Search Documents

By Richard M. Crowell

"As thorough sampling is usually expensive, the cost of a complete job is often unwarranted, and a cheaper approximation must be substituted. The engineer should, however, weigh the situation thoroughly before subscribing to an alternative other than an accurate assay basis on which to build his conclusion." Examination and Valuation of Mineral Property. R. Parks, 1949

Jan 1, 1994

By M. Sinirkaya

The dissolution process of phosphate rock from the Semikan area (Mardin-Mazidagi, Turkey) using dilute phosphoric acid has been investigated. The work involved studying the effect of important variables, such as reaction time, stirring speed, particle size fraction, phosphoric acid concentration and temperature. Van der Sluis et al.?s model was used to determine the rate of the partial dissolution of phosphate ore. Mass-transfer coefficients (kL) varied between 2.8 and 28.5.10-3 m.s-1. The activation energy of the process varied between 16 and 20 kJ.mol-1. It has been found that the dissolution process is controlled by calcium ion diffusion, rather than by chemical reaction.

Jan 1, 2010

By Sanja Zlatanic, Michael P. Della Posta

New York State’s Metropolitan Transportation Authority (MTA) has undertaken the largest transportation project in New York City. The East Side Access Project (ESA) will introduce MTA’s Long Island Rail Road (LIRR) service to the East Side of Manhattan, to a new terminal located beneath the existing, landmark Grand Central Terminal(GCT). Construction of the Manhattan Segment of the project will affect overlying operating facilities of two other MTA entities, Metro-North Railroad (MNR) and New York City Transit (NYCT) and major Midtown Manhattan buildings. The paper describes the evolution of the GCT concept at Manhattan from a shallow alternative proposed by a Major Investment Study (MIS), that would require extensive underpinning of multi-story buildings and have considerable impact on MNR and NYCT operations, to a deep alternative with lesser risk and potential for disruption.

Jan 1, 2001

By Erik S. Bernard

"INTRODUCTION Reinforced Concrete (RC) members such as beams and columns are usually required to include stirrups to maintain post-crack shear capacity, and some may include stirrups that act as confining steel to maintain structural integrity during a seismic event (eg. NZS3101, ACI 318). To achieve seismic resistance, the spacing between stirrups is usually required to be much closer than is ordinarily prescribed for non-seismically resistant structures. Each stirrup must also fully enclose the longitudinal reinforcement with long end-hooks to ensure that the contained concrete is sufficiently restrained during reverse-cycle loading and the reinforcing bars are confined to prevent buckling. The close spacing between stirrups can lead to congestion of reinforcement within members, and can also be expensive to construct due to the labor-intensive nature of steel fixing. A possible alternative to closely-spaced stirrups is the use of fibers to provide restraint and confinement during a seismic event, although this is not yet recognized in codes. Previous experimental research (Jiuru et al, 1992; Filiatrault et al, 1995; Bayasi and Gebman, 2002; Billington and Yoon, 2004) has demonstrated that steel fibers are relatively effective in this application, but suffer the problem that their stiffness can make them difficult to consolidate within an already tight reinforcement cage, especially if they are relatively long (>40 mm). Moreover, steel fiber reinforced concrete (SFRC) is subject to embrittlement with the passage of time, leading to a steady loss of ductility beyond crack widths of 1-2 mm (Banthia and Trottier, 1994; Bernard and Hanke, 2002; Bernard, 2014; Bjontegaard et al, 2014; Bernard, 2015). Since cracks during seismic events are generally much larger than this, embrittlement may present a challenge to the long-term efficacy of SFRC during seismic events. An alternative to steel fibers for enhancement of seismic resistance is the use of macro-synthetic fibers. This type of fiber usually offers the advantage of being flexible so that consolidation is easier between reinforcing bars. They also offer superior durability compared to steel fibers and can reduce flexural crack widths (Bernard, 2016). Several recent small-scale investigations (Ma et al, 2012; Carnovale, 2012; Osorio et al, 2014) have indicated that macro-synthetic fibers can produce meaningful improvements in seismic resistance if used in combination with conventional steel reinforcing bars. The present investigation has extended research in this field by examining whether embossed macro-synthetic fibers can be used to increase the spacing between stirrups while maintaining seismic resistance."

Jan 1, 2016

By T. McCallum, C. Cooper, C. Lewis

"Following a successful solvent extraction (SX) pilot plant demonstration in 2016, CYANEX® 600 has been used commercially to recover molybdenum from concentrate leach liquor since March 2017. Consistent with the piloting results, the commercial plant has achieved expected molybdenum recovery, a significant reduction in base consumption, and a step-change improvement in physical performance. This paper highlights the optimization activities and plant performance from startup through normal operation. INTRODUCTION Historically, tertiary amines have been the most commonly used extractant for molybdenum and rhenium recovery. Tertiary amines utilize a protonation of the ligand combined with an anion exchange mechanism as proposed in equations (1-2). R3N + H+ ???R3NH + (1) 4R3NH+ + Mo8O264- ???(R3NH+)4Mo8O264- (2) In addition to the transfer of Mo and Re, the amine transfers acid and other anions to the strip liquor. The undesirable transfer of other species increases base consumption during stripping, impacting operating costs. Additionally, lower solubility of molybdenum-amine complexes create operational challenges, resulting in diminished physical performance. The presence of colloidal Si in concentrate leach liquors and the formation of Pickering Emulsions adds to the physical plant performance challenges with the amine extractant. CYANEX® 600, a phosphinic acid-based extractant, uses a cation exchange mechanism proposed by equation (3). 2(H2R2) + MoO22+ ??(HR2)2MoO2 + 2H+ (3) The cationic exchange mechanism eliminates chemical transfer of acid and other anionic impurities and avoids some of the physical challenges of the amine extractant (emulsion and 3rd phase formation). In addition, the reagent offers high selectivity for Mo over Re, which may be desirable in certain moly pressure oxidation (POX) flowsheets. Alkali base (ammonium hydroxide, sodium hydroxide, sodium carbonate, etc.) is used for molybdenum stripping. Therefore, reduction or elimination of chemical acid transfer from extract can significantly reduce base consumption in strip. Extensive laboratory and pilot plant testing was completed to evaluate the use of CYANEX® 600 for molybdenum recovery at Freeport-McMoRan’s Bagdad operation. The test work and pilot demonstration confirmed a reduction in base consumption along with improved selectivity. In addition, the evaluation highlighted a step-change improvement in physical performance over the incumbent amine extractant. The decision was made to convert the commercial operation to CYANEX® 600 in March 2017."

Jan 1, 2018

By Leland L. Mink

Open-pit mining is sometimes conducted in areas where the artesian pressures contained in aquifers underlying the pit's floor are great enough to cause floor heave. In order to reduce this pressure several methods are commonly used. One of these methods is a pressure relief well or depressurization wick. The wick consists of a borehole which is filled with gravel and cased at the surface. The wick is allowed to flow freely, thus reducing pressure near its location. The spacing and depth of these wicks can be determined by a simple analytical and graphical technique which considers the weight of material overlying the aquifer and the artesian force within the aquifer. An example of the technique using data from a Colombian coal mine is presented.

Jan 1, 1986

By B. Qiu, Y. Luo

Longwall and/or room-and-pillar mining operations in multiple coal seams may not only induce subsurface and surface subsidence but also cause interactions between these mined coal seams. The interaction might destabilize underground mine structures and subsequently induce additional strata movements. Mathematical models to use the predicted subsurface deformations to assess the interactions and the consequences have been developed. The models are incorporated into a computer program, CISPM-MS, for predicting the final surface movements and deformations, as well as the mining interactions associated with multiseam coal mining operations. It predicts final surface movements and deformations caused by the individual mining operations and by the interactive effects. The program can also be used to assess mine structural stability in multiseam mining operations. The paper presents the developed interaction models and their application in surface subsidence prediction caused by multiseam mining operations. A case study involving mining in two coal seams, using longwall and room-and-pillar mining methods, respectively, will be used to validate the program.

Jan 1, 2013

By Richard Thomas Newcomb

The trend towards proportionately rising volumes of surface mining through- out the world and especially in the United States has led some observers to predict that the future of underground mining is quite limited. Certainly, the simple extrapolation of current trends1 gives evidence of a compelling sort for the hypothesis that technological progress is proceeding at a faster pace in surface than in underground mining. This paper attempts to examine the basis for these predictions by searching the historical record on differential rates of productivity as these are observed in iron ore and coal mining. In recent years economists have discussed "technology gaps" among industries or segments of the same industry, by which they mean that mechanisms for invention and its diffusion are faulty or retarded in such a way that feasible cost-cutting innovations are not applied or developed, even though technicians regard them as practical.2

Jan 1, 1968

By C. K. Arthur, N. K. Dumakor-Dupey, B. A. Kansake, F. A. Kaba

Autonomous mining systems have been deployed for improving mine performance. However, there is a fear of job losses. Adoption of autonomous systems is envisaged to be resisted by major stakeholders in Ghana due to high illiteracy and unemployment. This paper assesses the preparedness of Ghanaian mining stakeholders for the adoption of autonomous systems to Ghana’s surface mining industry. Closed and open-ended questionnaires were administered to mine stakeholders. Respondents generally expressed unwillingness to accept autonomous systems into Ghanaian mines due to fear of increased unemployment. We propose setting up a mining education fund (MEF) for training stakeholders in autonomous mining systems. INTRODUCTION Mining contributes enormously to the sustenance and growth of global and national economies through the provision of raw materials, employment, revenues and foreign exchange (Carvalho, 2017; ICMM, 2017; Cordes et al., 2016; Solomon et al., 2008; Walser, 2000). The International Council on Mining & Metals (ICMM, 2014) reported that globally, formal mining employs approximately 2.5 million people. Many resource-rich countries, especially the developing ones, have experienced strong socioeconomic growth propelled by the discovery and extraction of valuable minerals. McMahon and Moreira (2014) reported a positive linkage between mining and sustainable development. They revealed that averagely, resource-rich countries have improved Human Development Index (HDI) scores than countries without mineral resources. Mining remains a crucial industry in Ghana’s economic development (Bermúdez-Lugo, 2016; Amponsah-Tawiah and Dartey-Baah, 2011). Over the years, mining has contributed significantly to the gross domestic product (GDP) of Ghana. In 2013, mining accounted for 1.7% of Ghana’s GDP and about 19% of government revenues (Ghana Chamber of Mines, 2015). The Ghana Chamber of Mines also reported that mining contributed over 50% of foreign direct investment, 37% of export earnings and 1.1% of direct employment revenues. The US Department of Energy (DOE) estimates that 65% of coal, 92% of metals and 96% of industrial minerals are mined using surface mining methods (DOE, 2007). Generally, mining is a capital-intensive venture, with high operating cost, hence there is a constant demand for mining companies to seek efficient cost reduction and production maximization strategies. One strategy being pursued keenly is automation, which is noted to improve productivity, and worker safety at minimal cost. According to Parreira (2013), mining automation involves direct teleoperation whereby workers remotely control the mining process using computers from a control room.

Jan 1, 2019

By Patrizia Pereyra, M. Guzman, C. Toledo, J. A. Rau, A. Ruiz

The use of mining tailings-based geopolymer binder as a substitute for cement can be an interesting alternative to the problem of final disposing of large volumes of them. Indeed, mining tailings have a high silica content, which makes them suitable for geopolymerization. The tailings samples contain Cu, Pb, Zn, As, Sb, Cd and Bi, mainly. X-ray diffraction results show that the tailings are composed of quartz, SiO2 (81%). Geopolymerized tailing samples (GTPS) were obtained by varying the ratio of SiO2/ Al2O3 and SiO2/NaOH. The compressive strength of the GTPS varied between 2 MPa and 8 MPa. The electrical conductivity in the leaching tests varies between 13.91– 16.11 mS/cm2 indicating that ions are present in the solution. However, the pH = 10.5 indicates that acidity is not being generated. The element that mostly leaches is iron. The highest percentage of leaching is observed for cadmium (69%) and chromium (93%). The concentrations of elements are under the maximum permissible limits for water according to the Peruvian legislation. However, mass transfer leach tests and immersion leach tests must be realized.

Feb 1, 2024

The knowledge of aggregate size under various chemical and hydrodynamic conditions is very important for selective agglomeration, flotation and water clarification processes. Traditionally, aggregate size measurements are conducted using an ex-situ technique or in a diluted suspension. In either case, the measurement occurs in an environment that does not resemble the actual conditions under which the aggregates are formed. In this study, an on-line scanning laser microscope has been used to study the coagula size of micronized coal suspensions as a function of pH, solids concentration and agitation intensity. A maximum aggregate size of 310 µ m was obtained under relatively quiescent conditions and at pH values near the iso-electric point (iep) of the coal. The aggregate size results compare well with the coagulation efficiency measurements obtained under the same pH conditions.

Jan 1, 1994

By J. Wiebmer

Some thoroughbred racehorses are great routers (distance runners), others are sprinters. Some racehorses perform best on turf, others on dirt, and some in mud. To be a winner, you have to choose the right horse for the course. It's no different when looking at an electric cable shovel, a hydraulic shovel/excavator, or a wheel loader. Each loading tool has its own zone of application. To be a winner, you have to choose the right horse for your course.

Jan 1, 1993

By Edoardo Misano, Magali Schivre, Martino Semeraro, Alain Bochon

"INTRODUCTIONThe Laboratoire Souterrain de Modane (LSM) is an underground research laboratory located in the Western Alps on the French – Italian border. It is located in the middle of the 13km long Fréjus highway tunnel that links Modane (France) to Bardonecchia (Italy) in correspondence of the highest overburden of 1800m. The LSM current activity is mainly based on the investigations about the dark matter and requires very sensitive instrumentation which shall be protected from cosmic rays. To comply with the new legislation about safety in tunnels, the highway tunnels owners agreed in 2007 the construction of a parallel safety tunnel, at an average distance of 50m from the existing tunnel and the laboratory owner CNRS (Centre National de recherche scientifique) also decided to extend the existing laboratory with the construction of a new 17000 m3 cavern allowing the installation of wider and more powerful instruments that could increase chances of success of research. Preliminary studies stated that, considering both geological and functional issues, the most appropriate location for the new laboratory shall be in between the two tunnels and parallel to the existing laboratory (see Figure 1).Hence, the CNRS asked Systra, already in charge of the works supervision of the safety tunnel, to realize the design of the new cavern. The laboratory extension includes the construction of a 40 m long cavern with 300 m² cross section and two smaller tunnels connecting the safety tunnel and the existing laboratory to the new cavern. The minimum distance between the front face of the new LSM and the highway tunnel is about 25 m.The French and the Italian authorities, responsible of the exploitation of the Fréjus highway tunnel, asked the CNRS to develop an accurate study indicating that the construction of the laboratory extension would not have any negative impact on the existing structures of the highway tunnel. The main results of the developed study by Systra are summarized hereafter. The construction works should begin prior to the end of the construction works of the Fréjus safety tunnel in 2018."

Jan 1, 2016

By Bo R. Arvidson

The strongest magnetic roll separator available on the market enhances certain industrial minerals purity to levels not reached previously. Exceptionally strong forces can also be utilized for processing relatively fine particles at feed rates several times greater than for prior art electromagnetic induced roll separators. Since the unique machine does not work with an air-gap, coarser particles than what has been considered practical can be separated at rates up to 20 tph per single machine unit and 40 tph for a double machine unit. Examples for all these three application areas will be given. While the roll separator can be used only for dry processing presently, the other new separator can be used for both wet and dry applications. It is a medium-intensity, high- gradient magnetic separator employing a filamentary matrix. It was primarily developed for recovery of weakly magnetic iron ore fines, but it is finding applications for cleaning of industrial minerals such as wollastonite, calcite, clay and talc. Its main advantage is a simple design resulting in a very lm cost machine both with regards to total capital investment and operation. A significant technical advantage exists also. The metallurgical performance is similar to conventional electromagnetic separators, while the cost per ton is about half of such separators.

Jan 1, 1985

By Bahaa Alyosif, Murat Erdemoğlu, Muhammet Kürşat Aydemir, Turan Uysal

The effect of intensive milling on the conversion of microcline ( KAlSi3O8) to potassium chloride (KCl) occurred during the chlorination roasting process for artificial KCl production was investigated. A feldspar ore with 10.89% K2O grade and containing microcline was dry milled by a planetary ball mill for mechanical activation. Milled ore mixed with calcium chloride was roasted at temperatures between 500 and 1000 °C to get the chlorination roasting process. The product was then leached in water to dissolve KCl occurring during the roasting, which will be precipitated from the pregnant leach solution by evaporation. Results showed that potassium recovery from the unmilled ore increased rapidly up to 800 °C, and dramatically decreased at higher temperatures due to the removal of KCl from the furnace by means of evaporation. A potassium recovery of 31.95% was achieved by the unmilled ore, whereas it was 88.43% when 15 min milled ore was roasted at 750 °C. It was concluded that intensive milling caused mechanical activation of microcline to reduce the roasting temperature of the chlorination roasting process.

May 31, 2023

By Fengmei Chen, Na Liu, Bingrui Li

A quantitative analysis method based on the airflow influence factors is proposed to evaluate airflow stability and discriminate airflow directions in complex ventilation networks. The law governing the changes in airflow caused by changes in branch resistance is revealed based on simulations of the airflow state in a ventilation network and a statistical analysis of the results. Then, three evaluation indices (airflow sensitivity, airflow influence factor, and critical airflow) are determined, matrices of the airflow influence factors and critical airflows are constructed, and a quantitative evaluation method for ventilation system stability and an airflow directional discriminant are proposed. The results show that the stability of a ventilation system can be reliably evaluated based on the airflow influence factors. The sensitive branches and dominant branches in the ventilation network can be determined based on the matrix of airflow influence factors, and the reversed branches, the trigger branches, and the reversal conditions can be determined based on the critical airflow matrix and the matrix of airflow influence factors. The proposed airflow directional discriminant is suitable for evaluating arbitrarily complex networks.

Nov 15, 2023

By Frank E. Chase

Preventing pillar squeezes, massive pillar collapses, and bumps is critical to the safe and efficient recovery of coal during room-and-pillar retreat mining. To help prevent these problems, the U.S. Bureau of Mines (USBM) has developed the Analysis of Retreat Mining Pillar Stability (ARMPS) computer program. ARMPS calculates stability factors (SF) based on estimates of the loads applied to and the load-bearing capacities of, pillars during retreat mining operations. The program can model the significant features of most retreat mining layouts, including angled crosscuts, varied spacings between entries, barrier pillars between the active section and old (side) gobs, and slab cuts in the barriers on retreat. It also features a pillar strength formula that considers the greater strength of rectangular pillars. The program may be used to evaluate bleeder designs as well as active workings. A data base of 110 pillar retreat mining case histories has been collected across the United States to verify the program. It was found that satisfactory conditions were very rare when the ARMPS SF was less than 0.75. Conversely, very few unsatisfactory designs were found where the ARMPS SF was greater than 1. 5.

Jan 1, 1995

By L. Adler

A systematic, balanced and inclusive formulation of the vast input data for mine design is presented. Since the quality of this statement severely influences subsquent design it is extremely important to senior mining engineers and the profession-at-large. If unfocussed, chaos can result along with serious ommisions. The basic categories, each a traditional one are: 1) Natural Conditions (geology and geography), 2) Company Capabilities (monetary and managerial), 3) Public Domain (regulations, contracts, good will, etc.) and 4) State of Art (mining engineering professionalism). To further reduce the data additional organizing principles were used: the distinctions of mining (vs. civil) engineering, proceeding from the general to particular, the basic engineering dimensions, and separating dependent from independent variables. The results are a unique and unified corpus, which anticipates the mine design procedure.

Jan 1, 1987

By W. J. Wuest

The U.S. Bureau of Mines (USBM) has recently developed a rock mass classification system for evaluating the structural competency of bedded roof strata; the Coal Mine Roof Rating, or CMRR. When compiled with the companion Lotus 1-2-3 spreadsheet, which is simple to learn and use, CMRR data are a useful tool with applications to longwall gate road pillar design, safety hazard mapping, and artificial roof support analysis. This paper demonstrates these applications under actual conditions found in current U.S. mining operations.

Jan 1, 1995

By Michael H. Inglis

The Technology Application Center, in conjunction with the U.S. Bureau of Mines Liaison Program, is studying the use of Landsat data for the monitoring of coal surface mine reclamation activities. Landsat may provide sufficient information to reduce the number of on-site inspections now required. The focus of the project has been the Navajo Coal Mine located in north- western New Mexico and operated by Utah International, Inc. On October 15, 1977, a field team recorded spectral measurements at the mine during the time of Landsat's overpass and a corresponding aerial photographic flight. Training sets were selected from the ground and aircraft data representing vegetated, graded, ungraded and natural environments. A supervised classification of the data was performed by the Stanford University Remote Sensing Laboratory then correlated to aerial photos and mine maps. The results, to date, have been very encouraging.

Jan 1, 1979