Search Documents

By I. F. Jackson, H. L. Hartman

Hard-metal inserts have received considerable attention in the mining industry recently for a variety of excavating and penetrating purposes. Their use in percussive drilling and in coal cutting machines is well known, but attempts to utilize them in cutting materials such as dimension stone have been discouraging because of excessive tool wear and failure. Particular attention is given to those properties of hard-metal inserts that affect their resistance to wear. A consideration of the actual wear mechanism shows the importance of correct mounting of the inserts and of the selection of suitably powered driving motor so as to achieve minimum tool wear and maximum tool life. Comparisons are made between the performances of types of hard-metal inserts, relating their inherent properties with results obtained in laboratory tests. As part of a broad program to improve the quarrying and processing of industrial minerals, The Pennsylvania State University has been investigating the machinability of slate under laboratory and field conditions. It should be emphasized that the results of the research presented in this paper are also applicable to other natural structural materials, and particularly to the more workable ones such as limestone and sandstone. Improvements which accrue in cutting and sawing should prove of benefit to all the dimension stone industry. Further, it may be pointed out that the results reported here are applicable to rotary drilling (with drag bits) as well as to cutting and sawing of rock. INVESTIGATIONS IN RELATED FIELDS The investigation was initiated with an extensive survey of available literature related to metal cutting and to rotary drilling. The following similar features between metal cutting and slate cutting became evident: 1) Hard-metal inserts are widely used as a cutting tool in both cases. 2) The forces acting on the tool may be resolved into normal and tangential components. 3) Rate of penetration and tool wear are important criteria in each case. On the other hand, important differences also exist: 1) Most metals, exhibit plastic behavior, while slate (and most rock) is a brittle material under normal conditions. 2) In metal cutting the component of force acting parallel to the surface of the workpiece is considerably greater than the force holding the tool against the workpiece. 111 slate cutting, this situation is reversed. Similarities between drag-bit rotary drilling and slate cutting are as follows: 1) In both casts, a tool, usually of the hard-metal insert type, is used to penetrate a brittle material. 2) The drilling forces and related variables, such as rotation speed, are similar. 3) Chip formation in each case is essentially the same. 4) The shape of the tool is similar in rotary drilling and slate cutting. Important differences are also apparent: 1) The objective of drilling is to produce a directed hole, while in cutting it is to form a kerf. In core drilling, however, a kerf is also produced. 2) The horizonta1 component of force in rotary drilling decreases from the center to the outside of the tool, whereas in slate cutting the component is almost uniformly distributed across the width of the tool. 3) The power absorbed in the drill rod is greater in rotary drilling. 4) The clogging action of chips, if excessive power is applied to the tool and if flushing is insufficient, is more serious in rotary drilling. Because of the striking similarities between metal cutting and slate cutting, and between rotary drilling and slate cutting, it was considered that the findings of investigators in those fields would serve as a guide for experimental studies of slate cutting. The following is thus devoted to a discussion of those aspects of metal cutting and rotary drilling pertinent to the present investigations.

Jan 1, 1962

By E. Eichen, G. S. Ansell. L. R. Sefton

A Technique for the Preparation of Thin Films of Two-Phase Alloys Suitable for Use in Transmission Electron Microscopy In order to obtain foil sufficiently thin to permit transmission electron microscopy of two-phase alloys, particularly alloys in which the second phase is present as a very finely dispersed second phase, a technique has been developed to permit the thinning of these materials without either the large degree of pitting present in the electrochemical or chemical thinning process or the slicing of the second phase particles accompanying the mi-crotoming process. The metal or alloy to be thinned is first ground to initial sheet thickness of approximately 0.002 in. by hand grinding on 4/0 emery paper. This starting sheet of material is then reduced in cross section by an air-abrasion technique using an S. S. White dental abrasive unit. This unit consists of a supply of compressed CO, which provides a stream of high velocity gas impinging on the metal surface. Incorporated in the machine is a hopper-type of device in which fine abrasive particles of alumina are introduced into this high velocity gas stream. The abrasive particles are irregular in shape, approximately 30 across. If any particles are introduced into the sample during thinning, they should be readily observable. Impingement of this gas abrasive mixture on the metal surface causes rapid removal of the metal in a rather uniform manner. The rates of metal removal may be adjusted by both regulating the gas pressure and amount of abrasive material introduced into the gas stream. By moving the gas stream abrasive mixture slowly about the specimen or sheet surface, a large area of the sheet may be uniformly reduced to a thickness which is then suitable for use in transmission electron microscopy. Attendant with this metal removal is a result in cold working of the metal surface due to the impingement of the abrasive particles. The resultant foils, therefore, if made from materials which are desirable to view in the annealed condition, have to be subsequently heat treated. If the alloy from which these foils have been made has been initially heavily worked or deformed during manufacture, then no subsequent heat treatment is, necessary as in the case of the SAP-type alloys. Following this initial abrasive thinning technique, the material is then given a final electropolish which is just sufficient to remove any oxide which has formed on the metal surface during the abrasion technique. Care has to be exercised in this technique to make sure that none of the attendant problems associated with the chemical or electrochemical removal process are encountered. An electrolyte solution which has been found suitable for aluminum-aluminum oxide SAP materials is one containing 78 ml of perchloric acid, 120 ml of distilled water, 700 ml of ethanol, and 100 ml of butylcellosolve. The current density used is 1 amp per sq cm and a polishing time of 3 sec on each side of the foil is used. Extreme care must be used in choosing the current density and time to ensure that just the oxide film on the specimen is removed. Times or current density which are greater than this will lead to perforation of the film due to the removal of the A1,0, particles or a complete loss of the film due to complete solution of the matrix. Once the oxide film is removed the specimens must be kept in alcohol until placed in the microscope to prevent any further oxidation. Fig. 1 shows -an electron micrograph at X28,000 of a thin foil of an aluminum-aluminum oxide SAP-type alloy prepared using this technique. The alloy consists of a matrix of commercial purity aluminum containing a very finely dispersed second phase of aluminum oxide flakes. In the electron micrograph, the dark patches are the aluminum oxide particles. The lighter portions of the micrograph are the aluminum matrix. Within the aluminum matrix, the dislocation structure of the alloy is clearly visible. This structure consists of intersecting twin boundaries and single dislocations. No abrasive particles were observed in the samples. In addition, thin films of commercial purity aluminum were prepared using this method and observed in the electron microscope. Here also, there was no evidence of abrasive particles introduced in the samples. The technique presented provides a satisfactory method for the production of thin films of aluminum-aluminum oxide SAP-type alloys for use in transmission electron microscopy where none of the usual thinning techniques appears to be satisfactory.

Jan 1, 1962

By E. S. Machlin

An extension of the thermodynamic theory has been made for the case of irreversible growth processes occurring by the motion of an interface. The theory is applicable to such diverse phenomena as diffusion, growth in recrystallization, continuous grain growth, growth of carbides, etc., growth of eutectoid products, growth in solidification, recovery, "slipless" flow, etc. THE publication of a recent book1 has served to focus attention on a very powerful means of treating certain irreversible processes. This method which has been formally described as the thermodynamic theory of irreversible processes is applicable to processes which involve an approach to equilibrium and for which the deviations from equilibrium are small. The irreversible processes can be classified into three groups: chemical reactions, transport processes (diffusion, heat and electrical flows), and relaxation phenomena involving a degradation of internal energy to more stable states. The limits of applicability of the theory can be precisely defined1,2 for each type of irreversible process. For example, in a chemical reaction at constant temperature and pressure, the Gibbs free energy released per mol in the process should be less than the thermal energy, RT. Another type of irreversible process, which sometimes involves a combination of the first two of the above-mentioned groups, is treated in this paper. This process is one characterized by the motion of an interface separating two regions having different values of free energy and may be briefly described as a growth process. Prigogine2 and Herring3 have treated special cases of this type of process. Previous conscious applications of the theory in metallurgy have been limited to the field of diffusion, one of the transport processes. Darken,4 Bardeen,5 Prigogine2 and others have made significant contributions in this respect. Some other applications of the theory are described in this paper. The Theory The thermodynamic theory of irreversible processes is based on the work of Onsager,6 DeDonder,7 Prigogine2 and others. A resume of the theory has been given by Prigogine2 and DeGroot.1 A brief description of the theory follows, although for a complete understanding the reader is urged to read the references. It is first assumed that the change in entropy, even for a system removed from equilibrium, is given by dS = [dU + pdV - Si µi, dn, - Sk Pk dxk]T-1 Using this expression, the irreversible entropy production in the system is calculated by subtracting the contribution to the change in entropy of the system by transfer of heat, work, or matter from the surroundings. Thus, for example, the irreversible entropy production of a system at constant temperature and pressure is given by dtS = — — dG (DeDonder7) Now it has been shown by Prigogine,2 DeDonder,7 and DeGroot1 that the rate of irreversible entropy production diS/dt, when calculated in the manner suggested, can be written as a sum of products of conjugate forces XK and fluxes Jk, i.e., d,s/ = Sk Jk Xk [I-1] dt The assumption is next made that a linear relation exists between a given flux and the forces, obtained from Eq. I-1, i.e., Ji = Sk Lik Xk (i = 1, 2, . . . n) [I-2] Generally, there is a degree of freedom in choice of the fluxes and forces. However, for all the choices consistent with Eq. I-1 the Onsager8 relations, based on the principle of microscopic reversibility, namely, Lik = Lki, are valid. The coefficients Lik, depending upon the choice of the conjugate fluxes and forces, may be more or less dependent upon the parameters defining the state of the system. In general, the proper choice of fluxes and forces utilizing Eq. I-1, makes the coefficients Lik independent of time. Also, because many of the three classes of irreversible phenomena have already been treated,1,2 a proper choice can be made by analogy. In any case, the validity of Eq. 1-2, from whatever choice made using Eq. I-1, must be tested by experimentation. The theory, thus, comprises the following steps: 1—The irreversible entropy production is calculated to yield Eq. I-1. 2—The terms in Eq. I-1 are grouped

Jan 1, 1954

By E. F. Johnson, F. H. Brinkman, H. J. Welge, S. P. Ewing

This paper presents a method for predicting the manrler in which oil will be displaced from a porous body by enriched gas. The calculations apply to a gas rich enough to give a partially, but not a completely, misci-ble displacement. The method — a three-component, two-phase analysis — takes into account condensation of some of the intermediate hydrocarbons from the injected gas into the oil, as well as enhanced volatility of heavier hydrocarbons at elevated pressures and temperatures. The condensation swells the oil and decreases its viscosity, thus aiding in its recovery. The calculations have been extended to apply to actual crude oil-natural gas systems by arranging the components into three groups according to their volatility. As an approximation, each group is then treated as a single component in the analysis. The influence of an angle of dip for an inclined displacement is also taken into account. The recovery predictions are corroborated by experiments which used both consolidated sand cores and un-consolidated glass beads. In some of these tests, actual live crude oil was displaced by a multicomponent gas typical of enriched gases used in oil fields. INTRODUCTION This paper presents a method for predicting the amount of oil that can be displaced from a homogeneous, linear, porous body at various stages during the injection of enriched, or "wet", gas. The porous body can be in either a horizontal or an inclined position. 'This type of displacement is sometimes known as condensing gas drive The method is developed especially for the case in which the injected gas is enriched enough to be partially, but not completely, miscible with the reservoir oil. The need for a calcula-tive procedure for this type of operation is emphasized by the number of field projects where completely miscible drives are not practical, but where near-miscible conditions are feasible. The factors taken into account in the predictive calculations include: (1) the condensation of gas components into the oil, with a resulting increase in oil volume; (2) the lowering of oil viscosity by the addition of lighter ends from the gas; (3) the increase in oil volatility at high temperatures and pressures; and (4) the physical displacement of the oil by the gas. The techniques developed in the paper can be extended to other nonequilibrium displacement processes. Other such processes that we have analyzed include a displacement by lean gas which stripped intermediates from the oil, and a water flood in which the water con. tained in solution a substance somewhat soluble in the oil. ANALYSIS OF ENRICHED-GAS DRIVE GENERAL PRINCIPLES Our method for predicting the amount of oil that can be displaced by an enriched gas uses an analogy between a three-component and a multicomponent system.' The predictive method is based on these assumptions: (1) constant, or nearly constant, pressure; (2) complete equilibrium by diffusion perpendicular to the main direction of flow, but no significant mixing along the direction of flow; (3) constant injection velocity; and (4) flow in a linear porous body. The composition of a liquid or a vapor with respect to three components can be plotted on a three-component, or ternary, diagram like that in Fig. 1. Let Point A represent the composition of the oil originally in place. In this case, Oil A is undersaturated with gas. If Point A lay on the equilibrium Curve BF, the oil would be saturated. In the extreme case where the original oil contained no intermediates or dissolved gas, Point A would lie at the lower left-hand corner of the ternary diagram. In a displacement of Oil A by Gas D, there will be a progressive change in the composition of the oil phase as more and more gas is brought into equilibrium with the oil. The end result of this progressive change is an oil having the composition represented by Point F. This oil is richer in intermediate hydrocarbon and methane than the original oil and, therefore, has a greater forma-

By Joseph C. Mead, Alan Stanley

The MacIntyre Development of the National Lead Co. is located at Tahawus, N. Y. The operations involve the mining and concentrating of a titaniferous iron ore to produce an ilmenite concentrate and a magnetite concentrate. Construction of the MacIntyre plant was commenced during the summer of 1941,when world conditions threatened to cut off the supply of Indian ilmenite. An open pit mining operation was developed and the crushing and milling equipment put in operation in July 1942. A general description of the operation was given in the Adirondack Issue of Mining and Metallurgy for November 1943. The metallurgy of the mill operation was described by Mr. Frank R. Milliken,* Plant Manager, National Lead Company, MacIntyre Development, and presented at the AIME New York Meeting, February 1948. The magnetite concentrate produced in the milling operation was too fine (minus 20 mesh) to be used directly in iron blast furnace operation, and most of the magnetite had to be stockpiled in 1942 and 1943. In 1943, the Defense Plant Corp. built a Greenawalt sintering plant at Tahawus, N. Y., to put the magnetite concentrate in a more suitable form for use in the iron blast furnace. The Greenawalt sintering plant consists of three 10 by 25 ft sintering pans designed to produce 1800 gross tons of sinter per 24 hr. The vacuum to each pan is produced by two Greenawalt fans in series, pulling approximately 30,000 cu ft of air per minute at 50 in. water gauge vacuum. The plant started operation in August 1944. The present plant production averages 25 tons per operating pan hour (approximately 224 lb per operating hour per square foot of grate area) of plus 1 in. sinter. Raw feed to the plant consists of 61 pct magnetite, 4 pct anthracite coal culm, and 35 pct minus 1 in. return fines which are conveyed to a pug mill where the materials are mixed thoroughly and water added to give the mixture 5.5 to 6 pct moisture. The mixed prepared feed is conveyed to two 4 by 10 ft vibrating screens where the minus 1 in. plus 5/8 in. return fines are screened out and discharged into a surge bin for use as a hearth layer. The minus 5/8 in. prepared feed is discharged into another surge bin for use as prepared feed. A charge car, electrically operated, having a capacity of one charge of prepared feed and several charges of hearth layer, lays a thin layer of plus 5/8 in. return fines and 9½ in. depth of prepared feed into the pans. A fluffing roll and a vibrator on the car fluffs and spreads the prepared feed into the pans. An ignition car, electrically operated, ignites the top of the bed with a 30 sec flash burn. The 9½ in. bed sin-ters in approximately 13 min. Dumping the pan, and recharging and igniting the bed requires 2 min. To improve the quality of the ilmenite concentrate produced in the mill and to reduce the amount of titanium dioxide lost in the mill tailings and in the magnetite product, extensive research work and pilot plant operations have been done on grinding the crude ore to minus 65 mesh size (rather than to minus 20 mesh) and concentrating it by a combination of magnetic separation (for magnetite recovery) and flotation (for ilmenite re-covery). These tests have proved successful in increasing ilmenite re-covery and grade. With the development of the ilmenite flotation process to a stage where a full scale flotation plant was in the design stage, the problem arose of handling the 65 mesh magnetite concentrate that would be produced. In order to study and solve the problems of handling and sintering the 65 mesh magnetite in the sinter plant, a pilot sinter plant was secured from John E. Greenawalt. The effect of using 65 mesh magnetite in the sintering operations was then studied on the 2.4 sq ft test pan, operating under conditions as similar to the large plant as could be set up in the laboratory. A series of tests were run in the test pan on present sinter plant feed that had been mixed in the plant pug mill. An average production and an average quality of sinter produced in this series

Jan 1, 1950

By F. V. Lene, E. J. Westerman

The recrystallization behaviors of two extruded and cold-drawn experimental sintered aluminum powder alloys, containing 1.75 and 3.0 pct Al2O3 by weight, were compared with that of extruded and cold-drawn commercially pure alumirzum. The kinetics of recrystallization of the alloys are described semiquantitatively. For the alloy containing 1.75 pct A l203 the rates of nucleation and of growth were also semiquantitatively determined. THE most striking property of aluminum alloys strengthened by a dispersion of Al2O3, the so-called SAP alloys, is their stability at elevated temperatures. One of the manifestations of this stability is their resistance to recrystallization after they have been cold worked. Most of the commercial grades of either the Swiss SAP or of Alcoa's Aluminum Powder Metallurgy Products have not been recrys-tallized after cold working, even when they are heated for a long time at a temperature near the aluminum melting point. Lenel, however, observed that the dispersion strengthened aluminum alloys with a larger spacing between the oxide particles than that of most commercial grades would recrys-tallize.1 It appeared to be of interest to further investigate the mode and kinetics of recrystallization of these alloys, and to compare their recrystallization behavior with that of commercially pure aluminum. Because homogeneous deformation of these SAP alloys in tension did not provide sufficient cold work to induce recrystallization, they were cold worked by wire drawing; the nonuniformity of this deformation unavoidably complicated the interpretation of the recrystallization studies. EXPERIMENTAL DETAILS Extrusions—Two types of sintered aluminum powder extrusions were used in this study. One type, designated AT-400, was produced from Reynolds atomized aluminum powder consisting of spherical particles averaging 3µ in diam and containing 1.75 wt pct of Al2O3. This powder was very similar to the R3M powder from which extrusions were previously prepared with an average spacing of 0.9µ between oxide particles.2 The second type, designated MD 2100, was produced from Metals Disintegrating Co. flake powder containing 3.0 wt pct of Al2O3, with an average flake thickness of 0.8µ. The average spacing between oxide platelets in MD 2100 extru- sions was 0.45µ.2 Powder compacts of 3/4-in. diam were extruded at 1000°F into 0.097-in. diam (AT-400) and 0.093-in. diam (MD 2100) wires by methods previously described.3 In order to compare the recrystallization behavior of sintered aluminum powder extrusions with that of wrought commercially pure aluminum 3/4 in. rod stock of 1100 F aluminum was extruded at 1000°F into 0.102-in. diam wire. Wire Drawing—Tungsten carbide dies were used for the AT-400 and 1100 F alloys. They had an included angle of about 15 deg and reduced the wire area approximately 7 pct per pass. Steel dies with an included angle of 11 to 13 deg and an average reduction per pass of 10 pct were used for drawing the MD 2100 alloy, because drawing this alloy through the carbide dies produced overdrawing defects. Heat Treatment—The cold-drawn wires were cut into small samples, and the deformed ends were etched off. The samples were each wrapped tightly in a single layer of aluminum foil, and individually isothermally annealed in a lead bath. Metallography—The modes and kinetics of recrystallization were determined by metallography. Mounted and polished specimens were anodized in a solution of 1.8 pct HBF4;4 examination under polarized light clearly revealed their grain structures. The recrystallized grains were generally much larger than those of the unrecrystallized matrix, and could clearly be distinguished because they alternated between maximum and minimum light reflection when the microscope stage was rotated, while the unrecrystallized matrix had a comparatively homogeneous "salt and pepper" structure. The fractional recrystallized volumes of the dispersion hardened alloy wires were determined by cutting and weighing of recrystallized and total transverse areas on photomicrographs. The recrystallized grains in the 1100 F alloy were too small to be cut out individually; therefore a combination of cutting and lineal analysis was used in this case. RESULTS AND DISCUSSION Modes of Recrystallization—The modes of recrystallization of the three alloys varied widely. In the 1100 F alloy nucleation and growth started in the region midway between the center and the surface;

Jan 1, 1961

By R. F. Sheldon

The discovery of the Carlin deposit was the result of discriminating geologic research and prospecting devoted to the objective of finding a gold deposit that could be mined by open pit methods. By the late 1950s, Newmont Mining Corp. was becoming increasingly concerned about the trend of rapidly rising underground mining costs unless bulk mining methods could be applied. The desirability of finding an open-pittable gold deposit was apparent. The attention of Newmont geologists was directed to Nevada by the publication of two papers: "Paleozoic rocks in North-central Nevada" (1958) and "Alinements of Mining Districts in North-central Nevada" (1960), both authored or co-authored by Ralph J. Roberts of the United States Geological Survey. John Livermore, geologist of Newmont Exploration Ltd., attended a talk given by Roberts in Ely, Nevada in the summer of 1961. These papers and the address by Roberts gave details concerning the Roberts Mountain overthrust, a 483 km (300-mile) long, shallowdipping fault which pushed clastic and volcanic rocks of early and middle Paleozoic age eastward over younger marine formations. Subsequent uplift and doming with consequent erosion had locally removed the upper plate strata exposing windows of lower plate carbonate rocks. Roberts noted that the principal mineral deposits of the region, including gold, were associated with these windows which exhibited a preferred alinement. In the summer and fall of 1961 Newmont's exploration geologists John Livermore and J. Alan Coope began a systematic examination of gold occurrences associated with these windows, aided by further discussion with geologists of the US Geological Survey. Attention was directed to the Lynn and Carlin windows, particularly to those formations lying immediately above and below the Roberts Mountain fault. It was appreciated at the time that many of the gold occurrences in the region were unusual in that no colours were obtained even when panning high grade samples. A large number of rock samples were collected and analysed using fire assaying procedures, and background values for gold were established. This systematic rock sampling resulted in the identification of a distinct area of anomalous gold values, and a block of claims was staked in late October, 1961. These claims, plus an adjoining optioned 32.4 ha (80 acres) of ground, cover the main area of the present Carlin gold mine. Prior to snowfall that winter, one of the bulldozed assessment pits required to establish a claim's discovery exposed 24 m (80 ft) of mineralization assaying 0.007 kg/t (0.22 oz per st) gold. In the spring of 1962 a program of trenching, sampling, and geological mapping followed by rotary drilling was underway. Other properties in the area were acquired. The generally undistinguished nature of the dolomitic siltstones and silty dolomitic limestones hosting the micron-sized gold particles, coupled with the lack of visually associated guide minerals, made identification of the gold bearing areas very difficult. The entire drill column had to be assayed to ensure that values were not overlooked, as very often sections that might be assumed to be waste turned out to be high grade. On September 10, 1962 a high grade intersection of 24 m (80 ft) assaying over 0.03 kg/t (1 oz per st) gold was encountered in the third hole drilled. An expanded program of both rotary and diamond drilling led to the further delineation of the ore body. By December 1963, the exploration program had established an initial reserve of 10 Mt (11 million st) grading 0.01 kg/t (0.32 oz per st) gold. A 1.8 kt/d (2,000 stpd) processing plant was constructed and the first gold bullion was poured in May, 1965, just two years and eight months after the discovery hole was drilled. REFERENCES Roberts, R.J., Holz, P.E., Gilluly, J., and Ferguson, H.G., 1958, "Paleozoic Rocks in North-central Nevada," Bulletin American Association of Petroleum Geologists, Vol. 42, No. 12. Roberts, R.J., 1960, "Alinements of Mining Districts in North-central Nevada," Professional Paper 400-B, US Geological Survey, Article 9.

Jan 1, 1985

By David Yob

INTRODUCTION This paper is intended to fulfill three major purposes. The first of these purposes is to narrate the improvements to the ventilation of Northeast Churchrock Mine and the subsequent reduction of the radiation levels. The second major objective is to pass on to persons unfamiliar with the ventilation of radon and radon daughter producing mines some of the most important characteristics of airborne radiation and the control thereof. The third objective is to describe the use of a computerized digital mine ventilation simulation. This description is not only of the usage, but also some of the important methods and techniques involved in the usage. This paper is not intended for the persons with extensive experience in these areas. However, to those persons who are just becoming involved with either ventilation of mines with airborne radiation problems or persons interested in computer simulation, this paper should be of some interest. It is the author's experience that most of the information on either computer simulation or airborne radiation control either assumes an extensive knowledge on the part of the reader, or does not address the direct application of the information contained in these articles. It is for that reason that this paper intends to concentrate on the actual application of the topics covered. INITIAL STATUS In the first quarter of 1980, the author and others became involved with the ventilation effort of the Northeast Churchrock Mine. At this time, this team began an investigation of the mine ventilation with the intent of reperforming a mine pressure survey. During the course of this investigation, it was determined that the ventilation system was inadequate. During this first quarter, the responsibility for ventilation of the mine was transferred to the author and his team. It was determined that the system that was in use was that of the single entry or haulage return type. In this type of system, there is very little direct control of the airflow, and it is not an effective type of ventilation for mines that experience problems due to airborne radiation. In a single entry, or haulage return, system there is no separate return system provided. In the system, as we found it, the only source of intake air to the ore level working areas was from the track level. This intake air was forced into the ore level, or stope level, via bulkhead fans installed on raises from the track. This air, after being used in the working areas, was then allowed to find its own way back to the exhausting vent holes. There was essentially no control of this air from the bulkhead fan discharge to the vent hole. The only control used was by the sizing of the fans on the raises. The main portion of this air used the haulage and access drifting for return. Due to the large horsepower used in these bulkhead fans and the large resistance both between the areas to the vent holes and inadequate intake ducting, the stope level pressure was higher than the track level. This pressure differential caused a severe recirculation between the stope level to the track level. This recirculation also caused a severe pre-contamination problem to the supposedly fresh intake air, making his air nearly unusable for working area ventilation. [ ] It was found at the time our ventilation effort began, that the radiation levels were high enough to make compliance with the four working-level month per year standard impossible. For this reason, we had to spend several months driving costly development drifts to implement a completely different type of ventilation system. Before describing the system that was implemented to solve the problems that were discovered during our initial investigation, some discussion of the characteristics of airborne radiation due to radon and radon daughters is needed. RADON CHARACTERISTICS AND RELATED TECHNIQUES One of the most notable characteristics of radiation contamination caused by radon and radon daughter decay is that once the contamination has entered the airstream, the radiation levels as measured in working levels will continue to rise without any further contamination. This radiation rise will eventually stop

Jan 1, 1982

By William R. Barton

Iron and steel slag represent man's most successful attempt to date to profitably utilize a solid waste. Its consumption represents a solution to a solid waste problem and also represents tonnage of natural aggregates that will not have to be mined with concomitant disturbance of the land. Slag has been produced as long as iron has been made; but until a little more than 50 years ago, it was mostly a waste product to be disposed of with as little effort and cost as possible. Huge piles of waste slag were generated over the years of iron and steelmaking. Sporadic use was found for small amounts starting with slag (from Catalan forges) used for road bases by the Roman Empire. The first recorded sustained commercial use was, as is often the case in man's history, for making war. Some profit- conscious munitions maker in the 16th century realized that he could make cannon balls of slag instead of the more precious iron. Other small-volume uses gradually developed: cast building blocks, slag-lime mortars and cements, slag wool, ballast, road base, and, finally, in concrete. But it was not until after World War II that the true potential of blast-furnace slag as a construction aggregate was really recognized. Now nearly all blast-furnace slag produced is used, and much of the earlier stock- piles in the U. S. have been reduced or entirely consumed. Steel slag for aggregate use has been in commerce for only the past 10 years, and use has increased rapidly (10-50% per year) during the past 5 years as blast-furnace slag supplies became depleted. However, much remains to be accomplished in determining character and optimum conditions of use for various types of steel slags before such slags will realize their full use potential. Although slag represents only 2% of construction aggregate materials used in the U.S., its production involves certain features that make its production record far more important than national tonnage figures would indicate. Its source is in iron and steel production and concomitantly slag availability is restricted to those areas where iron or steel is produced. In such areas, it often represents one of the principal aggregates marketed and, because of special properties that make slag a selected aggregate for certain uses, the tonnage imbalance may be overcome by the importance of its contribution to quality or special characteristics of end products. The location and number (Fig. 1) of slag plants handling this annual production is governed by the geographic makeup of the iron producing industry. Prior to the period marked by World War 11, most blast furnaces were in the Great Lakes area-Pittsburgh, Cleveland, Chicago, Gary, Buffalo, Detroit, Youngstown, and Toledo, with exceptions at Baltimore, Bethlehem, and Birmingham. Since that time, iron and steel facilities have been established in Texas, Utah, and California. Today 85 slag plants in 15 states provide employment for almost 2000 persons. The slag plants also recover almost 4 million tons of slag-encrusted iron each year for return to the blast furnaces. Much of the success in developing uses for slag can be attributed to the efforts of the National Slag Association founded in 1918. Since then, it has conducted numerous field and laboratory investigations to demonstrate the properties and uses for slag and slag products. These investigations have resulted in total recognition of blast-furnace slag as a construction material of consequence. The American Society for Testing & Materials Designation C125 recognizes blast-furnace slag as "the nonmetallic product consisting essentially of silicates and aluminosilicates of

Jan 1, 1975

By C. T. Butler, W. W. Kay, R. D. Boddorff, R. L Ash

DRILLING and blasting in anthracite open-pit mines is a continuous problem to contractors and explosive engineers because of the diverse conditions caused by the nature of the geological formations, the extensive mining of the portions of coal beds near the surface, and the proximity of many strip pits to populated areas. Pennsylvania anthracite occurs in four separate long and narrow fields totaling only 480 sq miles. The coal measures are rock strata and coal beds that are considerably folded and faulted. The crests of the anticlines are eroded extensively. The beds outcrop on the mountain sides and dip under the valleys. At first only the upper portions of the syn-clines could be stripped. Now stripping to increasingly greater depths is economically possible, as is indicated by the fact that the proportion of freshly mined anthracite produced by strip mining has increased from 3.7 pct of the total tonnage in 1930 to 29.6 pct in 1950. Much of the rock overlying the deeper beds now being stripped is so extensively broken that considerable difficulty is experienced in drilling satisfactory blast holes and in using explosives in such manner as to insure a uniformly broken material easily removed by the excavating machinery. Such breaking of rock strata has occurred because the bed now being stripped has been mined extensively in former years by underground methods, and tops of gangways and chambers have subsequently failed. Draglines are used to uncover coal where the overburden can be moved with little or no re-handling. These machines range in size from those having a 2 cu yd capacity bucket on a 60-ft boom to those handling a 25 cu yd bucket on a 200-ft boom. Draglines are also used to strip to the bottom of the coal basins if the depth and the distance between the crops are not too great. For this type of operation blast holes are drilled full depth to the bed. These holes are commonly 30 to 90 ft deep; however, in exceptional cases, holes may be as shallow as 12 ft or as deep as 130 ft. Drilling is normally done for blasts of 12,000 to 60,000 cu yd of overburden, 30,000 cu yd being considered an average blast if vibration is not the controlling factor. Where the stripping of wide basins or the exposure of a moderately pitching vein makes the use of draglines impractical, dipper front shovels equipped with 4 to 6 cu yd buckets load into trucks. Overburden is removed in benches of 25 to 30 ft with blast holes drilled 4 or 5 ft deeper than the planned floor of the bench. For shovels under 5 cu yd bucket capacity the volume blasted varies from 8000 to 12,000 cu yd, whereas a volume of 30,000 to 50,000 cu yd of overburden is frequently blasted at one time for the larger shovels where vibration is not an important factor. During the past decade the churn drill, generally the Model 42-T Bucyrus-Erie blast hole drill equipped for drilling 9-in. diam holes, has become the most common blast hole drilling machine. Electricity powers half the churn drills in use and is preferred on the large strippings where electric shovels are operated and the working area is concentrated. On these operations the cost of additional electricity for the drills is less than the cost of fuel to operate diesel units because of the existing large demand load of the excavating equipment. Moreover, electric motors start more easily in cold weather and generally are less expensive to maintain. Diesel driven units are employed where a higher degree of mobility is required. The average drilling speed is 8 ft per hr, although in softer rocks a rate of 15 ft per hr is attained. Where rock is hard and strata is badly broken, drill speeds may be less than 2 ft per hr. Low drilling production results under these circumstances when loose material falling from the upper portion of the drill holes causes drill stems to be jammed. Rock formations vary so greatly in the region that a 9-in. diam churn drill bit may become dull after drilling only 2 ft or may drill satisfactorily for 56 ft; however, an average of 35 ft is usual in sandstone of medium hardness. Dull bits are hoisted to flat bed trucks by the sand line of the drill and are usually sharpened in the contractor's bit shop adjacent to the job. Care is generally taken to cover the thread end of the bit with a cap. To facilitate handling of bits around the drill, a heavy thread protector having an eye top is becoming more popular than the flat-top rubber or metal cap furnished with new bits. The 9-in. diam blast holes for a 25 to 30 ft bench are normally on 18x18 ft to 20x20 ft spacings, depending on the character of the overburden, although in broken ground 15x18 ft centers may be used to obtain better breakage and a more even bottom for the bench. The patterns of holes for shots

Jan 1, 1953

By John H. Hollomon, C. Zener

It is commonly recognized that a given material may be described as ductile or brittle only with reference to the conditions of test. Thus under the usual test conditions quartz is brittle, but under high pressures it is ductile. Salts that are brittle at room temperature become ductile at elevated temperatures. Pitch, brittle with respect to rapid loads, flows at low rates of loading. Pearlitic steel, ductile under the usual conditions of test, may be embrittled under the proper conditions of combined stresses, temperature, and rate of loading. Earlier Investigations A clear analysis of the conditions necessary for plastic flow and for fracture was first given by LudwikI1 who introduced two types of stress, the "flow stress" and the "stress at fracture." These stresses may refer to tensile or to shear stresses, or, in fact, to any type of stress. Ludwik considered these two stresses to be independent of one another, functions of the conditions of test and of the prior history of the material. For the purpose of analysis. both a Flow stress and a stress at fracture can be envisaged as functions of strain over the entire range from zero to infinite strain. Thus, the material is brittle if the stress at fracturc is less than the flow stress and ductile if the reverse is true. According to Ludwik's analysis, the problem of determining the effects of combined stresses, of temperature and of strain rate upon the behavior of metals reduces to a problem of determining the effect of these variables upon the flow stress and upon the stress at fracture. In the present paper, methods are described for determining the effects of two of these variables, temperature and strain rate, and examples are given of the dependence of tlow stress and stress at fracture, upon these two variables. The effect of combined stresses will be discussed in a succeeding paper. The flow stress may be determined from a load-diameter curve. Load-diameter curves were obtained over a wide range of temperature and over the limited range of strain rates obtainable with the lever-type Riehle machine used. The curves were then converted to an extremely wide range of strain rate by making use of the equivalence of the effects of changes in strain rate and changes in temperature, previously proposed2 and demonstrated3 by the authors. According to this principle of equivalence, strain rate e and temperature T affect the flow stress only through a single parameter-p of the form: p = eeQ/RT 111 In this equation, R is the gas constant (2 cal. per gram mol per deg. C.), and Q is a heat of activation, which varies from material to material, and may depend upon the strain, but not upon the strain rate or the temperature. There is associated with every value of p a flow-stress curve. article of strain rate and of temperature that give the same p have the same flow-stress curve. Therefore, merely by changing the temperature of test, the effect of changing the strain rate may be obtained. Thus, under isothermal conditions, the material will behave the same at

Jan 1, 1944

By J. W. Rutter, K. T. Aust

The migration of individual, large-angle grain boundaries has been studied as a function of tempereature and solute concentration in specimens of zone i.e filled lead containig very small additions of silver and of gold. Tile results are compared with various the-ories of grain boundary migration and with observations made prev.iorlsly of grain boundary migration in similar specimens of zone-refined lead containing tin additions. A previous investigation by the authors dealt with [he temperature dependence of grain boundary migration in bicrystals of zone-refined lead containing small additions of tin.' It was shown that tin additions as low as a few parts per million cause a large decrease in the grain boundary migration rate at any given temperature, as well as a marked increase in the temperature dependence of the migration rate. It was found that existing theories of grain boundary migration. based on the motion of dislocations. or upon the concept of atom transfer in groups across the boundary (group process theory). or upon the control of grain boundary motion by volume diffusion of impurity atonls along with the boundary. are incapable of accounting for the observations. The single process theory of grain boundary migration. which is an absolute reaction rate calculation based on the transfer ui atoms singly across the moving boundary, was found to predict the migration rate reasonably well for a number of boundaries whose motion was shown to be very little influenced by impurities, but not for boundaries whose illation was influenced markedly by impurities. It was concluded that the elementary process of grain boundary migration involves the activation of single atoms during transfer across the boundary. and that inadequate knowledge is available to permit the influence of impurities to be properly taken into account. The present study was initiated to check the validity of the above conclusions with other alloy systems, namely high-purity lead with small additions of silver and of gold. Both silver and gold diffuse faster. and with a lower activation energy of volume diffusion. than does tin in lead;' consequently, a study of the effects of silver and gold on grain boundary migration in high-purity lead offered a means of testing theories of boundary migration based on bulk diffusion of the solute (eg. ref. 3). In addition. it was hoped that the present work, in comparison with the results for tin in lead, would provide information concerning which factors are important in determin- ing the interaction between solute atoms and a grain boundary. EXPERIMENTAL PROCEDURE The preparation of bicrystals of zone-refined lead, with various silver or gold additions, was identical to that previously described for the lead-tin alloys.''4 Each bicrystal consisted of a striated crystal which was grown from the melt. and an adjacent striation-free crystal which was introduced by artificial nucleation and growth.''4 The striation or lineage substructure in the melt-grown crystal provided the driving force for grain boundary migration. During the preparation of striated single crystals by growth from the melt, it was found that silver or gold concentrations as low as 2 or 3 ppm by atoms were sufficient to cause formation of the hexagonal cell structure. which is due to the presence of impurity, during freezing. This structure is revealed on the solid-liquid interface by decanting the liquid during freezing. The hexagonal cell structure was observed previously4 in zone-refined lead crystals with tin contents above approximately 200 ppm by atoms. These concentrations of silver, gold, or tin are in agreement with the predicted amounts required for cell formation in lead,5'6 under the present conditions of freezing.4 The absence of cell structure at decanted interfaces, therefore, served as a useful indication that the silver or gold contents were less than 2 or 3 ppm by atoms in the specimens as grown. It was found that grain boundary migration occurred only very slowly when the solute content approached that necessary for cell formation. As a result, the present experiments were conducted with silver or gold additions less than 1 ppm by atoms. This impurity level is well within the solid solubility limits for silver and gold in lead.7 The annealing treatments, measurements of grain boundary velocities, and orientation determinations were carried out as described previously.' However. each bicrystal was also chemically polished in a solution consisting of 8 parts glacial acetic acid and 2

Jan 1, 1961

By D. L. Harris, A. M. Gaudin

Observations were made of the distribution of mercaptan containing S35 between aqueous solution and mineral and between aqueous solution and the gaseous phase. Although equilibrium may not have been attained, adsorption of the reagent was shown to occur reasily from air or aqueous solution on sphalerite, zincite, and willem-ite and to correspond to flotation. Adsorption on quartz did not similarly occur. THE following results, presented here in condensed form,' were obtained in a preliminary study of the adsorption of n-hexane thiol, hexyl mercaptan, on sphalerite, zincite, willemite, and quartz, from aqueous solution and from a gas. Interest in this subject was aroused by a Belgian report' of effective use of hexyl mercaptan for flotation collection of oxidized zinc minerals. The relatively low boiling point, 149°C, of the mercaptan3 suggested the desirability of extending the usual measurements of partition of collector between aqueous solution and gas and between gas and mineral. It is believed that this paper presents the first measurements of this type on a flotation system. Attempts were made to carry out the measurements at equilibrium, but as the work progressed it became increasingly doubtful that this desirable condition had been achieved. To control composition and extent of the gas phase, the apparatus was a wholly-enclosed thermally-controlled glass system. Because of these constraints and the desirability of dealing with pure minerals, a scale of operations was chosen in which a few grams of deslimed mineral were used in each test. It was also necessary to choose a particularly sensitive method for mercaptan analysis, and in fact a method that would permit the experimenters to follow the approach to equilibrium. For these reasons mercaptan marked by radiosulphur 35 was used. An analysis was made for the radiosulphur by a modification of the method of Gaudin and Carr. Coarsely-crystallized sphalerite was handpicked, stage-crushed in the dry state, wet-screened on a 200-mesh sieve, and deslimed in water at about 5 microns. Further treatment consisted of a wash in dilute aqueous hydrogen peroxide, drying, removal of the dark-colored fraction in a Frantz magnetic separator, washing in very dilute hydrochloric acid, repeated washing in distilled and conductivity water, and drying. The last washings showed a conductivity equivalent to a few ppm NaC1, that is, much more than would be provided, theoretically, by a saturated ZnS solution. The material was stored dry in sealed bottles. Analyses were as follows: Zn, 62.3 pct; Fe, 0.43 pct; Cd, 0.44 pct; S, 31.2 pct; Mn, 0.001 pct. The specific surface (BET method) was 2000 cm2/g. Zincite from Franklin furnace of the New Jersey Zinc Co. was hand-picked, dry-crushed, wet-screened at 100 mesh, and deslimed at about 10 microns. After drying, the associated zinc, manganese, calcium, and silicate minerals were removed in a Frantz magnetic separator. The purified zincite was washed in distilled water and conductivity water to a conductance of less than 2 ppm equivalent NaC1, dried, and stored. Analyses were as follows: Zn, 75.1 pct; Fe, 0.9 pct; Mn, 2.78 pct. The specific surface (BET method) was 1740 cm 2/g. Willemite, also from Franklin furnace, was purified similarly. Analyses were as follows: Zn, 52.5 pct; Fe, 0.12 pct; SiO², 27.3 pct; loss on ignition, 0.13 pct. The specific surface was 1760 cm 2/g. Conductivity water (double-distilled) and demin-eralized-distilled water were used in most of the tests. The specific resistance was not less than 600, 000 ohms, and usually above 1,000,000. Radiosulphur-marked hexyl mercaptan (1-hexane thiol) was synthesized by Tracerlab, Inc., Boston. Two lots were secured several months apart. The last lot, consisting of about 0.5 g of the mercaptan, had a total activity of about 10 millicuries. Tracerlab Co. guaranteed only the activity; hence a quasi -vapor pressure determination (based upon an S analysis) of the mercaptan was made. The calculated value, 4.2 mm of mercury at 25.5' C, has been compared with that of a sample of Highest Purity 1-hexane thiol from Fisher Scientific Co. The latter had a vapor pressure of 4.5 mm of mercury at 2.5 C. Analytical Procedures The sample containing radiosulphur-marked mercaptan was oxidized to convert the mercaptan sulphur to sulphate, carrier barium sulphate being added to provide a suitable quantity of total barium sulphate in a filter cake. The precipitate was filtered and dried, and counting was carried out either in a streaming-gas (Q-gas) counter for high sensitivity or with an end-window G-M counter for convenience. The oxidized and precipitated mercaptan gave a radioactive count of 65 counts per minute per microgram in the end-window Geiger-Mueller counter and 1100 counts per minute per microgram in a Q-gas counter. For standardization of the mercaptan solution, 15 replicate analyses were made. The average deviation per measurement was about 1600 cpm in 65,000 cpm, the probable error in the mean being 275 cpm. It

Jan 1, 1955

By D. E. Light, J. Y. Somnay

The use of alkyl acid phosphates and their alkali salts as collectors for the uranium minerals brannerite and uranothorite was investigated. In particular a detailed flotation study was carried out using isooctyl acid phosphate as a promoter. Tests were conducted on an Elliot Lake ore analyzing 0.11% U 3 O 8, chiefly as brannerite, and approximately 9% pyrite. Pyrite was floated with conventional reagents; the flotation of brannerite from the sulfide tails was studied to determine the optimum pH and pulp density to employ with isooctyl phosphate. 4 uranium recovery of over 90% was possible with a selectivity index of 8.95 when these tails were floated at 17% solids and a pH of 1.7. The effect of various modifying agents was also investigated. Aluminum sulfate, lactic acid and sodium silicate improved the selectivity of collection yielding selectivity indices of 9.5 to 11.5. Ferric chloride was found to be a depressant for brannerite. A Bancroft ore which analyzed 0.13% U308, and contained uranothorite was also amenable to flotation using isooctyl acid phosphate. The composite uranium concentrate obtained assayed 0.41% U308 at a recovery of 95.3% and a ratio of concentration of 3.24. Previous investigations1,2 on the flotation of brannerite, pitchblende, uraninite and/or uranothorite from various Canadian ores showed that fatty acids, including oleic acid and tall oils, petroleum sulfo-nates and alkyl acid phosphates, were suitable collectors for these uranium minerals. Additional work carried out by the Mines Branch in Ottawa on brannerite ores from the Elliot Lake area3 used the tall oil Acintol FA-1, or FA-2, as a collector. A recovery of 92% of the uranium in a concentrate which contained about 55% of the weight and assayed 0.2% U3O8 was obtained from a feed of 0.1% U308 in this latter instance. Eigeles et a1.4 carried out flotation on pitchblende ores and found that the most promising results were obtained with alkyl acid phosphates and their alkali salts as collectors. Within the homologous series of alkyl phosphates, the best flotation characteristics were displayed by isooctyl phosphates. Further, isooctyl phosphate derivatives were much less sensitive to hardness forming salts than oleic acid, enabling all flotation tests to be made with tap water. This paper describes tests employing alkyl acid phosphates for the flotation of ores containing brannerite and uranothorite. The flotation work described herein was conducted in conjunction with the development of a leaching process for Elliot Lake, Ontario, brannerite ores. In this process pyrite in the ore was concentrated by flotation and roasted, providing sulfur dioxide which was used to produce sulfuric acid in situ in a liquid-solid extraction process. A 40% conversion to sulfuric acid was indicated at a leaching temperature of 80°C; this resulted in the extraction of 93% of the total uranium after a contact period of 6 hr. A rotary kiln was used as a leaching vessel. Preconcentration by flotation was studied in conjunction with the above process to reduce the bulk of solids for leaching and, consequently, capital expenditure. The materials and methods used in this study will be described initially. Then the results will be presented in two sections, the first dealing with the brannerite ore, and the second with the uranothorite. Finally an economic analysis of the results on the brannerite material will be made. MATERIALS AND METHODS The two ore samples examined were from uranium-producing mines. One was a brannerite ore, a uraniferous quartz pebble conglomerate from the Elliot Lake area, which contained 0.11% U3O8, 4.3% S and 4.5% total Fe. Mineralogical studies of similar samples indicated the presence of quartz, microcline, sericite, pyrite and minor quantities of rutile, pyrrho-tite and zircon. The other ore was from a biotite-rich pegmatite in the Bancroft area; feldspar, quartz and biotite formed the major gangue components. Uranothorite was the principal uranium mineral; the head assay was 0.13% U 3 O 8. Preparation of Feed: The ores were crushed to —10

Jan 1, 1963

By J. E. Campbell, G. D. Calkins, N. M. Ewbank, M. Pobereskin, A. Wesner

GRINDING for size reduction affects the economics of many processes and products. It is essential as the first step in many industrial processes and is also a finishing step for materials with properties depending on particle size, such as talc, cement, and silica sand. Intermediate and fine grinding are vital operations in the U. S. cement industry, which is producing more than 250 million bbl of cement per year.' Wear of the grinding media is a large part of the grinding operation cost. Problems encountered in grinding cement are so complex that evaluation of efficiency and economy of grinding media is difficult.2 It has been especially difficult to evaluate the relative effectiveness of different types of balls because there are no good testing techniques. Many other industrial operations can be evaluated on a laboratory scale with reasonable accuracy. This does not hold true for evaluation of grinding balls. The consistent results obtained in a laboratory test under a given set of conditions are not always borne out in field application. Rough evaluations of the effectiveness of various compositions and types of grinding balls have been made in the field by using a full charge of one type in a mill and comparing the production record with another run using another type of ball. This method is time-consuming and not very precise, as the second run may not have been carried out under identical conditions. Laboratory-scale tests, on the other hand, have yielded inconclusive results, and many investigators have turned their attention to the development of a field testing technique. Field testing small sample lots of grinding balls has been impractical because it is difficult to identify and recover the test specimens from the grinding mill, and individual groups of balls that have undergone different heat treatments can not be separated.".4 To overcome these difficulties, previous investigators have identified the balls by distinctive marks, notches, and drilled holes, but this procedure has three serious drawbacks: 1) Grinding characteristics and quality of the steel balls may be affected. 2) Physical markings may be worn away in the grinding process, especially during a prolonged run. 3) Recovery from the bulk of the charge will be extremely difficult because the markings are hard to see and may be masked by a coating of the product. To circumvent these difficulties, a radioactive-tracer technique was proposed for recovery and separation of steel grinding balls and subsequent evaluation of the various compositions of the balls. The proposed technique involved five basic operations: 1) Thermal-neutron irradiation activation5 of each group of test grinding balls to a different level of specific radioactivity. 2) Addition of groups of radioactive steel-ball specimens into a ball tube mill. 3) Recovery of radioactive steel-ball specimens from the bulk of the mill charge. 4) Separation of the various groups by their specific radioactivity. 5) Evaluation of actual grinding ball wear. Before any physical tests were performed, required neutron irradiation intensity and time were calculated. Probable composition of the steels to be used was ascertained. An examination was made of the radioactive nuclides8 to be formed which would contribute measurably to the radiation level immediately after irradiation and during the test operation. The radioisotopes formed, their types of radiation, and their half lives are listed in Table I. Of these radioisotopes only iron-59 and chromium-51 were significant for the actual wear test. The intensity of radiation that could be detected by a Geiger counter when the test was completed was the basis for the minimum activation level established. The intensity of radiaton that could be safely handled at the beginning of the test was the basis for the maximum activation level, although this was not considered a major problem. Ten groups of grinding balls of various composition and/or surface or heat treatment were to be tested. One group was designated for the minimum irradiation time. The remaining groups were designated for irradiation periods that increased by increments of 33 pct from that of each preceding group. This difference was considered enough for separation and identification of the groups by comparison of specific activity. Potential Hazards: Possible radiation hazards that might be encountered during this experiment were evaluated for the three important phases: 1) the radiation hazard of placing balls and removing them from the mill, 2) contamination of the product cement by radioactive material worn from the balls, and 3) contamination of the steel by the radioactive balls left in the mill. The radiation intensity expected from the whole group of radioactive balls was calculated to be 250 milliroentgen per hr at 1 ft. This meant the balls would require special shielded packaging and warning labels on the shipping containers. In a radiation field of 250 mr per hr a man can work for 1 hr without exceeding maximum permissible weekly exposure. Since the balls could be dumped into the mill in a matter of seconds, relatively little radiation exposure was anticipated at this stage of the operation. If the weight loss in the balls was 7.7 pct per month and the cement feed through the mill was

Jan 1, 1958

By J. B. Stubbins, R. A. Blais

Extensive geological work was initiated — and continues — when operations of the Iron Ore Co. of Canada commenced in the Labrador-New Quebec area. Such geological operations include: mapping, test pitting, drilling, underground workings, volume factor and structure tests, and the calculation of ore grades and tonnages. Details of such work are given. Development is carried sufficiently ahead of mining to provide reliable tonnage and grade estimates and allow final mine planning. In order to make full use of geology in mining operations, the pit engineer combines the duties of geologist and mining engineer. The iron deposits of the Knob Lake range are located in the central part of the Labrador peninsula, a territory nearly twice the size of Texas, which is bounded by Hudson Bay on the west, Hudson Strait on the north, the Atlantic Ocean on the east and the Gulf of St. Lawrence on the south. The mining district proper is about 1000 miles northeast of Toronto. A 360-mile railroad links this mining area to the port of Sept-Iles on the Gulf of St. Lawrence. Schef-ferville, which is only a few miles from the open-pit mines, is the center of operations of the Iron Ore Co. of Canada. It has a population of nearly 5000. The nearest settlement is Labrador City, some 120 miles to the south, where this company is erecting a large plant for beneficiating its huge reserves of local low-grade iron ores. HISTORY The mineral possibilities of the area were recognized as early as the end of the last century, when A.P. LOW' of the Geological Survey of Canada made his famous trek across the Labrador Peninsula. After mapping several belts of iron formation, Lovr recommended that the area be thoroughly prospected for iron. In 1929, two well known Canadian geologists, J.E. Gill and U'.F. James, led a private expedition in central Labrador and discovered the first deposit of high-grade iron ore near what is now the Ruth Lake Mine. In 1936 the Labrador Mining and Exploration Co. was formed to 11ake over a prospecting concession of over 20,000 sq miles in central Labrador. An adjoining concession of 3900 sq miles in New Quebec was obtained in 1942 by Hollinger Consolidated Gold Mines, which had just Purchased the Labrador Co. The same year the M.A. Hanna Co. Purchased an interest in both exploration companies. From 1942 to 1950 extensive exploration was conducted by the Hollinger-Hanna technical staff to systematically appraise these vast concessions. More than 40 deposits of high grade ore were found and, by the end of 1950, the total ore reserves reached 418 million tons. In 1949 five American steel companies joined the Hollinger-Hanna interests and formed the Iron Ore Co. of Canada. Financing and full-scale construction were decided upon in 1950. This included the construction of a 360-mile railroad through very difficult terrain, the erection of two hydroelectric plants, the installation of terminal port facilities at Sept-IIes, the building of a modern town-site at Schefferville, the construction of crushing and screening plants, and the preparation of deposits for mining. Ore was first shipped in July 1954. Total open-pit mine production to date is 66 million long tons of direct-shipping ore. GEOLOGICAL ENGINEERING The above achievements would not have been possible without irtegrated teamwork of people of diverse skills and extensive use of geology. In their paper on the role of geologists in the development of this iron ore field, (Gustafson and Moss1 rightly emphasized the difficulties facing the early workers in the area. In an uninhabited land with no roads or railroads and no navigable rivers leading to the interior, everything had to be flown in. It was not until 1948 that aerial photographs and adequate base maps became available. In spite of these and other difficulties, an impressive amount of field work has been done since 1942. Nearly all this work has been directed by geological engineers and geologists. About 15,000 :sq miles have been geologically

Jan 1, 1962

By S. D. Baumer, P. M. Hulme

IN the late thirties, the National Carbide Co. cooperated with C. E. Wood, of the U. S. Bureau of Mines, in his investigation of the relative merits of various desulphurizers, including soda ash, caustic soda, and calcium carbide. Laboratory tests showed that carbide, when it could be made to react, is an excellent desulphurizing agent for molten iron. Sulphur content can be driven to lower levels and higher extractions obtained with carbide than with actionsany of the more common reagents. Wood's results1 are shown in Table I. Unfortunately, as the Handbook of Cupola Operation puts it, the chemical fact that carbide is a good desulphurizer was of only academic interest because it was found to be extremely difficult to devise a practical means to make it react with molten iron. Calcium carbide is formed in the electric furnace at 4000°F and above, and its softening point is probably at least 500 °F above the usual working temperatures encountered in iron and steel practice. Consequently, carbide does not form a true slag but floats as a dry powder on top of the metal and only a very small portion of it ever comes in actual contact with the iron. Stirring with a rabble, or pouring the metal over the carbide, increases the efficiency only slightly. Extractions of 20 to 30 pct can be obtained in this manner, but conventional soda slag treatment can do better than this and do it more cheaply. All attempts to lower the melting point of carbide in order to obtain a reactive, liquid slag have so far proved fruitless. Directly under the arc in a metallurgical electric furnace, carbide becomes highly reactive. Excellent sulphur removal can be obtained without any slag other than a thin layer of carbide." imilarly, good results are obtained by adding small amounts of carbide to the finishing slag in double-slag arc furnace practice. To react a liquid with a solid, it is axiomatic that the liquid has to wet the solid before anything can happen. If the solid is heavier than the liquid, the problem is easy, but it becomes more difficult when the solid is much lighter than the liquid, as in the case of carbide and liquid iron. Wood recognized this problem and solved it in a unique fashion. The results shown in Table I were obtained by spinning the carbide beneath the surface of the molten iron by means of a refractory centrifuge. This technique allowed each particle of the finely divided carbide to come into intimate contact with the metal and to be wetted thereby. Wood's centrifuge technique was successful in the laboratory where it achieved excellent and consistent results. Some attempts were made to expand this method to commercial practice, but serious difficulty was encountered in obtaining a refractory centrifuge head that would be economically feasible. About this time the war intervened and the project lay dormant for several years. In 1944, it was revived. It was suggested that the carbide could be blown into the metal with a carrier gas in an attempt to eliminate the necessity for the expensive and brittle centrifuge. The idea was first tried out in a fairly large ladle of iron using natural gas as the carrier. Considerable sulphur was removed, but it was quite obvious that the use of natural gas was not practical. Attempts then were made to blow carbide into molten iron using, in turn, nitrogen, argon, carbon dioxide, air, and oxygen. The latter two gases proved unsatisfactory. Calcium evidently prefers oxygen to sulphur because in the tests calcium oxide and carbon dioxide were produced, the sulphur still being untouched in the iron. Nitrogen, argon, and carbon dioxide gave much better results, although the efficiencies and extractions were erratic, and only a few isolated tests approached the results obtained by Wood. Table II shows typical results obtained with these gases. The sulphur removals were interesting, sometimes even encouraging, but it is evident that such erratic behavior could not be tolerated in commercial practice. A number of different types of equipment, such as sand blasting machines, refractory guns, and the like can used to blow the solid into the metal. All types required relatively large quantities of gas in order to maintain the flow of solid carbide through the system and into the metal. It was observed that the bubbles of gas breaking through the surface of the metal contained quantities of unreacted carbide. The liquid metal never came in contact with these particles and if it cannot wet them it cannot react with them. The initial work had shown that carbide had great possibilities as a desulphurizer. In practice

Jan 1, 1952

By K. G. Davis, P. Fryzuk

The diffusivity of silver in liquid tin has been determined, using the capillavy-reservoir technique, over the temperature range 250° to 500°C. The new value, D = 2.5 x 10'* exp(-2480/ RT) sq cm per sec, differs from that obtained by other workers in an earlier investigation. The analysis of data from the capillary-reservoir technique is discussed. In a recent investigation of the solidification of dilute alloys, values for the diffusion constant of silver in liquid tin were required in the analysis of the formation of impurity substructures. AS a result, measurements were made of the diffusion constants in the temperature range 250° to 500°C (melting point of tin 232°C), for the alloy concentrations used in the solidification experiments and at higher concentrations, to verify previous determinations.I)2 The capillary-reservoir method was adopted, using experimental procedures similar to those followed by Ma and Swalin,1 with the main exception that radioactive silver was used in the present investigation to facilitate solute-concentration measurements. EXPERIMENTAL PROCEDURE a) 100 ppm Samples. Glass capillary tubes of 2 mm inside diameter and approximately 5 cm- long were sealed at one end, evacuated, and filled with tin of 99.999 pct purity. The region of shrinkage near the mouth was cut off, and the tubes were then placed in a graphite holder and immersed, with the open end up, in an unstirred bath of alloy containing 100 ppm Ag 110, where they remained for periods of up to 30 hr. On removal from the bath they were cooled by an air blower. The bath was kept under a small positive pressure of argon, and the temperature controlled to within +1°C. A 10-hr diffusion period was used in the majority of the tests, scatter on runs of less than 5 hr being rather large. The procedure outlined above was chosen in preference to putting alloy in the capillary and pure tin in the bath, in order to avoid segregation when the tubes filled with alloy were first solidified. To minimize segregation when the diffusion period was complete and the capillaries again solidified, the earlier samples were held in thin-walled silica tubes which could be cooled very rapidly. Later tests were made in precision-bore Pyrex tubes, to eliminate effects caused by variations in the capillary diameter. No consistent differences in diffusivity as measured in the two types of tube were detected. After removal from the glass tubing, the samples were sectioned into 2.5 mm lengths and counted for y activity, using a scintillation counter with fixed geometry. Samples were also drawn directly from the bath and counted, so that values for C/C,, the ratio of the weight of Ag 110 in the sample to that in the bath, could be obtained. b) 5000 ppm Alloy. To check for possible effects of concentration, the silver content of the bath was increased to 5000 ppm. Complete mixing was found to have taken place in the capillary after a 10-hr period at 300°C. It appears that the greater density of the alloy was sufficient for buoyancy forces to cause instability in the alloy-tin interface, leading to rapid convective mixing. For the 5000 ppm alloy, therefore, the bath was of pure tin and the capillary tube was filled with alloy. With this arrangement, values of D consistent with those for the 100 ppm alloy were obtained, Fig. 1. CALCULATIONS OF DIFFUSIVITY The terminology used applies to a capillary of pure tin immersed in a bath of alloy. 1) Error-Function Method. under the present experimental conditions, the rod of liquid tin into which silver is penetrating may be considered semi-infinite. Assuming the concentration at the mouth of the tube to remain constant at Co, the concentration C at distance x from the mouth of the tube at time / is given by3 Plots of the inverse error function of (1 -C/Co) vs .v gave straight lines passing through the origin with slope 1/2-, x being corrected for shrinkage both on solidification and while cooling to the melting point (total correction about 6 pct at 500°C). Values for log D obtained in this manner are shown in Fig. 1. A least-squares fit to the relation D = Do exp(-Q/RT)

Jan 1, 1965

By J. S. Marsh

OPPORTUNITY to pay tribute to the memory of Professor Henry Marion Howe is a strenuous assignment as well as an honor. Upon recalling Howe lecturers and lectures of the past 25 years, glancing over the list of those earlier, and rereading Howe's books, I arrive at several conclusions: 1—Many lecturers either worked under or knew Professor Howe. 2—It is virtually impossible to pick a subject on which Professor Howe did not touch. 3—There is precedent for a technical paper based upon pursuit of a single subject. 4—There have been listening lectures and reading lectures. There is solid comfort only in 2: the subject field is wide open. I did not know, nor even ever saw, Professor Howe, so can supply no fitting reminiscence. As a college student I was dimly aware that he counted among the giants. Fuller appreciation of his stature came with reading his books and papers, growing acquaintance with some of his associates, and the intrinsic dignity of the climax of the Annual Meeting, beginning at four o'clock of a Thursday afternoon in the auditorium of the Engineering Societies Building in New York. As for producing the technical paper sort of thing, it is my lot to have reached an age and assignment such that to do so would be to filch information from those who did the work and whose story is theirs to tell; for this I have no enthusiasm. As for the final conclusion, Professor Howe was one of the chosen few so highly expert at expository writing that he could produce a lecture or paper that reads as though it would also have listened well. One of his tricks was the free use of words not ordinarily part of the technical vocabulary, provided that such words were likely to communicate most precisely what he had in mind. How wonderful it would be for all who must read reports by the ton if ability at exposition could be taught with the effectiveness open, say to, differential calculus! Perhaps Professor Howe should be required college reading even if for no other reason than to prove that technical writing need be neither dull nor diffuse. My assignment is clearly still strenuous. Another point to consider is the fact that metallurgy is now so tremendously diversified that hope of finding a topic of universal appeal is negligible, even if one were competent enough to be permitted free choice. That which follows is, therefore, a compromise composed of necessity and of the obligation to attempt to avoid boring to slumber those of you who are not especially interested in the general subject chosen. The Iron and Steel Div. is now essentially a process metallurgy division, heavily concerned with the smelting of iron and the making of steel. The American Iron and Steel Inst. figure for present steel capacity of this country is 125,828,310 net tons; how this is divided among processes is indicated by the production totals for 1953, shown in Table I. The glamor girls and boys make the front page and so it is with steelmaking processes. If there is an Antarctic Daily Bugle, it undoubtedly has carried stories of revolutionary development, such as oxygen processes and vacuum melting, and stories of the incomparably rosy destiny of electric arc melting. All such certainly have their place and their future; meanwhile, it is the sturdy and old reliable open hearth that accounts for the bulk of production reported back on the financial page, and it is the old reliable that is most likely to continue to account for the bulk for some perfectly sound raw material, technologic, and economic reasons. This, plus the fact that next year marks a centennial (for it was in 1856 that Frederick and William Siemens conceived the regenerative open hearth), is reason enough to talk about open hearth furnaces, but is not the real one. The real reason is that in some years of association with open hearths, I have accumulated—in addition to a genuine liking and respect for them—certain odds and ends of fact and fancy that this lecture provides a unique chance

Jan 1, 1956

By J. W. Spretnak, G. W. Powell, J. H. Bucher

Tlze room-temperature tensile fracture oj smooth, round specitnens of three ultrnhigh- strength steels tempered to a wide range of strength levels was studied by means by light and electron-microscopic examination of the fracture surfaces. The fracture of AISI 4340 and 300 M at all the strength levels studied, and H-11, except after tempering at 1200° and 1300°F, occurs in three stages. The initiation of fracture is internal (except in some lightly tcmpeved specimers in which fracture is initiated at surface flaws), and is nucleated largely by separation at metal-second phase intevjaces. TIze voids grow and, coalesce to form a crack. When the crack has reached a sufficienl size, rapid propngutio~z ensues. Failure in this stage of fracture usually occurs by dimpled rupture of inicroshear stefis. In the case of H-11 tempered in the 1125° to 1300°F range, fracture in the shear steps is predominantly by concentrated deformation without void formation. The termination of fracture is usually occomplished by the formation of a shear lib in which fracture occurs by shear dimpled rupture. In the case of H-11 tempered at 1200° and 1300°F, no shear lip was obserued, and the radial elelments extend to the surface—a true termination slage does not exist. ThE tensile fracture of several metals and alloys has been investigated.2-4 In the case of polycrystal-line materials, cup-cone fracture usually results. The mechanism of cup-cone fracture may be summarized as follows.5 Cavities are formed in the necked region of the specimen. They usually are initiated by inclusions or second-phase particles. The cavities extend outwards by means of internal necking, and a crack lying about perpendicular to the length of the specimen is formed in the necked region. Subsequent crack growth occurs by the spread of bands of concentrated plastic deformation inclined at an angle of 30 to 40 deg to the tensile axis. Cavities are formed in the bands of concentrated deformation. The deformation bands zigzag across the bar with the net result that mac-roscopically the crack extends about perpendicular to the specimen axis. The final separation, or cone formation, appears to occur by continued crack propagation along one of the deformation bands out to the surface of the specimen. The micromechanics of the tensile fracture of ultrahigh-strength steels have not been thoroughly investigated. Larson and carr6,7 studied the tensile-fracture surfaces of AISI 4340 with a low-power microscope and reported that three stages of fracture could be observed in general. A centrally located region characterized by circumferential ridges, an annular region characterized by radial surface striations, and a peripheral shear lip were found. It was first pointed out by 1rwin8 that the central region is very probably one of fracture initiation and slow growth, and that the annular, radially striated region is one of rapid crack growth. Presumably the crack grows slowly, assuming roughly a lenticular shape, until it is large enough for the initiation of rapid propagation. In this investigation, it was attempted to determine the fine-scale aspects of the room-temperature tensile fracture of some ultrahigh-strength steels, and to relate the variation in fracture mode with microstructure. The steels studied were AISI 4340, 300M, and H-11 tempered to a wide range of strength levels. I) EXPERIMENTAL PROCEDURE The compositions of the steels studied are given in Table I. The steel was received in the form of hot-rolled bar stock 5/8 to 1 in. in diameter from which oversized specimens were machined and heat-treated. The heat treatments employed are given in Table 11. Subsequent to heat treatment, the specimens were ground to the final dimensions and stress-relieved by heating for 1 hr at 350°F (with the exception of the as-quenched steel). Standard smooth round specimens of 0.252-in. diameter and 1-in. gage length were tested in a Tinius Olsen Universal Testing Machine using a cross-head speed of 0.025 in. per min. The relatively coarse aspects of the fracture topography were determined by light-microscopic examination of sections through the fracture surface of nickel-plated specimens. A direct carbon-replication technique9 was used in the electron-microscopic study of the fracture surfaces. The replicas were examined in the electron microscope, and stereo pairs of electron micrographs were taken. The stereo pairs were then examined using a Wild ST4 Mirror Stereoscope. Carbide and inclusion particles extracted in the replicas were analyzed by selected-area electron diffraction. II) EXPERIMENTAL RESULTS The mechanical testing data are summarized in Table 111. The values reported are the average of

Jan 1, 1965