Search Documents

Tasker (1985) has detailed the accepted practices for constructing polygonal blocks of influerrce in the estimation of ore reserves. Further he suggests that users might fall into traps such as omission or overlap when determining the area of influence for each sample point.As an example of these types of errors Tasker (1985) describes under "Coverage ofthe Area" how 25 per cent of the exploration area will not be included in an equiangular triangular grid where hexagonal blocks of influence are used.The introductory suggestion of Tasker (1985) of "incorrect procedure" by Rudenno (1983) (and Armstrong (1983)) reiterated around the Figure 2a of Tasker (1985), is based on the brief description of the polygonal area of influence by Rudenno (1983). That description is not too different from that given by King, McMahon and Bujtor (1982).

Jan 1, 1985

By Fairhurst RM

High pressure abrasive water jets have been shown capable of cutting a wide range of materials including steel, stone, rock and concrete. Acceptable performance can be achieved using relatively low pressures and expendable abrasives. The cutting head can be made small and abrasive feed systems have been developed that allow reliable pumping of slurries over long distances to supply such cutting heads. These features make abrasive water jets ideally suited to automated control in remote areas.Another major advantage of abrasive entraining water jet cutting heads is that they may be operated safely in potentially explosive environments due to their cold cutting ability. Therefore there are many possible applications for such equipment in mining.This paper gives an introduction to the abrasive water jet process and includes results of trials carried out at BHRA on a range of hard materials. Work is also described which investigated the operational safety of abrasive water jets in explosive environ-ments. In a special environmental chamber, cuts were made on steel and sandstone with atmospheres of methane/air and hydrogen/air, without caypsing ignition.

Jan 1, 1985

By Bukovinsky SB

The smelting, refining and hydrometallurgical operations practised in the winning of non-ferrous metals are associated with severe aqueous and high temperature corrosion problems.With the increasing costs of maintenenace and the utilization of computerization to control the processes, the trend in recent years has been to spend more capital on improved and proprietory grades of engineering materials, which offer greater reliability and more cost effective plant performance.The problems which have plagued stainless steel users for many years are the alloys' poor performance in chloride or other halide media where pitting, crevice or chloride induced stress corrosion cracking may occur, have been essentially solved by the new proprietory grades. The controlled additions of minor alloying elements including rare earth metals have led to the development of stainless steels with high mechanical strengths, improved corrosion resistance, and high temperature corrosion resistance and structural stability.

Jan 1, 1985

By Berglin IK

Since 1962, ferro alloy production in Australia has been concentrated at Bell Bay, Tasmania with a major expansion occurring in 1976. This concentration was based originally on the perceived requirements of the expanding Australian steel industry, but recent stagnation within this industry has seen Temco become progressively more export oriented.In 1984, approval was given for a $47 million uprating of facilities which will allow for the introduction of the latest technology to ensure high quality, low cost production in a highly competitive export market.

Jan 1, 1985

By Armstrong RW, Middlin B

The development, design, construction and operation of the new Solvent Extraction/BCA process plant at Copper Refineries Pty. Ltd., Townsville is described.The process offers substantial savings in electrical power costs, improvements in plant hygiene, and a lowering of materials handling costs compared with conventional electrowinning technology.The solvent extraction process extracts arsenic from copper Tank House electrolyte using a tributyl phosphate (TBP) - kerosene solvent. The plant incorporates fourextraction stages, two scrub stages, and three stripping stages to produce an arsenic-bearing low-acid strip liquor. This strip liquor is mixed with copper sulphate, and neutralized with ammonia to form a copper (II) arsenic (V) crystalline product, bicupric arsenate (BCA). This product is then used in the manufacture of chromated copper arsenate timber preservatives (Royston 1982).

Jan 1, 1985

The application and development of monitoring and control techniques of coal mines in China is mainly described in the paper.The techniques of mine control and monitoring system have been developed as an important means of production dispatch, command and management with ever-increasing coal production and gradual raising of the level of mechanization and centralization of continuous mining. The continuous stage monitoring and control system in China coal mines has been developed from the initial single fixed plant monitoring, and the technique of computers has also been applied in the system for productive and environmental monitoring, featuring a new type of mine control and monitoring equipment of China.

Jan 1, 1985

By Paine GG

The in-situ retorting of shallow oil shale deposits is an attractive alternative to the material handling problems of conventional open pit mining techniques, which involve removing overburden, fragmenting and transporting the shale to a fixed retort, and finally disposing of the hot spent shale.For in-situ retorting to be successful, the oil shale has to be fractured and the fragmented rock expanded into a void, to allow controlled propagation of a flame front through the in-situ retort. The principles of cratering with explosives have been used to develop a process for the in-situ fracturing of a thin oil shale deposit overlain by a formation of porous rock. The overlying porous rock formation is first compressed by explosive charges to create voids in the porous rock. The oil shale is then fragmented and pushed in to the voids with separate explosive charges. This paper discusses methods of creating voids in porous rocks with minimal surface disturbance, and then methods of obtaining the most uniform fragmentation of the shale. The whole process can be completed, in practice, in one blast. The results of an experimental blast are presented, and possible modifications are then discussed.

Jan 1, 1985

For several years, the Geology Department of the University of Canterbury has hosted a series of postgraduate projects in the field of coal studies, supported principally by the Ministry of Energy and to a lesser extent by private companies. These projects have involved mainly West Coast Coalfields, and my own studies have focussed on inorganic geochemical aspects of West Coast coals. Because of the large number of potentially important analyte elements in coal, and the wide diversity of coals occurring in the West Coast region, this project has required a substantial amount of work to be spent on sample collection, sample preparation, development of analytical methods, and actual analysis. Considerable problems must be faced at the sampling stage: Can sufficient information be obtained from whole-seam composites, or should seams be sampled in plies. Ply analysis is preferable, but results of proximate analyses are usually available for composites only. Where multi-seam drillhole samples become available (eg Greymouth Coalfield, where some holes yielded more than six sampled seams), the ply option involves a dramatic increase in the number of samples. I have attempted to strike a workable compromise between geographical coverage of coalfields, and detailed sampling of individual seams at each locality. In many cases, sample material has been used jointly with Jane Newman who has carried out petrographic studies.

Jan 1, 1985

By Murphy MW, Klaric SD

The history, operation and design of the Secor continuous rod production process is described. The effective operation of the plant is influenced by accurate monitoring and control of molten metal properties, mould release application, coolant application and composition and correct setting of all operating parameters. The continuity of operations, which is an essential feature of this type of plant, is also greatly influenced by the service life of wear parts in the operation. This paper deals with three principal wear parts which come into direct contact with copper during operation, these are:

Jan 1, 1985

By Getliffe RK

It is becoming more and more difficult to operate mineral and metal processes profitably, as operating costs rise, quality demands in-crease, international competition becomes more fierce and Government charges remain at their current levels. Profitability today depends upon efficient operations, which can only be achieved through precise and dependable con-trol of each process unit comprising thetotal plant.Modern process control systems utilise distributed architecture with microprocessor-based controllers, data acquisition devices and VDU operator stations. Honeywell intro-duced this control technology in 1975 with the "Total Distributed Control" System. Now, building on the proven performance and re-liability inherent in TDC hiway modules, Honeywell has extended the TDC system to inte-grate both management information and control by providing distributed processing modules on the new TDC 3000 Local Control Network (LCN).

Jan 1, 1985

By Moorrees C

Tests show how that temperature and rate of sparging to remove carbon dioxide determine the rate of precipitation and the chemical and physical properties of hydrated magnesium carbonates precipitated from clarified magnesium bicarbonate liquors derived from crude magnesia. At temperatures above 55°C the product is largely in the form ofhydromagnesite, Mg5(C03)4(OH)2.4H2O Between I5°C and 55°C the major product is nesquehonite, MgCO3·3H2O, although partial hydromagnesite precipitation can be induced by a high rate of aeration.As a result of the reduced time required to bring about greater than 95 per cent magnesium precipitation, the higher MgO content of the product, the ease of product recovery from the precipitation vessel, and the lower energy requirement for thermal decomposition of the precipitate to magnesia, it is preferable to precipitate hydromagnesite rather than nesquehonite. Moreover, the magnesia produced from hydromagnesite is somewhat more reactive than that formed from nesquehonite.Using precipitate calcination temperatures less than 1000°C, the chemical reactivities of the magnesias formed from both precipitates are greater than those of the crude magnesias derived from Savage River magnesite itself. The magnesias would be suitable for most uses developed for caustic-calcined magnesia. However, for refractory brick manufacture, it would be necessary to briquelle the caustic-calcined magnesia. adjust the CaO and SiO2 contents and sinter at temperatures in excess of 1600°C. This would bring about an increase in the bulk density and induce the appropriate chemical bonding reactions.Dead-burned magnesia produced from Savage River magnesite by the calcination/carbon dioxide route would have very low B2O3 contents, typically less than 0.0001 per cent.

Jan 1, 1985

Most of the gold reef mined today in South Africa is approximately 1 m in width with slopes about 30 m long. To prevent production interruptions it is essential that the stopes should not be blasted in sections. The shortage of experienced labour and arduous working conditions at the face dictate the need for simple blasting techniques.Hence, a pyrotechnic blasting system of sequential firing is in use at present, although research work to improve this technique is in progress.

Jan 1, 1985

About 60 persons are admitted to the graduate course every year after passing the entrance examinations. The entire course of studies is free of charge and the universities provide accommodation for the students who need it. The five years of studies are divided into 10 semesters. One semester lasts 15 weeks. Automatics can be studied at three separate faculties. At the University of Mining and Metallurgy, it is offered by the Faculty of Electrical Engineering, Automatics and Electronics as well as the Faculty of Mining and Metallurgical Machines (metrology can also be studied there); at the Silesian Technical University in Gliwice, the Faculty of Mining offers the course. The educational plans and programmes comprise 3 groups of subjects: common for a given course of studies (foreign languages, political science and the basic technical knowledge) common for the speciality and subjects of diploma courses. The whole time of studies covers about 4400 hours excluding 3 periods of professional training and the physical training. The classes, laboratory classes, seminars and design classes are obligatory and the attendance is strictly checked. Students may extend their knowledge by participating and working in the Science Clubs. The students' work is checked not only during the classes but also by the examinations held at'the end of respective semesters. Those who fail the exams can repeat them only if very important reasons are presented. At the very end of the studies there is a diploma examination together with a discussion on the diploma thesis, written by the student. The successful result entitles the student to recieve the title of "magister inzynier",M.Sc. of his speciality. The graduates, after working for 2 years, can attend another course of studies lasting 2 semesters and called "Postgraduate Course", or start "Doctoral Studies" finished by the defence of a doctor's thesis. In'these cases the expenses are usually covered by the graduates' employers.

Jan 1, 1985

By Bebb G

This paper describes the use of SURPAC, a survey/mine planning software package as used at Central Norseman Gold. It details the basic operating principles of the package, the applications in which it is employed, and its time and cost benefits and efficiencies as they apply to the above operations, both surface and underground.

Jan 1, 1985

By McMahon DW, Schapper MA

Hard rock underground mining has been wedded to the drill-blast method of breaking rock. Current practice and technology have focused on greater efficiencies in the blasting and handling of ore, on the basis that thelower costs that come with larger scale operations compensate for the waste dilution associated with the bulk methods. However, it is suggested that new technology is available or is on the horizon that could completely change the shape of hard rock mining in the 21st century. Hard-rock continuous-mining machines, possibly assisted by high pressure water jets, coupled with automated sorting and materials handling systems, could re-orient the miner's focus to winning metal rather than mining tonnes of ore. More continuous mining processes could accelerate the penetration by high technology in the hard rock underground mine, with the potential of greater manpower productivities and lower costs per tonne of metal produced. This new technology will be important in maintaining a competitive supply of metals, given the falling headgrades of the orebodies remaining for development and the increasing market threat from manufactured substitutes.

Jan 1, 1985

By Toro HCH, Von Borries GH

A brief description of the semi-autogenous grinding (SAG;) facilities of Compania Minera Disputada de Las Condes is given. A data-logging and computer system was connected to the plant inter facing the existing analog control system in a supervisory s, control philosophy. The development of a control straiov,v t,) maintain maximum power of the SAG mill atsubjected to process restrictions is shownThe present control scheme is discussed inalgorithm was designed based on correlations onLween vartaoles. Associated with this, a direct level of control was developed be, on classical control algorithms, process inter-active tuning has been included. Also, an algorithm to prevent overloading of the is discussed. Control scheme tests are presented in comparison t manual operator control under the same conditions. It is shown t the control strategy gives a more stable operation and a higher plant throughput.

Jan 1, 1985

By Campain RA, Horner NJ, Limerick JM

The review covers the different concepts of automation which are appropriate to non-ferrous smelting and the degree to which the smelter, and the furnace in particular, is amenable to total automation. Due to the problems peculiar to a smelter, it is unlikely that a fully closed loop system could ever be achieved and that the smelter will continue to depend upon extended manual control supported by computer based information sorting and optimisation.Generally, loop control is performed using Taylor's Mod III process control system. For distinct plant systems involving a combination of process loops, sequencing, and data acquisition, the company has developed its own microprocessor based systems. Process optimisation using computer based analysis of operating data is well established. Utilising this data, computer modelling provides manual set point supervision for the furnace process control system.The impact of automation on the workforce and on operating costs is also examined. Predictions on future developments in the field of automation, optimisation and sequencing are propounded and related to the non-ferrous industry at large.

Jan 1, 1985

By Hatherly P, Holt GE, McNally G

The current methodology for delineating and subsequently evaluating coal reserves is based on the use of vertical drill holes and surface based geophysics/geology. These techniques have three major problems, these being respectively:-a) Vertical drill holes can only provide a small sample of the coal seam and stratigraphy. Therefore the planar variation in coal reserve and environment parameters can only be approximated.b) Although surface based geophysics has had its fair share of success in recent years, there are still environments which have masked the finding of major structures.c) Access to drill sites is difficult at some locations due to mountaineous terrain, standing water and environmental impact.

Jan 1, 1985

Australia has been an important producer of zinc minerals and metal for many years.Late in the last century Edgar A. Ashcroft, a versatile and enterprising electrical engineer proposed the treatment of zinc rich ores by roasting, followed by leaching to extract zinc, purification of the solution and electrolysis of the purified solution to produce zinc. Residues from the leaching operation were to be smelted in a lead blast furnace to recover lead, silver and gold.Ashcroft (1897-98) and (1898) has.given us a most interesting record of the attempts made at the Sulphide Corporation's plant at Cockle Creek near Newcastle, NSW, to put his ideas into practice. In spite of the best efforts of all concerned, including the use of electrolysis of aqueous chlorides and sulphates, zinc could not be deposited consistently and the project failed although lead smelting continued until 1922 (Woodward, 1965, p. 158). Based on later experience with Broken Hill materials the presence of undetected cobalt in the solutions was the likely cause of the inability to deposit zinc (Kirk and Othmer, 1956).

Jan 1, 1985

By Krzystanek Z, Wasilewski S

The problem of automatic control of a coal mine ventilation network is discussed. It is found that the structure of the control sys-tem should have two levels, i.e. local regulation of ventilation para-meters (air flows) in faces to eliminate the effect of quick disturba-noes, and supervisory control of the whole ventilation process by pe-riodical modifications to the working characteristics of the main fans. Practical and theoretical problems connected with implementation of the system in Polish mining are listed and discussed. To solve these prob-lems a series of experiments with air flow control in three different coal faces were carried-out with the aim of checking the measuring and control equipment in a real mine conditions as well as investigatingthe gasodynamics of the ventilation process. The results of the experi-ments are analysdd, and used to verify the mathematical model of the gasodynamics of a longwall face.

Jan 1, 1985