Search Documents

A series of fault slip seismic events have occurred at Garson mine. The events have occurred during development advancement exposing faults, after the extraction of single stopes due to mining induced stress change, and due to time effects after delays of many days during which no mining had been conducted. This paper discusses the study completed consisting of a global or holistic approach aimed at mitigating some of the risks associated with the structurally controlled rockbursts at Garson. Background Garson mine is located in the south east area of the Sudbury Basin (Ontario, Canada). Mining occurs in two main ore bodies (the #1 Shear and the #4 Shear) which are copper-nickel-sulphide and occur within shear zones that (as well as the ore bodies) strike approximately east-west and dip steeply south. From the north (footwall), lithologies progress (Figure 1a) from norite (NR), to greenstone (GS), and finally to meta-sediment (MTSD). A generally WNW-ESE striking, bifurcated sub-vertical dyke of olivine diabase (OLDI) cuts the series. The current active mining block at Garson is between 4700L and 5100L (levels denote depth in feet below surface).

May 1, 2009

By Xiao Min You, D. R. Swonbourne

Smelting of Cu anode slimes involves the use of a slag to hold the oxidised Cu, but some Ag is also inevitably oxidised to the slag. The solubility of Ag in sodium silicate slags at 1 100 and 1 150 degrees C has now been determined over a very wide range of oxygen partial pressures. Silver was found to be present in the slags both as neutral atoms and as AgO(0.5). The activity coefficient for atomic Ag was a very strong function of slag composition and temperature, whereas that for AgO(0.5) was much less affected by slag composition and was almost independent of temperature over the limited range examined. The results reveal that the dissolved Ag cannot be fully recovered by reduction of the slag with very reducing gases

Jun 21, 1905

By B. Valentim

The methodology used to obtain fly ash subsamples of different sizes is generally based on wet or dry sieving methods. However, the worth of such methods is not certain if the methodology applied is not mentioned in the analytical procedure. After performing a fly ash mechanical dry sieving, the authors compared those results with the ones obtained by laser diffraction on the same samples and found unacceptable discrepancies. A preliminary study of a wet sieving analysis carried out on an economizer fly ash sample showed that this method was more effective than the dry sieving. The importance of standardizing the way samples are handled, pretreated and presented to the instrument of analysis are suggested and interlaboratory reproducibility trials are needed to create a common standard methodology to obtain large amounts of fly ash size fraction subsamples.

Jan 1, 2008

Jan 1, 1962

Adsorption of Alkylammoniums in the Interlayer of Montmorillonite and its Effect on the Viscosity of Organo-Montmorillonite Gels

Sep 13, 2010

By L. F. Ruppert, P. A. Freeman, R. C. Milici, S. J. Tewalt, L. J. Bragg

The U.S. Geological Survey has completed a dig-ital coal resource assessment of six of the top-producing coal beds and coal zones in the northern and central Appalachian Basin coal regions. These include the Pennsylvanian-aged Pittsburgh, Upper Freeport, Lower Kittanning, Fire Clay, Pond Creek, and Pocahontas No. 3 coal beds and coal zones. Resources were calculated on all of the coalbeds/zones, with the exception of the Lower Kittanning coal bed. Preliminary original resources are estimated at about 93 billion short tons (84 billion tonnes), of which about 66 billion short tons (60billion tonnes) remain. Much of the remaining coal in all five coal beds/zones is thinner [<3.5 ft (1.07m)] and deeper [>1,000 ft (305 m)] than the coal that has been mined, but economic resources are still available and mining in each coal bed/zones will continue throughout this decade and into the next given current market conditions.

Jan 1, 2001

By Jilai Xue

Fe-Ni alloys can be used as raw material in making stainless steel. Laterite nickel ore is one of mineral resources for producing nickel alloys. In this work, the laterite ore after dehydration at 800 °C and the anthracite as reducing agent were mixed for pre-reduction at 900 °C, and then reduced to form Fe-Ni alloys at 1550-1620 °C through carbon-thermal reduction process. A high Ni-content alloy component in the metallurgical mixture can be formed through pre-reduction. Better separation of the resulting metals from the slag is found with lower Ni-content alloys produced or higher temperatures during reduction. An effective processing of Fe-Ni alloys needs further understanding of the process fundamentals and optimizing of the process parameters.

Jan 1, 2010

By Douglas B. Silver

Traditional cycle theory would postulate that if you have a supply shortage relative to demand, the price will increase because buyers will incrementally increase the price they are willing to pay to ensure that their needs are fulfilled. As prices rise, more supply will be brought on and will eventually exceed demand. This supply excess will cause the price to decline as producers have to lower their prices to sell their goods. What is interesting is that cycles are simply volatility over time. Without the time factor, volatility simply goes up and down. When we add the time element, a cycle is created. This cycle can be big or small. In mining?s case, we are talking about a Super Cycle ? a big cycle. But a Su-per Cycle can be formed in two ways. It can form by either increasing the wavelength or the volatility. If these two elements are combined, a Super Cycle is formed. It is bigger than the normal cycle in terms of time duration and extent of volatility. A recent study (Fig. 1) conducted by Cuddington and Jarrett showed an interesting proof of Super Cycles and suggests that these cycles last between 15 and 30 years. So, what causes a Su-per Cycle? Is it a convergence of unrelated events or a consequence of related events? In a global community everything is related. Equilibrium theory would also take the position that a Super Cycle is a consequence of events.

Jan 1, 2008

By J. J. Demeter

Experiments were conducted in 2- and 4-inch-diameter standpipes to evaluate the effectiveness of standpipes as pressure seals. During the experiments, these standpipes conveyed Alan-Wood magnetite (60 to 230 U.S. standard sieve mesh) by gravity flow from one vessel to another of relatively higher pressure. The information obtained has been helpful in a Federal Bureau of Mines investigation of how to make either synthesis gas or hydrogen by a modified steam-iron process employing a continuous recycling stream of granular iron-iron oxide at temperatures of 600° to 900° C. In this process the mixture of granular material flows by gravity from a reduction vessel at low pressures to an oxidation vessel at higher pressures. Data from the 2- and 4-inch-diameter standpipes indicate that it would be practical to use a standpipe as a pressure seal between the reductor and oxidizer. Investigators found that, by gravity flow, the standpipe could convey the Alan-Wood magnetite against pressure gradients up to 1.07 pounds per square inch per foot of column height.

Jan 1, 1961

By Connie Postupack

The purpose of the workshop is to show the effect of various blasting factors on the overall results.

Jan 1, 1994

By Chad W. Brown

"A study of five commercially available solvent-extraction diluents in combination with three commercially available extractants under sub-Saharan African copper solvent-extraction conditions yielded intriguing results. A variety of physical and chemical property analyses showed that the diluents have some property differences, but overall the properties are similar and provide comparable solvent-extraction performance. Although each physical chemical property technique provides useful information, no individual test result suffices for prediction of diluent performance. Furthermore, a diluent should be evaluated within the conditions for which it is targeted to determine a true measure of performance. Overall, the diluents studied possess appropriate physicochemical properties for sub-Sahara Africa copper solvent-extraction conditions and can be utilized to achieve efficient, safe and reliable operations. INTRODUCTION Background Today, commercial SX diluents are available globally from a limited number of manufacturers. Production quality and consistency of these diluents have improved tremendously over the past 20 years. For example, diluent flash points have been increased incrementally to improve transport and handling while reducing fire hazards. In addition, properties have been successfully modified to minimize evaporative losses, ultimately reducing SX plant raw material costs. Diluent manufacturers have also focused on meeting performance requirements of SX plants, including eliminating components detrimental to SX operations, such as olefinic groups that can react with various species resulting in changing phase-disengagement properties over time, as well as ensuring that proper hydrocarbon components are present within diluent mixtures to maintain good reagent–metal complex solubility. These challenges have been met in the midst of ever-increasing stringent environmental regulations. Sub-Saharan Africa copper SX operations pose a unique set of conditions for diluents due to inherent ore compositions and the associated high reagent concentrations required for complete copper extraction. Chevron Phillips Chemical Company, LP has been manufacturing hydrocarbons and hydrocarbon-based diluents since the mid-80s, applying this experience to identify the physical properties considered crucial for proper performance in SX operations. This paper documents the findings of a study utilizing commercially available diluents in combination with extraction reagents commonly utilized in African SX operations to evaluate the relative performance of the diluents under sub-Saharan Africa copper SX conditions."

Jan 1, 2015

How the Australasian and Canadian Codes (VALMIN and CIMVal) approach mineral property valuation is described. Brief comment is also made on the International Valuation Standards CommitteeÆs interest in a global valuation standard for Mineral (Extractive) Industries and the South African SAMREC initiatives to adopt a VALMIN-like Code. The conventional tripartite classification of valuation approaches into those that are Market-based, Income-based and Cost-based is outlined. It is best practice to use as many of these approaches as possible (and as many methods as reasonable in the particular circumstances), given the quantity and quality of the data available on the Mineral Asset (which depends upon the state of development of the mineral property). The use of specific methods must satisfy the basic considerations of logic and reasonableness and the purpose of the valuation. The competence, judgement and repute of the valuer are critical factors, since all valuations are time and circumstance specific. What constitutes æMarket ValueÆ in the different jurisdictions is discussed and definitions are given. Challenges facing the globalisation of a VALMIN-type Code for the international Minerals Industry are the influence of real estate valuers and the US jurisdictional idiosyncrasies. This is mainly due to a fixation on real property rights with a preference for using real estate-like comparative sales techniques (Market Approach) to the exclusion of Income-based approaches; a regulatory reluctance in the US to accept that Resources have considerable value; and the International Accounting Standards BoardÆs preference for Historical, rather than Current Value, accounting.

Jan 1, 2002

By Conny Postupack

The first principle one usually learns about blasting is that competence in this field is best gained by experience in making blasts rather than by reading a book or by listening to a lecture. The reason for this is that there are a large number of variables affecting blasting results and not all of these can be accounted for by a few rules or a few sets of equations. Even an experienced in a new area, may have co make one or two himself to the new conditions with which he blaster when operating shots just to acclimate is faced.

Jan 1, 1991

By E. Ringdalen

Keywords: Pyrometallurgy, research, Norway, SINTEF, NTNU The Norwegian Ferro-alloy Industry and the model for research cooperation between SINTEF, NTNU, and the Norwegian ferro-alloy industry is presented as an introduction. The research within pyrometallurgy is illustrated by examples from characterisation of Mn-ores and characterisation of carbon materials. Examples from studies of reaction mechanisms in laboratory- and pilot-scale experiments are presented, in addition to an example of industrial off-gas measurements. Education possibilities at NTNU are also described.

Jan 1, 2011

By D. Lindeman, R. M. Nendick

"From a technologist's point of view, there have been few fundamental 'breakthroughs' in the process of gold extraction since the turn of the century. However, the industry has made a great deal of progress in its response to the problems that have arisen: a changing demand for products, lower grade and more refractory ores, inflated labour and materials cost and the increasing control of governmental legislation. The trend in North America and South Africa to alleviate these problems has been to adopt a common policy to process larger tonnages of lowgrade ore through more efficient milling circuits. Here, however, is where the similarity ends.The purpose of this paper is to emphasise the different principles of practice employed by extraction plants in North America and South Africa to achieve the same common goal, namely gold bullion.2.0 INTRODUCTIONTwo very important aspects of extraction metallurgy for which the metallurgical engineer is responsible are plant design and plant commissioning.In North America and South Africa the importance of these aspects is due to the fact that both are related to the financial success of the project of which they form part. Good design is imperative if the capital invested in both the plant and the whole mining undertaking is to reap maximum profit. Furthermore, good design leads to a carefully planned and well executed start-up procedure resulting in bringing the plant into production on time, at designed efficiency and within budget.Due to the competent nature of the quartz pebble conglomerate and quartzite ore on the South African Witwatersrand, the characteristics of the ore type are not much different from one mine to the other. Thus a significant operating knowledge and experience has been built up over the years and there is considerably less risk in selecting a gold extraction process route."

Jan 1, 1992

The general nature of the special constructional features that are required to provide safety from explosion hazards on machines approved as permissible by the Bureau of Mines is fairly well known to mining men who are at all interested in safety. These requirements are outlined in the schedules under the provisions of which the investigations of such machines are conducted. Also, the method of conducting inspections and tests of such machines has been described in Bureau of Mines Bulletin 305, Inspection and Testing of Mine Type Electrical Equipment for Permissibility, published in 1929. A more detailed knowledge of the special safety features of a particular machine is often useful and sometimes essential for inspectors, safety engineers, maintenance men, and engineers in selecting machines for a particular application. Three bulletins that give information of this nature have been-published by the bureau, viz., Bulletin 313, Permissible Storage-Battery Locomotives and Power Trucks. Bulletin 343, Permissible Coal-Handling Equipment. Bulletin 382, Permissible Coal-Cutting Equipment. Report of Investigations 3309, Permissible Electrically Operated Air Compressors, which contains similar information, was issued in August 1936, and a Report of Investigations 3326, Permissible Electrically Operated Room Hoists, was issued in January 1937. Thus, the present paper is the third to give detailed information concerning permissible machines of types not included in bulletins, and covers all the rock-dust distributors approved prior to October 1, 1936.

Jan 1, 1937

By Robert Labbe

The final tunnel lining for this project involved pumping vast quantities of concrete over large distances under the extremely busy streets of lower Manhattan. Approximately 68,000 cubic meters (89,000 cubic yards) were pumped from various locations over 152 meters (500 feet) below ground (Figure 1) to create nearly 14.5 kilometers (9 miles) of 3.05 meter (10 foot) diameter tunnel. Total distances pumped exceeded 1,645 meters (5,400 feet) horizontally after a vertical difference of over 152 meters (500 feet). The urban setting of the operation, coupled with the long distances over which concrete was pumped, created many problems which had to be dealt with along the way. A three-shift labor operation was implemented to allow sequential pouring of tunnel sections nearly every day. The fine tuning of the mix design was critical to make this operation successful.

By Jose R. Hernandez-Aguilar

"This paper revisits data from previous studies (Hernandez-Aguilar, 2010, 2011) to better understand the link between metallurgical performance and pulp-zone bubble size (Db) in full-scale flotation systems. To obtain conclusive evidence exclusively related to the pulp (collection) zone, the experiments were designed in those studies to control both the bubble generation method and the influence of the froth zone on the overall metallurgical performance in industrial and pilot-scale flotation columns. The results showed that Db had a significantly larger effect on the recovery of coarse (> 75 µm) particles compared to the effect on fine (< 16 µm) particles. It was observed that, under certain practical conditions, the recovery of coarse particles was close to zero, but dramatically increased by reducing Db. The evidence revealed an inconsistency of the so-called “k–PSb” model: at constant froth recovery, increasing Sb (i.e., the rate of production of bubble surface area) did not always result in higher recovery, as the model predicts. Furthermore, the evidence showed that it was not the Sb but the bubble size that proved to be a more reliable link to metallurgical performance. Only in the presence of suboptimal-sized bubbles (Db > 2 mm) did the froth zone seem to play a role, possibly reflecting an effect of pulp-zone bubble size on froth stability. However, the role of the froth was negligible for Db < 1 mm.High-resolution mineralogical measurements performed on process samples revealed that, regardless of the degree of liberation, Db had a profound effect on the shape of the recovery-by-size curve, particularly the coarse particle size fraction. This observation is key as it implies that the loss in efficiency associated with floating the coarse particles was not the result of neither particle hydrophobicity nor particle detachment issues: even in the absence of mechanical agitation, liberated and highly hydrophobic coarse particles did not seem to attach to the bubbles in the first place, an inefficiency that was corrected by reducing bubble size. The data analysis suggests that poor attachment efficiency can practically affect both fine and coarse particles but via different mechanisms which are discussed here."

Jan 1, 2017

The Mineral Sector Development Project, sponsored by the World Bank, has been set up to revise the legal, regulatory and fiscal framework for the minerals industry in Tanzania, with a view to attracting mining companies and investors to the country and facilitating future minerals development. One component of this project, the Environmental Management Framework for the Mineral Sector, was awarded to Wardell Armstrong of the UK and ENV Consult of Tanzania. In developing a new framework of environmental regulations, emphasis was placed on developing realistic standards which reflect local conditions and prevailing values. The main corner-stones of this approach are; effective environmental impact assessment procedures; establishment of environmental management procedures; and monitoring and auditing of companies? performance. The favoured approach involves a three-tier framework, as follows: ?Framework environmental provisions within the new Mining Act; ?Regulations covering more detailed environmental requirements ?Guidelines and/or Codes of Practice, which may in future become regulations in their own right. Careful consideration has been given, in developing the framework, to the limited resources likely to be available for implementation to the Ministry of Energy and Minerals and this has influenced the approach that has been adopted. This paper outlines the main components of the environmental management framework and discusses some of the important issues raised by these proposals.

Jan 1, 1998

WHY IS IT that smoke-abatement efforts do not bring more satisfactory results? The main reason is an incorrect estimate of the kind and size of the job. When an industrial community realizes that keeping the air clean is a project of similar magnitude to keeping streets clean, providing clean water, removing city waste, or guarding the moral atmosphere, then there maybe a real hope of success. We usually think of the project in too small terms. It is thought of as is the dog catcher or the boiler inspector--a matter of a man or two, a job or two, a small appropriation of variable and uncertain amount, to be abolished in a fit of economy and reestablished under pressure of a vigorous minority. Even so, it is surprising how much is obtained for the effort; but the community is rarely satisfied, for the job is bigger than it was conceived to be. Continuous, never-ceasing effort is required to clean up a smoky city. A few months of relaxation and the situation slips back some years of effort.

Jan 1, 1938