Search Documents

By J. Alfred Berger, O. M. Katz

The Zv-Hf-H ternary system was studied between 500° and 900°C at pressures less than 1 atm of hydrogen gas between 1 and 60 at. pct H. A new and unique microgravimentric apparatus was used. Cizanges of slope on pressure-hydrogen composition isothernis delineated phase boundaries. These boundaries separatecl the three regions, a, 0, and y—so designated to correspond to the regions of the Zr-H binary system—from the multiphased areas between them. A eutectoidal decomposition was found with the ß region phase or phases decornposing into a lamellar product on quenching to rool ter,zperatuve. Reproducible decomposition-pressure hysteresis occilrved lnainly at lower hydrogen cornpositions and at lower temperatures across multiplzase vegions between a and 0 and a and y. Tire effects of hqfniur7z on the hydriding charactevistics of zirconiurrz weYe as follows: 1) stabilization of the a and y vegions while destabilizing the 0 region; 2) a/?preciable elevation of the decomposition pressrkres in the multiphase region between the a and /3 field; 3) ~nouenzent of the eutectoid reaction to high te~nperatures; 4) reduction in the total qiiantity of hydrogen absorbed under one atmospheve of Hz p7-essure; and 5) introduction of a split deconzposilion at the eiitectoiclal poinl in pa?? of the ternavy. Assuru~ptions based on an ir-2terstitial vandonl-solulion rtioclel 0.f hydrogen in metals slzowed that the bindit~g energy between solute sites prednnzinatecl at low /i?!dvogen concentrations. However, at high hydrogen contents the entropy was the predorninatlt factor in determining the stability of the Zr-Hf-H al1o.s. This was interpreted to mean a scarcity of filrtlzer itltevslilinl solute sites caused by hydrogen-hydvogen intet-actions in the metal lattice. INTEREST in the reaction of hydrogen with metals has increased in the past few years for the following reasons: 1) the formation or use of high hydrogen potential environments in nuclear reactors; 2) the reaction of hydrogen with alloys in nuclear reactors with the accompanying deleterious effects on the mechanical and corrosion properties; 3) the theoretical implications of thermodynamic data on the theory and rules of alloy formation in the metal-hydrogen systems; 4) the use of hydrogen-containing fuels in rocket engines; 5) the need for a process of making fine metal powders of high-melting reactive metals; and 6) the beneficial impregnation of superconducting alloys with hydrogen. In nuclear pressurized-water reactors, the problem exists of limiting the hydrogen pickup of zirconium alloys which are utilized as fuel cladding, heat shields, and support members. In general, zirconium alloys have good mechanical and corrosion-resistant properties in high-temperature water. However, hydrogen is absorbed from the corrosion reaction between metal and water, greatly accelerating the formation of the corrosion product ZrOz as well as mechanically embrittling the underlying metal. In addition, recent observations1 at zirconium to hafnium welds showed that secondary elements in zirconium can have an appreciable, and somewhat unexpected, effect on hydrogen absorption. This paper lists the thermochemical data in the range 500" to 900°C for the equilibrium reaction of four high-purity Zr-Hf alloys with hydrogen. Phase boundaries and thermodynamic functions are determined while the structural data will be presented in a future paper. In general, the Zr-Hf-H system approximates the well-known, eutectoidal, Zr-H diagram2,3 with modifications introduced through the behavior of hafnium.4,5 The Hf-H system,' published while this work was in progress, provided a consistent trend with the Zr-Hf-H data. PREPARATION OF Zr-Hf ALLOYS Table I presents a complete flow chart of the preparation procedure. The zirconium and hafnium crystal bars were completely immersed in high-purity kerosene and slowly cut into thin wafers. Wafers were then cold-sheared into approximately 1-g pieces, thoroughly cleaned, weighed, and inserted into the furnace. The alloys, B-2, B-4, B-6, and B-8, were then nonconsumable arc-melted under 500 mm of purified argon. Additional purification of the argon was accomplished by melting a large titanium button each time an alloy was re-melted or a different alloy melted. Each alloy button, which weighed 25 g, was remelted four times in an approach to complete homogeneity. Material losses were less than 0.02 wt pct. Alloy buttons were alternately cold-rolled and vacuum-annealed into 10- and 20-mil sheets. Table I1 gives the composition of the four alloys used. Very little elemental segregation existed be-

Jan 1, 1965

By G. Derge, Ling Yang, G. M. Pound

The specific conductance and its temperature dependence were measured over the entire composition range of the molten Cu2S-CuCI system. At a typical temperature of 1200°C, 10 rnol pet of the ionically conducting CuCl reduced the specific conductance from about 77 ohm-lcm-l for pure Cu2S to about 32 ohm -1cm -1, and 50 mol pet CuCl reduced the conductance to that for pure CuCI—about 5 ohm 1cm1. The nature of electrical conduction in molten Cu2S, FeS, CuCI, and mixtures was studied by measuring the current efficiency of electrolysis at about 1100°C. The Cu2S, FeS, and mattes were found to conduct exclusively by electrons, but addition of 1 5 wt pet CUS to Cu2S produces a small amount of electrolysis. Addition of CuCl to Cu2S suppresses electronic conduction, and ionic conduction reaches almost 100 pet at a CuCl concentration of about 50 mol pet. These facts are interpreted in terms of electron energy level diagrams by analogy to the situation in solids. RESULTS of electrical conductivity studies on molten Cu-FeS mattes as a function of composition and temperature have been reported.' The specific conductances ranged from about 100 ohm-' cm-' for pure Cu2S to 1500 ohm-' cm-1 for pure FeS. This is in sharp contrast with the low specific conductance of molten ionic salts for which the transfer of electricity is by migration of ions in the field. In general, these ionically conducting molten salts, such as NaC1, KC1, CuC1, etc., have a specific conductance of the order of magnitude of 5 ohm-' cm-'. It was concluded on the basis of this evidence that molten FeS and Cu,S exhibit electronic conduction. Pure molten FeS has a small negative temperature coefficient of specific conductance, resembling metallic conduction, while pure molten Cu2S has a small positive temperature coefficient, resembling semi-conduction. The molten Cu2S-FeS mattes follow a roughly additive rule of mixtures, both with respect to specific conductance and temperature coefficient. Savelsberg2 has studied the electrolysis of molten Cu2S and Cu2S + FeS. He concluded that while molten Cu2S is an electronic conductor, there is some ionic conduction in molten Cu2S + FeS3 owing to the formation of the molecular compound 2Cu2S.FeS and its dissociation into Cu1 and FeS2-1 ions. The present work does not verify his results. Chipman, Inouye, and Tomlinson" have studied the specific conductance of molten FeO and report a high specific conductance, about 200 ohm-1 cm-1 of the same order of magnitude as that found for molten mattes, and a positive temperature coefficient. They interpret these results in terms of p-type semiconduction in the ionic liquid by analogy to the situation in solid FeO.1 imnad and Derne' detected appreciable ionization in molten FeO by means of electrolytic cell efficiency measurements. In order to verify the conclusion that electrical conduction in molten Cu2S and mattes is electronic, and to gain further insight into the structure of molten sulfides, the following investigations were carried out in the present work: 1) The specific conductance, s of the molten system Cu2S-CuC1 was measured as a function of temperature over the entire composition range. As discussed later, molten CuCl is an ionic substance. It was thought that if molten Cu2S were simply ionic in nature, addition of small amounts of CuCl might not have a catastrophic effect in lowering the high conductance of the Cu2S. On the other hand, if much electronic conduction occurs, addition of the ionic CuCl should have a large effect in destroying the electronic conduction. 2) The electrolytic cell efficiency of the following molten systems was measured at about 1100°C in specially designed cells: Cu3; Cu2S + FeS, 50:50 by wt; FeS; Cu2S + CuS, 15 wt pet; Cu2S + CuC1, 5.9 to 46.4 mol pet; and CuC1. This gives a direct measure of the fraction of current carried by ions in these melts. Further, the cell efficiency, extrapolated to zero ionic current, is given by cell efficiency = (s leasile + s elexstronic). [1] s lucile for molten CulS would be expected to be no greater than that for molten CuC1, whose s lonle is about 5 ohm-' cm-1, as will be seen in the following. u,.,,.,.,.......for molten Cu,S is of the order of 100 ohm-' cm-'.' Thus, a large increase in cell efficiency from 0 to values of 10 to 100 pet upon addition of CuCl to Cu2S would indicate destruction of the electronic conductance. Conductance Measurements Experimental Procedure—The apparatus and experimental method were the same as those described in detail in connection with the study of electrical conduction in molten Cu,S-FeS mattes.' A four terminal conductivity cell and an ac poten-

Jan 1, 1957

By C. W. Beattie, R. L. Solter

ALUMINUM-KILLED, low carbon steel sheets are used extensively for severe deep drawing and other difficult forming operations. They usually, but not always, have a characteristic grain structure in which the grains are elongated both in the lengthwise and in the transverse direction. As described by Burns and McCabe,&apos; a typical grain in the plane of the sheet has its two axes in that plane from 1 Y2 to 4 times as long as the axis normal to the plane of the sheet. Rickett, Kalin, and MacKenzieZ have also reported on the recrystallization behavior of such steel. The contrast in grain structures of fully processed sheets of aluminum-killed and rimmed steel is illustrated by Figs. 1 and 2. The elongated grain structure of the aluminum-killed sheet is not developed on all heats or lots of this metal, and studies of the factors controlling and influencing its formation are reported in this paper. Jeffries and Archerb tate that unstrained grains are normally equiaxed, but exceptions are common. For example, if a metal containing a material mechanically obstructing grain growth is subjected to considerable working followed by thorough annealing, it may exhibit grains consistently elongated in the direction of working. Our experiments demonstrate that aluminum-killed, low carbon steel is such a metal, and that the substance mechanically obstructing grain growth is aluminum nitride. The effectiveness of aluminum nitride in inhibiting grain growth has been found to be influenced by the degree of cold reduction, the rate of heating in annealing, the thermal history of the sample before cold reduction, and the residual aluminum content. A correlation between grain shape and austenitic grain coarsening temperature also was indicated and additional experiments demonstrated that aluminum nitride is also the principal cause for the fine grain characteristic of aluminum-killed steels. Manufacture In conventional practice, aluminum-killed sheet steel is manufactured from a low carbon steel containing approximately 0.02 to 0.07 pct residual (HC1 soluble) Al. With the exception of certain samples containing greater or lesser amounts of aluminum, the steels used in these investigations were within the following composition range: C, 0.03 to 0.06 pct; Mn, 0.28 to 0.38; S, 0.017 to 0.032; Al, 0.03 to 0.06; P, <0.01; and Si, <0.01. Properly heated ingots are rolled to slabs about 4 in. thick. After surface conditioning, the slabs are reheated to about 2300°F and hot rolled continuouslv to strip about 1/10 in. thick. The strip rolling is completed at a temperature of 1550°F or higher, and the strip is coiled, usually at a temperature near the lower critical transformation. After cooling, the strip is pickled to remove oxide, cold reduced 40 to 70 pet to final thickness, then annealed to 1250° to 1350°F in 20 to 80 ton charges, the size of which results in slow heating and cooling rates. Effect of Cold Reduction According to Sachs and Van Horn,&apos; the deformations of the individual grains in rolling are similar to those of the total volume. Thus individual grains would elongate in rolling according to the amount of cold reduction imposed. This is true theoretically, but as cold reduction increases the individual grains tend to fragment, and measured grain elongations become less than theoretical. The amount of grain elongation may be described by a numerical rating based on grain counts made by the intercept method. Specimens are polished normal to the plane of the sheet, with the polished surface extending parallel to the rolling direction. After etching, grain intercepts are counted along a 50 mm line on a micrograph of suitable magnification. In random locations parallel to the plane of the sample 20 counts are made and 20 are made in the thickness direction of the sample the average count in the thickness direction divided by the average count parallel to the plane of the sample gives a numerical rating of the grain shape called grain elongation. For example, a grain elongation of 2.00 means that the average grain is twice as long as it is thick. The average of both counts may be converted to grains per sq mm by a nomograph relating intercept counts and grain count. By the same procedure the grain elongation in the plane of the sheet but transverse to the rolling direction may be determined, using transverse metallographic samples. A comparison of theoretical and measured grain elongation was obtained on an aluminum-killed

Jan 1, 1952

By H. I. Aaronson, C. Wells

Configurations of ferrite crystals have been found in a plain carbon steel which appear to have resulted from the nucleation of new ferrite crystals at the interphase boundaries of previously formed crystals despite the high carbon concentrations which necessarily develop at these boundaries. This phenomenon has been termed sympathetic nucleation. An attempt has been made to reconcile the occurrence of sympathetic nu-cleation with current nucleation theory. THIS investigation is one of a series on the formation of proeutectoid ferrite from austenite. From the viewpoint of chemical composition, this reaction consists of the nucleation and diffusional growth of crystals of carbon-poor ferrite within a matrix of carbon-rich austenite. The austenite adjacent to the austenite-ferrite boundaries will be greatly enriched in carbon, approximately to the value of the y/(a + y) equilibrium curve or its metastable extrapolation at the temperature of transformation. Those areas of austenite appreciably farther removed from the growing ferrite, on the other hand, will be relatively unaltered in composition, especially at the earlier stages of transformation. Since rates of nucleation are considered to decrease exponentially with decreasing supersaturation,&apos; the frequency with which ferrite nuclei appear at austenite-ferrite boundaries should be negligible in relation to that at which they form in other regions of the austenite. During this investigation, however, many groupings of ferrite crystals have been found which appear to have resulted from the nucleation of ferrite at austenite-ferrite boundaries. This phenomenon has been given the name of sympathetic 71.1tcleation. A number of micrographs of morphological configurations caused by sympathetic nucleation will be presented, after which an explanation for this reaction will be proposed in terms of current nucleation theory. Some of the structures to be considered are composed of bainite, an aggregate of ferrite and carbide, rather than of ferrite. Since ferrite and bainite differ only in that bainite forms under conditions which result in the nucleation of carbides behind the advancing austenite-ferrite boundaries,&apos; it will usually be unnecessary, for the purpose of this paper, to distinguish between the two reaction products. All studies were performed on an electric furnace steel (obtained from the Vanadium Alloy Steel Co.) containing 0.29 pct C, 0.76 pct Mn, 0.25 pct Si, 0.005 pct P, and 0.007 pct S. The alloy was cast as a 150 Ib, 7x7 in. cross section ingot and forged into bars 2x2 in. in cross section. These bars were homogenized for 48 hr at 1250°C in an Endo-Gas atmosphere. The depth to which decarburization penetrated during this heat treatment was determined by chemical and microscopic analyses and the affected metal was removed by machining. Specimens for isothermal transformation studies were cut from the remaining material; most of these specimens were 1/2x1/4X1/16 in., though some with a thickness of 1/32 in. were prepared for use at the shorter reaction times and lower reaction temperatures. Specimens were austenitized for 30 min at 1300°C, isothermally reacted for various times at temperatures ranging from 775" to 475 "C, and then quenched in iced water. The austenite grain sizes within individual specimens ranged from ASTM Nos. 1 through —4. A commercial heat-treating salt which was continuously deoxidized by an immersed graphite crucible served to minimize the loss of carbon during austenitizing; thick covers of powdered graphite and immersed graphite rods effectively prevented decarburization in the lead pots employed for the isothermal reaction treatments. The heat-treated specimens were sectioned and mounted in Bakelite. Following the completion of standard grinding and mechanical polishing procedures, the specimens were electrolytically polished with a Buehler-Waisman apparatus and etched in 2 pct nital. Experimental Results Rules of Evidence for Sympathetic Nucleation—On the basis of observations made on a single plane of polish, one precipitate crystal may be considered to have been sympathetically nucleated at the inter-phase boundary of another precipitate crystal when the following conditions are fulfilled: 1) The sympathetically nucleated crystal is not in contact with a grain boundary or a subboundary in the matrix phase. 2) The shape, size, and location of the crystal at whose boundary sympathetic nucleation occurred (hereafter termed the base crystal) and the crystal formed by sympathetic nucleation substantially pre-clude the possibility that the plane of polish em-ployed may have concealed the fact that both crys-tals actually nucleated at a grain boundary or a sub-boundary in the matrix phase.

Jan 1, 1957

By Charles F. Hickey, Eric B. Kula

Thermomechanical treatments applied to the maraging steels include a) cold working in the austenitic condition at 650°F, followed by transformation to martensite and aging, b) cold working in the murtensitic condition and aging, and c) cold working in the aged condition with and without subsequent reaging. The strength increases in these steels are very small compared to the increases observed in conventional carbon and alloy steels. The changes that are observed are compatible with the strengthening mechanisms operative during thermomechanical treatment of conventional steels, however. Differences are caused by the absence of a carbide precipitate and the low work-hardening rate in both the solution-treated and the aged conditions. ThE 18 pct Ni maraging steels represent a class of steels which are finding great interest for high-strength applications.1~2 They are essentially carbon-free, and contain 7 to 9 pct Co, 3 to 5 pct Mo, and 0.2 to 0.8 pct Ti. Although austenitic at elevated temperatures, they can be air-cooled to room temperature to form a martensite, which because of the absence of carbon is relatively soft. On subsequent reheating age hardening occurs and strength levels of 250 to 300 ksi yield strength can be attained. These steels appear to be particularly suitable for studying the response to various thermome-chanical treatments for additional reasons other than the obvious one of attempting to improve their already attractive properties. Thermomechanical treatments can be defined as treatments whereby plastic deformation, generally below the recrystal-lization temperature, is introduced into the heat-treatment cycle of a steel in order to improve the properties. With an absence of intermediate transformation products on air cooling the maraging steels have good hardenability and hence can readily be cold-worked in the austenitic condition prior to transformation to martensite. Further, they can be worked in the martensitic condition prior to aging, and even can be deformed in the fully aged condition. Finally, it is of interest to compare their re- sponse to that of the more conventional alloy and carbon steels, where the role of carbides is important in the strength increase by thermomechani-cal treatments. The thermomechanical treatment of conventional steels has been the subject of a recent review.&apos; I) MATERIALS AND PROCEDURE The steel used in this investigation was a commercially produced vacuum-melt heat, which had been rolled to 0.090 in. and mill-annealed. The composition of the alloy was as follows: 0.02 C, 0.08 Mn, 0.10 Si, 0.009 P, 0.009 S, 18.96 Ni, 7.34 Co, 5.04 Mo, 0.29 Ti, 0.05 Al, 0.004 B, 0.01 Zr, and 0.05 Ca. Unless otherwise stated the heat treatments used were the standai-d solution treatment at 1500°F for 1 hr, air cool, followed by a 900°F, 3 hr age. In this condition, the material exhibited 232 ksi yield strength and 239 ksi tensile strength. Mechanical properties were determined by Vicker&apos;s hardness measurement (20 kg) and by tensile tests on standard 1/2-in.-wide, 2-in.-gage-length sheet tensile specimens. Notch tensile tests were run using the 1-in.-wide NASA type, edge-notched specimen.4 Fracture-toughness determinations were made on 3-in.-wide, center-notched, fatigue-cracked specimens, following the recommendations of the ASTM Committee on Fracture-Toughness Testing.4 An electric-potential technique was used for measuring the crack size at the onset of rapid crack propagation5 which is necessary for calculations of Kc, the critical stress-intensity factor under plane-stress conditions. The critical stress-intensity factor under plane-strain conditions KI, was also calculated, using the stress at which the first observable crack growth occurred. 11) RESULTS A) Cold-Worked in the Austenitic Condition. The reported M, temperature for the 18 pct Ni maraging steel is about 310°F.1 Therefore, a temperature of 650°F was selected as suitable for rolling in the austenitic condition. Specimens were solution-treated at 1500°F for 1 hr, air-cooled to 650°F, and rolled varying percentages from 0 to 60 pct, at 20 pct reduction per pass. Tensile and hardness properties after aging at 900°F for 3 hr are shown in Fig. 1. The tensile strength increases from 253 to 271 ksi and the yield strength from 247 to 265 ksi as a result of a reduc-

Jan 1, 1964

By H. C. Gatos, A. D. Kurtz

WITH the growing interest in the mechanism of self-diffusion of metals, the study of accurate and convenient methods for determining self-diffu-sion coefficients appears highly desirable. It was with this objective in mind that the present investigation was undertaken. Gatos and Azzam1 employed an autoradiographic technique for measuring self-diffusion coefficients of gold. This method involved sectioning of the specimen through the diffusion zone and recording the radioactivity directly on a photographic film. Because of the very short range of the emitted ß rays in gold, the activity recorded on the film was essentially the true surface activity. With proper choice of the sectioning angle, sufficient resolution could be obtained and the entire concentration-distance curve recorded in one measurement. For the boundary conditions of the experiment, where an infinitesimally thin layer of radioactive material diffuses in positive and negative directions into the end faces of a rod of infinite length, the solution of the diffusion equation is C/Cn = 1/v4pDt exp (-x2/4Dt) where C is the concentration of diffusing element (photographic density in this case), C,, is the constant (depending upon amount of radioactive material), x is the diffusion distance, D is the diffusion coefficient, and t is the time. Thus, by plotting the logarithm of the concentration vs the square of the diffusion distance, a straight line results and the slope contains the diffusion coefficient. In this manner, the self-diffusion coefficient of gold can be obtained as a function of temperature. In the present investigation the results reported by Gatos and Azzam1 have been verified, and the autoradiographic technique has been further developed and applied for the determination of the self-diffusion coefficient of gold at a number of temperatures. Furthermore, the energy of activation for the self-diffusion of gold has been conveniently determined. . Experimental Techniques Preparation of Specimens: The inert gold of high purity was received in the form of a rod from which cylinders were cut and machined to a diameter of 0.500 in. The specimens were annealed to a suitably large grain size and the faces were surface ground prior to the deposition of the radioactive layer. The radioactive isotope Au198 was chosen. It was produced in the Brookhaven pile by means of the reaction Au197 + n ? Au108. It decays by ß emission (0.96 mev) to Hg108 with the subsequent emission of a y ray (0.41 mev). 70Au 108 ? 80Hg 108 + -1e°. The half life of the Au108 is 2.7 days so that a strict time schedule had to be maintained in order to secure sufficient activity until the end of the experiments. For this reason, initial activities as high as 10,000 millicuries per gram were used. The gold arrived in the form of foil and was evaporated onto one face of each gold specimen cylinder to a thickness of about 100A. A sandwich-type specimen was formed by welding two such cylinders together. Evaporation of Gold: The gold was evaporated under vacuum from heated tantalum strips which were bent in such a way as to limit the solid angle through which the gold was allowed to vaporize, thus insuring a more efficient utilization of the gold. The specimens rested on flat brass rings which had an inner diameter of 0.475 in. The entire specimen-holding assembly could be manipulated from outside the vacuum system by means of a magnet which attracted a slug of soft iron attached to the assembly. By evaporating inert gold on glass slides under conditions identical to those employed for the radioactive gold, it was found that the thickness of the films was about 100A. Welding: The welding was performed by hot pressing in a stainless steel cylinder. The inside of the cylinder was threaded and fitted for two plugs. The specimens to be welded were placed in the middle of the cylinder and two pressing disks, one at each end, were inserted to avoid shearing stresses as the plugs were tightened. Mica disks were placed between the pressing disks and the specimens to prevent them from welding. The plugs were then tightened with a hand wrench and the entire unit was placed in an argon stream for about an hour to remove the oxygen. The unit was then inserted in the center of an argon atmosphere furnace maintained at about 700°C and left there for about an hour. Because of the difference in the temperature coefficient of expansion of the two metals, as the temperature rose. the pressure on the specimen-rollple increased and a weld resulted Welding was generally satisfactory under the conditions described.

Jan 1, 1955

By W. A. Turcotte, A. D. Paananen

Introduction The large reserve of fine grained oxidized iron-formation at the Tilden mine has been the object of research and development efforts to concentrate the iron oxides as far back as 1949. Due to the nonmagnetic nature of the ore and the fine grinding required to liberate the iron oxide minerals, this crude ore was not amenable to concentration by conventional methods. The iron oxides of the Tilden, ore body have a grain size of less than 25 microns and recovery of the finer, well-liberated iron oxides is essential. Conventional methods of desliming employing cyclones or thickeners were not feasible because of the excessive loss of iron oxides in the finer fractions. Development of selective flocculation-desliming was a key to commercialization of the process. Operations started in late 1974 with Algoma Steel Corp. Ltd., J & L Steel Corp., The Steel Company of Canada Ltd., Wheeling-Pittsburgh Steel Corp., Sharon Steel Corp., and The Cleveland-Cliffs Iron Co. as participants. Cleveland-Cliffs operates and manages the operation. Development of the Tilden Flowsheet The geology and ore reserves of the Tilden mine have been detailed in a paper by Villar and Dawe (1975). A joint program was undertaken in 1961 with the US Bureau of Mines in Minneapolis using the flowsheet developed by the Bureau employing the selective flocculation-desliming and calcium activated anionic silica flotation method (Frommer, et al, 1966; Frommer, 1964; Frommer, Wasson, and Veith, 1973). During this time, parallel testing at Cleveland-Cliffs Research Laboratory and Pilot Plant centered on the same type of desliming but was followed by the cationic flotation of silica with amine collectors (Columbo and Jacobs. 1976). The cationic silica flotation system was eventually chosen for its overall efficiency and simplicity. Regardless of the flotation method chosen, the technique of selective flocculation-desliming prior to flotation is the key to the success of the process. The flowsheet is described in detail by Villar and Dawe (1975). [Figure 1] shows a simplified one-line flowsheet of the Tilden concentrator. A total tailings thickener has been added to the original flowsheet and was placed in operation in 1978. The total-tailings thickener overflow reports to the reuse water pond and the underflow is pumped approximately 8 km (5 miles) to a storage basin. A flowsheet of the reuse water system is shown in [Fig. 2]. Selective Flocculation-Desliming Data have been published on the mechanisms and factors affecting selective flocculation in iron oxide-silica systems. The intent of this paper is not to discuss the theoretical aspects of selective flocculation, but rather to present experience gained from the commercial Tilden operation and from bench and pilot plant testing of fine-grained oxidized iron ores. From the bench and pilot plant testing prior to plant startup, certain reagent combinations and rates for the commercial Tilden plant were established. In the experience gained from three years of plant operation at Tilden, some of these reagent dosage rates have required significant adjustments due to changes in reuse water quality and to meet the requirements of varying ore types. Reuse Water The process water quality is a major concern at the Tilden mine and is constantly being monitored for selected chemical and physical characteristics. This monitoring has continued on a regular basis in order to gain a more thorough understanding of the interactions taking place in a dynamic water system and particularly as water quality is influenced by seasonal variations. Control of the reuse water chemistry is essential to the Tilden process both in the selective flocculation-desliming and flotation stages of concentration. With roughly 75% of the reuse water used in grinding-desliming operations, it is readily apparent that the biggest "reagent" in the selective flocculation-desliming process is water. Not enough can be said about the close control that must be exercised on the overall reuse water system. Control of the chemical treatment of the feed to the total tailings thickener is of utmost importance in order to produce a reuse water for the concentrator that is compatible with all stages of the concentrating process. There are many analyses made which aid in judging the quality of the water. Some of these are shown in [Table 1]. Five are particularly important and are monitored daily so that reagent adjustments can be made as required: suspended solids, calcium hardness, pH, dissolved silica concentration and temperature.

Jan 1, 1981

By Sandford S. Cole, John S. Breitenstein

The recovery of over 80 pct of the vanadium values in titaniferous magnetite from Maclntyre Development,Tahawus, N. Y., was accomplished by an oxidizing roast with Na2O3-NaCI addition. Process description is given for leaching of roasted ore and precipitation of V2O5 and Cr2O8 from leach liquor. THE exploration and development of the Mac-Intyre orebody at Tahawus, N. Y., by the National Lead Co. provided a source of vanadium. Analyses of various composite sections of the drill cores of the MacIntyre orebody were made to establish whether or not the vanadium was constant throughout. Ten drill cores were sampled as 50 ft sections, crushed, and a portion magnetically concentrated. The head and concentrate were analyzed for total iron and vanadium. The results on the concentrates indicated that the vanadium is associated with the magnetite and maintains a close ratio to the iron content. The nominal ratio of 1:25:140 of V: TiO2:Fe was found to exist in the concentrates. Typical value for the vanadium in the magnetite both from laboratory concentration and mill production is 0.4 pct. The recovery of vanadium from the magnetite was investigated in 1942 to 1943. The research program encompassed both laboratory and pilot-plant work on sufficient scale to provide adequate data to establish the feasibility of a full scale plant. The recovery of vanadium from various ores has been reported in the literature and has been the subject of many patents. The literature dealing with recovery from titaniferous ore by roasting is quite limited. Roasting with alkaline sodium chloride, sodium chloride or alkaline earth chlorides, and sodium acid sulphate have been claimed in various processes as effective means.1-8 The reduction of the ore, followed by acid leaching, was another method proposed.&apos;-&apos; "he use of various pyrometallurgical processes for recovery of vanadium in the metal or in the slag has also been extensively investigated, but the results had little application to the problem."-" The separation of vanadium values from subsequent leach liquors and vanadium-bearing solution has been the subject of a considerable number of papers and patents. The most practical is by hydrolysis at a pH of 2 to 3 by acidifying a slightly alkaline solution. Data on solubility of V²O5 and V2O4 in water and in dilute sulphuric acid indicated a solubility of 10 g per liter in water.&apos;" Laboratory Results Magnetite Analysis: Adequate stock of magnetite was provided so that the laboratory and pilot-plant operation was on ore representative of the mill production. The ore was analyzed chemically and examined by petrographic methods to ascertain whether the vanadium was present in combined state or as an interstitial component between grain boundaries. No evidence was obtained which would indicate that the vanadium was in a free state as coulsonite.15 The analysis of the ore was as follows: Fe²O³, 47.4 pct; FeO, 29.1; TiO,, 10.1; V, 0.40; and Cr, 0.2. The screen analysis of the ore on the as-received basis was: -20 +30 mesh, 28.8 pct; —30 +40, 18.9; -40 +50, 9.7; -50 +60, 15.1; -60 4-100, 5.9; -100 + 200, 11.2; -200 +325, 3.7; and -325, 7.2. Roasting Conditions: The prior practice indicated that a chloridizing roast with or without an alkaline salt had been effective on other titaniferous magnetites. On this basis roasts with additions of sodium chloride, sodium carbonate and mixtures thereof were investigated varying the roasting temperature between 800" and 1100°C. Since the ore had shown no segregation or concentration of vanadium, the influence of particle size on the freeing of vanadium by the reagents during roasting was determined. The initial work was on silica trays in an electric resistance furnace with occasional rabbling of the charge. Subsequently, the roasting was carried out in a small Herreshoff furnace to establish the influence of products of combustion on the recovery of the vanadium. The laboratory tests showed that this ore required an alkaline chloridizing roast, in conjunction with a reduction in particle size to less than 200 mesh. When roasted in air at 900 °C with 5 pct NaCl and 10 pct Na2CO³, over 80 pct recovery of the vanadium was attained as a water-soluble salt. The presence of alkaline earth elements gave detrimental effects and care had to be exercised to avoid any contamination of the ore or roast product by such materials. The solubilization of vanadium under the various conditions is given in a series of curves in Figs. 1 to

Jan 1, 1952

By Eckhard Nembach

The phase diagram of the system Pb-In has been investigated between -27° and + 40°C, using nzainly X-ray dijfraction. In accordance with t her mo dynamic measurements by Heumann and Predel, a segregation occurs at low temperatures, though not in the form of a nziscibility gap. THE phase diagram of the system Pb-In has been the subject of extensive investigations,1&apos;1 but recently Heumann and prede13 concluded from their thermodynamic data that a new feature should occur below room temperature. These authors observed that the maximum values for the enthalpy and entropy of mixing, which occurred at a composition of 50 at. pct Pb, were +400 and —1.7 cal per g-atom deg, respectively. From this the authors estimated that a miscibility gap should occur below 30°C, centered at 50 at. pct Pb. Resistivity measurements seemed to support this view. These authors proposed the phase diagram outlined in Fig. 1. Three phases exist at 30°C: the tetragonal indium phase with c/a > 1, the tetragonal intermediate phase a, with c/a < 1, and the fcc lead phase. During an investigation of the superconducting properties of Pb-In alloys. it has been observed4 that aging a specimen with 50 at. pct Pb for 14 days at -18°C decreased the superconducting transition temperature about 0.13"K and tripled the transition width. In this paper, the results of an investigation of the Pb-In phase diagram in the temperature range from — 2T to +40°C are reported. Superconductivity and X-ray methods have been used. 1) SPECIMEN PREPARATION The materials were provided by the American Smelting and Refining Co. According to the manufacturer their purity was 99.999 pct. The weighed amounts of the constituents were sealed in quartz tubes under an atmosphere of 10 torr helium, mixed for 24 hr in a rocking furnace at 380°C, quenched in ice water, and homogenized at 20" to 30°C below the solidus line, established by Heumann and Predel. The annealing times were 144 hr for specimens containing Less than 30 at. pct Pb and 36 hr for the remainder. 2) SUPERCONDUCTIVITY EXPERIMENTS The specimens were quenched from the homogeniza-tion treatment into ice water and their superconducting transition temperatures T, measured. The procedure used has been described in Ref. 4. The transition was detected by the change of the mutual induc- tance of two coaxial coils containing the sample. T, was defined as the temperature at which 50 pct of the total change in inductance had occurred. The repro-ducibility with which T, could be measured was i0.002"K. Then the specimens with lead contents between 38 and 75 at. pct were aged for 7 days at temperatures between -30" and 40°C. If this treatment caused T, to change by more than 0.005"K or the width of the transition to increase by more than 0.002"K, it was concluded that the specimen had undergone a phase change and no longer consisted only of the fcc lead phase: as it did immediately after homogenizing. The result is shown in Fig. 2. From this one can estimate at what temperatures and concentrations phase changes occur. The X-ray measurements were based on these preliminary results. 3) X-RAY EXPERIMENTS Because of the softness of the material, relatively coarse powders. 75 p, had to be used, which were filed in a helium atmosphere from homogenized specimens. The powders were annealed at least 30 min at temperatures between 120" and 16OJC, depending on their concentration, and quenched in ice water. Then their X-ray patterns were taken at -178°C with a Picker diffractometer, model 3488K, and a cold stage. on which the specimen was in thermal contact with a liquid-nitrogen reservoir. In this way the following relation was established for the fcc lead phase: a = 4.697 + 0.00247C for 40 5 C 5 75 11 where n is the lattice constant (A) and C is the at. pct of lead. The coarseness of the powder made it impossible to use lines with 0 > 75 deg; therefore n was averaged from lines with 45 deg 5 0 5 75 deg. The results were reproducible to within i0.05 pct. Relation [I] is very similar to the one found by Heumann and Predel at room temperature. Following this, homogenized specimens with compositions between 15 and 56 at. pct Pb were aged for at least 10 days at temperatures between -27" and

Jan 1, 1970

By Joe O. Ledbetter

INTRODUCTION Health physics as a profession really got a significant start during the Manhattan Project of World War 11. The Health Physics Society has recently published its 25th anniversary issue of the journal (June 1980). There was concern over radiation exposures during and after uranium production, especially about radium and its daughter products [Jackson 19401 and, as evidenced by the frequency of articles in the literature, there still is. The reason for this concern was expressed by Harley as "Workers engaged in the mining and pro- cessing of radium-bearing materials are exposed to dusts of the parent, to radon, and to the radon daughter products. In- haled radioactive particulates may be retained in the lung or redistributed to other organs of the body. Relatively minute de- posits of radioactive substances, particularly alpha emitters, have been clearly shown to be the etiological factor in a variety of injuries to industrial and re- search workers. " [Harley 1953] Emphasis in measurements has been placed on radium in water and radon in air, since these are the principal mobilized phases; however, it should be kept in mind that radium-containing particles do become suspended in air as aerosols and radon absorbs in liquids. Much of the uranium mining and production is being carried out aboveground. The principal difference between underground and surface (pit or leach) mining of uranium is the reversal in the relative importance of roles for the types of radiation dose. For aboveground the major radiation exposure is external gamma ray, whereas for underground it is internal alpha; for aboveground, the whole body penetrating is of greater importance than the lung alpha dose. AS a result of the politics involved and the law- suits for any and all diseases as being occupationally- caused, today , more than ever before, the successful performance of the activities connected with uranium production--before-, during-, and after-the-fact-- must include the provision of first class radiation protection. Such protection can be achieved by good measurements, thorough risk evaluations, and adequate controls. Meeting the ALARA (As Low As Reasonably Achievable) philosophy necessarily entails the determination of what is reasonable exposure. The necessary and sufficient elements of radiation safety under the ALARA dictum require a hard look at the dose versus effects data. There are times when the health physicist needs to make decisions of judgement rather than compliance with a well-defined regulation value. In order to facilitate such decisions, the real world must be separated from opinions that are merely artifacts of statistical variation and from the unprovable "what ifs" that are slanted to question the morality of any non-Luddite. UNITS VOCABULARY FOR DOSIMETRY There have been many radiation quantifying and dosimetric units introduced in the past. Fortunately, most of them did not catch on enough to become required knowledge for reading the health physics literature. The unit definitions necessary for our purposes here are the following: -curie (Ci)--unit of radioactivity equal to 3.7 x 10 10 disintegrations per second Webster&apos;s 19711 or the quantity of radionuclide that undergoes 3.7 x 10 nuclear transformations per second. Environmental levels of radioactivity are usually measured in picocuries (10-l2 Ci) per cubic meter for air and in picocuries per liter (pCi/~) for water and sometimes for air. .roentgen (R)--exposure dose of x or gamma rays that gives 1 esu of charge (either sign) to 1 cc of dry air @ STP. The roentgen is equivalent to an energy absorption of 86.7 ergs/g of air [Gloyna and Ledbetter 19691. .rad--radiation absorbed dose of 100 ergs per gram of absorber. The SI unit for absorbed radiation dose is the Gray; 1 Gy = 100 rads. orem--radiation absorbed dose of 1 rad times the quality factor (QF) for that radiation. The QF is 1 for x rays, gamma rays, beta rays, and posi- trons. For heavy ionizing particulate radiation, QF is a function of the amount of energy trans- ferred per unit length of travel, i.e. , the linear energy transfer (LET); the values of QF:LET in keV/um are as follows: 1:<3.5; 1-2:3.5-7; 2-5:7-23; 5-10:23-53; and 10-20:53-175 [Morgan and Turner 19 671 . For radiobiology, relative biological effectiveness (RBE) is recommended for use instead of the quality factor above that is for radiation protection: the RBE is the ratio of the dose of 200 kVp x rays to the dose of radia- tion in question (both in rads) to cause the same

Jan 1, 1980

By P. H. Lindon, J. C. Billington

Fe-O melts containing 0.045 pct 0 were deoxidized with Mn-Si-A1 alloys. Product compositions were reluted to the melt and alloy compositions and were found to be most sensitive to the aluminum content of the alloy. Low residual oxygen contents could be obtained when aluminum oxide was present in the Products because of the reduction of silica and manganese oxide activities. Flotation of the Products from a quiescent melt was followed both by analysis of the oxygen content and metallographic measurement of inclusion concentration. MnO-SiO2-A12O3 products were found to float most rapidly when their composition was such that their viscosity may be expected to be low. Changes in the particle size distribution indicates that particle coalescence occurred and differences in the degree of coalescence are thought to be responsible for the different flotation rates observed between products 0f differing composition. Measured flotation rates were slower than those Predicted from a model based on Stoke&apos;s Law, although alumina flotation might be reasonably accounted for by this model. Interfacial effects between oxide particles and the melt are believed to be responsible for the discrepancy. It has been recognized that deoxidation products constitute a large proportion of the nonmetallic inclusions present in killed steel. The amount of oxide inclusions which originate as deoxidation products depends largely upon three factors. These may be summarized, according to P16ckinger1 as: 1) Amount of primary products remaining in the steel prior to cooling. 2) Residual dissolved oxygen content of the steel after deoxidation. 3) Amount of secondary products, formed during cooling and solidification, which remain entrapped in the solid steel. In a well-deoxidized steel containing residual aluminum and/or silicon, the equilibrium dissolved oxygen content is usually very low and so the maximum amount of oxide which may be produced as secondary deoxidation products is small in comparison with the amount of primary products. It may be seen, therefore, that the amount of indigenous nonmetallic inclusions may be minimized if a low dissolved oxygen content is achieved by deoxidation and if the primary deoxidation products are efficiently removed. Oxides which originate by reaction of the metal stream with the atmosphere during teeming are not considered in the present study. It is known that two or more deoxidizers may result in a lower equilibrium oxygen content when used in conjunction with one another than when any of the individual deoxidizers are used alone. Equilibrium studies by Hilty and crafts2 and by Bell3 have shown that manganese increases the effectiveness of silicon as a deoxidizer, and Walsh and Ramachandran4 relate this to a reduction in the activity of silica in the products as the manganese :silicon ratio in the steel increases. It was also shown by Herty&apos;s work on deoxidation of steel by silico manganese alloys,5 that there existed an optimum ratio of manganese to silicon which gave a minimum inclusion content. This ratio was in the range 4:l to 7:l and the (FeO-MnO-SiO2) products formed by such deoxidation practice were found to lie in a composition range having very low liquidus temperatures (1170 to 1250°C approx). The optimum manganese:silicon ratio was then explained by postulating that these fluid products were able to coalesce and that the larger particles formed floated out of the steel very quickly as predicted by Stoke&apos;s Law. The present work examines the effectiveness of various Mn-Si-A1 alloys as deoxidizers and their effects on the composition and removal of primary deoxidation products from a quiescent melt. EXPERIMENTAL TECHNIQUE Approximately 250 g of prepared Fe-O alloy, containing 0.045 to 0.055 pct O, were melted in an alumina crucible and deoxidized at 1550°C by plunging a thin steel cartridge containing the deoxidizer below the melt surface. A high frequency induction furnace supplying current at 8.5 kHz was used to heat a graphite susceptor, the interior of which had been machined to give a wall thickness of 0.85 in. to form a receptacle for the alumina crucible. The iron melt was essentially quiescent as the induced current was concentrated at the external surface of the graphite susceptor by the skin effect. A nonoxidizing atmosphere was maintained over the melt by passing a continuous stream of argon through the lid of the susceptor. The melt temperature was measured before deoxidation, and again at the end of an experiment by means

Jan 1, 1970

By D. Atkinson, C. Bodsworth, I. M. Davidson

A geometric model of interstitial solid solutions, which has been used previously as a basis for the prediction of carbon activities in Fe-C austenite, is shown to serve also for the calculation of nitrogen activities in Fe-N austenite. The model has been developed to enable predictions to be made of the activities of an interstitial element in the presence of two host atom species. The activities calculated via the model are shown to be in satisfactory agreement with the measured values in the austenite phase for carbon in Fe-C-Co, Fe-C-Cr, Fe-C-Ni, Fe-C-~n, Fe-C-Si, and Fe-C-V alloys and for nitrogen in Fe-N-Ni alloys. The effect of the second substitu-tional solute on the logarithm of the activity of the interstitial element is expressed as the product of a constant mad the atomic concentration of that solute. The constants so derived we related to the thermo-dynamic interaction coefficients which describe the effect on the activity coefficient of carbon of an added solute element. In recent years the thermodynamic activities of carbon and nitrogen in the single-phase austenite field have been determined for iron binary alloys and for several iron-base ternary alloys. In order to extend the use of these measurements, it is desirable to be able to predict with reasonable accuracy the activities of the interstitials at compositions and temperatures other than those which have been measured experimentally. In all the systems studied to date, the interstitial elements do not conform to ideal behavior. Hence, the available data cannot be extrapolated or interpolated using the simple thermodynamic concepts of solutions. Several models have, therefore, been formulated for the purpose of predicting the activity of an interstitial element in the presence of one species of host atom. These models can be divided into the geometric1"5 and energetic6-&apos; types. The former group is based on the assumption that at low concentrations the activity of the interstitial species is determined by a composition-dependent configurational entropy term and an excess free-energy term which is temperature-dependent but independent of composition. The purpose of this paper is to show that the treatment, based on a geometric model, can be extended to enable predictions to be made of interstitial activities in the presence of two substitutional host atom species. THE CONFIGURATIONAL ENTROPY OF MIXING ICaufman5 has shown that the configurational entropy, S,, for a binary solution comprising of a host atom species, A, and an interstitial species, I, can be expressed as: where NI is the atom fraction of the interstitial species, R is the gas constant, and (2 - 1) is the number of interstitial sites excluded from occupancy by the strain field around each added interstitial atom. The number of interstitial sites per host atom, p, is unityg for the fcc austenite solutions considered here. The configurational entropy of mixing for a ternary solution comprising two substitutional atom species, A and B, and one interstitial species, I, can be derived similarly. Let the number of atoms per mole of each of these species in the solution be represented by «a, ng, and nI. From geometric considerations, it is improbable that the addition of a few atom percent of a second host atom species will change the type of sites (i.e., octahedral) in which the interstitial atom can be accommodated in the austenite lattice. At higher concentrations (determined largely by the relative atomic radii of the atomic species present and any tendency to nonrandom occupancy of the host lattice sites) other types of interstitial sites may become energetically favorable. Restricting consideration to compositions below this limit, for 1 = 1 the number of suitable interstitial sites is given by (n + nB). However, if each interstitial atom excludes from occupancy (Z - 1) additional sites, the total number of sites available for occupation is reduced to (n + ng)/Z. The number of vacant interstitial sites is given by: The total number of recognizable permutations of the atoms must include the recognizable, different configurations of the A and B atoms on the host lattice. Assuming that these arrangements are purely random, and are not affected by the presence of the interstitial species, the total number of recognizable permutations in the ternary alloy is given by: The configurational entropy is obtained by expanding, using Stirling&apos;s approximation, and collecting like items, as:

Jan 1, 1969

By H. R. Froning, R. O. Leach

In wertability alteration flooding, a chemical agent is rnoved through a reservoir by the flood water to increase oil recovery by decreasing the degree of wetting of the rock by the oil. Substantial amounts of the chemical may be lost during movement through the reservoir. The extent of the loss, and therefore the economics of the process, depends in some cases on factors which are difficult to reproduce in the laboratory. Therefore, a short-duration, low-cost field test method is needed to permit evaluation of chemical requirements under actual field conditions. This paper describes a small scale rest conducted at a single well for measuring chemical requirements, thereby giving a more reliable evaluation of this important factor in the applicability and economics of the process. In the rest a small wafer slug containing the chemical agent and a nonadsorbed tracer is displaced into the reservoir by a known volume of wafer. The well is then placed on producrion. Chemical loss per barrel of pore volume contacted is calculated from [he fractional recoveries of the agent tested and the nonadsorbed tracer. The method has been used to determine within the actual reservoirs the chemical requirements for both a sandstone and a dolomite reservoir. Several chemical agents are potentially available for wettability alteration flooding, although none is universally applicable. For some applications of the method, chemical costs per barrel of additional oil recovered can be substantially less than one dollar. INTRODUCTION Wettability alteration flooding provides a means of increasing oil recovery from reservoirs by decreasing the degree of wetting of the rock by the oil and increasing the displacement efficiency of the flood water. Earlier studies demonstrated a relationship between oil recovery during waterflooding and the degree of wetting of a rock surface by an oil. The application of wettability alteration flooding to the Harrisburg field of Nebraska provided a field test&apos; of this recovery process. Subsequently, additional laboratory and field tests have developed additional procedures for evaluating wettability alteration flooding, and have indicated where the process may be applicable. Applicability of this process to specific reservoirs is determined by a progression of tests to determine sus- ceptibility of the reservoir to alteration of its wettability, to indicate the degree of recovery improvement and to estimate the amount of chemical required to process the reservoir. The economics of applying improved oil recovery processes depends not only upon the degree of improvement in oil recovery achievable by the process but also upon the process costs and the timing of the income and the investment. Emphasis in this paper is on the expenditure aspects of the process. The work reported in this paper indicates that the chemical investments required for wettability alteration flooding are substantial. For evaluating the economics of a potential flooding application it is imperative that a sound estimate of the chemical requirements be made for the reservoir. Generally, true reservoir conditions are not adequately simulated in laboratory chemical propagation tests. Because of wide well spacings, many years might be required to obtain chemical propagation data from conventional pilots or inter-well tests. Consequently, n short-duration, low-cost method is needed to determine chemical requirements in the field. The potential applicability of wettability alteration flooding is discussed, as well as the economics of wettability alteration with respect to the inherent and imposed restrictions on the timing of income and investments. DETERMINATION OF CHEMICAL REQUIREMENTS In the process of moving a chemical bank through reservoir rock, some of the chemical agent lags too far behind the flood front to be effective or is otherwise lost to the reservoir system. The extent to which these losses occur overshadows the reductions in chemical concentration due to diffusion and to mixing with the reservoir fluids. Experience indicates that almost without exception, chemicals which induce a wetting change undergo either sorption reactions or chemical reactions with mineral constituents of the pore surfaces. Other reactions may occur between the added chemical and the reservoir oil and water. Even in limiting consideration to reactions of the relatively inexpensive inorganic salts, bases and acids, the reactions may be exceedingly complex. Reservoir pore surfaces consist of more than silica in sandstone reservoirs, and more than calcite or dolomite in carbonate reservoirs. Many mineral species are present, each exhibiting specific tendencies to react with an injected chemical. The reactions which occur can consume enough of the agent to have an important effect on economics. These reactions can cause a change in pH of the chemical bank, or may remove some of the active chemical by precipitation, adsorption or reaction to form a new chemical which may or may not be effective in

By D. Mills, G. B. Craig

ZIRCONIUM has been float-zone-refined in an electron-beam furnace and the redistribution of oxygen, iron, and tungsten has been measured. The iodide zirconium used in the present experiments initially contained both oxygen and iron in the range 100 to 200 ppm by weight, and tungsten in amounts less than 10 ppm. Float-zone refining of zirconium, using induction heating, has previously been attempted by Kneip and Betterton1 and Langeron.2 Kneip and Betterton were primarily interested in the removal of iron and nickel. They achieved some purification, with respect to both these elements, in material given up to six passes at 150 mm per hr under an argon atmosphere. Langeron reported purification for a large number of elements after four completed passes in a static vacuum system operating at pressures less than 10-6 mm of Hg and with rates of zone travel between 30 and 40 mm per hr. He did not report oxygen concentrations, but stated that there was inverse segregation of this element. westlake5 has also used a minimum of four zone passes to remove iron from zirconium. No rates or conditions were given. Belk6 has shown that tungsten contamination can occur during electron-beam melting. He reported an increase from 0.01 to 0.05 pct by weight tungsten in molybdenum after four complete zone passes. The vacuum system for the electron-beam unit used in the present investigation consisted of a single-stage rotary pump backing a liquid-air-trapped oil-diffusion pump. A pressure of less than 10-8 mm of Hg was obtained with Dow-Corning 705 fluid in the diffusion pump. In order to avoid contamination of the zirconium by evaporation from the tungsten filament, a special focusing cage4 was employed. Three rates of zone travel, 114, 38, and 4 mm per hr, were investigated, with the liquid zone moving from the bottom to the top of the bar. The bars used were 3 mm diam and the total melted length was 130 mm. Oxygen was analyzed by neutron-activation analysis using a neutron flux of 10&apos; neutrons per sq cm per sec to form the isotope N16 by the 016 (n,p) N16 reaction. The standard deviation is quoted for each oxygen determination. The iron and tungsten analyses were performed spectrographically, and the precision is estimated to be ±6 pct. Analyses for tungsten were all below the detectable limit of 10 ppm, confirming the protection given by the focusing cage. No significant redistribution of oxygen was found at the two higher rates of zone travel. The redistribution of oxygen and iron obtained after five passes at a rate of zone travel of 4 mm per hr (1.1 x 10-4 cm per sec) is recorded in Tables I and 11. Burris, Stockman, and Dillon3 have estimated the distribution of solutes during multipass zone refining. Using their curves for an effective distribution coefficient of Keff = 1.5 and 2 for oxygen and Keff = 0.3 for iron, the expected concentrations were estimated for the present material. These are shown in Tables I and 11, along with the experimentally measured values. The calculated concentrations are based on a molten-zone length of 10 pct of the total melted length, whereas in the present experiments the molten zone was approximately 5 pct of the total melted length. The effect of zone length on solute redistribution is most pronounced after a large number of zone passes. Comparison with Pfann&apos;s published data8 for solute redistribution for various Keff&apos;s and zone lengths indicates only small differences at low numbers of completed zone passes. It is evident that the expected distribution has not been realized in the case of iron. Scrapings of material deposited on the inner surfaces of the electron-focusing cage were found to be magnetic. It is, therefore, concluded that redistribution of iron is masked by evaporation. Deposition of iron inside the focusing cage was observed at all rates of zone travel. The results of the investigation may be summarized as follows: 1) Segregation of oxygen is typical for a solute with a distribution coefficient, Keff > 1. 2) No redistribution of oxygen takes place at high rates of zone travel. 3) The distribution coefficient for oxygen lies between 1.5 and 2.0. 4) Purification with respect to iron occurs mainly by evaporation. 5) The focusing cage is effective in preventing tungsten contamination.

Jan 1, 1967

By James K. Hallenburg

INTRODUCTION The delayed fission neutron, or DFN technique for uranium ore body analysis uses the first down-hole method for detecting uranium in place quantitatively. This technique detects the presence of and measures the amount of uranium in the formation. DFN TECHNIQUE DESCRIPTION The DFN technique depends upon inducing a fission reaction in the formation uranium with neutrons, resulting in an anomalous and quantitative return of neutrons from the uranium. Since there are no free, natural neutrons in formation, a good, low noise assessment may be made. There are several methods available for determining uranium quantity in situ. The method used by Century uses an electrical source of neutrons. This is a linear accelerator which bombards a tritium target with high velocity deuterium ions. The resulting reaction emits high energy neutrons which diffuse into the surrounding formation. They lose most of their energy until they come to thermal equilibrium with the formation. Upon encountering a fissile material, such as uranium, these thermal neutrons will react with the material. These reactions produce additional neutrons, the number of which is a function of the number of original neutrons and the amount of fissile material exposed. The particular source used, the linear accelerator, has several distinct advantages over other types of sources: 1. It can be turned off. Thus, it does not constitute a radioactive hazard when it is not in use. 2. It can be gated on in short bursts (6 to 8 microseconds). This results in measurements free of a high background of primary neutrons. 3. The output can be controlled. Thus, the neutron output can be made the same in a number of tools, easily and automatically. There are several interesting reactions which take place during the lifetime of the neutrons around the source. During the slowing down or moderating process the neutron can react with several elements. One of these is oxygen 17. This results in a background level of neutrons in any of the measurements which must be accounted for in any interpretation technique. These elements are usually uninteresting economically. The high energy neutrons will also react with uranium 238. However, the proportions of uranium 235 and 238 are nearly constant. Therefore, this reaction aids detection of uranium mineral and need not be seperated out. Upon reaching thermal energy the neutrons will react with any fissile material, uranium 235, uranium 234, and thorium 232. At present, we do not have good techniques for seperating out the reaction products of uranium 234 and thorium 232. However, uranium 234 is a small (.0055%) percentage of the uranium mineral and thorium 232 is usually not present in sedimentary deposits. When the uranium 235 reacts with thermal neutrons it breaks into two or more fragments and some neutrons. This occurs within a few microseconds after the primary neutrons have moderated and is the prompt reaction. One system uses this; the PFN or prompt fission neutron technique. We don&apos;t use this method because the neutron population is low and, therefore, the signal is small and difficult to work with, accurately. Within a few microseconds to several seconds the fission fragments also decay with the emmission of additional neutrons. Now, with a long time period available and a large neutron population we gate off the generator and measure the delayed fission neutrons after a waiting period. These neutrons can be a measure of the amount of uranium present around the probe. Thermal neutrons are detected with the DFN technique instead of capture gamma rays to avoid some of the returns from other elements than uranium. LOGGING TECHNIQUE The exact logging technique will depend, to some extent, upon the purpose of the measurement. However, the general technique is to first run the standard logs. These will include: 1. The gamma ray log for initial evaluation of the mineral body and for determining the position of the borehole within the mineral body, 2. The resistance or resistivity log for determining the formation quality, lithology, and porosity. 3. The S. P. curve for estimating the redox state and shale content, and measuring formation water salinity, 4. The hole deviation for locating the position, depth, and thickness of the mineral (and other formations), and 5. The neutron porosity curve. The neutron porosity curve is most important to the interpretation of the DFN readings. The neutrons from this tool are affected in the same way by bore hole and formation fluids as the DFN neutrons are. Therefore, we can use this curve to determine effect of the oxygen 17 in the water. Of course, this curve can be used to determine formation porosity. It can also be used to calculate formation density.

Jan 1, 1979

By M. H. Merriss

IN THE last few years, there have been developed at the plant of the Nichols Copper Co., Laurel Hill, Borough of Queens, New York City, improvements in electrolytic copper refining by the series system that have materially increased the flexibility and economy of that system. The purpose of this paper is to discuss, as of interest to refiners and to those who have copper to refine, as well as to the engineering profession in general, the changes that have taken place resulting in wider application and increased efficiency of the series system. Copper is electrolytically refined in two ways, which are spoken of as the "multiple system" and the "series system." In both systems, the electrolytic tanks are in series electrically. In the multiple system the electrodes in a single tank are in multiple or in parallel, thus: In the series system, the electrodes in a single tank are in series, thus: There are two important adaptations of the series process, one represented by the series electrolytic tank room at the Baltimore Copper, Smelting & Rolling Co., Baltimore, Md., and the other by that of the Nichols Copper Co.&apos;s plant. At Baltimore, the anode is rolled to perfect

Jan 6, 1925

By L. A. Schrider, J. A. Wasson

A method of predicting waterflood performance has been developed that combines certain facets of several previously published prediction techniques. The manner of combination has required the development and use of some new and some little-known relationships and has eliminated several of the weaker assumptions inherent in the original individual prediction methods. This approach, which was designed for computer solution, has removed the necessity of referring to plotted curves and permits the analytical prediction of water flood performance for a five-spot well pattern in either homogeneous or stratified reservoirs. The Predicted values are expressed in common oilfield units rather than in abstract or dimensionless terms. The calculation procedure has been programmed in FORTRAN IV and the entire program listing is available to potential users.* Introduction Prior to initiation of secondary recovery of oil by waterflooding, the possibilities of economic success or failure must be evaluated with the greatest practical accuracy. Although many prediction techniques are available, most, if not all, have serious limitations. In recent years, the Bureau of Mines has attempted to stimulate interest in the secondary recovery of oil from Appalachian pressure-depleted reservoirs. Waterflooding, because of its widespread acceptance and success, is the principal secondary-recovery method considered. During the life of the project, several performance prediction methods have been studied and applied. Because these methods, individually, have inherent assumptions and limi-tations, portions of some of them have been selected and combined in an effort to eliminate such shortcomings wherever possible. We believe that the resulting technique is as accurate as the necessary available data will permit and that it has several distinct advantages over previously published methods. Development of the Method The fractional flow equation developed by Buckley and Leverett&apos; from Darcy&apos;s law is the fundamental mathematical statement describing immiscible fluid-fluid displacement in porous media. A generalized form of this relationship, whose derivation is readily available in the literature, is The formation dip, a, is usually very small in those petroleum reservoirs being considered for pattern waterflooding in the Appalachian area. Therefore. in many cases. a has an almist negligible value. In addition, Ap, the difference between the density of water and the density of oil, is relatively small. For these reasons the gravitational term may often be neglected. Capillary pressure is a function of saturation, which is in turn a function of distance from the upstream boundary of the system or the injection well. In this study it is assumed that the frontal zone of the waterflooding (or zone of capillarity) has negligible length and that only those saturations in the water-swept zone at breakthrough and later are of interest. As the distance in a waterflood pattern is comparatively large and the change in water saturation with distance is usually small, the change in capillary pressure with distance is negligible. The simplified form of the fractional flow equation is appropriate, therefore, in this application. Three variables must be considered in determining that fraction of the total fluid flow that consists of water: the viscosity ratio, saturation, and relative permeability ratio.

Jan 1, 1969

By L. Russell, van Wert

During an investigation in which the solubility relations of the phases in Muntz metal (60 per cent. copper, 40 per cent. zinc) were under study, certain phenomena that had no immediate connection with the main problem were observed, which were thought sufficiently interesting to study further. Because of lack of time, only a preliminary survey was made of two of these; namely, the cleavage structure developed under certain conditions in a 60:40 brass and abnormal grain growth in this alloy. Cleavage Structure in Heat-treated Muntz Metal Carpenter noted many years ago that cold-working a brass of the Muntz metal type, which had been quenched previously from within the beta field, results in a partial breakdown of the supersaturated beta solution and the precipitation of the solute (the alpha solution) in the cleavage planes of the beta grains. This manner of rejection of a solute from a metastable solid solution is not peculiar to this particular alloy, for among others, it occurs in the cold-working of certain austenitic steels; for example, the austenitic nickel steels. In these ferrous alloys, cold deformation produces a partial decornposition of the austenite, with the formation of martensitic "needles" and zigzags in the austenitic poly-hedra. It is interesting to note that while the two solid solutions— austenite and quenched Muntz metal— are metastable and in their mode of decomposition behave quite alike when deformed in the cold, the metastability of each results from a different cause; viz., that of the austenite from the fact that it is a supercooled solution (its solvent. gamma iron, at ordinary temperatures is below its normal stable range whereas the metastability of the quenched Muntz metal is the result of supersaturation. When a 60:40 brass is quenched from above 800" C.—that is, from within the field where the beta phase alone is stable—this solution is retained practically intact and the alloy so cooled is found to consist almost entirely of polyhedra of this solution with only a little alpha present ordinarily at the boundaries of the beta grains—the result of a slight

Jan 1, 1929

By van Wert, L. Russell

During an investigation in which the solubility relations of the phases in Muntz metal (60 per cent. copper, 40 per cent. zinc) were under study, certain phenomena that had no immediate connection with the main problem were observed, which were thought sufficiently interesting to study further. Because of lack of time, only a preliminary survey was made of two of these; namely, the cleavage structure developed under certain conditions in a 60:40 brass and abnormal grain growth in this alloy. Cleavage Structure in Heat-treated Muntz Metal Carpenter noted many years ago that cold-working a brass of the Muntz metal type, which had been quenched previously from within the beta field, results in a partial breakdown of the supersaturated beta solution and the precipitation of the solute (the alpha solution) in the cleavage planes of the beta grains. This manner of rejection of a solute from a metastable solid solution is not peculiar to this particular alloy, for among others, it occurs in the cold-working of certain austenitic steels; for example, the austenitic nickel steels. In these ferrous alloys, cold deformation produces a partial decornposition of the austenite, with the formation of martensitic "needles" and zigzags in the austenitic poly-hedra. It is interesting to note that while the two solid solutions— austenite and quenched Muntz metal— are metastable and in their mode of decomposition behave quite alike when deformed in the cold, the metastability of each results from a different cause; viz., that of the austenite from the fact that it is a supercooled solution (its solvent. gamma iron, at ordinary temperatures is below its normal stable range whereas the metastability of the quenched Muntz metal is the result of supersaturation. When a 60:40 brass is quenched from above 800" C.—that is, from within the field where the beta phase alone is stable—this solution is retained practically intact and the alloy so cooled is found to consist almost entirely of polyhedra of this solution with only a little alpha present ordinarily at the boundaries of the beta grains—the result of a slight

Jan 1, 1929

By Arthur G. Levy, Henry M. Howe

$1. Introduction.—Any given piece of metal is made up of a very great number of grains, usually microscopic, each of which is a perfect crystal save only in outward form, with cleavage planes of low cohesion, geometrically arranged quite as in fie familiar non-metallic crystals. The plastic deformation of such a mass occurs chiefly through the slipping of the crystalline blocks of which each grain is composed along these cleavage planes, causing steps called slip bands to form on a previously polished surface. In this slip, the metal immediately adjoining each of the cleavage planes along which the slip takes place is thought to pass extremely rapidly through a very mobile state into the amorphous state, in which it is harder than the remaining still crystalline metal between the amorphous layers thus formed along the slip planes. Whether the slip planes below the surface in ferrite can be detected by cutting, polishing, and etching sections is in dispute; but if this detection is possible at all, it is usually made impossible by heating the metal even gently. In short, the change along the slip planes does not persist through heating, and it is thought not to persist through time even at the room temperature, nearly all the amorphous metal recrystallizing. The network in Fig. 22 and the parallel N.-70-E. lines in Fig. 21 are slip bands in copper. When plastically deformed metal is heated, certain parts of certain grains may twin, that is, their component crystalline units may rotate into a position, or more exactly into an orientation, symmetrical with the initial orientation and hence with that of the remainder of that grain. As seen in a microsection of a metal the twinned areas usually have parallel sides. The existence of twinning is recognized in metallic sections either by the presence of such parallel-sided areas differing in brightness from the adjoining metal, especially when seen under oblique light after etching, or more surely by the zigzagging of the slip bands which form when twinned metal is itself deformed again. Hence the usual procedure in developing twins is to deform plastically so as to cause the twinning tendency; to heat so as to allow the tendency to assert

Jan 1, 1915