Search Documents

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

Hydrodynamic investigations in exploratory boreholes and grouting holes are conducted for the purpose of obtain¬ing information about the hydraulic properties of the hydrostratigraphic section to be intersected by the proposed underground workings. The information obtained from the investigations provides the basis for calculating the hydrau¬lic coefficients of fractured permeable rock, the dimensions of the anticipated grout isolation curtain(s) around the un¬derground workings, the number and location of grouting holes, the injection pressure modes, and also the volume(s) of grout that will be required (Anon., 1976, 1978). The following data on each aquifer are obtained from the investigations conducted in monitoring and grouting bore¬holes and the analysis of the results: 1) the top of each hydrostratigraphic unit, 2) the thickness of each unit, 3) the ground water fluid potential distribution in each unit, 4) the coefficient of permeability, 5) the piezoconductivity, 6) the fracture porosity, 7) the geometry of the fractures in the rock, 8) the elasticity-compressibility coefficient of the fractured rock, 9) the chemical composition of the ground water, 10) the direction of flow of the ground water, and 11) the expected inflow rate of water into the shaft, drift or tunnel. STG uses its DAU-3M type flowmeter to conduct in¬vestigations of directions of flow in vertical, inclined and horizontal drillholes. The DAU-6 instrument is used to de¬termine the direction of flow of ground water in each frac¬ture or fractured aquifer. Various singular and double DAU type packers are used for pumping and for injection studies (tests) and for flowmeter investigations. Normally the instruments enumerated above permit in¬vestigations to be conducted in each separate aquifer with¬out reinforcing the holes with casings. On the basis of these investigative data, both the hydraulic properties of unfractured rock and the hydraulic properties of the fractured rock are estimated. Dual porosity rocks require special attention because they tend to segregate the grout. 3.1 FLOWMETER INVESTIGATIONS IN BOREHOLES The STG flowmetric methodology is based on the mea¬surement of the ground water flow rate through the borehole by hydrostratigraphic interval after the disturbance of the hydrostatic equilibrium in the "hole-aquifer system" (after pumping or injecting). The relationship of the head changes to the discharge into or from a particular hydrostratigraphic unit obtained during the tests serve as the basis for calcu¬lating the hydraulic properties. Flowmetric investigations facilitate the determination of the number of aquifers, their depths, their thickness, the hydraulic properties of the fractured rock and the magnitude and direction of the flow of ground water. 3.1.1 FLOWMETER HARDWARE STG conducts flowmetric investigations in boreholes using its DAU-3M-108, DAU-3M-73, DAU-3M-57 and DAU-3M-44 instruments.' They have respective external diameters of 108, 73, 57 and 44 mm. The type of flowmeter selected for use depends on the borehole geometry and the technological scheme for carrying out the investigations. Boreholes with a drilling diameter of 76-93 mm are inves¬tigated with the DAU-3M-73 flowmeter; boreholes drilled by bits with a diameter of 112 mm and more are investi¬gated using the DAU-3M-108 flowmeter. The DAU-3M¬108 and DAU-3M-57 instruments are used for flowmetric investigations with a packer. 3.1.1.1 The Downhole Sensor The sensor design of the DAU-3M-73 hole flowmeter is shown in Fig. 2. The design of the DAU-3M-108 instru¬ment is similar to the design of the DAU-3M-73 instrument. The frame of the flowmeter sensor shown in Fig. 2 consists of a casing, an upper and lower centering mount and two rings to which the guiding rods are attached. The upper rods are built into the connector bushing; the lower rods are built into the coupling sleeve. The borehole cable is attached using a half-coupling, a packing ring and a constriction nut. Thus, the frame of the flowmeter sensor is made so that the free passage of water to the impeller is facilitated along with the necessary rigidity. The primary moving component of the flowmeter is the double-bladed impeller, which rotates on cobalt-tungsten pivots and agate thrust bearings. Special extended air cham¬bers protect the supports of the impeller from the action of the borehole fluid which may contain fibrous and abrasive particles. The air located in the chambers shields the sup¬ports from direct contact with the borehole fluid when the sensor operates in a borehole. The hollow casing of the impeller serves the function of a lower cap. The upper cap is attached to the casing using a threaded connector; it is affixed also with a lock-nut. An adjusting screw with a

Jan 1, 1993

By J. E. Hoffman, Massimo Maccagni, T. J. Keefe, Marco Olper, O&apos

The problem relating to the use of insoluble anodes in acidic and highly aggressive environments has still not been definitely solved, and it is therefore a recurring subject of discussion. The fields of application in which insoluble anodes play a fundamental role are mainly in the electrolytic extraction of metals, in cathodic protection with impressed current, and in the production of oxidized halogenated salts. Based on the foregoing, B.U.S Engitec Servizi Ambientali (BESA) developed an electrode suitable for the use in the above-mentioned system. The basic component of the BESA anode is a bimetallic wire made of a copper rod (core) covered by a thin layer of valve metal, to be chosen between tantalum (Ta) and niobium (Nb). The wires, coated with suitable catalyst (PbO2, Pt or others) are inserted in a plastic frame and fixed to a current feeder by means of a screw, ensuring an optimal contact. Experimental data on the operating conditions, such as kind of electrolyte, current density, electrode potential, corrosion tests and fields of possible application, are described.

Jan 1, 1993

By L. Adler

Existing classifications of mining and construction equipment have had major deficiencies. They often lack organization, balance, and have remained obscure. Particularly when proceeding to great.er resolution these deficiencies have proven crippling. By adopting "Classes", "Groups" f "Types" and "Kinds" at successive degrees of refinement, a "Taxonomy" is developed based on clear visual differentiation or on a "Morphology??. This symbiotic application, adopted from the Biological Sciences, yields clear, simple and unambiguous results. Supporting this effort are guidelines for easily and credibly sketching equipment which are also distinctive. Numerous illustrative examples are provided. Communications are improved and the engineer obtains a confident feel for the equipment at hand.

Jan 1, 1989

By Karl W. Mote, R. K. "Ivan" Urnovitz

One of the Northwest Mining Association's guide-lines is: "If you always do what you've always done, you'll always get what you've always gotten." Another way of saying this is, simply, "when the road curves, don't refuse to turn." Our industry has been roundly criticized for living in the old political world, and, I believe, justifiably so. Until about 20 years ago, members of both houses of Congress deferred to specialists among their members for mining legislation. This was true for all public lands and natural resource issues, and were referred to as the mining bloc, or the timber bloc, or the ranching bloc. We felt safe, and to a large degree, were safe in the sense that western members of the US House of Representatives and of the US Senate understood the need for multiple use of public lands, and the need for the natural resources they supply. They also knew what it takes to stay in business and how to create the economic atmosphere that encourages private industry to find and provide the natural resources. Almost daily, members of our industry bemoan the destructive effects that current regulations, let alone new proposals, are having on American industry. And, there are some intriguing aspects for us to ponder. First, the specific complaint about the government is not regulation per se, but rather that the rules or policies don't make sense. We recognize that few understand our industry, but we have assumed that the government will rely on people experienced and knowledgeable in the area being brought under government controls. There was a time that this assumption was valid, but it is no longer true since we have entered the era of the professional regulator. Much like the MBA who believes that a professional manager can manage anywhere, the new breed of regulator sincerely believes that process is the key to developing effective regulations or programs. They reason the process virtually assures that all the pertinent facts will inevitably come to light and, after receiving appropriate considerations, will result in the proper decision being reached and implemented. Unfortunately, following the process also allows politics to play a new and greater role than ever before, since information based on what can only be called weird-science can now be presented to the professional regulator and accepted as fact. Regulators do not have the background to question the basic tenets of the conclusion being presented to them. To add insult to injury, testimony from people in the industry involved, intended to set the record straight, is too easily discounted as being merely self-serving. A second aspect is that the question of why the associations aren't doing more to stop poorly conceived legislative and regulatory proposals, or to counter the ever-increasing influence of the selfappointed public interest groups is being increasingly discussed. This is occurring despite the fact that there is a higher level of involvement and closer cooperation between the various associations than ever before. This raises a most important question: where are we going wrong? In the last 20 years or so, major changes have taken place. A new philosophy, taking advantage of the public's recognition of need to protect our environment, has swept through the nation, resulting in a whole new body of law enacted to assure environmental protection. We all acknowledge the need to prevent undue degradation during the course of mineral development, and we all consider ourselves to be responsible stewards of the land, because we live and work in the outdoors and know the importance of environmental protection. The changes in the federal statutes apply now to every aspect of mineral discovery, development, and production, and assure adequate reclamation of lands when we are done. Along with the positive changes, are a constant barrage of attempts to stop public land use, or stop mining, or stop any new economic development, ostensibly to "protect the environment," but often reflecting a hidden agenda of social reform. These types of extreme, irrational, and just plain impossible proposals are everyday occurrences, but we have not geared up to challenge all the proposals which could end mining. Instead, we did what we always had done. The road turned, but we didn't. And we wondered why those who had always protected mining weren't doing their job, and why we were having such limited success in reining in the regulators. The Congress had changed, the public demands had changed, the recognition of importance of natural resources had

Jan 1, 1991

By W. F. Cannon

Many high-grade manganese deposits of the world occur in marine transgressive sedimentary sequences deposited on stable platforms. These include the Nikopol and related deposits in the Soviet Union and Groote Eylandt, Australia, among others. We suggest that the Atlantic and Gulf Coastal Plains and the vast area of Cretaceous rocks in the middle of North America are favorable provinces for sedimentary manganese deposits because regionally transgressive units are widespread. North America has 16% of the world's land area but only about 0.2% of known high-grade manganese reserves. This disparity is difficult to reconcile in view of the fact that large areas of North America are underlain by rocks that we consider at least broadly favorable to contain manganese ores, and we suggest, therefore, that important high-grade deposits remain to be found in North America.

Jan 1, 1982

By Johann Knecht

Due to lower specific investment and operating costs the tendency towards large scale equipment will remain. For the design engineers not only the stresses in the mill structure and manufacturing are of importance but also transportation to and erection on site. A scale up of the design of smaller sized units on the pantograph principle may not always give the best approach to the job in this respect. This paper covers recent developments in the design of large size equipment where the huge dimensions call for designs being different to the well known ball and SAG mill concept with cast conical endwalls. The first part describes the features of the biggest ball mill in the world, whereas the second part provides some details of the largest shell supported SAG mills being currently in the manufacturing process.

Jan 1, 1993

By M. Ashraf Mahtab

In Louisiana salt mines a sudden erruption or outburst of salt and gas occurs when the heading face approaches a pressure pocket (altered salt with high pressure gas). The resulting cavity is semi-ellipsoidal, reaching lengths of 50m or more. Potential risks from the outbursts include loss of life and equipment. A gas outburst is initiated by "disking" of the salt in biaxial compression and propagates by spalling of the cavity walls and further disking. The outburst is terminated by a combination of dilatancy hardening, increase in stress along the cavity axis, and enlargement to boundaries of the pressure pocket.

Jan 1, 1982

By John D. Price

The solution to the problem expressed in the title of this paper might well be condensed into one word, AUTOMATON, But if I were to stop there, even though most of you might applaud, I am afraid that a one-word paper might not justify my coming to this meeting, So let?s explore the matter and try to learn if and to what extent the science of automaton can be applied to the problem of coal cleaning. In taking this approach we must, of course, by-pass the fact that plants In this Country and aborad have been automated to a greater or lesser extent. We will explore the matter from the beginning and not merely take the approach that because others have done it we can do it also. First, let us see just what is meant by automaton.

Jan 1, 1959

By E. De Souza

Rockbursts and rockfalls cause very large safety and productivity losses in underground mines. One of the major unsolved problems of safe, economical rock support in underground mining has been that of maintaining anchorage during dynamic rock loading conditions or seismic related occurrences. It is recognized that the large displacements and high strain rates in excavation walls and underground structures cannot be countered by increasing the strength of stiff rock-reinforcing systems but must be accommodated by introducing yieldability into the support elements. This paper introduces a low cost yieldable support system which provides viable solutions to dynamic support loading. Such system should not only provide a feasible and more effective rock mass stabilization strategy but improve mine safety and reduce losses.

Jan 1, 1998

By E. Yan, M. Mankosa, G. Luttrell

"During the past decade, column flotation cells have become widely accepted for upgrading ultrafine sulfide ores. However, the use of columns has been widely relegated to cleaner circuits due to their comparatively high selectivity derived from the use of wash water dispersed over a deep froth. High tonnage rates and low feed grades make using column technology in roughing and scavenger stages challenging due to the resulting size of the needed equipment. To specifically address this challenge, a new high-intensity flotation system known as the StackCell™ was developed. This technology makes use of a novel pre-aeration method coupled with froth washing to simultaneously provide improved flotation kinetics and selectivity. The novel aeration system provides efficient bubble-particle contacting thereby shortening the residence time required for particle collection. This article reviews the technical design features of this new flotation technology and presents recent data from in-plant pilot testing in a copper-sulfide application. INTRODUCTION Column flotation cells have become very popular in the minerals processing industry for cleaner circuits due to their ability to produce a high-grade froth concentrate via the use of froth washing (Luttrell et al., 1999; Kohmuench et al., 2004). The use of wash water minimizes the nonselective recovery of ultrafine impurities that are normally entrained into the froth product from conventional flotation machines. On the other hand, the unique design of a column cell typically requires a large tank volume. Column cells must be tall to ensure that the pulp residence time is long enough to offset their inherently slow flotation kinetics and to minimize internal mixing that is detrimental to overall cell performance. The tall design minimizes the total floor space required for the column installation, but substantially increases the foundation load. The large size of the column tank can also create issues during fabrication, transportation and installation. To address these concerns, the engineering team at Eriez Manufacturing developed a next-generation flotation technology called the StackCell?. This high-intensity flotation machine was designed to provide column-like separation performance within a very compact volumetric footprint. This article describes the key working features of this new technology and provides data from recent pilot-scale tests conducted in gold and copper-sulfide applications"

Jan 1, 2016

By T. P. Meloy

Like our wives, the comminution of brittle solids is easy to recognize but difficult to describe. However, describing it we must. Describing the fracture mechanism of brittle solids permits the eventual mathematical quantification of the results, process optimization and control strategies. This paper presents a physical model of brittle solid comminution that explains why the slope of the log-log size distribution curves have a slope of one or less in the smaller particle sizes. To develop the hypothesis, modifications of the Gaudin Meloy physical model are made. In brittle solids, comminution takes place by cracks propagating through the material. These cracks may bifurcate as they move. Cracks may terminate either on the original surface of the material, or on a secondary crack within the material formed earlier in the comminution process.

Jan 1, 1994

By William C. Peters

"A large proportion of the earth's surface is blanketed by young sedimentary formations and by recent lava flows. How many Guanajuatos lie concealed beneath the rhyolitic capping of the Sierra Madre of Mexico? How many Kirkland Lakes are under the drift cover of the Canadian Shield? How many Wilunas are still hidden by the alluvium of the desert of Western Australia? How many ore deposits lurk underneath the basalt-covered plateaus of the Columbia River region? If erosion at Goldfield, Nevada, had stopped 100 feet higher, probably no ore would have been exposed. How many Goldfields are still awaiting discovery?" --Hugh Exton McKinstry, 1948

Jan 1, 1969

By R. J. Roman

Controlled and uniform distribution of the leach solution to a heap is of primary importance to achieving the desired rate of metal recovery and PLS grade from the heap. The step used to engineer the irrigation system are the same whether drips, wobblers or sprinklers are to be used. The mining rate, leach cycle time and heap height influence the heap cell size which along with the irrigation method selected controls the design of the irrigation system. The steps in the design procedure are explained as are the advantages and disadvantages of each irrigation method.

Jan 1, 1996

By Stephen P. E. Redmond

A 15 km water supply tunnel is being constructed in Buenos Aires, Argentinata expand the capacity of the existing system. Two 4.3 meter diameter Earth Pressure Balance (EPB) tunneling machines operating at times from the same shaft on a congested work site and advancing through sedimentary deposits underlying this wonderful city pose interesting challenges. As of January 1999approximately 50% of the tunnel has been excavated. Combined machine production rates of 1026 m/month have been achieved. Presentations made in prior proceedings can be referenced for details of the overall Project scope and for details of the tendering process. The purpose of this paper is to compliment those presentations by addressing now the execution of the work.

Jan 1, 1999

By J. L. Post

A near-surface body of readily available Na-montmorillonite is located about 24 km (15 miles) southeast of Fallon, NV. The clay, which forms an irregular deposit about 4.8 km (3 miles) long, lies in altered rhyolite within a fault zone. The clay is similar to Wyoming bentonite but is less uniform in composition and contains less MgO and more Fe2O3 in its crystal structure. The clay interlayer cation population can be estimated by using a modified DTA procedure. With selective mining, the industrial properties of the Nevada clay are adequate for use as drilling mud, in foundry applications and as a sealant for hazardous wastes and canals.

Jan 1, 1997

By E. B. Johnson, G. Kjerbol, L. J. Holloway

The Mount Baker Ridge Tunnel is a major improvement of Interstate Route 90 in the State of Washington. The total length of planned underground construction is about 3,400 feet (1,040 m) of which 1,332 feet (406 m) will be constructed by a stacked-drift tunneling method. Sized for vehicular traffic on two levels, the net interior diameter will be 63 feet (19.2 m) requiring an exterior diameter of about 80 feet (24.4 m). The material to be excavated is predominantly stiff clay, and this will be the largest-diameter tunnel ever attempted in soft ground. A construction contract for the stacked-drift tunnel was awarded in late 1982.

Jan 1, 1983

By Gabriel E. Zárate, Juan C. Guzmán

In Chile there are significant amounts of gold in flotation tailings that could be recovered, being heap leaching the most promising alternative. In order to determine the feasibility of treating these tailings by this method, a detailed study is carried out using 4 representative samples. After defining the best conditions an economic evaluation is done for a plant treating 200 tpd, sensibilizing with respect to parameters such us gold price, tailing grade and capital costs. The results show that it is technically feasible treat these gold tailings by heap leaching with gold extractions over 70 %. It is also economically feasible for gold grades higher than 0.5 g/t and gold prices over 350 US/oz.

Jan 1, 1987

By John L. Burnett

Field criteria are needed to help the prospector recognize a potentially expansible shale, clay, or slate. Certain criteria have proven useful in California even though the physical-chemical mechanisms of expansion are not thoroughly understood. Three conditions must be satisfied before expansion can take place, The raw material must partially fuse at a low temperature (1800-2000°F.), Concurrently a gas must form. The raw material must be sufficiently impermeable to trap the gas within the particle. Low temperature melting, which is controlled by bulk chemical composition, is difficult to assess in the field but most common shale, clay, and slate is suitable in this respect, The presence of organic carbon, the most common source of an expanding gas, is indicated by dark color of the rock, A large proportion of clay-sized particles promotes impermeability; fine grain-size is indicated by conchoidal fracture, The shape of the expanded particle is commonly indicated by the texture of the raw material. Rocks with well-developed slatey cleavage produce accordion-shaped particles; massive rocks tend to form rounded particles. Undesirable materials commonly present with expansible shale include: weathered shale; sandstone and other coarse-grained sediments; and limestone, Weathering, which is indicated by color, reduces or eliminates expansion; therefore, surface samples seldom are representative of the shale found at depth. Sandstone does not expand and will increase the average weight of the finished product, Limestone or particles of carbonate minerals can be actively harmful because they are converted to free lime (CaO) during the firing process, If free lime is present in concrete, hydration will cause expansion of the lime particles which result in surficial ?popouts.?

Jan 1, 1963

By Denis McDermott

This paper describes the process used at three mines to devel­op safety and training programs. The mines are located in Australia, New Zealand and the United States of America. The aims of the programs were to promote and reinforce safe and healthy behaviour, increase productivity and efficiency and to provide a fair and objective basis for the payment of wages. There were common aspects to each of the projects: • mandatory legislation required employers to provide employ­ee training in work performance • employees had little previous involvement in the design and development of the training provided • training had been unstructured with employees relying on the "buddy system" to acquire new skills; the degree of skill acquired by an employee depended on the knowledge and teach­ing capacity of the worker to whom the novice was assigned • appointments and promotions had been based on judgements by supervisors and these were not generally understood by employees • employment conditions for employees were covered by an industrial agreement between management, unions and employ­ees. The degree of sophistication of the industrial agreements varied however none provided a description of work performed in each classification, nor the career or promotional path for an individual • supervisors with the responsibility to train, develop, motivate and reward employees expressed concern that there were no structured processes ( eg work standards or wage progression cri­teria) to support their role.

Jan 1, 1998

By AMIR EHSAN KIANFAR, Moritz Ziegler, TOBIAS HARTMANN, ELISABETH CLAUSEN

Accurate positioning information is a central step in the process of increasing automation and digitalization in the mining industry. Underground mine environments are prime examples for GNSS-denied environments that pose several additional challenges for the employed indoor positioning system (IPS). This work presents an ultra-wideband (UWB)- based system specifically tailored for underground mine environments. Initially, the UWB technology is reviewed and basic concepts of IPS are explained. Both software and hardware are described in detail, including positioning algorithms, electrical circuitry and the mining-compatible enclosure. Finally, the results from field tests in an underground mine are presented and positioning performance and the influence of dilution of precision (DOP) on positioning results are empirically evaluated. The results show that the localization errors are mostly below 1 m. Individual zones of high localization errors are suspected to be caused by noise interference. Significant DOP influence due to the mining drift geometry can be confirmed. The system shows promising localization results for different mining applications, while influences negatively impacting the accuracy are presented as items for future research.

Jan 1, 2024