Search Documents

By Henry A. Russell

During the last ten years Parsons Brinckerhoff has become a leader in the area of tunnel rehabilitation. A significant part of any tunnel rehabilitation program is the control of groundwater infiltration into the structure. This leakage over time, causes deterioration of the structures, and creates numerous operational problems for the tunnel operator. This paper will address current procedures for identification, documentation, and recommendations of repair methods for the control of groundwater infiltration in rail and highway tunnels.

Jan 1, 1993

By J. M. Mutmansky

Introduction Since the Hardy Cross numerical algorithm was applied to the solution of mine ventilation networks, numerous developments have taken place in ventilation network analysis procedures. The Newton-Raphson method, the linear theory method and the second-order approximation method are three of the additional approaches that have been applied. The efficiency of a ventilation network analysis procedure depends not only on the method of solving the system of equations derived from ventilation networks but also on the method of deriving the equations through selection of the meshes. This paper investigates the impacts of three mesh selection methods on the efficiencies of four ventilation network procedures. The minimum-resistance spanning tree method is the most popular procedure for selecting meshes. The shortest-path method was suggested by Epp and Fowler (1970) for improvement of the Newton-Raphson method. The minimum-resistance-path method is suggested here as the third method of selecting meshes. The effects of these three methods on the Hardy Cross method, the Newton-Raphson method, the linear theory method and the second-order approximation method are analyzed in this paper. These network analysis methods have been summarized in the paper by Kim and Mutmansky (1991). Mesh selection methods A procedure for mine ventilation network solution based on mesh equations typically consists of two steps: • the mesh selection step and • the network solution step. The mesh selection step establishes a set of independent equations to solve the network. The resulting equations are nonlinear. One method of solving nonlinear equations is to linearize the equations and iteratively solve these linear equations. The four analysis methods previously discussed in this paper use this approach. The linear equations required for solution can be written in matrix form as: P•dQ = dF (1) where P is the pseudo-resistance matrix, Q is the quantity matrix, and F is the Jacobian matrix (Kim and Mutmansky, 1991). The efficiency of the solution method depends on the characteristics of the P matrix, which in turn depend on the method of selecting meshes. To understand the impacts of the mesh selection methods on the efficiency of the ventilation network analysis procedures, the characteristics of the P matrix must be understood first. The diagonal elements of the P matrix, m in number, are the sums of the pseudo-resistances of the branches contained in the m meshes necessary for solution. The off-diagonal elements are the sums of the pseudo-resistances of the branches shared by two meshes. For example, P12 (first row, second column element of the P matrix) is the sum of the pseudo-resistances of the branches common to mesh 1 and mesh 2. When solving the system of equations expressed in Eq. (1), three of the iterative procedures (the Newton-Raphson, the linear theory and the second-order approximation methods) use the direct factorization method (Burden and Faires, 1985) on the P matrix. When the direct factorization method is used, the computational efficiency is enhanced by larger diagonal elements and a sparser P matrix. Generally, the sparsity of the P matrix is more important than the size of the diagonal elements. There is no known mathematical method of predicting the efficiency of these procedures, but heuristic methods can be used to study the efficiency. The Hardy Cross algorithm applies the Gauss-Seidel method of splitting the P matrix and applies the Newton-Raphson procedure. The efficiency of the Hardy Cross method depends on the spectral radius of the matrix[[D-L]-1U], where D is the diagonal, L is the lower triangle and U is the upper triangle of the P matrix for the Newton-Raphson method (Ortega, 1972). The smaller the value of the spectral radius, the faster the convergence. As with the other three methods, larger diagonal elements and a sparser matrix aid in faster convergence. With the Hardy Cross method, however, the size of the diagonal elements is more important than the sparsity of the matrix. Remembering that each of the diagonal elements of the P matrix is the sum of the pseudo-resistances of the branches in a mesh and that each off-diagonal element is the sum of the pseudo-resistances of the branches shared by two different meshes, the following strategies can be used: • Avoid having branches with larger resistance values shared by multiple meshes. This increases the size of the diagonal elements and reduces the chance of off-diagonal elements being large.

Jan 1, 1993

By J. E. Hoffman, Massimo Maccagni, T. J. Keefe, Marco Olper, O&apos

The problem relating to the use of insoluble anodes in acidic and highly aggressive environments has still not been definitely solved, and it is therefore a recurring subject of discussion. The fields of application in which insoluble anodes play a fundamental role are mainly in the electrolytic extraction of metals, in cathodic protection with impressed current, and in the production of oxidized halogenated salts. Based on the foregoing, B.U.S Engitec Servizi Ambientali (BESA) developed an electrode suitable for the use in the above-mentioned system. The basic component of the BESA anode is a bimetallic wire made of a copper rod (core) covered by a thin layer of valve metal, to be chosen between tantalum (Ta) and niobium (Nb). The wires, coated with suitable catalyst (PbO2, Pt or others) are inserted in a plastic frame and fixed to a current feeder by means of a screw, ensuring an optimal contact. Experimental data on the operating conditions, such as kind of electrolyte, current density, electrode potential, corrosion tests and fields of possible application, are described.

Jan 1, 1993

By Rolf J. Wesely

Recent events in The Peoples Republic of China indicate that a major effort is underway to increase trade with the western world. Gold production contributes to China's ability to participate in international trade. Consequently, the Chinese government places a high priority on increasing gold production. Many of the operating gold mines in China contain refractory ores that to date have not been efficiently treated. Figure 1 illustrates the description and location of a few of China's major gold mines. China recognizes that the technology necessary to economically treat this ore has been developed in the United States and other western countries. The country has therefore begun to seek assistance in evaluating several potential projects. Organizational structure Gold mining and processing in China is directed by the China National Gold Corp. (CNGC), headquartered in Beijing. The agency has a director in each province who is responsible for exploration, mining and processing. CNGC uses the services of two engineering organizations for metallurgical testing, process development and design engineering for their projects. The largest engineering organization is the Central Engineering and Research Institute for Non-Ferrous Metallurgical Industries (ENFI), also located in Beijing. The second engineering organization is the Changchun Gold Design Institute (CGDI), located in Changchun Jilin province.

Jan 1, 1993

By Y. Topkaya, R. E. Johnson, D. Buttinelli, B. R. Palmer, A. Geveci, L. Stoppa, C. Lupi, F. Pochetti

Representative samples of a composite mixture of three typical Cu/Zn complex sulphide ores, namely Black-, Yellow- and Altered-ore, from the Cayeli deposit in Turkey, were used for leaching tests in 2.2 M FeCl3, or 1 M CuC12-2 M NaCl solution in the temperature range from 313 K to 363 K (40O to 90O C), with and without the presence of an organic solvent for elemental sulphur, such as CCl4. The leaching rates of copper and zinc were quite high, as expected, in FeCl3 solution and complete recovery of both metals was obtained at the highest temperature when the solvent was present. However in CuC1, solution, extraction yields of the order of 95% only for Cu and Zn were achieved and the positive effect of the solvent was not clearly shown. The kinetics curves of Cu leaching by FeCl3 indicated a model of reaction rate depending on the particle surface, as in a chemically controlled reaction, in tests with the presence of CCl4. Without the solvent, or in CuCl2 media, the model of the diffusion controlled reaction seemed to prevail. Values of apparent activation energy, in both of the leaching processes, were determined and compared with those reported in literature.

Jan 1, 1993

By J. A. Brierley, C. L. Brierley, K. A. Prisbrey, R. W. Bartlett, J. G. Harrington

Bacterial oxidation of gold-encapsulating sulfide minerals in low-grade refractory ores was investigated over a period of one year. Crushed ore samples were held in wet, bacteria-inoculated, aerated columns. Sulfide mineral oxidation data were correlated with subsequent gold cyanide extractabilities. Experimental results for both sulfide conversion and gold extraction were compared with a biooxidation kinetics model that incorporates rock size, mineral grain size, and heterogeneous pyrite reaction kinetics. Using the model, extrapolations were made over three years for biooxidation of ore in large stockpiles. Ferric ion (oxidant) diffusion in the solution-filled pores of the rock matrix does not control the biooxidation kinetics of ore crushed to -25 mm.

Jan 1, 1993

By Malcolm J. McPherson

Within the world of mining health and safety, increasing attention is again being given to underground fires and explosions. This paper reviews the effects of open fires in mine entries on the ventilation system, and outlines current methodologies of attempting to control such a fire. The particular hazards of a fuel-rich fire are discussed. There appear to have been no really significant advances made in methods of extinguishing mine entry fires in the last several decades. The final section of the paper introduces research that is investigating the simultaneous production of an inerting, cooling and quenching atmosphere by means of a dense water fog.

Jan 1, 1993

By Debra C. Man, S. Thomas Freeman, F. Wiley Horne

INTRODUCTION The Metropolitan Water District of Southern California (Metropolitan) is the largest water wholesaler in southern California. Its service area spans the major urbanized portions of Ventura, Los Angeles, Orange, San Bernardino, Riverside and San Diego counties. More than 15 million people are serviced by Metropolitan through its 27 member agencies. The primary sources of Metropolitan's water supply are the Colorado River Aqueduct (CRA) and California's State Water Project (SWP). Currently, planning and design level studies are underway by Metropolitan to expand the water storage and conveyance systems within the service area for the purposes of providing increased efficiency and flexibility to manage limited water supplies, improving water quality, and increasing system reliability. The system reliability issue is particularly significant because the conveyance facilities from both the CRA and the SWP must cross the active San Andreas fault. This fault is considered to be the source fault for the anticipated "Big Earthquake" in southern California. To meet these objectives, Metropolitan's expansion plans involve a major new storage reservoir, new large diameter pipeline and tunnel conveyance facilities, more efficient utilization of existing groundwater basins, and an aggressive public awareness and conservation program. This paper focuses on the planning studies that have been carried out for over 50 miles of tunnels being considered for several of Metropolitan's proposed conveyance systems. These tunnels have ranged in length from a few hundred feet to over 42,000 feet, with depths of cover ranging from a few tens of feet to over 3,000 feet, and finished diameters ranging from 10 to 20 feet.

Jan 1, 1993

By Jan K. Wolski

Detection of the air recirculation branches within a large ventilation network may be difficult, therefore a PC computer routine has been developed to perform this task in an efficient and reliable manner. This paper describes the method illustrated using a network with complex multi-recirculation circuits. The fact that only the air flow directions and not the flow rates are used in calculations is of some interest. The air recirculation during a real mine fire is demonstrated using the PCVENT program, whose version 4.0 includes current information about any recirculation branches during network calculations or during a fire simulation. This paper also discusses some transient problems related to air recirculation, and gives examples.

Jan 1, 1993

Gold heap leach operations often process low grade ores with little margin for cost increases. The advantage of heap leach operations is the considerable savings in both capital and operating costs. This paper looks at an alternative pH modifier to lime in the heap leach process, namely bauxite waste mud or red mud. The red mud can contain trace amounts of gold and was found to be an excellent source of slow release sodium hydroxide for long-term pH modification. Column cyanide leaches showed that 25 kgt-1 of red mud provided a higher pH and longer pH modification than 0.25 kgt-1 of lime. Contaminants leached from the red mud hampered the adsorption of the aurocyanide complex onto activated carbon.

Jan 1, 1993

By K. L. Wiley

In-situ leaching, initiated in 1986 at San manual, was economically developed in 1989. The primary reason for this lag time between startup and viable production was the time required for technical development. The technical development pursued comprised detailed design, development, and implementation of in-situ well construction methods, formulation of suitable well pattern arrays, and the development of extensive hydrogeologic and geochemical knowledge of the mineral deposit. Since 1989, the in-situ leaching program has become a viable and cost effective method to extract copper from the supergene mineralized zone of the San Manuel deposit. The in-situ leaching methods that are currently utilized have been progressively expanded and continually developed and will became the cornerstone of copper production from the San Manuel oxide mineral deposit. This paper presents an overview of the supergene hydrogeology, current design techniques, drilling methods and well completion, pump determination and setting, solution management, and future plans for the increased extraction of copper by in-situ leaching methods at the San Manuel mine.

Jan 1, 1993

By Brij M. Moudgil, Shoulian Zhu, J. L. Pinault

A new technique, prompt neutron activation probe (PNAP), for analyzing phosphate rock slurry in-situ was evaluated both in the laboratory and at the plant. The technique yielded a high precision in the analysis of Ca, Si and H using 252Cf source. Low accuracy of the direct measurement of P using 241Am/Be in the laboratory tests was attributed to the interference of rare earth elements present in the samples, particularly Gadolinium. No significant effect of variables such as solids loading, particle size distribution, and flotation reagents was observed on the probe performance. The probe can detect the compositional changes of the feed, tailings and the concentrate streams in the plant.

Jan 1, 1993

By M. S. Celik, G. Onal, S. Atak, A. A. Abramov

An oolitic phosphate ore composed of phosphate (mainly francolite) and carbonates as gangue has been tested for the suitability of the reverse flotation process. The samples were first ground autogeneously followed by the reverse flotation process. While the carbonates were floated by sodium oleate the phosphate was depressed by phosphoric acid. The effect of particle size, reagents type and concentration on flotation recoveries have been investigated to determine the optimum conditions. By this process, a run-of-mine ore containing 16.72 % P205 was upgraded to 28.00% P205 with a recovery of 77.0% The mechanism of optimum flotation with phosphoric acid observed at pH 6.3 is explained based on a relationship involving surface potentials and the ratio of required collector concentrations for the respective minerals.

Jan 1, 1993

By George P. Demopoulos, Vladimiros G. Papangelakis, Dimitrios Filippou, A. J. Monhemius, G. W. Warren, E. Peters

A new method developed for the estimation of the activity of Ht in mixed sulfate solutions is described and examples of application of this method to the system H2SO4-ZnSO4-FeSO4-Fe2(SO4)3 from 298 to 473 K are offered. The method makes use of an "extended Debye-Hiickel" type of equation that was originally put forth by Das for pure H2SO4 solutions at ambient temperature. The treatment of mixed sulfate solutions was made possible by combining that equation of Das with a speciation algorithm which calculates the abundance of all species formed. The developed method, which also takes into account ionic strength and temperature effects, was used to generate hydrogen ion activity and speciation data for all possible acid/metal sulfate pairs of the system H2SO4-ZnSO4-FeSO4-Fe2(SO4)3. Finally, under the light of the reported data, specific examples of hydrometallurgical reaction systems are analyzed in terms of thermodynamics or kinetics. In particular, the systems discussed are: hydrometallurgical precipitation of hematite, solvent extraction of Fe(III), acid leaching of zinc ferrite, and oxidation of Fe(II) to Fe(III) by O2(aq).

Jan 1, 1993

By A. S. Malicsi, Vathsala Rajagopal, I. Iwasaki

Corrosion and abrasion properties of a series of chromium-containing, cast-iron balls, with Cr contents ranging from 0% to 29%, were evaluated and compared with austenitic stainless-steel and mild-steel balls. Marked ball wear tests were performed on artificial ore samples consisting of 95% quartzite, with either 5% pyrrhotite or 5% chalcopyrite, under a nitrogen or oxygen atmosphere. The electrochemical mechanism was investigated by correlating the corrosive wear with the corrosion currents obtained from potentiodynantic polarization curves under abrasion. Flotation recoveries were determined on a 95% quartzite + 5% pyrrhotite sample ground with various cast-iron ball materials under an oxygen or nitrogen atmosphere. Electrochemical results are found to be in good agreement with flotation results and with corrosive wear data obtained from marked ball wear tests.

Jan 1, 1993

By J. Hanna, R. Kalathur

Over the years, Alabama's coal industry has generated, during mining and cleaning operations, about 150 million st of fine waste coal, with this total increasing at a rate of 2 million stpy. Reclamation of the fine-size wastes (containing 20% - 60% clean coal by weight) provides, free of charge, mined and crushed feed stocks for coal recovery. Also, the removal or recovery of pyrite from the tailings should eliminate a major source of acid-water pollution. Tests were made on the impounded wastes and current plant discharges to recover the coal fraction by sizing, gravity and flotation techniques. Gravity separation of the +100-mesh material produced commercial-grade coal averaging 7.6% ash, 0.8% sulfur and 13,471 Btu/lb. However, the coal yield, at about 31 % - 56%, was relatively low. Froth flotation, using mechanical and froth column methods, gave similar coal products at much higher coal recovery rates of 87% - 93%. This coal analyzed 10% ash and 1.1% sulfur.

Jan 1, 1993

By Thomas J. Feeley

The US Department of Energy (DOE) is supporting the engineering development of three advanced physical coal cleaning technologies: selective agglomeration, advanced flotation and advanced cycloning. Each is capable of significantly reducing the pyritic-sulfur content of US coals. The objective is to provide the coal and electric-utility industries with a cost-effective option for addressing the SO, emission reductions required by the 1990 Clean Air Act Amendments (CAA). A secondary objective is to evaluate the potential of advanced coal cleaning for removing trace elements that are precursors to the formation of hazardous air pollutants (HAS). The proposed National Energy Strategy (NEE) and the 1990 CAA lay a foundation for a more efficient and environmentally sustainable energy future (1991). The need to use energy resources in an environmentally sound manner presents critical challenges and opportunities for coal preparation during the next decade, particularly regarding the control of SOS and HAY emissions. The principal challenge is the development of cost-effective coal preparation approaches for sulfur and HAY precursor removal.

Jan 1, 1993

By M. J. Richards, T. X. Ren

Determination of the state of an underground fire plays an important role in fire fighting, rescue and reopening operations. This is normally achieved by the analysis and interpretation of fire gases taken from the fire zone. However, drawing conclusions from gas analysis is not an easy task and needs specialist skills, expertise and experience that are usually beyond the knowledge of the officials in a mine. The complexities of a mine fire and the uncertainties of available information often make effective fire fighting decisions difficult if not impossible. This paper describes a knowledge based expert system that can aid in the diagnosis of sealed coal mine fires. Using a commercially available shell, the expert system has been designed to accommodate a series of diagnostic rules replicating the reasoning logic that would be used by human experts. The system allows the diagnosis of explosibility of the fire zone and trends of various fire ratios to be easily visualised for decision making. By continuously analysing the incoming information, the system is able to provide a rapid assessment of the situation of a sealed mine fire prevailing under specific mining and geological conditions. In addition, short term trends in fire behaviour can be predicted and possible fire control actions recommended. An example is given and shows how this system can be used as an analytical tool in various ways to assist the combating of coal mine fires. Further development of the system is discussed.

Jan 1, 1993

By S. Todd Mickleborough

The geostatistical technique of conditional simulation is applied to measure the uncertainty in factor of safety predictions for soil slopes where there is incomplete knowledge of the spatial distribution of soil properties. A case study considers a natural clay slope in Canada. The sequential indicator simulation technique is used as a means for generating a series of spatial maps of soil properties for this site. These maps approximate random draws from the conditional probability density function that characterizes existing uncertainty in the spatial distribution. Factor of safety determinations are then made for each simulated map using the simplified-Janbu approach, where the computations are performed with a new computer program that can operate on irregular spatial profiles of soil properties specified on a discrete grid. A unique capability of this approach is the ability to generate the distribution of factor of safety conditional to the type, position, and value of existing site characterization measurements. This capability should reduce uncertainty in FS predictions.

Jan 1, 1993

By III Feeley

The U.S. Department of Energy is supporting the engineering development of three advanced physical coal cleaning technologies--selective agglomeration, advanced flotation, and advanced cycloning--capable of significantly reducing the pyritic-sulfur content of U. S. coals. The objective of this activity is to provide the coal production and electric-utility industries with a cost-effective option for addressing the SO2 emission reductions required by the 1990 Clean Air Act Amendments. A secondary objective is to evaluate the potential of advanced coal cleaning for removing trace elements that are precursors to the formation of hazardous air pollutants. This paper will summarize the status of the three advanced physical coal cleaning engineering development projects.

Jan 1, 1993