Search Documents

By Robert F. Jones

INTRODUCTION Upflow Solids Contact Clarification is a process long employed in the treatment of potable water, wastewater and municipal sewage. This process incorporated in a fiberglass conical structure seems to offer an economical solution to problems encountered in reduction of particulates in uranium effuents. CONCEPT OF UPFLOW CLARIFICATION Use of suspended solids contact units date back to the 1930's. These types of units produced by Infilco and the Permutit Company, among others, were used in the Lime-Soda softening process to precipitate calcium and magnesium salts from hard water. In general, the process operated as follows: (a) Raw water entered a central chamber where it was mixed with chemicals. The chamber had provisions for agitating and circulating the chemicals so that mixing and reaction zones were formed. (b) The water, precipitated chemicals, floc and turbidity flows to a clarification chamber (the Permutit precipitator used a truncated cone). In most cases the influent then passes upward through a blanket of suspended floc and other solids before it leaves the chamber at effluent weirs or launders.

Jan 1, 1984

By J. Finch, W. Petruk, R. G. Pinard

An investigation was conducted to determine the minimum number of samples that must be studied by image analysis of polished sections to characterize a mill product and determine the apparent mineral liberation. It was found that a representative polished section cannot be prepared from an unscreened sample that has a wide size range of particles. Similarly, individual screened fractions are not representative of the sample because minerals are partitioned during screening, and the quantities of soft brittle minerals are increased in fine grained fractions, whereas the quantities of hard minerals are increased in coarse grained fractions. It is assumed that results obtained by combining data for a series of narrow size range screened fractions (one Tyler size range) are representative of the sample, and relatively accurate apparent mineral liberation data can be obtained for a mill product by analyzing each fraction and combining the data. Somewhat less accurate data would be obtained by analyzing a series of screened fractions that have a wider size range of particles (five Tyler size ranges).

Jan 1, 1987

By Richard D. Christie, K. Jay Pillai

In the past, it was not unusual for coal preparation plants to discard fine run-of-mine coal. This practice has changed due to increasing quantities of fine material, improvements in beneficiation methods, and the need to recover revenue from these fines. It is in this context that the coal industry has increasingly been turning to froth flotation for fine coal beneficiation. Reagent schemes have been developed to promote coal flotation and to treat the resulting refuse material. While reagent technology has improved, however, most plants rely on manual control of reagent dosing and circuit operation. This often results in misuse of reagents, loss of coal recovery, and consequent loss of revenue. Fine coal circuit operations can be dramatically improved through automation. Intelligent process control systems are now in use which are capable of optimizing reagent usage, maximizing coal recovery, and minimizing chemical costs associated with refuse handling. This paper describes a type of control system currently used in preparation plants, and provides data and information on the significant improvements such systems can produce.

Jan 1, 1994

By Menzhans Guo

A coal bunker basically acts as a buffer and regulator to reduce the interruptions between its proceeding production system and succeeding haulage system so as to maximize the availability of the whole system. Although such a role has long been recognized, quantitatively studying it is still rarely seen in the literatures. Its unique characteristics, coupled with numerous transitional states, make it very complex to describe the state transitional process in analytical models and, also very difficult to seek an analytical solution. Moreover, the analytical models inappropriately consider the state of bunker being full or empty as a kind of failure, therefore, by no means can they realistically describe the impact of the difference between rates of coal flowing to and from a bunker on the system availability. In light of this, Monte Carlo simulation methods are suggested to reach an approximate solution. In comparison, simulation methods are simpler and more effective than analytical approaches. Applications of simulation methods to a Northern colliery for determining bunker size from the viewpoint of maximizing system's availability are discussed. The results are satisfactory.

Jan 1, 1992

By Paul D. Tavares, John Forbes, Eric R. Drooff

As the existing major U.S. - Canada rail tunnel was too small to accommodate double-stack container cars, Canadian National Railways is constructing a new parallel tunnel with a 50% greater diameter. Starting in Sarnia, Ontario, the new shallow-cover bored tunnel runs under a large research building and several other structures in an oil refinery before travelling under the St. Clair River. Maximum predicted settlements to be caused by the 9.2 meter diameter earth pressure balance TBM in the soft St. Clair till were in excess of 100 millimeters. As such, these settlements had the potential to cause severe damage and disruption to the existing refinery. In order to reinforce the soft clays below the refinery research building and other structures, and to compensate for settlement caused by the tunnelling, the ground improvement method of Soil Fracture grouting was successfully applied for the first time in North America. This paper will describe the details of both the soil fracture grouting application and the elaborate electrolevel remote monitoring system used.

Jan 1, 1995

By J. Derwin King, Harrison R. Cooper

Applications of nuclear magnetic resonance (NMR) offer possibilities for on-line sensing of the concentrations of several elements in flowing sample streams. In addition to hydrogen, these elements, generally of low-order atomic number, include aluminum, phosphorus, fluorine, sodium, boron, and lithium contained in minerals having commercial importance. Many such elements have been difficult or impossible to successfully measure on-line using the more familiar X-ray fluorescence and neutron activation analysis techniques. The availability of practical on-stream analysis methods is essential to applying advanced controls to processes incorporating these elements. On-stream NMR instrumentation has been demonstrated in the past for several process applications including, as an example, coal flow and analysis; and the technology has recently been extended to the measurement of phosphorous BPL in Florida beneficiation plants. The technique involves simultaneous sensing of proton (hydrogen) and 31P intensities to provide data for continuous calculation of BPL in the phosphate through calibration to volume fractions of water and solids. Initial operating results are described using the PhospholyzerTM on-stream phosphorous analyzer designed for plant application.

Jan 1, 1990

By Jeffery H. Stricklin

Jim Walter Resources operates five underground coal mines with longwall faces in operation in four of the mines. Due to high air velocities (1000-1200 fpm) needed for methane control together with the friability of the coal, dust control on JWR longwalls offers unique challenges. We have tested many innovative measures to reduce respirable dust concentrations on longwalls with varying degrees of success. These measures include the "shearer clearer" system, different drum water spray configurations, sprays on the longwall belt, stageloader and crusher sprays, wetting agents in the spray water system, and homotropal ventilation. Water infusion of deactivated horizontal methane drainage holes in longwall panels is now being evaluated. A study was completed in November 1986 where water was infused into two horizontal de-gas holes. Personal gravimetric samplers were used to measure respirable dust concentrations and showed a significant reduction in the infused zone. A more in depth study will be conducted. This paper will describe the dust control measures presently used on JWR longwalls, give the results of past studies, and discuss new methods proposed to control longwall dust.

Jan 1, 1987

By X. Wu, E. Topuz

Booster fans have been extensively used in underground mines throughout the world. In the United Kingdom, S. Africa, Germany, and other countries, many non-coal and coal mines employ booster fans. These fans help to reduce air leakage, to provide an improved flow distribution and to reduce the overall cost of mine ventilation. Although booster fans have not been used in coal mines in the United States, a recent survey indicated that many coal mines would install booster fans if they were allowed to do so. With the inclusion of coal mines, the use of booster fans in underground mines is expected to increase substantially in order to maintain air quality and quantity requirements. Several techniques are used, with varying degrees of success, in determination of booster fan locations in an underground ventilation network. These techniques include linear programming, critical-path crashing, CPM together with cutset operations, the out-of-kilter method, and simulation techniques. This paper provides a brief comparison of these techniques, and reports on ongoing research for an improved methodology for the determination of booster fan locations.

Jan 1, 1987

By Satya Harpalani, Xue Zhao

This paper discusses the results of an experimental investigation to study the release of methane in coalbeds. Absolute porosity of coal samples was first determined experimentally. Following the porosity measurement, adsorption/ desorption tests were carried out to determine the gas content of coal and the rate at which it is released. Finally, micrographs were obtained using electron microscopy and the use of a physical model, developed to explain the gas flow behavior of coal, was justified. The results of this study indicated that the measured absolute porosity of the coal sample was between 5 an 6%. This was significantly lower than the porosity estimated by comparing the micrograph area occupied by the pores and the area of observation for several micrographs, suggesting that coal has a large number of pores with a very small volume. The micrographs also clearly indicated that coal has a large interconnected network of cleats and microfractures. The adsorption/desorption experiments showed a hysteresis between the adsorption and desorption isotherms. Also, the rate of desorption was found to be strongly dependent on the particle size of the specimen.

Jan 1, 1989

By Jim Oehler

The US minerals industry, as well we know, has been hit hard by the recent recession and is faced with what is projected to be a slow recovery. Even so, there was an underlying feeling of optimism at American Mining Congress' International Mining Show in Las Vegas, NV, Oct 11-14. More than 25,000 people attended during a particularly rough financial year, dispelling fears that attendance would dip sharply below 1978's 30,000 plus tally. The equipment expositionheld every four years-was the largest show of its kind this year in the Western Hemisphere in terms of exhibit space, providing an extensive view of mining-related equipment. In addition to the nearly 700 exhibits occupying more than 445 hm2 (11 acres), 20 technical sessions were held covering topics ranging from minerals availability and the state of the mining industries to communications, computers, and accounting. Government officials were well represented, with six US senators and five US representatives participating in various convention functions. Sen. Paul Laxalt (R-NV) was the keynote speaker at the welcoming luncheon. Other senators involved in the show included Howard W. Cannon (D-NV), Pete V. Domenici (R-NM), James A. McClure (R-ID), Frank H. Murkowski (R-AK), and Steven D. Symms (R-ID). Representatives on the program were Joseph M. Gaydos (D-PA), Guy Vander Jagt (R-MI), Don Young (R-AK), Jim Santini (D-NV), and Ceil Heftel (D-HI). There were also many international vistors at the show, including exhibitors from Australia, Austria, Canada, England, Finland, Sweden, South Africa, and West Germany. Equipment Highlights Equipment and services featured at the exposition ranged from aerial mapping to wire rope. Aisle space alone between exhibits exceeded 8 km (5 miles). And the companies represented ranged from small businesses to large corporations. Some of the company products described here are representative of the many exhibitors in attendance. Atlas Copco's extensive display of rock drilling and tunnel and shaft boring equipment featured its Boomer H-201, the newest addition to its line of underground drifting rigs; the ROC 306, a new track-mounted, high pressure down-the-hole drill rig; a new hydraulic surface crawler drill, the ROC 712H, designed for small and medium-size holes in quarries and small open-pit mines; a computerized analysis system, CARE (see page 1570), designed to project productivity and operating costs for various mining operations; several electro-hydraulic loaders, including the new rail bound LM E60 and LM E80, and two Hagg-loaders-the 7HR and 10HR-that use two digging arms to rake and guide muck; a mechanized blasthole charging system; rock bolting equipment and its new Swellex roof bolting method; Sandvik Coromant drill steel and bits; and its new Jarva R200 raise boring machine.

Jan 11, 1982

By Carrie Smith

This fall, the Society for Mining, Metallurgy & Exploration (SME) will begin a new chapter by welcoming its new executive director and chief executive officer (CEO). Melissa Russell, a successful nonprofit executive with more than 30 years of experience in global association management, officially stepped into the role on Sept. 29, 2025. She succeeds longtime CEO Dave Kanagy, CAE, who is retiring in March 2026 after more than two decades of transformative leadership. “I am honored to begin this new chapter with SME and inspired by the vital role this community plays in shaping our world,” said Russell. “I look forward to listening, learning and working alongside this remarkable group of professionals to advance innovation, champion sustainability and create a brilliant future together.” Russell brings a deep portfolio of leadership experience in technical and industrial associations to SME. Most recently, she served as executive director of the Institute of Electrical and Electronics Engineers (IEEE) Computer Society, the largest of the IEEE’s 39 societies, with more than 50,000 members across 150 countries. During her tenure, she strengthened global engagement, advanced financial sustainability and launched strategic humanitarian initiatives.

Oct 1, 2025

By L. C. Morales

Mexico has an area of about 2 million km2 (772,260 sq miles), with volcanic activity, large shores and mountainous areas reaching as high as 6000 m (19,680 ft) above sea level. These conditions are favorable for most mineral deposits, some of commercial value and others as a source of mineral samples. In addition to its vast mineral wealth, Mexico has another valuable asset in its people. Even before the discovery of America, natives were successfully mining metals. During the colonial days, the mineral deposits were mined to increase the wealth of Spain. All this experience was passed from generation to generation. It created a tradition of mining and minerals processing engineers that currently accounts for about 182,000 people supported by mining-related activities. Nonmetallic minerals in Mexico have been mined by natives since the early days. They knew the value of kaolin clays for pottery, as evidenced by archeological findings. This experience was also passed from generation to generation and has become recognized worldwide as ceramic wares of high quality. The Talavera ceramic from Puebla is an example of family traditions many generations old.

Jan 1, 1994

By R. Kramer

The Process Mineralogy review arrived too late to appear in the May issue. The Process Mineralogy Committee scheduled programs with both SME and The Metallurgical Society. At the 1991 SME Annual Meeting in Denver, CO the committee sponsored five sessions containing 31 papers. Four process mineralogy sessions were sponsored at the 1992 annual TMS meeting in San Diego, CA. Process mineralogy is used to understand and evaluate mineral behaviors during mineral beneficiation, phase reactions during metallurgy, recoveries and reactions of precious metals during processing and mineral and phase behaviors with respect to environmental problems. The most recent refinement in mineralogical studies with respect to mineral beneficiation has been the wider use of image analysis and combined materials balancing techniques of image analysis data. Image analyzers that can perform analysis with respect to mineral beneficiation are expensive. They are used only for solving major processing problems. Nevertheless, the methodology of analysis continues to be refined. Much better data are collected, and methods of evaluating the data continue to improve. One interesting development involves modifying the ultrasound unit used in medical studies to perform a three-dimensional analysis of ore particles.

Jan 1, 1992

By Jerry Dolph

Hecla Mining's Lucky Friday Mine, located beneath the town of Mullan, ID, has been shaken since the 1960s by many deep underground rock bursts. The largest rock burst carried a magnitude of 3.5 on the Richter Scale. It occurred in 1969 when all of the stopes on a level approached an upper level at the same elevation. After that, a stair-step pattern was used to give the mine's levels more of an "arch." The article is an account of one of the more ferocious bursts to hit the miners of the Lucky Friday. I say "miners" instead of "mine" because I was there and it was a very personal experience for me. I had been working at the Lucky Friday for six years. During that time, I had heard and felt thousands of air blasts. In fact, in the early spring of 1986, the mine was experiencing as many as 1000 air blasts an hour, of different intensi¬ties, of course. Most of them sounded like popcorn popping. There were also a few bumps and occasionally a real boomer. That day did not seem any different

Jan 1, 1994

By Victor F. Hollister

Porphyry-type deposits are characterized by mineralization in, as well as adjacent to, an igneous body, usually a porphyritic stock. One deposit style includes both mineral dissemination and mineralized veinlets, and both porphyry copper and porphyry molybdenum deposits are characterized by dissemination and veinlet control of ore minerals. Those gold deposits that occur in stocks, with gold occur- ring in veinlets and disseminations within the stock, clearly are can- didates for consideration as porphyry gold type. Porphyry copper and porphyry molybdenum deposits are also characterized by potassic, phyllic, argillic, orpropyllitic alteration or some combination of these alteration types. Where two or more alteration zones are present, these are arranged in a sequential outcrop pattern. Gold occurring in dissemination and in veinlets in as well as adjacent to stocks, and which also occur in typical pervasive porphyry alteration suits, constitute a clearly defined class of deposit that fits the definition of a porphyry gold type. Porphyry copper deposits may carry appreciable gold. Porphyry copper-gold deposits are known from all porphyry copper provinces. This chapter is intended to cover porphyry gold occurrences that may have little or no copper or molybdenum as economic concentrations.

Jan 1, 1991

By Kevin Stuffle, James E. Sharp, Sean Premeau

Two process enhancements for the biological oxidative pretreatment of sulfidic gold ore for subsequent treatment with cyanide are discussed. These are the use of a high areal density ring and pin packing (BioBalls™) as substrate, and the use of a novel biological ferric generator. The BioBall™ packing when coated with concentrates for heap leach processing offers higher areal densities, while leaving more open volume for fluid flow than more commonly used substrates such as aggregate. An oxidation rate study was performed on crushed auriferous arsenopyrite whole ore to demonstrate the benefits of using the packing. The auriferous arsenopyrite grading 2.9% Fe and .212 OPT gold was 50 percent oxidized in 24 days. The biological ferric generator is a passive air-side trickle bed reactor that efficiently converts ferrous to ferric in a process stream. Conversion rates of .8g/L h ferrous to ferric are routinely obtained. Although the biologically generated ferric solutions have not yet been tested on gold ores or concentrates, prior work has demonstrated that the high ferric solutions which will result in rapid oxidation of sulfidic gold ores or concentrates.

Jan 1, 1997

By Thomas P. Kwiatkowski, John S. Anderson

The Massachusetts Bay Transportation Authority (MBTA) has undertaken an under-ground transit project to extend public transportation service from downtown Boston to the South Boston Piers area. This new system, known as the Transit way, will connect existing subway lines to this area which is comprised of approximately 300 acres, in light of the potential for 21 million square feet of development by 2010. This system includes construction of a concrete immersed tube tunnel crossing of Fort Point Channel. The crossing will be accomplished in the highly congested setting of down-town Boston and will be located just to the north of the famous Boston Tea Party ship exhibit and amid major Central Artery Construction activity. The most recent concrete tube constructed in the United States was in 1962. The Fort Point Channel Crossing will employ current design and construction methods commonly utilized in the Netherlands, Australia, Hong Kong and elsewhere. This paper will present the design philosophy, planning, and evaluation of alternative crossing methods which led to the selection of the concrete immersed tube tunnel and construction techniques envisioned for this particular application.

Jan 1, 1997

By Harry Sutcliffe, George B. Wallace, Madan M. Singh

INTRODUCTION Several recent estimates have predicted that the extent of underground tunneling in the future will far surpass past records. It is also emphasized that the expected increase depends largely on the cost of tunneling and hence every effort should be made to reduce this price. The largest items of expense in some tunneling programs are not related to the technical problems encountered but rather the human factors involved in contracting and executing the project. In order to examine the mutual interactions between the groups involved in tunnel programs, the Engineering Foundation sponsored a conference on "Owner-Engineer-Contractor Relations in Tunneling", July 12-16, 1971 at Deerfield, Massachusetts. The meeting was cosponsored by the Associated General Contractors of America and the Construction Division of the American Society of Civil Engineers. The seminar was attended by representatives of contractors, owners, and engineers who drafted and approved a set of recommendations based on the ideas generated during the discussions. It was also suggested that the resulting document be given as wide publicity as possible amongst the underground construction community. The First Annual Rapid Excavation and Tunneling Conference provides an excellent forum for this presentation.

Jan 1, 1997

By C. W. Schultz

Introduction The Mineral Resources Institute, The University of Alabama, has for the past three years been engaged in a program to develop a beneficiation system for eastern (Devonian) oil shales. One objective of that program was to evaluate advanced technologies for effecting a kerogen-mineral matter separation. Column flotation was among the advanced technologies selected for evaluation. Early in the program it was shown that column flotation was superior to conventional (mechanical) flotation and to the other advanced technologies being evaluated. The investigation then proceeded toward the further objective of defining the optimum operating conditions for column flotation. One observation made in the course of optimization testing was that introducing the feed into the froth (above the pulp-froth interface) resulted in an improved combination of concentrate grade and kerogen recovery. This observation was reported in a previous paper (Schultz and Bates, 1989). Because the practice of maintaining the pulp froth interface below the feed point is contrary to "conventional" practice, it was decided to subject the observation to a systematic series of tests. This paper describes a recent series of tests and the results that were obtained.

Jan 1, 1991

By George S. Koch

Today, after about 30 years of development, computer-based analysis of geoscience data has reached a mature phase. From the tentative early beginnings recorded in the proceedings of the APCOM meetings, geoscientists are now able to emphasize the need for both pertinent mathematical/statistical models and computer hardware and software. From those models that are well understood in the disciplines of statistics and mathematics and for which effective computational methods are available, practitioners select and develop methodology for their particular purposes. Computer hardware is typically assembled from off-the- shelf components now readily available, with particular emphasis, whenever feasible, on microcomputers for reasons of economy and control by the scientific or engineering user rather than by a bureaucratic computer center. Computer software may be written by the user in high level languages such as Pascal, FORTRAN, or LISP. However, more often today geoscientists use routines available in spreadsheets, data bases, or statistical packages. In so doing, they save time and, programming costs and take advantage of routines written and maintained by large, well- established organizations, while losing the flexibility in specifying exact input/output afforded by writing in a high level language.

Jan 1, 1989