Search Documents

Phelps Dodge Mining’s Bagdad, AZ copper facility uses a large series of cone crushers and ball mills to reduce copper ore to very fine particles. The solids are mixed with water to create a slurry. Milk of lime is added to this slurry to raise the pH. Small amounts of reagents are also added, including a frother to make bubbles, as well as a collector chemical that causes the copper minerals to stick to those bubbles. This material is pumped to a series of froth flotation cells to concentrate the copper. Air is blown into the flotation cell tank and the pulp mixture is vigorously agitated. Rising bubbles carry the copper particles over the edge of the flotation tank. The bubbles break after they flow over the edge.

Jan 1, 2005

By X. Y. Yu, X. A. Wei, A. Zeng

"The flotation behaviors of diaspore and three kinds of silicate minerals - kaolinite, illite and pyrophyllite - using an organosilicon cationic surfactant as collector were investigated as functions of reagent concentration and pulp pH. The results show that the organosilicon cationic collector QAS122 is a suitable collector for the flotation of aluminosilicate minerals but has weak collecting ability with regard to diaspore, enabling the flotation separation of diaspore from silicate minerals using QAS122 as collector. The flotation of a bauxite ore was then studied in detail. Finally, a reverse flotation separation process was used to process a low-grade bauxite ore. It was concluded that use of the organosilicon cationic collector is effective. A concentrate with aluminum oxide (Al2O3) to silicon dioxide (SiO2) mass ratio, or A/S, of 9.67 was obtained from natural bauxite ore with A/S of 6.07 at pH of around 11. The Al2O3 recovery rate was 81.72 percent. IntroductionChina has abundant bauxite ore resources, but more than 98 percent of the bauxite ores are the diasporic type, with the characteristics of complex mineral composition, low aluminum oxide (Al2O3) to silicon dioxide (SiO2) mass ratio, or A/S, and difficulty of processing. The gangue minerals in bauxite ores are mainly kaolinite, pyrophyllite and illite, containing titanium and iron impurities (Zong et al., 2008). It is known that high-grade bauxite ore, with A/S greater than 8, can be processed directly by the Bayer process (Papanastassiou et al., 2002; Ma et al., 1996). However, Chinese diasporic ores have been processed mainly by the sintering process, which is environmentally damaging and energy intensive. Increasing the A/S of the diasporic ores using a flotation method is needed (Xia et al., 2010).Froth flotation is one of the most widely used processes to concentrate valuable minerals in beneficiation ores. It is particularly useful for separating finely ground ores from their associated gangue minerals. For diasporic bauxite ores, flotation is applied to obtain high-quality material for the Bayer process by increasing the A/S. Direct flotation has been shown to be an efficient method for the desilicating of diasporic bauxite ore (Wang et al., 2004; Xu et al., 2004), but reverse flotation has more advantages for this purpose, including less collector consumption, less foaming product and less effect on metallurgy (Liu et al., 2007; Hu et al., 2003; Hu, 2003; Luo et al., 2001)."

Jan 1, 2015

By Ashma Singh, Nichole Maistry

Due to declining iron ore grades, low-grade ores with complex mineralogy — namely, banded iron formation (BIF) — are being explored to maximize iron ore resources and increase the life of mine. Flotation is the standard global process used for the beneficiation of BIF ores, as it is a complex ore reserve, and liberation is typically achieved below 1 mm. This study focuses on the flotation of a South African BIF, evaluating its response to different collectors, as well as effect of grind. As flotation is an expensive process and South Africa ranks high on the production cost curve, preconcentration by gravity or magnetic separation is performed prior to flotation. Thus, flotation was also performed on a gravity concentrate to determine if a grade suitable for steelmaking (approximately 63 percent) is achievable. The results indicate that the use of an alkyl ether amine-based collector partially neutralized with acetic acid is suitable for separation of hematite from illite and quartz at high pH values. Further optimization tests are being pursued to improve overall recovery and grade.

May 1, 2025

By P. Somasundaran, S. Venkatachalam, N. K. Khosla, K. Khosla

Froth flotation of alumina particles was studied by employing and hydrogen gas bubbles. The effect of current density was studied over a range of 0.1 to1.6 kA/m2. Compared to hydrogen, the use of oxygen bubbles at any given gas evolution rate resulted in a higher flotation recovery. The existence of an optimum current density, for each given particle size was indicated. Flotation at higher current densities resulted in better flotation kinetics, while flotation at lower current densities resulted in better Spas utilization.

Jan 1, 1996

By Brij M. Moudgil

Separation of dolomite from apatite, because of nonselective adsorption, cannot be achieved by conventional froth flotation technique. Results obtained in the present study also indicate, that this can be attributed to the depletion of the collector molecules due to complexation with the calcium and magnesium ions, dissolved from the two minerals. However, it has been established in this investigation that conditioning the material at pH 10, followed by reconditioning, without any additional collector, at pH 4, results in selective flotation of dolomite from the mixture. The recovery of apatite, in the proposed reconditioning process, is much higher than with the conventional conditioning under similar pH conditions. The mechanisms involved in the conventional conditioning, and the reconditioning process are presented.

Jan 1, 1983

By Heriban Soto

Primary amines are strong collectors of apatites and they can selectively float sedimentary phosphates from calcareous ores. However, secondary and tertiary amines and tri-methyl ammonium salts were ineffective. The use of kerosene reduces the collector requirements because hydrocarbon is coadsorbed along with the amine on the mineral surface. The heats of reaction of aminium ions with such anions as phosphate, carbonate and sulfate, were measured in a microcalorimeter and discussed in terms of the solubility of the precipitates formed and their relationship with the adsorption mechanism of primary amines on phosphate minerals. Experimental evidence supports a view that primary amines are adsorbed through chemical interaction between the aminium and phosphate ions at the mineral surface.

Jan 1, 1984

By Theodore Balberyszski

The gradual depletion of high-grade sulphide mineral deposits has turned the attention of the mineral industry to the recovery of metals from the oxides and silicates. Anionic (fatty acid) and cationic collectors have in some cases made flotation of non-sulphides possible, although in general, flotation of oxide ores is not as yet an economic process. Consequently, many attempts have been made to sulphidize the surface of the relevant oxide mineral and thus make it amenable to flotation. (1) (2) (3) In recent years, Bautista and Sollenberger(4) have investigated the conversion of a number of oxides to sulphides by reacting them with molten sulpur. This paper presents the results of investigations carried out at the School of Mineral and Metallurgical Engineering at the University of Minnesota to study the flotation characteristics of some sulphidized minerals. It is divided into two parts; Part I describes the sulphidization of a number of oxides and a silicate, and Part II presents the flotation behavior of the products of sulphidization.

Jan 1, 1968

By G. L. Simmons.

Many large. low-grade (refractory) sulfide gold resources exist in Nevada and other parts of the world that are not amenable to concentration by conventional flotation practice, Over the past several years Santa Fe Pacific Gold (SFPG) has investigated flotation process options to economically treat low-grade refractory resources of this type at Lone Tree and Twin Creeks. Conventional flotation technology applied to the original high-grade gold resources at Lone Tree and Twin Creeks was initially unsuccessful. Review and analysis of auriferous (gold-bearing) iron sulfide mineralogical characteristics and flotation chemistry provided a fundamental understanding that led to the development of a new flotation process that SFPG refers to as N2TEC. This paper discusses the development of this technology and compares N2 TEC results with conventional flotation practice.

Jan 1, 1997

By Gary L. Simmons

Many large (refractory) sulfide gold resources exist in Nevada and other parts of the world that are not amenable to conventional flotation concentration using air as the flotation gas medium. Over the past five years Santa Fe Pacific Gold Corporation (SFPG) has investigated flotation process options to economically treat refractory ores and resources of this type at its Lone Tree and Twin Creeks mines. Conventional flotation technology applied to the original high-grade gold resources at Lone Tree and Twin Creeks was initially unsuccessful. Review and analysis of auriferous (gold-bearing) iron sulfide mineralogical characteristics and flotation ..:hemistry provided a fundamental understanding that led to the development of a new flotation process that SFPG refers to as N2 TEC. This paper discusses the development of this technology and compares N TEC results with conventional flotation practice.

Jan 1, 1997

By M. S. Celik, G. Onal, S. Atak

The beneficiation of boron minerals flotation with well defined systems has been only slightly, investigated in the literature. The difficulty arises from fact that boron minerals cover a spectrum of solubilities. Colemanite (a calcium-containing, relatively insoluble, boron mineral) and borax (a highly soluble boron mine, have been used to exemplify the flotation of boron minerals. Using sodium dodecylsulfonate (SDS) and dodecylamine hydrochloride (DAH), the floatability responses of these boron minerals are considerably different. This has been ascribed to variations in the solubilities of boron minerals and the presence of cations in the lattice structure. In study, flotation tests and zeta potential measurements used to determine the flotation mechanisms of boron minerals.

Jan 1, 1994

By M. S. Celik

Beneficiation of boron minerals by flotation with well defined systems has been very little investigated in the literature. The difficulty arises from the fact that boron minerals cover a spectrum of solubilities. Colemanite, a calcium containing relatively insoluble boron mineral, and borax, a highly soluble boron mineral have been used to exemplify the flotation of boron minerals. The floatability of both minerals using sodium dodecylsulfonate and dodecylamine hydrochloride exhibits considerable differences in their response to flotation. This has been ascribed to variations in the solubilities 0f boron minerals and the presence of the cations in the lattice structure. Flotation tests along with zeta potential measurements are used to elucidate the mechanisms involved in the flotation of boron minerals.

Jan 1, 1992

By R. F. Yap

Although laboratory studies of tin flotation have been reported as far back as the 1920`s(1), the commercial application has only been realized within the past few years(2,3). The principal technical difficulty in the application of the process to tin ores has not been in the flotation of cassiterite itself, this mineral being readily recoverable with the common collectors, including xanthates with heavy metal ion activation(2). The difficulty has been with the depression of the gangue minerals commonly associated with tin ores, and to a lesser extent with the problems of collector consuming semi-colloidal minerals which are in some cases present. The application of sulfosuccinamate collectors to flotation of cassiterite from the Catavi, Bolivia, slime tailings has recently been described(3). The investigation which led to this successful process development included studies of other samples of gravity plant tailings as well as of lode tin ores. A common flowsheet with few significant variations was applied to most of these ore samples with acceptable results. In the following the process is described and the results of its application to samples from Bolivia and elsewhere given. Among the factors considered are: gangue depression, particle size and slime effects, and reagent and pulp density levels.

Jan 1, 1971

By J de Cuyper, G. Rinelli, A. M. Marabini, V. Alesse, W. Freyberger

Salicylaldehyde, a chelating agent for tin, has been found to function as a collector for the flotation of cassiterite. Infrared and nuclear magnetic resonance studies clearly show that salicylaldehyde can form a chelate compound in bulk and at the surface. Results are also given for the flotation of a tin ore with this reagent.

Jan 1, 1976

By R. A. Wharton, Z. Yang, R. W. Smith

The electrokinetic and flotation behavior of the green alga Chlorella vulgaris was studied in the absence and presence of Pb(II), Al(III) and flotation collectors. It was found that the presence of Al(III) is necessary for good flotation of the organism, whether or not Pb(II) is present, when dodecylammonium chloride or sodium dodecylsulfate is used as collector. Best flotation using dodecylamine is at about pH 8, and best flotation when using sodium dodecylsulfate is at about pH 4. It appears because of the small size of the organisms that the Al(III) is necessary for flocculation to enhance bubble-cell contact and C. vulgaris removal from water. When N-dodecyl-2-aminopropionic acid is used as collector, good flotation occurs at about pH 4 without the addition of Al(III).

Jan 1, 1992

By R. W. Smith

The electrokinetic and flotation behavior of the green alga Chlorella vulgaris was studied in the absence and presence of Pb(II), Al (III) and flotation collectors. It was found that the presence of Al (III) is necessary for good flotation of the organism whether or not Pb(II) is present when dodecylammonium chloride or sodium dodecylsulfate is used as collector. Best flotation using dodecylamine is at about pH 8 and best flotation when using sodium dodecylsulfate is at about pH 4. It appears because of the small size of the organisms that the Al (III) is necessary for flocculation to enhance bubble-cell contact and C. vulgaris removal from water. When N-dodecyl-2-aminoproprionic acid is used as collector good flotation occurs at about pH 4 without the addition of Al (III).

Jan 1, 1990

By H. Soto, G. Barbery

The effect of particle size on the flotation of coarse particles is analyzed. It is concluded that turbulence and the presence of the froth layer are detrimental to the recovery of coarse particles during conventional flotation. A counter-current column cell is proposed to avoid these two factors. In this column, a net upwards flow of water is prevalent, such that no froth is allowed to form on the top. Also, the levitation of heavy bubble-particle aggregates is helped by the ascending water current. Preliminary work at laboratory level with kilogram-size samples indicated that under similar conditions recoveries in the column were much higher than in conventional cells. Flotation results obtained with coarsely sized phosphate and quartz samples are presented. One interesting feature of this type of column is very fast flotation kinetics. Thus, a short column (only 55-cm collection zone) yielded, full recovery of floatable values.

Jan 1, 1992

By H. S. Soto

The exact reasons that explain the low recoveries of coarse particles in conventional flotation machines are not clear. Being a concern for only a couple of mineral industries comparatively very few studies have been devoted to the problem of coarse particle flotation. Coarse particles flotation is particularly important in potash and phosphate beneficiation. Potash concentrates with particles larger than 1-2 mm do not require additional compaction or recrystallization and receive a premium price. However, recovery of this size particle in conventional flotation cells is very low, and therefore, the coarse floation tailings have to be reground and refloated to produce, at a higher cost, a less desirable concentrate. In phosphate beneficiation deslimed coarse ore (nominally l4x35 or l6x35 mesh) is normally treated separatedly from the finer (35x150 mesh) ore. Concentration by conventional froth flotation alone yields very low recoveries, and therefore, additional processes such as agglomerate flotation in tables spirals and belt conveyors have to be used ( Moudgil and Barnett 1979). Fatty acids and fuel oil used in phosphate flotation have a moderate level of selectivity but considerable amounts of sand report to the froth product, thus concentrates have to be further upgraded by a double flotation process. Concentrates from the anionic circuit are scrubbed in an acidic media to desorb the collectors and then refloated in a cationic circuit to eliminate the fine silica (Lawver et.al. 1978). In this paper the reasons that explain the low recovery of coarse particles in conventional flotation are discussed. A flotation column modified according to the main conclusions of this discussion is tested with two coarse phosphate samples.

Jan 1, 1989

By Deepak Gupta, Brij M. Moudgil

Attempts were made to improve the recovery of coarse phosphate particles by adding selected frothers or precoated fine particles. A number of frothers for floating, specifically coarse coal and metallic minerals, were examined. Two of the frothers increased the flotation recovery of coarse phosphate by 3% on bench scale. Plant evaluation yielded improvements in overall phosphate recovery in the presence of these frothers. Addition of fine particles was also found to enhance coarse flotation under given conditions. Size, amount, and hydrophobicity of the fines added was determined to have a major influence on the coarse flotation efficiency. The grade of the product with and without frothers and particulate additives remained the same. Change in froth stability and viscosity are believed to be the primary reasons for enhanced recovery of coarse phosphate particles.

Jan 1, 1989

By W. C. Hirt

Deposits of ferromanganese crust containing cobalt and nickel occur on the seafloor in the Pacific Ocean near the Hawaiian Islands and Johnston Atoll. This paper describes developmental flotation metallurgy to separate crust from its associated substrate gangue. Important variables in ferromanganese crust flotation include reagent type, aeration rate, conditioning time and agitation intensity, pH, temperature, water type, and feed size distribution. Flotation in seawater of minus 600 ~m (-28 mesh) material assaying 6.2% Mn, 0.2% Co, and 0.13% Ni with diesel fuel-crude tall oil-sulfonate collectors produces concentrates assaying 15% Mn, 0.6% Co, and 0.3% Ni with recoveries of 89-95% while removing 62% of the feed weight.

Jan 1, 1990

By M. S. Celik, A. Aslanbas, B. Pehlivanoglu, R. Asmatulu

The principal impurities in some feldspar ores are titanium and iron, which impart color and degrade the quality of the ore. Mineralogical investigations indicate that, while titanium originates mainly from rutile with small amounts of sphene, iron originates mainly from mica minerals. Fatty acids, particularly oleic acid, are extensively used, with reasonable success, in the flotation of colored minerals from feldspar ores. In this study, potassium oleate, oleoyl sarcosine and hydroxamate were used to float colored impurities both before and after magnetic separation. Oleoyl sarcosine is found to exhibit better results compared to other reagents. Magnetic separation followed by flotation is found to produce a feldspar concentrate of superior grade.

Jan 1, 2002