Search Documents

By Mika Muinonen

"Dewatering of nickel concentrate at the INCO Thompson integrated mine-metallurgical site takes place within the smelter plant. The eight original 60 foot diameter cable torque thickeners of which four were operational and eight Dorrco internal drum filters have been replaced with a single Outokumpu high rate thickener and a single Lasta pressure filter. The modernization has resulted in a filter cake which has a more stable and lower moisture content. Control of the entire dewatering process has been improved and costs have been reduced.Typical filter cake produced from the Dorrco filters during processing of high tonnages of Birchtree mine ore was ~20% moisture vs. ~13% moisture for concentrate produced from the Thompson mine ore. The high moistures were correlated with the amount of fine magnesium silicate gangue in the concentrate. As Birchtree ore processing rates have increased, this filter cake moisture became unacceptable because of material handling problems and the impact on furnace metallurgy. The Dorrco filters were replaced with the Lasta filter in 2003 that has consistently produced filter cake at ~11% moisture.This paper summarizes the piloting, design, installation and commissioning of the modernized dewatering circuit.INTRODUCTIONThe Thompson integrated nickel processing facility was built in 1958 and originally consisted of a mine-mill-smelter and, soon after, a refinery.Nickel concentrate is pumped from the mill as a dilute slurry directly to the smelter facility ~200 meters along an unheated pipe trestle. Originally, nickel concentrate was de-watered using up to 8 conventional 60-foot diameter thickeners and 8 internal vacuum drum filters."

Jan 1, 2006

By N. Shi, T. G. Joseph

The design of dippers for cable shovels has essentially remained unchanged for the last 100 years. In the past 10 years, shovel manufacturers have started taking another look at dipper design, resulting in changes that have borne models from major manufacturers that address some of the wear conditions and material retention problems that dominate maintenance and operational costs. However, with the exception of added lateral curvatures to the front and corners of the dipper, the geometry is essentially unchanged. This paper looks at the criteria that have resulted in the first new cutting dipper design in a century. The design is based on kinematic considerations, reflected in a revolutionary geometry that matches the range of motions of the shovel, designed to minimize wear, impact loading and power required to dig, thus maximizing productivity for a minimum energy requirement. The shape configuration is such that the weight of the dipper is reduced through wall thickness, enabling a larger capacity dipper to be conceived for the same shovel. Benefits are reflected in reduced operational and maintenance costs and increased productivity.

Jan 1, 2006

By Xi Zhang

A technique for fabricating free-standing, high-aspect-ratio porous and pillar-type Ni structures has been developed using wet Si processing. A wafer of (100) Si was initially etched in HF solution to form deep pores with micron-sized diameter. The aspect ratio can exceed 200. By introducing the as-etched Si into a defined aqueous Ni2+ solution, Ni deposits grew rapidly onto the sidewalls and replaced the Si. Long-time immersion allows the Si sidewalls to be completely converted and thus form a metallic Ni structure with high-aspect-ratio pores. It is known that close-packed submicron Si pillars can be formed by oxidizing and subsequent etching of the macropore sidewalls. Treated in the same Ni solution, high-aspect-ratio Ni pillars were correspondingly emerged by replicating the original pillar-type Si structure.

Jan 1, 2006

By A. L. D. Skury

In the synthesis of diamond, the precursor graphite must present a degree of crystallinity to assure optimum yield and quality for the transformed crystals. X-ray diffraction, SEM and TEM analyses were carried out to investigate the structural and morphologic transformations produced in natural graphite by high pressure-high temperature treatment. The present study had as its objective to characterize the morphological and structural changes suffered by a natural graphite that was subjected to high pressure and high temperature treatments in the region of diamond thermodynamic stability. The results indicate that the material that constitutes the gasket, for the deformable capsule, could act as catalyst in the graphite recrystallization process.

Jan 1, 2006

By V. Coetzee

Keywords: Pyrometallurgy, furnace, PGM, platinum, nickel, copper, electric smelting, six-in-line, Peirce-Smith, Impala Platinum In 1992, a paper was compiled highlighting a common-sense approach to electric smelting at Impala Platinum. Since then, the smelter complex has undergone considerable changes. Mineral economics, UG2 exploitation, and changing environmental legislation have enforced numerous process upgrades, yet a common-sense approach has always been adopted. This document details the major changes in the smelter complex at Mineral Processes (Minpro) over the past 15 years, and provides the rationale for the changes.

Jan 1, 2006

By B Mil, D P. Adhikary, M S. Craig, P Rutzou

As shallow coal reserves with easier mining conditions are exhausted, future deep coal mining with difficult mining conditions may face significant economic, technical and environmental challenges. Moreover, due to increased coal production capacity with the new generation longwall systems, predicting adverse mining conditions has become more important than ever before. The potential impact of these difficult conditions is an increase in mining risks and costs. Reliable prediction of rock mass deformation, mine stability and mine water inflow is not only essential for improving mine safety and reduction of coal production costs, but it is also important for the assessment and management of the environmental impact of mining. This paper briefly describes an integrated approach to mine groundwater simulation and prediction. Central to this integrated approach is a three-dimensional computer code called COSFLOW, developed by CSIRO of Australia in collaboration with NEDO and JCOAL of Japan to address the pressing issues of mine water management. COSFLOW incorporates unique features that make it ideal for the simulation of coal mining and examining the interaction between rock fracture, aquifer interference and water flow. This paper also presents an example of an application of the integrated approach and COSFLOW in water inflow prediction at Springvale Mine in New South Wales.

Jan 1, 2006

By Ross Nairn

"Tulawaka Mine is a joint venture between Pangea Minerals Limited 70% (a wholly-owned subsidiary of Barrick Gold Corporation) and Northern Mining 30%. Tulawaka Mine is located in North West of Tanzania in the Lake Victoria Goldfields. Tulawaka Mine is scheduled to process 360,000 tonnes per year at an average 11.5 g/t head grade over a 4 year mine life.The Tulawaka Process Plant uses single stage crushing, single stage SAG milling, gravity, intensive leach of gravity concentrates, CIL, Zadra desorption and cyanide detoxification to process the ore. Gold recovery exceeds (or is expected to) 95%.The Process Plant was designed and constructed under the supervision of Ausenco Engineering of Australia. Site works commenced in January 2004, Process Plant construction commenced in July 2004 and the first ore was presented to the Process Plant 26th February 2005. The first gold was poured on 15th March 2005. All construction contractors were demobilized from site 7th April 2005. Major achievements have been 3.4 million hrs LTI free during construction and operation to date, training of the Tanzanian workforce at Bulyanhulu Mine prior to commissioning, a succession plan to replace expatriate personnel with Tanzanian staff and significant over performance of the Process Plant against design.INTRODUCTIONTulawaka Mine is situated approximately 160 km south west of Mwanza in the western Lake Victoria Goldfields District of north western Tanzania. The property is held under a joint venture between Pangea Goldfields Inc (70%), a wholly owned subsidiary of Barrick Gold Corporation, and Explorations Minieres Du Nord Ltée (30%). A location map showing the position of the operation in Tanzania is shown in Figure 1.Mine site staff at Tulawaka comprises a combination of Tanzanian and Expatriate personnel. All Pangea personnel live on site and commute to their place of residence for their R&R on a 9 weeks on 4 weeks off roster."

Jan 1, 2006

By Bowen Li

Silicon Carbide is an excellent refractory material. Its physical properties make it extremely useful, particularly in applications where corrosion resistance and wear are important considerations. Commercial silicon carbide refractory is frequently manufactured by bonding silicon carbide particles with clay; however, clay may cause problems in the sintered products. This study investigates the potential of replacing a portion of the clay with andalusite powder. The results show that micron size andalusite powder can improve not only the strength of the refractory but also the sinterability. The mechanisms for these improvements are discussed.

Jan 1, 2006

By N. Shariatmadari

In recent years, determining bearing capacity of piles from in-situ testing data as a complement of static and dynamic analysis has been used by geotechnical engineers. In this paper, different approaches for estimating base bearing capacity of piles from SPT data has been compared and evaluated. A new method for pile base bearing capacity in sand is proposed using SPT records. Data averaging, failure zone extension, and plunging failure of piles have been addressed in the proposed approach. A data bank comprising 10 full scale static load tests on instrumented piles and 26 dynamic tests, analyzed with signal matching technique by CAPWAP software, was used for validation. The SPT data that was performed close to pile locations is also included in the data base. Comparison of current methods by error investigation with Log-Normal approach demonstrates that the proposed method predicts pile base capacity with more accuracy and less scatter in comparison to other methods.

Jan 1, 2006

By Frances Badelow

This paper describes a design process for piled raft foundations supporting high-rise buildings. The design process comprises an initial stage of geotechnical site characterization using the results of investigation boreholes to prepare a subsurface model and derive geotechnical parameters for raft and pile design from empirical correlations. Following this a preliminary analysis is undertaken using a combination of elastic theory and allowances for non linear behaviour of the piled raft system to assess the viability of such a foundation system and any potential advantages of a piled raft over conventional fully piled foundation systems. Finally, a detailed analysis is undertaken using the GARP8 computer program. Case studies where this design process has been successfully used to design a more efficient piled raft system that has resulted in significant cost and time savings compared to conventional bored pile foundation options are also described.

Jan 1, 2006

By Phillip M. Dight

A number of impending and actual pit wall failures have been observed and documented which have been interpreted to initiate on newly generated structural features. This infers failure through intact rock. Failure mechanisms have been postulated resulting from circumferential stress, extensional strain and brittle flexure. These will be discussed in the context of the failures and the associated monitoring. The implications of failure initiating on ?unknown? features has a significant impact for deep open pit mines where designs are based on the expected structural regime. Being able to anticipate such failures is important for design. Equally important is management of such changes as they arise. In this context, monitoring using high resolution microseismic techniques will be discussed as a means of providing early warning of such failures.

Jan 1, 2006

By Emmanuel N. Zevgolis

Energy required for roasting and smelting of a nickeliferous laterite ore by the rotary kiln - electric furnace process is investigated. From this work it comes that thermal energy is about 65% of the total energy needed and the rest is electrical. Also, 61.3% of thermal energy input in the roasting step (of all combustibles fed into the rotary kilns) is used for pre - heating, 11.6% for pre - reduction and the rest (27.1%) corresponds to the energy of the remaining carbon in the rotary kiln products (i.e., calcine, dust and coatings). Carbon entering the system is used as follows: 57.9% for combustion, 37.1% for reduction and the rest (5.0%) remains unburnt. Exploitation of energy from gases of both furnaces, as well as the higher possible reduction degree, the optimum temperature of the calcine and also elimination of the excess air in the rotary kilns, improve significantly energy balance and economics of the process.

Jan 1, 2006

By Joseph J. Feiler

Historical mining operations in Colorado and other western states have resulted in thousands of remnant mine openings. Many are sources of metals loading and acid water generation in surface and ground waters. It is estimated that more than 965 km (600 miles) of streams in Colorado have been impacted by past mining activities. The Animas River watershed in southwestern Colorado is one of the most heavily affected areas in the state. Abandoned mine features pose significant safety hazards to those who enter them. These hazards can include bad air, unstable rock or falls into open shafts, stopes and winzes. Backcountry skiers and snowmobile enthusiasts are particularly vulnerable to falls into snow covered mine openings.

Jan 1, 2006

By Michael P. Sudbury

Non-ferrous slags are granulated and stockpiled as an alternative to pit cooling or transporting molten slag to a dump. The chemical composition of such slag is determined by the pyrometallurgical process in which it is produced, while the size distribution is set by safety concerns or a desire to reduce wear of pumps, pipelines and other equipment. Relatively few operations give consideration to the effect of granulation conditions on other properties of the granulate as the material is typically accumulated on the smelter site. It is becoming recognized that slag has many potential commercial uses and carries much of the energy applied to the smelting operation. This paper outlines the findings of extensive work to identify uses for granulated non-ferrous slag, the importance of preparation conditions on the properties, impediments to more extensive use of granulated slag, the real costs of slag stockpiling and the opportunities for further productive research.

Jan 1, 2006

By P. A. Plunkert, D. E. Morse, L. McCartan, J. F. Papp

The mineral sector is a fundamental part of the U.S. economy. It contributes to the real gross domestic product (GDP) at several stages —basic (mining), intermediate processing, manufacturing of finished goods and construction. The real GDP increased by 3.5 percent from 2004 to 2005. The nominal GDP was $12.5 trillion at the end of 2005. Housing starts were up by more than 5 percent for the year, and the unemployment rate decreased to 5.1 percent in 2005 from 5.5 percent in 2004. The prime interest rate increased from 5.25 percent at the beginning of the year to 7.25 percent at the end of the year. The value of minerals mined in the United States in 2005 rose significantly because of increased unit prices for some metals —particularly molybdenum — and significantly increased production for some industrial minerals, mainly cement, construction sand and gravel, and crushed stone.

Jan 1, 2006

By J. MacFadyen

The U.S. cement industry, including Puerto Rico, again set a record in terms of production and shipments. The increase in shipments came primarily from imports of portland cement as domestic production from produced and imported clinker gained only 1.9 Mt (2.1 million st). Clinker production as reported to the U.S. Geological Survey (USGS) was 88.6 Mt (97.6 million st), an increase of 1 percent. Gray and white portland cement production from domestic and imported clinker, estimated at 93.5 Mt (103 million st), was up 1.9 Mt (2.1 million st). Masonry cement shipments of 5.5 Mt (6 million st), which equates closely to production, was up 6.3 percent. Blended ce-ment shipments were up 35.9 percent from 2004 at 2.35 Mt (2.6 million st).

Jan 1, 2006

By Dominic Fragomeni, Tony DiFeo, Martyn P. Hay

"As part of an investigation into flotation modelling of industrial scale operations, Falconbridge Ltd organised a “blind” test of the SUPASIM flotation model developed by Eurus Mineral Consultants (EMC). Two sets of rougher rate data, a flowsheet and the number and size of cells in the rougher bank were supplied from a plant that had been previously surveyed in November 2003. The name of the plant, cleaner circuit details and circuit mass balance were, at the time, unknown to EMC. With only these data, flotation performance was simulated and the cleaner circuit sizedFalconbridge then compared predicted and actual float performance and mass balance and found that final concentrate recovery and mass and circuit cell volume matched closely. Simulated recoveries relative to actual were +0.4% Cu, +0.1% Ni and -0.7% Co. However, prediction of metal distribution in the internal streams making up the various circulating loads showed some sizeable errors. On this initial success, the trial was extended and additional float test data for rougher feed, cleaner feed and cleaner scavenger feed was generated on site in April 2005. Further simulations significantly improved prediction accuracy for metal distribution in the internal streams. The average difference between predicted and actual recovery for all streams was reduced from 10.5% to 0.4%. This updated simulation was then used to ascertain the impact on final recovery, grade and plant circulating loads of increasing feed tonnage from 114 to 150t/hr. A number of scenarios were simulated in order to understand the contribution that (a) the fast and slow floating fractions and (b) regrinding of cleaner tailings are making to overall plant recovery.Simulation was then used to determine how much the flotation kinetics of both rougher feed and cleaner scavenger feed have to increase in order to deliver a 1.5% improvement in overall plant recovery. These improved kinetic values provide a target for laboratory testwork and operating conditions can be varied to determine how best to achieve these new values of fraction and rate."

Jan 1, 2006

By Fred N. Kissell

This handbook describes effective methods for the control of methane gas in mines and tunnels. It assumes the reader is familiar with mining. The first chapter covers facts about methane important to mine safety, such as the explosibility of gas mixtures. The second chapter covers methane sampling, which is crucial because many methane explosions have been attributed to sampling deficiencies. Subsequent chapters describe methane control methods for different kinds of mines and mining equipment, primarily for U.S. coal mines. These coal mine chapters include continuous miners and longwalls, including bleeders. Coal seam degasification is covered extensively. Other coal mine chapters deal with methane emission forecasting and predicting the excess gas from troublesome geologic features like faults. Additional coal chapters contain methane controls for shaft sinking and shaft filling, for surface highwall mines, and for coal storage silos. Major coal mine explosion disasters have always involved the combustion of coal dust, originally triggered by methane. Thus, a chapter is included on making coal dust inert so it cannot explode. Methane is surprisingly common in metal and nonmetal mines around the world, as well as in many tunnels as they are excavated. Accordingly, a chapter is included on metal and nonmetal mines and another on tunnels. Proper ventilation plays the major role in keeping mines free of hazardous methane accumulations. The ventilation discussed in this handbook, except for the chapter on bleeder systems, deals only with so-called face ventilation, i.e., ventilation of the immediate working face area, not ventilation of the mine as a whole. The omission of whole-mine ventilation was necessary to keep this handbook to a reasonable size and because a huge amount of excellent information is available on the subject.2

Jan 1, 2006

The purpose of this study was to investigate the immobilization as a host for metallic pollutants (Cr, Cu, Pb, and Zn) by ettringite phase. Ettringite phase is produced through hydration reaction of calcium aluminate with gypsum. From the XRD patterns, it is known that the distance between spaces in 010 planes in ettringite crystal increase with an increase of ionic radius of heavy metal except Pb; no big difference is shown. For this reason, the d-value of 010 planes in ettringite crystal increased with the substitution of Cr, Cu and Zn having a big Al ironic radius. But in case of Pb, because the substitution occurred at calcium site, it does not influence to increase d-value of 010 planes.

Jan 1, 2006

By Lifeng Zhang

The transport of fluid, heat ,and particles (bubbles and solid inclusions) in flowing molten steel is investigated in steel refining ladles, the continuous casting tundish, continuous casting mold and strand, and steel ingot casting processes. The two-equation k-?? model is used to simulate the turbulence. Multiphase fluid flow is numerically simulated with a Lagrangian-Eulerian approach, an Eularian-Eulerian approach and the Volume Of Fluid (VOF) method. The simulation can predict inclusion trajectories, inclusion removal fraction, free surface waves and other phenomena, which can be used to optimize these important metallurgical operations.

Jan 1, 2006