Search Documents

By Neils Hansen

The microstructure of dispersion-strengthened aluminum aluminum-oxide products containing from 0.2 to 4.7 wt pct of aluminum oxide has been examined by optical and transmission electron microscopy, and the flow stress has been determined at room temperature and at 400C by tensile testing. Products were examined as recrystallized and as high-temperature extruded, and the microstructures consisted of a fine dispersion of oxide particles in a matrix divided by respectively recrystallized grain boundaries and subgrain boundaries. The flow stress (0.2 pct offset) at room temperature of recrystallized dispersion strengthened aluminum aluminum-oxide products is the superposition of dispersion strengthening and grain boundary strengthening. This superposition has been found to be linear. The flow stress (a) can be related to the grain size (t) by the Petch equation: ing content of oxide and k is a constant independent of the oxide content. For extruded products a similar relation has been found by replacing the grain size by the subgrain size. The k-value is of the same order for the two types of structure, which shows that the subgrain boundaries are as effective slip barriers as grain boundaries. Tensile testing at 400C of re-crystallized and extruded products shows that oxide dispersion strengthening is very effective, whereas the strengthening effect of grain boundaries and subgrain boundaries is small. THE microstructure of dispersion-strengthened products consists of hard particles finely distributed in a metal matrix. The strengthening effect of the dispersed phase has been fairly well established,1 and it has been found that the size and volume fractions of the dispersed particles are important structural parameters. However, in many dispersion-strengthened products which have been worked and heat-treated during manufacture the matrix is divided into well-defined grains or sub-grains, which may also have a strengthening effect. A model of the matrix strengthening in dispersed products worked during manufacture has been proposed,2 introducing the energy of the structure as a strengthening factor, especially at low temperatures. A difficulty in this model is, however, to relate this (stored) energy to the structural parameters directly observable as for instance grain size. The strengthening effect of the matrix grain size after recrystallization has been in- vestigated for nickel-thoria (TD-Nickel) products3 and for copper aluminum-oxide products. Conclusive results were, however, not obtained as the grain size of TD-nickel was constant. 5 to II , after recrystallization at temperatures from 700 to 1200°C and as the copper products containing 5 to 1 wt pct of aluminum oxide could not be recrystallized even after severe cold reduction and heat treatment at 1050C. For aluminum aluminum-oxide products containing from 1 to 5 wt pct of aluminum oxide it has been shown that the tensile strength at room temperature decreases when an extruded product is cold-worked and recrystallized. The matrix in the extruded products is divided into well-defined subgrains of micron size, and as the grain size of the recrystallized products is about two orders of magnitude higher, it is obvious that grain boundary strengthening occurs. Preliminary results8 have indicated that the flow stress containing no grain boundaries, A is a constant and t is the subgrain size. At elevated temperatures the effect of boundaries is more complex; it has been shown11 that recrystallized products having an oxide content of about 3 wt pct are more creep resistant than extruded material in the temperature range 400° to 600°C, whereas on application of a higher strain rate the tensile flow stress (0.2 pct offset) is higher in extruded than in recrystallized aluminum—5 wt pct aluminum oxide products at temperatures from room temperature to 427°C (800), Finally it has been shown12 that the Brinell hardness at 350°C of extruded products having about the same content of aluminum oxide increases with decreasing grain size, determined by X-ray line-width measurements. The present study was undertaken to obtain a quantitative relationship between the tensile strength and the grain size of aluminum aluminum-oxide products in the recrystallized as well as in the extruded state. The tensile testing was performed at room temperature and at 400uC. The grain size of the recrystallized products was varied by changing the degree of cold-work preceding the recrystallization heat treatment. In extruded products grain (or subgrain) size variations were obtained by high-temperature heat treatment after extrusion. EXPERIMENTAL a) Materials. Aluminum aluminum-oxide products have been manufactured by consolidation of aluminum powder covered with a layer of aluminum oxide formed during powder manufacturing. The products examined were manufactured from atomized powder containing

Jan 1, 1970

By P. Beardmore, B. W. Howlett, B. D. Lichter, M. B. Bever

The heats of formation at 273°K of the compounds Mg2Ge, Mg2sn, and Mg2b, the heats of fusion and melting points of Mg2Sn and Mg2Pb, and the heats of solution of magnesium, germanium, and lead in liquid tin have been measured. The excess free energies of the liquid alloys and the free energies of formation of magnesium-Group IVB compounds at their melting points and their standard free energies of formation at 298°K have been calculated. The stability and bonding of the compounds are discussed with reference to these properties. Some thermodynatnic aspects of the liquid phases in the systems Mg-Sn and Mg-Pb are also considered. THE compounds of magnesium with the Group TVB elements, silicon, germanium, tin, and lead, have often been considered to constitute a nearly ideal homologous series. In particular, their thermodynamic stability has been assumed to decrease with increasing atomic number of the Group IVB element.' The binary-phase diagrams of the magnesium-Group IVB elements given by Hansen and Anderko2 have the same form. Each system has a single con-gruently melting compound of limited homogeneity range. The structures of these compounds, which have the formula Mg2X, are anti-isomorphous with the calcium fluoride structure. A recent investigation has found evidence of a second compound in the system Mg-Pb.3 The solid compounds Mg2Si, Mg2Ge, and Mg,Sn are semiconductors, while the conductivity of Mg2Pb approaches that of a metallic conductor. This difference suggests that other properties may also show a discontinuity. The investigation reported here is concerned with the thermodynamic properties of magnesium-IVB compounds and particularly their variations with the period of the Group IVB element. The heats of formation at 273°K of the compounds MgzGe, Mg2Sn, and Mg2Pb and the heats of fusion and melting points of Mg2Sn and Mg2Pb have been measured. The results, combined with published data, are interpreted in relation to the stability and the bonding characteristics of the compounds. Some thermodynamic aspects of the liquid phases in the systems Mg-Sn and Mg-Pb are also considered. In the course of the investigation the heats of solution of magnesium, germanium, and lead in liquid tin have been determined. 1) EXPERIMENTAL PROCEDURES 1.1) Samples. Samples of the compounds Mg2Ge, Mg2Sn, and Mg2Pb, supplied by Professor P. Aigrain, Compagnie Générale de Télégraphie Sans Fils, were used in measuring heats of formation, heats of fusion, and melting points. Samples of Mg2Sn and Mg2Pb, supplied by Dr. V. B. Kurfman, Dow Metal Products Co., samples of Mg2Sn, prepared at the Air Force Cambridge Research Laboratories, and samples of MgzPb, prepared in this laboratory, were used for additional measurements of the heats of fusion and the melting points. The samples were stored in evacuated Pyrex capsules or under nonreacting liquids. 1.2) Heats of Formation. The heats of formation at 273°Kof the compounds Mg2Ge, Mg2Sn, and Mg,Pb were measured by tin-solution calorimetry. In this method, samples of the compound and of a mixture of the constituent elements are added alternately from 0°C to a tin-rich bath. The difference between the heat effects, corrected for the change in composition of the bath, is the heat of formation of the compound. Details of the method have been given elsewhere. 4 The bath was maintained at 350°C for the dissolution of the compounds MgzSn and Mg2Pb. Since at this temperature the dissolution of Mg2Ge was too slow, a bath temperature of 400" or 450°C was used with this compound. At least three calorimetric runs, each of approximately six additions, were made with each compound. 1.3) Heats of Solution. The determination of the heats of solution of magnesium, germanium, and lead in tin was included in this investigation because they were not well-established at the time this work was started. To obtain the heat of solution, the difference

Jan 1, 1967

By H. H. Rachford

Numerical solutions of immiscible flow problems in which dispersive effects of capillarity are dominated by convection require excessively fine grid spacing with attendant high computing costs. The use of coarser spacing reduces cost but often produces oscillation or undue dispersion associated with displacement fronts, A numerical formulation is proposed here which should be applicable to two-dimensional flow problems. it is in part analogous to an approach previously tested for miscible systems. The convective transport is approximated using a change of variables to yield a coordinate system moving approximately with the local characteristic velocity. The capillarity-induced dispersive terms in the differential system describing the process are approximated with respect to a fixed coordinate system by the usual implicit formulation. One-dimensional tests of the procedure yielded results in which the saturation profiles tended smoothly to the zero-capillary pressure solution as the ratio of viscous to capillary forces was successively increased in a sequence of calculations. This contrasted favorably with solutions by other numerical procedures which would require attendant grid refinements to approach the zero capillary pressure results. INTRODUCTION Numerical solution of displacement problems has until recently relied on applying methods developed primarily for transient heat-flow problems. Such problems are classified as parabolic in type, and where the heat transport is purely by diffusion their solutions are characterized by a high degree of smoothness. It is not surprising, therefore, that for approximating these solutions available finite difference methods are quite adequate. In flow problems the transport is partly by diffusion, partly by convection or flow. Although the problem remains of parabolic type because the dispersive effects of capillary forces or diffusion play some role in every displacement, at high flow rates the problem is dominated by convection, and solutions tend toward those of equations of the hyperbolic type. Solutions of hyperbolic problems are characterized by the translation of fronts, or discontinuities, that may progressively increase in sharpness. Numerical methods for treating parabolic problems become less and less satisfactory as displacement rates increase and the role of dispersion due to concentration or capillary pressure gradients becomes small relative to transport due to flow. In computation the difficulty manifests itself as an error associated with the grid size chosen. 1-6 In summary, if the heat-flow type approximations are to include the terms arising due to convection, one of several choices may be made: (1) an upstream (to the direction of flow) approximation for the convection terms may be used; (2) a centered-in-distance (CID) approximation may be used; or (3) a recently developed approximation based on the theory of oscillation matrices may be chosen.6 The last appears to have significant promise for one-dimensional flow problems; its extendibility to two or three dimensions is an open question. In either of the first two approaches, a suitably small ratio of v&/D must be maintained, where v is the velocity, & is the grid spacing and D the effective dispersivity in the direction of flow. In the first choice, the approximation of the convective part is only first-order correct and errors introduced appear as a numerically induced dispersivity of magnitude proportional to v?x. In the CID choice, the approximation can be second-order correct, but the difference formulation fails to satisfy the maximum principle unless a condition on v?x/D is met. Practically, this means that for high flow rates oscillatory solutions may result in the neighborhood of a front unless exceedingly small grid intervals are taken. While the procedure proposed by Stone and Brian4 permits a less severe limitation to be placed on this ratio, ultimately the flow rates increase relative to the dispersivity the oscillation obtains. Further, extensions of their approach to higher dimensional systems may be attended by considerable

Jan 1, 1967

By A. S. Yue, A. E. Vidoz, F. W. Crossman

Tensile specimens were prepared from a single grain of an epitaxially grown Al-CuAl2 eutectic ingot. The eutectic lanzellae were oriented parallel and perpendicular to the tensile axis of the specimens. Since the composite was of the eutectic composition, the aluminum-rich matrix could dissolve up lo 5. 7 wt pct Cu in solid solution and, therefore, was amenable to strengthening by precipitation hardening. The tensile properties of the eutectic single crystals were determined at room temperature as functions of interlamel-lar spacing, platelet orientation, and thermornechanical trealment. The obserced variations in composite stress and modulus with respect to the level of&apos; composite strain are discussed in terms of premature fracture of CuAlz platelets, a distribution function for the strength of the lamellae, and unequal strains due to localized fracture of&apos; platelets. The discontinuous fiber composite model of Kelly and Tyson is modgied to account for a changing distribution of fiber lengths during composite loading. The tensile properties at elevated temperatures were determined for the direc-tionally solidified eutectic oriented with platelets parallel to the tensile axis. The observed properties are attributed to the onset of plasticity of the CuAL2 phase above 150°C. DURING the investigation of whisker- and fiber-reinforced metallic matrix composites in recent years, two major problem areas have developed: 1) The fabrication of the composite involves tedious handling techniques in order to obtain a unidirection-ally aligned and uniformly spaced set of whiskers in the metal matrix. 2) Due to weak interfacial bond strengths or because of the formation of additional embrittling phases at the metal-fiber interface during long-time exposure or fabrication at elevated temperatures, many composite systems have exhibited considerably lower strengths than those predicted by a law of mixtures analysis.&apos; These problems have been bypassed by the technique of growing whiskers and plates of high-strength materials in a ductile metal matrix by controlled unidirectional eutectic solidification.2 The tensile properties of directionally solidified A1-CuA12 eutectic are presented here. This alloy consists of a ductile aluminum matrix, containing up to 5.7 wt pct Cu in solid solution, which is amenable to precipitation hardening by heat treatment and a reinforcing high modulus CuAlz intermetallic phase. The two phases are present in the form of alternating platelets or lamellae. The microstructural stability of this unidirectionally solidified alloy at elevated temperatures has been studied extensively.3.4 and preliminary tensile and bend tests have been reported. 5-7In the present investigation the tensile properties of the A1-CuA1, eutectic have been studied as a function of several ther-momechanical variables: solidification rate. heat treatment. rolling at elevated temperatures. and lamellar orientation. It was felt that the uniformity of structure and excellent interfacial bonding would give tensile properties concomitant with the metal matrix composite theory of strengthening proposed by Kelly and coson. 8-9 The tensile properties that were obtained point to a wide distribution of strengths for the CuAlZ platelets, which leads to large deviations from the predicted mechanical behavior for this composite. EXPERIMENTAL PROCEDURE Epitaxial Growth of Eutectic Alloy. The A1-CuA1, eutectic alloy was prepared by an epitaxial growth process. Sections of a master alloy ingot (total impurity content <0.008 pct) were placed in an alundum boat, melted. and directionally solidified to obtain a multigrained plate 12 by 2 by 4 in. This plate was tapered at one end to mate with a seed crystal 1; in. long and 4 by $ in. square. Then the seed-plate combination was placed in an alundum boat which sat in a quartz tube passing through the center of a horizontal resistance wound tube furnace. A dried argon atmosphere was maintained. The temperature gradient in the furnace was such that the liquid-solid interface of the eutectic alloy was located near the end of the furnace and could be observed through the quartz tube. Single-crystal plates were formed by melting the material back to the midpoint of the seed crystal of the desired platelet orientation and then epitaxially growing the plate from the seed by withdrawing the alundum boat from the furnace at a constant rate. This technique was used to produce aluminum and CuA12 lamellae parallel and perpendicular to the transverse direction on the plate. Metallographic examination showed that both phases were continuous across the original liquid-solid interface. It was also possible to grow a plate from two seeds placed side by side: and, although the lamellae of one seed were oriented at 90 deg to those of the second seed, the interface between the two grains remained parallel to the growth direction along the entire ingot length. Maintenance of a straight intergranular boundary during the solidification process was possible as long as both seeds were oriented with their original growth direction parallel to the solidification direction of the plate. Eutectic plates were directionally solidified at rates of 0.2, 1.0. and 4.7 cm per hr and sectioned transversely to the solidification direction to determine the apparent inter lamellar spacing of the lamellae. Metallographic examination was also employed

Jan 1, 1970

By I. R. Kramer

Studies of the effect of size of the specimen on the change of slopes of Stages I and 11 by surface removal showed that the change of Stage I was independent of size with respect to the polishing rate; however, the change in the slope of Stage 11 with polishing rate increased directly in proportion to the surface area. The removal of the surface during the test affected the plastic deformation characteristics of gold, aluminum, and zinc single crystals and polycrystalline aluminum. The apparent activation energy of aluminum was found to be decreased markedly by removing the surface during the deformation process. In previous papers1-3 it was shown that the surface played an important role in the plastic deformation of metals. By removing the surface layers of a crystal of aluminum by electrolytic polishing during tensile deformation, it was found that the slopes of Stages I, II, and III were decreased and the extents of Stages I and II were increased when the rate of metal removal was increased. By removing a sufficient amount of the surface layer after a specimen had been deformed into the Stage I region, upon reloading, the flow stress was the same as the original critical resolved shear stress and the extent of Stage I was the same as if the specimen had not been deformed previously. The slope of Stage I was decreased 50 pct and that of Stage 11 decreased 25 pct when the rate of metal removal was 50 X 10"5 ipm. These data show that in Stage I the work hardening is controlled almost entirely by the surface conditions, while in Stages 11 and III both surface conditions and internal obstacles to dislocation motion are important. It appears that during the egress of dislocations from the crystal, a fraction of them becomes stuck or trapped in the surface regions and a layer of a high dislocation concentration is formed. This layer would not only impede the motion of dislocations, but would provide a barrier against which dislocations may pile up. In this case, there will be a stress, opposite to that of the applied stress, imposed on the dislocation source and dislocations moving in the region beyond this layer. It has been found convenient to refer to this layer as a "debris" layer. The "debris" layer may be similar to the dislocation tangle observed by thin-film electron microscope techniques.4 Reported in this paper are the results of studies on the effects of removing the surface during plastic deformation on aluminum crystals of various sizes. The effects of the surface on the yield point behavior of gold and high-purity aluminum crystals as well as the creep behavior were also determined. The effects of surface removal on polycrystalline aluminum (1100-0 and 7075-T6) are also reported. EXPERIMENTAL PROCEDURE For those portions of the investigation involving creep and tensile specimens, single crystals, having a 3-in. gage length and a nominal 1/8-in. sq cross section, were prepared by a modified Bridgman technique using a multiple-cavity graphite mold. The single crystals were prepared from materials which had initial purities of 99.997, 99.999, 99.999, and 99.999 pct for Al, Cu, Zn, and Au, respectively. The aluminum specimens for the size effect studies were prepared through the use of a three-tier mold in which crystals having a cross section of 1/8, 1/4, and 1/2 in. were grown from a common seed. The mold design was arranged so that one 1/2-in. crystal, two 1/4-in. crystals, and four 1/8-in, crystals of the same orientation could be cast. With this technique, it was possible to obtain only one set of crystals with the same orientation. Because of this limitation, it was not possible to determine both the changes of extent and slope of the various stages since a large number of crystals of the same orientation would have been required. Instead, only the change of slope as a function of the rate of metal removal was studied by abruptly altering the current density of the electrolytic polishing bath at various strains within the regions of Stages I and 11. The experimental techniques used for the tensile studies were essentially the same as those used previously.1,3 The specimens were deformed in a 200-lb Instron tensile machine, usually at a rate of 10-5 sec-5. A methyl alcohol-nitric acid solution was used as the polishing bath for aluminum. The temperature was maintained constant within ±0.l°C by means of a water bath. The tensile machine was

Jan 1, 1963

By U. C. Tainton

THE world-wide continuation of low prices for zinc in 1934 has militated against any striking changes in the position of the metal. The price of zinc in London at the end of the year, about £11 5/8 per long ton, or 2.5c per pound at the existing rate of exchange, is more than 25 per cent below the average price for last year. In these circumstances probably the most significant event of the year was the putting into operation of the new electrolytic plant of the Giesches company at Magdeburg, Germany. This plant is designed to have an initial capacity of 20,000 long tons per year, and it is planned to increase this to 40,000 tons annually. This development is significant not only as indicating a continued swing of zinc metallurgy towards electrolytic methods, but also because it will make Germany virtually independent of foreign sources of zinc. This will mean that the zinc tonnage normally exported to Germany from Belgium and Poland will. become available for other markets, and it is feared may lead to lower prices unless the production of Bel-

Jan 1, 1935

By AIME AIME

TUESDAY afternoon the annual meeting was devoted to a general session, in the auditorium, on production control. George Otis Smith presided and in opening the meeting recalled that the session in 1920 on the stabilization of the coal industry was the first time this subject had been discussed by Institute members in a general session and then introduced Carl Snyder, of the Federal Reserve Bank of New York, who spoke on "Long-time Growth and the Factors In Its Variations." He spoke without notes and a full presentation of his views must be deferred until the stenographer&apos;s report is available. He said that of the total production some 80 to 90 per cent represents goods for consumption and the other 20 to 10 per cent for construction. He discussed various indices of production, concluding that bank clearings are the best, and showed by charts that when they are plotted, allowing for various disturbing factors, they are seen to increase quite regularly at the rate of about 4 per cent per year. The production curve rises at only 3y2 per cent per year, because agricultural production does not in- crease as fast as manufacturing postal revenues in- crease at the rate of 5 per cent per year while the use of electricity increases twice as fast.

Jan 1, 1929

By Eugene S. Machlin

A classical theory of solid solutions involving neavest-nergkbor intevactions with both central and linked-central forces between atoms has been developed. It has been found that the theory, where it can be checked quantitatively, is in ageement with experiment. The theory encompasses a description of many diverse pkenomena, such as antiphase shift structures, size effect, relative stabilities of various solutions, lattice para,neters, and order-disorder transitions. In particulav. a quantitative prediction not involving adjustable pavameters is made concevning the deviation of the Au-Cu interatonlic distance in long-range ordered (Ll,) Cu-Au I fronl the average distance based on the distances in pure gold and copper. This prediction, which is in agreement with expel-intent, has not been encompassed by any preuious theory. The theory of order-disorder is fragmentary. That is, no one theory exists that can explain the variety of qualitative phenomena observed. Further, many theories are not in good quantitative agreement with experiment. This subject has been reviewed by Muto and Takagi, Tuttman, and Oriani.3 There exists no doubt that the quasi-chemical approximation is not a complete description and that the inclusion of strain energy using macroscopic elasticity theory concepts leads to results in disagreement with experimenL4 The observation of antiphase domains and ordering systems such as Cu-Pt has led to Brillouin zone treat-ment of the order-disorder transition as opposed to the classical Ising model. The objective of this paper is to demonstrate that it is possible to develop a pairwise approximation model that can explain many of the observed order-disorder phenomena that have puzzled investigators in the past. This theory is based upon an empirical model due to ergmman&apos; for the elastic constants of metals. This model is generalized for multicomponent systems. As will be shown, the theory yields a short-range ordering energy for the disordered solution which differs from the ordering energy calculated from the differences in energy of disordered and long-range ordered solutions. It will be demonstrated that there is no necessary correlation between heats of formation and the tendency to order or between size effect and the tendency to order. Also, the existence of antiphase domains and iso-short-range-order systems that form superlattices (Cu-Pt) is predicted on the basis of the theory. Further, the relative stability of competing superlattices is calculable from the theory. If single-crystal elastic-moduli data are available for the pure components and one superlattice then there exists but one adjustable parameter in the calculation of lattice parameters for both the disordered and ordered solid solutions. In one special case, no adjustable parameters are required and a quantitative prediction is made. For the calculation of energies and partial order, there exists but one additional adjustable parameter, the pair-exchange energy V used in the quasi-chemical approximation (or the Ising model.) However, in these calculations, much more precise values are required for the single-crystal elastic moduli than available if the quantitative uncertainties in the predicted values of the energies are to be sufficiently small. THEORY ~er~man&apos; has developed a model with which he was able to obtain fair agreement with experiment for the relations between the elastic constants for metals. This model which we shall call Bergman&apos;s model is a linear combination of his models I and 11. In effect, Bergman, in this model, considers that each interatomic distortion is composed of two components: a classical central force distortion with an associated central force constant and what we shall call a linked-central force distortion with an associated linked central-force constant. The linked-central force distortion component obeys the constraint that the sum of such distortions over all the bonds equals zero. No constraint is imposed on the classical central force distortion component. Bergman&apos; derives the constraint on the linked-central force distortion on the basis of application of Pauling&apos;s relation between bond distortion and bond number to metals.ga This assumption is not logically necessary, however, and the Bergman model may be taken as a mathematical model for elastic constants, e.g., a purely empirical model without a physical basis. In the present work, the method of Bergman has been applied to two-component systems (solid solutions). In place of an external strain—which would allow a calculation of the elastic constants for the two-component system—it is considered that internal interatomic distortions exist as a consequence of having three potentially unequal distortion-free interatomic distances and but one "average" interatomic distance. It is assumed that the distortion-free interatomic distances between atoms of the same element are those found in the pure element having the same undistorted crystal structure as the solid solution. The distortion-free interatomic distance between unlike atoms is in general not measurable except in the probably nonexistent

Jan 1, 1967

By C. J. McHargue, J. C. Ogle

Lightly deformed columbiun single crystals which contained only parallel hoins or purullel and intersecting trains were annealed at 1000&apos; and 1600"C. No re-crystallizntion occurred in specimens hawing only parallel twins. Only noncoherent twin boundaries nzipated at 1000°C but both coherent and noncoherent ones moved al 1600°C. Recrystallization occurred within a few minutes at twin intersections at 1000°C. The orientation 01 the recrystallized grains differed front that of both the matrix and deformation twins, but could he derired by (110) and/or(112) rotations. ALTHOUGH twinning in metals has been extensively studied, there have been no definitive studies of the annealing behavior of crystals containing deformation twins. Some effects observed after annealing deformation twins have been summarized by Cahn1 and Hall2. Any or all of these phenomena are observed: 1) The twins may contract so that the sharp edges of the lens become blunted, and eventually the twin may disappear entirely. 2) The twins may balloon out at an edge, giving rise to a large grain having the same orientation as the twin. 3) The specimen may recrystallize; i.e., new grains are nucleated and grow at the expense of the twins and the crystal immediately adjoining the twin. Such grains have orientations which are not present before. Contraction has been observed in iron,3 titanium,3, 4 beryllium,5 zinc,8, 7 Fe-A1 alloy,&apos; and uranium.9 Long anneals at high temperatures are required to have any appreciable effect in these metals and only thin twins are absorbed. Lens-shaped twins are absorbed from the edges: the thin, almost parallel-sided twins are usually punctured in several places and each piece contracts independently. Absorption is very gradual and no sudden cooperative jumps have been observed. The expansion of a twin into a larger grain of identical orientation is unusual, but such growth has been observed in iron,"&apos;" zinc,6 and uranium." Crystals which have been deformed simultaneously by slip and twinning recrystallize first in the area adjacent to the twin. New grains appear faster where the twins intersect: but isolated twins, especially if thick, can also give rise to new grains. This type of recrystallization occurs in zinc.6, 7, 12, 13 and beryllium.14 Reed-Hill noted, in a single crystal of magnesium, the nucleation of a recrystallized grain at a twin intersection which had the same orientation as the second-order twin and which grew into the highly strained matrix.15 Short-time annealing has been reported to cause no change in the deformation twins in vanadium,16 columbium, 17, 18 tantalum,19 tungsten,&apos;&apos; and zinc.7 The purpose of this investigation was to note the effects of annealing on the coherent and noncoherent boundaries of deformation twins in columbium and to locate the nucleating sites for recrystallization. The orientation relationships, which the new recrystallized grains have with the parent crystal and the deformation twins, were also determined. EXPERIMENTAL PROCEDURE Single crystals of columbium were obtained by cutting large grains from electron-beam-melted buttons which contained 10 to 50 ppm C, 10 to 100 ppm O,, 1 to 10 ppm H2, and 10 to 15 ppm N2. The crystals were hand-ground and chemically polished until all grain boundaries were removed. The specimens were mounted in an epoxy resin and a face of each crystal was mechanically polished on a Syntron polisher using Linde A and then Linde B polishing compounds. After all faces were mechanically polished, the crystal was electrolytically polished to remove all distortion due to cutting and grinding. Laue photographs were taken of all faces of the crystals to determine the quality and orientation of each crystal. The crystals were compressed about 10 pct at -196 C in a specially constructed compression cage with an Instron tensile machine. Each crystal was separated from the top and bottom anvils by teflon films which acted as a lubricant. With the specimen crystal in position, the entire cage was cooled to -196°C by being submerged in a Dewar containing liquid nitrogen. The crystals were compressed at a rate of 0.02 in. per min and the load was recorded on a strip-chart recorder. After deformation the crystals were mechanically polished on 600-grit paper and Pellon cloth with Linde A and Linde B polishing compounds. The crystal faces were chemically polished and then etched. The twin planes were identified metallographically from an analysis of the twin traces on two surfaces. Annealing was carried out by placing each crystal in a columbium bucket made from the same electron-beam-melted material as the crystal itself and suspending the bucket by a tantalum wire in a quartz tube. After a vacuum of 10-7 Torr was attained, a furnace at 1000" or 1600 C was raised into position and the crystals held for various lengths of time. The crystals were repolished and etched after annealing to remove any surface contamination. Approximately 0.010 in. was removed during this process. The resulting surface was examined metallographically for microstructural changes due to annealing. A microbeam Laue camera mounted on a Hilger Micro-focus X-ray unit was used to determine the Orientstions of the recrystallized grains. This X-ray micro-beam camera had a 0.002-in.-diam collimator and incorporated the ideas of both and and chisWik21 and Cahn.22

Jan 1, 1967

By R. D. Pehlke, J. V. Gluck

A study was made of&apos; the effects of up to five additional solutes on the thermodynamic activity of zinc in dilute solution with molten bismuth in the range 450" to 650°C. The experimental measurements were made in a multielectrode galvanic cell apparatus employing fused LiCl-KCl as the electrolyte. The solute additions included indium, lead, tin, cadmium, copper, silver, antimony, or gold. A range of positice and negative interactiotls with zinc was covered. The experinzer~tal observations were cowlpared with the activity coefficients calculated usitlg either Wagner&apos;s first-order Taylor series rnodel or a proposed second-order solution itrteraction model. hi general, the truncated first-order Taylor series proposed by Wagner gaue good results for "dilute" solutions (XBi > 0.90) contaitzing up to six solutes. The second-order model, which includes a second-order cross-interaction term, produced a slight improvement in predictions for solutions with XZn = 0.015 and a significant improvement for solutions with XZn = 0.050 hear the limit of Henry&apos;s law region). Seveval of the quaternary solutions studied contained a total solute content of 0.215 mole fraction, and fairly good success was achieved in predicting the activity coefficient 01- zinc. ThE study of thermodynamic interactions between dilute solutes in liquid metallic solutions has occasioned much recent interest. It is useful to recall in this respect that Wagner&apos;s well-known expression for the activity coefficient&apos; is a practical application of the problem of representing a given function, i .e., In ?, by means of a sequence of polynomials. No specific physical model of a solution is involved in its use. As suggested by Wagner, a Taylor Series is used to expand In ? about a point of infinite dilution with respect to all solutes. The partial differential coefficients of the series have been termed "interaction parameters". Various authors&apos;-6 have proposed formalisms for parameters, the definitions being designed to meet some specific experimental or physical condition. A usual assumption is that terms above first-order in the Taylor Series may be neglected. In that case, the logarithm of the activity coefficient is expressed as a linear function of solute concentrations. The resulting expression is presumed valid for any number of additional solutes as long as the solution can be regarded as "dilute". This assumption can be termed "the hypothesis of additivity". However, experimental tests of that hypothesis for quaternary or higher-order solutions have been extremely limited. Primarily such tests have been confined to studies of effects of added metallic elements on either the activity of carbon or the solubility of gases in liquid iron.7-13 The only known previous study of an all-metal system is the limited work of Okajima and pehlke14 on the effects of multiple solute additions on the activity of cadmium in liquid lead. The present investigation is a portion of the work to determine the effects of various solute additions on the activity of zinc in dilute solution with molten bismuth in the range 450" to 650C It was shown for such ternary solutions that second-order Taylor Series terms could be evaluated at the same time as first-order terms, with no additional experimentation required. A second-order solution model was described which, under certain conditions, is a rigorous representation of solute activity in a ternary solution. (In the sense employed in this paper, the term "model", as distinguished from "equation", is taken to mean an empirical correlation or formalism, but not a hypothetical physical system per se.) Presumably such a model could be extended to produce a better representation of In ? in solutions of even higher order. The feasibility of a generalized Taylor Series approach to solution interactions and inclusion of second-order terms also has been discussed recently by Lupis and Elliott in independent work concurrent with the present investigation. In addition, they discussed empirical means of estimating certain second -order coefficients.17 The utility of such solution models rests on the ability of a truncated series to represent adequately the experimental facts in multicomponent solutions. Questions that arise include: Do the second-order terms really make a significant contribution? How far away from "dilute" solution may such models be applied? Are the types and varieties of the additional solutes important? among others. In order to provide some answers to these questions, an experimental study was made of the effects of two or more additional solutes on the activity of zinc in dilute solution with molten bismuth. Comparisons were then made with calculated activity coefficients obtained using the previously determined ternary interaction parameters. INTERACTION MODELS As an example of the approach to defining activities in multicomponent solutions, consider the Taylor Series expansion for a quaternary system, i.e., three dilute solutes. Writing terms through second order, the result is:&apos;&apos;

Jan 1, 1968

By E. I. Gordon

The electronic pickup tube is the image-to-video signal-converter or transducer in tele vision-like systems. Images may relate to visible light or IR excitation as in conventional TV systems, X-ray excitation as in some medical and production control applications, or electron excitation as in electron microscopy. The latter process is also important in some forms of light or X-ray sensitive pickup tubes as an intermediate step. In virtually all of these devices the image ends up as a stored charge pattern on a suitable target electrode and the video signal is created by periodically scanning the target with a low energy electron beam and removing the stored charge. In a major group of tubes radiation induced conductivity creates the charge pattern. In others, photoemission is used. In this paper an attempt is made to illuminate some of the device requirements placed on materials exhibiting radiation induced conductivity, some of the materials and techniques that are used, and the problems. The emphasis will be on visible light and IR sensitive targets although some attention will be given to X-ray and electron imaging. Photoconducting films as well as diode arrays will be discussed. ELECTRONIC pickup tubes find their greatest use in commercial, entertainment television, and in industrial and educational closed-circuit television. Video telephone systems, such as AT&T&apos;s PICTURE-PHONE System will become eventually the greatest user. Military use is also very important. Nevertheless the use of electronic pickup tubes in technology, science, and medicine is assuming ever greater relevance and demands the greatest diversity and perfection in the pickup tube art. Commercial television and closed-circuit television use requires visible light response, high resolution, low lag, and uniform response. Video telephone use requires the same plus extreme reliability, stability, and low cost. Military use emphasizes, in addition, sensitivity, IR response, and ruggedness. (Devices for far IR response will not be considered here.) The use of pickup tubes in medicine and biology emphasizes UV response for microscopy, X-ray response for radiology, and energetic electron response for electron microscopy. Astronomy and nuclear physics demands low light level response, storage ability, and resolution (here the tube is a successful replacement for film). The interested reader might profitably read Advances in Electronics and Electron Physics, vol. 12,&apos; 16,2 and 22A3 and 22B4 for detailed discussion of the use, properties, and technology of electronic pickup tubes. In general, because of the importance of these uses, none of the above properties will be ignored. Nevertheless attention will be restricted to only those imaging devices, called pickup tubes, using a scanning electron beam to dissect the image with a resulting video signal for conventional CRT display. However pickup tubes have become so complex that many of them include components such as image in-tensifiers which would be normally excluded by this restriction. Thus some of the other imaging devices will not be ignored entirely. We will first review the fundamental elements and physical phenomena involved in modern electronic pickup tubes, then the relevant materials and some of the material problems and then an interesting goal yet to be achieved. REVIEW OF PICKUP TUBE PRINCIPLES In all modern television systems using pickup tubes there is an interval called the frame interval, during which the incoming radiation flux is allowed to produce a cumulative effect in the form of a stored charge pattern which is a replica of the radiation image, and a scan interval during which the stored charge pattern is converted into a video signal. The frame interval bears no fixed relation to the scan interval and may be shorter or longer. In conventional, real time television the scan interval including retrace is identical to the frame interval. Integration and storage is the key to the sensitivity of modern pickup tubes, in contrast to earlier tubes such as the image dissector. At equivalent light levels and without integration, the number of photons contributing to the video signal in the image dissector is lower by a factor approximating the number of picture elements in the displayed image, a number of order 10. Statistical fluctuations in the number of contributing photons represent a serious limitation to the attainable signal to noise ratio, resolution and contrast. As a result considerably greater light levels have to be used then in targets which integrate over the full frame period. Thus the crucial elements, common to all modern pickup tubes, are the charge storage surface and the scanning electron beam which is incident on the charge storage surface at very low energy. These are shown in Fig. 1(a). The charge storage insulator is generally very thin with a thickness of several microns or less. The surface of the insulator is held near cathode potential. The backplate potential is held at cathode potential or at a small positive voltage relative to cathode. The combination of storage insulator and backplate electrode is commonly called the "target". In the absence of incident radiation flux the electron beam scans over the storage surface depositing negative charge uniformly over the scanned part of the surface by virtue of the fact that the effective secondary

Jan 1, 1970

By E. W. Johnson, M. L. Hill

Cold working of iron-carbon alloys was found to increase greatly the hydrogen solubility and to decrease the diffusivity at temperatures up to 400° C. These effects are increasing functions of both the carbon content and the degree of deformation. The hydrogen behavior is consistent with the idea that cotd working creates "traps", which are concluded to be microcracks in which the hydrogen is chemisorbed. Hydrogen embrittlement is explained by the Petch theory of metal crack surface energy loss due to hydrogen adsorption. HYDROGEN embrittlement of steel has been studied for many years and has been the subject of an extensive literature, but the mechanism of the effect has not been completely understood. The embrittlement is unusual in that the ductility loss is not accompanied by an increase of the yield strength, being primarily a decrease of the fracture strength alone. The loss of fracture strength is usually most severe in the temperature range between 0°and 100°C. Here the solubility of hydrogen in the iron lattice at ordinary H2 pressures is extremely low while the diffusivity is still quite high. From the relationships between the ductility and the hydrogen content, test temperature and strain rate, it is apparent that the hydrogen atoms causing the ductility loss difbse to and concentrate in small regions of the metal which are especially susceptible to the initiation and propagation of fracture. This hydrogen segregation apparently occurs after plastic straining has begun. Below 0°C the ductility loss persists only at low strain rates in confirmation of the view that the embrittlement is diffusion .controlled. The tendency of the embrittlement to disappear above 100°C can be explained by the increasing lattice solubility of hydrogen with rising temperature. A common view of hydrogen embrittlement of steel is that the hydrogen initially dissolved in the metal lattice diffuses to structural discontinuities and there precipitates as H2 gas at very high pressures which assist the external stress in causing premature failure.1,2 The idea of a high H2 pressure in equilibrium with ordinary amounts of hydrogen in steel at room temperature is due to observations of hydrogen behavior in fully annealed material, for which the Sieverts&apos; law constant relating solute concentration to H2 pressure is extremely small. Hydrogen-embrittled steel, however, is always plastically deformed to some extent, and therefore it is important that hydrogen embrittlement be explained primarily in terms of hydrogen behavior in plastically deformed material. Such an explanation is attempted in this paper. Previous studies of hydrogen in cold-worked steel have shown that both the solubility and the diffusion rate are significantly chaned when the steel is cold worked. Darken and Smith discovered that the amount of hydrogen absorbed from acid by cold-rolled steel at 35°C is many times greater than that absorbed by hot-rolled steel. They found also that the hydrogen permeability of the steel is unaffected by cold working. Keeler and Davis4 confirmed the high apparent solubility of hydrogen in cold-worked iron-carbon alloys at temperatures up to and even beyond the recrystallization temperature. They also found that this solubility increase accompanying cold work is a sensitive function of the carbon content, being absent when no carbon is present. The present experimental study was undertaken primarily to obtain an improved understanding of the behavior of hydrogen in cold-worked steel. Data were obtained on the effects of temperature, H, pressure, carbon content, and degree of cold work on the hydrogen solubility and diffusivity in iron-carbon alloys. These data have been helpful in elucidating the nature of the cold-worked steel structure as well as in providing information on the mechanism of hydrogen embrittlement of steel. EXPERIMENTAL Cylindrical specimens for hydrogen absorption and diffusion rate measurements were prepared from three iron-carbon binary alloys and a commercial SAE 1010 steel. The iron-carbon alloys were prepared by vacuum melting electrolytic iron with graphite in a magnesia crucible. The alloys were cast in vacuum as 2 1/2-in. sq ingots weighing about 20 lb each. The ingots were hot rolled (above 1900°F) to 5/8-in.-diam round bars and then cooled in air to room temperature. The resulting metallographic structure consisted of islands of fine pearlite surrounded by free ferrite. Chemical analyses of the materials are given in Table I. The 5/8-in. diam bars were turned to diameters such that cold reduction to the desired final specimen diameters would result in either 30 or 60 pct reduction in area (RA). The machined bars were then cold worked by swaging at room temperature

Jan 1, 1960

By K. A. Natarajan, I. Iwasaki

Platinum electrodes are not inert as often thought to be. The reactivity of platinum electrodes can explain their erratic behavior in many electrochemical measurements of metallurgical interest, e.g, in flotation systems, streaming potential measurements, contact-angle measurements, and in leaching systems. The anomalous behavior of platinum electrodes in redox potential measurements in aqueous systems was studied through Eh and pH measure ments in water-oxygen, iron-water-oxygen, and manganese-water-oxygen systems. Stability relations between Fe++ and Fe (OH), and between Fe (OH), and Fe (OH), were studied to judge the correspondence between experimental and theoretical equilibrium lines. The practicality of redox potential measurements in estimating ferric-ferrous ratios in aqueous systems was investigated along with their suitability as indicators in leaching operations, e.g., the removal of iron by aeration from manganese leach solutions. Platinum electrodes have often been used in the measurement of dissolved oxygen concentrations and of redox potentials (Eh) in a variety of fields, e.g., analytical chemistry,&apos; corrosion," geology and mineralogy,,&apos;&apos; biology,"&apos; sewage treatment,&apos; * hydrometallurgy,"I" and flotation."la The effectiveness of Eh-pH diagrams, first reported by Pourbaix&apos; in 1949, has contributed much towards the theoretical understanding of numerous problems encountered in the metallurgical industry. Not many references are available in the literature, however, wherein attempts have been made to confirm Eh-pH diagrams from experimental measurements. One reason might be that, in spite of the apparent simplicity of the electrochemical technique, the direct measurement of Eh involves complex practical problems.&apos; Factors such as the purity of the solution, the type of electrodes used, the history of the indicator electrode, and the type of atmosphere (namely, oxidizing, reducing, or inert) do have effects on the measured Eh values. The influence of mixed potentials cannot be underestimated. The poisoning of platinum electrodes by organic and inorganic impurities present in the solution may lead to erratic results. Platinum, commonly thought to be an inert electrode material, is not really so, as attested by a number of previous investigators who advised caution concerning the anomalous behavior of platinum electrodes in various electrochemical measurements.&apos;" In the present article, a few pertinent experiments related to Eh-pH measurements in systems of interest in the metallurgical and water pollution fields are described in an attempt to correlate such information with what is already known, especially in the electrochemical literature. Iron-water and manganese-water systems were selected with a view of studying the correspondence between experimentally observed and theoretically established equilibrium lines. The work included an investigation of the behavior of platinum electrodes with respect to pretreatment and adsorption characteristics, the measurement of dissolved oxygen concentrations and their relation to Eh, the determination of the electrode potential of the ferric-ferrous couple at different pH, and the measurement of oxidation potentials in iron-manganese leaching systems. Experimental Procedure A rotating platinum electrode was used in many of the measurements to study the effect of rotation on measured Eh values. The electrode made by the Pine Instrument Co. consisted of a stainless steel rod with a platinum disk soldered to the end. It was covered with a Teflon insulation along the sides, so that only the circular tip of the electrode was exposed to the solution. Prior to its use, the platinum surface was brightened on a metallurgical polishing wheel with alumina as an abrasive, unless specified otherwise. The electrode was rotated with a Sargent cone-drive motor at 350 rpm. The contact of the electrode with the external circuit was made by filling a notch at the top of the stainless steel shaft with mercury and by dipping a copper wire into the mercury pool. The performance of the rotating platinum electrode was compared with the performances of a Beckman platinum button electrode and a platinum wire electrode. All the potentials were measured with respect to a saturated calomel electrode. A saturated KC1-agar bridge was used to minimize the liquid junction potential. A Beckman Zeromatic pH meter together with a Beck-man electrode switch was used to measure both the Eh and pH. A double-walled, all-Pyrex jar with a capacity of about 1 liter and themostated by circulating water of constant temperature was used for a reaction cell. Four equally spaced ports in the cover provided access for a glass electrode, a salt bridge connecting the saturated calomel electrode, a dispersion tube for bubbling gases into the cell solution, inlet and outlet tubes for passing the desired gases over the solution, and a graduated burette for introducing reagents from outside. The rotating platinum electrode was inserted through an opening in the top-center of the cover, and a positive gas pressure was maintained inside the cell to prevent air from entering into the cell compartment. A magnetic stirrer was used to mix the solution inside. For the determination of dissolved oxygen in the test solutions, the polarographic techniquex was used.

Jan 1, 1971

By Hsun Hu, B. B. Ruth

The rates of migration of high-angle boundaries in zone-refined aluminum crystals rolled 20 to 70 pct in the (110)[i12/ orientation were studied. Following a recovery anneal at an appropriate temperature to stabilize the polygonized structure, boundary migration rates of artificially nucleated grains were measwed isothermally at several temperatures. Results indicate that the rate of boundary migration depends strongly on the amount of deformation and on the cell size of the polygonized matrix, and is related to the driving free energy by a power function. The degree of anisotropy in growth 0.f the re crystallized grains nn&apos;th preferred mientation is independent of deformation; the migration rates of the fast-moving and the slow-moping boundary segments of a gowing grain differ by as much as one order of magnitude. The actir\ation energy fm a grain boundary migration, although nearly the same for both the fast-moving and the slow-moving boundaries for a given deformalion, decreases from 45 to 30 kcal per mole with an increase in deformation from 20 to 70 pct reduction. Re crstallization by the growth of the artificially nucleated grains results in preferred orientation. The Percentuge of&apos; grains favorably oriented for growth increases with increasing deformation. None of these grains corresponds to the ideal Kronberg-Wilson orientation relationship. The observed growth aniso-tropy is discussed in terms of boundary structure. The boundary velocity as a function of the cell inter -facial area, or the driving free energy, is discussed in the light of current theories of boundary migration. It is well established that recrystallization with re-orientation occurs by the migration of high-angle boundaries of strain-free grains. The driving force for this process is provided by the free energy stored in the metal during deformation. A quantitative study of the effect of varying driving force on grain boundary migration in deformed metals has not been possible heretofore, primarily because of: 1) concurrent recovery steadily decreasing the available driving free energy for boundary migration, &apos;-3 and 2) in-homogeneity of strain in the deformed metal.4 Aust and Rutter3 studied grain boundary migration in striated single crystals of zone-refined lead. Although the driving free energy in such crystals remains unaltered during annealing, this method does not provide a range of driving free energies over which measurements of grain boundary migration can be made. In the present investigation, the rates of migration of high-angle boundaries in deformed aluminum zone- refined single crystals were studied at various temperatures, after deformation ranging from 20 to 70 pct reduction by rolling at -78°C in the (ll0)[i12] orientation. The boundary migration rates along different crystallographic directions were determined under steady-state conditions, i.e., in the absence of competing recovery processes or impingement of recrystallized grains growing into the deformed single crystal matrix. Simultaneous recovery was eliminated by suitable anneals prior to the boundary migration measurements. The recrystallized grains, which grew a ni so tropically into the homogeneously polygonized matrix, developed flat boundary segments during early stages of growth. These boundary segments subsequently migrated along a direction approximately normal to the boundary plane into the matrix rystal. Increasing deformation over the range employed was estimated to increase the driving free energy for boundary migration by about five times. The kinetics of the boundary migration process, examined under these conditions, indicate that the boundary velocity is greatly affected by a small change of the driving free energy in the matrix crystals. These results were examined in the light of the current theories of grain boundary migration. EXPERIMENTAL PROCEDURES Single crystal strips (9 by 1 by 0.125 in.) of zone-refined aluminum, were seed-grown by the Bridgman method in a high-purity graphite mold (<lo ppm ash) at 1 in. per hr. Precautions were taken to minimize contamination of the metal during crystal preparation and subsequent handling. Spectrographic analysis of the metallic impurities in the grown crystals is Qven in Table I. The crystals were rolled in the (110)[112] orientation at -78°C to various reductions in thickness, ranging from 20 to 70 pct, in 10 pct increments. The desired reduction was achieved by many rolling passes, each being no more than 0.002 in. To minimize surface friction, the crystal was rolled between two thin layers of teflon. For those crystals rolled more than 40 pct, it was necessary to remove the disturbed surface layers by electropolishing at -5" to -10°C at an intermediate stage of rolling. The edges of deformed crystals were removed by a jeweler&apos;s saw while submerged in alcohol at -78° C to obtain samples of about ? by i in. The distorted metal at the cut edges and the surface layers were then removed by electropolishing, with removal of a minimum of 0.004 in. from each surface. The thickness of the crystals prior to rolling was chosen so that the final thickness was 0.025 in. for all samples. These deformed single crystals were each prean-nealed for 1 hr at an appropriate temperature in the range of 130" to 280°C, depending upon the amount of deformation. The purpose of this preannealing was to

Jan 1, 1970

By E. T. Turkdogan, J. H. Swisher

bi the fivst part of the paper results ave given on the rate of decarburization of Fe-C melts ln CO2-CO atmospheres at 1580°C. The rate -controlling step is believed to he that irvlloluing dissociation of curbotz dioxide on the suvfuce of the melt. 4 genevral reaction mechanistm is poslnlated jor gels-t11eta1 veactions oc-curit~g on the surface of iron coutcotamncited with chemi-sovbed osygesL. Oxygen the present work on decavbuvization of liquid iron and previous studies on the kinetics of nitrogen absorption and desorplion are discussed in terms of the postulated mechanism, ManY of the early studies of rate of decarburization of liquid steel were of an exploratory nature and laboratory exppriments carried out pertained to open-hearth or oxygen steelmaking processes. References to previous work on this subject may be found in a literature survey made by Ward. Using more sophisticated experimental techniques, several investigators have recently studied the kinetics of decarburization of molten Fe-C alloys in oxygen-bearing gases. For example, Baker et al2.&apos; reported their findings on the rate of decarburization of liquid iron, levitated by an electromagnetic field, in carbon dioxide-carbon monoxide-helium atmospheres. In these levitation experiments the samples used were small in size, e.g., -0.6-cm-diam spheres weighing -0.7 g, and the rates were measured for decarburization from about 5 to 1 pct C at 1660°C. The rates obtained under their experimental conditions were considered to be controlled primarily by gaseous diffusion through the boundary layer at the surface of the levitated melt. Parlee and coworkers3 measured the rate of absorption of carbon monoxide in liquid iron. The rates were found to follow first-order reaction kinetics, yielding a reaction velocity or a mass transfer coefficient in the range 0.2 to 0.4 cm per min. The coefficient was found to decrease with increasing carbon content of the melt. These investigators attributed the observed rates to the transfer of carbon or oxygen through the diffusion boundary layer adjacent to the surface of the melt. In the work to be reported in this paper, an attempt has been made to study the kinetics of gas-metal surface reactions involved in the decarburization of liquid iron. EXPERIMENTAL The experiments consisted of melting 80-g samples from an Fe-1 pct C master alloy in an induction furnace and decarburizing in controlled CO2-CO mixtures at 1 atm pressure and 1580°C. The master alloy was prepared by adding graphite to electrolytic "Plastiron" melted in racuo. None of the impurities in the master alloy exceeded 0.005 pct. The reacting gases were dried by passage through columns of anhydrone; in addition, CO2 impurity in carbon monoxide was removed by passage through a column of ascarite. A schematic diagram of the apparatus is shown in Fig. 1. A 1.25-in.-diam recrys-tallized alumina crucible containing the sample was placed inside a 3-in.-diam quartz reaction tube, all of which was surrounded by an induction coil. A 450-kcps induction generator was used as the power source. Water-cooled brass flanges, which contained the gas inlet, gas exit, and sight port, were sealed to the top of the reaction tube with epoxy resin. The reacting gases were metered with capillary flowmeters and passed through a platinum wire-wound alumina preheating tube, 0.25 in. ID and 11 in. long. The gases were preheated to about 1300°C. A disappearing-filament optical pyrometer was used to measure the melt temperature. The pyrometer was initially calibrated against a Pt-6 pct Rh/Pt-30 pct Rh thermocouple. The temperature was controlled to within +10°C by manually adjusting the power input to the induction coil. In a typical experiment, an 80-g sample of the master alloy was melted in a CO2-CO atmosphere having pcO2/pco = 0.02 and flowing at 1 liter per min. A negligible amount of carbon was lost and no significant reduction of alumina from the crucible occurred during melting, e.g., 0.005 pct Al in the metal. After reaching the experimental temperature of 1580°C, the gas composition was changed to that desired for a particular series of decarburization experiments. The duration of the transient period for obtaining the desired gas composition at the surface of the melt was about 20 sec . The flow rate of the reacting gas was maintained at 1 liter per min. After a predetermined reaction time, the power to the furnace was turned off. During freezing, which took about 10 sec, the amount of gas evolution was not sufficient to result in a significant loss of carbon. The samples were analyzed for carbon by combustion and in a few cases they were analyzed for oxygen by the vacuum-fusion method. RESULTS A marked increase in the rate of decarburization of iron with increasing pcO2/pco ratio in the gas stream is demonstrated by the experimental results given in Figs. 2 and 3 for pco2/pco ratios from 0.033 to 4.0. In one series of experiments, denoted by filled triangles in Fig. 2, the reacting gas was diluted with argon (48 vol pct) resulting in a slower rate of decarburization. Samples from two series of experiments with pco2/pco = 0.033 and pco2/pco = 0.10 (with argon dilufion) were analyzed for oxygen. In these Samples the oxygen content increased with reaction time

Jan 1, 1968

By Charles L. Mantell, James E. Hoffmann

Mechanical inclusion, electrophoretic deposition, and adsorption were studied as mechanisms for code-position of aluminas present in copper-plating electrolytes as an insoluble disperse phase. Mechanical inclusion was not a significant factor. That codeposi-tzon of aluminas by an electrophoretic mechanism was unlikely was substantiated by measurements of the potential of the aluminas. The alumina content of the deposits was studied as a function of the pH of the bath. These tests in conjunction with sedimentation studies demonstrated the absence of an isoelectric point for the alutninas over the pH range examined. Thiourea in the electrolyte (a substance known to be adsorbed on a copper cathode during electrodeposition) affected the amount of alumina in the electrodeposit. However, no adsorption of thiourea on aluminas in aqueous dispersions was detected. If it were possible to produce a dispersion-hardened alloy of copper and alumina by electrodeposition, an alloy possessing both strength and high conductivity at elevated temperatures might be anticipated. Investigation of the mechanism of codeposition of aluminas with copper was undertaken with the hope that knowledge of the mechanism would aid in the development of such an alloy. The word "codeposit" here does not necessarily imply an electrolytic phenomenon but rather that the materials codepositing, the various aluminas, are transported to and embedded in the electrodeposited copper by some means. Mechanical inclusion in electrodeposition implies a mechanism of codeposition which is wholly mechanical in nature; the only forces acting on a particle are gravity and contact forces. Such a particle is presumed to be electrically inert and incapable of any electrical interaction with electrodes in an electrolytic plating bath. Processes for matrices containing a codeposited phase by electrodeposition from a bath containing a disperse insoluble phase frequently state that code-position is caused by mechanical inclusion.10,2,12 If settling, i.e., gravity, be the controlling mechanism for codeposition of aluminas, then assumptions may be made that 1) the content of alumina in the electrodeposit should be enhanced by increasing the particle size, 2) the geometry of the system, that is, the disposition of the cathode surfaces relative to the di- rection of the falling particles, should affect the alumina content of the electrodeposit, 3) in geometrically identical systems the chemical composition of the electrolyte employed should exercise no effect on the alumina content of the deposit, that is, the alumina content should be the same in all cathode deposits irrespective of bath composition. A bent cathode19 evaluates the clarity of filter effluent in electroplating baths by comparing the roughness of the deposit on the vertical surface with that on the horizontal surface. Two difficulties are inherent in this technique: 1) the current density on the horizontal portion of the cathode would be substantially greater than that on the vertical surface; 2) should the deposit obtained be rough, projections on the vertical face could act as horizontal planes and vitiate the relationship between the vertical and horizontal surfaces. Bath composition should have no substantial effect on the alumina content of the deposit. Two different electrolytic baths were employed. They possessed variant specific conductances and substantially different pH ranges. The experimental tanks were rectangular Pyrex battery jars 6 in. wide by 3 1/4 in. long by 9 3/4 in. deep. The cathodes were stainless steel 316 sheet of 0.030 in. thickness, cut to 7.5 by 1.75 in. and bent at right angles to form an L-shaped cathode whose horizontal surfaces measured 1.75 by 3.0 in. All edges and vertical surfaces were masked with Scotch Elec-troplaters Tape No. 470. The anodes were electrolytic cathode copper 9 in. high by 2.25 in. wide by 0.5 in. thick. To eliminate inordinately high current densities on the projecting edge of the cathode, the anode was masked 1 in. above and below the projected line of intersection of the cathode with the anode. The exposed area of the anode was equal to that of the cathode, providing both with equal average current densities. The agitator in the cell was of Pyrex glass and positioned so its center line was equidistant from cathode and anode, and a plane passed horizontally through the center of the blade would be located equidistant from the bottom of the cathode and the bottom of the deposition tank. The assembled apparatus is depicted in Fig. 1. Hatched areas on anode and cathode represent the area of the electrodes wrapped with electroplaters tape. MATERIALS The chemicals were copper sulfate—CuSO4 • 5H2O— technical powder (Fisher Scientific Co.). Spectro-graphic analysis showed substantial freedom from antimony, arsenic, and iron. Traces of nickel were present.

Jan 1, 1967

By F. B. JEWETT

TWENTY FIVE years of doing, finding, and encouraging others to do scientific research in&apos; industry, and of organizing the machinery for the` smooth &apos;and effective conduct of such research, have left me with a feeling that so far as this branch of human activity is concerned the problems in &apos;essence are- not, materially &apos;different from those met elsewhere. Years ago, in a less mature period of life, I may have thought that the effective industrial research man was a being somewhat different from his fellow workers in adjacent &apos;fields, but I have long since &apos;changed my views. The rank and&apos; file of the modern industrial research organization are relatively easy to find, though some¬times difficult to get in sufficient numbers. Mistakes in choosing them are not particularly serious to the or¬ganization, however unfortunate they may be for the misplaced individual who persists too long in the wrong environment. The reason for this is obvious from the fact that, taken by and large, the work of the rank and file is at best necessarily a work of detail done under guidance of the more experienced. In this respect the situation of the rank and file in an industrial research organization is not different from that class in any other group activity, whether concerned with industry, the university, or the church. This does not mean, however, that we are not all anxious to have the best possible material obtainable in the rank and file, or that we are indifferent to the utmost of encouragement and stimulation to its individual members.

Jan 1, 1929

By W. L. Penberthy, H. J. Ramey

Experimental work on the combustion oil recovery process has consisted of both laboratory and field studies. Although field experiments are the ultimate test of any oil recovery process, they are costly, time consuming and difficult to analyze quantitatively. Laboratory combustion tube experiments can be opertzted far more rapidly and cheaply, but are subject to scaling and interpretation problems. This paper points out some important design problems, operational criteria and considerations in2portunt to interpretation of results. An analytical hcut model of movement of a burning front axiully along a cylinder with heat loss through an annular insulation was developed. The result was used to identify steady-state temperatrrre distributions both ahead of and behind the burning front, with and without heat loss. Results indicate potential operating limitations on the minimum burning front rielocity (or air flux) which may be used for any given combustion tube. Results also enable estimating the effective thermal diffusivity and over-all heat loss from experimental data and thickness of the brnning zone. Resu lts of operation of a combustion tube constructed recently verify this preliminary theory in the region immediately ahead of and behind the burning front surprisinRly well. INTRODUCTION Many field and laboratory studies of the forward combustion oil recovery process have been conducted since the early publications of Kuhn and Kochl and Grant and Szasz2 in 1953 and 1954. In view of the complex and costly nature of this type of investigation, it is not surprising that no complete theory of the nature of the forward combustion Drocess is yet available. However, gross effects are understood well enough that reasonable design procedures are available for planning field operations. Nelson and McNeil 3,4 have published two comprehensive papers concerning design procedures. One major consideration in planning field operations is the fuel concentration at the burning front. Fuel concentration controls air requirements — an important cost factor in forward combustion. Although fuel concentration can be estimated from field test results by various methods, results are subject to great uncertainty in view of natural limitations on experimental observations. Nelson and hlcNeil4 recommend that fuel concentration be determined from laboratory combustion tube studies. Fuel concentration is only one of many important factors which can be studied by combustion tube experimentation. An obvious goal of imporrance must be development of a comprehensive theory of the forward combustion process. If a theory of this process can be established which matches controlled laboratory experimentation, it should be possible to apply this theory to field operating conditions with some confidence. Laboratory combustion tube studies have already yielded important information concerning the combustion process. However, details concerning the design, construction and operation of combustion tubes are rare. Combustion tubes used by various investigators vary in size, length and mode of operation. Therefore, one purpose of this paper is to present considerations important to design, construction and operation of a combustion tube. In regard to previous combustion tube studies, attention is called to Refs. 1 through 9. These references describe a wide variety of equipment types and present a great deal of pertinent experimental data. In general, combustion tubes usually consist of thin-walled stainless steel tubes containing an oil sand pack mounted within a pressure jacket. Provisions have often been made to heat the tube ex tern a lly by separately controlled heaters to reduce heat losses. This step usually permits operation at low air fluxes (air rate per square foot burning front surface) similar to those encountered in field operations. Burning is usually conducted from the air inlet end of the tube to the outflow end. The tube orientation used has been vertical or horizontal. For vertical tubes, burning has been conducted vertically downwards. As a result of laboratory studies, many of the

Jan 1, 1967

By W. S. Gillam

A need for new supplies of fresh water exists today and in many specific areas that need is urgent. One solution lies in saline water conversion, a problem complicated by cost factors. The principles involved in saline water conversion, the status of development, and the estimated costs (present and future) of several processes are presented. Among the methods discussed are distillation, electrodialysis, and freezing. In general, the costs presented are based on a standardized procedure for estimating conversion costs, permitting a valid comparison among the various processes. The need for new supplies of fresh water and the potential benefits to be derived from an abundant supply of converted water are recognized by practically everyone concerned with water problems. The water supply problem exists today; it is urgent in many specific areas in this country and also in the world, and it will become more acute in the future. One answer to the growing problem of adequate water supplies is the development of new sources. Very significant quantities of brackish underground and surface waters exist in certain areas and an inexhaustible supply of ocean water is available. Thus in many areas water resources can be extended through saline water conversion. Congress recognized the need for new sources of fresh water in 1952 and passed the Saline Water Act, Public Law 448, amended it in 1955, and in September 1958, enacted Public Law 85-883, calling for the construction of at least five demonstration plants. The program is administered by the Dept. of Interior through the Office of Saline Water, and its primary objective is to reduce the cost of converted water produced, whether it be by development of new processes or improvement of known processes. This is a most difficult problem and one that will require several years of prodigious effort. It is difficult—not because of any intricate or new chemistry, engineering, or physics involved—but because of the difficulty in converting water at low cost. Whatever the sources of the saline water, the salts which are held tenaciously in solution must be removed before the water becomes suitable for industrial or domestic uses. Saline water is a relatively simple system of salts dissolved in water. It has certain chemical and physical properties that determine the various methods by which the salts may be separated from the water. The system, although not complex, in most instances, has had countless years in which to reach equilibrium and is, therefore, comparatively stable. Because of its stability, separation of saline solutions requires relatively large quantities of energy. The unique properties of water depend on the fact that its molecules are chemically active. The chemical and physical properties of water are associated with the type of bonding involved in the water molecule. Chemical changes such as hydrolysis, or rusting of iron, involve the breaking of chemical bonds between the hydrogen and oxygen atoms. Physical changes, such as evaporation in a boiler, the melting of ice, or the viscous resistance to flow in a pipe, involve breaking of the hydrogen bonds. (The hydrogen nucleus is so small that it can attract two negative atoms.) Thus water molecules not only combine with molecules of other compounds but even with one another; e.g., each molecule may be bounded to four other molecules. Water molecules cling to the ions of dissolved salt to form water-encumbered hydrated ions and they cling to one another to form entangling networks through which hydrated ions can be propelled only by tearing the networks apart. That is one reason why considerable energy still needs to be expended in our simplest procedures for purifying water. If water molecules did not have this habit of clinging so tenaciously to other molecules, and to one another, it would be easy to push salt ions past the water molecule and get a separation. But the water would not then dissolve salt, so the problem would not exist.&apos; Water when heated evaporates very slowly, relative to other liquids having simple molecules. Vaporization involves the separation of molecules from the liquid, and this means overcoming the attraction between molecules which is due to the hydrogen bonding. The heat of vaporization for water is high; consequently, the boiling point of water is also high. Water boils at 100" C; hydrogen sulfide (H2S) at -60" C; oxygen (02) at -183" C; nitrogen (N2) at -196" C; and methane (CH4) at-161°C, even though the latter has about the same molecular weight as water. Because of these peculiar properties of water, it exists as a liquid on earth instead of a gas such as hydrogen sulfide or nitrogen and oxygen.

Jan 1, 1961

By Henry M. Otte, Ralph P. I. Adler

The changes of line position and integral line breadth in the X-ray diffraction pattern of a polycvys-talline Cu-30Zn tensile test piece, incrementally loaded (and unloaded) up to fracture, have been an-alyzed in detail. The stacking-fault probahility, cv, increased linearly with increasing strain, E, wheveas the effective domain size, De(hkl), decreased with decreasing E-1 Over the greater part of the stress-strain curve the rate of work hardening was essentially constant (about 86 kg per sq mwz), and could be correlated with the slope of stage II of the single-crystal stress-strain curve. Consequently the theories of work hal-dening (particularly those parts relating to stage 11) as developed by Mott and Hivsch and others could be applied to the observations made on the polycrystalline brass. A relationship of the form Aa = Aao - MhklEhkl between the change, Aa, in the extrapolated lattice pararneter and the rvns strain, Ehkl, was derived and found to fit the results acceptably well. From this and other relationships developed in the papev it was estimated that the equilibrium stacking-fault energy of Cu-30Zn was between 8.4 and 12.5 ergs per sq cm, in fuirly close agreement with the (corvected) value obtained by Howie and Swann (1961)43 using transmission electron microscopy. The theory of work hardening in the jorm developed and recently presented by Hirsch (1964)3 successfully described all the pvesent observations. In order to test certain aspects of the theories of work hardening, as developed by Mott,1 Hirsch,2,3 Seeger et el,4-7 and others (for review see Nabarro, Basinski, and Holt8), several recent investigations have been concerned with relating the dislocation density, p, with the shear stress, 7 (and strain, y), applied to the specimen. The results of these investigations have shown that the square root of the dislocation density appears to be linearly related to the applied shear (or flow) stress for fcc as well as bcc metals and alloys. Furthermore, the relationship appeared to apply not only to the deformation of poly-crystalline specimens, but also to stages I and I1 of the deformation of single crystals. An expression of the form has thus come into wide use. Here b is the Burgers vector for a total dislocation, G is the shear modulus, and 70 and q are constants. A review9 of available values of q shows it to have values (at room temperature) in general between 0.3 and 0.6. Forms of Eq. [1] can be deduced from, or predicted by, the current theories, and the various constants adjusted so that they are compatible with the experimentally found value of q . No unique relationship has yet been found between the dislocation density and the applied shear strain. There are several serious objections to the use of Eq. 11]. In the first place, it relates the shear stress to the density of the dislocations without regard to their arrangement, type, or distribution; the significance of the relation may therefore be justly questioned.5 In the second place, the values of the experimental quantities usually substituted into Eq. [11 are those of the applied shear stress and the total dislocation density measured after unloaditzg. The dislocation density value that should in fact be used is that for the mobile dislocations present in the specimen when under the applied load.* Finally, in cases where the values used for p, the dislocation density, are those obtained by electron microscopy, p is subject to considerable error,&apos; both systematic and random. The corrections to be applied are still controversial. Dislocation densities can also be measured by etch-pit and other techniques,&apos;&apos; each having their specific limitations. An objective of the present investigation has been to obtain information about the dislocation configyration and distribution by analyzing the changes in the position and shape of X-ray diffraction profiles as a function of deformation. The X-ray techniques employed, also open to criticism, have certain advantages, however. Thus, although the X-rays diffract only from the surface layers to an effective depth of about 20 p, the measurements can be made while the specimen is under load. The value of the dislocation density obtained by the X-ray method is also subject to errors, which are different from those of the electron microscope. Though a considerably larger volume of material is sampled by the X-rays, thereby reducing some of the statistical errors inherent in the electron microscope data, the information obtained is less detailed and is dependent on the method of analysis used to obtain a value for the dislocation density. Nevertheless, important observations can be made because the aforementioned advantages outweigh some of the limitations. In the present paper the X-ray method is briefly described and applied to a brass specimens deformed in tension. The results are then discussed in terms of some of the current concepts of work hardening. 1) EXPERIMENTAL PROCEDURE Details have already been extensively published elsewhere11-14 and therefore will only be dealt with briefly here. 1.1) Materials and Specimen Preparation. Commer-

Jan 1, 1968