Search Documents

To reduce the respirable dust generated by auger-type continuous coal mining machines. The Approach: Use water sprays close to the cutting bits on the auger so that coal fragments are thoroughly wetted as they are formed to prevent dust dispersal into the ventilating air. How It Works: The "wet auger" system of dust control uses water sprays distributed on both shafts of auger type continuous miners. This approach has been tested underground by personnel of the Bureau's Twin Cities (Minn.) Mining Research Center on a Wilcox Mark 20 continuous miner, in a cost sharing contract with Buchanan & Sons Coal Company, Inc. Personnel of the Interior Department's Mining Enforcement and Safety Administration collected dust samples and analyzed the data. A test machine was fitted with six sprays on each auger (see Fig. 1). Water flow rates from 8 to 12 gpm at pressures from 90 to 120 psi, or about 8 gallons per ton of coal mined, were required. At these rates of water usage, mining personnel experienced no problems with work-

Jan 1, 1974

By C. J. A. Davie

"SUMMARY A practical application of nitric acid oxidation of sulphides, based on the principles of the Arseno process, has been developed for the Cinola ore. Development of the process has been based on testwork conducted by Bacon Donaldson of Vancouver and Hazen Research of Denver, and on conceptual engineering performed by Minproc Engineers of Denver.A comprehensive Stage II report for the project has been submitted to the B.C. permitting agencies, containing provisions for a zero discharge tailings impoundment system and prevention of acid mine drainage. Approval in principle is expected in early 1989.A feasibility study recently completed by Minproc Engineers and Davy McKee Corporation demonstrates that this project can be brought to production for a capital expenditure of C$120 million for a mill throughput of 6,000 tonnes/day and operated at a total direct operating cost of less than $20/tonne.INTRODUCTION The Cinola orebody was discovered in 1970. It is situated approximately in the centre of Graham Island, the largest of the Queen Charlotte Islands. It represents the mid to upper levels of a hydrothermal precious metals system, characterized by intense brecciation and silicification. Gold is associated with finely disseminated sulphides in a breccia matrix and in free form in numerous quartz veins.Ownership of the property has changed hands a number of times, and previous attempts to bring the property to production have failed. Two critical factors have frequently been blamed for difficulty in creating a successful project: namely, process and environment factors, hence the title of this paper.City Resources (Canada) Limited (""City"") acquired the property in 1986, and commenced an aggressive campaign to verify ore reserves, to carry out metallurgical research and to address environmental issues.PROJECT OVERVIEW When the Cinola orebody was discovered, the significance of hydrothermal mineraliza¬tion associated with crustal plate boundaries was not recognized, and for several years, the orebody was considered an uneconomic curiosity. If the type and location of orebody sought by many companies engaged in gold exploration were to be specified, it would probably be a description of the Cinola orebody - it is a large (greater than 1.5 million ounce), low grade (2.45 gm/tonne), refractory ore reserve associated with the Pacific rim crustal plate boundary. The industry appears to have recognized in the past few years that its future lies in the exploitation of such orebodies, and is prepared to come to grips with the technical problems associated with such ores. In this sense, the Cinola orebody might be considered to have come of age."

Jan 1, 1989

By W. D. Hausel

Archean supracrustal rocks of the South Pass greenstone belt of western Wyoming have been the State's most prolific source of gold and iron ore. Actual gold production statistics are incomplete, but as much as 400 to 500 thousand ounces may have been mined with some silver and tungsten as a by-product. Iron ore was also mined from the greenstone belt for 22 years, and production totaled more than 90 million tons. Immediately south of the exposed greenstone belt in the Oregon Buttes area, Tertiary boulder conglomerate, which has been eroded from the granite-greenstone terrain, may contain a gold resource of 28.5 million ounces (Love and others, 1978). The amount of gold placered from stream alluvium derived from these Tertiary conglomerates is unknown.

Jan 1, 1986

By Frank H. Madison

The percentage depletion deduction on Federal Income Tax Returns under the provisions of the 1939 Internal Revenue Code and of Sections 611 to Section 615, inclusive, of the revenue act of 1954, have created innumerable administrative difficulties, and a new interpretation of "gross income from the property" in that the Courts have expanded the ideas of what constitutes "gross income from the property" to a degree unheard of and unthought of prior to the enactment of these two codes. Originally, under the Revenue Acts of 1917, 1918, and 1920 depletion was allowable, based upon mine valuations as of March 1, 1913; if the mine was owned prior to March 1, 1913; upon cost, as of the date of acquisition if purchased subsequent to March 1, 1913; and upon a "discovery" basis if the mine was discovered after March 1, 1913, The "jab" for mine valuations as of March 1, 1913 and for discovery valuations and depletion was not as bad as it has been made out to be. Thousands of valuations and estimates of reserves were made and agreed upon between taxpayers and Internal Revenue Service engineers and as the years went on the answers have been found to be "reasonable." However, human nature being what it is each case was a battle of wits - of a sort - and many resulted in severe differences of opinion and litigation. As tax rates increased the situation was not bettered. I could talk for several hours on this phase of depletion but it is all past now andwould not give any real service or better understanding of the matter.

Jan 1, 1958

By J. H. Schuenemeyer

Uncertainty estimates on coal resources were computed as part of the U.S. Geological Survey’s National Coal Resource Assessment study of more than 60 coal beds and zones in the Appalachian Basin, the Colorado Plateau, the Gulf Coast, the Illinois Basin, and the Northern Rocky Mountains and Great Plains. The estimates were made to provide zone specific measures of uncertainty on the historical categories of geological assurance, namely measured, indicated, inferred and hypothetical. Previous estimates were based solely upon distance from a drill hole. These new estimates incorporate site-specific variability and spatial correlation and indicate that there is considerable difference in variability within and between regions. Uncertainty estimates for the measured category are discussed in this paper.

Jan 1, 2001

By R. B. Booth, W. F. Linke

The continuous interest of the American Cyanamid Company in producing superior polymeric flocculants and dispersants for the mining industry has resulted in a broad, general study of the physical chemistry of mineral-polymer systems. The aim of this program has been to establish a sound theoretical basis on which practical problems could be analyzed, and which would lead to the development of new and improved flocculating and dispersing agents. This study has required the cooperative effort of physical, analytical, and polymer chemists, as well as engineers familiar with mining problems. This report summarizes the results of some of our investigations over the past two years. Further studies along these and other lines are in progress and will be reported in the near future. MEASURING FLOCCULATION IN THE LABORATORY The foremost problem in studying flocculation in the laboratory has been to establish reproducible methods of comparing and evaluating the effectiveness of various reagents. Previous workers have measured settling -rates 1,8 filtration rates2 , and sediment volumes3 . Direct observations of the floc size, or the clarity of the supernatant liquid, can also be used. AIthough these parameters are all interrelated, they do not always measure the same physical properties of the suspensions, and hence are not equally useful or reliable. Whatever the method of comparison selected. the testing procedure must be carefully defined and standardized. The results must be satisfactorily reproducible, and for practical purposes must accurately reflect the results obtained in mill use. In order to compare the data obtained in these various types of test, the physical nature of the flocculated system must be examined in some detail. In an unflocculated system, only the larger or denser particles (the "sands") settle at a useful rate. The sediment can be observed to build up from the bottom of the cylinder, while the fines remain in suspension for a long period of time. If the system is not disturbed, even the microscopic fines can be seen to classify themselves as they fall over a period of days. When a high molecular weight polymer is added to the system, the colloidal particles are tied together randomly in flocs, and the sands and fines settle together. The line of demarkation between solid and liquid phases moves downward from the top of the cylinder. The settling rate of the flocs depends on their size and on their effective density. For a given mineral sample, the larger the flocs, the faster the settling. Since the large flocs cannot pack as closely as small ones, they produce a sediment with more pore spaces, and hence of larger volume, which is easier to pump and to agitate. Although it is nearly impossible to measure individual floc sizes, it is relatively easy to determine settling rates and sediment volumes. Of these two, the settling rate is simpIer to measure, and hence generally more practical. Reproducible sediment volumes can only be obtained by allowing the solids to pack for a rather long period of time (e.g., hours to days), and although the volumes thus observed are directly related to the degree of flocculation (average floc size), it is often impractical to wait so long for the results.

Jan 1, 1961

By R J. Goldfarb, A B. Christie, D I. Groves

Small orogenic gold deposits have the same deposit-scale geological and geochemical features as those that characterise giant orogenic gold systems (>16 Moz Au). Therefore, a broader-scale approach is needed to identify the critical controls on giant deposits and their disproportionate distribution throughout time and space. Ages of giant gold systems cluster around well-defined periods of lithospheric growth at continental margins, and it is orogen-scale processes during these Late Archaean, Early Proterozoic and Phanerozoic times that determine gold endowment of a province.   A critical factor for giant orogenic gold provinces appears to be asthenospheric upwelling at the time of gold mineralisation to most effectively transfer the thermal energy required to initiate and sustain high hydrothermal fluid flux. The extent of this fluid flux should be related to thickness of the lithosphere beneath a province at the time of gold mineralisation, such that giant gold deposits are much more likely to develop in orogens with oceanic or thinned continental lithosphere. A proxy for the latter is likely to be a short premineralisation crustal history such that thick subcontinental lithospheric mantle was not developed. Conversely, orogens with protracted premineralisation crustal histories are more likely to have a thick subcontinental lithospheric mantle, which is difficult to delaminate and, hence, such provinces will normally be poorly endowed. The nature of the lithosphere also influences the intrinsic gold concentrations of potential source rocks, with back-arc basalts, transitional basalts and basanites enriched in gold relative to other rock sequences. Thus, segments of orogens with thin lithosphere may be defined by conjunction of giant-scale fluid flux through gold-enriched sequences.   Although the nature of the lithosphere plays the crucial role in dictating which orogenic gold provinces will contain one or more giant deposits, the precise siting of those giants depends on the critical conjunction of a number of province-scale factors that control fluid conduits, traps, and seals in tectonically and lithospherically suitable terranes within accretionary orogens.

Jan 1, 2005

By Vladimir Panjkovic, Ostrovski. Oieg, Campbell Cripps Clark, John Truelove

"Effects of properties of raw materials and blast on the performance of an iron bath reactor have been examined by a mathematical model. The model consists of three modules: 1) chemical reactions in the gas phase and heat transfer from gas to droplets ejected from the bath; 2) heat losses from the vessel and radiative heat transfer from the freeboard to the bath; and 3) heat and mass balances for the bath. The following parameters of the process are calculated: coal, ore, flux and oxygen consumption, post-combustion ratio and heat-transfer efficiency, temperature and composition of the off-gas, and slag and metal chemistry.IntroductionOne of the anticipated advantages of smelting reduction over conventional ironmaking is the use of lower-grade raw materials. In this work, the effect of-properties of raw materials on the performance of an iron-bath reactor is examined with a numerical model. The model is also used to assess the effect of properties of the blast (flowrate, temperature and oxygen enrichment) and ejected droplets (generation rate, size and ratio of total weights of slag and iron droplets) on the key parameters of the process. In the process coal, oxygen, ore (which may be partly prereduced) and fluxes for specified slag composition are charged to the bath. Slag and iron droplets are ejected from the bath into the gas phase, where they are heated before returning to the bath. Iron droplets undergo decarburisation and reoxidation with CO2 and H2O. Dust is also generated from the bath, and oxygen or preheated air for post combustion is injected from the top of the vessel.The model consists of three modules: 1) reactions in the gas phase and heat transfer from gas to droplets ejected from the bath; 2) heat losses from the vessel and radiative heat transfer from the freeboard to the bath; and 3) heat and mass balances for the bath. The structure of the model and the data exchange between the modules are shown in Fig. 1. The following parameters of the process are calculated: coal, ore, flux and oxygen consumption, postcombustion ratio (PCR), heat transfer efficiency (HTE), off-gas temperature and composition, slag and metal chemistry, and rates of decarburisation and reoxidation of the iron droplets."

Jan 1, 1996

By E. A. Lowe, A. F. Bellamy, J. W. Smith

"In the autumn of 1977 Bethlehem management initiated feasibility studies on recovery of by-product molybdenum from concentrate produced at the existing Highland Valley mining operation. Over the fall and winter months test work was carried forward concurrent with design, flowsheet, equipment specification and cost studies. The decision was made to go ahead with a 200 ton-per-day treatment plant. Construction started in early 1978 and progressed to an initial start-up stage in mid-June. Full operational status was reached in August 1978. Operational results through August 1979 are presented. INTRODUCTIONBethlehem Copper Corporation operates a 20,000 ton-per-day Open Pit Mine and Flotation Plant located in the Highland Valley, some 30 air miles Southwest of Kamloops and 20 miles Southeast of Ashcroft, B.C.Two open pits are worked; the Iona Pit with limited reserves of higher Mo content, and the lower grade, more extensive Jersey Pit. Upwards of 150 tons per day of bornite-chalcopyrite bulk concentrate is produced, ranging 0.25% to 1.5% in molybdenum grade depending on the area mined."

Jan 1, 1980

Grinding Mill Operation and Maintenance - Central to Asset Management Since 2005, RME has pursued a vision for a new grinding plant operational paradigm, made possible by RME's latest Mill Relining Systems. At some sites, new liners degrade SAG mill performance. The variables include mill volume loss, rotational speed limitations (ball strike) and liner designs developed for longer and longer life but without a backward glance at metallurgical consequences of whole plant performance. Freshly relined mills can initially deliver as little as 80 per cent of their maximum throughput, that maximum occurring toward the end of the liners' wear life. RME's proposition is to see new liners designed for maximum commercial performance. This may mean more frequent mill relines but with liners designed to yield optimum grinding, metallurgical and profitability performance, not maximum life. In other words, mill liner profiles and relining speed become key profitability contributors and not simply 'must do' maintenance functions and costs. This paper includes a short history of RME's Mill Relining System development (Appendix A). These are the enabling technologies which permit more frequent liner exchange without incurring additional downtime imposts. The body of this paper outlines RME's vision of a 'liner profile vs. profitability' commercial model, underpinned by the rigour of PAS 55-1:2008 Asset Management Part 1: Specification for the optimised management of physical assets. The technical elements can be developed either intuitively (based on plant experience) or by using a combination of new measurement and modelling technologies. These new measurement and modelling tools provide the opportunity to predict the optimum technical solution for the maximum commercial outcome. Much of this can be modelled off-line, in the virtual world, before asking senior management to commit to an expensive liner experiment. The potential benefits are compelling.

Sep 13, 2010

By Hirst H, McAfee J

In December, 1934, Mr. R. Sussex extruded some silver lead alloy wires in order to determine their electrical resistance. After the determinations had been made each wire was threaded through a sheet of paper on which the composition was noted. The wires were placed in a more or less tangled mass in a cupboard in March, 1935. It was not until September, 1936, that they were re-examined, and it was found that during the eighteen months some of the wires had corroded very badly. It was not until March, 1938, that the wires and the corrosion product could be examined, and the results are given in the following pages. It is of interest to note that none of the numerous silver-lead alloys which have been used for creep testing in the rolled condition have shown a similarphenomenon. The silver content of the rolled alloys was, however, never greater than 0·1%.GENERAL APPEARANCE OF THE CORRODED WIRESThe wires contained 0·1% up to 28% of silver, and a general examination showed that the corrosion had progressed farther the higher the silver content. This can be seen in Fig. 1, which is a photograph taken in March, 1938, of typical wires at a 'magnification of five diameters. In the early stages the corrosive action seems to be localized and an area of grey, yellow or reddish brown powder appears. The grey corrosion product is by far the one, most frequently seen, and in the later stages the only one visible from the outside. The reddish coloured product is sometimes seen on the residual metallic centre when the grey product has been broken away.The irregular extent of the corrosion can be seen in Fig. 2, which shows (natural size) the 5% silver wire after standing two years. The corroded parts are seen to be much thicker than the slightly corroded ones. The corrosion product, being non-metallic, is quite brittle and falls away from the wire on bending. In the extreme case the' whole wire has corroded and presents a cracked appearance as seen in Fig. 1 (281% silver).An approximate idea of the extent of corrosion can be obtained by measuring the diameter of the corroded part. The original diameter in each case was ·050/ ·051 inches and in Table I are given the diameters of the corroded parts after Hand 3 years respectively. When the diameter...

Jan 1, 1941

By George J. Conroy

To provide data as a basis for proposed acceptance standards and procedures covering permanent splices in trailing cables, the Bureau of Mines conducted testing programs on the flexure life in flat types W and G dc trailing cable splices and ground conductors. Primary reliance was placed on laboratory testing, although some cross comparisons were made at manufacturers' plants and mine operations Besides providing data for acceptance standards and procedures, results of the program should promote the general improvement of commercially available splice kits.

Jan 1, 1977

By Tom Ireland, Tony Rock

The proposed 1.83km long twin bore A3 Hindhead road tunnel planned for contruction in 2008 is being delivered under a Highways Agency Early Contractor Involvement (ECI) contract. The proposed construction methodology is progressive mechanical excavation of a horseshoe shaped tunnel with shotcrete installed close behind the face using robotic spraying equipment. The tunneling medium is a ‘soft rock’ sandstone for which there was little previous tunneling experience, requiring extensive geotechnical investigations and an innovative approach to lining design. A 240m long portal section though sandy material utilising a steel pipe umbrella is also required. This paper describes the development of the tunnel planning and design including the most recent developments in UK road tunnels, and the innovation included in the ‘permanent’ primary lining design.

Jan 1, 2007

By Thomas T., Read

IT does not seem practicable to review all the other specialized curricula that have developed in the mineral industries field in so much detail as has been given for petroleum. Nor is it easy to draw a definite line between true curricula, leading to a designated degree in the special subject, and options, which may range from the mere substitution of one or two courses for others ' in the final years to differences so extensive as almost to amount to separate curricula. Even to attempt to catalogue all the options that have been offered at one time or another would , require too much space. The remainder of this discussion, there- fore, will be confined to three topics which seem to be of major importance. Mining and metallurgical curricula will be covered in a later chapter. Geology The first, from the historical view, is geology in its relation to the mineral industries. Previous, chapters have made clear that in the early years of mineral industry instruction in the United States economic geology and mining engineering, so overlapped one another that men who were by training and experience economic geologists were appointed professors of mining, while men who had graduated as mining engineers sometimes developed into professors of geology. Even today men whose basic training was in- geology as a pure science, and who perhaps took a doctor's .degree in that subject, have attained such distinction in the mineral industries as to be universally accepted as "mining men," and their right to be regarded as mining engineers would not be questioned, even though 'they did not .take a degree in engineering. Nevertheless the distinction does exist, and has been made a concrete reality in recent years by the enactment of

Jan 1, 1941

By Emmanuel N. Zevgolis

Energy required for roasting and smelting of a nickeliferous laterite ore by the rotary kiln - electric furnace process is investigated. From this work it comes that thermal energy is about 65% of the total energy needed and the rest is electrical. Also, 61.3% of thermal energy input in the roasting step (of all combustibles fed into the rotary kilns) is used for pre - heating, 11.6% for pre - reduction and the rest (27.1%) corresponds to the energy of the remaining carbon in the rotary kiln products (i.e., calcine, dust and coatings). Carbon entering the system is used as follows: 57.9% for combustion, 37.1% for reduction and the rest (5.0%) remains unburnt. Exploitation of energy from gases of both furnaces, as well as the higher possible reduction degree, the optimum temperature of the calcine and also elimination of the excess air in the rotary kilns, improve significantly energy balance and economics of the process.

Jan 1, 2006

By H. H. Einstein

This paper reviews how uncertainty has been dealt with over the past 40 years using the decision making cycle as a frame of reference. The review of the phases of this cycle, as applied to rockmechanics and rock engineering, namely characterization, performance analysis, updating and decision making shows that in each, progress has been made over the past 40 years, although most of the basic concepts existed already in the 1960’s. Characterization is the area in which the greatest scientific steps were taken, this phase and performance analysis also gained from the tremendously expanded computational capabilities which allow one to use both more complex and more practically oriented models. The greatest practical advance is without using any doubt in risk based decision making although its acceptance shows interesting differences between different professions. Dans l’article suivant on utilise le cycle de décision pour illustrer le développement du traitement des incertitudes en mécanique des roches et en construction en roche dans les quarante années passées. La revue des phases du cycle de décision montre qu’on a fait du progrès dans chaque phase du cycle de décision, c’est à dire dans la caractérisation, dans l’analyse et la prédiction du comportement, dans l’actualisation et dans l’acte de décision, même si les concepts fondamentaux existaient déjà dans les années 1960. Les plus grands avancements scientifiques se trouvent dans le domaine de la caractérisation tandis que l’analyse prédictive profitait du développement de l’informatique qui a mené à des modèles plus complexes mais aussi plus pratiques. Le plus grand progrès est sans doute dans le domaine de l’acte de décision sur la base des risques. Ce procédé est devenu assez commun même s’il y a encore des différences d’acceptation entre différentes professions. Im vorliegenden Artikel wird der Entscheidungszyklus gebraucht, um darzustellen wie sich derUmgang mit Unsicherheiten im Felsbau während der letzen 40 Jahre entwickelt hat. DerÜberblick über die Phasen des Entscheidungsprozesses zeigt, dass bei der Anwendung in derFelsmechanik und im Felsbau, in allen Phasen d.h. bei der Charakterisierung, bei der analytischenVorhersage, beim Aktualisieren und bei der Entscheidungsfindung Fortschritte gemacht wurden,obwohl die grundlegenden Konzepte bereits in den 1960er Jahren existierten. Im Gebiet derCharakterisierung gab es wohl die grössten wissenschaftlichen Entwicklungen, während dieanalytische Vorhersage vor allem von den Fortschritten der Informatik profitierte, welchekomplexere wie auch praktischere Modelle möglich machte. Der grösste Fortschritt ist ganz sicherin der Entscheidungsfindung zu beobachten, wo Risikobetrachtungen gang und gäbe sind, obwohlhier noch einige Unterschiede zwischen verschiedenen Berufsgattungen zu finden sind.

Jan 1, 2003

By Maurice Guillaud

The most striking innovations on diaphragm-wall construction plant are those associated with continuous real-time trajectory monitoring of the excavating tool (either a grab or a hydro-cutter). The recent equipments are fitted with clinometers and gyrometers to control deflection, rotation or deviation from the vertical, thus allowing to install diaphragm-walls with a verticality accuracy of less than 0.3%. One of the greatest advantages of extensive use of on-board IT systems on the Hydrocutters and hydraulic grab machines is that it aids quality control by automatically producing complete real-time reports of all excavating data (verticality, depth, type of ground, rate of progress, stoppages, etc.). These reports are available to the Engineer, providing the total transparency required for Works Supervision and the Quality Assurance Plan. They also provide the Contractor with input data for databases used for optimising efficiency and progress criteria on future jobs.

Jan 1, 2002

By J. D. Morgan

In the first half of the year, lessening of cold war tensions was welcome. But Iraq's invasion of Kuwait in the second half led to the Persian Gulf War in January and February 1991. This caused an oil shock that dampened the economy. So the US gross national product rose only 0.9% to $5,463 billion (US billion = 109). The buildup of military forces in the Persian Gulf area focused greater attention not only on petroleum but also on other strategic materials. The Department of Defense continued to review stockpile goals and to upgrade several mineral materials. In addition, the Bureau of Mines continued to maintain the standby Emergency Minerals Administration. The Defense Production Act, which authorizes priorities, alloca¬tions and supply expansion, lapsed on Oct. 20. So the Selective Service Act of 1967 became the authority for assuring that orders of the armed forces and defense atomic-energy programs were given priority treatment. Consumer demand strongly affects mining worldwide. US citizens carry significant debt, and large stocks of housing and consumer goods are already in place. Some 250 million persons have 188 million licensed motor vehicles and 100 million dwelling units. Consequently, new car production fell 11 %, to 6.1 million units. Truck and bus production fell 8%, to 3.7 million units and new private housing starts fell 13% to 1.2 million units.

Jan 1, 1991

By Rozbeh Moghaddam, William D. Lawson, Priyantha W. Jayawickrama, Hoyoung Seo, James G. Surles

"This study provides calibration of resistance factors (?) for design of driven piles to implement Load and Resistance Factor Design (LRFD) for bridge foundations using Texas Cone Penetration (TCP) Test data. The basic research approach was to compile a database of published full-scale load tests including projects from the Texas Department of Transportation’s (TxDOT) historical archive and projects from neighboring state DOTs. Load test results from neighboring states were leveraged by performing new geotechnical borings with TCP tests at the project sites. The final dataset consisted of 30 load tests performed on precast square concrete piles, with pile widths ranging from 356 to 508 mm and penetration depths ranging from 5.2 to 25.5 m, driven in soils. Ultimate capacities for each load test were interpreted based on Davisson, 5%, and 10% settlement criteria. These measured ultimate capacities were compared against predicted capacities estimated from TCP blow count values (NTCP) and design charts following the procedures outlined in TxDOT’s Geotechnical Manual. From the comparisons, statistical parameters of the biases (??= measured capacity/predicted capacity) such as mean and coefficient of variation were obtained. Resistance factors (?) for LRFD were then determined using Monte-Carlo simulations for each ultimate capacity criteria with the target reliability indices of 2.33 and 3.00.INTRODUCTIONThe Texas Department of Transportation (TxDOT) has used the Texas Cone Penetration (TCP) test since its development in the 1940s. The TCP test is an in-situ penetration test to characterize the materials encountered during geotechnical exploration. Texas currently maintains over 53,000 bridges in the National Bridge Inventory (FHWA 2016), and most of these bridges plus other transportation infrastructure in Texas are supported by foundations designed using the TCP test and its associated foundation design method. The Oklahoma DOT adopted the TCP test and foundation design approach in the 1970s, so the foundations for most of the 23,000 bridges in Oklahoma’s inventory were also designed using the TCP method. With this significant body of experience, the TCP method has been viewed as a straightforward, relatively easy-touse foundation design method that consistently yields safe, serviceable, economical, and maintainable foundations. TxDOT’s deep foundation design method is documented in the TxDOT Geotechnical Manual (TxDOT 2012) and currently employs the allowable stress design (ASD) approach. However, the Federal Highway Administration (FHWA) has mandated that the states begin to implement the LRFD method in place of the older ASD approach (Densmore 2000). This paper presents resistance factors at ultimate limit state (ULS) for design of driven piles using the TCP test, resulting from efforts to be in compliance with the FHWA policy."

Jan 1, 2017

By A. L. Martikainen

In fluctuating airflow, continuous air velocity recording is the most reliable method of air velocity measurement. It allows for fast recognition of changes and the calculation of long-term averages. Also, it enables the mine operator to identify when the airflow has decreased to a point requiring action. Using ultrasonic anemometers provides an accurate option for continuous air velocity monitoring. This paper provides information about the effect of common obstructions in underground mining on air velocity readings. Stationary and moving obstructions are used to represent workers and equipment that would cause discrepancies in measured airflow. Also, it is important to know how large of a sample size is required to ensure reasonable accuracy of results. Statistical analysis is used to evaluate the required sample size. The sampling procedure is further studied by comparing two different sample rates. The results show that obstructions provide noticeable differences in air velocity measurements. Also, movement of obstructions can be recognized from changes in results. Surprisingly small sample sizes provide reliable air velocity information. Standard sample rates are found to be suitable for the underground environment.

Jan 1, 2011