Search Documents

By A. M. Skov, L. F. Elkins

First response to large-scale water flooding in the fractured very low permeability Spraberry sand has led to a new unique cyclic operation. Capacity water injection is used to restore reservoir pressure. This is followed by marly months production without water irzjection and the cycle repeated. Expansion of the oil, rock and water during pressure decline expels part of the fluids but capillary forces hold much of the injected water in the rock. At least with reservoir pressure restored and with partial water flood development, field performance has proved this cyclic operation is capable of producing oil from the nzatrix rock at least 50 per cent faster and with lower water percentage than is imbibition of water at stable reservoir pressure. INTRODUCTION The Spraberry Field of West Texas presents unusual problems for both primary production and water flooding. Extensive interconnected vertical fractures in the fractional-md sandstone permitted recovery of oil on 160-acre well spacing, but they made capillary end effects dominant. Primary recovery by solution gas drive is less than 10 per cent of oil in place. The concept of displacement of oil from the sand matrix by capillary irnbibition of water has led to field techniques which promise greatly increased oil recovery. Free exchange of laboratory research, reservoir information and results of field pilot tests among the various companies has been very important in development of this technology. Five units covering a total of 170,000 acres have been formed for water flooding, and 10 other areas covering an additional 175,500 acres are in various stages of unitization. Part of the Driver Unit reaching fillup first has demonstrated very unusual waterflood behavior and indicated numerous operating problems that will develop within and among the various units. SPRABERRY ROCK AND PRIMARY PERFORMANCE The Spraberry, discovered in February, 1949, is a 1,000-ft section of sandstones, shales and limestones with two main oil productive members: a 10-15 ft sand near the top and a 10-15 ft sand near the base. In part of the field some thinner intermediate sands are oil productive, and others are water bearing. All sands have permeabilities of 1 md or less and porosities of 8-15 per cent. Ordinary core analysis and electric and radiation logs are ineffective in differentiating between oil productive and nonprcductive sands. Sands capable of containing producible oil are best identified by mercury injection capillary pressure measurement and, in some cases, by core water saturation. About 3,500 wells have been drilled in the 500,000-acre trend. Vertical fractures were observed in practically all Spraberry cores. Continuity and interconnection of fractures were confirmed by pressure interference among wells during early development.' Major fractures trend northeast-southwest as indicated by oriented cores and confirmed by five fluid injection tests, by analysis of the pressure transients observed during development,''' and by three interference tests in the Driver Unit Water Flood reported herein. Fracture spac- ing probably averages inches to a few feet. Spraberry wells typically produced 100-400 BOPD initially after hydrauLic fracture treatments. By 1962 oil production had declined to an average of 12 bbl/well/day, near the economic Limits of operation. Reservoir pressure had declined from 2,300 psi initially in the Upper Spraberry and 2,500 psi in the Lower Spraberry to 500-1,000 psi. Partial closing of the fractures with declining reservoir pressure is believed to be the cause of such low oil production rates at these relatively high reservoir pressures. Cumulative recovery of 208 million bbl of oil is 80 to 90 per cent of that recoverable by primary means. Performance of the entire reservoir is summarized in Fig. 1. IMBIBITION WATER FLOODING By 1952 reservoir performance indicated low primary recoveries. Most engineers, expecting serious channeling of injected fluids through the fractures, held little hope for secondary recovery. With its extensive background of research on the fundamentals of fluid flow within reservoir rocks, Atlantic's Research and Development Division on short notice in 1952 conceived that displacement of oil by capillary imbibition of water into the rock might significantly increase Spraberry recovery. Laboratory data reported by Brownscombe and Dyes scaled to probable reservoir conditions showed potential waterflood recovery equal to or greater than primary recovery with a 10-15 year flood life.= A pilot test using three 40-acre injection wells, one central producing well and 18 surrounding observation wells demonstrated technical feasibility of the process. Injection of 1.5 million bbl of water from November 1952 to August 1955 proved water entered the rock and displaced oil

By E. P. Whittemore

Experience with the ASC multipoint gas lift system was obtained in Colonia zone of the West Montalvo field near Oxnard, Calif. The wells in this pool produce from depths varying from 10,500 to 12,000 ft. Oil gravity is generally 14 to 15' API with a few extremes of 12 and 20" API. Some salt water is produced which causes some very viscous emulsions. Viscosities at 150F (which is the approximate wellhead temperature) vary from 5,000 to 100,000 SSU. Most of the production is by gas lift, although a few wells are produced by rod and hydraulic pump. About half of the gas-lift wells are on continuous flow and the remainder are on intermittent lift using large, ported, pilot-operated valves for single-point transfer of gas from casing to tubing. Gas-liquid ratios vary from about 6 to 10 Mcf/bbl of gross fluid lifted. Wells are produced to a 450-psi trap system. The following remarks will be confined to intermittent lift only, since this is the type of lift which has been achieved with the ASC valve system. The maximum gross fluid which has been produced by single-point intermittent lift is about 350 B/D in 3-in. tubing and 200 B/D in 21/2-in. tubing with gas-liquid ratios of approximately 7 to 9 Mcf/bbl. Some design changes could reduce this ratio. The ASC multipoint system has provided production as high as 480 BOPD in 21/2-in. tubing with gas-liquid ratios just under 4 Mcf/bbl. To be able to apply the multipoint system, it is recommended that a detailed explanation be obtained concerning transition-point pressure and stabilizer setting—what its significance is to the string design, how it may work for or against the operation of the well, how it is related to tubing sensitivity and how it affects the unloading operation. The unloading operation may only be of academic interest in a technical paper, but to the production foreman, unloading and setting the valves in operation is a very real problem and should be understood in detail. One item touched lightly in the paper was the unloading valve. This valve controls the maximum pressure at which the well can be operated. When lifting heavy viscous fluids, it is most important to set this valve for the maximum possible realistic operating pressure at the surface. If the well lifts easily, it is simple to set the ASC valves at a lower operating pressure and the unloading valve will remain closed; but if the well happens to be heavier to lift than anticipated, it may be desirable to operate on the unloading valve itself and use all the energy obtainable at the bottom of the hole. In the Colonia pool very heavy wet-gas gradients are experienced due to the viscosity of the liquid and the dense mist which is left behind a slug of fluid. There are many combination strings of 3- and 21/2-in. tubing. This aggravates the wet-gas gradient problem and provides wet-gas gradients of about 50 to 70 psi/1,000. An advantage which multipoint lift has provided is increased slug efficiency through better maintenance of pressure under the slug and decreased fall back as the slug passes up the tubing. By using multipoint injection, wet-gas gradients have been reduced to about 30 psi/1,000. This has reduced bottom-hole operating pressure and given a production increase. The ASC valve is not a simple device. It's operation is difficult to understand, and it must be understood to be used efficiently in gas-lift design. Operating problems are difficult to diagnose—whether they be caused by the fluid lifted, valve malfunction, lift gas rate, or operating pressure. Calculations and reasoning are required to find out what is causing the problem. Inherent in the ASC valve is the inability to create large pressure differentials across a slug. Large differentials may be required to overcome the inertia of very viscous fluid as it is being accelerated in the bottom of the hole. This is tied back to the design of the unloading valve and is one reason for the importance of setting the unloading valve for the highest possible operating pressure. ~u; to the narrow spread the ASC valves provide, it is impossible to cycle slower than about 24 cycles/day on choke control. If small production of 150 BOPD and less is expected, a surface time-cycle controller will be required if the most economical operation is to be achieved. To achieve a satisfactory operation, the operator must keep a record of any changes made in the operating pressure of the ASC valves. Anything which may cause changes in casing pressure in excess of the stabilizer setting will change the valve operating pressure, and if this is not noted from daily inspection of the well casing-tubing pressure recorder charts, the operator will lose control of the well. Significant results can be achieved using ASC valves; however, considerable knowledge is required to design with them, and attention to detail is required for satisfactory field operation.

Jan 1, 1965

By N. Brown, R. Kossowsky

Plain carbon steels with 0.48 and 0.95 pct C were quenched and tempered at 705°C to produce carbide dispersions with spacings on the order of 1 p. The morphology of the structure consisted of a carbide-dislocation network. The strengthening due to the dispersion was found to vary linearly with M-½ where M is the mean free-ferrite path determined by the entire network. No preyield microstrain preceded the upper yield point. After prestraining, the lowest stress at which dislocation movement could be detected was 104 psi; this frictional stress was independent of the dispersion and prestrains up to 6.5 pct. The Cottrell-Petch equation for grain-size strengthening was used to discuss the dispersion strengthening in this investigation. The results support an impurity mechanism for the upper yield point rather than one based on the Johns ton- Gilman theory. IT was pointed out by Gensamerl that the mean free path in the matrix is the important variable which controls the degree of dispersion strengthening. Gensamer's data on steels showed a linear relationship between the yield point and the logarithm of the mean free-ferrite path. The first theory was by Orowan,2 who suggested the mechanism of dislocations bowing between particles, with the resulting relationship that where a is the yield point, P is the distance between particles, and G is the shear modulus. The Orowan equation applies to that range of dispersion where P is large compared to the particle size and the particles are not coherent, so that the matrix is essentially free of internal stresses. As was pointed out by Orowan, there are different degrees of dispersion which, in turn, will influence the strength-controlling mechanism. However, in this investigation, we wish to confine ourselves to the region of coarse dispersion, where the Orowan mechanism should, intuitively, be applicable. It was soon evident that the data, which existed at about the time that the Orowan theory was proposed, did not agree with the Orowan equation in that the actual strengthening was always greater than the theoretical predictions. Thus, Fisher, Hart, and pry3 modified the Orowan theory by suggesting that the Orowan process took place in the microstrain region preceding macroscopic yielding and the subsequent, rapid work hardening in the form of residual dislocation loops around the particles largely determined the observed macroscopic yield point. The F-H-P theory stated that the increment of strengthening due to the work-hardening mechanism was proportional to f3/2 where f is the volume fraction of the precipitate. F-H-P used data by Shaw, Shepard, Starr, and Dorn4 on A1 3-5 pct Cu to support their theory. Roberts, Carruthers, and Averbach5 were the first to make a microstrain study of dispersion strengthening, and they found that for steel the Gensamer relationship was obeyed. Hayman and Nutting6 suggested that in the case of tempered steel 1) the ferrite grain boundary was the primary obstacle and 2) the carbide particles simply formed part of the grain boundary obstacles. They found that the strength varied as G"" where G is the ferrite grain size. Turkalo and LOW' determined the structure of quenched and tempered plain carbon steel using a replica technique; they concluded that the carbide particles did not necessarily lie in the ferrite grain boundaries. When they defined the mean free-ferrite path as being determined by both particles and the ferrite path boundaries, their data obeyed the Gensamer relationship. Meiklejohn and skoda8 showed that the strengthening from iron particles in mercury was a function of the particle size and the distance between particles. Dew-Hughes9 explained the Meiklejohn and Skoda results by the following theory: 1) grown-in dislocations which surrounded the particles were produced by the thermal stresses during the time the material was cooled to the testing temperature, and 2) the observed strengthening was associated with the cutting of the grown-in dislocations by the glide dislocations. Ansell and Lenel10 proposed a theory in which the glide dislocations pile-up or surround the particle until the number of dislocations in the pile-up is sufficient to yield or fracture the particle. The resulting theory says that the yield point varies as p-1/2, where P is the distance between particles. The Ansell-Lenel theory is almost identical to the

Jan 1, 1965

By J. Chipman, G. G. Hatch

T. ROSENQVIST*—It is a pleasure to see the excellent way in which the experimental part of this work has been handled. There seems to be little doubt that the distribution data obtained corresponds most closely to thermodynamic equilibrium under the prevailing reducing conditions, namely equilibrium with graphite and one atmosphere CO pressure. The desulphurization curves in Fig 10 show the same general feature as the curves given by Holbrook and Joseph, but the distribution ratios are from 20 to 40 times greater—undoubtedly due to a closer approach to true equilibrium. In the theoretical discussion, the authors calculate a theoretical distribution (S) ration -jg-. which they find to be about 50 times greater than the experimental. The deviation is so great that the basis for their calculation needs a more thorough examination. The authors base their thermodynamic calculation on free energy expressions where diluted solutions of FeS and CaS are used as standard states. (The activity coefficient in diluted solutions is taken to equal unity.) Such a standard state will change when the nature of the solvent is changed. Taking the free energy of the reaction [FeS] ? (FeS), Eq 2, which is derived from the distribution of sulphur between an iron and a FeO-melt, it is very unlikely that the free energy of this reaction will be the same for a distribution between pig iron and a calcium silicate slag. Therefore a more fundamental basis for the thermodyuamic calculations seems needed, where all thermodynamic equations are referred to unambiguously defined standard states. The most natural standard states for CaO and CaS are the pure solid substances at the same temperature. As standard state for sulphur in iron, pure liquid FeS can be used. This rules out Eq 2 [FeS] ;=s (FeS) because ?F° = 0. The standard equation will then be: FeS, + CaO6 + Cgraph ?Fei + CaS8 + CO. vFo1773 = 25,000 cal It would be more universal and also simpler to refer the escaping tendency of sulphur in liquid iron to the corresponding H2S/H2 ratio which can readily be determined experimentally. As standard state a gas mixture H2S/H2 = 1/1 can be used. (This corresponds at the temperature of liquid iron closely to one atmosphere S2 vapor.) Thus the standard equation for the sulphur reaction can be formulated as follows: H2S0 + CaO3 + Cgraph ?H2o + CaS8 + COg The standard free energy of this reaction has been calculated from the best available data to AF°m3 = —35,000 cal. This gives for the equilibrium constant at 1500°C Now, the solubility of CaS in blast furnace slags has been determined by McCafferey and Oesterle* and corresponds at 1500°C to about 10 pet S (varying somewhat with the composition of the slag.) If the activity of CaS is assumed linear between 0-10 pet as curve 1, (see Fig 11), then acaO = 0.1 (S); (S) being wt. pet sulphur in the slag. For a diluted solution of sulphur in an iron melt saturated with carbon, the ratio H2S/H2 is, according to Kitchener, Bockris and Liberman,f about 0.01 [S], [S] being wt. pet sulphur in iron. Substituting these values in the expression for Kp we find The value 2.103 is only 4 times greater than the experimental coefficient found by Hatch and Chipman, but the value is very sensitive to a small error in AF°. A better agreement with the experimental distribution coefficient can be obtained if one assumes the activity of CaS to run like curve 2 (Fig 11). This (S) will give a lower theoretical W, value, a value which varies with (S) exactly as Hatch and Chipman learned. Such a shape of the activity curve, which corresponds to a positive deviation from Raoult's law, is actually to be expected from the fact that liquid silicate and sulphide phases usually show incomplete miscibility. A closer agreement between experimental and theoretical data can not be expected before we have more complete data for the individual activities of CaS and CaO in the slag. The activities acaS and Ocao referred to the solid phases as standard states, are exact defined quantities contrary to the somewhat undefined expression "free lime," and they are independent of any theory for the constitution of liquid slag. J. CHIPMAN (authors' reply)—The authors wish to thank Mr. Rosenqvist for his very interesting and useful thermodynamic addition. Curve 2 of his figure offers the needed basis for explaining the increase in the ratio (S)/[S] with increasing sulphur content. Attention is called to an error in the printed paper: Fig 2 and 3 are reversed. M. TENENBAUM*—In the figures showing the relationship between excess base and sulphur distribution (Fig 6, 7 and 9) the slope of the curve tapers off in the negative basicity range. Somewhat the same thing is observed with open hearth slags. In that case, the fact that some sulphur distribution between slag and metal is obtained with negative basicity is interpreted as indicating some dissociation of the lime silicate compounds whose existence in oxidizing basic slags has been used to explain various observed phenomena with regard to other slag-metal reactions. In the case of the blast furnace slags, the reduced slope of the sulphur distribution curve with decreasing excess base is attributed to the amphoteric effect of alumina. Has the possibility of other explanations been investigated ?

Jan 1, 1950

By R. T. O’Brien, J. M. W. Mackenzie

A microelectrophoresis technique has been used to measure the zeta potential of quartz over a range of pH and Ni (11) and Co (Ilj concentrations. Results have been discussed in terms of adsorption of Ni (11) and Co (11) cations and hydroxide precipitates. Possible relationships between the experimental results and the formation of lateritic nickel deposits have been discussed. The adsorption of metallic cations to the surface of silicate minerals is of significance in many industrial and natural processes. In an earlier publication,' the adsorption of Fe (111) to the quartz surface, a phenomenon of importance in flotation, was studied qualitatively using microelectrophoresis techniques. This paper reports the extension of this work to an investigation of the adsorption from aqueous solution of Co (11) and Ni (11) to the quartz surface. The adsorption of these metals was of interest for two reasons; firstly, the importance of such an adsorption process in the formation of nickel deposits by the lateritization of nickeliferous rocks, and secondly, the comparison of electrophoresis data for these metals, whose hydroxides precipitate in the pH range 7-8, with similar data for Fe (111) where the hydroxide first precipitates at pH 2.8. The development of laterites is essentially a near-surface geological process involving vertical and, in part, horizontal redistribution of elements derived from rock-forming minerals. This redistribution of elements leads to the formation of layers within the lateritic profile which are enriched in one or more of these elements and, depending on the nature of the original rocks, continued lateritization may give rise to iron ores, bauxites or nickeliferous laterites. The mechanisms discussed in this paper deal with the last mentioned type of deposit although the considered factors are applicable to laterites in general. Nickeliferous laterites are derived from basic and ultrabasic rocks containing ferro-magnesian silicates. These rocks may be partly or wholly converted to serpentinites. Besides their high Mg, Si and Fe contents, they also contain small amounts of Mn, Al, Cr, Ni, Co, Cu and Zn. The nickel content is usually near to 0.2-0.3%, but for economic use this must be increased during lateritization to over 1% and preferably over 2%. The zone of nickel enrichment is usually at some depth within the lateritic profile. Unpublished work by Mr. O'Brien on nickel-bearing laterites in eastern Australia indicated four visually different types of material which were separated from crushed samples under a stereo-microscope. Although chemical analyses indicated that all four types of fragments contained 2-4% nickel and smaller amounts of cobalt, X-ray diffraction and optical studies revealed only quartz, hematite and chromite as well as, in one of the types, a serpentine mineral. No distinct, nickeliferous minerals were detected. Furthermore, it was possible to extract some 60% of the nickel content of the laterites with cold 0.5N hydrochloric acid. It was therefore postulated that much of the contained nickel was present as amorphous, adsorbed material. In considering this fact, as well as the problem of the actual method of transfer and fixation of elements within the lateritic profile, it was further postulated that the transfer of these elements probably took place partly as solutions and partly as colloids and that the fixation of these was caused by adsorption and flocculation. The existence of nickel in solution in water draining from serpentinites has been confirmed by Smurov.2 Although we have no evidence for the transportation of nickel in the colloidal state, it is well accepted that colloids are important in the formation of laterites. Previous work by Mr. Mackenzie' has already indicated that iron may be adsorbed on quartz under conditions which could be expected in a lateritic profile, but no information was available for nickel or cobalt. Although adsorption possibly also takes place on minerals other than quartz, the latter is significant because silica is an important constituent of the silicate parent rocks. During lateritization, it is released to form free quartz and it is likely that it is initially extremely fine-grained. This would provide abundant opportunities for adsorption and it was de-

Jan 1, 1970

By Edwin Ludlow

EDWIN LUDLOW, the 41st President of the A. I. M. E., died in Muskogee, Okla., on Feb. 10, 1924, after a brief illness of influenza followed by pneumonia. He was born in Oakdale, Long Island, N. Y., March 12, 1858, a son of William Handy and Louise (Nicoll) Ludlow, attended Flushing (L. I.) Institute 1868-75: and Columbia School of Mines (N. Y.) where he graduated with the degree of Engineer of Mines with the Class of 1879. After graduation his first employment was as assistant engineer in river and harbor work on the Delaware River near Philadelphia. In 1881 he went to Mexico as one of the engineers on the Mexican Central Railroad, then building from Laredo, Texas, to Mexico City. The road being in financial difficulties he returned to the United, [states, and shortly thereafter was made superintendent of the Union Coal Co.'s collieries located in the western middle anthracite field, between Shamokin and Mt. Carmel. Ludlow and Arthur H. Storrs, then superintendent of the Neilson Shaft Colliery, in Shamokin, were known throughout that section as the baby superintendents, both under 25 years of age. The appointments of such young men were at that time unique and set a record for youthful assumption of re-

Jan 1, 1924

By I. R. Kramer, H. Shen, S. E. Podlaseck

The tensile and creep properties of aluminum in vacuum have been investigated. It was found that the general effect of a vacuum environment was to reduce the rate of work hardening. Results obtained from creep tests showed that lowering the test pressure from 2 x 10-4 to 10-7 torr produced a decrease in the activation energy as much as 500 cal per mole. An attempt is made to explain these effects in terms of how the surface-stress field of a specimen may be affected by a vacuum environment during plastic deformation. In a previous paper,' the results were reported of some of our early work on the effect of vacuum environment on the stress-strain curve of aluminum single crystals. This effort has been extended to the studies of the tensile and creep properties in vacuum as a function of various metallurgical parameters. Some of the recent surface-effect studies2'3 have revealed that a region of high dislocation density, the so-called "debris" layer, is formed near the surface of the specimen as a result of plastic deformation. This layer acts as a surface barrier to oppose dislocation movement. The strength of this barrier depends on the surface condition such as oxidation or surface removal. Experimental results obtained from surface-removal work2, 3 indicate that such a surface barrier, which may be characterized by a stress field, affects the applied stress and the rate of work hardening. In the case of aluminum, this stress field was found to be directly proportional to the strain and the strain rate; however, the slope of this curve is independent of orientation of the crystal and may be altered by using different surface treatment. Since the escape of dislocations may be retarded by the presence of an oxide on the surface of a specimen, it is expected that a change in the rate of oxidation in vacuum will affect the process of dislocation accumulation in the debris layer. Consequently, it also affects the plastic behavior of a metal. This paper reports the changes in some of the creep and tensile properties of aluminum in vacuum and discussions of the observed effects in terms of the concept of the "debris" layer. EXPERIMENTAL PROCEDURE Tensile Tests. A sketch of the tensile apparatus is given in Fig. 1. This apparatus was contained in a bell jar (14 in. diam by 24 in. high) connected to a 10-in. vacuum system. The load was applied to the specimen by means of a gear train which was driven by a magnetic clutch located outside the vacuum chamber. The specimen, held by a pair of square shoulder grips, was attached to the load cell at the top and the drive gear at the bottom. A displacement transducer was placed between the two grips as shown in the figure to measure the elongation. Signals of elongation and load were amplified and recorded on an X-Y recorder. The system was capable of detecting loads as small as 0.025 lb and displacements of 0.0002 in. Shoulder-grip specimens of aluminum single crystals, having a nominal square cross section of 1/8 by 1/8 in. and a 3-1/2-in, gage length, were grown by the Bridgeman techniques. The original purity was 99.997 pet. The orientations of the crystals investigated are shown in Fig. 4(a). The crystals were annealed at 600°C for 2-1/2 hr, electropolished, and placed in the vacuum test chamber without any delay. All the crystals were deformed at a strain rate of 4 x 10-5 sec-1 at 24o ± 3°C. A study was made to find whether a chemically passive surface film would give the same effect as a vacuum environment. Specimens of aluminum 1100 (0.187 in. diam with a grain size of 0.1 mm)

Jan 1, 1965

By AIME AIME

NO FEATURE of the annual meeting is considered more important at Institute headquarters than the assembly of delegates from the various local sections and divisions. There the president of the Institute and other officials may learn at first hand what the members are thinking and doing in every part of the country, and the delegates, in turn, may find that head- quarters is not a group of more or less cold-blooded New Yorkers whose primary function is to send out annual bills for $15. This year, the section and division delegates required three sessions to thresh out the matters of common interest: Monday morning and afternoon and Thursday afternoon. They were also guests of the Institute at the Directors' dinner on Tuesday night, and at the Directors' meeting afterward.

Jan 1, 1932

By M. T. Simnad, G. Derge, I. George

Measurements of current efficiency on iron-silicate slags in iron crucibles showed that conduction is about 10 pct ionic in slags with less than 10 pct silica and about 90 pct ionic in slags with more than 34 pct silica, increasing linearly in the intermediate range. The balance of the conduction is electronic in character. Silicate ions are discharged at the anode with the evolution of gaseous oxygen. Transport experiments show that the ionic current is carried almost entirely by ferrous ions, which may be assigned a transport number of one. THERE has been increased evidence in recent years that the constitution of liquid-oxide systems (slags) is ionic.1-3 The principal studies designed to establish the structure of liquid slags have been by electrochemical methods', " and conductivity measurements1,6,7 which also have indicated the presence of semiconduction in several silicate systems1,4-0 and in pure iron oxide.' It is well known that many slag-forming metallic oxides have an ionic lattice type in the solid state, and their properties are determined to a large extent by the lattice defects and ion sizes. As Richardson8 as pointed out, the detailed models of liquid slags cannot be found on thermodynamic data only but "must rest on a proper foundation of compatible structural and thermodynamic knowledge, combined by statistical mechanics." A careful thermodynamic study of the iron-silicate slags has been carried out by Schuhmann with Ensio9 and with Michal.10 They obtained experimental data relating equilibrium CO2: CO ratios to slag composition and made thermodynamic calculations of the activities of FeO and SiO, and of the partial molal heats of solution of FeO and SiO2 in the slags. It was found that the activity-composition relationships deviate considerably from those to be expected from an ideal binary solution of FeO and SiO2. However, the partial molal heat of solution of FeO into the slags was estimated to be zero. Their experimental results were correlated with the constitution diagram for FeO-SiO2 of Bowen and Schairer,11 with the results of Darken and Gurry" on the Fe-O system, and with the work of Darken"' on the Fe-Si-O system. All these studies were found to be consistent with one another. The variation of the mechanism of conduction with composition in the liquid iron-oxide-silica system in the range from pure iron oxide to silica saturation (42 pct SiO2) in iron crucibles was reported in a preliminary note." The current efficiency, or conformance to Faraday's law, showed some ionic conductance at all compositions, the proportion increasing with the concentration of silica. The current-efficiency experiments since have been extended. Furthermore, transport-number measurements have been completed in silica-saturated iron silicates to determine the nature of the conducting ions. Experimental Current Efficiency in Liquid Iron Oxide and Iron Silicates using Iron Anodes: This study was carried out by passing direct current through slags in the range from pure iron oxide to iron oxide saturated with silica (42 pct silica), using pure iron rods as anodes and the iron container as the cathode. A copper coulometer was included in the circuit to indicate the quantity of current passed during electrolysis. Assuming that the cation involved is Fe-+, the theoretical quantity of iron lost from the anode according to Faraday's law may be calculated and when compared with the actual loss observed, gives an indication of the extent to which Faraday's law has been obeyed. It also gives an indication of the presence and extent of ionic conduction in the melt. Preparation of the Slags: About 100 g of chemically pure Fe,O, powder is placed in an iron pot which is heated by induction until the contents liquefy. In this way, FeO is produced according to the reaction Fe2O3 + Fe = 3 FeO. More Fe2O3 or SiO, powder is added and, when a sufficient quantity of molten slag is obtained, the induction unit is turned off, the pot withdrawn, and the molten slag poured on to an iron plate. Homogenization and Electrolysis of the Slag: Apparatus—After considerable development, the setup illustrated in Fig. 1 proved to be quite satisfactory. A is an Armco iron cylinder, 1 in. ID and 1/8 in. wall, consisting of three sections placed one on top of the other. The bottom section is a pot about 5 in. long with a small hole drilled in its bottom to allow withdrawal of gases during evacuation of the apparatus. The middle section is 6 in. long and consists of a pot which serves as the slag container, while the top section is a hollow-cylinder continuation of the slag-container pot. The height of this latter section is about 5 in., giving an overall length of approximately 16 in. The iron cylinder is constructed in this way for ease of fabrication, the individual sections becoming welded together after the

Jan 1, 1955

By R. D. Lord

The search for the best practical means of storing sulfide bearing tailings, where there is no residual excess of carbonate material is discussed in this paper• Usually the sulfide content decomposes, with the aid of bacterial action, and the resulting sulfuric acid escapes, along with any heavy-metal solutes, through embankments that are usually porous to some degree• The problem is typified in the tailings of the uranium operations of Elliot Lake, Ont., where mining started some 20 years ago• The approach to tailings disposal paralleled the practice for other hydrometallurgical plants treating gold and base-metal ores• Impoundment areas were designed to retain solids, and a clear and neutral overflow was considered satisfactory practice• Now experience has shown that these areas, some of which have been idle for over a dozen years, release acids in seepage and overflows to an unacceptable degree• To protect natural water courses, neutralizing plants are operated wherever required• Lime slurry is fed continuously into the tailings outflows in a quantity sufficient to raise the pH to 8•5 and precipitate heavy metals that may be in solution• The objection to this procedure is that the plants will require servicing indefinitely, unless a better remedy is found• The problem differs only slightly from that common to base-metal concentrators in that here the ore has been leached with sulfuric acid for the recovery of uranium• Any native content of calcareous material has been digested, and only that added for final neutralization is available to maintain a pH unfavorable to bacterial activity• Chemical oxidation slowly lowers the pH and when this reaches a level of 4•5 or less, bacteria become active and greatly accelerate the formation of acid. The bacterial process is probably at least ten times as fast as the chemical oxidation• Location and Processing The operations referred to, uranium and one copper mine, are located at approximately 46°N and 82°W longitude• This is typical Canadian Shield country, a land of lakes, deeply glaciated and rocky, with sparse soil which supports mixed forest cover• Drainage is to Lake Huron, 25 miles to the south• Average temperature is 45°F, ranging from -40° to +95°F• Annual precipitation is 38 in•, about half of which is snow• The ore is Precambrian, quartz-pebble conglomerate, with mineralization in the matrix• From 5 to 10% pyrite is present• All known means of pre-concentration have been tested, but a bulk sulfuric acid leach has proved the most efficient. Tailings have from the outset been neutralized before release• Current practice is to add ground limestone to bring the pH to 4•5, and then lime to raise the value to 10•5• Environmental regulations have recently been increased and the foregoing meets the new standards• Separate measures are taken to precipitate radium• Remedial Measures Since the outstanding environmental problem is the oxidation of pyrite by bacterial action, the solution is to contain the products, or arrest the process• Given the ambient temperature, favorable half of the time, four items are essential to the activity• 1) Pyrite• 2) Moisture pH < 4•5. 3) Oxygen• 4) Bacteria• Removing any one of these out of the range of tolerance will bring the reactions under control• A variety of proposals considered, and a number tested for the arrest of the process, are: (a) render embankments impermeable, (b) provide an impermeable cover, (c) cover with an oxygen absorbing layer, (d) provide a vegetative cover, (e) flood the site, (f) remove pyrite from current tailings, (g) add excess limestone to current tailings, (h) poison the bacteria• Bank Seal-On existing impoundment areas, where the embankments are several thousand yards in length, it is believed that any program of injecting sealants can have small chance of success• However, a moisture barrier is an indicated specification for future construction, and this can be highly expensive• Surface Seal-Depending on the configuration of the deposit, the downward travel of water should be prevented, and oxygen excluded• Burying a plastic membrane just below the surface has been considered, as has the application of a liquid sealant that would penetrate the surface. The objection to these remedies is the excessive cost of dealing with large areas and the expectation of only temporary benefit as a result• Frost penetration is over 4 ft, and frost action breaks up asphalt paving and all but heavy concrete in a few years• Organic Layer-An oxygen-absorbing layer, such as bark fines from paper mills has been proposed as a surface treatment• Cultivated into the tailings such material might be expected to arrest subsurface oxidation for some years• Estimates are 100 tons per acre of bark fines, or 35 tons per acre of sawdust, and these enormous quantities do not so far give assurance of providing a long-term remedy• Vegatative Cover-Several obvious benefits would result from a good growth of grass or other vegetation on abandoned tailings• While restoring the natural green of the tract the growth would prevent wind-blown dust and reduce erosion• Subsurface oxidation should be reduced, as well as the upward movement of ground moisture as occurs in dry weather. To this end, considerable research and field testing has been carried out to arrive at a formula - a prescription which will provide a self-sustaining growth on the tailings surface, or at least one that would survive with reasonable maintenance attention. Many test plots have been run with different combinations of surface treatment and seed mixtures. Generally, by addition and close cultivation of limestone, lime, and fertilizers, technical success has been demonstrated• Plants with a high tolerance for acid soil seem the more hardy, and a pH above 3 is indicated so that nutrients can be absorbed• Recommendations are for 12 to 15 tons of

Jan 1, 1977

By George H. Anderson

A CHAPTER of appealing interest was added to the industrial history of the Southwest early in June, when the War Production Board gave final approval to the erection of a blast furnace, a battery of coke ovens, an ore-beneficiation plant, and other facilities for the production of pig iron in northeastern Texas, just north of the East Texas oil field. For many years the people of Texas and adjoining states have cherished the ambition and desire that eventually an iron and steel industry drawing upon local mineral resources would be established to serve Southwestern markets. The existence in this vicinity of valuable deposits of iron ore, limestone, and coking coal has been known in a general way for many years, and efforts have been made from time to time to use them in the production of iron. The present development promises to bring to realization the dreams of the men who have visualized what the establishment of this basic industry would mean to the region.

Jan 1, 1942

By Robert Schorr

A Discussion of the Paper by Robert Schorr, read at the Atlantic City meeting, February, 1904. (Washington Meeting, May, 1905.) E. T. DUMBLE, Houston, Texas (communication to the Secretary*) :-In addition to the list of publications mentioned by Mr. Schorr and those by Prof. Hofman, I call attention to the following references : Studi sulle Lignite, by Capacci. Turin (1890). (An excellent work.) Report of Brown Coal Industry in Germany. J. Cosmo Newberry. Department of Mines, Victoria (1892). Second Report of the Royal Commission. on Coal Supply. Vol. II. London (1904). Peat Fuel: Its Manufacture and Use. Report of the Bureau of Mines of Ontario, 1903. Mr. Schorr says : " Brown coal and peat are briquetted as a rule without binder," but this statement is entirely true only so far as raw peat is concerned, and it is but partly true of brown coal. With regard to raw peat, briquetting without bond is carried on successfully both in Europe and America, and the development of the industry in Canada is fully described in the Bureau of Mines report for 1903, mentioned above. While there is still room for improvement in the efficiency of some of the arrangements for drying the peat previous to briquetting, a very satisfactory fuel is made at a price which enables it to compete with coal. During the late strike in the anthracite regions of Pennsylvania, the manufacture of peat: briquettes received a considerable impetus, and possibly the attention directed to it on this account may result in a. considerable increase in the output. In Canada. the peat when it is first excavated from the ground

Mar 1, 1905

By A. K. Mukherjee, John E. Dorn

The effects of strain rate and temperature on the critical resolved shear stress for (321)[111] slip were determined for the silver-rich CsCl type of intermetallic compound AgMg. The flow stress increased only slightly as the test temperature was first decreased below room temperature; a rapid increase in the flow stress was obtained with yet further decrease in temperature from about 250&apos; to 4OK. The effect of both the temperature and strain rate on the flow stress over the low-temperature range could be rationalized satisfactorily in terms of the Peiwls mechanism when the deformation was controlled by rate of nucleation of pairs of kinks. IN spite of the well-documented interest of metallurgists and engineers concerning the mechanical behavior of intermediate phases and intermetallic compounds, very little definitive information is available on this important subject. As recently summarized by westbrook,1 only limited and modest progress has been made thus far in elucidating the details of the mechanism of plastic deformation for the intermetallic compounds; the available information largely concerns phenom-enological descriptions of empirical observations and experimental facts, principally with reference to poly crystalline aggregates. The present report on the elucidation of the rate-controlling mechanism for slip in the bcc structure of AgMg is part of the comprehensive program of a systematic investigation on the mechanical behavior of intermetallic compounds. The intermetallic compound AgMg has a CsCl type of lattice structureZ and is completely ordered up to its melting point of 820c3 This material was selected for our present investigation because of its simple crystal structure, moderate and congruent melting point, ordered structure persisting up to the melting point, and some solubilities of the constituent elements, which could be expected to help in the growing of single-crystal specimens. Whereas previous investigations on the properties of AgMg include hardness,*"6 slip systems,7 tensile flow stress of polycrystalline specimens,&apos; and electrical resistivity,4 the current investigation will be directed principally at elucidating the rate-controlling dislocation mechanism responsible for slip in single crystals at low temperatures. It will be shown that the strain rate is consistent with a model involving the rate of nucleation of pairs of kinks by the Peierls mechanism for plastic deformation. EXPERIMENTAL TECHNIQUES Single-crystal specimens of the AgMg intermetallic compound were prepared and tested as follows: 1) A master alloy ingot of AgMg was produced by melting and chill casting the high-purity silver (99.995 wt pct) and high-purity magnesium (99.997 wt pct) in an induction furnace under a helium atmosphere. 2) Sections of the above-mentioned ingot were placed in a graphite mold containing a spherical cavity in which a single-crystal sphere of 1 in. diam was grown under helium by the Bridgman technique. 3) The operative slip systems were investigated at room temperature on a singlecrystal of AgMg, from measurements of the angles made by the slip traces on the two surfaces of the specimen, which were at 90 deg to each other. The investigation confirmed that the AgMg compound undergoes slip primarily in the (321) plane and in the [Ill] direction, but a small amount of secondary slip was also noticed in the (112) (111) system. No slip was observed in the (110) planes. 4) The single-crystal sphere, mentioned earlier, was oriented in a graphite mold containing a cylindrical cavity of 3/8 in. diam above the spherical receptable to give the angle xo = 45 deg between the axis of the cylindrical bar and the normal to the slip plane (321), and the angle AO = 45 deg between the slip direction [Ill] and the axis of the bar. Oriented single-crystal bar seeds were produced by melting, under a helium atmosphere, a polycrystalline bar in the cylindrical cavity above the oriented spherical seed and by growing an oriented single-crystal bar from the seed. 5) Finally, oriented single-crystal specimens were grown from these cylindrical seeds. 6) The cylindrical specimens were machined in a High-Tension Spark Cutting unit to give a 2-in. gage length. The spark-machined gage section was elec-tropolished in a bath containing 200 ml of H3PO4,

Jan 1, 1964

By Ralph Hultgren, Prodyot Roy

Manganese vapor pressures from 1250° to 1500°K were measured by conventional Knudsen and torsion-effusion methods in twelve Fe-Mn alloys with compositions from 9 to 80 at. pct Mn. The Knudsen re-sults agveed approximately with previous measurements found in the literature which indicated the solutions were nearly ideal. However, except for the higher manganese compositions, the initial torsion readings indicated much (up to 50 pct) higher vapor presszcres than the Knudsen method. These high readings decreased steadily with time. The results are interpreted as due to depletion of surface concentration of manganese during evaporation. Thus the initial torsion readings are the most nearly correct and Knudsen methods on alloys are to be regarded with suspicion unless it can be demonstrated that diffusion rates are rapid enough to replenish surface concentrations depleted by evaporation. For the lowest manganese contents and highest temperatures, depletion causes initial torsion readings to be too low. FEW thermodynamic data are available for alloys of the high-melting transition metals due primarily to experimental difficulties at the high temperatures involved. Measurement of vapor pressure is one of the most promising techniques to be applied to this problem. From the vapor pressure of a component of an alloy phase, its activity or its partial molar Gibbs energy can be directly calculated. From measurements over a sufficient range of temperatures and compositions the partial and integral Gibbs energies, enthalpies, and entropies may be determined through Gibbs-Duhem integration. For solid phases of variable composition, which commonly are found in alloys, measured vapor pressures are low because of depletion of the surface concentration of the more volatile component as it is selectively vaporized. Diffusion from the interior tends to restore the depleted concentration. The seriousness of the effect depends on the relative rates of diffusion and vaporization. Although depletion has been recognized as a factor,&apos; direct measurements of its rate are lacking and quantitative estimates of its effect on measurements are uncertain. In the present work the vapor pressures above a series of Fe-Mn alloys have been measured by the torsion-effusion method. This method permits a measurement of the vapor pressure of manganese as soon as the sample comes to temperature and continuously throughout the run. The rate of decline of the apparent vapor pressure measures the rate of depletion and the torsion reading at zero time should be correct. At high manganese concentrations (70 and 80 at. pct Mn), the torsion reading remained nearly constant; surface depletion was negligible. There was a slow drop in measured pressure due to bulk loss of manganese from the sample. However, for lower manganese contents, especially at high temperatures, the depletion effect was considerable and the apparent vapor pressure decreased steadily with time. For these alloys the Knudsen method should give pressures which are too low. The measurement of pressure in the Knudsen method cannot be made until enough manganese has been vaporized to be weighable. The Knudsen result is therefore an integrated average between the initial and final vapor pressures. To verify this, conventional Knudsen measurements were also made with results in approximate agreement with previously published Knudsen measurements for these alloys. As expected, for the lower manganese contents the initial torsion readings of pressure were as much as 50 pct higher than the Knudsen. THE APPARATUS The apparatus, shown in Fig. 1, is capable of operating to temperatures up to 2000°K. A vacuum of 5 x 10"6 mm Hg can be maintained. Temperatures were measured to +3° by a W-Re thermocouple placed in the dummy cell, N. The torsion cell consisted of two alumina crucibles with holes in their covers. They were placed in the molybdenum holder shown suspended from the torsion wire. Rectangular torsion wires (1 by 4 mm) were found to have superior sensitivity and less residual distortion than circular (2-mm-diameter) wires. The precision of angular measurement was found to be *0.025 deg; the variation is no doubt due to temperature fluctuation and vibration. For the Knudsen experiments the alumina cell was set on the support, N. SAMPLE PREPARATION 800-g samples were prepared by melting together electrolytic iron and electrolytic manganese and pouring the melt into a water-cooled copper mold. Melting and pouring were done under a helium at-

Jan 1, 1965

By A. J. Griest, P. D. Frost, H. A. Robinson

The flow characteristics and uniform elongation of alpha-beta titanium alloys in the solution-treated condition were shown to be markedly affected by the solution temperature. Two classes of alpha-beta alloys were distinguished, based on the effect of solution temperature on the uniform elongation. Martensitic alpha-beta alloys, which are relatively weakly beta-stabilized, showed decreasing values of uniform elongation as the solution temperature was initially increased. However, after solution-treatment at still higher temperatures in the alpha-beta field, the uniform elongation of these alloys was again high, and often attained its maximum value. Nonmartensitic alpha-beta alloys, which are more heavily beta-stabilized, showed a continuous decrease of uniform elongation with increasing solution temperature. The behavior was rationalized in terms of the alpha-beta ratio and the alloy content of the beta existing at the solution temperature. The data indicate that in commercial practice close temperature control may be required to get maximum uniform elongotion, and hence, maximum potential formability, in solution-treated sheet. Bend-test data also were obtained for the solution-treated conditions. A MOST important objective of current titanium research is the development of age-hardenable alloys with superior formability in the solution -treated condition. Alpha-beta titanium alloys have been shown to be amenable to high-strength aging treatments after solution-treatment in the alpha-beta field.&apos; However, heat-treatment data on the properties of solution-treated sheet, such as uniform elongation, minimum bend radius, and flow properties, which have a bearing on the potential formability, have not been widely available. This paper presents only the most significant results of a research program conducted at Battelle for the Air Force in an effort to develop sheet alloys that can be formed readily as solution-treated and subsequently aged to very high strengths. Data for 10 compositions representative of the more than 25 alloys studied in this program are presented. A primary objective of the paper is to demonstrate the pronounced dependence of the flow characteristics and uniform elongation on solution-treatment temperature. This effect is believed to be vitally important in the commercial heat-treatment of age-hardenable titanium sheet alloys. Experimental Procedures Melting and Fabrication—The nominal and actual compositions, beta transi temperatures, and rolling temperatures of 10 of the 30 alloys studied are presented in Table I. Stock :€or two of the alloys, E (Ti- 8Mn) and J (Ti-6A1-4V) was obtained from commercial heats. The remaining heats, except D and I, were double melted as 10-lb heats in a consumable-electrode furnace. Melting stock was 120 Brine11 hardness sponge. The oxygen and hydrogen analyses spotted throughout the heats indicate the range of interstitial levels resulting from the melting practice used. Heats D and I were melted as 20-lb ingots with the same grade of sponge. These ingots were cut in half and one portion used in the present evaluation. The ingots, which were about 4 in. diam and 4 in. in height, were upset forged and drawn at 1750°F to sheet bar 5/8 in. thick by 2 1/2 in. wide in such a manner that the top of the ingot corresponded to the top of the sheet bar. Slabs of the sheet bar, 5 1/2 in. in length were scalped to 1/2 in. thickness and rolled at the temperatures indicated in Table I to approximately 0.055 in. sheet. Elongation during rolling took place at 90" to the original forged length. The fabrication procedure used is described in some detail since the experimental heats showed considerable directionality in mechanical properties. The rolling procedures for the commercial heats were unknown, but were such as to produce essentially isotropic properties. All heats, as rolled, showed microstructures typical of alpha-beta alloys worked in the alpha-beta field; that is, the structures consisted of equiaxed alpha particles in a beta matrix. Heat Treatment— The effects of solution and aging heat-treatments on the properties of the alloys were evaluated uSing longitudinal and transverse tensile and bend coupons sheared from the sheet. Two or three solution-treated conditions were evaluated for each alloy. In addition, the alloys were also tested after annealing at 1200°F for 4 hr and furnace cooling. The solution-treated and annealed conditions were those in which the alloys might be expected to

Jan 1, 1959

By S. Feuerstein, L. Rice

The effect of low pressures on the flow and fracture behavior of molybdenum is described. For poly crystalline samples, room-temperature tensile tests indicate greater ductility under 10 Torr than under intermediate pressures up to and including atmospheric pressure (760 Torr). In addition, tests conducted at 760 Torr under atmospheres of air, dry nitrogen, and purified argon exhibited no apparent difference in mechanical properties. Critical tests involving baking in situ as well as those involving single-crystal deformation further imply that the ductility effect is a pressure-dependent phenomenon related only to the fracture process. This dependency is discussed in terms of adsorption and diffusion contributions. THE effect of very low pressures on material properties has heretofore been presumed to be important only for substances possessing relatively high vapor pressures at ambient temperatures. Research has therefore been concentrated primarily on organic solids and liquids, and in some instances on metals such as zinc and cadmium. Most vacuum-effect studies&apos; on the mechanical behavior of metals have been performed under conditions of either cyclic loading or creep rupture at elevated temperatures, i.e., over extended time periods. These studies were not restricted to high vapor pressure materials but also encompassed such metals as gold, copper, and nickel. Very little concern, however, was placed upon the importance of a vacuum environment on the mechanical behavior of metals subjected to a simple unidirectional deformation at ambient temperatures. A tension test is generally of short duration as compared to a creep test, and at room temperature vacuum effects if any would be expected to be surface-limited. In early 1963, Kramer and podlaseck2 reported a change in the bulk flow behavior of aluminum single crystals during room-temperature tension tests. The deformations were performed under pressure conditions of 760 to 3.4 X 10-8 Torr and indicated for the first time a vacuum surface effect contributing to the bulk tensile behavior of metal specimens. As a consequence, an experimental program was initiated in this Laboratory to study the effects of ultrahigh-vacuum conditions on the mechanical behavior of metals. The results of a preliminary study on poly-crystalline molybdenum3 revealed, unlike Kramer&apos;s observations of changes in the stress-strain behavior, only an increased ductility under ultrahigh vacuum. Flow behaviors were nearly identical for all tests re- gardless of pressure. This paper presents comprehensive results obtained in this area of research. 1) EXPERIMENTAL PROCEDURE Three material categories were used in this study: sintered and are-cast polycrystalline molybdenum of nominal purity 99.93+ pct and single-pass electron-beam zone-refined molybdenum single crystals having a nominal purity level of 99.99+ pct. The interstitial levels (weight percent) as determined by the Materials Testing Laboratories, Division of Magnaflux Corp., were as follows: sintered molybdenum (C— 0.005, H—0.0004, O—0.015, N—0.008); and arc-cast molybdenum (C-0.0038, H-0.0003, O-0.015, N-0.023). Single-crystal molybdenum obtained from Materials Research Corp. had a typical interstitial analysis of C-0.0015, H-0.00007, O—0.00045, and N-0.0001. Tensile specimens having a 5 mm diam by 50.8 mm length were prepared from these materials. An average grain diameter of 0.059 mm was obtained for the sintered specimens following a 4-hr, 1600°C heat treatment. Grain sizes from 0.019 to 0.149 mm were obtained in the arc-cast specimens following heat treatments from 1100° to 1600°C for 1 hr. This series of specimens was used exclusively for the grain-size effect studies. All samples were electrolytically polished in 97 pct sulfuric acid solution prior to testing. Experiments were performed at room temperature in an ion-pumped ultrahigh-vacuum system positioned in an Instron tensile machine, Fig. 1. A constant strain rate of 4.2 x 10-4 sec-1 as derived from crosshead displacement was assumed for the deformations. Starting vacuums ranged from 2 to 0.5 X 10-10 Torr. These pressure measurements were made using corrected values4 of an NRC Redhead gage. Comparative readings were also made against a G.E. triggered dis-

Jan 1, 1967

By H. A. Bourne, E. L. Haden, D. R. Reichmuth

A circumferential-toothed bit with novel tooth form gave improved penetration performance. In this design the exterior flank of all teeth were vertical when in rolling contact with the hole bottom. Rock chips were generated by the interior flank of the tooth displacing the rock inwardly and downslope toward the center of the hole. A unique two-cone laboratory bit assembly enabled evaluation of numerous cone and tooth configurations. Some of the variables investigated, in addition to weight on bit, rotary speed and rock type, were tooth interference, percent tooth, hole bottom angle, attack angle and relief angle. Most tests were conducted dry on a brittle synthetic sandsone or a ductile quarried limestone. Tooth configurations were found to be more significant in the ductile material. This was attributed to the deeper tooth penetration before rock failure. These studies showed that the attack angle (angle beween interior flank of the tooth and rock surface) was the controlling variable; changing the tooth configuration from the assymetric or semi-wedge to the more conventional symmetric or wedge form reduced penetration performance; and penetration performance of circumferential-type cutters was directly proportional to rotary speeds up to 200 rpm. INTRODUCTION Much of the published literature on rock-chisel interactions describe experiments wherein symmetrical wedges are vertically loaded or impacted against a smooth rock surface.1-6 are is usually taken to insure that the indentation is not made near the edge of the rock specimen less erroneous data be obtained. The literature describes relatively few studies in which the investigator deliberately attempted to take advantage of an edge or free surface. In contrast, anyone who chips ice or breaks up a concrete sidewalk almost always works near an edge. Chisel "indexing," which has been considered by some investigator1,2,6,7 makes limited application of an edge or free surface. Probably the best documented investigation into applying this idea to drilling was that of Drilling Research Inc. at Battelle Memorial Institute.&apos; Their "annular wing" percussion bit consisted of paired asymmetric chisels oriented so as to produce and move chips to the center of the hole. They predicted that the lowest energy requirement for chip generation would be achieved with a stepped hole bottom having a median angle of 45" to the horizontal. Results from limited tests showed that approximately 50 percent of the rock fragments were large and semi-circular in shape, as would be expected by a chisel impact near an edge. The remaining 50 percent were fine chips produced by the chisels in re-establishing the steps or ledges. Initial penetration rates with this bit were high, but they rapidly decreased. This was the result of excessive tooth wear caused by the constant friction on the gauge surfaces. The basic idea — circumferentially placed asymmetric chisels — still appears to have merit. If the concept could be applied to a rolling cutter bit, two of the shortcomings of the fixed chisel design could be overcome: (1) reduction in tooth friction, and (2) greatly increased cutter surface. Adapting asymmetric chisels to cutters rolling on an inclined hole bottom is restricted by bit geometry. The basic elements of roller rock-bit construction prevents the practical attainment of a 45" hole bottom angle. Nonetheless, experimentally it was considered desirable to investigate the influence of hole bottom angle to at least 40". This paper describes the laboratory studies conducted in evaluating the circumferential-toothed roller cutter rock bit. EXPERIMENTAL APPARATUS AND PROCEDURE BIT ASSEMBLY The cost of constructing a sufficient number of conventional three-cone rock bits to investigate circumferential cutter performance was prohibitive. Instead, a novel two-cone laboratory assembly which used an external bearing system was designed and constructed. The external bearings made it possible to alter the journal bearing angles and thus allow a wide flexibility in cutter configuration. Fig. 1 shows the laboratory bit assembly, the various bearing mount plates and the appropriate roller cutters for drilling shallow holes having hole bottom angles of 0, 10, 20, 30 or 40". The bit was limited to a drilling depth of 1 1/2 in. at the gauge teeth and a hole diameter of 43/4 in. This more or less intermediate size bit was chosen because it gave a more realistic match between bit teeth and the rock than would a microbit. Also, the rock sample size required was convenient and easy to obtain. CIRCUMFERENTIAL CUTTERS The tooth configuration used in our initial studies is shown in the upper half of Fig. 2. All cutters used in this series had the same tooth form — 43" included tooth angle, 2" positive relief angle and a horizontal tooth flat width of 1/32 in. Each cone cuts alternate rows except for the gauge row. The row-to-row spacing in view was 1/4 in. Static loading tests conducted earlier with asymmetrical chisels had been used to establish this spacing. These tests showed energy requirements for chip production increasing rapidly as the distances to the edge increased beyond

By E. A. Ernst, N. F. Carpenter

The benefits derived from an acidizing treatment are a function of the penetration achieved by the acid before complete spending. Additional penetration may be achieved by (1) controlling acid leak-08 into formation pores in the channel faces, and (2) retarding the reaction rate of the acid. A recently developed chemical additive consists of a synthetic polymeric material which absorbs hydrochloric-acid solutions, when suspended therein, swelling up to 40 times its original volume. These swollen particles have the ability to deform and seal-08 formation pores, providing fluid-loss control. In addition, they provide a diffusion barrier between the fracture face and the acid solution, prolonging the spending time of the acid. Field applications of this new technique have shown promising results. A method of conducting acid fluid-loss tests, using carbonate cores, is believed to provide fluid-loss data that are more representative of formation conditions than the conventional filter-paper determinations. INTRODUCTION The concept of oilwell acidizing has changed since its first commercial application, 30 years ago. Originally, it was visualized that the acid penetrated thousands of tiny pores and flow channels in the matrix rock, enlarging them by dissolving the carbonate walls. The resultant permeability increase was assumed to be the responsible factor in increasing production from the well. Recent laboratory studies,&apos; however, have shown that this does not provide the complete picture. Although this type of individual pore penetration by the acid does take place during acid "soaks", designed to overcome "skin effect" due to mud invasion in the immediate vicinity of the wellbore, many years of experience have shown that considerable pressure is required to attain any appreciable injection rate into the fine capillary pores of the rock. During most acidizing treatments, the bottom-hole pressure build-up due to the restriction of flow into the formation exceeds the "breakdown" pressure of the rock so that a fracture is induced. In most cases, such fractures open up along natural, incipient fissures and zones of weakness in the rock and, therefore, tend to follow the natural stress pattern of the rock—whether it be horizontal, vertical or inclined. Because of the comparatively greater permeability of the channel in relation to that of the matrix, the bulk of the acid volume is diverted into the newly opened fracture. Here it quickly penetrates the formation, opening and ex- tending the fracture in much the same manner as a conventional fracturing fluid. Unlike the fracturing fluid, however, most acidizing solutions contain no propping agent; thus, the open fracture will again close when the injection pressure is relieved. Laboratory studies2 have shown that in many cases the etching of the fracture faces, resulting from the reaction between the acidizing solution and the carbonate rock, is nonuniform due to the heterogeneity of the rock structure. As a result, the two fracture faces no longer match when pressure is released, and support pillars and intermediate voids remain, forming a high-conductivity channel for well fluids. Unfortunately, this is not true over the entire area of the fracture, but only over that portion of the fracture where the rock has been partially dissolved by the acid. The acid solution spends as its travels away from the wellbore; once it has completely spent, even though it may provide additional mechanical fracture extension, no additional benefit due to etching of fracture faces can be expected. Studies of acid reaction rates under formation conditions,3 observing the effect of different variables upon spending time, have shown that the reaction was often so rapid that very little penetration of the formation occurred before the acid was spent. Study was undertaken to devise methods of increasing the penetration of the acid before spending, so as to provide greater benefit from the acidizing treatment by etching a greater portion of the fracture faces. Several techniques were devised to accomplish this purpose. First, chemical additives were developed which were designed to retard the reaction rate of the acid, causing it to penetrate a greater distance from the wellbore before finally becoming spent. Another method was to increase the injection rate of the acid. However, it was found that the resultant increased shear tended to accelerate the reaction rate of the acid, partially offsetting the benefits of the higher injection rate insofar as achieving increased penetration before spending was concerned.&apos; Another approach to the problem of achieving increased penetration was the development of fluid-loss additives for acid solutions, which would minimize the volume of acid lost into formation pores in the fracture faces and provide maximum fracture extension for the volume of acid injected during the treatment. The use of fluid-loss additives is now considered the most effective method of providing maximum fracturing-fluid efficiency.~ Unfortunately, this latter technique does not solve the problem of rapid reaction rate, with consequent limitation of the fracture area benefited by reaction with unspent acid. A newly developed acid additive overcomes many of these limitations by providing the dual benefits of fluid-loss control and mechanical retardation of acid reaction

By G. Borelius

ABOUT the turn of the century, Gibbs&apos; thermo-dynamic theory of heterogeneous equilibrium, on the one hand, and the experimental methods of thermal and microscopic analysis, on the other, gave to the physical metallurgist his first scientific tool, the equilibrium diagram. The classical equilibrium diagram of a binary alloy system shows the boundaries between ranges of homogeneous and heterogeneous equilibrium in their dependence of concentration and temperature. A homogeneous solid sohtion which on cooling passes such a boundary is assumed to precipitate, forming a mixture of two phases with different concentrations. The equilibriunl diagram and the equilibrium theory, however, give no information about the time scheme of the process or the intermediate states passed during precipitation. For this reason it satisfies neither the practical need of the metallurgist nor the curiosity of the physicist. As a matter of fact, in the heat treatment of alloys for technical use the objective very seldom is the equilibrium state. Thus good mechanical properties of construction material are connected, for the most part, with some intermediate state. As these intermediate states are thermodynamically unstable, there is, from a theoretical point of view, always to be expected a decay of the good properties with time; and it is a matter also of practical interest to know whether this natural life time of a material is of the order of, say, ten or thousands of years. Thus, for many reasons, there is a current demand to complete our knowledge of equilibrium through knowledge of the kinetics of the precipitation phenomena. From the point of view of the physicist, the most interesting question in this case is whether there are any general laws governing the kinetics. According to a generally accepted view, precipitation is ruled by two more or less independent phenomena, the formation of nuclei of a new phase and the growth of these nuclei. It is also commonly accepted that there is a tendency for the velocity of growth to increase with increasing temperature because of the increasing mobility of the atoms. There is also a tendency for the velocity of growth to decrease in the neighborhood of the two-phase boundaries. So far, however, very little is known quantitatively about this fundamental phenomenon in the case of solid metallic systems. In our laboratory attention has been directed especially toward the nucleation phenomena, and a series of measurements have been carried out with the guidance of a work- ing hypothesis (based on experiences from previous work on order-disorder transformations in alloys) about the influence on the nucleation of thermo-dynamic potential barriers. However, before discussing the experiments, the theoretical ideas will be considered. In a binary solid solution the arrangement of atoms on the lattice points approaches with increasing temperature a state of full randomness, as illustrated by the ball model of Fig. 1, that might represent a [111] plane of a face-centered alloy with 30 pct "black" and 70 pct "white" atoms. In reality the atoms are changing places continually with their neighbors so that the picture should rightly have been a moving one. On account of this thermal motion the concentration of black atoms within a certain group of, say, a hundred or a thousand lattice points fluctuates with time around the bulk concentration of 30 pct in a manner governed by statistical laws. With decreasing temperature two independent changes in this state grow more and more important. First, the mobility of the atoms decreases, and second, the forces between the atoms will have an increased influence on the fluctuations. In alloys with a tendency for precipitation, which are the concern of this lecture, the distribution function of concentration fluctuations will broaden, so that the relative probability of great local variations from the bulk concentration increases. Fig. 2 gives an example of such a fluctuation. When the alloy is supercooled below the solubility limit into the range of two-phase equilibrium, the fluctuations will now and then at some point give rise to a state that resembles the equilibrium state and thus will form a stable nucleus that is capable of growing by diffusion processes. In discussions with colleagues and in the literature, I have often encountered the idea that three or four atoms of the dissolved metal could form a nucleus of the new phase. A look at the ball model might be enough to indicate that this cannot be true. If it were true, there should be nothing but nuclei, whereas we know from experiment that nucleation must be a rather rare occurrence. In fact we have, as will be mentioned later, certain reasons to believe that the nuclei are formed by fluctuations containing some hundreds of atoms, which should be the order of the number of black balls in the fluctuating group of the figure, if it were extended into three dimensions. As a working hypothesis we have assumed that the fluctuations producing nuclei, though large and rare, still are ruled by the distribution laws of fluctuations of the supercooled solid solution in its initial state. Thus the probability of nucleation will be connected to the thermodynamic properties of the solid

Jan 1, 1952

By G. M. Gay, R. L. Perrine

This paper describes a method of numerical computation for three-dimensional, unstable, miscible displacement behavior useful for heterogeneous systems, as well as for more ideal conditions. In the method, flow equations are first linearized by a perturbation approach. The basic flow process is separated and a solution for its behavior readily obtained. The remaining problem of deviations from the basic flow caused by non-ideal conditions is then subjected to numerical analysis. Results obtained from use of the method are also presented. Although conditions assumed in the test cal-culations were severe, results show the type of dispersing flow expected and appear quite satisfactory. The method has eliminated or reduced in importance problems of oscillating values near steep fronts, excessive computer smoothing, etc. A unique advantage of the method is that the source of variations from ideal behavior can be observed. ,The one serious drawback results from the algebraic complexity of the perturbation approach, and the need for second-order terms to be retained in calculations of interest. Fewer array points are available and more computer time is required than would be desired. However, these difficulties are also experienced with other approaches to the solution of three-dimensional dispIacement problems. INTRODUCTION Prediction of behavior of the miscible displacement process within a porous medium for any system of engineering importance is plagued by a number of difficulties. With typical fluid properties the displacing fluid has the lower viscosity, and there is a natural tendency toward flow instability. The problem of predicting instability is compounded by the fact that every real system is heterogeneous. Permeability will vary from point to point — not entirely systematically, and yet not in a random fashion leading to a readily defined average. Furthermore, permeability is unlikely to be isotropic. These permeability properties, which are characteristic of any real porous medium, accentuate the effects of flow instability. Another factor to be considered is that flow dispersion accompanies the displacement process in a porous medium. Mechanistically, dispersion is due to the fact that flow between any two points in the medium follows multiple tortuous paths, each characterized by slightly different flow properties. The fact that the coefficient characterizing dispersive properties of the real medium JS a tensor with variable elements complicates matters. Further difficulties arise because the parabolic influence, while not negligible, is small. Thus, there is a tendency toward steep and uneven displacement fronts along which dispersion smoothing must be represented accurately. Yet frequently used numerical analysis schemes may tend toward either instability, oscillation or excessive smoothing, none of which gives the desired accurate picture of flow behavior. Thus, while many experimental and analytical studies of the process have been made, predictions of actual performance are still subject to considerable uncertainty and possible improvement. This paper reports on part of a study which attempts to develop improved methods for solution of the flow equations describing the miscible displacement process. Of necessity, the calculations were performed on a large digital computer. A three-dimensional system is represented, and the coefficients defining dispersion and permeability can be varied in a manner representative of a real system. Because the differential equations are nonlinear, a first step is to linearize them using a perturbation approach. Objective of this approach has been to separate the basic flow which would occur in an ideal system and for which predictions are readily made. Then the numerical analysis, which is necessarily complex, is directed toward solution of the perturbation equations. These equations state how the basic flow is modified

Jan 1, 1967