Search Documents

By H. H. Hausner, H. S. Kalish

M. Hansen—This paper certainly is an interesting study. Although I have not had too much experience in the powder metallurgical methods of studying phase equilibria, I would like to say the following concerning the interpretations of the results obtained: 1. The existence of a zirconium-rich eutectic having a melting point close to 950°C and containing approximately 5 pct beryllium is well established. 2. Undoubtedly sintering of the original compacts (i.e., without repressing and resintering at 1350°C) resulted in a condition being far from equilibrium, even in the low-melting point zircon-rich region where undissolved zirconium particles have been observed. This means that only partial reaction between the component powders has taken place. 3. In preparing and handling powder mixtures for pressing and sintering, we have found that with powders differing considerably in density, and also in particle size, separation in layers of different composition may occur. This means that a concentration gradient would exist within such samples. This phenomenon may, at least to some extent, account for the difference in microstructure of the top and bottom regions of some of the sintered samples. If this is the case, density figures for some of the nominal compositions would not represent actual densities of those mixtures. 4. Fig. 1 shows that the low densities of mixtures with 40 and 60 pct beryllium sintered at 1350°C are changed to much higher densities if the products sintered at 1100°C are repressed and resintered at 1350°C, whereby an approach toward equilibrium takes place. This would mean that the low density and growth in volume is due to nonequilibrium conditions. If this is true, would it be justified, then, to conclude that "the remarkable growth of the alloys in the vicinity of 40 to 60 pct Be indicates the formation of a high-melting point phase, probably accompanied by a considerable change in volume due to a large alteration of the crystal structure from that of the original compounds"? If some compound formation has taken place already during the first sintering at 950" to 1350°C, more compound would be formed by repressing and re-sintering of the 1100" samples. This treatment, however, results in higher, rather than lower, densities. In general, the density-composition curve of alloy systems containing one or more intermediate phases is characterized by a more or less defined contraction (decrease in specific volume, increase in density) over the "theoretical" density. Does not discrepancy exist between the two statements that "growth of the alloy indicates the formation of a high-melting phase . . ." and "even at 1350°C, no indications of sintering have been observed"? 5. I am not sure that the explanation given for the fact that fig. 4 did not reveal as much eutectic as the top portions of the mixture with 2 pct Be, is correct. The density of the melt containing only 5 pct Be or even perhaps less, is not too much different from that of the nominal composition. The reason might be also that there was already some separation of the components in the pressed compact. 6. I do not understand why the microstructure of the bottom regions of the compact with 5 pct Be (fig. 6) is so different from that of the top regions (fig. 5). The compact was melted on sintering at 1100°C. Its composition lies close to the eutectic point. There should be at least some lamellar structure in the bottom regions too; otherwise, the composition of top and bottom must have been very different after sintering, because the eutectic is said to extend as far as the composition ZrBe2. In case the white and gray areas of fig. 6 are both gamma, and the black areas undissolved zirconium, this composition would be close to the phase coexisting with zirconium, that is, ZrBe2, according to the hypothetical diagram, or a compound richer in zirconium. 7. Figs. 9 and 10 are not mentioned in the text. 8. The great difference in microstructure of the composition 20 pct Be of figs. 8 and 14 on one side and fig. 15 on the other side proves that sintering at 950" and 1100°C results only in partial reaction of the powers. 9. The mixture with 60 pct Be (fig. 19) seems to consist of two phases, rather than one phase, one interspersed in a matrix of another. 10. The statement that the eta phase "may be an intermetallic compound or the product of a peritectic or monotectic reaction" seems to be misleading, because the product of a peritectic or monotectic reaction in this region of the system must be an intermetallic compound. 11. If there is some solid solubility of Be in alpha and beta-Zr, it would be expected to be higher in beta-Zr (b.c.c.) than in alpha-Zr (h.c.p.). The temperature of the polymorphic transformation of zirconium then would be lowered, rather than increased. In accordance with this, Battelle has found that the transformation point of titanium is decreased by beryllium. 12. In case the phases present in alloys with 80, 90, and 95 pct Be are identical (which appears to be correct), it is striking that the relative amounts of both phases (eta and beryllium) are not too different within this wide range of composition. With 60 to 65 pct Be

Jan 1, 1951

By Carroll F. Hardy

The day by day loss of industrial plants to gas and oil is chiefly by default. The coal industry is not selling its superior economy, safety, and other advantages to its customers. THE position of the coal industry has been affected by a wide variety of developments in the production and use of energy. The tempo of development and change has been increasing and the end is not in sight. Legislation is currently being proposed for commercial use of atomic power, and the employment of atomic energy in significant quantity will probably occur about the same time as the decline in production of petroleum and natural gas. But these developments are in the future and have little immediate effect on utilization and marketing of coal. While no one should try to suppress or retard the development of a new and economical source of energy, both the coal and private utility industry should be allowed to question how the nuclear power is to be used, who is to use it, and who is going to pay for it. The taxpayers have a monopoly on fissionable material and the knowledge to employ it. Any commercial use must stem from this source. It is not hard to visualize either taxpayer-subsidized private utility atomic power plants on one hand and super TVA's on the other. In view of the gains of gas and oil in the home heating field, it is interesting to compare the 1940 and 1950 census reports on the kind of fuel used for heating in occupied dwelling units. Table I shows that whereas coal provided 77 pct of the fuel for central heating (furnaces and boilers) in 1940, it was down to 45.4 pct in 1950. However, only about 1 1½ million units were lost in this 10-year period. In the non-central heating category, which principally includes stoves, the percentage declined from 39.2 to 25.6, but the units declined about 2½ million in number. The big increase was in heating units designed to burn gas and oil. Use of wood for central heating declined about one-third. Data on amount of fuels used for residential heating are not available, but information is on hand for residential and comnlercial space heating, see Table 11. Commercial space heating includes office buildings, churches, schools. and similar structures. The annual use of bituminous coal in these two categories declined about 1 million tons in the 10-year period. Other forms of solid fuel showed greater losses, except wood, which remained the same. Domestic stokers reached their high point in 1948 with about 1,200,000 in use. At the end of 1951 there were approximately 1,116,790 stokers in use. Conversions to gas and oil have been from hand-fired heating plants in the ratio of about 7 to 1 compared to stokers. In other words, for every one stoker which has been converted to gas or oil, seven hand-fired units have been converted to gas or oil. A bare recital of these data would indicate that the coal industry is holding its own reasonably well. However, 93.4 pct of the new homes built in 1951 were heated by gas or oil. Oil-burning equipment was installed in 37.8 pct and gas equipment in 55.6 pct of the new homes. This indicates that the public prefers gas when it is available, and that oil is second choice, with all forms of solid fuel apparently used when it is unavoidable. It must be pointed out, however, that during the period of rapid expansion of gas pipelines gas has been sold for house heating at prices that are in some cases actually lower than coal prices, or very nearly on a par. Gas has been sold at wells at far below the comparable price for oil produced from the same wells, and far below its actual worth. This situation is being remedied at the present time by increases in gas prices at the wells. For example, the wellhead price of gas in Texas averaged 7.494 per Mcf in 1952. In 1949 it was 4.59c per Mcf. This increase in price is being reflected in pipeline gas prices, and in most of the markets served by the pipelines the tendency is to get it out of the bargain basement type of sales. The American Gas Association estimates that at the end of 1952 there were in the United States about 11 million customers for gas house-heating, and the Association expects additional gains each year until around 18 million homes will be heated by gas in 1975. By 1975 there should be 60 million dwelling units to be heated in the United States, if dwelling units increase at the same rate as the population. If the gas industry heats 18 million dwelling units by that time, this still leaves 42 million units to be heated by some other fuel. If oil is used to heat 18 million dwelling units in that same year, 24 million would of necessity be heated by coal, coke, wood, electricity, or another fuel. The total number of dwelling units using coal listed in the 1950 Census was 18,776,000, so it would appear that coal has a chance at least to stand still in the tonnage sold for domestic use. In the first quarter of 1953, 2044 domestic stokers

Jan 1, 1955

By W. W. Vaughn, R. H. Barnett, E. E. Wilson

Soon after the search for uranium ores on the Colorado Plateau began in earnest, thousands of feet of drill core ranging from 1 1/8 to 2 1/8 in. diam became available for study. Although significant advances had been made in the technique of quantitative gamma-ray borehole logging, instrumentation was in the development stage, and complete reliance could not be placed on gamma-ray logs alone to interpret quantitatively the meaning of radioactivity in a drillhole. A method that would be faster than chemical analysis and still give reproducible and reliable results for various drill core sizes was desirable to provide additional information on the enormous footage of drill core being accumulated. A solid phosphor scintillation drill core scanner was designed and constructed. Basically the instrument was developed to measure radiation from a drill core which would not be clearly recorded by a gamma-ray logger using a Geiger tube as the sensitive element. Such data would be beneficial in constructing isorad maps to delineate ore-bearing zones. A calibration in the range 0.01 to 0.1 pct eU.,O, was provided; above 0.1 pct eU3O8 gamma-ray logs were available and were being used to calculate grade and tonnage of ore reserves. The core scanner, however, has been used to estimate equivalent uranium content of ore-grade materials containing as much as 2.2 pct eU3O8 with an accuracy of ± 10 pct, the sample being in the form of a BX drill core. Actually, an apparent calibration of eU3O8 vs counts per unit time is a straight line with a slope that is a function of the sensitive element and the geometry of the counting assembly. A true calibration that will show the expected departure from a straight line is due principally to the random nature of the pulse from a radiation source and the nonlinearity of the electron circuitry. Design and Construction: Three methods of detecting radioactivity were considered and applied in developing the core scanner now in use: 1) the Geiger tube, 2) liquid scintillation phosphors, and 3) solid scintillation phosphors. The desired sensitivity and long-term drift characteristics needed for this operation could be attained only by using solid scintillation phosphors. All three methods are discussed. Before scintillation counters were common, nine beta-gamma sensitive Geiger tubes 7/8 in. diam by 12 in. long were used, arranged to surround the drill core with tube axes parallel to the axis of the core. This arrangement of Geiger tubes was en- closed in a lead shield 1 in. thick, and provision was made to slide a 6-ft length of drill core manually into the counting chamber, one foot at a time. A count for each segment was taken with a scaler while the core remained stationary. The equivalent uranium content of the different sections of drill core could then be estimated with the aid of a calibration curve of counts per unit time vs percent equivalent uranium (eU). In rare cases the effects of the radioactivity concentrated in small areas within the core introduced errors in the readings made with the Geiger tube arrangement owing to the geometry of the measurement. The variability of counting rate due to a localized concentration of radioactivity in a spot in the wall of a drill core is illustrated in Fig. 1. This effect and the inherent low efficiency of the Geiger tube were considered major disadvantages of this counting arrangement. When liquid scintillation phosphors became available the core scanner in Fig. 2 was constructed to make a more accurate measurement of the equivalent uranium content of a sample. This instrument contains about 4 liters of liquid phosphor in a stainless steel coaxial cylinder 1 ft long, with inner and outer walls 0.060 in. and 0.125 in. thick, respectively. Four end-window type photomulti-plier tube with cathodes of 2 in. diam, immersed in the solution at right angles to the axis of the core, were used to observe light flashes in the phosphor. The liquid phosphor offered equal sensitivity to radiation originating at any point in the enclosure and represented geometrically the optimum in design. However, providing a semi-permanent leak-proof seal between the glass envelope of the phototube and the metal walls of the container proved to be a serious problem in constructing the equipment. The most effective seals were especially machined O-rings from sections of large tygon tubing. The tygon took a permanent set owing to cold flow characteristics and in most cases sealed completely. The light absorption characteristics of the liquid phosphor changed gradually with time, and after one month the counting rate had decreased to half the original value. The most sensitive liquid phosphor tested proved to be a solution containing 4 g of 2.5-diphenyloxazole and 0.01 g of 2-(1-naphthy1)-5-phenyloxazole per liter of toluene. With fresh solution in the chamber and with all photomultiplier tubes operating in parallel, the counting rate contributed by any one of the four photomultiplier tubes was about 85 pct of the counting rate from a single tube operated individually. From these observations it was concluded that owing to coincident loss and light attenuation within the liquid phosphor, the apparent sensitivity could not have been materially increased by additional phototubes. However, this approach to core

Jan 1, 1960

By W. J. Slatosky

W. 0. Philbrook (Cairiegie Institute of Technologyogv—Mr. Slatosky has presented an interesting and constructive paper that represents another step along the way of converting steelmaking from an art to a science. I am confident that his computer will be practical and successful and that with a very few months of experience it will provide a significantly better degree of control than his record of 65 pct of heats within range obtained with the slide-rule calculator . A paper such as this, with a lot of symbols and condensed mathematics, is difficult to comprehend quickly. Since I have had an opportunity to study it carefully, perhaps my evaluation of its validity and accomplishments will save time for others. Mr. Slatosky has correctly used standard principles of stoichiometry and heat balances, which are available to anybody, but he has also brought to them two original contributions: 1) He has developed from operating data some empirical relations for predicting the final FeO content of the slag (at 0.5 pct C end-point) as a function of slag basicity, lance height, and scrap, ore, and scale in the charge. This improves the accuracy of prediction of temperature or scrap requirement compared with assuming an arbitrary, constant FeO content at the end of each heat. There is no assurance yet that exactly the same relations will hold for other furnaces or practices, but similar correlations can be expected. 2) He has combined calculations that are ordinarily carried out laboriously as a number of individual steps into a single, simple linear equation that can readily be fed into a machine. This involved a tremendous amount of painstaking detail work as well as the imagination to see the possibility and work out the steps. While his particular Eqs. [3] and [6] are valid only for the furnace design, charge weight, and blowing time used at Aliquippa Works, only a few numerical values have to be changed to adapt it for other conditions. In order to arrive at a useable solution, Mr. Slatosky had to make some basic assumptions about the process that are similar to those used by others. He neglected variation in some process variables and assumed an arbitrary average value for waste gas analysis and temperature for want of more exact information at the present time. All of these judgments are clearly stated. In addition, some thermody-namic data presently available are not adequate for the job, notably in relation to heats of formation and sensible heat in slag, and some expedient has to be adopted to get around the difficulty. Other people might prefer slightly different judgments about these details and hence obtain somewhat different numerical solutions. This is not of serious importance, however, because the errors accumulate in the "heat loss" term and are largely self-compensating for a constant heat time. Although the extended Eq. l(a) in Appendix I was set up as a rate equation originally, for convenience in using an analogue computer as stated in the paper, the time dependence was removed by later mathematical manipulations and assumptions about the process. The final result is an integration of element and energy balances from initial to final states; this procedure is as legitimate here as in any other form of heat-balance calculation. The formal handling of stoichiometry and thermochemistry appears to be correct, and it is assumed that any arithmetical errors would have come to light in applying the calculations to furnace practice. Mr. Slatosky's approach is not necessarily unique, in that other people might start with apparently different equations or prefer another form of final equation for another type of computer. However, he has presented an accomplished result that appears to be a theoretically sound and practically useful way of applying scientific principles and rapid computation for better control of steelmaking. His success will undoubtedly encourage himself and others to improve on the mathematical model and its use as better informatioq becomes available. John F. Elliott (Massachusetts Institute of Teck-t2ology)-The last comment by Mr. Richards that a calculator is quite unnecessary for an L-D operation ?-equi??es a rebuttal. The L-D furnace is a very high capacity process which places a premium on close control. When one is making steel at rates between 100 and 200 tons per hr, one cannot afford the luxury of an extra 5 or 10 min at the end of a heat correcting for an error that should never have been made in the first place. Mr. Slatosky's paper is a very sound application of the simple principles of stoichiometry and the energy balance. It is a satisfactory and valuable start, but only the start of the development of methods of control for this process. An analysis of the process shows that it should be very suitable to control by a computer. This is especially the case when various grades of steel are to be made. In fact, it would seem that the organizations who are planning new and bigger installations of L-D vessels should consider carefully the advantages that would stem from computer control of a vessel with the operator present to do little more

Jan 1, 1962

By Ernest O. Kartinen

This report is the accumulation of eight years of experience on only one small phase in the business of oil production. It is not intended as a final report but rather as a progress report dealing with the internal corrosion of oil field dehydrating tanks. The corrosion of dehydrating tanks continues to be a problem in the production of crude oil. The deterioration hy corrosion of these tanks falls into three general classifications: (1) Atmospheric corrosion of exterior areas, (2) corrosion of the underside of deck and the rafters and top area of the upper row of staves in that part of the tank which is known as the vapor space, and (3) corrosion of the bottom and shell areas, and the steam coils which are normally immersed in water and thus exposed to the corrosive action of the water. Atmospheric corrosion is primarily a paint problem, and has been omitted in this discussion. The corrosion in the vapor space, in this company's experience, which has been of great concern only in one area. has also been omitted in this discussion. The third, and most troublesome type of corrosion, and the one with which this report deals, is that which occurs in the water-exposed areas of dehydrating tanks, and, to a lesser degree. in some stock tanks. The operating temperature of these waters varies from 80°F to 160°F and the salt counts run from a few thousand to as high as 25.000 parts per million. Corrosion in these tanks occurs in three forms: (1) pits, (2) ringworm type of attack along the vertical and horizontal bolt seams, and (3) as a general attack, spread over a wide area. Steam Coils In dehydrating tanks, our experience has been that the steam coils are the first to show signs of corrosion, and then the shell and bottom areas. This action is not uniform throughout this company's operations. Some installations have coil troubles with very little tank trouble, and some show just the opposite. But in the majority of cases the coils are the more seriously corroded areas. This may be partly due to the fact that we have tried by periodic application to keep a protective coating on the interior areas of the tanks, and some protection has been afforded by these coatings. Through the years several types of hot and cold coatings have been tried with many various methods of cleaning the steel, ranging from use of cleaning solvents to hot and cold Oakite washes, as well as sandblasting. Although experience has shown that a longer life expectancy of a coating is possible after a very thorough steel cleaning job, it has still been necessary to recoat these tanks at least every two or three years. Until a few years ago, vertical spiral steam coil bundles were installed when the tanks were originally erected. When these coils needed replacement, in some cases within 18 months, it was necessary to remove a couple of shell staves to accomplish this task. This required a down time period of several days and was often very inconvenient to the production operations of the leases. This problem was considered on the basis that the coils were expendable, and thus. to eliminate any unnecessary down time when changing coils, the vertical spiral coils were discarded in favor of horizontal flat coils which could be taken in and out of the tanks by way of the cleanout openings, and put together with unions. This made a fairly easily replaceable and repairable coil. But it was still very much of a nuisance when repairs were necessary. Efforts to increase the useful life of the dehydrating tanks led to the adoption of galvanized tanks at an increased initial cost. The zinc coating was depended upon for protection and no other protective coatings were applied. In July, 1944. during the development of a new lease, a 3-ring 1,500 bbl, black iron water tank was converted into a dehydrating tank with steam coils to handle the new production. This tank was coated inside with a cold, brushed-on coating, for protection against corrosion. After approximately 18 months of service, holes developed in the tank and the steam coils. The tank was emptied and cleaned for repairs. The coils were so badly pitted that it was felt advisable to replace them. Coating Becomes Loose Inspection of the tank showed the protective coating to be still in place but loose, and numerous blisters were in evidence. A closer inspection showed that the interior of this tank was so badly pitted under the coating that any further attempt to use the tank was inadvisable. This tank was therefore discarded and a new galvanized tank ordered and set up at considerable expense and inconvenience. In April, 1946, another dehydrating tank installation was made on an adjoining lease. This installation consisted of a 1,500 bbl. 3-ring galvanized tank with two sets of flat steam coils 12 in. and 24 in. up from the bottom. In September, 1947. seventeen months after installation. salt showed up in the boiler feed water. When the dehydrating tank was opened and cleaned, the steam coils were found to be badly pitted — several holes having penetrated through the wall of the pipe. New coils were installed.

Jan 1, 1950

By James R. Stuart

AS the available remaining properties of iron ore reserves on the Mesabi Range are opened up for mining, the various properties located under lake beds are brought nearer an active status. The actual physical problems involved in stripping these properties do not act as a deterrent so much as the legal and political problems that are encountered. When it is proposed to destroy a natural lake that has been used by the public for many years, much local as well as state opposition may be encountered regarding its destruction. Public hearings must be held and some adverse publicity is likely to result. The ownership of the ore under the lake and the rights of the abutting property owners must be settled, and protection from damage caused by a disturbance in surface and subsurface drainage is likely to be demanded by property owners some distance from the proposed mine area. The Embarrass Mine, located near Biwabik, Minn., falls into this classification. A portion of the orebody lies under what was formerly Syracuse Lake, this body of water having been removed in the process of stripping the mine. An additional problem in the case of a meandered body of water is the establishment of a meander line that can be projected downward as mining progresses to form the basis for a satisfactory division between lake bed and upland ore shipments for royalty purposes. Fig. 1 illustrates the complications encountered in maintaining these divisions. A balance point was agreed upon in the center of the lake to make an equable division of lake bed ore to the abutting properties. The entire lake bed has since been adjudged the property of Minnesota. Lake Characteristics Lake bed stripping problems with which this paper is concerned necessarily are limited to a specific type of lake, namely the glacial lakes of the Lake Superior region. One characteristic common to these bodies of water is a deposit of fine black mud or silt on the bottom, frequently underlain by a layer of impervious blue clay. This is also true of the muskeg areas of the region, which present almost identical problems as lakes in stripping. The actual removal of the water and the lake bed material is a routine matter more or less standardized as to equipment, and the period of time required can be estimated easily on the basis of volume and capacity. More important than the foregoing is the execution of preliminary work, and above all, the timing involved. An account could be prepared based entirely on statistical and cost data which would give a very fair picture of the time required and cash outlay needed to effect the removal of a body of water preliminary to stripping the orebody. However, the real interest from the standpoint of the operator and the engineer who carry responsibility for completion of the job lies in the unexpected emergencies and the action of various materials involved in the stripping when the balance has been upset through diversion of water courses and the reduction of the lake level. Runoff and Drainage Lakes are located in natural basins that catch all the rain water and runoff water for a considerable area. Where a lake is involved having an inlet and outlet or a sizeable water course running through it, the drainage area may include a watershed covering many square miles. All available data then must be collected to supply a history extending over as many years for which information can be gathered on the flow of streams, annual rain and snowfall, and most important, the peak flows to be expected. Where the diversion of a stream around the stripping area is a part of the problem, this last factor is of great importance since it controls the cross-section to be selected for the diversion channel and the volume to be removed in its excavation, as well as affecting the hydraulic considerations to be met in the design of the completed channel. Characteristic material in the overburden found at the Embarrass Mine is illustrated in Fig. 2. Well Pumping Pumping from the well holes was started well in advance of the draining of the lake. Fig. 3 shows a gradual lowering of the water table with no noticeable fluctuations during the period in which the lake was being dewatered. Unfortunately, because of tight ground, a maximum flow to the wells was not maintained. This retarded the rate at which the water table was reduced so that in the course of stripping the excavation soon extended below the water table, and the great bulk of the pumping was handled from a system of sumps in the pit itself. Any dewatering program projected by prepumping from wells, a glorified well point system, would have to be started well in advance of the stripping to be of any great advantage. Preliminary drainage of the surface over the mine area is entirely apart from the actual elimination of the lake bed itself. Since the lake is what is called a perched water table because of the impervious character of the lake bottom, the adjoining surface may be dewatered below the surface of the existing lake and the flow will not be affected by the proximity of that body of water. This condition actually has been demonstrated through the establishment of a number of observation holes where a small churn drill was used to put down the holes and a 3-in. pipe was installed for taking water level

Jan 1, 1952

By J. J. Frawley, W. J. Childs

The dynamic nucleation of supercooled bismuth and Bi-Sn alloys has been studied over a frequency range of 15 to 20,000 cps. For low-frequency vibration, a minimum vibrational energy was required for enhancement of nucleation. Above this critical energy, the dynamic supercooling was less than static supercooling showing that vibration promoted nucleation. The amount of dynamic supercooling continued to decrease with increasing vibrational energy until a minimum or threshold value was reached. This minimum value of supercooling for nucleation remained constant joy all further increases in vibrational energy. For higher frequencies, similar results were observed. This behavior has been related to the necessity of cavitation for dynamic nucleation. When a liquid is cooled to a temperature below its equilibrium melting point, the solid phase is more thermodynamically stable. However, for solidification to occur, a two-step process, nucleation and subsequent growth of the solid phase, must occur. When a liquid is supercooled, that is cooled below the equilibrium melting point, the controlling process for solidification to begin is the rate of nucleation. Once nucleation has occurred, the solidification process is controlled by the rate of growth. Nucleation can be induced by two factors: either by a catalyst or by the use of mechanical shock. Numerous investigators1-4 have studied the effect of nucleation catalysis but much less systematic study has been made of nucleation by mechanical shock waves. The influence of vibrations on grain size in castings and ingots has been studied by many authors but no clear understanding of the mechanism or accurate prediction of the effect has been presented.5 It would be intuitively expected that the further the departure from equilibrium (i.e., the greater the supercooling), the easier it would be to induce nucleation. This has been quantitatively demonstrated both by walker6 and later by Stuhr,7 that the greater the degree of supercooling the easier it is to nucleate by a shock wave. Stuhr also attempted to obtain the mechanical energy required for nucleation of bismuth as a function of supercooling. He vibrated a crucible containing supercooled metal at low frequencies and various amplitudes and noted the corresponding dynamic supercooling obtained. The amount of supercooling was inversely proportional to the mechanical energy applied. Limitation of his experiment was the problem of the confinement of the liquid in the crucible without splashing and minimizing other unwanted modes of vibration. Tiller et al.8,9 did similar work on tin and Sn-Pb alloys using an electromagnetic stirring device. Their conclusions were that the magnitude of the magnetic field strength did not affect the amount of undercooling at which nucleation was initiated. While conclusive experimental results have been lacking to explain this effect of mechanical vibration on inducing nucleation, a number of theories have been proposed. Two of these theories are discussed below. 1) The Change in Melting:- Point Locally Due to the Change in Pressure (Clapeyron Equation). According to Vonnegut10 the most plausible explanation for the nucleation of a supercooled melt by cavitation is the effect of changing the melting point by a change in pressure. For materials where the volume decreases on solidification, an increase in pressure raises the melting point; for materials which expand on solidification, the melting point is raised for a decrease in pressure, i.e., rarefaction. Using the Clapeyron equation, the melting point of a metal can be calculated as a function of pressure. If it is assumed that the equation can also be used to calculate the temperature of nucleation of a supercooled melt as a function of pressure (i.e., the temperature of heterogeneous nucleation will increase with pressure at the same rate as the melting point), the amount of supercooling required for nucleation will be constant at all pressures as shown in Fig. 1. It is obvious that an isothermal change which results in an increase in melting point results in an equal increase in supercooling. This increase in supercooling may now be sufficient for nucleation. A pressure of 80,000 atm was calculated, using the Clapeyron equation, as the pressure required to increase the temperature of nucleation of nickel by 200°C. According to Lord Rayleigh,11 this very large pressure could be generated for a very brief period of time by the collapse of a cavity. This pressure wave is radiated in all directions from the collapsed cavity. If the temperature of the melt is slightly below its equilibrium melting temperature at atmospheric pressure, stable growth can follow; that is, once nucleation occurs, growth becomes the main driving force of the solidification process. This proposal has been extended to water which expands on freezing by assuming that nucleation occurs during rarefaction following the pressure pulse. This negative pressure pulse should follow immediately after the positive pressure pulse with its magnitude approaching the critical tensile strength of the liquid. The negative pressure developed during this period would raise the melting point of water and thus promote nucleation. Hunt and jackson12 have suggested this for water. Similarly, it could be postulated that bismuth which also expands on freezing could be nucleated during the negative pressure pulse. 2) Nucleation by a High-pressure Phase. An extension of the Clapeyron equation to systems where density decreased on freezing at atmosphere pressure has been proposed by Hickling.13 The phase diagram for water initially shows the well-known decrease in

Jan 1, 1969

By G. R. Leverant, C. P. Sullivan

Re crystallized TD-nickel mi-2Th0,) in both coated und uncoated conditions was fatigued at 1800°F at total strain ranges varying .from 0.2 to 0.75 pct. The fatigue life of uncoated inaferal, Nf, was related to the total strain range, ?eT, by (2Nf/021AeT = 0.014. A duplex Al-Cr pack coating increased the fatigue life by about a factor of two. The cracks that led to failure in both coated and uncoated material were initiated at the outer surface, indicating that the mechanical properties of the surface layers were important in determining fatigue life. Crack propagation and subsurface crack initiation in the TD-nickel occurred preferentially at grain boundaries with cavitation at thoria particle-matrix interfaces an integral part of the grain boundary fracture process. The importance of both the grain morphology developed during thermome chanical processing of TD-nickel and the distribution of thoria particle sizes to fatigue resistance are discussed. THE fatigue properties of only a few dispersion-strengthened metals have been studied at temperatures 0.5 Tm;1,2 among these have been lead and aluminum containing oxide dispersions. TD-nickel is a material of interest for application in aircraft gas turbine engines, but little fundamental information is available on its behavior under cyclic loading conditions. In this study, the low-cycle fatigue properties of TD-nickel were determined at 1800°F with emphasis on the 101-lowing; 1) the relation of the grain morphology produced during thermomechanical processing to crack initiation and propagation; 2) the role of thoria parti-cles in the fracture process; and 3) the effect of an oxidation resistant coating on fatigue life. I) MATERIAL AND EXPERIMENTAL PROCEDURE The TD-nickel was supplied by DuPont as a 5/8-in. thick plate which had been subjected to a proprietary series of thermomechanical treatments with a final anneal at 2000°F for 1 hr in hydrogen. The composition of the material is given in Table I. At the test temperature of 1800°F, the 0.2 pct offset yield stress was 15,000 psi, and the elongation and reduction in area were 4.6 and 3.0 pct, respectively. The microstructure of this material has been previously described.&apos; Briefly, it consists of an array of lath-shaped grains, about 0.15 mm in thickness, with the long dimension of each grain parallel to the primary working direction, Fig. 1(a). The presence of very small annealing twirls, Fig. l(b ), together with the absence of extensive dislocation networks, Fig. L/C), indicated that the material was in the recrystal- Table I. Composition of TD-Nickel ThO2 2.3 vol pct C 0.0073 wt pct lex 0.01 wt pct Cr 0.01 wt pct Cu 0.004 wt pct S 0.001 wt pct Ti <0.001 wt pct Co <0.01 wt pct Ni bal lized condition. Commercial TD-nickel sheet has a similar grain size and shape, but unlike the present material is not recrystallized as evidenced by the absence of annealing twins and the presence of a well-developed dislocation substructure.4 The plate material had Young&apos;s moduli in the rolling direction of 22 x 106 psi and 13 x 106 psi at room temperature and 1800°F, respectively, indicating a texture with a strong {100}<001> component in agreement with previous observations on recrystallized TD-nickel sheet.596 The 2.3 vol pct of thoria particles were uniformly distributed although some clustering and stringering of larger particles was occasionally seen. The average diameter of the particles was 450 and the calculated mean planar center-to-center spacing was 2100Å. Two specimens were coated with a duplex A1-Cr pack coating. The coating was somewhat nonuniform from one position to another along the gage length. An area of the coating after testing is shown in Fig. 2. Electron microprobe analysis revealed the following zones in the various lettered regions indicated in Fig. 2: A) a bcc matrix of B-NiA1 with some chromium in solid solution along with a fine dispersion of a chromium-rich second phase which was probably precipitated during cooling from the test temperature to room temperature; B) fcc y&apos;-Ni,Al with some chromium in solid solution; C) porosity; D) a two-phase mixture of a chromium-rich solid solution containing nickel and aluminum and a small volume fraction of a nickel-rich solid solution having approximately the same composition as the immediately adjacent portion of region E, E) the TD-nickel substrate containing chromium in solid solution to a depth of 5 to 10 mils. As expected from the nature of the diffusion processes involved,7 the thoria particles were present only up to the layer of porosity, region C, Fig. 2. The measured thickness of the coating proper, zones A to D, after testing was 1 to 2 mils. The specimen design and testing techniques have been previously discussed.&apos; Stressing was axial and parallel to the lath-shaped grains (i.e., parallel to the rolling direction). The total strain range was controlled between zero and a maximum tensile strain varying from 0.2 to 0.75 pct. (The test at 0.2 pct total strain range was switched to load control at 1030 cycles at which point the peak tensile and compres-

Jan 1, 1970

By L. R. Shoenberger

Boron has been used to produce nonaging low-carbon sheet steel. Retention of the necessary minimum amount of about 0.006 pet partially killed the steel. Amounts exceeding about 0.012 pet increased the degree of deoxidotion, piping tendencies, and possibility of hot tearing in primary rolling. Semikilled practice resulted in good ingot yields and satisfactory surface quality. Aluminum added with the boron provided a protective de-oxidizer. Good drawobility was indicated by performances of the steel in a limited number of deep-drawing trials. Some problems with hot-tearing and boron-analysis procedures were overcome. Metal lographically, the boron semikilled steels revealed some structures not usually found in plain low-carbon steels. IN 1943 Low and Gensamer1 reported that strain aging, which hardens and embrittles ordinary low-carbon rimmed steel, was due to nitrogen and carbon, and that oxygen played a relatively unimportant role. Since then, many investigators have substantiated their findings and indicated that nitrogen is particularly potent. Commercially, today&apos;s most widely produced non-aging sheet steels for deep drawing are either aluminum killed or vanadium rimmed types. The difference in deoxidation practice, alone, is evidence that oxygen is apparently not an important consideration in control of strain aging. The fact that nitrogen is important is apparent in the consideration that has been given, knowingly or unknowingly, to the amount combined with aluminum and vanadium. Patents were granted to Hayes and Griffis2 for the processing of aluminum-killed steel, and to Epstein" for the manufacture of vanadium rimmed material. Certain prescribed steps in producing these steels can be correlated with the formation of the respective nitrides within certain temperature ranges below the usual hot-finishing temperatures. The potential nonaging properties of either type can be reduced or suppressed by cooling too rapidly to permit the aluminum or vanadium to combine with nitrogen. Subsequent suberitical annealing of the cold-rolled strip, however, normally forms the nitrides and produces the resistance to strain aging. Titanium-killed nonaging steel, described by Comstock,1 forms a nitride in the molten state and is essentially nonaging throughout its processing. Zirconium-killed steel, which was investigated briefly by the author,* appeared to have similar nitride- forming characteristics. It is known" that chromium can produce nonaging rimmed steel, but relatively little is known of the potentialities of some of the other nitride-forming elements such as boron, silicon, columbium, and cerium. In attempting to develop a new nonaging cold-rolled sheet steel with good drawability, the following factors were considered pertinent. Such a steel would necessarily have a low carbon content and therefore have a relatively high degree of oxidation when made in a basic open-hearth furnace. If the denitriding element were also a deoxidizer, a part of the addition would be lost as oxide. The degree of deoxidation would determine whether the steel is rimmed, semikilled or killed, and also could be expected to have an important bearing on ingot yields and ultimate surface quality. Assuming that the pattern for the production of cold-rolled sheets would not be changed to any great extent, the nitride must form in the molten steel, in hot rolling, in subsequent cooling, or in annealing. The nitride, once formed, should resist dissociation and be stable in the final product. Usually an excess of the nitride-forming element is required to combine with sufficient nitrogen. If the element used is a strong ferrite strengthener, a small excess may markedly decrease drawability. With aluminum and vanadium, about 0.03 to 0.05 pct in the steel is preferred. Epstein has said" that about 0.30 pct chromium is required. Titanium nonaging steels are hard unless a sufficient amount (about 0.30 pct) is added also to combine with the carbon. The cost of the necessary amounts of these latter two elements discourages commercial acceptance. Silicon was considered as a possible nitride former, but since amounts up to 0.10 pct in rimmed and semikilled steels do not induce marked resistance to strain aging, larger amounts are apparently required, which would tend to harden and strengthen the ferrite. Of the other elements mentioned, all but boron are expensive heavy-metal elements. Stoichi-ometrically, almost an equal weight of boron would be required to combine with the nitrogen—-ordinarily about 0.003 to 0.006 pct in scrap-practice open-hearth steels. Boron is a slightly stronger deoxidizer than carbon but is less powerful than zirconium, aluminum, or titanium. Thus a rimmed-steel practice might be possible. There is much in the technical literature concerning the hardenability effects of minute amounts of boron in killed steels but very little about its behavior in low-carbon material—particularly as a ferrite strengthener. The available data indicated a need for better information concerning the effects of boron in low-carbon strip steels. Experimental Work Development of a Boron-Treated Nonaging Strip Steel—Initial attempts to produce a boron-rimmed strip steel employed 3-ton basic open-hearth heats which could be teemed into molds large enough to sustain a normal rimming action. Boron as ferro-boron was added to the ladle in small amounts because of the reported hot-short character of aluminum-killed heat-treating grades containing more than about 0.005 pct boron. Actually, the amounts used, i.e., 1/8 and 1/4 lb per ton, would be large for

Jan 1, 1959

By William E. Hughes, Roderick K. Davey

The objective of this chapter is to review and discuss interpolation techniques commonly in use in the mining Industry today, including simple examples. This chapter will not attempt to compare the relative accuracy of each technique as this subject has adequately been covered by several authors (Knudsen and Kim, 1967; David, 1974; and Barnes, 1979) When appropriate, methods will be compared relative to the results of simple examples and computational ease. The examples presented are based on metallic deposits. The techniques, however, are not restricted to metallic deposits and can generally be applied to nonmetallic ones. The purpose of interpolation, as applied to a mineralized deposit, 1s to extend the knowledge of the grade and geology of localized samples to an estimate of the grade and mineralogy of a larger block of ground or even an entire deposit. The word interpolation means to compute values between given values and is limited to that region between the known values. The distinction between interpolation and extrapolation is important and must be adhered to in the application of these techniques in general, the interpolation must be limited to the area enclosed by verified samples. The methods being discussed can be broadly broken into three categories. ( 1 ) geometrical methods, (2) distance weighting methods, and (3) geostatistical techniques.

Jan 1, 1979

By J. B. Urnfileb

THE function of gas in the development and production of oil has far reaching consequences that should be emphasized. The technical aspects of the subject have recently had a great deal of attention but less thought has been given to fundamental concepts underlying oil and gas law and the many customs and practices that have grown up in the industry. I shall re- view briefly the advance in knowledge of the subject and attempt to relate these concepts to legislative, judicial and operating problems. Early writers on oil and gas in Pennsylvania noted their close association in oil pools and their contemporaneous decline in output; also, that as gas pressure decreases so does production, that new offset wells reduce the output of existing wells, and even that tubing a well lengthens its flowing life. Expanding gas was deduced as the principal expulsive force. These fundamental observations had been made at least as early as 1880.l They were treated, however, as academic considerations and did not greatly influence law or practice for many years except to instil into all operators an urgent desire to hasten offset drilling to obtain as much of the flush as possible.

Jan 1, 1932

By FREDERICK W. BRADLEY

MINING methods are evolved rather than devised; and the process is slow. The advance in no particular year is phenomenal, but progress is un- questionably being made constantly in several directions: (a) better adaptation to given conditions of various "systems" of mining; (b) better utilization of mechanical equipment ; (c) improvement in working conditions so as to promote the health, safety and efficiency of the workers. During the year 1930 operations were commenced at a number of important new mines. Methods adopted are not new, except in minor detail, but the fitting of methods to conditions is interesting, because, as the engineers presumably started from scratch, they have selected the methods that experience under similar conditions has indicated as being the best.

Jan 1, 1931

By Albert L. Toenges

Alaska requires an adequate fuel supply for its development, and has large potential coal reserves ranging from lignite to subbituminous and anthracite. Coal production in the Territory now is less than the requirements. In 1947, production was 361,000 tons, divided about equally between bituminous coal from the Matanuska field and subbituminous coal from the Nenana field. There is need for development of modern mechanized mines, which should produce the required output with a minimum of workers. These mines should not be thought of in the light of large potential capacity, as in the States. However, these new mines should be developed by modern methods, which should result in lower costs than at present. Because of the diverse physical conditions in the coal fields, intensive investigation by diamond drilling is necessary to properly plan the development and equipment of mine sites at minimum cost. The Bureau of Mines is doing this now in the Wishbone Hill area of the Matanuska field. All coal land in Alaska is government-owned and subject to the Coal Leasing Act.

Jan 1, 1949

By D. C. Hilty, W. Crafts

L. S. Darken—Laboratory investigation of deoxidizing and other steelmaking reactions is usually centered, at least first, on the determination of the equilibrium or equilibria involved. This seems a reasonable procedure since equilibrium, if attained, depends only on composition, temperature, and pressure; hence conclusions derived from data on small experimental quantities are applicable to a heat of steel providing eauilibrium is attained in both cases. A knowledge of equilibrium serves as a useful framework even though we may know that practical conditions do not correspond to complete equilibrium. On the other hand, nonequilibrium or rate phenomena depend on a wider variety of conditions and are more difficult to interpret; conclusions applicable to laboratory conditions may or may not apply to larger scale phenomena. Hence the attainment or nonattainment of true equilibrium in the experiments here reported is of critical importance in evaluating their significance. Since some of the statements in this paper and in the closely related preceding one (on aluminum deoxidation) imply some doubt on this matter, I should first like to ask the authors whether their conditions are intended and believed to represent equilibrium. I should like to point out three considerations which seem to cast considerable doubt on the achievement of equilibrium, at least of the particular equilibrium under consideration. 1. In the experiments on manganese deoxidation the authors point out that they could not maintain the manganese-oxide slag on top of the metal in their rotating crucible, and hence they substantially dispensed with this slag. This leads to serious trouble in the interpretation of the results, for any equilibrium is, of course, a particular specific equilibrium—in this case Mn + O = MnO The experimental deletion of the upper layer of manganese oxide means that if equilibrium is attained at all it is attained between the metal and the MnO which has soaked into or adhered to the crucible (under the metal) and has dissolved substantial amounts of the crucible material including impurities. These impurities may constitute a significant portion of the slag by virtue of the small total amount of slag, even though the crucible is relatively pure. Hence there would seem to be a strong presumption that the equilibrium (if attained) involves not a pure MnO (or MnO — FeO) slag but one saturated with alumina and containing perhaps considerable impurities which substantially lower the concentration and activity of MnO, causing the above reaction to proceed to the right further than it would in the absence of alumina and impurities. Hence it is not surprising that manganese here appears as a better deoxidizer than found by other investigators. The present results may represent equilibrium with a slag of unknown composition which seems unlikely to be particularly related to plant experience. 2. The curves representing the observed silicon deoxidation (figs. 3, 4, and 5) are all drawn with a discontinuity in slope at about 0.02 pct oxygen. This point is interpreted as corresponding to the three-phase equilibrium, metal, slag, solid silica. The type of construction shown in these figures (though apparently fitting the data) is contrary to a fundamental principle of heterogeneous equilibrium as pertains to the construction of phase diagrams. According to this principle, the two solubility curves (each of the two portions of the curves in figs. 3, 4, and 5) must intersect in such manner that their (metastable) extensions must lie outside the homogeneous field rather than inside as in these figures. In other words, the "point" in these curves should be aimed in the opposite direction, if it is to be interpreted as corresponding to the three-phase equilibrium. The construction adopted is in violation of the second law of thermodynamics. This matter is discussed in detail in several texts and also by Lipson and Wilson.&apos;" The same criticism applies to the later figures representing conditions for manganese additions. The occurrence of this discontinuity or break at 0.02 pct oxygen casts further doubt on its interpretation. The earlier investigation of this system by Korber and Oelsen is in substantial agreement with the several recent findings of Chipman and coworkers that the oxygen content of iron in equilibrium with silica and silica-saturated iron oxide slag is about one third to one half that (0.24 pct at 1600") of iron saturated with pure iron oxide; thus there seems reliable evidence that iron saturated with silica and iron silicate slag at 1600" contains about 0.1 pct oxygen, or certainly much more than the 0.02 pct proposed in this paper. 3. In the quarternary system iron-silicon-manganese-oxygen one of the equilibria involved may be written 2 Mn + SiO2 (solid) = 2 MnO <slag> + Si The activity of SiO, is constant (if equilibrium is attained) by virtue of its presence as a substantially pure solid. At not too low metallic manganese content, the activity of MnO in the slag is constant by virtue of the fact that the slag is substantially pure manganese silicate saturated with silica and hence of constant composition. Thus the equilibrium constant for the above reaction is asi/a2Mn. Barring unanticipated large changes in the activity coefficients, the equilibrium constant may be adequately approximated for the composition range covered as [% Si]/[% Mn]2. Thus a plot of log [% Mn] against log [% Si] would be expected to be linear with a slope of one half as found by Kijrber and Oelsen. In the present investigation the slope (shown in fig. 15) is found to be one. It is difficult to believe that this finding represents a correct equilibrium determination, since it is at odds both with prior experimental investigation and with. theory. In view of the above points it seems that, although this paper reports many interesting findings, there is room for considerable skepticism as to the attainment of equilibrium and as to the conclusions drawn. N. A. Gokcen—The authors consider that Si% x O2% product is constant. This product is a function of the asi X a0 activity of Si02. The true constant is -------------. If the asio2 slags of this investigation were always saturated with SiO2 then Si% X O2% product would be constant,

Jan 1, 1951

By Hobart M. Kraner

THE mineralogy of blast furnace sinter is of interest because its mineral content is one of the important factors contributing to its character. There are so many other factors affecting the properties of the sinter, however, that it is well to mention them here. The proportion and character of the raw materials, that is, raw ores, concentrates, returns, and fuel, as well as the mixing and the water content, all have a marked effect on the physical properties of the product and the degree to which sintering action can be carried on. The process of sintering is a relatively fast operation. In as much as appreciable time is required to carry on processes of fusion in such masses of low thermal conductivity, large lumps of hematite ore frequently remain unfused and partly unchanged in state of oxidation in the sintering process. The kind, the grain size, and the amount of fuel used affect both the completeness of the fluxing reaction and the prevailing atmosphere. The rate of reduction in laboratory tests is not only dependent upon the state of oxidation of the sinter but also upon the sizing and porosity. Atmosphere and temperature affect the state of oxidation of the iron oxide, and the atmosphere alone may determine the ferrous minerals that finally develop. The rate and extent of cooling, the type of coolant, the subsequent handling, and screening all have serious effects upon the type of sinter that eventually enters blast furnace bins. The degree to which actual fusion or fluxing takes place in the sintering operation has a marked effect upon density. A sinter which has been extensively fused by high content of fuel in the batch will no doubt have a higher weight on the bulk basis than one which had a lower fuel content. As high temperatures are required to do this job, the iron oxide under these conditions will be largely magnetite. Sintering at low temperatures to produce larger proportions of hematite means a decrease in the amount of liquid formed and a much more sensitive bonding process. In this case the liquid must be distributed more uniformly and thereby used more efficiently than would be the case where higher temperatures were permitted to prevail more or less indiscriminately. Where coarse ore particles are used in a sinter mix it is not expected that any particles coarser than 1/4-in. can be fused and incorporated in the system to such an extent that the gangue contained within these lumps will have been converted or fused by the sintering process. It is for this reason that coarse ore, returns, or both, in a sinter usually result in a sinter which breaks easily and at the same time may contain some of the original minerals of the lump, such as quartz and hematite. In examination of sinters at Bethlehem Steel Co. minerals such as quartz and corundum have been found, none of which are considered normal associ- ates of wustite or magnetite. Some degree of heterogeneity or lack of equilibrium is not unusual in the sintering process. The differences in specific gravity between hematite and magnetite might be ample reason for poor strength in a not very well sintered mass containing coarse particles of. ore or returns. The shrinkage taking place in a lump of hematite in its conversion to magnetite by temperature and/or atmosphere is appreciable. Sintering of ores as it is carried out is crude chemistry, for the grain size is relatively coarse, the application of heat is certainly not uniform, and the time factor is inadequate for other than partial completion of reactions. Coarse lumps of coke or coal cause local heating around these centers, and fuel which is too fine may result in such slow burning that sufficiently high temperatures are not always obtained. High temperatures are essential to the work required. The Swedish practice of sintering is established on the basis of producing an easily reducible product high in hematite. This is achieved through uniformity of grain size in the sinter mix and close control of the temperature through careful regulation of fuel and sintering rates. This produces a sinter which is very tough in character and which has a high degree of porosity. Although the hematite content is not produced upon cooling by drawing air through the mass, there would be greater possibility of accomplishing this reaction with this type of sinter than is the case in American practice. In the latter, the temperatures are so high that temperature alone converts most of the mass to magnetite. The grains are so coarse in the final product that together with the fluxed condition it would be difficult to reoxidize them to hematite upon cooling. An examination of the iron-oxygen diagram&apos; shows that hematite does not exist above 2651°F. It also shows that there is no liquid in the pure magnetite-hematite system until 2881°F is reached. On the other hand, in the system magnetite-wustite liquids exist at considerably lower temperatures than this. It will be seen, therefore, considering only the iron oxides, that the bonding action obtained in America in sinters comes about through considerable temperature and/or reducing conditions that produce compositions containing even less oxygen than is contained in magnetite or than results from the fusion of silicates. The bonding obtained from the iron oxides is encouraged by the reducing conditions that prevail in the vicinity of the fuel particles in a mass of this sort, where temperatures are above 2600°F. As magnetite and wustite are opaque, they do not lend themselves to petrographic study by transmitted polarized light. The silicates found in sinter and the glass that has not crystallized transmit light and can be studied by these methods in which indices of refraction and other optical properties of anisotropic crystals lead to their definite identification. The index of refraction is the only property that can be measured in glass under the microscope, and this is a clue to its probable approximate composition.

Jan 1, 1954

By R. C. Ferguson, Harlowe Hardinge

Oscar Johnson—In my opinion, the effect of mill speeds on grinding costs must be studied along with capital investment and dollars gathered together as profits. Comparing the entire groups of operators with those who have had the opportunity to make slow-speed mill studies, I think you will find the latter small in numbers. Most managers want the equipment worked to its maximum output. There are, however, some installations where plant and mill sizes are such that they can do the job with reduction of mill barrel speeds. The past and the present installations of the industry are laid out to get the most capacity for the least capital outlay. This is the case even with the plants of Chile Exploration, International Nickel, Morocco, and Anaconda, now under construction or being changed. The industry recognizes that most all equipment it buys today is good and can be depended upon for efficient performance. Under this scheme of things, I am doubtful that slow-speed ball mill operation will be generally applicable. With reference to the U. S. Bureau of Mines laboratory tests, I think table II could have been omitted. It is inconclusive as to maximum efficiency for the low-pulp level mill on hard ore. There should be no question about this point. However, data on mill speeds can be found to substantiate various theories as well as refute them. Gow, Guggenheim, Campbell and Coghill, in their paper on Ball Milling,&apos; believe their 2 x 2 ft laboratory mill reflects results that can be expected from large mills. If so, then referring to their table 11, they state, "The conclusion to be drawn from this second series is that high speed, not exceeding 72 pct of the critical, favors capacity, as before, but that with proper conditions of operation high speeds may give as good efficiency values as low speeds. In this case the efficiency values are nearly constant. A horizontal curve would indicate that the amount of grinding was directly proportional to the power expended, and these tests suggest that such a coildition can be made to exist in commercial operations." Table II (From Paper by Gow et a1)2 Speed. Pot Critical 32 42 52 62 72 82 Capacity: Surface tons per hr (65- mesh) 266 42.1 54.4 65.9 74.3 74.1 Surface tons per hr (200- mesh) 56.1 87.4 112.7 137.1 154.2 153.0 Efficiency: Surface tons per net hp hr (65-mesh) 35.7 36.3 36.3 35.4 34.3 32.3 Surface tons per net hp hr (200-mesh) 75.3 75.3 75.1 73.7 71.0 66.0 Ore in mill, 1.b. 98 100 100 113 122 165 The field performance data, table 111, represents much effort in its collection and preparation. But, one must realize that there are many variables that effect the efficiency of grinding mill operation, and too much must not be assumed as to the effect of some specific change. Possibly with changes in mill speed, the results might be more consistent by also a change in ball rationing, type of ball, volume of ball charge,. p.ulp level and amount of pulp in the mill, pulp consisting, design of liner, circulating load, etc. Also, changes in ore character must be reckoned with when evaluating grinding performance. At present the Climax Molybdenum Corp. is running at much reduced capacity. Mr. James Duggan informs me that at mill speeds of 17 rpm, they save a $0.025 per ton on liners and $0.025 per ton in power, but, if the demand for molybdenum increased, he would go back to higher speed to obtain maximum tonnage, as the values from the increased tonnage would far more than offset the one half saving at the slower speed. The Jnspiration ran a six months&apos; test between mills running 21 rpm and 23.5 rpm. The slower mills ground 10 pct less ore with a slight saving per ton, but when the reduced plant tonnage was checked back into the actual cost figures of concentration, the high-speed mills with their greater tonnage showed considerable advantage. To be convinced of possible practical results from the predictions in the conclusions, I think we would have to rely on the analysis of expert cost accountants to furnish the necessary proof figures. Hardinge and Ferguson are to be commended for the work in preparing this paper. I am convinced that our Massco engineers should go into higher speeds with our equipment. Harlowe Hardinge (authors&apos; reply)—For one, I heartily agree with Mr. Johnson&apos;s opening statement that the effect of mill speeds on grinding costs must be studied along with capital investment and dollars gathered together as profits. It was on this basis and for this reason the paper was written. Mr. Johnson, on the other hand, takes the position that, on the whole, low speeds are not justified from the economic standpoint, basing his principal reason on the fact that lower mill speeds cut mill capacities and hence reduce the gross income from the product produced. There is no denying this point. It is almost axiomatic. It is for this very reason that the overall advantage of lower mill speeds has been discounted and even overlooked. It was for this reason mainly that the paper was written in the first place. It is one thing to plan an efficient operation at the outset, basing one&apos;s figures on the tonnage requirements at the time, and it is quite another to be confronted with the problem of increasing the output of an existing installation at a minimum of capital expenditure. Economic consideration of a new installation is greatly influenced by referring to an old one. Too often, the analyst assumes that if this practice is followed in the new installation, one would not go wrong. It is just here that he may be wrong. Past practice and low capital expenditure are all too frequently given priority over the engineer&apos;s analysis of operating costs. When we are able to start fresh, we should give proper weight to other economic factors which do not exist in an old installation. It is these economic factors that make it possible to spend at the outset just a little more money and get it back in a matter of months and effect big savings for years to come. F. C. Bond—This paper is of considerable importance in that it emphasizes a modern trend to operate ball mills at somewhat slower speeds than formerly. We have checked the data in the paper with that obtained

Jan 1, 1951

By Harlowe Hardinge, R. C. Ferguson

Oscar Johnson—In my opinion, the effect of mill speeds on grinding costs must be studied along with capital investment and dollars gathered together as profits. Comparing the entire groups of operators with those who have had the opportunity to make slow-speed mill studies, I think you will find the latter small in numbers. Most managers want the equipment worked to its maximum output. There are, however, some installations where plant and mill sizes are such that they can do the job with reduction of mill barrel speeds. The past and the present installations of the industry are laid out to get the most capacity for the least capital outlay. This is the case even with the plants of Chile Exploration, International Nickel, Morocco, and Anaconda, now under construction or being changed. The industry recognizes that most all equipment it buys today is good and can be depended upon for efficient performance. Under this scheme of things, I am doubtful that slow-speed ball mill operation will be generally applicable. With reference to the U. S. Bureau of Mines laboratory tests, I think table II could have been omitted. It is inconclusive as to maximum efficiency for the low-pulp level mill on hard ore. There should be no question about this point. However, data on mill speeds can be found to substantiate various theories as well as refute them. Gow, Guggenheim, Campbell and Coghill, in their paper on Ball Milling,&apos; believe their 2 x 2 ft laboratory mill reflects results that can be expected from large mills. If so, then referring to their table 11, they state, "The conclusion to be drawn from this second series is that high speed, not exceeding 72 pct of the critical, favors capacity, as before, but that with proper conditions of operation high speeds may give as good efficiency values as low speeds. In this case the efficiency values are nearly constant. A horizontal curve would indicate that the amount of grinding was directly proportional to the power expended, and these tests suggest that such a coildition can be made to exist in commercial operations." Table II (From Paper by Gow et a1)2 Speed. Pot Critical 32 42 52 62 72 82 Capacity: Surface tons per hr (65- mesh) 266 42.1 54.4 65.9 74.3 74.1 Surface tons per hr (200- mesh) 56.1 87.4 112.7 137.1 154.2 153.0 Efficiency: Surface tons per net hp hr (65-mesh) 35.7 36.3 36.3 35.4 34.3 32.3 Surface tons per net hp hr (200-mesh) 75.3 75.3 75.1 73.7 71.0 66.0 Ore in mill, 1.b. 98 100 100 113 122 165 The field performance data, table 111, represents much effort in its collection and preparation. But, one must realize that there are many variables that effect the efficiency of grinding mill operation, and too much must not be assumed as to the effect of some specific change. Possibly with changes in mill speed, the results might be more consistent by also a change in ball rationing, type of ball, volume of ball charge,. p.ulp level and amount of pulp in the mill, pulp consisting, design of liner, circulating load, etc. Also, changes in ore character must be reckoned with when evaluating grinding performance. At present the Climax Molybdenum Corp. is running at much reduced capacity. Mr. James Duggan informs me that at mill speeds of 17 rpm, they save a $0.025 per ton on liners and $0.025 per ton in power, but, if the demand for molybdenum increased, he would go back to higher speed to obtain maximum tonnage, as the values from the increased tonnage would far more than offset the one half saving at the slower speed. The Jnspiration ran a six months&apos; test between mills running 21 rpm and 23.5 rpm. The slower mills ground 10 pct less ore with a slight saving per ton, but when the reduced plant tonnage was checked back into the actual cost figures of concentration, the high-speed mills with their greater tonnage showed considerable advantage. To be convinced of possible practical results from the predictions in the conclusions, I think we would have to rely on the analysis of expert cost accountants to furnish the necessary proof figures. Hardinge and Ferguson are to be commended for the work in preparing this paper. I am convinced that our Massco engineers should go into higher speeds with our equipment. Harlowe Hardinge (authors&apos; reply)—For one, I heartily agree with Mr. Johnson&apos;s opening statement that the effect of mill speeds on grinding costs must be studied along with capital investment and dollars gathered together as profits. It was on this basis and for this reason the paper was written. Mr. Johnson, on the other hand, takes the position that, on the whole, low speeds are not justified from the economic standpoint, basing his principal reason on the fact that lower mill speeds cut mill capacities and hence reduce the gross income from the product produced. There is no denying this point. It is almost axiomatic. It is for this very reason that the overall advantage of lower mill speeds has been discounted and even overlooked. It was for this reason mainly that the paper was written in the first place. It is one thing to plan an efficient operation at the outset, basing one&apos;s figures on the tonnage requirements at the time, and it is quite another to be confronted with the problem of increasing the output of an existing installation at a minimum of capital expenditure. Economic consideration of a new installation is greatly influenced by referring to an old one. Too often, the analyst assumes that if this practice is followed in the new installation, one would not go wrong. It is just here that he may be wrong. Past practice and low capital expenditure are all too frequently given priority over the engineer&apos;s analysis of operating costs. When we are able to start fresh, we should give proper weight to other economic factors which do not exist in an old installation. It is these economic factors that make it possible to spend at the outset just a little more money and get it back in a matter of months and effect big savings for years to come. F. C. Bond—This paper is of considerable importance in that it emphasizes a modern trend to operate ball mills at somewhat slower speeds than formerly. We have checked the data in the paper with that obtained

Jan 1, 1951

By Albert F. J. Bordeaux

INTRODUCTION. THE following general survey of the character and present condition of the silver-mines of Mexico, though not offered as a detailed treatise, has been prepared with care, is believed to he generally up-to-date, and is offered as a summary which may be found useful by mining engineers. Mexico has ranked for several centuries first among the silver-producing countries. It is now second as copper-producer, and seventh as gold-producer, with a fast-increasing output every year. The total amount of capital invested in its mining- and smelting-works is more than $250,000,000, while the yearly metallic production is $160,000,000. There are more than 20,000 recorded mining properties. The silver-mines of Mexico represent deposits of three principal classes: (1) veins and stock-works in eruptive rocks; (2) fissure-veins crossing the crystalline schists, granite, diorite, etc. ; and (3) veins and replacement-deposits in limestone. The true fissure-veins in some districts contain (in value) more gold than silver. In other deposits, the silver is decreasing in depth, leaving galena and zinc-blende as the principal ores.

Jan 9, 1908

By B. T. Brady

Rock mechanics, like all engineering disciplines, must have a theoretical foundation. The subject of this chapter is the formulation of analytical methods that may aid in the rational design and determination of the stability of engineering structures in competent brittle rock materials. By an engineering structure in rock, we mean any (1) excavated sub- surface opening, (2) open surface structure, or (3) system of openings in rock that is virtually self-supporting-that is, not requiring artificial systems to carry structural stresses.

Jan 1, 1970

By AIME AIME

CADWALLADER EVANS JR. has long been a leading figure in the anthracite mining industry and one of Pennsylvania&apos;s prominent citizens. He is, in fact, a native son, having been horn in Pittsburgh on Sept. 17, 1880. At Lehigh, from which he graduated in 1901 with the degree of Mechanical Engineer, Tom Girdler was a classmate, and both were active in football affairs. Going hack to Pittsburgh, he got his first job as trouble shooter for the Oliver Iron & Steel Co. A year later he entered the coal industry, getting a job with the Blaine Coal Co. as inspector of construction and later was superintendent of the Blaine mine at Elizabeth. Pa.

Jan 1, 1943