Search Documents

By N. J. Grant, Per Knudsen, J. T. Blucher

The fatigue behavior of three SAP alloys was studied in ternzs of strain rate and temperature, at high strains. The k values in the modified Manson-Coffin equation, Nk4 = C, were less than 0.5 under all test conditions, and change with strain amplitude for the lower-oxide alloys at about 2 pct strain. Lowest k values were near 0.25. Strain rate had no effect on life at 80 F, but had an increasingly greater effect with increasing temperature above 500". Life decreased with decreasing strain rate, above 500"F, and with increasing temperature. Ductility at fracture in a tension test was indicated to be an important factor in determining 1ife in these big+-strain tests with the SAP alloys. INEVITABLY, in the course of mechanical tests at elevated temperatures, particularly if significant time at temperature is involved, there are large changes in structure; these changes make it difficult to relate behavior patterns over ranges of temperature or strain rates at high temperatures. Such changes are to be expetted in low cycle fatigue at low strain rates and high temperatures. Accordingly, it was of great interest to examine the low cycle fatigue behavior of SAP / an aluminum oxide dispersion-strengthened aluminum, a type of alloy which had shown unusual structure stability to temperatures as high as 1000" to 1150°F and resisted recrys-tallization essentially to the melting temperature.'j3 Since the matrix is pure aluminum, there are no complications of averaging, agglomeration, or phase solution. It was also desirable to check the Manson-Coffin equation4?' for the SAP alloys, namely N~E~ = , where ep is the total plastic strain amplitude, k and C are constants, and N is the number of cycles to failure. Here, too, was an opportunity to check the roles of temperature and strain rate with a very stable material. Tavernelli and coffin6 had concluded that k had a value of about 0.5 for many alloys and C was equal to ~/2, where E is the fracture ductility determined from a static tension test. The results were obtained from low-temperature tests where creep and diffusion processes are unimportant. Manson7 found k = 0.6 fitted his data reasonably well; however, in later analyses of a large amount of low cycle fatigue data generated at room temperat~re@"~ he found k to vary from 0.6 for short lives to 0.21 for long-life fatigue tests. In the latter studies,89g Manson separated the total strain range into elastic and plastic components when he found that k was influenced by the nature of the strain. The use of EL (total strain) instead of EP (total plastic strain)4'5 makes a difference in the resultant k value. The ratio of changes with temperature, strain rate, and strain; further, there are the problems in the determination of the elastic strain. Based on these considerations, and the improved fit of points in a plot of by Wells and Sullivan,' is also utilized in these studies. Anderson and wahl,14 using commercial 1100 aluminum, and Blucher and Grant,15 using 99.99 pct pure aluminum, found an increase in life with increasing test temperature. Anderson and Wahl were the first to report low cycle fatigue results from SAP materials. With increasing temperature, the role of strain rate becomes more important. In this regard, care must be exercised to differentiate between frequency (wherein strain rate may vary from zero to a maximum in each cycle, sinusoidally, for example), and constant strain rate, as used in the present study, in a saw-tooth type cycle; in the latter case, the frequency is not specified but can easily be calculated from the strain and strain rate data. It has generally been found that life in low cycle fatigue tests decreases with decreasing frequency16 or with decreasing strain rate at elevated temperatures.15 Coffin,17 reviewing Eckel's work,16 also reported that k increased with decreasing frequency for acid lead, yielding values from 4.0 at a frequency fo 6.6 cycles Per day to 1-46 at a frequency of 7440 cycles per day; the value of k decreased to 0.58 at a frequency of 2.38 x lo6 cycles per day. EXPERIMENTAL PROCEDURE Three SAP alloys, of two nominal compositions, were tested. Alcoa supplied XAP 005 as 2-in.-diam extruded bar, of nominal composition A1-7 wt pct A1203. The Danish Atomic Energy Commission supplied SAP 930 (A1-7 wt ~ct Ala3) and SAP 865 (A1-13 wt pct Al&) manufactured by Swiss Aluminium Ltd., in the form Of $-in.-diam extruded rod. Metallographic comparison of the structures of XAP 005 and SAP 930 showed the former to have a more uniform oxide distribution. Button-head specimens were machined in the longitudinal direction of the bar with 0.4 in. gage length by 0.2 in. diameter, with a fillet radius of j-B in. After machining, the specimens were electropolished in a 1 to 4 mixture of perchloric acid to methanol to remove all machining marks. All test bars were in the as-extruded condition. The fatigue tests were performed on a hydraulically activated, axial strain machine, with complete reversal of strain.15 Test conditions were:

Jan 1, 1969

By Y. Baskin

Solid-solubility relationships in the Pseudobinary systems UAS-UP, UAs-US. UAS-UC, aid UAs-UN were investigated. The first two systems exhibit complete mutual solubility, whereas the component compounds in the other two systenzs are immiscible. The above information, together with solid-solubility data joy six additional pseudobinary systems , were analyzed for compliance wilh the Hurrze-Rothery rules for rnetallic systems. The relative size difference of the component nonmetal atoms was found to be the dopainant jactor determining the extent of solid solubility between the NaC1-type uranium compounds. The anionic and covalent radii of the nonmetal atoms appear to be inadequate for these systems, but compuled radii based on rare earth compounds yield consistent results for the uranium compounds. THE actinide elements, like metallic elements of the transition and rare earth series, readily form binary compounds with nonmetallic elements of groups IV, V, and VI of the periodic table. Of particular importance are the NaC1-type equiatomic compounds with carbon, nitrogen, sulfur, phosphorus, and arsenic. The uranium members of this family of compounds have high melting points, are essentially stoichiometric, and exhibit various amounts of mutual solubility. Thus, they are of interest for investigating the factors governing the extent of solid solubility. Previous investigators have determined the solid-solubility limits in the pseudobinary systems between the compounds UC, UN, US, and UP. Anselin et a1 .' reported complete miscibility in the system UC-UN. Baskin and shalek 2 and Allbutt et a1.3 reported that UP and US exhibit complete mutual solubility. Shalek and white4 reported partial miscibility in the system US-UC. At 1800°C the maximum solubility of UC in US is 40 mol pct, but that of US in UC is 4 rnol pct. shalek5 found limited solubility in the system US-UN; the maximum solubility of UN in US is 11 rnol pct at 1800°C, while that of US in UN is only 0.3 mol pct. White and askin 6 found very limited miscibility in the system UP-UC at 1800°C. Approximately 7 mol pct UC is soluble in UP, but there is no solubility of UP in the monocarbide. Phase relations in the pseudo-binary system UN-UP were investigated by askin.' Approximately 0.7 mol pct UN is soluble in UP at 1800°C, while UP is immiscible in UN. The present study was carried out to explore the extent of terminal solubility in the systems UAs-UC, UAs-UN, UAs-US, and UAs-UP. This information, combined with existing data, provided a sufficient basis on which to determine the factors governing solid solubility in pseudobinary systems containing NaC1-type uranium conpounds. I) EXPERIMENTAL 1) Materials. The compounds UC and UN were obtained from the Kerr-McGee Corp. and United Nuclear Co., respectively. The US, UP, and UAs were synthesized by reacting finely divided uranium with H2 S, pH3, or AsH3 gas at low temperature (300° to 500°C), followed by homogenization in a vacuum at moderately high temperatures (1400° to 1700°c).8-10 The materials were essentially stoichiometric, with the exception of UC, which exhibited a C/U ratio of 1.05. Oxygen was the major contaminant in these compounds, ranging from 0.05 wt pct in US to 0.30 wt pct in UC, and it was generally combined with uranium to form UO2. The UO2 content in these materials was usually of the order of 1 wt pct, and did not exceed 2 wt pct. Furthermore, no evidence was found for a high-temperature reaction between uranium dioxide and any of the compounds. Chemical analyses of equilibrated compositions in the systems UAs-UP and UAs-US showed that the non-metal atom to uranium ratios averaged about 1.01, and that the oxygen contents ranged from 0.06 to 0.22 pct. However, the small deviations from stoichiome-try or the presence of minor oxygen impurities do not invalidate the conclusions to be drawn from this study. 2) Experimental Procedures. The component compounds in powdered from were blended in the desired proportions for 5 hr in the ball mill that consisted of stainless-steel balls in a plastic container. Chemical analyses indicated very little metallic pickup from the blending operation and virtually no increase in oxygen content. The pellets were pressed in a 0.270-in.-diam steel die under 40,000 psi pressure. One wt pct of stearic acid dissolved in CCl 4 served both as a binder and as a die lubricant. Chemical analyses revealed that the stearic acid left no carbon residue in the sintered samples. The pellets were sintered in vacuum in an unsealed tantalum crucible. The temperature, measured with a calibrated optical pyrometer, was maintained at 1800" + 30°C for 3 hr. This was sufficient time for attaining equilibrium as no change occurred in either the lattice parameters or the sharpness of the X-ray patterns when samples were annealed for longer periods of time. The pellets were cooled with the furnace. Debye-Scherrer powder patterns were taken at room temperature with a 114.59-mm-diam Norelco powder camera and CuKor radiation (CuGI = 1.5405A). Unit cell dimensions were determined from a Nelson-Riley extrapolation to the high-angle reflections. The values for were precise to k 0.001A. 11) RESULTS X-ray and met allographic investigation revealed that complete mutual solid solubility exists in the pseudobinary systems UAs-UP and UAs-US. The lattice parameter vs composition plots, Fig. 1, show a

Jan 1, 1968

By Carl J. McHargue

Mechanical twins were produced in electron-beam melted columbium by high-speed impact at room temperature and by slow or fast compression at -196°C. The composition plane of the twins was { 112} and the shear direction was <111>. Notches in the twin bands often corresponded to traces of {110) of the matrix and appeared to be untwinned regions. Markings within the twin bands were interpreted as resulting from {110} slip in the twins. THERE has been much work in recent years concerning plastic deformation by glide, and the dislocation theory relating to glide has reached a relatively high degree of development. On the other hand, there have been fewer studies of deformation by mechanical twinning, and understanding of this process is far from satisfactory. This method of deformation is of interest for at least two reasons. First, it provides a mechanism in addition to glide for the relief of stresses, and, in the bcc and hexagonal close-packed metals may result in significant amounts of plastic flow. Secondly, there is the possibility that twins may act as barriers for dislocation movement, resulting in pile-ups which could nucleate cracks. As might be expected, the bulk of the literature on mechanical twinning in the bcc metals is concerned with iron. A good summary of the work done prior to 1954 is contained in the book by all.&apos; Recently the refractory bcc metals have become increasingly important. Limited studies have shown that tantalum,2,3 molybdenum,4,5 vanadium,6,7 tungsten,&apos; and columbium9-11 deform by mechanical twinning under some conditions. Alloys of molybdenum with rhenium and tungsten with rhenium show extensive deformation by twinning at room temperature.I2-l4 Most of these studies have dealt primarily with mechanical properties at low temperatures or have shown the existence of twins, and there is only a small amount of information concerning the conditions under which they form. The subject of the present paper is the formation of twins under stress in columbium with a consideration of their morphology. EXPERIMENTAL PROCEDURE The material used for these studies was taken from an ingot of columbium which had been melted twice by the electron-be am-method. The analysis of the ingot was (in ppm): B < 1, C = 10, Fe < 100, The cast ingot contained very large grains, and it was possible to obtain single-crystal prisms which measured from ¼ to 3/4 in. on a side. A few experiments were conducted on polycrystalline plate which was prepared by rolling material from the same ingot at room temperature and annealing at 1000 in a dynamic vacuum of 10-6 mm Hg. This gave a plate in which the grains had an average diameter of 3 mm. After the specimens were cut from the ingot, the six faces were metallographically polished and elec-tropolished to remove all traces of cold work. Most of the observations were made on the surfaces of the deformed specirllens without further treatment. Occasionally, etching after deformation was desirable. In these cases, an etchant of the composition 50 parts H2O, 5 parts HNO3 25 parts HF, and 10 parts H2SO4 was found to delineate the twins very well. Unless considerable care was taken to ensure the removal of all disturbed metal left by the mechanical polishing, etching failed to reveal many of the features discussed in this; paper. The specimen&apos;s were deformed either by impact or slow compression at 77°K (liquid-nitrogen coolant), 198°K (dry ice and acetone coolant), and 298°K. The impact load was delivered by a hammer except in one case where the load was delivered by a bullet. Slow compression was carried out on a hydraulic testing machine equipped with a chamber to hold the coolant. EXPERIMENTAL RESULTS It has been generally believed that the conditions favoring the formation of deformation twins are large grains, low temperature, and impact loading. In fact, Barrett and Bakish2 found twins in tantalum only after impact deformation at 77°K, and Adams, Roberts, and Smallman10 observed twins in columbium only at 20 For these reasons, the initial experiments of this study used impact loading. Hammer blows caused many bands resembling twins in single crystals a.t 77" but not at 198°K. Only a few slip lines were observed on any of the single-crystal specimens of this study—essentially all the deformation occurred by twinning. The appearance of the twins on the as-deformed surface is shown in Fig. 1. Although both Figs. 1(a) and l(b) are photomicrographs of twins taken at the same magnification and from the same crystal, they are startlingly different in appearance. Fig. 1(a) was taken from the crystal face approximately perpendicular to the shear direction, whereas Fig. 1(b) was taken from

Jan 1, 1962

By T. E. Leontis, F. N. Rhines

THE oxide scale that forms upon magnesium at elevated temperatures is nonprotective in the sense that the rate of oxidation is constant and thus does not decrease with the growth of the scale as it does with other common metals. This generality was first stated by Pilling and Bedworth1 and has been verified by Suzuki2 and by Scheil.3 Pilling and Bedworth argued that the nonprotective characteristic could be predicted from the fact that magnesium oxide occupies less space than does the metal from which it springs, wherefore the scale is not expected to cover the metal so completely as to exclude all direct access to the atmosphere. Linear oxidation is thought by Scheil to be common to all cases where the reaction occurs at the oxide-metal interface. According to Suzuki,2 the product of high-temperature oxidation in the air is MgO contaminated with no more than traces of a nitride. When the metal is allowed to burn freely a fume composed of cubic crystals of Mg04 is given off. Delavault5 observed that excrescences form upon liquid magnesium and alloys in the course of oxidation. Beyond this it is known that the use of atmospheres containing small quantities of sulphur dioxide6 or carbon dioxide serve to retard the oxidation of solid magnesium and that beryllium7and calcium8 minimize the oxidation of molten magnesium exposed to the air. Many studies have been devoted to the nature and rates of "protective" oxidation, as exemplified by the cases of copper and iron, wherein the rate is characteristically parabolic. The theory of parabolic oxidation is well developed.9 Linear oxidation, on the other hand, has received but little attention and the theories proposed by Pilling and Bedworth and by Scheil have yet to withstand careful examination. There exists no comprehensive survey of the high-temperature oxidation of magnesium (or of any other metal that exhibits linear oxidation) over a broad range of temperature, under a variety of atmospheric conditions and covering a large group of alloys. It has been the purpose of the present investigation to provide such a survey, with the object of gaining a fuller understanding of linear oxidation, especially as applied to magnesium. EXPERIMENTAL PROCEDURE AND RESULTS The experimental studies undertaken were of two kinds: (I) measurement of the rate of oxidation as influenced by the

Jan 1, 1946

By J. O. Betterton, W. M. Spicer

The solubilities of antimony in the a and ß-forms of zirconium were determined between 750" and 1300°C. The a-phase forms by a peritectoid reaction, and the a/(a + ß) and ß/(a + ß) phase boundaries rise in temperature with in- &apos; creasing antimony. Impurities in the 99.95 pct zirconium were sufficient to influence the phase boundaries and the variation reported is approximate. The restricted solid solubility of the terminal zirconium phases, which is especially characteristic of this system, is thought to result from the low free energy of the Zr2Sb phase. ZIRCONIUM-antimony alloys are important in zirconium alloying studies since antimony is one of the highest valent elements which can be used to make zirconium alloys. The dilute alloys are of further interest as they have somewhat better corrosion resistance&apos; than pure zirconium. The first investigation of the phase diagram was made by Russi and wilhelm2 who found a eutectic reaction, liquid (- 17.5 at. pct Sb) = ß zirconium (- 11 at. pct Sb) + Zr2Sb, at 1430°C&apos;. The Zr2Sb phase was of complicated hexagonal structure, and by thermal analyses of the relatively impure alloys then available, Russi and Wilhelm found evidence for the peritectoid formation of the a-phase. EXPERIMENTAL In the present work, the phase diagram was re-investigated in the region 0 to 5 at. pct Sb and 750" to 1300°C using iodide-zirconium alloys. Details of the procedure have been described earlier. Essentially the alloys were prepared by arc casting and were then examined by the annealing and quenching method. The times of annealing varied from 1 hr at 1300°C to 30 days at 760°C. As in other zirconium phase-diagram studies1"5 the impurities in the zirconium were still sufficient to affect the results, and the experiments will therefore be described in 3 parts. The results from the first 2 parts of the work are shown in Fig. 1. Here the ß/(ß + Zr2Sb) and a/(a + ZrzSb) phase boundaries were determined with alloys made from 99.9 pct zirconium,* and cast under such conditions that the Vickers hardness of a alloys extrapolated to 95 to 110 VPN at 0 at. pct Sb. Such alloys were not suitable for investigations of the (a + ß) region, and the results shown in Fig. 1 near the (a+ ß) and (a +ß + Zr2Sb) regions were determined with purer alloys. These alloys had an extrapolated hardness range of 75 to 85 VPN and were made from 99.95 pct zirconium. A deviation from binary equilibrium occurs in Fig. 1 as indicated by the (a + ß) region of pure

Jan 1, 1959

By H. D. Hoskold

DuRing the last few years, various persons have been put forward as originators of some mechanical device for the purpose of finding distances without the use of a chain or other linear measuring-instrument, and among these, the Englishman, Gascoigne, 1639, is prominent as the first in England; while James Watt, 1771, and William Green, 1778, are also included in the list of inventors. It is possible that this useful and important problem occupied the attention of others prior to the date cited, and, consequently, it is difficult to decide what nation first gave birth to the inventor of an instrument for the object under consideration. A very important work appeared, not long since, in Paris, devoted to a history and discussion of some of the older and newest forms of surveying-instruments,* and at page 79 of that work a curious old instrument is exhibited, called Bigonometre, i. e., an instrument for finding distances and solving trigonometrical problems. in surveying. A copy of the diagram of the instrument exhibited in the book referred to is represented in Fig. 1. Having had an occasion to read the French work referred to, I communicated with the author of it, and he was good enough to reply that he found a diagram of this old instrument in a book published in 1597, by Danfrie, existing in the library of the Academy of Sciences, in Paris. Col. Laus-

Jan 1, 1904

By A. R. Gregory

A shear wave velocity laboratory apparatus and techniques for testing rock samples under simulated subsurface conditions have been developed. In the apparatus, two electromechanical transducers operating in the frequency range 0.5 to 5.0 megahertz (MHz: megacycles per second) are mounted in contact with each end of the sample. Liquid-solid interfaces of Drakeol-aluminum are used as mode converters. In the generator transducer, there is total mode conversion from P-wave energy to plain S-wave energy. S-wave energy is converted back to P-wave energy in the motor transducer. Similar transducers without mode converters are used to measure P-wave velocities. The apparatus is designed for testing rock samples under axial or uniform loading in the pressure range 0 to 12,000 psi. The transducers have certain advantages over those used by King, 1 and the measurement techniques are influenced less by subjective elements than other methods previously reported. An electronic counter-timer having a resolution of 10 nanoseconds measures the transit time of ultrasonic pulses through the sample; elastic wave velocities of most homogeneous materials can be measured with errors of less than 1 percent. 5- and P-wave velocity measurements on Bandera sandstone and Solenholen limestone are reported for the axial pressure range 0 to 6,000 psi and for the uniform pressure range 0 to 10,000 psi. The influence of liquid pore saturants on P- and S-wave velocity is investigated and found to be in broad agreement with Biot&apos;s theory. In specific areas, the measurements do not conform to theory. Velocities of samples measured under axial and uniform loading are compared and, in general, velocities measured under uniform stress are higher than those measured under axial stress. Liquid pore fluids cause increases in Poisson&apos;s ratio and the bulk modulus but reduce the rigidity modulus, Young&apos;s modulus and the bulk compressibility. INTRODUCTION Ultrasonic pulse methods for measuring the shear wave velocity of rock samples in the laboratory have been gradually improved during the last few years. Early experimental pulse techniques reported by Hughes et al.2 and by Gregory 3 were beset by uncertainties in determining the first arrival of the shear wave (S-wave) energy. Much of this ambiguity was caused by the multiple modes propagated by piezoelectric crystals and by boundary conversions in the rock specimens. Shear wave velocity data obtained from the critical angle method, described by Schneider and Burton4 and used later by King and Fate sand by Gregory, 3,6 are of limited accuracy, and interpreting results is too complicated for routine laboratory work. The mode conversion method described by Jamieson and Hoskins7 was recently used by King 1 for measuring the S-wave velocities of dry and liquid-saturated rock samples. Glass-air interfaces acted as mode converters in the apparatus, and much of the compressional (P-wave) energy apparently was eliminated from the desired pure shear mode. A more detailed discussion of the current status of laboratory pulse methods applied to geological specimens is given in a review by Simmons.8 A new shear wave velocity laboratory apparatus has been developed for testing rock samples under elevated pressures. This apparatus employs liquid-solid interfaces as mode converters. The technique for generating pure shear waves at liquid-solid interfaces was developed from studies of critical angle methods.6 Two identical transducers are placed in contact with opposite ends of the rock sample, one transducer acting as an ultrasonic energy emitter or generator and the other acting as an ultrasonic energy receiver or motor. The P-wave energy emitted from the piezoelectric crystal in the generator transducer is converted into pure S-wave energy at the Drakeol-aluminum

By Paul B. Crawford, Bobby L. Landrum

Electrical model studies have been made of the effect of drainhole drilling on production capacity. Drain holes are those lateral holes which are sometimes drilled to assist in increasing the oil drainage into the main wellbore. The studies indicate that if the drainhole length i.r near 0.2 of the drainage radius, the increase in production capacity may be approximately 1.8, 2.08, trnd 2.33 for the case of one, two and four drain holes, respectively. If multiple drain holes are drilled, shorter holes are required to achieve a specific increase in production capacity than if one or two holes are drilled. To achieve increases in production capacities by factors near three it is shown that the drainhole lengths divided by the drainage radii must be approximately 0.64, 0.48, cnd 0.37 for the case of one, two and four drain holes, respectively. IN T RO DUCTION Kecent developments in drilling techniques have permitted the drilling of lateral or horizontal holes to increase the rate of production. The number of these drain holes may vary from 1 to 10, and they have been drilled laterally as much as 100 ft. Drainhole drilling at substantial depths is of recent origin but has been used in the Spraberry field of West Texas, the La Pas field in Western Venezuela, and certain fields in California. The diameter of the drain holes has been approximately 6 in. In drilling drain holes it is desired to know how much increase in production capacity may be expected, what additional benefit may be gained by drilling more than one drain hole, and what increase in production capacity may be brought about by lengthening the existing drain holes. In realization of the importance of lateral drilling, electrical model studies were made to provide quantitative estimates on the effect of drain holes on production capacity. ANALYSIS An electrical model was used in studying this problem. A wooden circular reservoir approximately 30 in. in diameter and 2 in. deep was filled with a dilute salt solution to a depth of 1 in. A copper band formed the periphery of the tank, and a copper wire was inserted in the center of the tank to represent the well. The drainage radius divided by the well radius was equal to 500. A diagram of this type model is shown in the inset of Fig. 1. An electrical potential was applied to the wire well and copper band at the periphery to determine the flow of current. Following this measurement copper wires of various length were soldered to the vertical wire well in such a manner as to simulate lateral wells drilled into the reservoir. Multiple lateral holes of various lengths were studied by varying the number and length of copper wires soldered to the vertical wire well. All multiple lateral wells were located symmetrically about the vertical well. The effect on production capacity by drilling an infinite number of lateral holes was studied by replacing the lateral hole with a copper disk. For each condition the flow of current was measured and compared with the flow of the vertical well only. The model which is thus described provides the steady state increases in production capacity which may be expected in some cases. The data conform to those which would be observed for a uniform homogeneous reservoir. The data may have primary application to those reservoirs producing above the bubble point. It is realized that few lateral holes are drilled in reservoirs of this type, but the data may be of some value in guiding future work or aiding to explain observed phenomena.

Jan 1, 1956

By R. T. DeHoff, F. N. Rhines

The problem of determining the number of particles of a phase distributed randomly in unit volume c an opaque matrix from measurements made on random plane sections is closely investigated. A formalized derivation for the general case is presented. Applications of this formal result are made to specific types of aggregates dispersed in a matrix; circles, particles with flat circular ends, cylinders, and constant shape aggregates of ellipsoids of revolution. Quantitative measurements of the average geometric properties of these aggregates are developed. In 1953 R L. ullman&apos; developed a technique for determining, from measurements made on random plane sections, the number per unit volume, Nv, of particles imbedded in an opaque matrix. Using meas urements previously developed for volume fraction, vV,&apos; and surface area per unit volume, .SV,= he was able to determine average volume, average surface area, and average dimensions of particles, independent of size distribution, for spheres and circular disks,&apos; as well as for uniformly sized cylinders of any axial ratio.4 The technique is mathematically rigorous for the cases studied. Recent studies of this problem have yielded rigorous solutions for the general case of cylinders, permitting evaluation of NV independent of size distribution and with all axial ratios intermixed. Generalization to shapes having flat, circular ends has been deduced. A solution has also been obtained for the ellipsoid of revolution, independent of size distribution, but requiring a constant axial ratio in the generating ellipses. In the following derivations, as in Fullman&apos;s work, it is assumed that the problem is purely a combination of geometry and probability theory,that is,eithe the particles to be measured are imbedded randomly in the matrix, or a sufficient number of random plane sections are taken to make the sample representative. A relationship exists between the number of par- ticles of a given size and shape that may be situated in unit volume (Ny) and the number of intersections a random plane can be expected to make with these particles (Na). It is the purpose of the following section to derive this relationship. The probability of Intersecting Convex Bodies. Consider a convex, closed surface, that is, one for which no two surface normals point in the same direction, situated at some arbitrary position and orientation in a cube of material that is one unit long at each edge. It is not necessary to assume that this surface is symmetrical. Let planes be constructed in the cube parallel to the top face and at random distances from it. Those planes which lie between the two planes which are just tangent to the top and bottom of the surface will intersect it. The probability that a plane will intersect the body may be defined as the limit of the fraction of planes that lie between the two tangent planes as the total number of planes constructed becomes infinite. This fraction, in the limit, is equal to the distance between the two tangent planes, DV, divided by the total length over which planes are constructed, which has been taken as unity. If the body is now rotated to a new orientation, applying the same argument, the probability of intersection is again numerically equal to the distance between tangent planes. Let DV ($, 0) be defined as the distance between tangent planes of a convex body as a function of orientation, Fig. 1. The probability, Pr, of intersecting the body with a randomly oriented and randomly positioned plane, is then equal to the average value of DV (0, $) over all possible orientations. It may be easily shown that for a system of spherical coordinates the probability of finding an orientation between Q and Q + de, $ and $ + d$ is (1/4n) sin $ dB d$, so that This relationship may be applied to each body in an aggregate of convex bodies. In particular, if the bodies in an aggregate are classified according to size and shape, and the ithsuch class is considered, Eq. 111 may be applied to this entire class, the probability of intersecting any body in this class being

Jan 1, 1962

By R. H. Kolb

A long term project at Shell Development Co.&apos;s Exploration and Production Research Laboratory has been the improvement of the accuracy and the ease of BHP measurements. As a result of these efforts, two complete and separate systems have now been built for the automatic logging of BHP variations. The first of these is a small-diameter instrument suitable for running through production tubing on a single-conductor well cable. During the development of this instrument, as much emphasis was placed on providing a high degree of usable sensitivity and repeatable accuracy as on obtaining the advantages of surface recording. The second system combines the benefits of automatic, unattended recording with the convenience of a permanently installed Maihak BHP transmitter.&apos; THE CABLE INSTRUMENT For many years the standard instrument for BHP determination has been the wireline-operated Amerada recording pressure gauge or one of several other similar devices. This gauge records on a small clock-driven chart carried within the instrument, and although relatively precise readings from the chart are possible, they are difficult to ob-tain. a Both the maximum recording time and the resolution of the time measurements are limited by chart size, and when a slow clock is required for long tests, the precision of the time measurement is often inadequate. Since it is impossible to determine the data being recorded until the gauge has been returned to the surface, wasted time often results when a test is protracted beyond the necessary time or when it is terminated too soon and must be re-run. Clock stoppage or other malfunctions which would be immediately apparent with surface recording remains undetected with down-hole recording; the test is continued for its full term with a consequent loss in production time. As new uses for subsurface pressure data evolved, the shortcomings of the wireline instrument became increasingly apparent, and the concurrent development of a surface-recording pressure gauge and the associated high-pressure well cable service unit&apos; was undertaken. Description of the Instrument Because of its ready availability and advanced degree of development, the Amerada bourdon-tube element was chosen as the basic pressure-sensing device. This element converts a given pressure into a proportional angular displacement of its output shaft, and a suitable telemetering system was designed to measure accurately the extent of this displacement and to transmit the measurement to the surface and record it. The telemetering system furnishes a digital record printed on paper tape by an adding machine-type printer. The present arrangement provides a resolution of one part in 42,000 over the angular equivalent of full-scale deflection, giving a usable sensitivity of better than 0.0025 per cent of full scale. An additional refinement simultaneously records on the tape the time or the depth of the measurement, also in digital form. When the instrument is placed in operation, an adjustable programer can be set to initiate a read-out cycle automatically at selected time intervals. When subsurface pressures are changing rapidly, readings may be recorded as frequently as once every 10 seconds; when pressures are more nearly stabilized, the period between readings may be extended to as much as 30 minutes. Because the instrument is surface-powered as well as surface-recording, the maximum period of continuous logging is (for all prac. tical purposes) unlimited. The subsurface instrument is a tubular tool, 1 1/4-in. in diameter and 6.5 ft in length, operating on 12,000 ft of conventional 3/16-in. IHO logging cable. The transmitting section, mounted above the bourdon-tube element in place of the regular recording mechanism, contains no fragile vacuum tubes or temperature-sensitive transistors. This unit has been laboratory-tested to 1 0,000 psi and 300°F and has performed dependably during a number of field operations. The down-hole transmitting arrangement can be fitted to any standard Amerada pressure element, regardless of range and with no modification of the element itself. Calibration To obtain a repeatability commensurate with the sensitivity and resolution of the instrument, it was necessary to develop a special calibrating technique. The manufacturers of the Amerada recording pressure gauge claim an accuracy of only 0.25 per cent of full scale, which is a realistic figure for normal calibrating and operating procedures. An exhaustive investigation was made of the errors inherent in the bourdon-tube element, itself, independent

By Edward F. Winter, C. E. Ruoff

A silicon solid-state array image scanner is described. This paper deals with structural and performance properties of the array which basically consists of PIN photo and gating diodes, and low capacitance isolation diodes. Each chip of the array is composed of an 8 by 9 matrix of photo detector cells; each cell contains one each of the three diode types mentioned. This x-y matrix is read a column at a time with an access delay of approximately 100 nsec per column. It is designed to detect the presence or absence of illumination within 10-mil diam image spots located on a 15- by 15-mil grid. Radiant power level of an illuminated spot is low; of interest is the range around I uw with a of 8400g Structural improvements to the original array which will result THE purpose of this paper is to describe the results of a solid state scanner exploratory development activity. The scanner is intended to sense the presence or absence of low-level illumination falling upon a matrix of 10-mil wide squares arranged on a 15- by 15-mil x-y grid pattern. The light of interest has a wavelength of 8400, characteristic of radiation emitted from a GaAs lasing diode. This wavelength matches well the spectral absorption of silicon,&apos; thus the well-developed silicon processing technology can be applied to fabricating large integrated arrays of PIN photocells to sense the radiation. The illumination state of the cells of the array is read, one column at a time, by addressing a drive line of the particular column in question and examining the state of those sense lines which are orthogonal to the drive Lines of in greater sensitivity at various wavelengths, both above and below 8400Å, and in greater speed are presented. These include variations in diffusion depth, resistivity of N and P regions, isolation techniques, and packaging. Trade-offs between access speed, cycle frequency, and sensitivity are discussed. A packaging approach to achieving an array composed of several chips is described. Requirements on this package are: 1) maintenance of 15- by 15-mil pitch of the light sensitive cell position, therefore positional accuracy of mounted 8 by 9 cell photo detector chips; 2) maintenance of inherent high array speed even though signal levels are low through high density close proximity mounting of monolithic sense amplifier circuitry. the array. One bank of N sense amplifiers is required, where N is the number of photodiode cells in each column of the array. CELL AND CHI" STRUCTURE A photograph of a single monolithic cell is shown in Fig. 1. Each cell is composed of three junctions, an isolation junction, a logic or blocking diode junction, and a photodiode junction; all of these junctions are connected electrically by a common N region. An electrical schematic of four cells of the array is shown in Fig. 2 with the associated driver and sense amplifier circuits in block diagram form. Note the common cathode configuration of the three diodes of each cell. Fig. 3, a diagram of the cell vertical struc ture, illustrates how the electrical configuration of

Jan 1, 1970

By J. Chipman, T. P. Floridis

The equilibrium of gaseous H2O-H2, mixtures with liquid iron is used to establish the activity coefficient of dissolved oxygen as log f o = — 0.20 [%O]. Discrepancies in earlier work are explained or eliminated. Additions of cobalt, molybdenum, tungsten, and platinum increase the activity coefficient of oxygen whereas copper and gold decrease it. THE importance of dissolved oxygen as a refining agent in liquid steel has led to a number of studies of its thermodynamic properties. It is the purpose of this paper to examine the effects of a number of alloying elements on the activity of oxygen in the steel bath. As a preliminary to the study of the effects of alloying elements, it seemed desirable to examine certain minor discrepancies in the published data on the properties of oxygen in simple iron-oxygen solutions. The activity and free energy of oxygen in liquid iron were studied by chipman1 in 1933 by means of the reaction h2(g)+-o = H2O (g);K; = PH2O/PH2[% O] [1] The data were in fairly good agreement with calculations from results on the similar reaction CO (g) + O- = CO2 (g); K2 =P CO2/P CO [% O] [2] which had been obtained by Vacher and Hamilton2 as an incidental part of their study of the reaction of carbon with oxygen dissolved in the melt. It was found that the equilibrium ratio k1 was not a true constant but varied with the oxygen concentration in the manner shown in Fig. 1, which is copied from the original paper. This early observation has been refuted in subsequent work but is confirmed in the present paper, and an explanation of the discrepancy can now be presented. In Fig. 1, the two points on the extreme right were disregarded in drawing the

Jan 1, 1959

By M. R. Lorenz

Efficient visible light emission from p-n junctions in semiconductors is currently achieved in the four materials, Sic, GaP, ]Ga1-xAs and GaAs1-x,. Recent advances in materials preparation and p-n junction formation are briefly reviewed. The radiative recombination processes in the different materials depend largely on the band structure and the impurity states of each material. The spectral distribution of the emission ranges from the blue in Sic, to green in Gap, yellow in Sic and red in Gap, Ga1-x AlxAs and GaAs1-x Px. The origin of the various processes are discussed. The conversion of the electrical power into optical power and the measurement of the conversion efficiency are reviewed. The currently maximum quantum efficiencies at 300°K are: 3 pct in GaP(red), 1 pct in SiC(yellow), 0.1 pct in GaP(green), 0.2 pct in Ga1-x AlxAs at 66001, and 0.1 pct in GaAs1-x Px at 6800. The brightness and the interplay of the quantum efficiency and the luminous efficiency are given detailed consideration. VISIBLE light generated by the application of a direct current to a semiconductor crystal was first observed by Lossev1 in 1923. Light emission came from naturally occurring junctions in Sic crystals but little was known then with regard to the mechanism of charge transport and light emission. Some nearly 30 years later and with a vastly increased understanding of semiconductors the phenomenon of electroluminescence was studied in more detail, for example in p-n junctions of germanium.2 In these early studies, the efficiency of converting the electron current into a photon current was very low and therefore aroused little interest toward practical application. More recently it became apparent that in certain materials, for instance GaAs, and under certain conditions, the conversion efficiency was not low at all.3 The subsequent discovery of the p-n junction laser4-6 provided the impetus for increased studies of electroluminescence. Light emitted from GaAs occurs in the infrared region of the electromagnetic spectrum and is not visible to the eye. At nearly the same time the use of GaAs1-xPx led to laser action at low temperatures which was visible to the eye.7 Later a red light emitting diode, made from Gap, was reportedS which emitted incoherent radiation at 300°K with an external quantum efficiency of about 1.5 pct. The fact that such efficient devices were obtainable led to a more concentrated effort in the search for highly efficient room-temperature semiconductor light sources. It is some of this later work on p-n junction luminescence with which we will be concerned here. Since our aim is centered on visible light, with hv =1.8 ev ( ?=7000?), only the wider band gap semiconductors are of interest, i.e., Eg 1 1.8 ev. Although many compounds meet this criterion, only a limited number of those are also good semiconductors, i.e. contain low resistance n and p regions. Some of the more promising candidates are listed in Table I. We will only be concerned with light generation from a p-n junction. This limitation excludes essentially the group II-VI binary compounds, although we will briefly review the case of ZnTe and the solid solution ZnTe1-xSex. As we will show they may contain a p-n junction but only of a special kind. Most of the discussion will deal with the four materials, Sic, Gap, Gal-xAlxAs, and GaAs1-xPx. These appear to be at the present time the best visible light emitting semiconductors. In the following sections we will briefly consider: 1) the electrical properties of p-n junctions; 2) some recent advances in materials preparation; 3) the formation of p-n junctions; and then in somewhat greater detail we will consider: 4) the various radiative recombination processes; 5) the measurement and observation of the external quantum efficiency; 6) the luminous efficiency; 7) the brightness of light emitting diodes (LED&apos;S). THE P-N JUNCTION The p-n junction in a semiconductor crystal is the interface between two differently doped regions. More specifically the p region is doped predominantly with acceptor impurities and the n region contains predominantly donor impurities. The energy band structure of a degenerate p-n junction at thermal equilibrium is shown in Fig. l(a). The excess electrons on the n side of the junction are confined to this region by the barrier potential Eg. Similarly the excess holes on the p-side of the junction are confined to the p-region by a similar potential barrier. If we now apply a dc voltage V such that the p region is made positive and the n region negative, the barrier potential EB is reduced by the applied voltage, V and the junction is said to be forward biased. With the barrier potential lowered, electrons and holes can drift toward the p region and n region, respectively, see Fig. l(b). The current voltage characteristics of p-n junctions in most wide band gap materials can be described by the relation: J = Joexp(eV/BkT) [1] where the functional form of Jo is determined by the recombination mechanism. Jo is generally a complicated parameter which depends on a number of different factors including temperature, junction width, bias voltage, and carrier lifetimes. The parameter B also depends on the recombination mechanism but

Jan 1, 1970

By D. R. Irving

Prior to this time, ample supplies of high grade mineral fillers, such as clay, have been available close to consuming centers. Now depletion of these accessible deposits, coupled with other factors such as increasing demand due to population expansion and standard of living rise, has made development of upgrading techniques attractive to producers. Various investigations being carried out by the U.S. Bureau of Mines are described. Factors making the development of improved methods for upgrading clays attractive to producers include: depletion of accessible deposits of high-grade clays, rising transportation and labor costs, more exacting specifications, and increased demand resulting from an expanding population and a constantly rising standard of living. Industry recognizes the need for upgrading presently unusable materials and has cooperated with the U.S. Bureau of Mines by providing samples from submarginal deposits and by evaluating the products that USBM upgrades. Following are some examples of recent clay beneficiation work by the Bureau. FIRE CLAY BENEFICIATION At the Rolla Metallurgical Center, Rolla, Mo., the Bureau is conducting research to develop technically and economically feasible mineral-dressing methods to remove quartz, pyrite, and other impurities from submarginal fire clays. The research has been spurred by the growing shortage of high-grade bur-ley, flint, and plastic clays in the Missouri fire-clay district resulting from increased consumption and the low rate of discovery of new deposits of adequate quality. There apparently is ample tonnage of submarginal flint and plastic clays to maintain the industry for many years if such material can be upgraded to commercial quality. Samples have been submitted to USBM by several major producers of refractories, including A. P. Green Fire Brick Co.; Harbison-Walker Refractories Co.; Mexico Refractories Div., Kaiser Aluminum and Chemical Corp.; and Wellsville Fire Brick Co. Research on some samples has been completed and still is in progress on others. The Bureau has found that specimens containing quartz or pyrite in grains coarser than the accompanying clay generally can be upgraded either with a gravity table or hydraulic cyclone. The improvement in quality is notable not only in chemical analysis but in an increase in pyrometric cone equivalent (PCE) of one or more cones. As an example, consider the results attained on a sandy flint—a fine-grained mixture of kaolin and halloysite with quartz and minor quantities of iron and manganese oxides. Chemical analysis was: 35.4 pct alumina (A12O3) and 47.8 pct silica (SiO2). The sample contained 9.2 pct free silica as quartz. The PCE was 33. The sample was crushed to -10-mesh, blunged with water, and then stage-ground to -48-mesh. The ground sample was tabled to yield a clay fraction containing 37.6 pct A12O3, and 45.3 pct SiO2 of which 2.4 pct was free silica. The PCE was 34. Recovery of alumina by this process was 73.6 pct. Concentration of the same clay in the hydraulic cyclone was even more effective in respect to quartz removal. The clay fraction analyzed 38.6 pct A12O3, 45.0 pct SiO2 of which 0.5 pct was free silica as quartz, and had a PCE of 34. Recovery of alumina was 71.9 pct. The hydraulic cyclone was also effective in reducing the pyrite content of a plastic clay which likewise was a mixture of kaolin and halloysite, plus some pyrite, quartz, and carbonaceous material. It analyzed 30.6 pct Al2O3, 52.3 pct SiO2, 2.3 pct Fe2O3, and 0.76 pct S. The sample was blunged and screened through 10-mesh to remove some coarse pyrite, then ground to -65-mesh and cycloned to remove most of the remainder. The final product recovered 81.8 pct of the alumina at a grade of 32.3 pct A12O3, 50.9 pct SiO2, 1.4 pct Fe2O3, and 0.1 pct S. The PCE was 32-1/2, compared with a PCE of 31-1/2 for the crude clay. The fine beneficiated clays, of course, must be pelletized and dried or fired to meet commercial acceptance. This operation has already been solved by industry. Little progress has been made on two remaining problems. One is that of fine-grained impurities, not separable by table or cyclone. Flotation is being investigated to solve this. Although fine pyrite is readily rejected, a satisfactory quartz-clay separation has not been attained. The second problem, a stubborn one, is that of alkali. Samples containing as much as 5 pct potas-

Jan 1, 1961

R. F. McELVENNY.- Mr. Oldright has just given me a letter to read to you, which I think it may be of interest. It is headed, "Silver Meeting Dinner". The letter is as follows: "To Members of the A. I. M. & M E.: The annual business meeting and election of officers will take place at the University Club, Wednesday, May 28th, 1930 at 7 p.m., at the Silver Meeting Dinner. The Nominating. Committee for next year&apos;s officers have proposed the following names: Chairman, Robert Wallace; Vice-Chairman, G. W. Crane; secretary, C. T. Van Winkle, Other nominations can be made at the meeting. Utah being the leading silver producer of the United States, constructive suggestions regarding the silver situation will be made at this meeting which are new and of general interest to the members. The speak¬ers will be followed by a Round Table discussion of the silver situation and proposed remedies. Speakers will be - W. M. Ferry, President of the Silver Producers&apos; Association, &apos;Recent developments in the Silver Question&apos;.. Senator Frank J. Cannon, &apos;The Cannon Plan&apos;. George W. Snyder, &apos;The Manufacture of Sterling Silver.&apos; Discussion by J. J. Beason, G. W. Crane, J. 0. Elton, J. W. Wade and others. Members of the Conference on Copper Reverberatory Smelting are invited to be present. Chairman J. A. Norden will preside. C. T. Van Winkle, Secretary. Dinner will be $1.50 per plate." The next subject is "Boilers: Proper construction of, so as to secure best utilization of heat from gases, and facility in removing dust and clinker with minimum losses in operation." Who is particularly interested in that subject? The type of boilers is practically a standard practice now. I do not know of anybody that is using the tandem system now. No one is building a plant with a tandem system in it.

Jan 1, 1930

By J. J. Pfeiffer, A. A. Oming, J. W. Myers

The method used to process washery refuse for use as a building material aggregate is described. Results of studies made in investigating this process are summarized. The Bureau of Mines, in cooperation with two commercial coal producers, studied the feasibility of using coal washery refuse in manufacturing lightweight aggregate for building materials. Lightweight aggregate is used in making masonry products of lower bulk density than can be produced from conventional aggregate such as sand, gravel, and crushed rock. Among the advantages of lightweight masonry are reduced deadweight loads which reduce materials cost, lower cost of construction labor, and improved thermal and sound insulation. A process for making lightweight concrete aggregate from coal-washery refuse appeared attractive because of the availability of raw material which contained sufficient fuel to carry out the processing. Vast quantities of such refuse have accumulated throughout the coal-producing areas of the U.S. Generally it is stored in unsightly piles, creating a problem of air pollution and using space that could be devoted to other purposes. Conversion of the refuse to lightweight aggregate could remedy these conditions and effectively utilize a material normally considered waste. The first part of the program was conducted in cooperation with the Truax-Traer Coal Co. to determine the feasibility of utilizing refuse from the company&apos;s coal preparation plant at Ceredo, W. Va., in manufacturing lightweight aggregate. The aggregate was to be used in making cement blocks comparable to those known in the building trades as cinder blocks. This project was completed in 1954. Based on the results of this work, the cooperator began commercial development and formed the Trulite Corp. for this purpose. A plant capable of handling 120 tpd of refuse was constructed for approximately $120,000. It began operating on June 1, 1955.&apos; In 1959 a similar study was made, under a cooperative agreement with the Carbon Fuel Co. of Charleston, W. Va., to rrscertain the suitability of refuse from its plant for conversion to lightweight aggregate. Under this program various modifications of equipment were made, and the investigation of process variables begun in the previous project was extended. PROCESSING METHOD The formation of lightweight aggregate from coal-washery refuse js governed, in part, by the fusion characteristics of the mineral constituents of the refuse when heated above their softening temperatures. The heat required for this purpose is supplied by the combustihle matter in the refuse. Some of this combustible matter is coal with high ash content, but most of it is carbonaceous shale. Whereas the density of aggregate prepared from clay or shale depends largely on expansion, the density of aggregate made from refuse is reduced by burning out the combustible matter and, to a lesser extent, by expansion of the residue in the fuel bed. A chain-grate stoker with an updraft air system was chosen for the conversion process in preference to a downdraft sintering machine or a rotary kiln. In down-draft sintering, which operates on the overfeed burning principle, the volatile matter from the refuse would distill off without burning, resulting in inefficient combustion and interfering with proper operation of the equipment. The rotary kiln is designed primarily for processing material that lacks, or is low in, combustihle matter with the heat of reaction supplied from external sources. Washery refuse, which is relatively high in carbonaceous material, could burn at the wall of the kiln causing clinker formation with resultant decrease in throughput and increase in production cost. With an up-draft air stream on a chain or traveling-grate stoker, the volatile matter would be carried into the ignition and burning zones where the heat could be utilized more efficiently. The combustion procedure in this type of unit may be considered as consisting of four periods: 1) initial ignition of the top of the bed by furnace radiation, 2) ignition travel through the bed until the whole bed is ignited, 3) burnout of the combustible material with high air rates to fuse and expand the residue, 4) a cooling period. Investigation of the process required a study of the variables that affect both

Jan 1, 1962

By Raynor Linzey, Karl M. Busen

The formation of thin films of silicon oxide by anodic oxidation of silicon and the subsequent removal of these films by an etch is a process often used for the evaluation of concentration distributions Profiles) in silicon layers by the differential sheet conductance method. The accuracy of the resulting profile is very strongly influenced by the uniformity of the thickness of the reacted silicon. Normally, it would be expected that for a constant number of coulombs passed the thickness would be the same from oxidation to oxidation. Investigations show that in certain electrolytes, for a given number of coulombs passed through an n-type silicon sample, the thickness of the reacted silicon increased with increasing resistivity. Even for the same resistivity the thickness varied sometimes by a factor of 1.5. When an electrolyte was used which consisted of 10 pct water by volume in ethylene glycol with 4.0 g KNO per 1000 ml of solution, anodiza-tion at 5 ma per sq cm led to satisfying results. Short-time anodizations gave oxide layers of a higher apparent density than those experienced from thermally gown silicon oxides. THE functioning and the electrical characteristics of semiconductor devices are based upon the incorporation of "impurities" into a single-crystalline body of suitable material and on the concentration distribution (profile) of this impurity. The incorporation can be achieved by well-known processes as, for example, by diffusion, epitaxial growth, alloying, or ion implantation. Often the profile resulting from these processes is not known. A powerful tool to learn about a concentration distribution is given by the method of differential sheet conductance which employs successive four-probe measurements on a layer subjected to stepwise removal of thin sublayers. Differential sheet conductance vs position (or penetration depth) of a sublayer is plotted and a smooth curve is drawn through the data. From this curve the profile is then calculated. When the semiconductor material is silicon, the sublayers are removed suitably by anodic oxidation of the silicon and subsequent dissolving of the formed silicon oxide by an etch. The accuracy of the resulting profile is very strongly influenced by the uniformity of the sublayer thickness. Normally, it would be expected that, for a constant number of coulombs passed, the thickness would be constant from oxidation to oxidation. Investigations showed that for sublayers several hundred angstroms thick the reproducibility can be rather poor. Therefore, efforts were made to obtain a reliable technique for uniform removal. The present paper describes such a technique and certain phenomena which were encountered during the investigations. APPARATUS AND TECHNIQUE The first report on the investigation of concentration distributions, where for differential sheet conductance measurements thin silicon sublayers were removed from a diffused layer by anodic oxidation, was given by Tannenbaum. The author reports the removal of sublayers which for the most part were 400 thick. More advanced device designs now require much narrower layers. When it was tried in these laboratories to determine profiles within such layers, difficulties were encountered with respect to sublayers which by necessity had to be thinner than the ones reported by Tannenbaum. The apparatus used for the investigations is sketched in Fig. 1. Two cylindrical containers connected by a wide tube are filled with an electrolyte. The left container receives the cathode whereas the right container is closed at the bottom end by a sample support consisting of a Teflon base and a copper pedestal. The silicon sample (1 by 1 cm) is mounted to the pedestal embedded flush in the Teflon base using silver paint (Degussa) for electrical contact. Pyseal is applied to the edges of the sample to protect the copper pedestal from the electrolyte. The base is mounted to the container using a water-tight silicon rubber gasket. Fig. 2 gives a view of the sample support. The copper pedestal is connected to the positive side of a power supply operating at a constant current output (Kepco Model ABC 425M). The electrolyte which has been reported by Duffek et al. consisted of either 2 or 10 pct water by volume in ethylene glycol and 4.0 g KNO3 in 1000-ml solution. The electrolyte is best prepared

Jan 1, 1967

IN the decade beginning 1850, the development by William Kelly in I the U.S.A. and Henry Bessemer in England of the pneumatic method of refining pig iron, known as the Bessemer process, gave the world the first method of producing low-cost steel in large volumes. Briefly, the Bessemer process consists of blowing air through liquid blast furnace iron in a refractory-lined vessel known as a converter. The air enters the iron in the furnace bottom through tuyeres, and during its passage through the iron removes the carbon, manganese, and silicon by oxidation. The heat produced by oxidation is sufficient to raise the temperature of the liquid metal to normal steel casting temperatures and, in addition, to melt some scrap. In the 1860&apos;s, the open hearth process was introduced which in the early part of the twentieth century surpassed the Bessemer process in steel production. In the early 1870&apos;s, Thomas and Gilchrist discovered that phosphorus could also be removed if lime were added and the converter lined with basic refractory; the modification is known as the basic Bessemer process and is used in Europe. Bessemer steel usually contains between 0.010 and 0.020 per cent nitrogen and between 0.05 and 0.10 per cent phosphorus which influences the properties. Henry Bessemer,1 in 1856, recognized the possibility of using oxygen in the converter process, but the cost was prohibitive. This interest was associated with the theoretical balance of the Bessemer process. Experimental work&apos; has indicated that bottom blowing with pure oxygen results in serious converter bottom and tuyere erosion. Dilution of the oxygen by steam has been observed to be an effective means of maintaining low-nitrogen content of the steel and at the same time reducing bottom and tuyere erosion. A further advantage is that the fume emission characteristic of Bessmer operation is reduced. The addition of steam to the oxygen, however, reduces scrap-melting capacity due to the endothermic reaction characteristics of steam. The possible advantages of refining methods for steel using high-purity oxygen have been recognized for over a hundred years, but the develop-

Jan 1, 1964

By Carroll C. Bailey, William F. Boericke

Mine financing, or providing adequate capital for developing and bringing a mining property into production, is an essential requirement for a successful operation. Today it presents a different picture than even twenty-five years ago. The day appears to be gone when a mining property could pay its own way from grass roots to production. The country has been quite thoroughly combed for surface showings from which sufficient initial profit could be immediately garnered to pay for further development and production facilities. The four M&apos;s for success in mining-mineral, market, management, and money-are still essential, but doubled or tripled wage costs and steep advances in cost of equipment and supplies throw increased emphasis on adequate capital funds for converting a prospect into a producer. Consequently, the old picturesque, although seldom rewarding, grub- staking procedure where a single venturesome citizen might advance funds to a prospector on a fifty-fifty basis for whatever discovery he might find, has largely disappeared. Its place, to some degree, has been taken by the small syndicate of venturesome members who band together for furnishing funds to a group of prospectors for the same general purposes. Such a syndicate has a definite organization and is usually assured of sufficient initial funds, or flow of funds, to carry on work for several years. It is usually headed by an engineer-promoter or an entrepreneur trader who has had considerable field experience as well as personal knowledge of his prospecting crews. For the owner of a potential mining property who has ample capital, the problem is to determine (1) justification for the necessary investment in exploration and development, and (2) the economics of the enterprise as to size and degree of integration of the ha1 operating entity. If the owner of such a property has little or no capital, he also faces these same basic problems but, in addition, must be able to present the findings of fact and persuade the prospective investor that the enterprise will produce

Jan 1, 1964

By N. A. Tiner

A study was made of the effects of temperature, type of loading, and electric polarization on the fracturing behavior of copper and zinc coated with mercury. Copper showed an em-brittlement only in cyclic loading, whereas zinc showed an em-brittlenzent in both static and cyclic loading. The embrittle-ment of zinc in static loading was prevented by sub-zero cooling to a temperatzcre of about -70°F. The emhrittlement of both metals was sliglztly reduced by cathodic polarization of mercury. The basic processes involved in fracturing were discussed in the light of these observations. When a solid metal is in contact with certain liquid metals possessing high wetting characteristics, a weakening effect is produced, and the solid metal fractures in brittle manner at a relatively low stress. This lowering of the fracture stress generally is considered different from the stress cracking caused by a corrosive liquid environment and is attributed to the lowering of the solid-liquid interface tension at the grain boundaries.1-4 The purpose of this paper is to describe a number of observations on the special features of fracturing of copper and zinc coated with a liquid mercury film, and to analyze the basic processes involved in fracturing in the light of these observations. EXPERIMENTAL OBSERVATIONS I) Effect of Type of Loading—The evidence appears to indicate that in static loading, metals usually fracture by the initiation of microcracks in the interior preferentially at the grain boundaries or at the intersection of slip bands.&apos; In cyclic loading, cracks develop on the surface within the active slip zones, and gradually propagate with increasing num- ber of cycles.6&apos;7 Because of this difference in the manner of initiation of cracks, a series of bare and mercury coated copper and zinc specimens was subjected to static and cyclic loading, and their fracturing behavior was examined. The specimens were machined to 0.25 in. in diam and 1 in. in length from a high-purity commercial bar stock, and annealed at an appropriate temperature. Mercury was applied to the surface of the specimens by rubbing with cotton wool soaked in a saturated solution of HgCl2 or by etching with a dilute solution of HC1 and rubbing with purified mercury and by washing in water. The static tension load-extension curves were obtained by means of a Riele Screw Power Universal Testing Machine. The room-temperature load-extension curves for copper and zinc are shown in Fig. 1. The deformation behavior of copper, as judged from the general configuration of the load-extension curve, was not affected by mercury coating. The maximum load to fracture and the elongation at the maximum load were practically the same for both specimens. The mercury coated copper, however, showed somewhat less localized necking and had smaller reduction of area than the uncoated metal. The behavior of mercury coated zinc was radically different from the behavior of uncoated metal. The load-extension curves were the same at the

Jan 1, 1962