Search Documents

By G. St. J. Perrott

A study of certain fundamental characteristics of liquid-oxygen explosives has been made. A discussion is given of the factors affecting the life of the cartridge and the relation between explosive strength and oxygen content. The explosive properties of L.O.X. cartridges packed with a variety of lampblacks, gas blacks, and other materials have been experimentally determined by means of the ballistic pendulum, Bichel gage, and measurement of the rate of detonation. DURING the past year, the Bureau of Mines has carried on an investigation of liquid-oxygen explosives (L.O.X.) to supplement the work described in previous publications.' The present paper gives results of the first part of this work, which was a laboratory investigation of the properties of typical combustibles used in L.O.X., and the relation of these properties to the absorption and retention of oxygen by the explosives and their explosive characteristics. No attempt will be made to describe the development of liquid-oxygen explosives, because this phase of the subject has been well covered. The L.O.X. cartridge consists of a paper wrapper filled with an absorbent combustible material that is saturated with liquid oxygen by soaking it therein. After saturation, the cartridge is removed from the liquid and fired with fuse and cap, or electric detonator, in a manner

Jan 12, 1924

[Admissions: B. M. Gottlieb, Chairman Edmond F. Egan K. Marshall Fagin John S. Fuller Edward E. Monteith T. A. Pollard Howard J. Ritts, Jr. Kenneth W. Robbins Harold E. Wright Advertising and Exhibits: Bernard F. Klein, Chairman Bob Diggs Brown R. E. Howard H. M. Krause, Jr. R. G. Parker Mrs. Evelyn R. Robertson]

Jan 1, 1961

By R. P. Agarwala, M. S. Anand

Using residual activity technique, the diffusion of palladium, silver, cadmium, indium, and tin in alunzinum has been studied in the temperature range of 400" to 630°C. The diffusivities (in units of square centimeters per second) have been expressed as: IMPURITY diffusion in aluminum,1-9 silverand lead5 for cases of low solid solubility of the impurity in the host metal has yielded frequency factors in the range of l0-6 to l0-9 sq cm per sec whereas the activation energy is practically half the self-diffusion activation energy value. From the observed values of frequency factor, activation energy, and entropy of activation, it has been suggested' that these solutes are not diffusing by vacancy or interstitial mechanisms but by a mechanism which should be consistent with such low values of the diffusion parameters (Do and Q). However in spite of extensive work on these types of systems, the mechanism of diffusion is still not well understood. The present investigation on the diffusion of palladium, silver, cadmium, indium, and tin in aluminum has been carried out to throw further light on the diffusion mechanism in systems, where the solid solubility is very low (except for the case of silver). The results are discussed on the basis of solid solubility and the structural changes involved owing to the presence of the solutes in aluminum solid solution. An attempt has also been made to apply the existing theories of charge5-8 and size8 difference between the solute and the solvent. EXPERIMENTAL PROCEDURE Specimens (1/2 in. diam by 3/8 in. high) were machined out of pure aluminum (99.995 wt pct) rod obtained from Johnson Mattheys. They were sealed under vacuum in quartz tubes and annealed at 620° C for several hours; the grains thus developed were sufficiently large to eliminate the possibility of diffusion along the grain boundaries. The flat ends were prepared carefully after polishing as described previously,10 Radioactive nitrates of cadmium, indium, and tin and chloride of palladium containing, respectively, cd115, 1n114, sn113, and pd103 were dissolved in distilled water and mixed with 30 pct acetone. By means of a micropipet a drop of this solution was placed on a smoothly polished and lightly etched surface of the specimen. Due care was taken to see that the solution spread uniformly on the surface of specimen without trickling down its sides. Radioactive silver was elec-trodeposited using a AgCN-KCN bath. The amount of sample deposited in all the cases was not more than 0.1 µ thick. The samples were then sealed in quartz tubes in vacuum. The cadmium samples were sealed in a purified argon atmosphere to avoid evaporation. The samples were then diffusion-annealed. The temperature of annealing varied between 400° and 630°C and was controlled to ±5°C. On heating to -400°C,the deposits of cadmium, indium, and tin, which were of the order of 0.1 p in thickness, were converted to their respective oxides. The contribution of oxygen present in the lattice of aluminum due to these oxides has been calculated and found to be less than 10 ppm in all cases. Oxide method has already been used by other workers11'12 in diffusion studies without any controversy on the issue. However, in some of these investigations, metallic deposition was also tried. The diffusivities calculated from these measurements were found to agree very well with the diffusivities obtained by using the oxide method. Thus it is assumed that the measured diffusivities represent true diffusion coefficients. Since palladous chloride decomposes at about 500°C, the deposited samples which were to be diffusion-annealed below 500°C were heated in vacuum for a very short time at 500°C to allow the decomposition of palladous chloride to palladium metal. Time taken in decomposition of nitrates to oxides and chloride to metal was negligibly small as compared to the period of the diffusion anneals. The residual activity technique13 was used to study the diffusion profiles where thin layers from the specimen surface were removed by grinding it parallel to a flat surface on a 600-grade carborundum paper. The specimen was washed, dried, and weighed, the differ -ence of the weight being the measure of the thickness of the layer removed. After each such abrasion and weighing, the total residual activity on the surface of the specimens was measured by counting 0.656, 0.94,

Jan 1, 1968

By T. R. A. Davey

IN 1947 the author became interested in the fundamental aspects of the desilverizing of lead by zinc, conducted some experimental work, and searched the technical literature for all available fundamental data. Since then a revival of interest in the subject in Europe resulted in the appearance of quite a number of papers. It became evident that it would be more profitable to collect together and examine thoroughly the results of various workers, than to attempt to duplicate the experimental determinations. There are many inconsistencies in the various publications, and it is opportune to review at this time the present status of knowledge on the Ag-Pb-Zn system. There is also a need for a clear description, in fundamental terms, of the various desilverizing procedures. This paper is presented in four sections: 1—There is an historical review of the origins of the Parkes process, of the results of many attempts to find a satisfactory fundamental explanation for the phenomena, and of the modifications proposed to date. 2—A diagram of the Ag-Pb-Zn system is presented. This is believed to be free of obvious inconsistencies or theoretical impossibilities, although thermodynamic analysis subsequently may reveal errors. 3—The fundamental bases of the various desilverizing procedures, which have been used up to the present day, are described; and a new method is suggested for desilverizing a continuous flow of softened bullion in which the bullion is stirred at a low temperature in two stages producing desilverized lead at least as low in silver as that from the Williams continuous process and a crust which, on liquation, yields a very high-silver Ag-Zn alloy. 4—A suggestion is made for the revival of de-golding practice, following a recently published account which does not seem to have attracted the attention it deserves. The terms "eutectic trough" and "peritectic fold" as used in this paper are synonymous with "line of binary eutectic crystallization" and "line of binary peritectic crystallization" as used by Masing.' The German literature on ternary and higher systems is rather extensive and a fairly general system of nomenclature has arisen, whereas in English usage the corresponding terms are not as well established. For this reason the meanings of terms used in this paper, together with the equivalent German terms, are given as follows: 1—Eutectic trough—eutektische rinne: line at which a liquid precipitates two solids S1 and S2 simultaneously. If the composition of a liquid which is cooling reaches this line, it then follows the course of this line until a eutectic point is reached, or until all the liquid is exhausted. The tangent to the eutec-tic trough cuts the line joining S1S2. 2—Peritectic fold—peritektische rinne: line at which a solid S1 and a liquid L transform into another solid S2. If the composition of a liquid which is precipitating S1 reaches the line, on further cooling only S2 is precipitated. The liquid composition moves from one phase region (L + S1) into the other (L + S2), and does not follow the course of the boundary. The tangent to the peritectic fold cuts the line S1S2 produced nearer S,. 3—Liquid miscibility gap, or conjugate solution region—mischungslucke: the region within which two liquid phases coexist in equilibrium over a certain range of temperature. A system whose composition is represented by a point in this region comprises one liquid at high temperature; then as the temperature is progressively reduced, two liquids, one liquid and one solid, one liquid and two solids, and finally three solids. 4—Liquid miscibility gap boundary—begrenzung der flussigen mischungsliicke: the line along which the surface of the miscibility gap dome, considered as a solid model, intersects the surrounding liquidus surfaces. 5—Tie lines—konoden: lines joining points representing the compositions of two liquids, a liquid and a solid, or two solids, in equilibrium. In binary systems the only tie lines customarily drawn are those through invariant points, e.g., through the eutectics of the Pb-Zn and Ag-Pb systems, or the various peritectics of the Ag-Zn system, as in Figs. 1 to 3. In ternary systems it is desirable to draw sufficient tie lines to indicate the slopes of all possible tie lines. 6—Ternary eutectic point—ternares eutektikum: point at which liquid transforms isothermally to three solids, S1, S2, and S Such a point can lie only within the triangle 7—Invariant peritectic (transformation) point— nonvariante peritektische umsetzungspunkt: (a) — On the miscibility gap boundary, the point at which two liquids and two solids react isothermally so that L, + S, + L, + S2. (b)—On the eutectic trough, the point at which a liquid and three solids react iso-thermally so that L + S, + S2 + S3. Such a point must lie on that side of the line joining S,S which is further from S,. (c)—A further possibility, not found in this ternary system, is that the point is at the intersection of two peritectic folds when the reaction concerned is L + S, + S, + S Historical Introduction Karsten discovered in 1842 that silver and gold may be separated from lead by the addition of zinc.2 Ten years later Parkes used this fact to develop the well known desilverizing process which bears his

Jan 1, 1955

By Magnus Troilius

The method of using the bromine process of determining sulphur in steel, described below, is in successful use at the Midvale Steel Works. Ten grams of drillings are weighed out and put into the 1/2-liter flask A, with long neck. The flask is connected with a wide glass tube C', which, in its turn, is connected with the absorption bulbs B, containing HCI, 1.12 specific gravity, and ahout 5 C.C. of bromine. The wide tnbe C causes the vapor to condense and flow back into the flask A during boiling. The bulbs B connect with a long glass tnbe, which may be made to carry off the bromine fumes through a hole in a window, or, better still, through a flue with powerful draught. The connections being made, 100 C.C. of boiling water are run in through the thistle tube T. The air is thus completely driven out of the flask. 100 C.C. of HC1 (about 1.19 specific gravity) are then run in. When the gas begins to run rattler slowly through B, heat is applied until boiling gradually ensues. The steel being completely dissolved, the apparatus is disconnected, and the contents of B rinsed out into a beaker of 100 C.C. capacity, into which a few C.C. of a concentrated solution of BaCI, have been previously introduced. Heat is then applied (best by means of the hot iron plate) until the bromine is completely driven off and the BaSO, has settled nicely to the bottom. The BaSO4, is then filtered off on a small

Jan 1, 1884

By G. Derge, R. E. Grace

Diffusivity of bismuth in liquid Pb-Bi alloys has been measured by the capillary reservoir method as a function of temperature and composition. Fair agreement between theory and experiment is found for the measured diffusion coefficients and activation energies of diffusivity and viscosity in dilute lead alloys. The measured diffusion coefficients in the high bismuth alloys describe mass transport in special concentration gradients. THE study of diffusion in liquid metals has been restricted largely to the amalgams over small ranges of temperature and composition. In contrast to this, diffusion and transport of ions and molecules in aqueous and organic solvents have been studied extensively for the past 50 years. The general difficulty of measuring diffusion coefficients in both gases and liquids at high temperatures has been that of eliminating convection currents. Measuring techniques based on freezing and sectioning after the diffusion period1 are not particularly satisfactory because of the volume changes and segregation which occur during freezing. The most promising technique which is currently being developed for liquid metals is the capillary reservoir method. This eliminates convection currents from the diffusion zone and requires measurements only of the length and initial and final compositions of the alloy within the capillary. Anderson and Saddington' have measured the diffusion coefficient of tungstate anions in aqueous Na,W04; Wane4' and Hoffman- ave studied structure and self-diffusion in water and self-diffusion in mercury, respectively, by similar techniques. Selection of the Pb-Bi system for initial study was made for several reasons: I—It afforded a low temperature system for development of techniques which would be suitable for high temperature measurements in liquid iron. This research on diffusion in liquid iron is now in progress as a part of a general program on the rates and mechanisms of slag-metal reactions. 2—Activity data on liquid Pb-Bi alloys of all compositions are available from the emf meas- urements of Strickler and Seltz.9 3—Some data are available on the diffusion of bismuth into solid lead. The measurements on solid alloys were made by von Hevesy and Seith7 for the concentration range of 0 to 2 pct Bi. An appropriate solution to Fick's law (unsteady state) for the capillary reservoir has been found by considering the mass flow which passes through a unit area of surface on a slab of infinite thickness as a function of time. This is the first application of this solution to diffusion measurements, although a similar solution is available for identical boundary conditions.' By analogy with heat conduction, the problem reduces to a perfectly insulated infinite slab at temperature C,, one surface of which is quenched to C, for all times, t. Heat is permitted to flow from quenched surface of the slab to an infinite supply of coolant at C.' (see Appendix). For the corresponding solution for diffusion in liquids, these terms become Where Cu is the initial concentration of component A" in entire capillary at t - 0, C, is the final con- In this case. component A is bismuth, and C, = 0. centration of component A in entire capillary at t = t, C, is the concentration of component A in bath for all t, 1 is the length of the capillary in centimeters, t is the time of diffusion period in seconds, and D is the diffusion coefficient in square centimeters per second. By comparison with solutions to Fick's law used in the solid state, this solution for liquids is similar to the Grube solution for solids, where the change in D with chemical composition is not taken into consideration. Difficulty is to be expected if large concentration gradients are employed and if the concentration gradients extend over an appreciable length of the capillary.

Jan 1, 1956

By E. H. Jr. Dix

DURING an investigation of high-strength manganese bronze by the Engineering Division of the Air Service, at McCook Field, Dayton, Ohio, particles of a "blue constituent" were noted in the microstructure of most of the bronzes examined. The constitution of the simple copper-zinc base alloy is still a matter of dispute in spite of the fact that the copper-zinc series is one of the oldest industrially important groups of alloys, and has received the early consideration of scientific research. The diagram, according to the most recent work,1 is shown in Fig. 1. The disputed questions involve the termination of the beta field and the line at 470° C. The earliest experimenter, Roberts-Austin, detected an arrest in some of his cooling curves at approximately this temperature and ascribed them to the formation of a eutectic; it has since been proved that there are no eutectics in this series. Shepherd2 was unable to detect any thermal arrests at this temperature; his diagram was essentially as shown in Fig. 1, except that the line at 470° C. was omitted and the beta phase carried down to normal temperatures. Later, Carpenter and Edwards,3 by a very painstaking research, definitely established the authenticity of the line but attributed it to the breakdown of the beta constituent into a eutectoid of alpha and gamma. Microscopic evidence of the formation of the eutectoid is doubtful and it seems more likely to be due to an allotropic change in the beta constituent as shown by Fig. 1. At least for practical purposes, it is more convenient to think of the structure of a 60-40 brass as a mixture of alpha and beta prime crystals rather than alpha plus an unresolvable eutectoid of "apparent beta" as it has often been called.

Jan 5, 1922

By M. C. Udy, P. C. Rosenthal

The use of minute boron additions to steel has been given considerable attention in recent years. Comparisons made between boron-free and boron-containing heats of otherwise identical analysis have indicated, beyond a doubt, the potent effect of boron for increasing hardenability. The actual hardenability increase has been expressed as a multiplying factor, or in terms of the percentage of other alloying elements boron might replace. The present study presents the results of a systematic survey of the use of boron as an addition to two types of alloyed steels and as a replacement for various percentages of molybdenum in these steels. Both cast and wrought steels of the two basic compositions were prepared. Molybdenum, because of its scarcity at the time the investigation was started, was selected as the element to be replaced by boron. Attention was also given to the effects of boron on other properties of the steels, particularly their notched-bar toughness, to investigate other advantages or limitations of this element as an alloy addition. Experimental Work Steels Investigated The two basic compositions used in this survey of boron as a replacement for molybdenum are given in Table I. The cast steels were higher than the wrought steels in silicon content to improve the casting quality. Table i.—Nominal Composition of the Two Base Alloy Steels composition. Per Cent. steel Mn Si Ni Cr Xi-Cr-Mo Wrought 0.28-0.70-0.15-o.45—o.45-0.32 0.90 0.25 0.55 0.55 Cast 0.28-0.70-0.35-0.45-o.45- 0.32 0.90 0.45 0.55 0.55 hln-&lo Wrought 0.28-I .go-o.0.15-0.32 1.70 0.15 Cast o. 28- I.40- 0.35- 0.31 1.70 0.45 a Sulphur was 0.040 per cent maximum and phosphorus 0.030 per cent maximum. Each of these base steels, both cast and wrought, was made with molybdenum contents of o, 0.10, 0.20, 0.30, or 0.40 per cent, the total comprising 20 steels. In addition, each of these 20 compositions was prepared with boron additions in amounts of o.oo15, 0.003, and 0.006 per cent as ferroboron; and in amounts of 0.002 and 0.005 per cent as two commercial intensifier alloys, designated alloys A and B. The boron-treated steels totaled 100, and the entire series 120. Test Procedure Each steel was melted as an individual heat in a 50-lb., magnesia-lined induction furnace. Ingot iron scrap or mixtures of ingot iron and steel. scrap were used for melting stock. Deoxidation was carried out in the furnace with 0.10 per cent aluminum. The aluminum addition was

Jan 1, 1948

By M. C. Udy, P. C. Rosenthal

The use of minute boron additions to steel has been given considerable attention in recent years. Comparisons made between boron-free and boron-containing heats of otherwise identical analysis have indicated, beyond a doubt, the potent effect of boron for increasing hardenability. The actual hardenability increase has been expressed as a multiplying factor, or in terms of the percentage of other alloying elements boron might replace. The present study presents the results of a systematic survey of the use of boron as an addition to two types of alloyed steels and as a replacement for various percentages of molybdenum in these steels. Both cast and wrought steels of the two basic compositions were prepared. Molybdenum, because of its scarcity at the time the investigation was started, was selected as the element to be replaced by boron. Attention was also given to the effects of boron on other properties of the steels, particularly their notched-bar toughness, to investigate other advantages or limitations of this element as an alloy addition. Experimental Work Steels Investigated The two basic compositions used in this survey of boron as a replacement for molybdenum are given in Table I. The cast steels were higher than the wrought steels in silicon content to improve the casting quality. Table i.—Nominal Composition of the Two Base Alloy Steels composition. Per Cent. steel Mn Si Ni Cr Xi-Cr-Mo Wrought 0.28-0.70-0.15-o.45—o.45-0.32 0.90 0.25 0.55 0.55 Cast 0.28-0.70-0.35-0.45-o.45- 0.32 0.90 0.45 0.55 0.55 hln-&lo Wrought 0.28-I .go-o.0.15-0.32 1.70 0.15 Cast o. 28- I.40- 0.35- 0.31 1.70 0.45 a Sulphur was 0.040 per cent maximum and phosphorus 0.030 per cent maximum. Each of these base steels, both cast and wrought, was made with molybdenum contents of o, 0.10, 0.20, 0.30, or 0.40 per cent, the total comprising 20 steels. In addition, each of these 20 compositions was prepared with boron additions in amounts of o.oo15, 0.003, and 0.006 per cent as ferroboron; and in amounts of 0.002 and 0.005 per cent as two commercial intensifier alloys, designated alloys A and B. The boron-treated steels totaled 100, and the entire series 120. Test Procedure Each steel was melted as an individual heat in a 50-lb., magnesia-lined induction furnace. Ingot iron scrap or mixtures of ingot iron and steel. scrap were used for melting stock. Deoxidation was carried out in the furnace with 0.10 per cent aluminum. The aluminum addition was

Jan 1, 1948

By William Fink

ALUMINUM forms not only binary compounds with most of the metallic elements but also forms many ternary or more complex constituents. Several of those occurring in the more important alloy systems have been identified under the microscope and the action of various etching reagents has, been carefully studied.' The determination of the structure and composition of these complex constituents is a matter of some difficulty and little information is available. X-ray crystal analysis offers a promising method for the study of such constituents. First, and of considerable importance, is the possibility of recognizing the presence of a given constituent by means more positive than microscopic observation. Evidence can also be obtained concerning the nature and composition of the constituent in question and ultimately it should be possible, at least in some cases, to describe the structure including the relative locations of the various atoms. In this paper some results of an uncompleted study of the constituents of the aluminum-iron-silicon system are given and the methods employed are described. Inasmuch as iron and silicon are the chief impurities in aluminum, the constitutional relations of this system are of fundamental importance in the metallurgy of pure aluminum and its alloys; the system has been studied by several investigators and the more important contributions have been reviewed recently.2 Fig. 1 shows the structure of the aluminum-rich alloys after prolonged annealing at 560° C., in accord with one of the most recent investigations.3 The ternary alloys examined in the course of the present investigation were all annealed at 550° or 560° C.; in fact, some of the specimens were the identical ones used by Dix and Heath, who kindly supplied them for this work. Since the results

Jan 1, 1930

By J. L. Rodda, M. L. Fuller

In connection with an investigation in this laboratory on the high-zinc side of the copper-zinc system, it was observed that well developed segregate structures of the Widmansttten type were formed when a secondary phase precipitated from the solid solution of copper in zinc. This paper presents an analysis of the crystallographic relationship between the segregate and the solid solution matrix. The data to be presented are an interesting addition to the literature on segregate structures in that the plane of segregation is one of the less densely populated planes. In agreement with the generalization of C. H. Mathewson and D. W. Smith' the plane of segregation in the matrix contains the direction of closest atomic packing of the lattice. Furthermore, the matrix and the segregate are both hexagonal close-packed, which has not been reported hitherto in the 1iternture.l The increasing commercial importance of zinc alloys containing copper makes this fundamental study of value to the metallography of zinc alloys. Zinoeich Copper-zinc Alloys Copper enters into solid solution with zinc to at least 1.8 per cent at 400" C., according to W. M. Peirce.3 The solubility is less at lower temperatures. Thus a solid solution of copper in zinc, saturated at an elevated temperature, will precipitate the excess copper in a separate phase at a lower temperature, conditions of concentration, time, and temperature being suitable. The nature of these two phases has been established by the X-ray method of crystal analysis. Westgren and Phmgmén4 and also Owen and Preston5 have shown that the solid solution eta (7) is of the substitu-tional type with copper atoms replacing zinc atoms on the hexagonal

Jan 1, 1933

By Robert Abbott

THE influence of various elements in retarding or accelerating the absorption of carbon during the process of carburization is fairly well known. In general those elements which forth carbides accelerate the absorption, while those which do not retard it. It has sometimes been wrongly stated that those elements which raise the temperature of the critical range increase the absorption, while those which lower this temperature decrease it. Silicon is a notable exception to this rule, for its influence is to raise the critical range but to lower the absorption of carbon. Some elements which do not form carbides have no apparent influence upon the absorption rate. Carbon itself retards the absorption rate. With a view to obtaining more exact data upon the subject the following experiments were undertaken : 208 steels of different chemical composition were selected to represent most of the types of modern constructional steels. Specimens 3 in. in diameter and in. in length were weighed to milligrams. They were then packed in the special carburizing box shown in Fig. 1, and kept in .the furnace for 10 hours at a temperature of 900° C. A duplicate experiment was conducted at 1,000° C. At equal' intervals of time the box was rotated in the furnace so that. two complete revolutions were made in the 10 hours. This precaution was taken to neutralize as much as possible any effect of unequal heating. At the end of the 10 hours the box was allowed to cool in the furnace with the doors open. The specimens were then weighed again and the increased weight (carbon) determined. In. the following table are given the analyses of the various steels, together with the. increased weight of .carbon expressed in milligrams.

Jan 10, 1913

By William L. Fink, Kent R. Van Horn

Aluminum forms not only binary compounds with most of the metallic elements but also forms many ternary or more complex constituents. Several of those occurring in the more important alloy systems have been identified under the microscope and the action of various etching reagents has been carefully studied.' The determination of the structure and composition of these complex constituents is a matter of some difficulty and little information is available. X-ray crystal analysis offers a promising method for the study of such constituents. First, and of considerable importance, is the possibility of recognizing the presence of a given constituent by means more positive than microscopic observation. Evidence can also be obtained concerning the nature and composition of the constituent in question and ultimately it should be possible, at least in some cases, to describe the structure including the relative locations of the various atoms. In this paper some results of an uncompleted study of the constituents of the aluminum-iron-silicon system are given and the methods employed are described. Inasmuch as iron and silicon are the chief impurities in aluminum, the constitutional relations of this system are of fundamental importance in the metallurgy of pure aluminum and its alloys; the system has been studied by several investigators and the more important contributions have been reviewed recently.² Fig. 1 shows the structure of the aluminum-rich alloys after prolonged annealing at 560" C., in accord with one of the most recent investigations.3 The ternary alloys examined in the course of the present investigation were all annealed at 550" or 560' C.; in fact, some of the specimens were the identical ones used by nix and Heath, who kindly supplied them for this work. Since the results

Jan 1, 1931

By Robert Hunt

The American Institute of Mining and Metallurgical Engineers was the first American technical organization to consider steel-rail specifications and sections. If I am not mistaken, the first contribution on those subjects to the Proceedings of the Institute was presented by Prof. Thomas Egleston, in 1874, and was entitled "Investigations on Iron and Steel Rails made in Europe in the Year 1873.1" The next contribution was Dr. C. B. Dudley's report of his investigation for the Pennsylvania Railroad of the wear of steel rails in their tracks, in 1878, which contribution led to a very memorable discussion that extended through several meetings.2 In 1880, Mr. C. P. Sandberg3 presented an article on rail specifications and inspection and rail sections. This was followed, in 1881, by A. L. Holley,4 in his exhaustive report on the then used American rail sections. The next contribution, I believe, was made by myself' at the Buffalo meeting, in 1888, on steel-rail specifications, which I followed,6 in 1889, by a paper on steel-rail sections. Since that time there have been numerous contributions to the Transactions of the Institute in relation to the manufacture of steel rails. The American Society of Civil Engineers officially took up the investigation of the relation of rail sections to the wear of car wheels in 1888. In the prosecution of this work, the Society appointed a special committee, whose labors extended through several years and resulted in an exhaustive report to the Society in 1893.7 Later, another committee was appointed to consider specifications for the manufacture of steel rails; the labors of this committee extended over a period of several years, a final report8 being made in 1910. It was my fortune to be the secretary of both of those committees.

Jan 9, 1919

By B. G. Ricketts, A. Kelly, P. A. Beck

The isothermal kinetics (at 200" to 400°C) of subgrain growth and of softening were studied in a 99.997 pct pure Al crystal rolled to 80 pct RA, under conditions where recrystallization did not take place. It was found that the kinetics of subgrain growth and of softening were similar, and that the correlation between subgrain growth and softening was in first approximation independent of the annealing temperature. It has been shown by Heidenreich' by means of electron transmission microscopy and by Hirsch and Kellar2 by means of an X-ray microbeam technique that the crystals of heavily cold-worked polycrystalline aluminum consist of subgrains of approximately 2µ diam, which are slightly disoriented with respect to each other. This substructure is found on cold working at room temperature, without annealing. A preliminary study has been previously published3 of the softening upon annealing at 350°C of a heavily cold-rolled aluminum single crystal. Softening and X-ray line sharpening for such a rolled aluminum crystal were later studied in more detail as a function of annealing time and temperature.4 Perryman5, 6 has studied the recovery of polycrystalline aluminum after cold rolling. By means of phase contrast microscopy he found that the subgrain size increases with the annealing temperature but does not alter very much with annealing time at a given temperature. In the present work further study was made of softening as a function of annealing time and temperature and subgrain sizes were determined by two different techniques in an attempt to find any correlation that may exist between softening and subgrain growth. Subgrain size measurements were made both by the X-ray microbeam technique and by transmission electron microscopy. EXPERIMENTAL PROCEDURE For the X-ray studies specimens were cut from

Jan 1, 1960

By Richard P. Rothwell

THOUGH coal has been mined in this country for more than a century, no systematic effort was ever successfully made to ascertain the total amount produced. The production of the Cumberland Basin, Md., and the shipments from the anthracite fields of Pennsylvania, have been placed upon record, thanks to the intelligence sand foresight of Mr. C. Slack in the former case, and to the late Mr. B. Bannan in the latter. For some of the years between 1822 and 1842, the production of the Richmond Basin was reported by Mr. R. C. Taylor, but since that date till the author undertook this work it was impossible to obtain any statement of the production of this field. A few of the newer fields, such as that of Mt. Diablo, Cal., have been fully reported, and a few of the newer States have also had this service performed by some intelligent private individuals.; but no statistics of coal production have ever been collected either by the State or General Government, if we except the returns for the years 1869-70 of the census report. During the year 1875, by great exertions, I succeeded in obtaining, and July 3d, 1875, gave in the Engineering and Mining Journal what, "though not an accurate statement of our coal production," was " by far the most full and reliable that had ever been published." Though that report showed the production of bituminous coal to be 23,630,094 gross tons, or about six million tons more than had ever before been reported, it was in reality two and a half million tons below the actual output. The more full returns I obtained for 1875 gave many figures for 1874

Jan 1, 1877

By C. F. Quest, T. S. Washburn

The steel industry has a definite need in its tonnage mills for a formula relating expected tensile strength to the analysis of the steel. The McWilliam-Barnes1 and other less comprehensive formulas are used for this purpose, but these formulas were designed for an analysis range that does not include the medium manganese and silicon-bearing steels. This type of steel is being produced to meet the demand for tensile strength slightly higher than that of ordinary structural steel but not high enough to justify expensive alloy steels. The purpose of this paper is to present a somewhat more comprehensive formula based on data accumulated over a number of years by the Inland Steel Co., and to discuss the method followed in obtaining a formula to fit the data. The resultant formula admittedly is still weak in some respects, but for the expanded analysis range appears to be an improvement over the other formulas. It is hoped that with the collection of more data and possible collaboration with other mills studying this problem it will be possible to work out a more nearly perfect formula. Several publications have been issued on this subject. In some, the equation type of relation was evolved while others made a combination of tables and an equation. The latter include work by Campbel12,3 and Webster.4,5 Campbell classified the steels as acid and basic and applied a different formula to each. For basic steels, he used the equation: Teosile etrength = 41500 + 770C + 1000P + yMn [1 y was a variable depending on the carbon and manganese content of the steel and was listed in tables. Webster investigated acid Bessemer steel and developed the equation: Tensile strength = 38000 + 800C + xTP+ yMn [2]

Jan 1, 1940

By C. F. Quest, T. S. Washburn

The steel industry has a definite need in its tonnage mills for a formula relating expected tensile strength to the analysis of the steel. The McWilliam-Barnes1 and other less comprehensive formulas are used for this purpose, but these formulas were designed for an analysis range that does not include the medium manganese and silicon-bearing steels. This type of steel is being produced to meet the demand for tensile strength slightly higher than that of ordinary structural steel but not high enough to justify expensive alloy steels. The purpose of this paper is to present a somewhat more comprehensive formula based on data accumulated over a number of years by the Inland Steel Co., and to discuss the method followed in obtaining a formula to fit the data. The resultant formula admittedly is still weak in some respects, but for the expanded analysis range appears to be an improvement over the other formulas. It is hoped that with the collection of more data and possible collaboration with other mills studying this problem it will be possible to work out a more nearly perfect formula. Several publications have been issued on this subject. In some, the equation type of relation was evolved while others made a combination of tables and an equation. The latter include work by Campbel12,3 and Webster.4,5 Campbell classified the steels as acid and basic and applied a different formula to each. For basic steels, he used the equation: Teosile etrength = 41500 + 770C + 1000P + yMn [1 y was a variable depending on the carbon and manganese content of the steel and was listed in tables. Webster investigated acid Bessemer steel and developed the equation: Tensile strength = 38000 + 800C + xTP+ yMn [2]

Jan 1, 1940

By C. F. Quest

THE steel industry has a definite need in its tonnage mills for a formula relating expected tensile strength to the analysis of the steel. The McWilliam-Barnes1 and other less comprehensive formulas are used for this purpose, but these formulas were designed for an analysis range that does not include the medium manganese and silicon-bearing steels. This type of steel is being produced to meet the demand for tensile strength slightly higher than that of ordinary structural steel but not high enough to justify expensive alloy steels. The purpose of this paper is to present a somewhat more compre-hensive formula based on data accumulated over a number of years by the Inland Steel Co., and to discuss the method followed in obtaining a formula to fit the data. The resultant formula admittedly is still weak in some respects, but for the expanded analysis range appears to be an improvement over the other formulas. It is hoped that with the collec-tion of more data and possible collaboration with other mills studying this problem it will be possible to work out a more nearly perfect formula. Several publications have been issued on this subject. In some, the equation type of relation was evolved while others made a combina-tion of tables and an equation. The latter include work by Campbell2,3 and Webster.4,5 Campbell classified the steels as acid and basic and applied a different formula to each. For basic steels, he used the equation: Tensile strength = 41500 + 770C + 1000P + yMn [1] y was a variable depending on the carbon and manganese content of the steel and was listed in tables, Webster investigated acid Bessemer steel and developed the equation Tensile strength = 38000 + 800C + xP + yMn [2]

Jan 1, 1940

By F. Keeler, C. M. Craighead

Aluminum alloys containing magnesium and silicon are susceptible to strengthening and hardening by suitable heat-treatments, and they constitute a class of alloys of considerable commercial importance. Generally, they contain these two elements in the proportions required for the formation of the intermetallic compound Mg2Si, or an excess of silicon; no commercial wrought alloys are made with an appreciable excess of magnesium. The reason for not having excess magnesium is obvious from the results given in this paper, since it is shown that excess magnesium results in a proportional decrease in the solubility of Mg2Si. This is the eighteenthl of a series of papers from the Aluminum Research Laboratories dealing with the equilibrium relations in aluminum-alloy systems; most of the previous publications concerned binary aluminum-alloy systems; this is the fourth of a group pertaining to ternary aluminum-alloy systems. The work on this system was completed in 1930, but the results were not published because of the pressure of other work. Hanson and Gaylor2, in 1921, presented the results of an extensive investigation of the aluminum-magnesium-silicon system. Their results indicated that an excess of magnesium over the amount required to form the compound MgzSi caused a noticeable decrease in the solid solubility of MgzSi in aluminum. A more recent investigation3 in these laboratories showed that the solid solubility of MgzSi in aluminum was 1.85 per cent at 595' C. and decreased to 0.30 per cent at 300' C. The results of the latter investigation were used as the basis for the present work. The Present Investigation In the present investigation, a study was made of the effect of various amounts of excess magnesium upon the solid solubility of MgzSi in

Jan 1, 1936