of 21/4 in., the round ends being threaded to fit the specimen holders. The previously round 3/16 in. diam gage section of the specimen had two parallel flats machined on opposite sides for microscopic observation, yielding a test zone having the dimensions of lx3/16x7/64 in. The specimens were electrolytically polished (without prior mechanical polishing of the machined flats), in a solution composed of 375 ml of ortho-phosphoric acid and 625 ml of ethyl alcohol.' The cathode was a stainless steel sheet bent so that the specimen was completely surrounded. The voltage for successful polishing was 1.5 v at 100 to 300 milli-amp current. Electropolishing for about 45 min sufficed to obtain a good metallographic surface on the specimens after they had been machined. The creep tests were performed under constant load, and two types of equipment were used. In the first, designed by Servi and Grant,V he specimens were beam-loaded, and a furnace could be lowered to surround the specimen. As the microstructural changes could not be observed during the course of the test, the tests had to be interrupted periodically by removing the specimen for microscopic examination. The second unit was a high temperature microscopy furnace designed by Chang and Grant.' The furnace was fitted with an optically flat quartz window having area dimensions 1.25x0.5 in., so that the whole test portion could be viewed through it at magnifications up to x240. The metallurgical microscope had three mutually perpendicular axes of motion, and, in addition, it was possible to measure angular displacements by rotation of the eyepiece. It was thus possible to make precise observations of the specimen during creep, and micrographs could be taken by attaching a camera to the eyepiece of the microscope. The average grain size of the specimens that were tested was about 1 to 3 mm. This grain size could

Jan 1, 1954

By Kim C. Harden

INTRODUCTION The purpose of the following discussion is to present the state of the art of solution mining. Since the economics of a mining method ultimately determines its applicability and viability this presentation shall revolve around the costs of in- situ solution mining. First the assumed physical characteristics of the hypothetical ore body are described, followed by the appropriate operating assumptions. Then after a brief discussion on the type of surface plant to be used, the assumed project time tables and costs for Texas and Wyoming are presented. Finally, the economics of in-situ uranium leaching are analyzed through the use of discounted cash flow rate of return analysis. ORE BODY CHARACTERISTICS The assumption of the ore body characteristics is probably the most variable portion of this discussion. The characteristics that have been used are based mainly on state of the art technology, however, consideration of the most common depths of ore, ore thicknesses, and permeabilities also influenced these assumptions. In addition, it is assumed that these assumptions are equally applicable to Texas and Wyoming. The average grade of the ore is assumed to be .09% U308 with no apparent disequilibrium. The average thickness of ore is 2.29 m (7.5 ft) which results in an average grade-thickness (GT) of .675. The assumed depth to the top of the ore is 121.92 m (400 ft), the ore density is placed at 1.78 gm/cc (18 cu ft/ton), the porosity is estimated to be 28% and the permeability 1 darcy. These assumed ore body characteristics are shown in Table I. In addition, it is specified that the costs to be later discussed are based on a minimum GT cut-off of 0.15. It is more common to use GT cut-offs of 0.30 to 0.50 but GT cut-offs as low as 0.15 in conjunction with a minimum grade of 0.05% U308 have been used in the past with success and is considered state of the art. The ultimate percentage of uranium recovered from the ore is left to the discretion of the reader since the costs and economics are based on pounds recovered by the surface plant. OPERATING AS.SUMPTIONS An annual production rate of 200,000 lbs U308!yr was chosen for this example. In order to maintain this production rate, based on the ore body characterized above, a flow of 4731 liter/min (1250 GPM) with a recovery solution grade averaging .039 gm U308/liter is assumed. A regular 5 spot well field pattern is used with a well spacing of 21.5 m (70.7 ft) between like wells and 15.24 m (50 ft) between unlike wells. This well spacing gives each well an area of influence equal to 232.25 sq m (2500 sq ftl. An excess wells factor of 1.17 is used to estimate additional monitor wells and well field boundary wells. Each production well is expected to yield an average flow rate of 37.85 liter/min (10 GPM). In addition it is assumed that the ore body has a good shape in that it is not tenuous and narrow but has at least an average width of 200 ft. The process chemistry required for this ore body is assumed to be based on the sodium carbonate System- Oxygen is the chosen oxidant. Sodium chloride elution followed by precipitation with hydrogen peroxide makes up the remaining portion of the process. A fluidized up-flow ion exchange system is specified. The operating assumptions are listed in Table II. Restoration of the ore body shall be assumed to be accomplished through the use of ground water flush. Other methods may be considered as having to fall within the costs estimated for a ground water flush in order to be economic. In Texas it is assumed that a high capacity disposal well (200 GPM +I is required and in Wyoming evaporation ponds covering approximately 35 acres are to be used. No specific cost has been given to restoration. Instead only the additional capital investment for restoration equipment is given. Then, one year of restoration operating expense is estimated and included as the operating expense for one year beyond the last pound of U308 produced. It is also assumed that restoration will be pursued in the mined out areas of the ore body contiguous with ongoing production.

Jan 1, 1980

By Daniel R. Shawe

Ore deposits of the western U.S. are divisible broadly into two genetic groups, a smaller one that fits the plate tectonic model of subduction and a larger one that appears unrelated to subduction. Some of the middle Paleozoic and lower-middle Mesozoic ore deposits in the western U.S. are associated with eugeosynclinal rocks and lie a few hundred kilometers west of reconstructed continent margins. These deposits probably formed as a result of subduction beneath oceanic or thin continental crust that was analogous to subduction predicated for the Kuroko massive sulfide deposits of Japan. Some middle Mesozoic porphyry copper deposits may have formed east of the continental margin when subduction-generated magmas were emplaced high in continental crust in a manner analogous to subduction-generated magmas that formed the Andean porphyry copper deposits. Most Cretaceous-Cenozoic ore deposits lie in a broad region extending many hundreds of kilometers east of the continent margin and characterized by conjugate tectonic zones, high terrestial heat flow, and low seismic velocity in the upper mantle. The deposits likely were formed in relation to magmas generated along the conjugate tectonic zones during differential northwestward drift and internal wrenching of the continental plate.

Jan 1, 1978

By J. J. Gilman

The data presented indicate that the critical shear stress and strain-hardening Thedatapresentedrate of a zinc monocrystal depend on the orientation of its slip direction with respect to its external boundaries. The tendency of a crystal to form deformation bands also depends on its shape. THE plastic behavior of pairs of zinc monocrystals in which both members of the respective pairs had the same orientation with respect to the longitudinal axis, but each had different orientations with respect to their rectangular external shapes, were compared in this investigation. The purpose of the investigation was to see what influence the shape or surface of a zinc crystal has on its mechanical properties. In a previous investigation of triangular zinc monocrystals,1 anomalous axial twisting was observed which seemed to be related to the triangular shape of the crystals. Wolff,' in 400°C tensile tests of rectangular rock-salt crystals bounded by cubic cleavage planes, found that, of the four equivalent slip systems, the two with the "shorter" slip directions yielded and produced slip lines at lower stresses than the other two. This observation and the work of Dommerich³ as formulated by Smekal4 as a "new slip condition" for rock-salt: "among two or more slip systems permitted by the shear stress law, with reference to the formation of visible slip lines by large individual glides, that slip system is preferred which has the shortest effective slip direction." More recently, Wu and Smoluchowski5 reported essentially the same effect for ribbon-like (20x2x0.2 mm) aluminum crystals at room temperature. Experimental Chemically pure zinc (99.999 pct Zn), purchased from the New Jersey Zinc Co., was the raw material. Glass envelopes, containing graphite molds and zinc, were evacuated while hot enough to outgas the graphite but not melt the zinc. At a vacuum of about 0.2 micron the envelopes were sealed off and then lowered through a furnace at 1 in. per hr so as to melt and resolidify the zinc and produce mono-crystals. One-half of one of the molds is shown in Fig. la. Each mold consisted of four pieces from a cylindrical graphite rod that was split longitudinally and transversely at its midpoints. Rectangular milled grooves 0.050 in. deep and % in. wide formed the mold cavity when the split halves were assembled with twisted wires. Fig. lb shows the specimen shape obtained when the top and bottom mold-halves were rotated 90" with respect to each other. Good fits prevented leakage and excess zinc was necessary to provide enough liquid head to fill the mold completely. In removing soft crystals from the molds it was impossible to avoid small amounts of bending. However, manipulations were carried out whenever possible with the crystals protected by grooved brass blocks. All specimens were annealed prior to testing. From the top and bottom sections of each crystal, X-ray specimens and tensile specimens 7 to 8 cm long were sawed. The tensile specimens were annealed inside evacuated tubes for 1 hr at 375°C. Next the crystals were cleaned and polished by 2-min dips in a solution of 22 pct chromic acid, 74 pct water, 2.5 pct sulphuric acid, and 1.5 pct glacial acetic acid.' Cleaning was followed by a 10-sec dip in a 10 pct caustic solution, then washed in water and alcohol, and dried. This treatment results in a bright surface covered by an invisible oxide film. The testing grips were a slotted type with set screws and were supported in a V-block during the mounting operations in order to avoid bending the crystals. A schematic diagram of the recording tensile-testing machine is shown in Fig. 2. The machine has been described elsewhere.' The head speed was 0.3 mm per sec for all tests. The crystal orientations were determined by the Greninger X-ray back-reflection method with an estimated accuracy of 1. Description of Crystal Geometry A schematic picture of a rectangular zinc mono-crystal is shown in Fig. 3. ABD designates the front edge of a basal plane (0001) of the crystal, the only active slip plane for zinc at room temperature. Of the three possible (2110) slip directions, the active one is indicated by an arrow. Cartesian coordinates are taken parallel to the specimen edges. The normal, n, to the basal plane (n is parallel to the hexagonal axis) has the direction cosines a, ß and ?. X0 = 90 — y is the angle between the longitudinal axis and

Jan 1, 1954

By R. C. Temps, G. E. Aiken

Compania de Acero del Pacifico, S.A., the sole Chilean steel producer, is adding to the expanding Chilean economy with development of the El Algarrobo mine. Expected to go on stream early in 1962, Algarrobo is a conventional open pit mine that will include facilities for ore extraction, crushing and screening, rail transport to the harbor at Huasco, modern ship-loading equipment and maintenance shops. CAP anticipates producing 1.38 mil- lion tons annually of high-grade ore for national and world market consumption. Chilean and North American management and engineering teams combined more than a decade ago in the financing and building of CAP'S Huachipato integrated steel plant. A similar performance is being achieved in northern Chile near the town of Vallenar with the opening of a 50-year supply of iron ore from the Algarrobo deposit. This successful intra-American undertaking deserves special mention in these times when some U.S. foreign assistance programs must be defended, particularly with respect to Latin America. North American financial participation in Algarrobo, through the Export-Import Bank of Washington, represents the greatest portion of the $24 million being invested.

Jan 3, 1962

By L. J. Buck

Lead smelting in the ore hearth, first practiced in Europe, whence the traditional name "Scotch hearth, and later developed in America to its present efficiency, is based upon the roast reduction process and is applicable to relatively high-grade galena concentrates. The roast reduction process embraces not only the roast reactions: 2PbS + 70 = PbO + PbSO4, + SO2 PbS + 2PbO = 3Pb + SO2 PbS + 2PbSO4 = Pb + 2PbO + 3SO2 but also, by reason of the addition of extraneous fuel, the reduction reaction: 2PbO + C = 2Pb + CO2 Thus in the ore hearth the roasting of lead sulphide, forming lead oxide and lead sulphate, the reaction of lead oxide and lead sulphate with lead sulphide producing lead, and the reduction of lead oxide by carbon producing lead, go on simultaneously. The Ore Hearth Function of the Ore Hearth.—The ore hearth, through the roast reduction process, provides for the extraction of lead and the immediate disposal of the smelting products—fume, hearth slag and lead, all of which are subsequently treated as follows: the fume is recovered in the flue system and baghouses, mixed with concentrates, and returned to the ore hearth in the form of ore mix; the hearth slag is smelted in a blast furnacc for the further recovery of lead; and the lead is refined and cast into a marketable product. Concentrates Amenable to Ore-hearth Smelting.—Only concentrates that are high in lead content, 70 per cent or more, are ordinarily considered amenable to ore-hearth smelting. Silica should not exceed 2 per cent and iron is allowable only to 4 per cent. These slag-forming constituents occlude both sulphide and mctallic lead, prevent the elimination of sulphur and decrease the lead extraction. Lime and magnesia are beneficial in that both favor a dry slag, promote elimination of sulphur, and prevent occlusions of metallic lead.

Jan 1, 1937

Discussion of the paper of Frank H. Kneeland, Safeguarding the Use of Mining Machinery. By B. F. Tillson and Arthur Williams. 1073 Discussion of the paper of Howard N. Eavenson, Safety Methods and Organization of United States Coal & Coke Co. By William H. Grady, Thomas W. Dawson, C. W. Goodale, J. Parke Charming, B. F. Tillson, George S. Rice, Arthur Hovey Storrs, Harry H. Stoek, Lawson Blenkinsopp, Arthur Williams, and Howard N. Eavenson. 1075 Discussion of the paper of J. Parke Channing, Enlarging the Worth of the Worker and the Perspective of the Employer. By Fred H. Rindge, Jr., S. A. Taylor, Elmer L. Corthell, and Philip W. Henry. . 1095 Discussion of the paper of Walther Mathesius, High Blast Heats in Mesaba Practice. By Joseph W. Richards, W. A. Forbes, J. E. Johnson, Jr., H. P. Howland, and Walther Mathesius. . 1100 Discussion of the paper of W. R. Shinier, Effect of Finishing Temperatures of Rails on Their Physical Properties and Microstructure. By William R. Webster, Henry M. Howe, A. A. Stevenson, G. K. Burgess, and Samuel L. Hoyt . 1107 Discussion of the paper of George K. Burgess and Sir Robert A. Hadfield, Sound Steel Ingots and Rails. By Albert Sauveur, Henry M. Howe, Henry D. Hibbard, Joseph W. Richards, F. W. Wood, and George K. Burgess. . 1112 Discussion of the paper of Henry M. Howe and Arthur G. Levy, Are the Deformation Lines in Manganese Steel Twins or Slip Bands? By J. E. Stead 1116 Discussion of the paper of F. C. Langenberg and R. G. Webber, Structures and Hysteresis Loss in Medium-Carbon Steel. By Henry M. Howe. . . 1117 Discussion of the paper of Charles H. MacDowell, German and Other Sources of Potash Supply. By George S. Rice, Charles H. MacDowell, and V.C. Grubnau . . 1118 Discussion of the paper of Joel H. Watkins, White-Burning Clays of the Southern Appalachian States. By H. Ries 1120

Jan 5, 1915

By C. R. Barrett, N. N. Singh Deo

The high-temperature steady-state creep behavior of a series of dilute copper-silicon alloys was studied to determine the effect of stacking fault energy on the creep-rate. The steady-state creep rate is, when taken at equivalent diffusivities decreases with decreasing stacking fault energy. The stress and temperature dependencies of is suggest that creep is a difusion controlled dislocation climb process. Electron microscopy studies of the creep substructure revealed: 1) the subgrain size is not a function of the stacking fault energy in these alloys, 2) the dislocation density not attributed to the subgrain walls seems to be higher during primary creep and decreases to a lower steady value during steady-state creep, and 3) the dislocation density during steady-state creep decreases with decreasing stacking fault energy. In the past few years numerous investigators have studied the influence of stacking fault energy on high-temperature creep strength. Most of these investigators have confined their attentions to studying the relationship between steady-state creep rate, is, and stacking fault energy, ?, when samples are tested under conditions of comparable stress and temperature. For the case of fcc metals, it was initially shown by Barrett and Sherbyl and since confirmed by many others2"4 that is decreases with decreasing ?, often following an empirical relation of the form i ?m where m is a constant about equal to 3. The application of theory to explain this observation has not been entirely successful. One of the main difficulties has been the almost complete lack of structural information (dislocation density, subgrain size, and so forth) for samples with different stacking fault energies, tested under high-temperature creep conditions. weertman5 has attempted to explain the stacking fault energy dependence of is on the basis of a dislocation climb mechanism. Assuming that both the rate of dislocation core diffusion and the ease of athermal jog formation decreases as ? decreases Weertman has argued that the rate of dislocation climb and hence the creep rate should also decrease as ? decreases. One questionable aspect of Weertman's analysis is the assumption that core diffusion down extended dislocations is slower than core diffusion down unextended dislocations. The only experimental work done in this area, by Birnbaum et al.6 on nickel and Ni-60 Co, has shown the core diffusivity to increase with decreasing ?. Theories of steady-state creep based on the diffusive motion of jogged screw dislocations often seem unable to predict even the qualitative nature of the es- relationship. Assuming that Weertman is correct in his assumption that the dislocation jog density decreases with decreasing ? then the jogged screw theories predict an increasing dislocation velocity with lower ?. It is usually assumed that the increase in dislocation velocity implies a corresponding increase in creep rate. However, two other factors must be considered before such a statement can be made. That is, we must know how both the mobile dislocation density and the effective stress (the difference between applied stress and internal stress) vary with ?. Significant changes in either one of these factors could outweigh any change in dislocation velocity accompanying a change in ?. And with the slower rates of recovery expected in low stacking fault energy materials it seems likely to expect both mobile dislocation density and effective stress to be dependent on ?. Sherby and Burke7 have suggested that stacking fault energy influences the creep rate in an indirect way. These authors cite evidence that the steady-state subgrain size generated during high-temperature creep is a function of ? decreasing with decreasing ?. Assuming the creep rate to be proportional to the area swept out by each expanding dislocation loop and that subgrain boundaries are good barriers to dislocations, then the creep rate should be proportional to subgrain area, hence increasing as ? increases. A critical evaluation of any of the above theories requires more quantitative information concerning the dislocation substructure generated during high-temperature creep. Accordingly this investigation was undertaken with an aim of studying the influence of stacking fault energy on tbe steady-state creep characteristics of a series of dilute copper-silicon alloys. Special emphasis was placed on studying the strain dependence of both the dislocation configuration and density. MATERIALS AND PROCEDURE Dilute copper-silicon alloys of the compositions shown in Table I were tested in tension at constant stress. The relative stacking fault energy of these alloys has been determined and is shown in Table 11. An Andrade-Chalmers lever arm was used to maintain constant stress and testing was carried out in a water

Jan 1, 1970

By F. H. Wilson, E. W. Palmer

Brass mills are familiar with a recurring problem which reveals itself during deformation of annealed metal as an opening up of cracks which are suggestive of a grain boundary pattern. A typical example is seen in Fig 1, which shows part of the convex surface of a cartridge brass disc which was slightly dished by the punching operation. Another illustration of the same type of defect was found in the surface of a finished cartridge case which split open on firing. These cracks, shown in Fig 2, were away from the split but indicate the presence of the type of weakness which permitted the splitting. Usually the weakness consists of separate cracks, the lengths of which are of the same order of magnitude as the grain size prior to the final anneal. Their typical appearance in a polished section is shown in Fig 3. This structure was found below the surface of a fractured tensile-specimen that had been cut from a large cartridge blank showing the defects on its convex surface. While the pattern formed by these cracks suggests a grain boundary origin, the cracks bear no relation to the currently existing grain structure. Thus Fig 3 shows that the grains have grown up to cracks already present. Since it is doubtful that the cracks were present in the metal before the anneal, they must have formed during the anneal but prior to recrystallization. The term "fire-cracking" has been generally applied to cracking that occurs during an anneal under the influence of internal stress, but refers more specifically to obvious macroscopic cracking attributable to the presence of a low melting phase, usually lead. Since the type of cracking described above may occur when the lead content is very low, we have considered it a somewhat different phenomenon, and have called it "inter-granular parting." While most examples involve cartridge brass, intergranular parting has also been observed in the fabrication of large seamless tubes from discs of both 85/15 red brass and 70/30 cupro-nickel. Similar cracking in nickel silver was investigated by Jones and Whitehead,1 who showed that it could occur during healing or cooling. That which occurred on heating they called "fire cracking," and they suggested that, a transformation at about 320°C might account for its occurrence. It was felt in this laboratory that the observed parting was probably one aspect of the general observation, first made by Rosenhain and Archbutt,2 that a tendency toward intergranular fracture under tensile stress increases with increasing temperature and decreasing rate of strain. In this case the stress involved would be internal. The rate of strain would be exceedingly slow, a localized internal creep. Reference to the literature uncovered no efforts to extend the observations of Rosenhain to conditions involving only internal stress. Accordingly, an exploratory research, sufficient in detail to satisfy us as to the probable truth of this explanation of the observed intergranular parting, was undertaken. The internal stresses present during the early stages of an anneal (prior to recrystallization) would be from two sources: residual stresses developed during deformation, and thermal stresses caused by uneven heating and expansion. Thermal stresses would vary widely according to shape, size and manner of heating, and can be considered as supplementary to residual stresses. It seemed necessary to determine the stress and temperature conditions under which parting would occur in a relatively short time, and then to establish whether or not in- ternal stresses may persist to an extent adequate to cause parting at such temperatures. (Jones and Whitehead1 and Moore and Beckinsale3 made tests which indicated that stress relief required an appreciable time.) During the course of the research the desirability of studying the effect of grain size became apparent, and this factor is one of the major variables of our investigation. Intergranular Parting under Tension at Elevated Temperatures In early experiments, hard 70/30 brass tensile specimens, with unknown residual stresses, held for 10 min. at applied stresses from 30,000 to 40,000 psi at temperatures from 300 to 350°C, showed no macroscopically visible cracks when unloaded and cooled, but cracks very similar in appearance to those observed in commercial practice were revealed in these specimens by pulling them to fracture. Annealed specimens, on the other hand, showed no cracks in such experiments, apparently because they deformed plastically at stresses below those necessary to cause parting in a reasonable time. Hence, the specimens used for this study were first strengthened by cold tensile elongation, giving them an unavoidable residual stress pattern (determined largely by grain size and orientation) which would, however, correspond in direction, at least, to the stress pattern obtained under stress at temperature. A variation in these residual stresses might be expected with variations in grain size, but following any given anneal the reproducibility of stress pattern should be as good as that of the grain size measurement. With no information as to the effect of the amount of prior deformation, tests were conducted on specimens given the same cold elongation, using a stress applied at temperature which was a constant proportion of the stress required to produce this elongation. In

Jan 1, 1950

By E. Lifshin, R. E. Hanneman

QUANTITATIVE applications of the electron micro-beam probe frequently involve the evaluation of complex mathematical expressions and/or the analysis of large amounts of experimental data. The purpose of this communication is to describe briefly a versatile and useful computer program system that is applicable to analyze rapidly a wide variety of practical microprobe problems. This system consists of a group of ten FORTRAN programs that can be stored on tape, cards, or in the memory disc of the computer. These programs, or links, can be run individually or in any prespecified sequence without interrupting the operation of the computer or without destroying information which is being transfered from one link to another. For the program system described here a GE-235 computer with disc storage was used, so that the DCHAIN method of program linking was employed. Included in the library are programs to: 1) initiate analysis of a new set of data and transfer control between all other programs in any predetermined manner; 2) generate theoretical calibration curves of composition vs relative intensity; 3) generate empirical deviation parameters from least-square fits of experimental calibration data from standards of known composition; 4) convert raw X-ray data to corrected composition; 5) determine inter diffusion coefficients by Matano analysis of con centrat ion -distance data on a uniaxial diffusion couple; 6) determine activation energies and frequency factors of temperature-activated processes such as diffusion; and 7) generate calibration curves for determination of the thickness of thin films using microanalysis. A detailed description of these computer programs and their underlying principles is available on request from the authors."' The first program to generate theoretical calibration curves of corrected relative intensities vs composition uses the Poole and Thomas atomic number correction' and the Philibert absorption factor' with a voltage-dependent mass absorption coefficient for electrons in the alloy. A modified Castaing fluores- cence correction is also used which includes the effects of both Ka and KO radiation and over voltage.' Once the theoretical curves have been calculated in 1 wt pct intervals, these results are least-squares fit to obtain Ziebold deviation parameters' which are stored in COMMON in the computer memory. The net discrepancies between the original theoretical calibration curve and the regenerated curve using the Ziebold parameter are computed. Although this link is explicitly written for K-K fluorescent interactions, it can be applied to K-L, L-K, and L-L interactions as previously disc~ssed."~ Similar programs have also been written to utilize the Wittry fluorescence correction, Birks combined corrections, and various other corrections.' These modified programs have proved to be quite useful for quantitative comparisons of the results of the various theories. The program for conversion of raw X-ray data to corrected composition includes corrections for drift, backround, and instrumental dead time. The corrected intensities are converted to composition by use of the Ziebold equation"2 and parameter obtained from the program system. The results can be obtained for either atom or weight fractions. In addition to accurately computing interdiffusion coefficients the Matano analysis program calculates least-square smoothed values of concentration, concentration gradient, and curvature for each point on the raw input concentration profile. In order to obtain high accuracies a unique method of performing a least-square polynomial fit to incrementally advancing profile segments which overlap is used.' This program has been successfully modified for use in ternary diffusion problems3 and can readily be modified to handle analysis of diffusion profiles which include phase boundary discontinuities. This link is generally applicable to analysis of interdiffusion data obtained by other techniques as well as by the microprobe. The primary function of the next program is to least-squares fit experimental diffusion data to the normal Arrhenius function: D = Doexp(-Q/RT), to obtain values of Do and Q. In addition the probable error and one, two, and three u statistical confidence limits of DO, Q, and log D are evaluated. This program is also directly useful for analysis of any other simple temperature-activated processes including conductivity, and certain deformation and chemical processes. The program to generate calibration curves for film-thickness determination using the microprobe is based on a numerical integration of the equation derived by Cockett and ~avis.' Values of film thickness obtained by this program for copper on various substrates are in good agreement with measurements made by other techniques. Versions of the above program system have been prepared for use with or without a remote teletype connection to the computer for processing on either a real-time or time-share basis. The instrumentation coupling a microprobe to a teletype for automatic data collection and analysis by the presently described program system has been reported elsewhere by the authors.' If teletype equipment is not used to communicate with the computer, standard methods of card reading and tape reading can be used. In either

Jan 1, 1967

E. O?C. Acker Truman H. Aldrich John H. Allen W. Lawrence Austin W. S. Ayres David Baker Andrew A Blair Walter M. Brodie H.H. Burden Charles Butters

Jan 1, 1936

Most of the production of germanium in the U. S. is from byproducts of smelting Tri-state zinc ore. Only in England has commercial manufacture been reported from coal.

Jan 1, 1953

By E. A. Trager, A. W. McCoy, H. R. Shidel

Sampling of the fluid from oil wells for percentages of oil, emulsified oil, and water during the last two years has brought out some interesting facts concerning oil-water emulsion. This result led to a laboratory investigation of emulsion, which substantiated the conclusions made from the field observations. The purpose of this paper is to present the information collected, the laboratory experiments, and our interpretation of the same. In order to define emulsified .oil exactly, give its synthesis and origin, and to show how and when it is formed in the wells, the work was necessarily divided into two separate lines—laboratory work and field observations. It is hoped that this study may lead to a discussion of such points so that the petroleum engineer, geologist, or technologist may be benefited by its practical bearing on oil-field management. Special credit is due Mr. Everett Carpenter, chief geologist of the Empire Gas & Fuel Co., for his assistance and cooperation in this work. Labobatory Investigations on Emulsified Oil Laboratory investigations were conducted in an attempt to learn the composition and some of the properties of emulsified oil, or B. S., as it is more commonly called, also to demonstrate, by laboratory methods, how B. 5. may be formed under conditions similar to those existing at the time a well is being pumped, and how it may be broken down. Literature bearing on this subject is widely scattered and very limited in scope. Bacon and Hamor define B. S., or bottom settlings, as "earthy matter, inert organic matter, or, in the case of Pennsylvanian petroleum, an emulsion of paraffin wax and water, which accompanies crude oil." In this discussion we will limit the term B. S. to that heavy, dark-brown emulsion, composed of a physical mixture of water, oil, and air with some included inert matter, either organic or inorganic. Possibly the first step in a description of this product should be a description of its physical properties, but since most operators are quite

Jan 1, 1921

By J. A. Jaekel, W. C. Aitkenhead

Uranium deposits in the Spokane Indian Reservation, as well as those around Mt. Spokane, are essentially low grade, much of the ore containing less than 0.2 pct U3O8. The Mining Experiment Station of the Division of Industrial Research, State College of Washington, has been engaged in intensive research on the amenability of these low grade ores to froth flotation. The results: successful flotation of autinite, chief mineral constituent. At the outset of this work the goal was a concentrate of 1 pct U3O8 with a 90 pct recovery from ores containing less than 0.2 pct U3O8. Most of the work has been done on argillite ore from the Midnight mine on the Spokane Indian Reservation. The goal has not been attained using this ore, but samples of the granite ore from Mt. Spokane yielded successful results. For example, a concentrate containing 11.2 pcl U3O8 was produced from a Mt. Spokane high grade ore containing 1.27 pct U3O8 with a recovery of 97.8 pct. Another Mt. Spokane ore yielded a concentrate of 5.0 pct U3O8 from an ore containing 0.13 pct U3O8. with a recovery of 85 pct. This same ore gave a recovery of 93.5 pct when the grade of concentrate was reduced to 2.0 pct. It has been concluded that a successful method for floating autunite has been developed and that the mediocre results from the Midnight argillite ore are probably caused by the presence of some other uranium mineral or minerals less amenable to these reagents. The experimenters tested a third type of Washington ore, found on the Northwest Uranium Mines Inc. property on the Spokane Indian Reservation. This is a conglomerate of pebbles and small boulders of partially decomposed granite and is shot through with autunite. Its characteristics lie between those of the Midnight ore and the granite ore from the Spokane district. It responds better than the ore from Midnight but not as well as that from Mt. Spokane. As the fatty acids are the only type of collectors showing promise, investigation has been concerned with these acids and the optimum conditions for their use. The first method for treating the argillite ore from the Spokane Indian Reservation made use of Cyanamid's R-708 as a collector, a tall oil product described as a substitute for oleic acid. Although the investigators proved that R-708 is a collector for autunite when mixtures of autunite and silica sand are used, results on the ore were mediocre. Tests of other fatty acids revealed that the solid fatty acids of the saturated series are collectors for autunite and that their collecting power increases with the length of the carbon chain. The even carbon members of the whole series were tested from the 10 carbon acid (capric) to the 22 carbon acid (be-henic). The least expensive collector, stearic acid (18 carbon), proved to be a good one, so this was used in most of the tests. In first attempts with stearic acid, the collector was dissolved in various hydrocarbons and the solutions were added to the flotation cell. Cyclohexane, gasoline, fuel oil, kerosene, and other solvents were tried. Small amounts of high grade concentrates could be brought up, but recoveries were low. Finally emulsions of stearic acid were tried. It was discovered that stearic acid alone has little collecting power except when conditioning is carried out at high temperature. When hydrocarbon solvents were also present, it proved to be an excellent collector. An example of one emulsion that proved satisfactory for some ores is given as follows: 1 part stearic acid by weight, 1 part sodium oleate by weight, 1.2 parts kerosene by weight, 100 parts water. In some successful tests part of the stearic acid was replaced by oleic acid. The emulsions were made by agitating the stearic acid and sodium oleate together with hot water, then adding the kerosene and agitating while cooling. In the five tests reported in Table 1, 650 g of ore were ground with 650 cc water in a laboratory rod mill. The pulp was filtered to eliminate excess water and the ground ore transferred to a stainless steel beaker for conditioning at high pulp density. In most of the tests sodium hydroxide was added to the conditioner during agitation, then the collector emulsion, and finally the sodium silicate. The amount of alkali was adjusted to give a pH of 8.5 to 9.0 in the flotation cell. After conditioning the pulp was transferred to a laboratory flotation cell and the test completed in a normal manner. It is interesting to note that a deposit of high grade concentrate forms on the conditioning agitator and in the conditioning vessel, and at times on the agitator of the flotation cell itself. A few grams of concentrate running as high as 4 pct U3O8 were recovered from the conditioner when Midnight ore containing less than 0.2 pct U3O8 was treated. In the examples given in Table I this conditioner concentrate is calculated as part of the total concentrate. The authors have not yet fully explored the possi-

Jan 1, 1960

ZAY JEFFRIES, who has been awarded the Douglas medal, established in 1922 by a group of the friends of the late James Douglas for distin-guished achievement in non-ferrous metallurgy, is one of the most notable graduates of the South Dakota School of Mines where he took his B. S. degree in 1910. The following year he was manager of the Ideal Mining Co., at Custer, and in 1911 he became instructor in metallurgy at the Case School of Applied Science, Cleve-land, where he remained until 1917, and in 1918 he took his D. Sc. degree at Harvard. During all this period he was engaged in experi-mental and consulting work for the Electric Railway Improvement Co., t h e Cleveland Steel Tool Co., the W. S. Tyler Co., the Lincoln Electric Co., the Aluminum Castings Co., and the Cleveland wire di-vision of the General Elec-tric Co. He is now en-gaged in general consulting work, especially for the Aluminum Co. of America, the General Electric Co., and the National Tube Co. He has contributed to the Transactions papers on the determination of grain size in metals (with A. H. Kline and E. B. Zimmer) LIV, 594; grain growth phenomena in metals, LVI, 571; the tungsten-molyb-denum equilibrium diagram and system of crystalliza-tion, LVI, 600; grain size inheritance in iron and carbon steel, LVIII, - 669; effect of temperature, de-formation and grain size on the mechanical properties of metals, LX, 474; metallography of tungsten, LX, 588; physical changes in iron and steel below the thermal critical range, LXIII, and LXVII, 56; and the trend in the science of metals, LXX, 303. In addition to participating freely in the discussion of other papers before the Institute he has found time to contribute notable papers to the Institute of Metals (Great Brit-ain), the principal technical journals, and to write a book on "The Science of Metals" in collaboration with R. S. Archer.

Jan 2, 1927

I do not think too much emphasis can be placed upon creation of favorable climate for development of foreign mineral resources to feed the hungry maw of our industrialized nation. We have become dependent, not only upon the ten raw products indicated in Mr. Bancroft's article, but upon 71 mineral substances listed by DMPA as in short supply. Forty-four of these are metals, 9 are chemical minerals and 18 are nonmetallic minerals. Of this list only 8 are produced in any large quantity in the United States, and all are vital in peace-time industry. Even more, they are absolutely essential for defense. This represents our present needs. But if our consumption and requirements are projected over the next 25 years as is done by the President's Materials Policy Commission-The Paley Report-our future outlook becomes appalling. The divergence of consumption over production, even allowing for substitution and conservation, will widen in the future. This means our dependence upon foreign raw materials, mainly minerals, will grow. What are the chief foreign sources of minerals for our future needs? They are chiefly Latin America and the dominions and colonies of the Western European nations. The British Commonwealth countries contain in abundance those minerals which the U. S. lacks. Of 32 of the most critical minerals the Commonwealth is deficient in 7 and lacks only 1; whereas the U. S. is deficient in 18. Strikingly, our deficient minerals are abundant in the Commonwealth and several of their deficiencies are in excess in the U. S. Resources of the two nations complement each other. If Europe should be overrun by an unfriendly power that could control the destinies and resources of the European dominions and colonies, our industrial life would be placed in severe jeopardy. Therefore, I heartily endorse Mr. Bancroft's statements regarding the Point IV program, provided the program is wisely administered and implemented. It is from the underdeveloped countries, as pointed out by Mr. Bancroft, that most of our future mineral supplies will have to come. Many of the underdeveloped source countries are African colonies and dominions of Western European nations. Our present aid to Europe, therefore, is not, as many infer, a purely one-sided affair; it safeguards our future industrial development and security. Development aid directly to the underdeveloped countries through a well administered Point IV program, can do much, I believe, to safeguard our prosperity. I regard it as a wise investment for future U. S. mineral needs. Dr. Alan M. Bateman Department of Geological Sciences Yale University Mr. Howland Bancroft's article, The Broadening Road to Foreign Investment, appeared on page 666 of the July MINING ENGINEERING.

Jan 1, 1952

By C. T. Wei, A. Kelly

USING a recently developed X-ray method, reported by Schulz,2 it is possible to make a rapid survey of the perfection of a single crystal at a particular surface. This technique has the advantage of allowing a large surface of a specimen to be examined by taking a single photograph and it compares well with other X-ray methods in regard to sensitivity of detection of small angle boundaries. During the course of a survey of the perfection of large crystals of aluminum produced by a number of methods, an examination has been made of a number of single crystals produced from the melt using a soft mold (levigated alumina)." Crystals grown by this method are known, from an X-ray study carried out by Noggle and Koehler,3 to contain regions where they are highly perfect. In the present work, it has been possible to obtain photographs showing directly the distribution of low angle boundaries at a particular surface of these crystals. single crystals were grown from the melt using the modified Bridgman method with a speed of furnace travel of -1 mm per min. These were about 1/10 in. thick, 1 in. wide, and several inches long. The metal was 99.99 pct pure aluminum supplied by the Aluminum co. of America. The crystals were examined by placing them at an angle of about 25° to the X-ray beam issuing from a fine focus X-ray tube of the type described by Ehrenberg and Spear4 and constructed by A. Kelly at the University of Illinois. A photographic film was placed SO as to record the X-ray reflection from the lattice planes most nearly parallel to the crystal surface. The size of the focal spot on the X-ray tube was between 25 and 40 u, and the distance from the X-ray tube focus to the specimen (approximately equal to the specimen to film distance) was -15 cm. White X-radiation was used from a tungsten target with not more than 35 kv in order to reduce the penetration of the X-rays into the specimen. Exposure times were approximately 1 hr with tube currents between 150 and 250 microamp. The type of photograph obtained from these crystals is illustrated in Fig. 1, which shows a number of overlapping reflections from the same crystal. The large uniform central reflection is traversed by sets of horizontal white and dark lines. These two sets run mainly parallel to one another. Lines of one color are wavy in nature and often branch and run together. Large areas of the crystal surface show no evidence of these lines whatsoever. The lines are interpreted as being due to low angle boundaries in the crystal, separating regions which are tilted with respect to one another. A white line is formed when the relative tilt forms a ridge at the interface and a black line is found when a valley is formed. In a number of cases, the lines stop and start within the area of the reflection and often run into the reflection from the edge, corresponding to a low angle boundary starting from the edge of the crystal. The prominent lines run roughly parallel to the direction of growth of the crystal although narrow bands can run in a direction perpendicular to this; see Fig. 2. Although they may change their appearance slightly, the lines tend to occur in the slightly,Same place in the X-ray image and to maintain their rough parallelism when the crystals are reduced in thickness by etching. Thus the low angle boundaries can occur at any depth within the crystal. The appearance of the lines is unaffected by subjecting the crystal to rapid temperature changes, such as plunging into liquid nitrogen or rapid quenching from 620°C. From the width of the lines on the x-ray reflection, values can be found for the angular misorienta-tion of the two parts of the crystal on either side of a boundary. The values found run from 1' to 10' of arc, but values of UP to 20' have sometimes been found, e.g., the widest lines on Fig. 2. These mis-orientations are much less than those commonly found in crystals possessing a lineage structure. When a number of a and white lines occur, running in a roughly parallel direction across the image of a Crystal, the total misorientation corresponding to lines of one color is approximately equal to that corresponding to lines of the other color. The interpretation of the lines as due to low angle boundaries has been checked in a number of ways. Photographs taken with different specimen-to-film distances distinguish lines due to low angle boundaries from effects due to surface relief of the specimen. Normal Laue back-reflection photographs, taken with the beam irradiating an area of the surface showing a number of the lines, show white lines running through each Laue spot. Black lines are set to see by this method. X-ray photographs were also taken, using the set-up described by Lam-one et al.5 when the beam straddles regions giving rise to lines in the Schulz pattern, split reflections are observed within the Bragg spot. The misorienta-tions calculated from the separation of these reflections and that found from the widths of the lines on the schulz technique patterns show good agreement. An exposure was made with Lambot technique of an area of the crystal showing no evidence of low angle

Jan 1, 1956

By Jose A. Ruiz

INTRODUCTION For heterogeneous non-catalytic solid-gas reactions carried out in fluidized bed reactors, nominal bed temperature is an average value between gas and solid. For highly exothermic reactions, actual particle temperature can be up to hundred degrees above termocouple temperature, since heat dissipate at slower rate than heat generation during some steps of transformation. These micro instabilities at particle level can displace thermodynamic equilibrium from the desired phase to others. This effect is important when relatively narrow range of phase stability exists, like in sulphation roasting of sulphides, where bed discharge contains, in addition to the desired sulphate others metastable phases such as basic sulphate and ferrite. For example, for copper-iron sulphide concentration roasted below 680°C, no cupric ferrite is formed, as shown by Jakob et al., therefore the separate Kellogg's stability phase diagrams Cu-S-O represent the roasting (Fig.l). At temperature above this one, like 760°C for example, phase stability changes from CuSO4 to the basic sulphate Cu0•CuSO4. Solid state reaction between Cu0•CuSO4 and Fe203 also occurs to form cupric ferrite, Cu0•Fe2O3, therefore the Cu-Fe-S-O Kellogg's phase diagram of Fig. 1 (continuous line) represents this condition of roasting. Although both Cu0•CuSO4 and Cu0•Fe2O3 are metastable phases under normal operating conditions of sulphation roasting(1-10% SO2, 1-10% 02 and 680°C, points A and B,Fig. 1) sulphation of these species and particularly ferrite are slow and limited due to diffusional control. This explain why reactors discharge contains several phases: CuSO4, Cu0•CuSO4, CuO•Fe203 plus small amounts of CuS and FeS due to the baclonixed conditions of fluidized bed reactors. The presence of cuprous ferrite due to reducing conditions inside individual particles also occurs, but in very limited extent at the reaction interface, as it is demonstrated by the low soluble iron levels of calcines. On the other hand, the presence of cupric ferrites can be explained only due to the higher temperature achieved by particles, since below 680°C cupric ferrite formation does not take place. [ ] This phenomena also occurs for others non-ferrous metal sulphides concentrates roasted under sulphation conditions, such as 7n, Co and Ni. Therefore the prediction of discharge composition of fluidized beds is not possible based only on kinetics and mechanistics models alone or purely thermodynamical considerations, since all factors should be integrated to describe the overall phenomena. SINGLE PARTICLE TRANSFORMATION Assuming a first order reaction with respect to the gas and zero for solid, such as

Jan 1, 1984