Search Documents

By Z. Manafi

Bioleaching of a copper sulfide ore containing "activated pyrite", using a mixed culture of mesophilic bacteria, was studied. This type of copper ore had been found unsuitable for flotation because it produces a concentrate containing relatively high iron concentrations and, therefore, a low copper grade. Microscopic observations showed that pyrite particles had been activated by the formation of a thin film of chalcocite. Hence, a bioleaching process was considered as an alternative to treat this ore. Following shake flask and acid consumption tests, column tests of the crushed ore (75% -12.5 mm) were initiated and the effects of culture medium, agglomeration, and irrigation type on copper recovery were studied. The results showed that all the columns containing bacteria had copper recoveries around 90% compared to the abiotic control column with a recovery of 50%. It was concluded that bioleaching could be successfully utilized to process copper ores containing activated pyrite.

Jan 1, 2007

By P. Hickey, A. Oliver

"In March 1993, Ram Raising Limited was faced with a challenge. Placer Dome Incorporated, Dome Mine Division requested from Ram Raising that they design station excavation into the existing No. 8 shaft from No. 3 mine levels. This work had to be done without loss of production time in the underground department.Due to the time frame of the project, every detail had to be carefully considered, with extra care that all pros and cons had been worked out.Ram Raising submitted a work Plan that had been worked out with the Redpath Group which included the infrastructure requirements; the engineering design; the scheduling and sequence of work; and the excavation design and blasting procedures.A proposal was' put together by both Ram Raising and Placer Dome outlining the infrastructure requirements, including the engineering design, scheduling and sequence of the work, excavation design and blasting procedures. The proposal accepted by Placer Dome and, on July 3D, 1993 work commenced to breakthrough eight stations. Work continued until December 1993 with the completion off our stations. The project was then stopped to allow the station access drifts from No.3 mine to be completed. The second phase of the project began on May 27 and was completed on September 15, 1994.This paper shows how, through innovative design and the full cooperation between client and contractor, a project of this nature can be completed successfully."

Jan 1, 1995

"This document sets out the Exchange’s expectations and requirements for a valuation of mineral properties and outlines: the general purpose of valuation reports; guidelines respecting circumstances where the Exchange will require a valuation report; and valuation standards, guidelines and methods that are generally acceptable to the Exchange, 1. IntroductionThis Appendix sets out the Exchange's expectations and requirements for a valuation of mineral properties and outlines:(a) the general purpose of valuation reports;(b) guidelines respecting circumstances where the Exchange will require a valuation report; and(c) valuation standards, guidelines and methods that are generally acceptable to the Exchange.Mining industry standards and guidelines for valuations and valuation reports can be found in the Canadian Institute of Mining, Metallurgy and Petroleum Standards and Guidelines for Valuation of Mineral Properties (""CIMVal"") published in February, 2003 (www.cim.org). CIMVal consists of two parts, Standards and Guidelines. The Standards are mandatory and must be followed in order for a valuation to be CIMVal compliant. The Guidelines in CIMVal are not mandatory, but are strongly recommended.The Exchange requires that CIMVal Standards be used by Issuers and their professional advisors when preparing valuations and valuation reports on mineral properties. The CIMVal Guidelines should be followed by Issuers and their professional advisors in preparing valuation reports on mineral properties, with the exception that the valuation methods and guidelines under Section 4 Acceptable Valuation Methods and Guidelines below, must be followed."

Jan 1, 2003

By K. Soldenhoff

Mantra Resources Ltd is developing the Mkuju River project is southern Tanzania. The uranium deposit, hosted in ?Karoo? sandstone, is surface outcropping with the majority of uranium mineralisation occurring in the finer clay component of the ore. A flowsheet, consisting of ore beneficiation, acid leaching, RIP uranium recovery and direct precipitation of the uranium product, was developed and successfully demonstrated in continuous mini-plant operations at ANSTO. The selected flowsheet overcomes the difficult slurry rheology, arising from the clay component of the ore, by eliminating the need for a CCD plant. The RIP process was found to contribute to a high uranium extraction, by eliminating ?preg-robbing?, at a relatively low acid addition in leach, with the potential to eliminate ferric ion and oxidant additions.

Aug 1, 2010

By David Deglon, Martin Harris, Mehdi Safari

"This study investigates the effect of energy/power input on the flotation of a platinum ore in a pilot-scale oscillating grid flotation cell. Oscillating grids generate near ideal hydrodynamic environments, characterised by turbulence which is relatively homogeneous and isotropic. Secondary rougher feed and primary cleaner tail streams were floated in a pilot-scale oscillating grid flotation cell at power inputs from 0 to 2.5 W/kg, using 0.50 and 1.50 mm bubbles. From this study one may conclude that the effect of energy/power input on the flotation rate is strongly dependent on the particle and bubble size. Flotation rates generally increase with increasing particle size and decreasing bubble size. Increasing energy input generally leads to an increase in the flotation rate for finer particles and an optimum flotation rate for intermediate & coarse particles. Optimum conditions for intermediate/coarse platinum ore particles are using small bubbles at low energy inputs, or large bubbles at higher energy inputs. These results suggest that higher energy inputs are generally beneficial for the flotation of platinum ores as these consist predominantly of finer particles (-75 µm) and most industrial flotation applications operate with larger bubbles (1.0-2.0 mm).INTRODUCTIONThere is a considerable body of experimental and theoretical evidence to suggest that energy/power input plays an important role in flotation kinetics, particularly in the finer particle sizes where flotation efficiency is poor (Deglon, 2005). A number of excellent studies into the effect of energy on flotation kinetics have been carried out in impeller stirred cells (Ahmed and Jameson, 1985; Deglon, 2002; Pyke et al., 2003; Newell and Grano, 2006). Investigations using this type of cell have a number of limitations. The impeller influences particle suspension, bubble break-up and agitation in the cell. In addition, turbulence is highly inhomogeneous and anisotropic, with power intensities near the impeller orders of magnitude higher than those found elsewhere in the cell (Deglon, 1998; Koh and Schwarz, 2003; Schubert, 1999, 2008). These limitations have resulted in the development of novel cells for the investigation of energy input."

Jan 1, 2016

Arguably the SMC Test® has become the most popular laboratory hardness test in the world with over 17,000 tests having been completed to date, covering over 650 different ore bodies. It is now routinely used in design, optimisation and orebody profiling projects. The test is unique in that from relatively small amounts of drill core it simultaneously provides parameters that are used in simulation modelling of AG/SAG and crushing circuits as well as work indices that are used in power-based equations for predicting the specific energies of AG/SAG/Crushing and HPGR circuits. The very large data base that has been accumulated has provided the opportunity to study the differences in variability from deposit to deposit. This paper describes and discusses the trends that have become apparent from the study of this data base. Recommendations for appropriate selection of sample numbers are also made which are based on these trends.

Jan 1, 2012

By R. J. McLeod

"Grinding at Giant Yellowknife is done in two stages. The first stage consists of two ball mills in closed circuit will: mechanical classifiers, the classifier overflow goes to flotation. The tailings from this flotation circuit are separated into slime and sand portions, the slimes go to an additional flotation circuit while the sand portion goes to the secondary grinding mills.Milltronic automatic sound control units were installed on each of the two primary ball mills and put into operation September 3, 1966. After about two months adjustments to the control units the operators were taken off the grinding circuit on November 1, 1966. The operators duties were taken over by the automatic control units while miscellaneous work was taken over by the helpers in the mill. The labour saving by the installation is approximately $2250.00 per month.After a short period of operation it was apparent there was a slight change in grind. The screen analysis of the primary classifier overflows for the period May to August 1966 averaged 62.23% minus 200 mesh while for the period September to December 1966 averaged 62.0% minus 200 mesh. This is a slight coarsening of the grind. The change in the primary grind has manifested itself also in the screen analysis of the final grind. Before automation the final grind was 80% minus 200 mesh, while after automation it was 7 5% minus 200 mesh. A change of grind was also noted in the flotation concentrates. Before automation the screen analysis of the concentrates was 35% plus 200 mesh and 50% minus 3 25 mesh. A ft er automation it was 35% plus 200 mesh and 47 .5% minus 325 mesh. In other words the grind got coarser or perhaps we should say there was less overgrinding. Another significant change took place in the assays of the slime and sand portion of the primary flotation tailings. It was usual under manual control for the slime portion to assay higher in gold than the sand portion. The reverse is now true."

Jan 1, 1967

By Jeff Bird, Xijia Wu, Prakash C. Patnaik

"Prognosis and health management (PHM) is an evolving suite of technologies intended for application to the life cycle management (LCM) of mission/safety critical systems, with anticipated results, which will: - Reduce life cycle cost - Enhance operational safety and readiness - Assist in maintenance decision-making - Enable autonomic logistics While it is emphasized in the United States that future multi-mission fighter aircraft such as Joint Strike Fighter (JSF) must have PHM capabilities, Canadian initiatives also recognize the need to implement such schemes for future and legacy military and civil aerospace systems. With respect to four major technology areas of PHM, i.e., i) advanced sensors, ii) data analysis and fusion, iii) life consumption evaluation, and iv) predictions with reliability/risk assessment, there has been advanced technologies developed by NRC and others within Canada: - Aircraft/engine instrumentation and airborne data recording systems - Signal analysis and data fusion - On-line engine health monitoring - Physics based models for engine material failure modes and life prediction - Autonomic crack growth analysis for damage tolerance of engine components - Mission severity analysis algorithm - Probability, reliability and risk assessment This presentation reviews the above technologies in relevance to PHM, emphasizes the need to have physics based models and outlines the future R&D needs for integration and implementation of these technologies suitable for the advanced and legacy aircraft."

Jan 1, 2004

By J. W. Hendry

"This paper will discuss the application of tools and the evolution of computer-assisted procedures in the production planning process at Quintett e Coal Limited (QCL). In 1986, QCL produced 5.3 Mt of clean coal from their surface mining operation located in north eastern British Columbia. The structural complexity of the sedimentary deposit and high rate of mining necessitate the consideration of large amounts of geological information which continually updates the interpretation. There are multiple unit operations required during the process of mining through a given multi-seam sequence, which results in many interdependent faces, and multiple iterations of scheduling sequences in order to satisfy a given set of objectives. In order to facilitate these activities in a timely fashion, it was recognized that a computer systems' capability needed to be developed which could increase the efficiency of information input, manipulation and output. IntroductionQuintette Coal Limited (QCL) has been operating a large metallurgical open pit coal mine in northeastern British Columbia, since 1982. The mine produced 5.3 Mt of clean coal in 1986 for export to Japan. Throughout the start-up period and the subsequent build -up of production levels, it became evident that the primary producing area was comprised of extremely complex faulted structures. This has resulted in development and modification of specialized mining methods employed to effectively recover the resource. Similarly, the planning and engineering techniques employed have been evolved over the same period of time. The implementation of computerized methods has been one of the major developments in this process, including geology interpretation, modelling, reserve definition, quantification, production planning and scheduling, and graphical plan presentation. These capabilities have been employed, in various forms, for project scale feasibility work and long range planning for some time, however, the use of computer tools for short-term, detailed production planning of a complex mining environment presents a different set of problems. It is hoped that a presentation of the current state of evolution and future plan s for development will be of interest to organizations considering implementation of a similar system."

Jan 1, 1988

By G. Roy

Interest in metal-hydrogen systems can be manifold. Small amounts of hydrogen adsorbed by elemental metals and alloys usually result in strong changes in the physical and mechanical properties of engineering materials. Overwhelmingly, these changes, viz. hydrogen embrittlement, are considered deleterious with respect to structural performance of engineering materials. However, the changes, often studied by metallurgists and metal physicists, can present new possibilities and applications. A prominent example is the recent interest in safe, solid-state hydrogen storage in metallic lattices. In a new laboratory in MTL, Ottawa, a study has been initiated to investigate the effect of "micro- and macro- alloying" of Al and Mg powders with hydrogen (in high-energy mechanical alloying mills) on plastic deformation in metal and metal hydride structures. It is anticipated that high-rate impacting and subsequent grain refinement in the mill will have an effect on hydrogen storage capacity in lightweight magnesium and aluminum alloys. First examination of the state-of-stress by X-ray diffraction in high-rate milled, nanostructured pure aluminum, aluminum milled with a solid surfactant, and aluminum or magnesium alloy milled with hydride and/or gas hydrogen will be presented.

Jan 1, 2005

By I. Takahashi

Recently, electronic devices have become smaller for some kinds of electronic devices, thermal dissipation and electrical conductivity of conventional Fe based alloy becomes insufficient. We selected the Cu-Fe based alloy CDA19400 and optimized the wire manufacturing process. Precipitates during aging treatment were observed by TEM. The size and distribution of the precipitates varied according to solution treatment temperature. With solution treatment at 950°C, the precipitates of y-Fe as fine as 10 nm were distributed dense in the copper matrix with coherency. For the solution treatment at 750°C, y-Fe of approximately 200 nm was observed. Comparing heat resistance of drawn wires, the material at 950°C treatment was superior. Electrical conductivity decreased from 63% IACS upon aging to 29% IACS by drawing. It is considered as particular phenomena for wires where materials are drawn with high reduction ratio. By the optimized manufacturing process, we successfully developed a new wire that has superior in strength, thermal conductivity, electrical conductivity, heat resistance and repeated bendability.

Jan 1, 2007

By Young C. Kim

A proper economic analysis of pit slope design must reflect the trade-off between the benefits and the increased risk of slope failure inherent in steeper slope angles. However, no formal framework for a proper analysis has existed to date. This paper summarizes the material contained in the Design Chapter Supplement (5-3) of the Pit Slope Manual. The supplement describes the results of the research effort in which a formal economic analysis framework was developed and tested through a case study. The case study results have demonstrated the practicality of the developed procedure and the availability of required data under "real-life" conditions.

Jan 1, 1979

By Fathi Habashi

New technology first introduced by Nippon Steel Corporation at Kitakyushu in Japan in 1976 now used at a number of plants in other countries, known as dry quenching of coke, uses nitrogen in a closed circuit to avoid environmental emissions. In addition, heat is recovered in the form of steam, from the red-hot coke. In steel plants oxygen is used extensively and therefore by-product nitrogen from air liquefaction can be effectively utilized in this way.

Jan 1, 2014

Agenda 1.Energy consumption and energy costs ?focus and failings 2.Energy efficiency methodologies, people and supporting tools 3.Energy cost saving case studies from three minerals processing plants 4.The operations team and the supporting role of Operations IT 5.Conclusion: Reducing energy consumption and energy costs There are many good Energy Efficiency Methodologies ?Energy and GHG Emissions, Management Guidance Document, The Mining Association of Canada ?Energy Savings Toolbox ?An Energy Audit Manual and Tool, Canadian Industry Program for Energy Conservation (CIPEC) ?Lean and Energy Toolkit, Achieving Process Excellence Using Less Energy, www.epa.gov/lean ?Energy Efficiency Opportunities Assessment Handbook, www.energyefficiencyopportunities.gov.au

May 1, 2010

By Jin Li

The tensile properties and microstructure of AZ91 Mg alloy before and after equal channel angular extrusion (ECAE), and the fracture behavior during tensile testing for as-extrusion and ECAE AZ91 were investigated. The alloy was performed ECAE from one to eight passes at 498K. The elongation decreased with the pass number increasing after ECAE. Grains were refined, partial coarse ß-Mg17Al12 phase fell to pieces, fine ß-Mg17Al12 precipitated in the AZ91 Mg alloy after ECAE. During tensile test the a-Mg/ ß-Mg17Al12, a-Mg/Al8Mn5 interface and the grain boundaries in a-Mg matrix acted as the crack initiation sources. The frequency of micro-cracks at the a-Mg/ß-Mg17Al12 interfaces and grain boundaries increased after ECAE, which accelerated the growth and coalescence of the micro-cracks during tensile test and resulted in the decrease of elongation of AZ91 Mg alloy by ECAE.

Jan 1, 2006

By Daniel B. Leznoff

The cyanoaurate anions [Au(CN)2]- and [Au(CN)4]- are shown to be useful building blocks for synthesizing supramolecular coordination polymers. For the gold(I) unit, aurophilic interactions often increase the structural dimensionality of the system and can impart increased thermal stability to the metal-polymers produced. A series of polymers of the form M[Au(CN)2]2(Ligand)x have also been prepared and show large colour changes upon changing the ligand, thus illustrating a sensor-type application. Both building blocks can mediate significant antiferromagnetic and ferromagnetic interactions between transition-metal centres in the polymers. For the gold(III) unit, no metal-metal interactions are observed, although weak Au-N(cyano) interactions control the intermolecular packing. Several structural examples of cyanoaurate-based coordination polymers are presented, including 2-D and 3-D arrays and a supramolecular square.

Oct 1, 2003

By L. Contretras

This study has as an objective to analyze and to propose actions to improve the quantity and quality of the graduate education in the area of mining industry, specifically of mining engineers, metallurgists, geologists, to satisfy the expectations of professionals in the mining industry. Included are an analysis of the present scenario and the future demands in countries like Chile and proposed plans for the Establishment of Educational Initiatives, country policies and market forecast, vis-a-vis the experience of Australia, South Africa, United Kingdom, Canada and the United States of America.

Jan 1, 2007

By BARRY BANNATYNE

About 90 per cent of Manitoba's industrial minerals production is for structural materials. Most of these come from the Paleozoic rocks west of the Precarnbrian Shield, or from glacial deposits that are extensive throughout Manitoba. The major raw materials are sand and gravel, and carbonate rocks for crushed stone (and also dolomite for high-magnesia lime, high-calcium limestone for lime and Portland cement, and dolomitic limestone for Tyndall stone). Glacial lake clays are used both in cement and in lightweight aggregate. The Jurassic and Cretaceous strata exposed along or near the Manitoba Escarpment include siliceous, carbonaceous, kaolinitic and illitic shales, all of which are quarried by Red River Brick and Tile in the Pembina Mountain and Ste. Rose areas for use in a brick plant at Lockport. Non-swelling bentonite near the base of the Pembina Member of the Upper Cretaceous Vermilion River Formation is of value as an absorbent clay, and is the only commercial source in production in Canada. It has been quarried by Pembina Mountain Clays Limited since 1940. Gypsum occurs in the Jurassic Amaranth Formation and supplies much of the market for wallboard and Portland cement additive in the Prairie Provinces. Quarries are operated at Gypsumville by Domtar Construction Materials Limited, and north of Amaranth by Westroc Industries Limited. Silica sand from the Ordovician Winnipeg Formation is of glass-grade quality, and about 100,000 tonnes are produced annually by Steel Brothers Canada Limited on Black Island . It is used as a glass sand, as foundry sand, for sand blasting, and as a filter-bed sand .

Jan 1, 1984

By D. MacGREGOR, VERA TUREK

The St. Canul and Ste. Scholastique orthoquartzite sanrjstone deposits are located within the Potsdam Formation near Montreal. The sandstone lies on Precambrian basement and is Cam/3rian to Ordovician in age. The Potsdam Formation shows two distinct stages of development. One created a deepwater facies represented by impure, limey or shaley sandstone; the other produced a shallow facies composed of grey, highpurity sandstone. The shallow-water orthoquartzitic sandstone at St. Canul is being mined and beneficiated by lndusmin Limited. The operation manufactures a wide range of silica products and supplies industrial areas of Quebec and Ontario with material for the glass, foundry, silicon carbide and ceramic industries.

Jan 1, 1984

By Z. S. Abisheva

The Zhezkazgan copper sulfide ore deposit in Kazakhstan contains both rhenium and the rare osmium isotope "osmium-187" (187Os) in the high isotopic purity of 99.4 ± 0.2%. This isotope is believed to have originated as a result of the disintegration of one of the rhenium isotopes, according to the reaction: 187Re75 ?> 1870576 + B- + v~ (where B is a 13-particle, v~ is a 3-disintegration antineutrino). The distribution of osmium and rhenium in metallurgical byproducts produced during the recovery of copper from these ores has been studied and process flowsheets for the processing of rhenium and osmium-containing byproducts have been developed.

Jan 1, 2007